Lenovo Miix 10 64GB Black, White Hardware Maintenance Manual

Lenovo IdeaPad
Miix 10
Hardware
Maintenance
Manual
Note:
Before using this information and the product it supports, be sure to read the general information under
“Notices” on page 64.
First Edition (June. 2013)
© Copyright Lenovo 2013. All rights reserved.
LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General
Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set
forth in Contract No. GS-35F-05925.
© 2013 Lenovo
Contents
About this manual........................................ iv
Safety information......................................... 1
General safety................................................. 2
Electrical safety............................................... 3
Safety inspection guide................................... 5
Handling devices that are sensitive to
electrostatic discharge..................................... 6
Grounding requirements.................................. 6
Safety notices: multilingual translations.......... 7
Laser compliance statement......................... 14
Important service information.................... 16
Strategy for replacing FRUs.......................... 16
Locations....................................................... 54
Top view.............................................................54
Front view..........................................................55
Bottom view, Left-side and Rear view ..............56
Parts list......................................................... 57
Overall...............................................................58
Keyboard...........................................................60
Miscellaneous parts...........................................61
Screws...............................................................62
AC adapters.......................................................63
Notices......................................................... 64
Trademarks................................................... 65
Important notice for replacing a system board ......17
Important information about replacing RoHS
compliant FRUs............................................. 18
General checkout ....................................... 19
What to do first.............................................. 20
Power system checkout................................ 21
Checking the AC adapter ..................................21
Checking operational charging..........................21
Related service information....................... 23
Restoring the factory contents by using
Recovery system........................................... 23
Restore of factory default..................................23
Passwords..................................................... 24
Power-on password...........................................24
Supervisor password ........................................24
Power management...................................... 25
Screen blank mode............................................25
Sleep (standby) mode.......................................25
Lenovo IdeaPad Miix 10.............................. 26
Specifications................................................ 26
Function key combinations............................ 28
FRU replacement notices.............................. 29
Screw notices ...................................................29
Removing and replacing an FRU.................. 30
1010 LCD cover.................................................31
1020 Battery pack..............................................32
1030 3G card ....................................................34
1040 Speakers..................................................36
1050 Audio Board..............................................38
1060 Power board.............................................40
1070 Docking Board..........................................42
1080 Touch Pad Board......................................43
1090 System board............................................. 45
1100 PCI Express Mini Card for wireless LAN......48
1110 Integrated camera ....................................50
1120 Antenna Module........................................51
iii
About this manual
This manual contains service and reference information for the following
Lenovo IdeaPad product:
Lenovo IdeaPad Miix 10
Use this manual to troubleshoot problems.
The manual is divided into the following sections:
• The common sections provide general information, guidelines, and safety
information required for servicing computers.
• The product-specific section includes service, reference, and product-specific
parts information.
Important:
This manual is intended only for trained servicers who are familiar with Lenovo
IdeaPad products. Use this manual to troubleshoot problems effectively.
Before servicing a Lenovo IdeaPad product, make sure to read all the information
under “Safety information” on page 1 and “Important service information” on page
16.
iv
Safety information
Safety information
This chapter presents the following safety information that you need to get
familiar with before you service an Lenovo IdeaPad Miix 10 computer:
• “General safety” on page 2
• “Electrical safety” on page 3
• “Safety inspection guide” on page 5
• “Handling devices that are sensitive to electrostatic discharge” on page 6
• “Grounding requirements” on page 6
• “Safety notices: multilingual translations” on page 7
• “Laser compliance statement” on page 14
1
IdeaPad Miix 10 Hardware Maintenance Manual
General safety
Follow these rules below to ensure general safety:
• Observe a good housekeeping in the area where the machines are put
during and after the maintenance.
• When lifting any heavy object:
1. Make sure that you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt
to lift it.
4. Lift it by standing or pushing up with your leg muscles; this action could
avoid the strain from the muscles in your back. Do not attempt to lift any
object that weighs more than 16 kg (35 lb) or that you think is too heavy
for you.
• Do not perform any action that causes hazards to the customer, or that
makes the machine unsafe.
• Before you start the machine, make sure that other service representatives
and the customer are not in a hazardous position.
• Place removed covers and other parts in a safe place, keeping them away
from all personnel, while you are servicing the machine.
• Keep your toolcase away from walk areas so that other people will not trip it
over.
• Do not wear loose clothing that can be trapped in the moving parts of the
machine. Make sure that your sleeves are fastened or rolled up above your
elbows. If your hair is long, fasten it.
• Insert the ends of your necktie or scarf inside clothing or fasten it with the
nonconductive clip, about 8 centimeters (3 inches) from the end.
• Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for
your clothing.
Attention: Metal objects are good electrical conductors.
• Wear safety glasses when you are hammering, drilling, soldering, cutting
wire, attaching springs, using solvents, or working in any other conditions
that may be hazardous to your eyes.
• After service, reinstall all safety shields, guards, labels, and ground wires.
Replace any safety device that is worn or defective.
• Reinstall all covers correctly before returning the machine to the customer.
• Fan louvers on the machine help to prevent the overheating of internal
components. Do not obstruct fan louvers or cover them with labels or
stickers.
2
Safety information
Electrical safety
Observe the following rules when working on electrical equipments.
Important:
Use only approved tools and test equipments. Some hand tools have handles
covered with a soft material that does not insulate you when working with live
electrical currents.
Many customers have rubber floor mats near their machines that contain small
conductive fibers to decrease electrostatic discharges. Do not use such kind of mat
to protect yourself from electrical shock.
• Find the room emergency power-off (EPO) switch, disconnecting the switch
or electrical outlet. If an electrical accident occurs, you can then operate the
switch or unplug the power cord quickly.
• Do not work alone under hazardous conditions or near the equipment that
has hazardous voltages.
• Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
• Before you start to work on the machine, unplug the power cord. If you
cannot unplug it, ask the customer to power-off the wall box that supplies
power to the machine, and to lock the wall box in the off position.
• If you need to work on a machine that has exposed electrical circuits,
observe the following precautions:
– Ensure that another person, familiar with the power-off controls, is near
you.
Attention: Another person must be there to switch off the power, if
necessary.
– Use only one hand when working with powered-on electrical equipment;
keep the other hand in your pocket or behind your back.
Attention: An electrical shock can occur only when there is a complete
circuit. By observing the above rule, you may prevent a current from
passing through your body.
– When using testers, set the controls correctly and use the approved
probe leads and accessories for that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate
you from grounds such as metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages;
instructions for these precautions are in the safety sections of maintenance
information. Be extremely careful when you measure the high voltages.
• Regularly inspect and maintain your electrical hand tools for safe operational
condition.
• Do not use worn or broken tools and testers.
• Never assume that power has been disconnected from a circuit. First, check
it to make sure that it has been powered off.
3
IdeaPad Miix 10 Hardware Maintenance Manual
• Always look carefully for possible hazards in your work area. Examples of
these hazards are moist floors, nongrounded power extension cables, power
surges, and missing safety grounds.
• Do not touch live electrical circuits with the reflective surface of a plastic
dental mirror. The surface is conductive; such touching can cause personal
injury and machine damage.
