Bosch Exxcel WVH28360GB washer dryer

Safety instructions
Installation area
– The washer dryer is heavy – take care when lifting it.
– Warning: frozen hoses may tear/burst. Do not install the washer dryer outdoors or in areas
where there is a risk of frost.
– The washer dryer may be damaged. Do not lift by moveable components (e.g. washer dryer
door).
– In addition to the instructions mentioned here, special regulations regarding the relevant
water and power supply companies may apply.
– If in doubt, have the appliance connected by a technician.
– Lay hoses and cables in such a way that there is no risk that they can be tripped over.
Environmentally friendly disposal
– Dispose of packaging in an environmentally friendly manner.
– This appliance has been identified in accordance with the European Directive
2002/96/EEC on Waste Electrical and Electronic Equipment (WEEE). This directive
specifies a framework for the return and recycling of waste appliances, and is valid
throughout Europe.
–
–
–
–
Water connection Removing the transport bolts
Stability is important to prevent the machine from wandering.
The installation area must be firm and level.
Soft floors/floor coverings are not suitable.
Ensure the area is well ventilated to achieve good drying performance.
– Risk of electric shock. Do not immerse the Aqua-Stop safety device in water
(contains an electric valve).
– To prevent leakage or water damage, follow the instructions in this chapter.
– Note: operate the washer dryer with cold mains water only.
Do not connect to the mixer tap of a pressureless hot-water heater.
– Do not use a used inlet hose. Only use the inlet hose supplied or one which was
purchased from an authorised specialist dealer.
– If in doubt, have the appliance connected by a technician.
– Before using the appliance for the first time, always remove and retain
all 4 transport bolts.
– If transporting the appliance at a later date, always re-install the
transport bolts – this prevents damage to the machine. a Page 6
– Retain the screw and sleeve.
If installing the appliance on a platform
– It is essential to secure the washer dryer feet with holding brackets *.
1. Take the hoses out of the holder and the elbow.
If installing the appliance on a wooden joist floor
– If possible, install the washer dryer in a corner.
– Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.
– It is essential to secure the washer dryer feet with holding brackets *.
* order no. WMZ 20490, WZ 20490
or
High levels of noise, intense vibrations and “walking” may be due to incorrect alignment.
Alignment will be carried out by customer service or authorised technicians; if you want
to align the machine by yourself please use a spirit level.
Aligning the washer dryer with a spirit level.
Water supply
Water inlet hose:
Note: Do not bend, crush, modify or cut through the hose (the strength is no longer guaranteed).
Optimum water pressure in the mains: 100-1000 kPa (1-10 bar)
– When the tap is turned on, the water flow is at least 8 l/min.
– If the water pressure is higher, install a pressure reducing valve.
Hose and cable lengths
Connection on left side
Alignment
Model:
2. Undo and remove all 4 transport bolts.
Aqua-Stop
Aqua-Secure
1. Connect the water supply hose to the tap.
Tighten the plastic screw fittings by hand only.
Connection on right side
Standard
3/4 ’’
1. Undo the lock nut in a clockwise direction using a wrench.
2. Adjust the height by turning the appliance foot.
All four appliance feet must be placed firmly on the floor.
The washer dryer must not be able to wobble.
Check the alignment of the washer dryer with a spirit level and
correct if necessary.
min. 10 mm
Scope of delivery according to the model
Humidity in the drum is caused
by the final inspection.
~140 cm
2. Carefully turn on the tap and check that the
connection points are not leaking.
Note: The screw connection is under water
mains pressure.
~90 cm
3. Take the power cord out of the holders. Remove the sleeves.
Aqua-Stop
Aqua-Secure
Standard
max.
90°
max.
90°
3. Tighten the lock nut against the housing.
Hold the foot in place and ensure that the height is not adjusted.
The lock nuts on all four appliance feet must be screwed tightly against
the housing.
3/4 ’’
Power cord
Covers
Hose holder
~160 cm
~140 cm
~165 cm
min. 60 cm
~95 cm
Water supply
max. 100 cm
min 10 mm
Water drainage
Water drainage
Note: If hose holders are used, the hose lengths may be reduced.
Available from dealer/after-sales service:
– Aqua-Stop extension hose **, approx. 2.50 m.
– Longer supply hose, approx. 2.20 m, for standard model.
Height difference between the installation area and outlet: 60–100 cm
Drainage into a sink/bath tub:
Note: Secure the drainage hose to prevent it from slipping out of the sink.
