LCD Display Monitor
MODEL
LM55S1 (W)
(B2224)
Português
Français
English
Deutsch
Español
Русский
Русский
中文繁體
中文繁體
Italiano
Português
Español
Français
Deutsch
Italiano
English
Features ............................................................................................................................................................................................... English-2
Important Information ............................................................................................................................................................................ English-3
Declaration ............................................................................................................................................................................................ English-5
Safety Precautions, Maintenance & Recommended Use ..................................................................................................................... English-6
Contents ............................................................................................................................................................................................... English-7
Parts Name and Functions .................................................................................................................................................................... English-8
Buttons, Switch, and Indicator............................................................................................................................................... English-8
Connectors and Terminals ..................................................................................................................................................... English-9
Wireless Remote Control (option) .......................................................................................................................................... English-10
Operating Range of Remote Control (option) ........................................................................................................................ English-11
Preparation for use ................................................................................................................................................................................ English-12
Flow of preparation ................................................................................................................................................................ English-12
[P-1] Preparation for installation ......................................................................................................................................................... English-13
Determine the installation location ......................................................................................................................................... English-13
Ventilation requirements for enclosure mounting .................................................................................................................. English-13
[P-2] Installing the monitor ................................................................................................................................................................. English-14
Using the wall mount or ceiling mount................................................................................................................................... English-14
Installing the wall mount bracket (option) .............................................................................................................................. English-14
Installing in the portrait position ............................................................................................................................................. English-15
Installing the optional frame kit .............................................................................................................................................. English-15
Installing the IR sensor (option) .............................................................................................................................................. English-15
[P-3] Installing the external speakers ................................................................................................................................................. English-16
[P-4] Connection procedure ............................................................................................................................................................... English-17
Wiring diagram ....................................................................................................................................................................... English-17
Prevention of disconnection of HDMI cable .......................................................................................................................... English-18
Connecting with a computer (analog connection) ................................................................................................................. English-19
Connecting with a computer (digital connection) .................................................................................................................. English-20
Connecting with a video device (component video/HDMI).................................................................................................... English-21
Connecting with a video device (composite video)/stereo amplifier ..................................................................................... English-22
[P-5] Installing the expansion module ................................................................................................................................................ English-23
Installation of the expansion module ..................................................................................................................................... English-23
SDI for long-distance connection or multiple-monitor connection ........................................................................................ English-23
Connecting OPS-compliant computer................................................................................................................................... English-24
[P-6] Connecting RS-232C/IR sensor ................................................................................................................................................ English-25
Connecting RS-232C/IR sensor............................................................................................................................................. English-25
[P-7] Connecting REMOTE ................................................................................................................................................................. English-25
Connecting REMOTE IN/OUT ................................................................................................................................................ English-25
[P-8] Connecting LAN......................................................................................................................................................................... English-26
Monitor connection using LAN .............................................................................................................................................. English-26
[P-9] Connecting the power cord (option) to the monitor .................................................................................................................. English-27
Connecting the power source ................................................................................................................................................ English-27
How to Use............................................................................................................................................................................................ English-28
Flow of How to Use................................................................................................................................................................ English-28
[U-1] Turning on all the connected devices ........................................................................................................................................ English-29
Turning on external devices ................................................................................................................................................... English-29
Turning on the monitor ........................................................................................................................................................... English-29
Power Management Function ................................................................................................................................................ English-30
