Always there to help you
Register your product and get support at
www.philips.com/welcome
Question?
Contact
Philips
User manual
AJ6200D/12
Contents
1Important
3
2 Your clock radio
3
3
4
3 Get started
5
5
6
6
4 Play from iPod/iPhone
7
7
7
7
7
5 Listen to FM radio
8
8
8
8
9
What's in the box Overview of the main unit
Connect power
Set time
Turn on
Compatible iPod/iPhone
Listen to audio from iPod/iPhone Charge the iPod/iPhone
Adjust volume
Tune to FM radio stations
Store FM radio stations automatically
Store FM radio stations manually
Select a preset radio station
6 Other features
9
9
10
10
11
7 Product information
11
11
8Troubleshooting
12
9Notice
12
Set alarm timer
Set sleep timer
Play audio from an external device Adjust display brightness Specifications
EN
2
1Important
Warning
•• Never remove the casing of this clock radio.
•• Never lubricate any part of this clock radio.
•• Never place this clock radio on other electrical
equipment.
•• Keep this clock radio away from direct sunlight, naked
flames or heat.
•• Make sure that you always have easy access to the
2 Your clock radio
Congratulations on your purchase, and
welcome to Philips! To fully benefit from the
support that Philips offers, register your product
at www.philips.com/welcome.
What's in the box
power cord, plug or adaptor to disconnect the clock
radio from the power.
•
•
•
•
•
•
3
Make sure that there is enough free space
around the product for ventilation.
The clock radio shall not be exposed to
dripping or splashing.
Do not place any sources of danger on the
clock radio (e.g. liquid filled objects, lighted
candles).
Where the plug of the Direct Plug-in
Adapter is used as the disconnect device,
the disconnect device shall remain readily
operable.
Only use power supplies listed in the user
manual.
Battery usage CAUTION – To prevent
battery leakage which may result in bodily
injury, property damage, or damage to the
unit:
• Install all batteries correctly, + and - as
marked on the unit.
• Do not mix batteries (old and new or
carbon and alkaline, etc.).
• Remove batteries when the unit is not
used for a long time.
• The batteries should not be exposed
to excessive heat such as sunshine fire
or the like.
EN
Always there to help you
Register your product and get support at
www.philips.com/welcome
AJ6200D
Question?
Contact
Philips
User Manual
Overview of the main unit
e
f
a
b
c
g
h
d
i
j
l
k
BUZZ
FM
DOCK
AU D I O I N
m
n
a SOURCE
• Press to select a source.(DOCK/FM/
AUDIO IN)
• Press and hold for 3 seconds to switch
to standby mode.
b SLEEP
• Set sleep timer.
c SNOOZE/BRIGHTNESS
• Snooze alarm.
• Adjust display brightness.
d Display panel
• Show current information.
e Dock for iPod/iPhone
f AL1/AL2
• View alarm settings.
• Activate or deactivate alarm timer.
g VOLUME +/• Adjust volume.
h First Knob (HOUR/PRESET)
• Adjust hour.
• Select a preset radio station.
i Second Knob (MINUTE/TUNING)
• Adjust minute.
• Tune to an FM radio station.
• Skip to the previous or next track.
EN
4
j Third Knob (SET TIME/SET RADIO/
CLOCK/SET AL1/SET AL2)
• Set time.
• Scan/store FM radio stations.
• Set alarm.
k BUZZ/FM/DOCK
• Select an alarm source for Alarm 1 and
Alarm 2.
l
(5.0 V 1 A)
• Charge your iPod/iPhone through USB
cable (not included).
m AUDIO IN
• Connect an external audio device.
n FM ANT
• Improve FM reception.
3 Get started
Always follow the instructions in this chapter in
sequence.
Connect power
The unit can only be powered by AC power.
Batteries are only used for alarm backup if not
connected with AC power.
Option 1: AC power
Warning
•• Risk of product damage! Make sure that the power
supply voltage corresponds to the voltage printed on
the back or the underside of the unit.
•• Risk of electric shock! When you disconnect the AC
power, always pull the plug from the socket. Never pull
the cord.
Connect the AC power cord to the wall socket.
Tip
•• To save energy, turn the unit off after use.
5
EN
Option 2: Battery power
Caution
•• Batteries contain chemical substances, so they should
Set time
1
be disposed of properly.