• Do not service the following parts with the power on when they are removed
from their normal operating places in a machine:
– Power supply units
–Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
• If an electrical accident occurs:
– Caution: do not become a victim yourself.
– Switch off the power.
– Send the victim to get medical aid.
4
Safety information
Safety inspection guide
The purpose of this inspection guide is to assist you in identifying potential
unsafe conditions. As each machine was designed and built, required safety
items were installed to protect users and service personnel from injury. This
guide addresses only those items. You should use good judgment to identify
potential safety hazards according to the attachment of non-Lenovo IdeaPad
features or options not covered by this inspection guide.
If any unsafe conditions are present, you must determine how serious the
apparent hazard could be and whether you can continue without first correcting
the problem.
Consider these conditions and the safety hazards they present:
• Electrical hazards, especially primary power (primary voltage on the frame
can cause serious or fatal electrical shock)
• Explosive hazards, such as a damaged CRT face or a bulging capacitor
• Mechanical hazards, such as loose or missing hardware
To determine whether there are any potential unsafe conditions, use the
following checklist at the beginning of every service task. Begin the checks with
the power off, and the power cord disconnected.
Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Turn off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure
third-wire ground continuity for 0.1 ohm or less between the external
ground pin and the frame ground.
b. The power cord should be the type specified in the parts list.
c. Insulation must not be frayed or worn.
4. Check for cracked or bulging batteries.
5. Remove the cover.
6. Check for any obvious non-Lenovo IdeaPad alterations. Use good judgment
as to the safety of any non-Lenovo IdeaPad alterations.
7. Check inside the unit for any obvious unsafe conditions, such as metal
filings, contamination, water or other liquids, or signs of fire or smoke
damage.
8. Check for worn, frayed, or pinched cables.
9. Check that the power-supply cover fasteners (screws or rivets) have not
been removed or tampered with.
5
IdeaPad Miix 10 Hardware Maintenance Manual
Handling devices that are sensitive to electrostatic discharge
Any computer part containing transistors or integrated circuits (ICs) should be
considered sensitive to electrostatic discharge (ESD). ESD damage can occur
when there is a difference in charge between objects. Protect against ESD
damage by equalizing the charge so that the machine, the part, the work mat,
and the person handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements
noted here.
2. Make sure that the ESD protective devices you use have been certified (ISO
9000) as fully effective.
When handling ESD-sensitive parts:
• Keep the parts in protective packages until they are inserted into the product.
• Avoid contact with other people.
• Wear a grounded wrist strap against your skin to eliminate static on your
body.
• Prevent the part from touching your clothing. Most clothing is insulative and
retains a charge even when you are wearing a wrist strap.
• Use the black side of a grounded work mat to provide a static-free work
surface. The mat is especially useful when handling ESD-sensitive devices.
• Select a grounding system, such as those listed below, to provide protection
that meets the specific service requirement.
Note:
The use of a grounding system to guard against ESD damage is desirable but not
necessary.
– Attach the ESD ground clip to any frame ground, ground braid, or greenwire ground.
– When working on a double-insulated or battery-operated system, use an
ESD common ground or reference point. You can use coax or connectoroutside shells on these systems.
– Use the round ground prong of the ac plug on ac-operated computers.
Grounding requirements
Electrical grounding of the computer is required for operator safety and correct
system function. Proper grounding of the electrical outlet can be verified by a
certified electrician.
6
Safety information
Safety notices: multilingual translations
The safety notices in this section are provided in English, French, German,
Hebrew, Italian, Japanese, and Spanish.
Safety notice 1
Before the computer is powered on after FRU replacement, make sure all screws,
springs, and other small parts are in place and are not left loose inside the
computer. Verify this by shaking the computer and listening for rattling sounds.
Metallic parts or metal flakes can cause electrical shorts.
Avant de remettre l’ordinateur sous tension après remplacement d’une unité en
clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et
bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect
ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer
un court-circuit.
Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird,
muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile
fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf
Klappergeräusche geprüft werden. Metallteile oder-splitter können Kurzschlüsse
erzeugen.
Prima di accendere l’elaboratore dopo che é stata effettuata la sostituzione di una
FRU, accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni
siano nella corretta posizione e non siano sparse all’interno dell’elaboratore.
Verificare ciò scuotendo l’elaboratore e prestando attenzione ad eventuali rumori;
eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi.
Antes de encender el sistema despues de sustituir una FRU, compruebe que
todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio
y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema
y escuchando los posibles ruidos que provocarían. Las piezas metálicas pueden
causar cortocircuitos eléctricos.
7
IdeaPad Miix 10 Hardware Maintenance Manual
Safety notice 2
DANGER
Some standby batteries contain a small amount of nickel and cadmium. Do not
disassemble a standby battery, recharge it, throw it into fire or water, or shortcircuit it. Dispose of the battery as required by local ordinances or regulations.
Use only the battery in the appropriate parts listing. Use of an incorrect battery can
result in ignition or explosion of the battery.
Certaines batteries de secours contiennent du nickel et du cadmium. Ne les
démontez pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau. Ne
les mettez pas en court-circuit. Pour les mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la pile de sauvegarde ou celle
de l’horloge temps réel, veillez à n’utiliser que les modèles cités dans la liste de
pièces détachées adéquate. Une batterie ou une pile inappropriée risque de prendre
feu ou d’exploser.
Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet,
kann geringe Mengen Nickel und Cadmium enthalten. Sie darf nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden.
Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim
Ersetzen der Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden,
der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu
Entzündung oder Explosion führen.
Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio.
Non smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle.
Smaltirle secondo la normativa in vigore (DPR 915/82, successive disposizioni e
disposizioni locali). Quando si sostituisce la batteria dell’RTC (real time clock) o
la batteria di supporto, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo
parti. L’impiego di una batteria non adatta potrebbe determinare l’incendio o
l’esplosione della batteria stessa.
Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio.
No las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite.
Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se
encuentren en la lista de piezas. La utilización de una batería no apropiada puede
provocar la ignición o explosión de la misma.
8
Safety information
Safety notice 3
DANGER
The battery pack contains small amounts of nickel. Do not disassemble it, throw
it into fire or water, or short-circuit it. Dispose of the battery pack as required by
local ordinances or regulations. Use only the battery in the appropriate parts listing
when replacing the battery pack. Use of an incorrect battery can result in ignition
or explosion of the battery.
La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.
Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous à la
réglementation en vigueur. Lorsque vous remplacez la batterie, veillez à n’utiliser
que les modèles cités dans la liste de pièces détachées adéquate. En effet, une
batterie inappropriée risque de prendre feu ou d’exploser.
Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt,
wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden.
Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim
Ersetzen der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste
aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder Explosion
führen.
La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel fuoco
o nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR
915/82, successive disposizioni e disposizioni locali). Quando si sostituisce la
batteria, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego
di una batteria non adatta potrebbe determinare l’incendio o l’esplosione della
batteria stessa.
Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni
recargue, ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como
dispone la normativa local. Utilice sólo baterías que se encuentren en la lista de
piezas al sustituir la batería. La utilización de una batería no apropiada puede
provocar la ignición o explosión de la misma.