[U-2] Selecting the video input ........................................................................................................................................................... English-31
[U-3] Controlling the external devices ................................................................................................................................................ English-32
[U-4] Selecting the OSD language ...................................................................................................................................................... English-32
[U-5] Auto-setup ................................................................................................................................................................................. English-33
[U-6] Selecting the picture mode ........................................................................................................................................................ English-34
[U-7] Screen adjustment ..................................................................................................................................................................... English-34
[U-8] Picture adjustment ..................................................................................................................................................................... English-35
[U-9] Speaker setting .......................................................................................................................................................................... English-35
[U-10] Volume, balance, and tone control ............................................................................................................................................ English-36
[U-11] Schedule setting ........................................................................................................................................................................ English-37
How to set up schedule ......................................................................................................................................................... English-38
[U-12] Remote control .......................................................................................................................................................................... English-39
RS-232C Remote control ....................................................................................................................................................... English-39
LAN Remote control............................................................................................................................................................... English-41
Configuration and basic operation of OSD screen ............................................................................................................................... English-42
Configuration of OSD screen ................................................................................................................................................. English-42
Basic operation of OSD ......................................................................................................................................................... English-43
OSD screen functions ........................................................................................................................................................................... English-44
Other functions ...................................................................................................................................................................................... English-54
Picture size ............................................................................................................................................................................. English-54
Picture mode .......................................................................................................................................................................... English-54
Control Lock mode ................................................................................................................................................................ English-54
OSD information..................................................................................................................................................................... English-54
Audio input change ................................................................................................................................................................ English-55
PIP, POP function .................................................................................................................................................................. English-56
Remote control numbering function ...................................................................................................................................... English-57
Troubleshooting .................................................................................................................................................................................... English-58
Specifications ........................................................................................................................................................................................ English-59
Pin Assignment ..................................................................................................................................................................................... English-60
English-1
English
Index
Features
Industry-use LED backlight adopted
LED backlight panel
Various Management Functions Supporting
Efficient Operation and Management
Page 59
Programmable Scheduling Function
Commercial grade panel adopting the LED backlight.
With the LED backlight, the monitor has achieved low power
consumption and eliminated mercury.
Pages 37, 38, and 51
High-quality LCD panel which provides a wide
variety of contents and messages clearly
Full HD panel
Page 59
The LM55S1 (W) panel reproduces images from video and
computer signals with precision and clarity, delivering full 1920
x 1080 high-definition resolution.
Enhanced Display Functionality for Various
Commercial Use/Support for System
Configuration Suitable for Diversified Applications
Tiling Capability with Frame compensation Page 53
Up to 25 panels (5 wide x 5 high) can be combined to create
a single large image (i.e., video wall) or other high-impact
signage. A frame compensation function is incorporated to
compensate the width of panel bezels so that images are
displayed with the utmost accuracy.
PIP, POP and Side-by-side
Pages 10, 48, and 56
Picture-In-Picture and Picture-Outside-Picture are available
when you want to display video content from a video input
source in the sub picture and display the PC input source in the
main picture, and vice versa.
The native resolution as high as 1920 x 1080 can display
these two input sources in the Side-by-side mode, ideal for
broadcasting and video-conferencing applications.
Digital Zoom
Page 46
Zoom mode for expanding 4:3 image to 16:9.
Various zoom modes are provided and it is possible to expand
4:3 aspect ratio images to 16:9. In addition, you can select the
dynamic display mode to display naturally widened images
with different zooming rates around the screen center and
screen edges. You can also optimally change the image size
diagonally, horizontally, and vertically.
Expansion slot allowing installation of expansion
modules according to applications
Option Slot
Page 23
You can mount an expansion module recommended by
Mitsubishi on the monitor. With such expansion module, you
can expand the functionality of the monitor according to the
purpose of use.
SDI Connection (option)
The monitor’s operating schedule can be programmed for
up to seven different scheduled time intervals by time, day
of the week and input port. This allows video content from
different inputs to be displayed on certain monitors within the
same installation according to the schedule, and extends the
monitor’s life and saves the power by turning it off during those
hours or days it is not in use.
Screen-saver Functions
Power-on Delay
The SDI BOX receives SD-SDI, HD-SDI, and 3G-SDI signals
at a maximum speed of 2.970 Gbit/s and displays them on the
monitor. A single image is distributed to multiple monitors that
are daisy-chained via SDI cables (BNC).
Page 53
For installations employing numerous monitors, the poweron delay function can power up the monitors sequentially with
delay between 2-50 seconds after the power is applied. Using
this function can prevent inrush current problems and reduce
the overall electrical load requirements when a single power
supply is used.