Note
•• Batteries are not supplied with the accessories.
•• bAt shows on the display when the battery level is low.
1
2
3
Open the battery compartment.
Insert 2 batteries (type: 1.5V LR6/AA) with
correct polarity (+/-) as indicated.
Close the battery compartment.
2
3
4
5
Rotate the Third Knob to "SET TIME" to
activate clock setting mode.
»» Hour and minute digits blinks.
Rotate the First Knob to adjust the hour.
Rotate the Second Knob to adjust the
minute.
Press OK on the First Knob to confirm.
»» The setting time is displayed.
Rotate the Third Knob to CLOCK after
setting.
»» The hour and minute digits stops
blinking.
Note
•• When an iPod/iPhone is connected, the clock radio
synchronizes time from the iPod/iPhone automatically.
Turn on
The clock radio turns on automatically once
your plugged in.
Switch to standby mode
Press SOURCE for 3 seconds to switch to
standby mode.
»» The source indicator on the display panel
turns off.
EN
6
4 Play from iPod/
iPhone
You can enjoy audio from iPod/iPhone through
this clock radio.
Compatible iPod/iPhone
The clock radio supports these iPod and iPhone
models:
Made for.
• iPod touch (5th generation)
• iPod nano (7th generation)
• iPhone 5
Listen to audio from iPod/
iPhone
Note
•• Make sure that the Third Knob switched to CLOCK
before setting.
1
2
3
4
Place the iPod/iPhone in the dock.
Press SOURCE repeatedly to select iPod/
iPhone mode.
»» The
on the display panel lights up.
Play audio on the iPod/iPhone.
Rotate the Second Knob to select
previous or next track.
To remove the iPod/iPhone:
Pull the iPod/iPhone out of the dock.
7
EN
Charge the iPod/iPhone
When the clock radio is connected to power,
the docked iPod/iPhone starts charging.
Adjust volume
You can adjust volume by pressing VOLUME
+/- repeatedly.
5 Listen to FM
radio
Store FM radio stations
automatically
Note
•• You can store a maximum of 20 FM radio stations.
Tune to FM radio stations
1
Tip
•• Position the antenna as far as possible from TV, VCR, or
other radiation source.
2
•• For better reception, fully extend and adjust the
position of the antenna.
Note
•• Make sure that the Third Knob switched to CLOCK
before setting.
1
2
3
Press SOURCE repeatedly to select FM
tuner source.
»» FM on the display panel lights up.
Rotate and hold the Second Knob for two
seconds.
»» The clock radio tunes to a station with
strong reception automatically.
Repeat step 2 to tune in to more radio
stations.
To tune to a station manually:
Rotate the Second Knob repeatedly until you
find optimal reception.
In FM mode, rotate the Third knob to SET
RADIO.
»» FM begins to blink.
Press and hold OK on the First Knob for
three seconds.
»» The clock radio stores all the available
FM radio stations, and broadcasts the
first available station automatically.
Store FM radio stations
manually
1
2
3
4
5
In FM mode, rotate the Third Knob to
SET RADIO.
»» FM begins to blink.
Rotate and hold the Second Knob for two
seconds.
»» The last selected channel is displayed
on the display panel.
Rotate the First Knob again to select the
target preset position.
Press OK on the First Knob to confirm.
Repeat steps 2-4 to store other stations.
Note
•• To remove a pre-stored station, store another station
in its place.
EN
8
Select a preset radio station
6 Other features
Note
•• Make sure that the Third Knob switched to CLOCK
before setting.
1
2
Press SOURCE repeatedly to select FM
tuner source.
»» FM on the display lights up.
Rotate the First Knob repeatedly to select
a preset radio station.
Set alarm timer
In standby mode, you can set two alarms to ring
at different time.
Note
•• Make sure that you have set the clock correctly.
1
2
3
4
5
Rotate the Third Knob to SET AL1 or SET
AL2 to activate alarm setting mode.
»» The
/ and time digits blink.
Rotate the First Knob to adjust the hour.
Rotate the Second Knob to adjust the
minute.
Press OK on First Knob to confirm.
Rotate the Third Knob to CLOCK after
setting.
Select alarm source
For alarm sound, you can select buzzer, your last
listened radio station, or the last played audio
on your iPod/iPhone.