** order no. WMZ 2380, WZ 10130
Elbow
for fixing the waste
water hose
Build these appliances under/in before connection to the power supply.
Note: The plug must not be in the plug hole. When the water is being
pumped out of the washer dryer, check that the water drains away quickly
enough. Do not immerse the end of the drainage hose in the water that has
been pumped out. There is a risk that water will be drawn back into the
washer dryer.
Installed in between kitchen units (built-under or built-in)
Drainage into a siphon:
Note: Secure the connection with a 24-40 mm dia. hose clip (available from
a specialist retailer).
Built-under/built-in appliances
Depending on the connection
– A 24–40 mm dia. hose clip may also be required for connecting the siphon (available from
specialist retailers). a Page 4: Water connection
– 62 cm cavity width required.
– Install the washer dryer only under a continuous worktop that is connected firmly to the
adjacent cupboards.
Useful tool
– Spirit level for aligning the washer dryer.
– Wrench for adjusting the machine feet.
Drainage into a plastic pipe with rubber sleeve:
Note: secure the drainage hose to prevent it from slipping out
of the drain.
5. Fix the hoses in the hose holders.
1
Electrical connection
Water drainage hose:
Note: Do not kink or stretch.
4. Insert the covers and lock them in place by pressing on the locking hook. Insert the hose
holders.
2
3
4
ʑ
ʑ
ʑ
ʑ
Connect the washer dryer to an alternating current using a correctly installed earthed socket
only.
ʑ
ʑ
ʑ
ʑ
A damaged power cord must be replaced by an electrician only.
Replacement power cords are available from after-sales service.
The mains voltage and specifications on the washer dryer must match.
a Page 6: Technical specifications
For information about the connected load and required fuse.
a Page 6: Technical specifications
Ensure that:
– the mains plug and socket are compatible,
– the cable cross-section is adequate,
– the earthing system has been installed correctly.
Do not use multiple plugs/connectors or extension cables.
If a residual current-operated circuit-breaker is used, only use the type which complies with
current regulations.
Mains plug:
– Do not insert into/pull out of the socket with damp hands.
– do not pull the plug out of the socket by pulling on the power cord.
– never pull out the plug while the appliance is in operation.
Manufacturer (see Operating instructions)
9306/ 9000 829281
5
Transportation, e.g. when moving house
– Risk of electric shock.
Pull out the mains plug.
– Risk of explosion. No solvents.
Care
1. Before transporting the washer dryer:
Maintenance
1. Turn off the tap.
2. Release the water pressure in the supply hose.
a Page 8: Filter in the water inlet hose
3. Drain any residual detergent solution.
a Page 8: Draining the pump
4. Disconnect the washer dryer from the power supply.
5. Remove the hoses.
Aqua-Stop warranty for appliances with Aqua-Stop only
Draining the pump
Machine housing, control panel
–
–
–
–
– Risk of scalding.
Allow detergent solution to cool down.
– Turn off the tap.
2. The liability warranty applies to the service life of the appliance.
... if it contains detergent or fabric softener residue.
3. A claim can only be made under the warranty if the appliance and Aqua-Stop have been
correctly installed and connected according to our instructions; this also includes a correctly
installed Aqua-Stop extension (genuine accessory).
Our warranty does not extend to defective supply lines or fittings up to the Aqua-Stop
connection on the tap.
2. Release the drainage hose from the clip.
Remove the sealing plug from the drainage hose and allow the detergent
solution to flow out. Push the sealing cap back in.
1. Pull the drawer out until the stop position, press down the latch
on the insert and remove the drawer completely.
4. Appliances which feature Aqua-Stop can be left unattended during operation and it is not
necessary to turn off the tap afterwards.
The tap should only be turned off if you are away for a prolonged period, e.g. several weeks
holiday.
2. Remove insert: Pull the insert upwards using your finger.
1. Remove the covers. If necessary, remove the
retainer as shown in the picture on the right.
3. Clean the detergent dispenser and the insert with water and a brush.
3. Remove the pump cap. Remove foreign objects/loose debris/fluff
from inside and clean the pump. (The impeller in the pump must be
able to rotate).
4. Refit the insert and secure it in place (the cylinder should fit over the
guide pin).
4. Clean any residual lye or fluff from the thread of the pump cap
and pump housing.
Installation and
maintenance instructions
5. Insert the detergent drawer.
2. Insert all sleeves.
Clamp the power cord into
the holders.