9
IdeaPad Miix 10 Hardware Maintenance Manual
Safety notice 4
DANGER
The lithium battery can cause a fire, an explosion, or a severe burn. Do not
recharge it, remove its polarized connector, disassemble it, heat it above 100°C
(212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as
required by local ordinances or regulations. Use only the battery in the appropriate
parts listing. Use of an incorrect battery can result in ignition or explosion of the
battery.
La pile de sauvegarde contient du lithium. Elle présente des risques d’incendie,
d’explosion ou de brûlures graves. Ne la rechargez pas, ne retirez pas son
connecteur polarisé et ne la démontez pas. Ne l’exposez pas à une temperature
supérieure à 100°C, ne la faites pas brûler et n’en exposez pas le contenu à l’eau.
Mettez la pile au rebut conformément à la réglementation en vigueur. Une pile
inappropriée risque de prendre feu ou d’exploser.
Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden, explodieren
oder schwere Verbrennungen hervorrufen. Batterien dieses Typs dürfen nicht
aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt werden. Auch darf ihr
Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung
angebrachte Verbindungsstecker entfernt werden. Bei der Entsorgung die örtlichen
Bestimmungen für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien
des Typs verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher
Batterien kann zu Entzündung oder Explosion führen.
La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o
procurare gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato,
smontarla, riscaldarla ad una temperatura superiore ai 100 gradi centigradi,
incendiarla o gettarla in acqua. Smaltirla secondo la normativa in vigore (DPR
915/82, successive disposizioni e disposizioni locali). L’impiego di una batteria
non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa.
La batería de repuesto es una batería de litio y puede provocar incendios,
explosiones o quemaduras graves. No la recargue, ni quite el conector polarizado,
ni la desmonte, ni caliente por encima de los 100°C (212°F), ni la incinere ni
exponga el contenido de sus celdas al agua. Deséchela tal como dispone la
normativa local.
10
Safety information
Safety notice 5
If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your
hands, immediately wash the affected areas with water at least for 15 minutes.
Seek medical care if any symptoms caused by the fluid are present after washing.
Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les
yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au
moins quinze minutes. Consultez un médecin si des symptômes persistent après le
lavage.
Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung
die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm
besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird
oder der Computer auf den Boden fällt. Wenn der Bildschirm beschädigt ist und
die darin befindliche Flüssigkeit in Kontakt mit Haut und Augen gerät, sollten
die betroffenen Stellen mindestens 15 Minuten mit Wasser abgespült und bei
Beschwerden anschließend ein Arzt aufgesucht werden.
Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso contenuto
entrasse in contatto con gli occhi o le mani, lavare immediatamente le parti
interessate con acqua corrente per almeno 15 minuti; poi consultare un medico se i
sintomi dovessero permanere.
Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus
manos, lave inmediatamente las áreas afectadas con agua durante 15 minutos
como mínimo. Obtenga atención medica si se presenta algún síntoma del fluido
despues de lavarse.
11
IdeaPad Miix 10 Hardware Maintenance Manual
Safety notice 6
DANGER
To avoid shock, do not remove the plastic cover that protects the lower part of the
inverter card.
Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique
protégeant la partie inférieure de la carte d’alimentation.
Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der
Spannungswandlerplatine umgibt, nicht entfernen.
Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la
parte inferiore della scheda invertitore.
Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la
tarjeta invertida.
Safety notice 7
DANGER
Though the main batteries have low voltage, a shorted or grounded battery can
produce enough current to burn personnel or combustible materials.
Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la
mise à la masse d’une batterie peut produire suffisamment de courant pour brûler
des matériaux combustibles ou causer des brûlures corporelles graves.
Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei
Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien zu
entzünden oder Verletzungen bei Personen hervorzurufen.
Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in
corto circuito o a massa può fornire corrente sufficiente da bruciare materiali
combustibili o provocare ustioni ai tecnici di manutenzione.
Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada
o con contacto a tierra puede producir la corriente suficiente como para quemar
material combustible o provocar quemaduras en el personal.
12
Safety information
Safety notice 8
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from
electrical outlets, remove the battery pack, and then disconnect any interconnecting
cables.
Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension,
débranchez tous les cordons d’alimentation des socles de prise de courant, retirez
la batterie et déconnectez tous les cordons d’interface.
Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose gezogen,
der Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU
entfernt wird.
Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese
elettriche tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi
di interconnessione.
Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de
las tomas de corriente eléctrica, quite la batería y, a continuación, desconecte
cualquier cable de conexión entre dispositivos.
13
IdeaPad Miix 10 Hardware Maintenance Manual
Laser compliance statement
Some models of Lenovo IdeaPad computer are equipped from the factory with
an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such
devices are also sold separately as options. If one of these drives is installed,
it is certified in the U.S. to conform to the requirements of the Department of
Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR)
Subchapter J for Class 1 laser products. Elsewhere, the drive is certified to
conform to the requirements of the International Electrotechnical Commission
(IEC) 825 and CENELEC EN 60 825 for Class 1 laser products.
If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note
the following:
CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
O uso de controles, ajustes ou desempenho de procedimentos diferentes daqueles
aqui especificados pode resultar em perigosa exposição à radiação.
Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de
réglage et d’utilisation des commandes, ainsi que les procédures décrites.
Werden Steuer- und Einstellelemente anders als hier festgesetzt verwendet, kann
gefährliche Laserstrahlung auftreten.
L’utilizzo di controlli, regolazioni o l’esecuzione di procedure diverse da quelle
specificate possono provocare l’esposizione a.
El uso de controles o ajustes o la ejecución de procedimientos distintos de los aquí
especificados puede provocar la exposición a radiaciones peligrosas.
Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage
device could result in exposure to hazardous laser radiation. There are no
serviceable parts inside those drives. Do not open.
14
Safety information
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may
contain an embedded Class 3A or Class 3B laser diode. Note the following:
DANGER
Emits visible and invisible laser radiation when open. Do not stare into the beam,
do not view directly with optical instruments, and avoid direct exposure to the
beam.
Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe
diretamente por meio de instrumentos óticos e evite exposição direta com o feixe
de luz.
Rayonnement laser si carter ouvert. Évitez de fixer le faisceau, de le regarder
directement avec des instruments optiques, ou de vous exposer au rayon.
Laserstrahlung bei geöffnetem Gerät. Nicht direkt oder über optische Instrumente
in den Laserstrahl sehen und den Strahlungsbereich meiden.
Kinyitáskor lézersugár ! Ne nézzen bele se szabad szemmel, se optikai
eszközökkel. Kerülje a sugárnyalábbal való érintkezést!
Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non
guardarlo direttamente con strumenti ottici e evitare l’esposizione diretta al fascio.
Radiación láser al abrir. No mire fijamente ni examine con instrumental óptico el
haz de luz. Evite la exposición directa al haz.
15
IdeaPad Miix 10 Hardware Maintenance Manual
Important service information
This chapter presents the following important service information:
• “Strategy for replacing FRUs” on page 16
– “Important notice for replacing a system board” on page 17
• “Important information about replacing RoHS compliant FRUs” on page 18
Important:
BIOS and device driver fixes are customer-installable. The BIOS and device drivers
are posted on the customer support site:
http://support.lenovo.com.