LAN Control
Pages 26, 41, and 50
You can efficiently and centrally control multiple monitors
for reconfiguration and remote diagnosis by sending control
commands from a computer via a LAN network. The user can
choose to use Mitsubishi protocol to control this monitor, or
other popular protocols including Crestron’s RoomViewTM and
AMX’s Device Discovery.
Others
DisplayPort
Pages 9 and 20
DisplayPort-compliant terminal is provided.
The monitor is equipped with a terminal supporting DisplayPort,
a digital interface standard. You can transmit video signals over
a single cable of max. 15-meters long.
Built-in Speakers
Pages 8 and 35
Speakers inside the display unit create stereo sounds and used
to communicate voice messages. You can connect external
speakers (commercially available) as needed.
Remote Control (option)
Page 23
Page 49
To reduce image persistence and maximize the panel life in
demanding signage applications, this product is equipped with
four screen-saver functions.
• GAMMA
• COOLING FAN
• BRIGHTNESS
• MOTION
Pages 10 and 11
Main operations and settings can be made on the remote
control (option). A remote control (option) is provided to control
the various functions of this monitor, including power on/off,
video source switching, and menu settings.
Closed Caption
Page 53
You can display captions.
When closed-caption is encoded with the video signal, the user
can select to display or hide the caption on screen.
This monitor is compliant with EIA-608-A.
Daisy Chain Connection (DVI-D)
Page 20
By connecting the DVI-D OUT connectors and the DVI-D IN
connectors using DVI-D cables (commercially available), you
can transmit video signals to up to 4 monitors (when using
2-meter cables). This function is useful in supplying a video
signal to multiple monitors.
English-2
Canadian Department of Communications Compliance Statement
DOC: This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2
No. 60950-1.
FCC Information
1. Use the attached specified cables with the LM55S1 (W) (B2224) color monitor so as not to interfere with radio and
television reception.
(1) Please use the supplied power cord or equivalent to ensure FCC compliance.
(2) Please use the supplied shielded video signal cable, 15-pin mini D-SUB to 15-pin mini D-SUB.
2. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
3. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment.
Windows is a registered trademark of Microsoft Corporation.
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing
LLC in the United States and other countries.
VESA, DisplayPort, and the DisplayPort icon are trademarks or registered trademarks of Video Electronics Standards
Association in the United States and other countries.
Intel is a trademark of Intel Corporation in the United States and other countries.
Crestron, Crestron RoomView and RoomView are trademarks or registered trademarks of Crestron Electronics, Inc. in the
United States and other countries.
AMX is a trademark or registered trademark of AMX, LLC in the United States and other countries.
Macintosh is a trademark of Apple Inc., registered in the U.S. and other countries.
All other brands and product names are trademarks or registered trademarks of their respective owners.
English-3
English
Important Information
Important Information (continued)
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S
POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL SOCKET. TO
FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET. DO
NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock.
Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been
included. Therefore, it should be read carefully in order to avoid any problems.
English-4
Declaration
We hereby certify that the color monitor LM55S1 (W) (B2224)
is in compliance with
Council Directive 2006/95/EC:
— EN 60950-1
Council Directive 2004/108/EC:
— EN 55022
— EN 61000-3-2
— EN 61000-3-3
— EN 55024
English
Declaration of the Manufacturer
and marked with
Mitsubishi Electric Corporation
2-7-3, Marunouchi,
Chiyoda-Ku
Tokyo 100-8310, Japan
Warning
This is a Class A product. In a domestic environment this product may cause radio interference, in which case the
user may be required to take adequate measures.
Declaration of the Manufacturer
Note: This symbol mark is for EU countries only.
This symbol mark is according to the directive 2002/96/EC Article 10 Information for users and
Annex IV.
Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of
separately from your household waste.
Please, dispose of this equipment at your local community waste collection/recycling centre.
In the European Union there are separate collection systems for used electrical and electronic product.
Please, help us to conserve the environment we live in!
The Production date
The production date is marked on the rating label of the display.
Please refer the coded serial number as following.