Insert the bolts and tighten.
5. Attach the pump cap and screw it on tight until the stop; the handle
should be pointing upwards. Place the drainage hose back in the
retainer.
6. Leave the detergent drawer open so that residual water can evaporate.
Drum
Ensure that there is no laundry in the machine!
This is not necessary if the detergent is dispensed correctly. However, if it is necessary, follow
the instructions provided by the descaler manufacturer. Suitable descaling products can be
purchased from our website or after-sales service.
Technical specifications
ʑ
ʑ
ʑ
ʑ
ʑ
ʑ
Dimensions (width x depth x height)
600 x 600 x 850 mm
Weight
81 kg
Power supply
Nominal voltage 220–240 V, 50 Hz
Max. current 10A
Max. washing power 2400 W
Max. drying power 1900 W
Water pressure
100-1000 kPa (1-10 bar)
Drain height
60–100 cm
Test programmes
According to applicable European Standard
EN50229
After-sales service
If you cannot rectify the fault yourself a Operating instructions, page 12, 13: What to do if...,
ʑ please
contact our after-sales service. We will always find a suitable solution and will avoid a
visit from a service technician wherever possible.
ʑ
ʑ
Please give the after-sales service the product number (E-Nr.) and the production number
(FD) of the appliance.
ʑ
6
Production number
Filter in the water inlet hose
Risk of electric shock
Do not immerse the Aqua-Stop safety device in water (it contains an electric valve).
Reduce the water pressure in the supply hose:
1.
2.
3.
4.
Turn off the tap.
Select any programme (except Spin or Empty(Drain)).
Touch Start button and allow the programme to run for approx. 40 seconds.
Set the programme selector to Off. Disconnect the mains plug.
Clean the filter:
The contact details for all countries can be found in the after-sales service directory enclosed.
Product number
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
To prevent unused detergent from flowing straight into the drain during
the next wash cycle: pour 1 litre of water into compartment II and start
the Spin programme. Then select and start a new washing programme
with detergent as usual.
Descaling To prevent unused detergent from flowing into the outlet during the next wash:
Pour 1 litre of water into dispenser II and start the Empty (Drain) or Spin programme.
Contents
6. Place the service flap back on and close.
Leave the washer dryer door open after washing so that the drum can dry.
Rust stains – use chlorine–free cleaning agent, not steel wool.
The transport bolts must be removed after transportation. a Page 3
en
1. If water damage was caused by a fault in our Aqua-Stop system, we shall compensate private
users for damage.
1. Open and remove the service flap.
Clean the detergent drawer ...
2. Installing transport bolts:
Washer dryer
In addition to warranty claims against the seller based on the contract of sale and in addition
to our appliance warranty, we shall pay damages under the following conditions:
Set the programme selector to Off, disconnect the mains plug.
Wipe with a soft, damp cloth.
Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
Immediately remove laundry and cleaning agent residues.
Do not clean the appliance with a water jet.
You will find this information:
on the inside of the washer dryer door*/opened
service flap* and rear of the appliance.
*depending on the model
Rely on the professionalism of the manufacturer. Please contact us.
This will ensure that the repair is carried out by trained service technicians who arrive
equipped with genuine spare parts for your appliance.
7
1. Depending on model: Remove the supply hose from the tap.
Clean the filter with a small brush.
and/or on standard and Aqua-Secure models:
Remove the hose from the rear, remove the filter
using pliers and clean the filter.
2. Reconnect the supply hose and check
that it is tight.
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmentally-friendly disposal . . . . . . . . . . . . . . .
Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation area . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hose and cable lengths . . . . . . . . . . . . . . . . . . . . .
Built-under/built-in appliances . . . . . . . . . . . . . . . . .
Removing the transport bolts . . . . . . . . . . . . . . . . .
Water connection . . . . . . . . . . . . . . . . . . . . . . . . . .
Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . .
Transportation, e.g. if moving house . . . . . . . . . . . .
Technical specifications. . . . . . . . . . . . . . . . . . . . . .
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
After-sales service . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aqua-Stop warranty . . . . . . . . . . . . . . . . . . . . . . . . .
Page
...1
...1
...1
...2
...2
...2
...3
...4
...5
...5
...6
...6
...7
...7
...8
...9
Read these instructions before switching on the washer dryer.
Also follow the separate Operating instructions.
Retain all documents for subsequent use or for the next owner.