Strategy for replacing FRUs
Before replacing parts:
Make sure that all software fixes, drivers, and BIOS downloads are installed
before replacing any FRUs listed in this manual.
After a system board is replaced, ensure that the latest BIOS is loaded to the
system board before completing the service action.
To download software fixes, drivers, and BIOS, follow the steps below:
1. Go to http://support.lenovo.com.
2. Enter a serial number or select a product or use Lenovo smart downloading.
3. Select the BIOS/Driver/Applications and download.
4. Follow the directions on the screen and install the necessary software.
16
Important service information
Use the following strategy to prevent unnecessary expense for replacing and
servicing FRUs:
• If you are instructed to replace an FRU, but the replacement does not solve
the problem, reinstall the original FRU before you continue.
• Some computers have both a processor board and a system board. If you
are instructed to replace either of them, and replacing one of them does not
solve the problem, reinstall that board, and then replace the other one.
• If an adapter or a device consists of more than one FRU, any of the FRUs
may be the cause of the error. Before replacing the adapter or device,
remove the FRUs one by one to see if the symptoms change. Replace only
the FRU that changed the symptoms.
Attention: The setup configuration on the computer you are servicing may
have been customized. Running Automatic Configuration may alter the
settings. Note the current configuration settings (using the View Configuration
option); then, when service has been completed, verify that those settings
remain in effect.
Important notice for replacing a system board
Some components mounted on a system board are very sensitive. Improper
handling can cause damage to those components, and may cause a system
malfunction.
Attention: When handling a system board:
• Do not drop the system board or apply any excessive force to it.
• Avoid rough handling of any kind.
• Avoid bending the system board and hard pushing to prevent cracking at
each BGA (Ball Grid Array) chipset.
17
IdeaPad Miix 10 Hardware Maintenance Manual
Important information about replacing RoHS compliant FRUs
RoHS, The Restriction of Hazardous Substances in Electrical and
Electronic Equipment Directive (2002/95/EC) is a European Union legal
requirement affecting the global electronics industry. RoHS requirements
must be implemented on Lenovo products placed on the market after
June 2006. Products on the market before June 2006 are not required to
have RoHS compliant parts. If the original FRU parts are non-compliant,
replacement parts can also be non-compliant. In all cases if the original
FRU parts are RoHS compliant, the replacement part must also be RoHS
compliant.
Note: RoHS and non-RoHS FRU part numbers with the same fit and function
are identified with unique FRU part numbers.
Lenovo plans to transit to RoHS compliance well before the implementation
date and expects its suppliers to be ready to support Lenovo’s requirements
and schedule in the EU. Products sold in 2005 and 2006 will contain some
RoHS compliant FRUs. The following statement pertains to these products and
any product Lenovo produces containing RoHS compliant FRUs.
RoHS compliant FRUs have unique FRU part numbers. Before or after the
RoHS implementation date, failed RoHS compliant parts must always be
replaced with RoHS compliant ones, so only the FRUs identified as compliant
in the system HMM or direct substitutions for those FRUs may be used.
Products marketed before June 2006
Products marketed after June 2006
Current or
original part
Replacement FRU Current or
original part
Non-RoHS
Can be Non-RoHS
Non-RoHS
Can be RoHS
Non-RoHS
Can sub to RoHS
RoHS
Must be RoHS
Must be RoHS
Replacement FRU
Must be RoHS
Note: A direct substitution is a part with a different FRU part number that is
automatically shipped by the distribution center at the time of the order.
18
General checkout
General checkout
This chapter presents the following information:
• “What to do first” on page 20
• “Power system checkout” on page 21
Before you go to the checkout, make sure to read the following important notes:
Important notes:
• Only certified trained personnel can service the computer.
• Before replacing any FRU, read the entire page on removing and replacing
FRUs.
• Carefully remove screws for reuse when replacing FRUs.
• Be extremely careful during such write operations as copying, saving, or
formatting. Drives in the computer that you are servicing sequence might
have been altered. If you select an incorrect drive, data or programs might be
overwritten.
• Replace an FRU only with another FRU of the correct model. When you
replace an FRU, make sure that the machine model and the FRU part number are
correct by referring to the FRU parts list.
• An FRU should not be replaced just because of a single, unreproducible failure.
Single failures can occur for a variety of reasons that have nothing to do with a
hardware defect, such as cosmic radiation, electrostatic discharge, or software
errors. Consider replacing an FRU only when a problem recurs. If you suspect that
an FRU is defective, clear the error logs and run the test again. If the error does
not recur, do not replace the FRU.
• Be careful not to replace a nondefective FRU.
19
IdeaPad Miix 10 Hardware Maintenance Manual
What to do first
When you do return an FRU, you must include the following information in the
parts exchange form or parts return form that you attach to it:
1. Name and phone number of servicer
2. Date of service
3. Date on which the machine failed
4. Date of purchase
5. Procedure index and page number in which the failing FRU was detected
6. Failing FRU name and part number
7. Machine type, model number, and serial number
8. Customer’s name and address
Note for warranty: During the warranty period, the customer may be
responsible for repair costs if the computer damage was caused by misuse,
accident, modification, unsuitable physical or operating environment, or
improper maintenance by the customer.
The following is a list of some common items that are not covered under
warranty and some symptoms that might indicate that the system was
subjected to stress beyond normal use.
Before checking problems with the computer, determine whether the damage is
covered under the warranty by referring to the following list:
The following are not covered under warranty:
• LCD panel cracked from the application of excessive force or from being
dropped
• Scratched (cosmetic) parts
• Distortion, deformation, or discoloration of the cosmetic parts
• Plastic parts, latches, pins, or connectors that have been cracked or broken
by excessive force
• Damage caused by liquid spilled into the system
• Damage caused by the improper insertion of a PC Card or the installation of
an incompatible card
• Improper disc insertion or use of an optical drive
• Diskette drive damage caused by pressure on the diskette drive cover,
foreign material in the drive, or the insertion of a diskette with multiple labels
• Damaged or bent diskette eject button
• Fuses blown by attachment of a nonsupported device
• Forgotten computer password (making the computer unusable)
• Sticky keys caused by spilling a liquid onto the keyboard
• Use of an incorrect AC adapter on laptop products
The following symptoms might indicate damage caused by nonwarranted
activities:
• Missing parts might be a symptom of unauthorized service or modification.
• If the spindle of a hard disk drive becomes noisy, it may have been subjected
to excessive force, or dropped.
20
General checkout
Power system checkout
To verify a symptom, follow the steps below:
1. Turn off the computer.
2. Connect the AC adapter.
3. Make sure that power is supplied when you turn on the computer.
4. Turn off the computer.
5. Disconnect the AC adapter.
6. Make sure that the battery pack supplies power when you turn on the
computer.
If you suspect a power problem, see the appropriate one of the following power
supply checkouts:
• “Checking the AC adapter” on page 21
• “Checking operational charging” on page 21
Checking the AC adapter
You are here because the computer fails only when the AC adapter is used.
• If the power-on indicator does not turn on, check the power cord of the AC
adapter for correct continuity and installation.
• If the computer does not charge during operation, go to “Checking
operational charging”.