• Serial number (10 digit)
Digit
1
2
3
4
5
6
7
8
9
10
Serial number (Example)
3
Z
0
0
0
0
0
0
0
0
Example Date: Month / Year = Dec / 2013
•
Digit [1]: Year code of this production
Number
Year
•
3
4
5
2013
2014
2015
Digit [2]: Month code of production
Number
Month
1
2
3
4
5
6
7
8
9
X
Y
Z
Jan
Feb
Mar
Apr
May
Jun
Jul
Aug
Sep
Oct
Nov
Dec
English-5
Safety Precautions, Maintenance & Recommended Use
FOR OPTIMUM PERFORMANCE, PLEASE NOTE
THE FOLLOWING WHEN SETTING UP AND USING
THE LCD COLOR MONITOR:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
DO NOT REMOVE MONITOR BACK COVER. There are
no user serviceable parts inside and opening or removing
covers may expose you to dangerous shock hazards or
other risks.
Refer all servicing to qualified service personnel.
Do not spill any liquids into the cabinet or use your monitor
near water.
Do not insert objects of any kind into the cabinet slots,
as they may touch dangerous voltage points, which can
be harmful or fatal or may cause electric shock, fire or
equipment failure.
Do not place any heavy objects on the power cord.
Damage to the cord may cause shock or fire.
Do not place this product on a sloping or unstable cart,
stand or table, as the monitor may fall, causing serious
damage to the monitor.
A power supply cord is optional. To purchase it, please
contact your supplier.
For all other cases, use a power cord that matches the AC
voltage of the power outlet and has been approved by and
complies with the safety standard of your particular country.
If there is no wall outlet with ground terminal or earth
leakage circuit breaker, contact your dealer.
For installation work, be sure to ask a qualified technician.
- Insufficient installation strength may cause the LCD
monitor to topple over or drop off, resulting in injury.
- Improper handling may cause image quality degradation
or malfunction.
Do not place any objects onto the monitor and do not use
the monitor outdoors.
Do not bend power cord.
Do not use monitor in high temperature, humid, dusty, or
oily areas.
If monitor or glass is broken, do not come in contact with
the liquid crystal and handle with care.
If the LCD monitor is damaged and the liquid crystal leaks
out, do not inhale or swallow it.
Allow adequate ventilation around the monitor, so that heat
can properly dissipate. Do not block ventilated openings or
place the monitor near a radiator or other heat sources.
Do not put anything on top of the monitor.
The power cable connector is the primary means of
detaching the system from the power supply. The monitor
should be installed close to a power outlet, which is easily
accessible.
Handle with care when transporting. Save packaging for
transporting.
Please clean the holes of back cabinet to reject dirt and
dust at least once a year because of set reliability.
If using the cooling fan continuously, it’s recommended to
wipe holes a minimum of once a month.
CAUTION:
Immediately unplug your monitor from the wall outlet and refer
servicing to qualified service personnel under the following
conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled, or objects have fallen inside the
monitor.
• If the monitor has been exposed to rain or water.
• If the monitor has been dropped or the cabinet damaged.
• If the monitor does not operate normally by following
operating instructions.
Recommend Use
CAUTION:
• For optimum performance, allow 20 minutes for warm-up.
• Rest your eyes periodically by focusing on an object at least
5 feet away. Blink often.
• Position the monitor at a 90° angle to windows and other
light sources to minimize glare and reflections.
• Clean the LCD monitor surface with a lint-free, non-abrasive
cloth. Avoid using any cleaning solution or glass cleaner!
• Adjust the monitor’s brightness, contrast, and sharpness
controls to enhance readability.
• Avoid displaying fixed patterns on the monitor for long
periods of time to avoid image persistence (after image
effects).
• Get regular eye checkups.
Ergonomics
To realize the maximum ergonomic benefits, we recommend
the following:
• Use the preset Size and Position controls with standard
signals.
• Use the preset Color Setting.
• Use non-interlaced signals.
• Do not use primary color blue on a dark background, as
it is difficult to see and may produce eye fatigue due to
insufficient contrast.
English-6
Contents
LCD Display Monitor
MODEL
LM55S1 (W) (B2224)
† Utility disc (CD-ROM)
• User’s Manual
• Test image for Auto-setup
Refer to the USER’S MANUAL of the CD-ROM (accessory) for details.