8
9
Safety instructions
Installation area
– The washer dryer is heavy – take care when lifting it.
– Warning: frozen hoses may tear/burst. Do not install the washer dryer outdoors or in areas
where there is a risk of frost.
– The washer dryer may be damaged. Do not lift by moveable components (e.g. washer dryer
door).
– In addition to the instructions mentioned here, special regulations regarding the relevant
water and power supply companies may apply.
– If in doubt, have the appliance connected by a technician.
– Lay hoses and cables in such a way that there is no risk that they can be tripped over.
Environmentally friendly disposal
Scope of delivery according to the model
Aqua-Secure
If installing the appliance on a platform
– It is essential to secure the washer dryer feet with holding brackets *.
If installing the appliance on a wooden joist floor
– If possible, install the washer dryer in a corner.
– Screw a water-resistant wooden panel (min. 30 mm thick) to the floor.
– It is essential to secure the washer dryer feet with holding brackets *.
* order no. WMZ 20490, WZ 20490
Hose and cable lengths
or
Connection on left side
Humidity in the drum is caused
by the final inspection.
~140 cm
Connection on right side
~90 cm
Standard
Water drainage
~95 cm
Water supply
Power cord
Covers
Hose holder
~160 cm
~140 cm
~165 cm
max. 100 cm
Aqua-Stop
Stability is important to prevent the machine from wandering.
The installation area must be firm and level.
Soft floors/floor coverings are not suitable.
Ensure the area is well ventilated to achieve good drying performance.
min. 60 cm
– Dispose of packaging in an environmentally friendly manner.
– This appliance has been identified in accordance with the European Directive
2002/96/EEC on Waste Electrical and Electronic Equipment (WEEE). This directive
specifies a framework for the return and recycling of waste appliances, and is valid
throughout Europe.
–
–
–
–
Note: If hose holders are used, the hose lengths may be reduced.
Available from dealer/after-sales service:
– Aqua-Stop extension hose **, approx. 2.50 m.
– Longer supply hose, approx. 2.20 m, for standard model.
** order no. WMZ 2380, WZ 10130
Elbow
for fixing the waste
water hose
Built-under/built-in appliances
Build these appliances under/in before connection to the power supply.
Depending on the connection
– A 24–40 mm dia. hose clip may also be required for connecting the siphon (available from
specialist retailers). a Page 4: Water connection
Installed in between kitchen units (built-under or built-in)
– 62 cm cavity width required.
– Install the washer dryer only under a continuous worktop that is connected firmly to the
adjacent cupboards.
Useful tool
– Spirit level for aligning the washer dryer.
– Wrench for adjusting the machine feet.
1
2
Water connection Removing the transport bolts
– Risk of electric shock. Do not immerse the Aqua-Stop safety device in water
(contains an electric valve).
– To prevent leakage or water damage, follow the instructions in this chapter.
– Note: operate the washer dryer with cold mains water only.
Do not connect to the mixer tap of a pressureless hot-water heater.
– Do not use a used inlet hose. Only use the inlet hose supplied or one which was
purchased from an authorised specialist dealer.
– If in doubt, have the appliance connected by a technician.
– Before using the appliance for the first time, always remove and retain
all 4 transport bolts.
– If transporting the appliance at a later date, always re-install the
transport bolts – this prevents damage to the machine. a Page 6
– Retain the screw and sleeve.
1. Take the hoses out of the holder and the elbow.
Water supply
Water inlet hose:
Note: Do not bend, crush, modify or cut through the hose (the strength is no longer guaranteed).
Optimum water pressure in the mains: 100-1000 kPa (1-10 bar)
– When the tap is turned on, the water flow is at least 8 l/min.
– If the water pressure is higher, install a pressure reducing valve.
Model:
2. Undo and remove all 4 transport bolts.
Aqua-Stop
Aqua-Secure
1. Connect the water supply hose to the tap.
Tighten the plastic screw fittings by hand only.
Standard
3/4 ’’
min. 10 mm
2. Carefully turn on the tap and check that the
connection points are not leaking.
Note: The screw connection is under water
mains pressure.
3. Take the power cord out of the holders. Remove the sleeves.
max.
90°
max.
90°
3/4 ’’
min 10 mm
Water drainage
Water drainage hose:
Note: Do not kink or stretch.
4. Insert the covers and lock them in place by pressing on the locking hook. Insert the hose
holders.