To check the AC adapter, follow the steps below:
1. Unplug the AC adapter cable from the computer.
2. Measure the output voltage at the plug of the AC adapter cable. See the
following figure:
3LQ
9ROWDJH9'&
Note: Output voltage for the AC adapter pin No. 2 may differ from the one you
are servicing.
3. If the voltage is not correct, replace the AC adapter.
4. If the voltage is acceptable, do the following:
• Replace the system board.
• If the problem continues, go to “Lenovo IdeaPad Miix 10” on page 26.
Note: Noise from the AC adapter does not always indicate a defect.
Checking operational charging
To check whether the battery charges properly during operation, use a
discharged battery pack or a battery pack that has less than 50% of the total
power remaining when installed in the computer.
21
IdeaPad Miix 10 Hardware Maintenance Manual
Perform operational charging. If the battery status indicator or icon does not
light on, remove the battery pack and let it return to room temperature. Reinstall
the battery pack. If the charge indicator or icon is still off, replace the battery
pack.
If the charge indicator still does not light on, replace the system board. Then
reinstall the battery pack.
22
Related service information
Related service information
This chapter presents the following information:
• “Restoring the factory contents by using Recovery system” on page 23
• “Passwords” on page 24
• “Power management” on page 25
Restoring the factory contents by using Recovery system
Restore of factory default
The Lenovo IdeaPad Miix 10 computers come with pre-installed Recovery
system.In order to save application files and the initial backed up files of the
system, the hard disk in a Lenovo computer includes a hidden partition when it
is shipped. If you need to restore the system to the point of your first boot up,
just enter Lenovo Recovery system and run System Recovery. For details of
Recovery system, see the User Guide for Lenovo Recovery system.
Note: This will delete all the new data on the system partition (C drive), which
is not recoverable. Make sure to back up your critical data before you perform this
action.
23
IdeaPad Miix 10 Hardware Maintenance Manual
When you use the recovery discs to boot your computer, the system will enter
the user interface for system recovery automatically. Please follow the prompt
to insert the backup discs to complete the whole recovery process.
Note: The recovery process might take up to 2 hours.
Passwords
As many as two passwords may be needed for any Lenovo IdeaPad computer:
the power-on password (POP) and the supervisor password (SVP).
If any of these passwords has been set, a prompt for it appears on the screen
whenever the computer is turned on. The computer does not start until the
password is entered.
Exception: If only an SVP is installed, the password prompt does not appear
when the operating system is booted.
Power-on password
A power-on password (POP) protects the system from being powered on by
an unauthorized person. The password must be entered before an operating
system can be booted.
Supervisor password
A supervisor password (SVP) protects the system information stored in the
BIOS Setup Utility. The user must enter the SVP in order to get access to the
BIOS Setup Utility and change the system configuration.
Attention: If the SVP has been forgotten and cannot be made available to
the servicer, there is no service procedure to reset the password. The system
board must be replaced for a scheduled fee.
24
Related service information
Power management
Note: Power management modes are not supported for APM operating system.
To reduce power consumption, the computer has three power management
modes: screen blank, sleep (standby), and hibernation.
Screen blank mode
If the time set on the “Turn off monitor” timer in the operating system expires,
the LCD backlight turns off.
To end screen blank mode and resume normal operation, press any key.
Sleep (standby) mode
When the computer enters sleep (standby) mode, the following events occur in
addition to what occurs in screen blank mode:
• The LCD is powered off.
• The hard disk drive is powered off.
• The CPU stops.
To enter sleep (standby) mode, To put the computer to sleep, do one of the
following:
• Close the display panel.
• Press the power button.
• Open the Charms and then select Settings → Power → Sleep.
In certain circumstances, the computer goes into sleep (standby) mode
automatically:
• If a “suspend time” has been set on the timer, and the user does not do any
operation with the keyboard, the hard disk, the parallel connector, or the
diskette drive within that time.
• If the battery indicator is amber, indicating that the battery power is low.
To cause the computer to return from sleep (standby) mode and resume the
operation, do one of the following:
• Press the Fn key.
• Press the power button.
• Press the Windows button.
Also, in the following event, the computer automatically returns from sleep
(standby) mode and resumes the operation:
• The time set on the resume timer elapses.
Note: The computer does not accept any input immediately after it enters
sleep (standby) mode. Wait a few seconds before taking any action to reenter
operation mode.
25
IdeaPad Miix 10 Hardware Maintenance Manual
Lenovo IdeaPad Miix 10
This chapter presents the following product-specific service references and
product-specific parts information:
• “Specifications” on page 26
• “Function key combinations” on page 28
• “FRU replacement notices” on page 29
• “Removing and replacing an FRU” on page 30
• “Locations” on page 54
• “Parts list” on page 57
Specifications
The following table lists the specifications of the Lenovo IdeaPad Miix 10 :
Table 1. Specifications
Feature
Description
Processor
• Intel Clover Trail-W Duo 1.5Ghz
Display
Standard
memory
SSD
I/O port
• IPS 10.1” 1366 × 768
Audio
26
• 2GB LPDDR2
•
•
•
•
•
64 GB or 128 GB
Micro HDMI port × 1
Micro USB 2.0 port × 1
Micro SD card slot × 1
Combo audio jack × 1
Lenovo IdeaPad Miix 10
Table 1. Specifications (continued)
Feature
Description
Touch pad
Integrated
camera
Battery
AC adapter
Pre-installed
operating
system
• Multi-touch type
• 1.0 MP on front
• 2 cell 6800 mAh, Polymer
• 12 V, 18 W
• Win8
27
IdeaPad Miix 10 Hardware Maintenance Manual
Function key combinations
The following table shows the function of each combination of function key.
Table 2. Function keys
:
28
Mutes/unmutes the sound.
:
Decreases the volume level.
:
Increases the volume level.
:
Closes the currently active window.
:
Refreshes the desktop or the currently active window.
:
Displays the Settings charm.
:
Enables/disables Airplane mode.
:
Displays all currently active apps.
:
Turns on/off the backlight of the LCD screen.
:
Toggles the display between the computer and an external
device.
:
Decreases display brightness.
:
Increases display brightness.
Lenovo IdeaPad Miix 10
FRU replacement notices
This section presents notices related to removing and replacing parts. Read
this section carefully before replacing any FRU.
Screw notices
Loose screws can cause a reliability problem. In the Lenovo IdeaPad computer,
this problem is addressed with special nylon-coated screws that have the
following characteristics:
• They maintain tight connections.
• They do not easily come loose, even with shock or vibration.
• They are harder to tighten.
Do the following when you service this machine:
• Keep the screw kit in your tool bag.
• Carefully remove screws for reuse when replacing FRUs.
• Use a torque screwdriver if you have one.
Tighten screws as follows:
• Plastic to plastic
Turn an additional 90° after the screw head touches the surface of the
plastic part:
more than 90°
(Cross-section)
• Logic card to plastic
Turn an additional 180° after the screw head touches the surface of the
logic card:
more than 180°
(Cross-section)
• Torque driver
If you have a torque screwdriver , refer to the “Torque” column for each step.