Weitere Details finden Sie im BEDIENERHANDBUCH auf der CD-ROM (Zubehör).
Consulte el MANUAL DEL USUAIO del CD-ROM (accesorio) para obtener más información.
Consulte o MANUAL DO UTILIZADOR no CD-ROM (acessório) para mais informações.
Pour plus de détails, consultez le MANUEL DE L’UTILISATEUR figurant sur le CD-ROM (accessoire).
Consultare il MANUALE UTENTE del CD-ROM (accessorio) per i dettagli.
Для получения дополнительной информации см. РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ на CD-диске (принадлежность).
詳情請見收錄在安裝光碟(附件)內的使用說明書。
† Quick Start Guide
† LCD Monitor
† RS-232C connector
(D-SUB 9-pin) (4 m)
† Clamper x 7
(For preventing disconnection of the power
cord and HDMI cable, and for tying cables
of the wall mount bracket (option))
† Clamper x 2
(Wall mount brackets (option)
tying cables)
The following components are supplied as option.
• Power cord (North America): JC-PC3MA (AC100 - 120 V)
• Power cord (Europe): JC-PC3ME (AC200 - 240 V)
• Remote control kit
• Optional frame kit
• Wall mount bracket
• SDI BOX
*
English-7
For the use in the other regions, use a power cord that
matches the AC voltage of the power outlet and has been
approved by and complies with the safety standard of those
regions or countries.
English
Your LCD monitor (LM55S1 (W)) comes with the following:
Parts Name and Functions
Buttons, Switch, and Indicator
Left side
Front
Right side
Rear
Control buttons
ON
OFF
1 Main Power Switch
3 POWER button (
Switches the main power on/off.
Switches the power on/off.
This button doesn’t work when the power indicator is off. Turn
on the main power. (See page 29.)
)
NOTE:
Within 2 seconds after turning off the power by the POWER
button on the wireless remote control or the monitor or by a
communication command, don’t turn off the main power switch,
don’t disconnect the power cord, and don’t turn off the breaker.
If the AC power is turned off immediately after the power-off
operation, all the OSD settings including the language selection
may be reset to the factory defaults at the next power-on.
If the OSD settings are reset to the factory defaults as
described above, reconfigure the OSD settings using the
following procedure.
1. Turn off the power of the monitor using the wireless remote
control or otherwise.
2. Wait for at least 2 seconds.
3. Turn on the power of the monitor using the wireless remote
control or otherwise.
4. Check and reconfigure the OSD settings.
Displays the OSD menu to switch the video input.
You can select [HDMI], [DVI-D], [D-SUB], [OPTION]*,
[DISPLAYPORT], [YPbPr], or [VIDEO] using the UP ( ) or
DOWN ( ) button.
* OPTION can be used when an expansion module is
mounted on the option slot.
2 Remote control sensor and Power indicator
Acts as (-) button to decrease the adjustment in the OSD menu.
Decreases the audio output level when the OSD menu is off.
Remote control sensor: Receives the signal from the wireless
remote control.
Power indicator:
Indicates the state of the LCD monitor.
• Steady green:
The power is on.
• Steady red:
The power is off.
Some operations such as power-on
are possible.
• Steady green and red: The LCD monitor is in the sleep
mode.
• Off:
The main power is off.
• Steady red and blinking green: The LCD monitor is in the
schedule standby mode.
• Blinking red:
The LCD monitor has an error
(detected by the self-diagnostic
function).
4 MUTE button
Switches the audio mute on/off.
5 INPUT button
6 PLUS (+) button
Acts as (+) button to increase the adjustment in the OSD menu.
Increases the audio output level when the OSD menu is off.
7 MINUS (-) button
8 UP (
) button
Acts as button to move the highlighted area up to select an
adjustment item in the OSD menu.
9 DOWN (
) button
Acts as button to move the highlighted area down to select
an adjustment item in the OSD menu.
10 EXIT button
Activates the OSD menu when the OSD menu is off.
Acts as EXIT button to go back to the previous OSD menu.