Height difference between the installation area and outlet: 60–100 cm
Drainage into a sink/bath tub:
Note: Secure the drainage hose to prevent it from slipping out of the sink.
Note: The plug must not be in the plug hole. When the water is being
pumped out of the washer dryer, check that the water drains away quickly
enough. Do not immerse the end of the drainage hose in the water that has
been pumped out. There is a risk that water will be drawn back into the
washer dryer.
Drainage into a siphon:
Note: Secure the connection with a 24-40 mm dia. hose clip (available from
a specialist retailer).
Drainage into a plastic pipe with rubber sleeve:
Note: secure the drainage hose to prevent it from slipping out
of the drain.
5. Fix the hoses in the hose holders.
3
4
Alignment
High levels of noise, intense vibrations and “walking” may be due to incorrect alignment.
Alignment will be carried out by customer service or authorised technicians; if you want
to align the machine by yourself please use a spirit level.
Aligning the washer dryer with a spirit level.
1. Undo the lock nut in a clockwise direction using a wrench.
2. Adjust the height by turning the appliance foot.
All four appliance feet must be placed firmly on the floor.
The washer dryer must not be able to wobble.
Check the alignment of the washer dryer with a spirit level and
correct if necessary.
3. Tighten the lock nut against the housing.
Hold the foot in place and ensure that the height is not adjusted.
The lock nuts on all four appliance feet must be screwed tightly against
the housing.
Electrical connection
ʑ
ʑ
ʑ
ʑ
Connect the washer dryer to an alternating current using a correctly installed earthed socket
only.
ʑ
ʑ
ʑ
ʑ
A damaged power cord must be replaced by an electrician only.
Replacement power cords are available from after-sales service.
The mains voltage and specifications on the washer dryer must match.
a Page 6: Technical specifications
For information about the connected load and required fuse.
a Page 6: Technical specifications
Ensure that:
– the mains plug and socket are compatible,
– the cable cross-section is adequate,
– the earthing system has been installed correctly.
Do not use multiple plugs/connectors or extension cables.
If a residual current-operated circuit-breaker is used, only use the type which complies with
current regulations.
Mains plug:
– Do not insert into/pull out of the socket with damp hands.
– do not pull the plug out of the socket by pulling on the power cord.
– never pull out the plug while the appliance is in operation.
Manufacturer (see Operating instructions)
9306/ 9000 829281
5
Transportation, e.g. when moving house
Care
1. Before transporting the washer dryer:
Machine housing, control panel
–
–
–
–
1. Turn off the tap.
2. Release the water pressure in the supply hose.
a Page 8: Filter in the water inlet hose
3. Drain any residual detergent solution.
a Page 8: Draining the pump
4. Disconnect the washer dryer from the power supply.
5. Remove the hoses.
2.
– Risk of electric shock.
Pull out the mains plug.
– Risk of explosion. No solvents.
Wipe with a soft, damp cloth.
Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
Immediately remove laundry and cleaning agent residues.
Do not clean the appliance with a water jet.
Clean the detergent drawer ...
... if it contains detergent or fabric softener residue.
1. Pull the drawer out until the stop position, press down the latch
on the insert and remove the drawer completely.
Installing transport bolts:
2. Remove insert: Pull the insert upwards using your finger.
1. Remove the covers. If necessary, remove the
retainer as shown in the picture on the right.
3. Clean the detergent dispenser and the insert with water and a brush.
4. Refit the insert and secure it in place (the cylinder should fit over the
guide pin).
5. Insert the detergent drawer.
2. Insert all sleeves.
Clamp the power cord into
the holders.
Insert the bolts and tighten.
6. Leave the detergent drawer open so that residual water can evaporate.
Drum
Leave the washer dryer door open after washing so that the drum can dry.
Rust stains – use chlorine–free cleaning agent, not steel wool.
The transport bolts must be removed after transportation. a Page 3
Descaling Ensure that there is no laundry in the machine!
This is not necessary if the detergent is dispensed correctly. However, if it is necessary, follow
the instructions provided by the descaler manufacturer. Suitable descaling products can be
purchased from our website or after-sales service.
To prevent unused detergent from flowing into the outlet during the next wash:
Pour 1 litre of water into dispenser II and start the Empty (Drain) or Spin programme.