• Make sure that you use the correct screws. If you have a torque screwdriver,
tighten all screws firmly to the torque shown in the table. Carefully remove
screws for reuse when replacing FRUs. Make sure that all screws are
tightened firmly.
• Ensure torque screwdrivers are calibrated correctly following country
specifications.
29
IdeaPad Miix 10 Hardware Maintenance Manual
Removing and replacing an FRU
This section presents exploded figures with the instructions to indicate how to
remove and replace the FRU. Make sure to observe the following general rules:
1. Do not attempt to service any computer unless you have been trained and
certified. An untrained person runs the risk of damaging parts.
2. Before replacing any FRU, review “FRU replacement notices” on page 29.
3. Begin by removing any FRUs that have to be removed before the failing
FRU. Any of such FRUs are listed at the top of the page. Remove them in
the order in which they are listed.
4. Follow the correct sequence in the steps to remove the FRU, as given in the
figures by the numbers in square callouts.
5. When turning a screw to replace an FRU, turn it in the direction as given by
the arrow in the figure.
6. When removing the FRU, move it in the direction as given by the arrow in
the figure.
7. To put the new FRU in place, reverse the removal procedures and follow
any of the notes that pertain to replacement. For information about
connecting and arranging internal cables, see “Locations” on page 54.
8. When replacing an FRU, use the correct screw as shown in the procedures.
DANGER
Before removing any FRU, turn off the computer, unplug all power cords from
electrical outlets, and then disconnect any of the interconnecting cables.
Attention: After replacing an FRU, do not turn on the computer until you have
made sure that all screws, springs, and other small parts are in place and none
are loose inside the computer. Verify this by shaking the computer gently and
listening for rattling sounds. Metallic parts or metal flakes can cause electrical
short circuits.
Attention: The system board is sensitive to, and can be damaged by,
electrostatic discharge. Before touching it, establish personal grounding by
touching a ground point with one hand or using an electrostatic discharge (ESD)
strap (P/N 6405959) to remove potential shock reasons.
30
Lenovo IdeaPad Miix 10
1010 LCD cover
Figure 1. Removal step of LCD cover
Turn the pad over, open the SIM card door 1, then remove one screw 2.
1
2
Remove the LCD cover in the direction shown by arrow 3.
3
Step
2
Screw (quantity)
Color
Torque
M1.4 × 2.3, Cover to Bezel (IO Door) (1)
Black
0.9+/-0.1kgf*cm
31
IdeaPad Miix 10 Hardware Maintenance Manual
1020 Battery pack
For access, remove this FRU:
• “1010 LCD cover” on page 31
DANGER
Only use the battery specified in the parts list for your computer. Any other battery
could ignite or explode.
Figure 2. Removal steps of battery pack
Disconnect the battery connector in the direction shown by arrow 1, then
remove the five screws 2.
2
2
2
1
Step
2
32
Screw (quantity)
Color
Torque
M1.6 × 2.5, Battery to Bezel (5)
Sliver
1.85+/-0.15kgf*cm
Lenovo IdeaPad Miix 10
Figure 2. Removal steps of battery pack (continued)
Remove the battery pack in the direction shown by arrow 3.
3
When installing: Make sure the battery pack connector is attached firmly.
33
IdeaPad Miix 10 Hardware Maintenance Manual
1030 3G card
For access, remove these FRU:
• “1010 LCD cover” on page 31
• “1020 Battery pack” on page 32
Figure 3. Removal steps of 3G card
Disconnect the two 3D card cables (blue, red) 1. Then remove the one screw 2.
2
1
In step 1, unplug the jacks by using the removal tool antenna RF connector
(P/N: 51078891), or pick up the connectors with your fingers and gently unplug
them in the direction shown by the arrows.
When installing:
• In models with a 3G card that has two antenna connectors, plug the blue
cable (1st) (MAIN) into the jack labeled 1, and the red cable (2nd) (AUX) into
the jack labeled 2 on the card.
34
Lenovo IdeaPad Miix 10
Figure 3. Removal steps of 3G card (continued)
Remove the 3G card in the direction shown by arrow 3.
3
Step
2
Screw (quantity)
Color
Torque
M1.6 × 1.8, NGFF to Bezel (1)
Black
1.85+/-0.15kgf*cm
35
IdeaPad Miix 10 Hardware Maintenance Manual
1040 Speakers
For access, remove these FRUs in order:
• “1010 LCD cover” on page 31
• “1020 Battery pack” on page 32
• “1030 3G card” on page 34
Figure 4. Removal steps of speakers
Unplug one speaker connector in the direction shown by arrow 1. Remove the
four screws 2.
2
2
1
Step
2
Screw (quantity)
Color
Torque
M1.6 × 2.5, Speaker to Bezel (4)
Sliver
1.85+/-0.15kgf*cm
When installing: Make sure the speaker connector is attached firmly.
36
Lenovo IdeaPad Miix 10
Figure 4. Removal steps of speakers (continued)
Remove the speakers in the direction shown by arrows 3.
3
3
37
IdeaPad Miix 10 Hardware Maintenance Manual
1050 Audio Board
For access, remove these FRUs in order:
• “1010 LCD cover” on page 31
• “1020 Battery pack” on page 32
• “1030 3G card” on page 34
• “1040 Speakers” on page 36
Figure 5. Removal steps of audio board
Detach the two FPC connectors in the direction shown by arrows
Remove the one screw 3.
1 and 2.
3
1
2
Step
3
Screw (quantity)
Color
Torque
M1.6 × 2.5, Audio Board to Bezel (1)
Sliver
1.85+/-0.15kgf*cm
When installing: Make sure the FPC connectors are attached firmly.
38
Lenovo IdeaPad Miix 10
Figure 5. Removal steps of Audio Board (continued)
Remove the audio board in the direction shown by arrow 4.
4
When installing: Make sure the audio board connector is attached firmly.
39
IdeaPad Miix 10 Hardware Maintenance Manual
1060 Power board
For access, remove these FRUs in order:
• “1010 LCD cover” on page 31
• “1020 Battery pack” on page 32
• “1030 3G card” on page 34
• “1040 Speakers” on page 36
• “1050 Audio Board” on page 38
Figure 6. Removal steps of Power board
Detach the power board connector in the directions shown by arrows 1 and 2.
Remove the one screw 3.
3
1
2
40
Lenovo IdeaPad Miix 10
Figure 6. Removal steps of power board (continued)
Remove the power board 4.
4
Step
3
Screw (quantity)
Color
Torque
M1.6 × 2.5, PWR Board to Bezel (1)
Sliver
1.85+/-0.15kgf*cm
When installing: Make sure the power board connector is attached firmly.
41
IdeaPad Miix 10 Hardware Maintenance Manual
1070 Docking Board
For access, remove these FRUs in order:
• “1010 LCD cover” on page 31
• “1020 Battery pack” on page 32
• “1030 3G card” on page 34
• “1040 Speakers” on page 36
• “1050 Audio Board” on page 38
• “1060 Power board” on page 40
Figure 7. Removal steps of Docking Board
Detach the docking board connector in the directions shown by arrows 1 and
2 then remove the two screws 3.