11 Speakers
Audio sound is output from the built-in speakers.
(Reference) Control Lock mode
You can lock the operation buttons. See page 54.
NOTE:
For details about the OSD menu operation using the buttons, see “Basic operation of OSD.” (See page 43.)
English-8
Parts Name and Functions (continued)
Rear
Left side
Main Power Switch
Anti-theft lock slot
You can insert a
Kensington anti-theft
lock key.
IN OUT IN
OUT
Pr Pb Y
1 AC IN (3-pin, with earth terminal)
9 D-SUB IN
Connects with the supplied power cord.
Connects with the analog video output of a computer, etc.
2 REMOTE connector
10 AUDIO IN
IN connector:
Connects with the IR sensor supplied with the remote control
kit (option). The light sensing position can be moved within the
length of the IR sensor cable. Or connects with the REMOTE
OUT connector of other connected LM55S1 (W).
OUT connector:
Connects with the REMOTE IN connector of other connected
LM55S1 (W).
Connects with the audio output connector of external
equipment such as a computer, VCR, and DVD player.
(a) AUDIO IN1: ø3.5 mm Stereo-mini jack connector
(b) AUDIO IN2: RCA connector
NOTE:
When the IR sensor supplied with the remote control kit (option)
is connected, the remote control sensor on the monitor does
not operate.
Do not configure a multi-connection using REMOTE IN/OUT
and RS-232C IN/OUT at the same time.
3 RS-232C connector (D-SUB 9-pin)
11 YPbPr/VIDEO IN
To use the component video output of video devices such as a
DVD player, connect to the YPbPr IN connector.
To use the composite video output of video devices such as a
camera, connect to the Y connector of YPbPr.
Switch the component signal [YPbPr] and composite signal
[VIDEO] by the monitor buttons or remote control (option).
12 Speaker switch
Switches the built-in speakers and external speakers
(commercially available).
13 AUDIO OUT
IN connector:
Connects with the RS-232C OUT connector of a computer or
other connected LM55S1 (W).
OUT connector:
Connects with the RS-232C IN connector of other connected
LM55S1 (W).
Outputs the signal that is supplied to the AUDIO IN connector
( 10 ). Even when HDMI or DISPLAYPORT is selected, the
selected audio is output from the AUDIO OUT connector.
Connects with an external audio amplifier, etc.
NOTE:
Headphones and earphones aren’t supported.
4 LAN connector
Connects with a LAN cord.
14 EXTERNAL SPEAKER TERMINAL
5 HDMI IN
Connects with external speakers (commercially available).
15 Option slot
Connects with the digital video output of a computer, DVD
player, etc.
Insert an expansion module (option or commercially available)
in this slot.
6 DISPLAYPORT IN
Connects with the digital video output of a computer, etc.
7 DVI-D IN
Connects with the digital video output of a computer, etc.
8 DVI-D OUT
Outputs the signal that is supplied to the DVI-D IN connector ( 7 ).
CAUTION:
Damage to the product may result or monitor may not function
properly if an incompatible device is installed in this slot. See
page 23.
When mounting an OPS-compliant computer (commercially
available), turn on the cooling fan.
English-9
English
Connectors and Terminals
Parts Name and Functions (continued)
Wireless Remote Control (option)
Operate the LCD monitor by the remote control (option).
8 AUDIO INPUT buttons
Selects the audio input according to the video input.
9 PIP (Picture-In-Picture) buttons
ON/OFF button:
INPUT button:
Switches the PIP or POP mode on/off.
Selects video to be displayed in the sub
picture.
CHANGE button: Changes the main picture with the sub
picture.
[Description]
PIP: Picture-In-Picture
The sub picture is displayed within the main picture.
POP: Picture-Outside-Picture
The sub picture is displayed to the bottom right of the main
picture.
SBS: Side-By-Side
The main picture and the sub picture are displayed side by
side.
NOTE:
When the screen size is [CUSTOM] or [REAL], the PIP and POP
modes don’t work.
1 POWER button
10 STILL button
Switches the power on/off.