Technical specifications
ʑ
ʑ
ʑ
Dimensions (width x depth x height)
600 x 600 x 850 mm
Weight
81 kg
Power supply
Nominal voltage 220–240 V, 50 Hz
Max. current 10A
Max. washing power 2400 W
Max. drying power 1900 W
ʑ
ʑ
ʑ
Water pressure
100-1000 kPa (1-10 bar)
Drain height
60–100 cm
Test programmes
According to applicable European Standard
EN50229
After-sales service
you cannot rectify the fault yourself a Operating instructions, page 12, 13: What to do if...,
ʑ Ifplease
contact our after-sales service. We will always find a suitable solution and will avoid a
visit from a service technician wherever possible.
ʑ
ʑ
The contact details for all countries can be found in the after-sales service directory enclosed.
Please give the after-sales service the product number (E-Nr.) and the production number
(FD) of the appliance.
Product number
ʑ
6
Production number
You will find this information:
on the inside of the washer dryer door*/opened
service flap* and rear of the appliance.
*depending on the model
Rely on the professionalism of the manufacturer. Please contact us.
This will ensure that the repair is carried out by trained service technicians who arrive
equipped with genuine spare parts for your appliance.
7
Maintenance
– Risk of scalding.
Allow detergent solution to cool down.
– Turn off the tap.
Aqua-Stop warranty for appliances with Aqua-Stop only
Draining the pump
In addition to warranty claims against the seller based on the contract of sale and in addition
to our appliance warranty, we shall pay damages under the following conditions:
Set the programme selector to Off, disconnect the mains plug.
1. If water damage was caused by a fault in our Aqua-Stop system, we shall compensate private
users for damage.
1. Open and remove the service flap.
2. The liability warranty applies to the service life of the appliance.
3. A claim can only be made under the warranty if the appliance and Aqua-Stop have been
correctly installed and connected according to our instructions; this also includes a correctly
installed Aqua-Stop extension (genuine accessory).
Our warranty does not extend to defective supply lines or fittings up to the Aqua-Stop
connection on the tap.
2. Release the drainage hose from the clip.
Remove the sealing plug from the drainage hose and allow the detergent
solution to flow out. Push the sealing cap back in.
4. Appliances which feature Aqua-Stop can be left unattended during operation and it is not
necessary to turn off the tap afterwards.
The tap should only be turned off if you are away for a prolonged period, e.g. several weeks
holiday.
3. Remove the pump cap. Remove foreign objects/loose debris/fluff
from inside and clean the pump. (The impeller in the pump must be
able to rotate).
4. Clean any residual lye or fluff from the thread of the pump cap
and pump housing.
5. Attach the pump cap and screw it on tight until the stop; the handle
should be pointing upwards. Place the drainage hose back in the
retainer.
6. Place the service flap back on and close.
To prevent unused detergent from flowing straight into the drain during
the next wash cycle: pour 1 litre of water into compartment II and start
the Spin programme. Then select and start a new washing programme
with detergent as usual.
Filter in the water inlet hose
Risk of electric shock
Do not immerse the Aqua-Stop safety device in water (it contains an electric valve).
Reduce the water pressure in the supply hose:
1.
2.
3.
4.
Turn off the tap.
Select any programme (except Spin or Empty(Drain)).
Touch Start button and allow the programme to run for approx. 40 seconds.
Set the programme selector to Off. Disconnect the mains plug.
Clean the filter:
1. Depending on model: Remove the supply hose from the tap.
Clean the filter with a small brush.
and/or on standard and Aqua-Secure models:
Remove the hose from the rear, remove the filter
using pliers and clean the filter.
2. Reconnect the supply hose and check
that it is tight.
8
9
Washer dryer
en
Installation and
maintenance instructions
Contents
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
ʋ
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmentally-friendly disposal . . . . . . . . . . . . . . .
Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation area . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hose and cable lengths . . . . . . . . . . . . . . . . . . . . .
Built-under/built-in appliances . . . . . . . . . . . . . . . . .
Removing the transport bolts . . . . . . . . . . . . . . . . .
Water connection . . . . . . . . . . . . . . . . . . . . . . . . . .
Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . .
Transportation, e.g. if moving house . . . . . . . . . . . .
Technical specifications. . . . . . . . . . . . . . . . . . . . . .
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
After-sales service . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aqua-Stop warranty . . . . . . . . . . . . . . . . . . . . . . . . .
Page
...1
...1
...1
...2
...2
...2
...3
...4
...5
...5
...6
...6
...7
...7
...8
...9
Read these instructions before switching on the washer dryer.
Also follow the separate Operating instructions.
Retain all documents for subsequent use or for the next owner.