3
1
2
Step
3
Screw (quantity)
Color
M1.6 × 2.5, Docking Board to Bezel (2)
Sliver
Torque
1.85+/-0.15kgf*cm
Remove the docking board in the directions shown by arrow 4.
4
When installing: Make sure the docking board connector is attached firmly.
42
Lenovo IdeaPad Miix 10
1080 Touch Pad Board
For access, remove these FRUs in order:
• “1010 LCD cover” on page 31
• “1020 Battery pack” on page 32
• “1030 3G card” on page 34
• “1040 Speakers” on page 36
• “1050 Audio Board” on page 38
• “1060 Power board” on page 40
• “1070 Docking Board” on page 42
Figure 8. Removal steps of touch pad board
Detach the touch pad board connector in the directions shown by arrows
and 2. Remove the two screws 3.
1
3
3
1
2
Step
3
Screw (quantity)
Color
M1.6 × 2.5, Touch Coltroller Board to Bezel (2)
Sliver
Torque
1.85+/-0.15kgf*cm
43
IdeaPad Miix 10 Hardware Maintenance Manual
Figure 9. Removal steps of touch pad board (continued)
Remove the touch pad board in the direction shown by arrow 4.
4
When installing: Make sure that the touch pad board connectors are attached firmly.
44
Lenovo IdeaPad Miix 10
1090 System board
Important notices for handling the system board:
When handling the system board, bear the following in mind.
• Be careful not to drop the system board on a bench top that has a hard surface,
such as metal, wood, or composite.
• Avoid rough handling of any kind.
• In the whole process, make sure not to drop or stack the system board.
• If you put a system board down, make sure to put it only on a padded surface such
as an ESD mat or conductive corrugated material.
For access, remove these FRUs in order:
• “1010 LCD cover” on page 31
• “1020 Battery pack” on page 32
• “1030 3G card” on page 34
• “1040 Speakers” on page 36
• “1050 Audio Board” on page 38
• “1060 Power board” on page 40
• “1070 Docking Board” on page 42
• “1080 Touch Pad Board” on page 43
45
IdeaPad Miix 10 Hardware Maintenance Manual
Figure 9. Removal steps of system board
Detach the camera board and LCD cable connectors shown by arrow 1 and
2. Unplug the vibrator board and DC-IN Cable connectors shown by arrow
3. Disconnect antenna GPS (gray) shown by arrow 4, then remove the three
screws 5 and three screws 6.
5
1
4
2
6
1
2
3
3
When installing: Make sure that all the connectors are attached firmly.
Step
5
6
46
Screw (quantity)
Color
Torque
M1.6 × 1.8, MB to Bezel (3)
Black
1.85+/-0.15kgf*cm
M1.6 × 2.5, MB to Bezel (3)
Sliver
1.85+/-0.15kgf*cm
Lenovo IdeaPad Miix 10
Figure 9. Removal steps of system board(continued)
Turn the system board over as shown by arrow 7 and unplug the WLAN card
board connector in the direction shown by arrow 8. Then remove the system
board as shown by arrow 9 and remove vibrator board 0 and DC-in board K.
7
8
9
10
10
47
IdeaPad Miix 10 Hardware Maintenance Manual
1100 PCI Express Mini Card for wireless LAN
For access, remove these FRUs in order:
• “1010 LCD cover” on page 31
• “1020 Battery pack” on page 32
• “1030 3G card” on page 34
• “1040 Speakers” on page 36
• “1050 Audio Board” on page 38
• “1060 Power board” on page 40
• “1070 Docking Board” on page 42
• “1080 Touch Pad Board” on page 43
• “1090 System board” on page 45
Figure 10. Removal steps of PCI Express Mini Card for wireless LAN
Disconnect the two wireless LAN cables (black, white) 1.
1
In step 1, unplug the jacks by using the removal tool antenna RF connector
(P/N: 08K7159), or pick up the connectors with your fingers and gently unplug
them in the direction shown by the arrows.
When installing:
• In models with a wireless LAN card that has two antenna connectors, plug
the black cable (1st) (MAIN) into the jack labeled 1, and the grey cable (2nd)
(AUX) into the jack labeled 2 on the card.
48
Lenovo IdeaPad Miix 10
Figure 10. Removal steps of PCI Express Mini Card for wireless LAN (continued)
Remove the card in the direction shown by arrow 2.
2
49
IdeaPad Miix 10 Hardware Maintenance Manual
1110 Integrated camera
For access, remove these FRUs in order:
• “1010 LCD cover” on page 31
• “1020 Battery pack” on page 32
• “1030 3G card” on page 34
• “1040 Speakers” on page 36
• “1050 Audio Board” on page 38
• “1060 Power board” on page 40
• “1070 Docking Board” on page 42
• “1100 PCI Express Mini Card for wireless LAN” on page 48
• “1080 Touch Pad Board” on page 43
• “1090 System board” on page 45
• “1100 PCI Express Mini Card for wireless LAN” on page 48
Figure 11. Removal steps of integrated camera
Remove the integrated camera in the direction shown by arrow 1.
1
50
Lenovo IdeaPad Miix 10
1120 Antenna Module
For access, remove these FRUs in order:
• “1010 LCD cover” on page 31
• “1020 Battery pack” on page 32
• “1030 3G card” on page 34
• “1040 Speakers” on page 36
• “1050 Audio Board” on page 38
• “1060 Power board” on page 40
• “1070 Docking Board” on page 42
• “1100 PCI Express Mini Card for wireless LAN” on page 48
• “1080 Touch Pad Board” on page 43
• “1090 System board” on page 45
• “1100 PCI Express Mini Card for wireless LAN” on page 48
• “1110 Integrated camera” on page 50
Figure 12. Removal steps of antenna module
Remove the WiFi antennas in the direction shown by arrow 1.
1
1
51
IdeaPad Miix 10 Hardware Maintenance Manual
Figure 12. Removal steps of antenna module(continued)
Remove the 3G antennas in the direction shown by arrow 2.
2
Remove the GPS antenna in the direction shown by arrow 3.
3
52
Lenovo IdeaPad Miix 10
Note: Applying labels to the base cover
The new base cover FRU is shipped with a kit containing labels of several
kinds. When you replace the base cover, you need to apply the following
label:
The following labels need to be peeled off from the old base cover, and
need to be put on the new base cover.
a
Rating label
b
Intel Label
c
GML Label
For the location of each label, refer to the following figure:
a
b
c
53
IdeaPad Miix 10 Hardware Maintenance Manual
Locations
Top view
1 Multi-touch screen
2 Integrated camera
3 Windows button
1
2
3
54
Lenovo IdeaPad Miix 10
Locations
Front view
1 Combo audio jack
2 Power button
1
2
55
IdeaPad Miix 10 Hardware Maintenance Manual
Bottom view, Left-side and Rear view
1 AC power adapter jack
2 Micro HDMI port
3 SIM card slot (on select models)
4 Micro SD card slot
5 Volume button
6Speakers
7 Micro USB port
6
7
5
4
3
1
56
2
Lenovo IdeaPad Miix 10
Parts list
This section presents the following service parts:
• “Overall” on page 58
• “Keyboard” on page 60
• “Miscellaneous parts” on page 61
• “Screws” on page 62
• “AC adapters” on page 63
Notes:
• Each FRU is available for all types or models, unless specific types or models
are specified.