Tip
•• If DOCK is selected as the alarm source, yet the audio
cannot be played, buzzer will sound when alarm time
comes.
•• If FM is selected as the alarm source and the speaker is
playing under FM mode, buzzer will sound when alarm
time comes.
9
EN
Set sleep timer
Note
•• Make sure that the Third Knob switched to CLOCK
before setting.
BUZZ
FM
DOCK
Activate/deactivate alarm timer
Note
•• Make sure that the Third Knob switched to CLOCK
before setting.
1
2
This clock radio can switch to standby mode
automatically after a preset period.
• Press SLEEP repeatedly to select the sleep
timer period (in minutes).
»» When the sleep timer is activated,
appears.
To deactivate the sleep timer:
• Press SLEEP repeatedly until [OFF] (off)
appears.
15
• To stop the ringing alarm, press the
corresponding AL1/AL2.
»» The alarm repeats ringing for the next
day.
Snooze the alarm
When alarm sounds, press SNOOZE.
»» The alarm snoozes and repeats ringing
nine minutes later.
60
90
120
OFF
Press AL1/AL2 to view alarm settings.
»» The
/ lights up.
Press AL1/AL2 again to activate or
deactivate the alarm timer.
»» The
/ appears if alarm timer is
on and disappears if it is off.
30
Play audio from an external
device
Note
•• Make sure that the Third Knob switched to CLOCK
before setting.
You can listen to audio from an external device
through this clock radio.
1
2
3
Connect an audio cable to:
• the AUDIO IN socket on the clock
radio.
• the headphone socket on an external
device.
Press SOURCE repeatedly to select the
Audio-in source.
»» The
on the display panel lights up.
Play the external device (refer to its user
manual).
EN
10
7Product
information
Note
•• Product information is subject to change without prior
notice.
Specifications
Adjust display brightness
Amplifier
Rated Output Power
5W RMS
SNOOZE
BRIGHTNESS
Tuner
Tuning Range
Sensitivity
- Mono, 26dB S/N Ratio
Search Selectivity
Total Harmonic Distortion
Signal to Noise Ratio
FM: 87.5 - 108
MHz
FM: <22 dBf
FM: <30 dBf
FM: <3%
FM: >50 dBA
General information
AC Power
Operation Power
Consumption
Standby Power
Consumption
Dimensions - Main
Unit (W x H x D)
Weight - Main Unit
11
EN
Model:
ASSA36E-090160;
Input: 100-240 V ~,
50/60Hz, 0.6A; Output:
9.0V 1600 mA
<15 W
<1 W
195 x 99 x 113 mm
0.79 kg
8Troubleshooting
9Notice
Warning
•• Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support). When you contact Philips,
make sure that the device is nearby and the
model number and serial number are available.
No power
•• Ensure that the power cord is connected
securely.
•• Ensure that there is power at the power
supply socket.
•• Ensure that the batteries are installed
correctly.
No response from the clock radio
•• Disconnect and reconnect the AC power
plug, then turn on the clock radio again.
Poor radio reception
•• Keep the clock radio away from other
electronic devices to avoid radio
interference.
•• Fully extend and adjust the position of the
FM antenna.
Alarm does not work
•• Set the clock/alarm correctly.
Clock/alarm setting erased
•• Power has been interrupted or the power
plug has been disconnected.
•• Reset the clock/alarm.
This product complies with the radio
interference requirements of the European
Community.
Any changes or modifications made to this
device that are not expressly approved by
WOOX Innovations may void the user’s
authority to operate the equipment.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC.
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negative consequences for the environment and
human health.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.Please inform yourself about the local
EN
12
rules on separate collection of batteries
because correct disposal helps to prevent
negative consequences for the environmental
and human health.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
“Made for iPod” and “Made for iPhone”
mean that an electronic accessory has been
designed to connect specifically to iPod or
iPhone respectively, and has been certified by
the developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note that
the use of this accessory with iPod or iPhone
may affect wireless performance.
iPod and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries.
Note
•• The type plate is located on the bottom of the
apparatus.
13
EN
Specifications are subject to change without notice
2013 © WOOX Innovations Limited. All rights reserved.Philips
and the Philips’ Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used by WOOX Innovations
Limited under license from Koninklijke Philips N.V.
AJ6200D_12_UM_V2.0