57
IdeaPad Miix 10 Hardware Maintenance Manual
Overall
1
a
2
3
5
6
4
7
b
8
10
9
11
12
14
13
c
15
16
17
58
Lenovo IdeaPad Miix 10
Table 3. Parts list—Overall (continued)
No.
FRU
FRU no.
a-c
1
2
3
4
5
5
5
5
6
7
8
9
10
11
12
13
13
14
14
15
15
16
16
17
17
See “Miscellaneous parts” on page 61.
VIXJ0 LCD Module
VIXJ0 Antenna Wifi
VIXJ0 Antenna 3G
VIXJ0 Antenna GPS
VIXJ0 MB W8P SSD-64G Wifi
VIXJ0 MB W8S SSD-64G Wifi
VIXJ0 MB W8P SSD-64G 3G
VIXJ0 MB W8S SSD-64G 3G
Azw BCM4330 BGN SDIO + UART BT无线网卡
VIXJ0 Power Board W/Cable
VIXJ0 DC-IN Cable
VIXJ0 Vibrator Board
VIXJ0 Camera 1.3M
VIXJ0 Speaker
VIXJ0 Docking Board W/Cable
Huawei MU736 WCDMA NGFF WOW WWAN
Huawei MU736 WCDMA NON-GPS NGFF
WWAN
Audio Board 3G W/Cable
VIXJ0 Audio Board Wifi W/Cable
OFO MCF-101-0878 GFF Na SY JF TSP
GIS TC101GFT01 GFF SL SY JF TSP
Jazz SP/A L12M 2P01 3.7V25Wh 2cell bty
Jazz SN L12N 2P01 3.75V25Wh 2cell bty
VIXJ0 LCD Cover White
VIXJ0 LCD Cover Silver
_
AC power adapter (see “AC adapters” on page 63).
90400149
90203082
90203083
90203084
90003391
90003393
90004026
90004027
20200050
90003379
90203085
90003382
90003381
90203077
90003380
20200465
20200521
90003377
90003378
73044827
73045273
121500183
121500184
90203075
90203076
CRU
ID.
N
*
59
IdeaPad Miix 10 Hardware Maintenance Manual
Keyboard
Table 4. Parts list—Keyboard (continued)
60
Language
P/N
French
Traditional Chinese
Belgian
English
German
Arabic
U.K. English
Slovenian
Turkish
Italian
Bulgarian
Swiss
Portuguese
Japanese
US international
Thai
Spanish
Indic
Greek
Latin
Dutch
Czech&Slovak
Canadian Bilingual (En+Fr)
Hebrew
Hungarian
Korean
Russian
Nordic
25213123
25213121
25213133
25213111
25213124
25213125
25213112
25213135
25213115
25213113
25213139
25213136
25213117
25213127
25213137
25213116
25213114
25213140
25213129
25213118
25213128
25213138
25213119
25213130
25213131
25213120
25213122
25213132
CRU ID.
N
Lenovo IdeaPad Miix 10
Miscellaneous parts
Table 5. Parts list—Miscellaneous parts
FRU
Cable miscellaneous parts:
• (a ) VIXJ0 LCD Cable WO/3G
• (a ) VIXJ0 LCD Cable W/3G
• (b ) VIXJ0 Camera Cable
• (c ) VIXJ0 Touch Panel Cable
Note: Italicized letters in parentheses are references to
the exploded view in “Overall” on page 58 .
P/N
90203079
90203080
90203078
90203081
CRU ID.
N
61
IdeaPad Miix 10 Hardware Maintenance Manual
Screws
Table 6. Parts list—Screws
62
FRU
P/N
VIXJ0 SCREW 1.4D 2.3L K 2.5D 0.6TNINL+A
90203086
VIXJ0 SCREW 1.6D 1.8L K 4.1D ZK NL+
90203087
VIXJ0 SCREW 1.6X2L(NL)
90203088
VIXJ0 SCREW 1.6D 2.5L K 3.0D NI NL+0.3T
90203089
CRU ID.
N
Lenovo IdeaPad Miix 10
AC adapters
Table 7. Parts list—Miscellaneous parts
FRU
P/N
Delta ADP-18FW AA 12V1.5A adapter
36200380
Delta ADP-18AW JC 12V1.5A adapter
36200387
Delta ADP-18AW BC 12V1.5A adapter
36200381
Delta ADP-18AW DC 12V1.5A adapter
36200383
Delta ADP-18AW HC 12V1.5A adapter
36200386
Delta ADP-18AW GC 12V1.5A adapter
36200385
Delta ADP-18AW CC 12V1.5A adapter
36200382
CRU ID.
*
63
IdeaPad Miix 10 Hardware Maintenance Manual
Notices
Lenovo may not offer the products, services, or features discussed in this
document in all countries. Consult your local Lenovo representative for
information on the products and services currently available in your area. Any
reference to a Lenovo product, program, or service is not intended to state or
imply that only that Lenovo product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe
any Lenovo intellectual property right may be used instead. However, it is the
user’s responsibility to evaluate and verify the operation of any other product,
program, or service.
Lenovo may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you
any license to these patents.
L E N O V O G R O U P LT D . P R O V I D E S T H I S P U B L I C AT I O N “ A S I S ”
WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. Some jurisdictions do not allow disclaimer of express or implied
warranties in certain transactions, therefore, this statement may not apply to you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes
will be incorporated in new editions of the publication. Lenovo may make
improvements and/or changes in the product(s) and/or the program(s)
described in this publication at any time without notice.
The products described in this document are not intended for use in
implantation or other life support applications where malfunction may result in
injury or death to persons. The information contained in this document does not
affect or change Lenovo product specifications or warranties. Nothing in this
document shall operate as an express or implied license or indemnity under the
intellectual property rights of Lenovo or third parties. All information contained
in this document was obtained in specific environments and is presented as an
illustration. The result obtained in other operating environments may vary.
Lenovo may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.
Any references in this publication to non-Lenovo Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those
Web sites. The materials at those Web sites are not part of the materials for
this Lenovo product, and use of those Web sites is at your own risk.
64
Notices
Any performance data contained herein was determined in a controlled
environment. Therefore, the result obtained in other operating environments
may vary significantly. Some measurements may have been made on
development-level systems and there is no guarantee that these measurements
will be the same on generally available systems. Furthermore, some
measurements may have been estimated through extrapolation. Actual results
may vary. Users of this document should verify the applicable data for their
specific environment.
Trademarks
The following terms are either registered trademarks or trademarks of Lenovo
in the United States and/or other countries:
Lenovo®
Lenovo logo®
IdeaPad®
VeriFace®
OneKey Recovery®
APS®
Power Express®
Energy Management and ReadyComm®
The following terms are trademarks of Microsoft Corporation in the United
States, other countries, or both:
Windows®
Windows Vista®
Windows® 7
Windows® 8
The following are trademarks of Intel Corporation or its subsidiaries in the
United States, other countries, or both:
Intel®
Intel® Core™ 2 Duo
Other company, product, or service names may be the trademarks or service
marks of others.
65