* When the Power indicator is not glowing, no controls will
work.
ON/OFF button:
Switches the still picture mode on/off.
CAPTURE button: Captures the new picture.
2 INPUT buttons
Selects the picture size from [FULL], [NORMAL], [CUSTOM],
[DYNAMIC], and [REAL]. See page 54.
11 SIZE button
Select the input signal from [HDMI], [DVI-D], [D-SUB], [OPTION]*,
[DISPLAYPORT], [YPbPr], and [VIDEO].
* OPTION can be used when an expansion module is
mounted on the option slot.
NOTE:
The [BNC] and [S-VIDEO] buttons don’t work.
12 MENU button
Switches the OSD menu mode on/off.
13 UP button (
)
Acts as button to move the highlighted area up to select
an adjustment item in the OSD menu. When the PIP MODE is
active, this button moves the sub picture up.
3 PICTURE MODE button
Selects the picture mode from [HIGHBRIGHT], [STANDARD],
[sRGB], and [CINEMA]. See page 34.
HIGHBRIGHT: The brightness is maximized.
STANDARD:
Factory default setting.
sRGB:
Suitable for color matching with sRGBcompliant devices.
CINEMA:
Suitable for viewing movies.
14 PLUS button (+)
Acts as (+) button to increase the adjustment in the OSD menu.
When the PIP MODE is active, this button moves the sub
picture to the right.
15 EXIT button
Displays the previous OSD menu.
16 DOWN button (
4 DISPLAY button
Displays the screen information. See page 54. When the remote
control mode is LOCK, you can set it back to NORMAL by
holding down the DISPLAY button for at least 8 seconds (see
page 53).
)
Acts as button to move the highlighted area down to select
an adjustment item in the OSD menu. When the PIP MODE is
active, this button moves the sub picture down.
17 MUTE button
Switches the mute function on/off.
5 SET button
Accepts the settings made in the OSD menu.
18 VOLUME buttons (VOL)
6 MINUS button (-)
Pressing the plus (+) side increases the audio output level.
Pressing the minus (-) side decreases the audio output level.
Acts as (-) button to decrease the adjustment in the OSD menu.
When the PIP MODE is active, this button moves the sub
picture to the left.
7 AUTO SETUP button
Displays the auto setup menu. See pages 33 and 49.
English-10
Operating Range of Remote Control
(option)
Bring the remote control (option) close to the remote control
sensor which is located at the bottom of the LCD monitor.
Use the remote control (option) within approximately 0.5 m from
the bottom of the monitor front and within approximately 0.5 m
at 15 degrees on the left and right of the monitor.
If the remote control (option) is not working properly, connect
the IR sensor cable supplied with the remote control kit (option)
to the REMOTE IN connector, and install and use the IR sensor
unit at a location where the remote control (option) works well.
English-11
English
Parts Name and Functions (continued)
Preparation for use
Flow of preparation
P-1
Preparation for installation
- Determine the installation location
- Ventilation requirements for enclosure mounting
Page 13
Carry out as necessary
P-2
Installing the monitor
- Using the wall mount or ceiling mount
- Installing the wall mount bracket (option)
- Installing in the portrait position
- Installing the optional frame kit
- Installing the IR sensor (option)
Pages 14 to 15
Carry out as necessary
P-3
P-4
Installing the external speakers (commercially available)
Connection procedure
- Wiring diagram
- Prevention of disconnection of HDMI cable
- Connecting with a computer (analog connection)
- Connecting with a computer (digital connection)
- Connecting with a video device (component video/HDMI)
- Connecting with a video device (composite video)/stereo amplifier
Page 16
Pages 17 to 22
Carry out as necessary
P-5
Installing the expansion module
- Installation of the expansion module
- SDI for long-distance connection or multiple-monitor connection
- Connecting OPS-compliant computer
Pages 23 to 24
Carry out as necessary
P-6
Connecting RS-232C/IR sensor
- Connecting RS-232C/IR sensor
Page 25
Carry out as necessary
P-7
Connecting REMOTE
- Connecting REMOTE IN/OUT
Page 25
Carry out as necessary
P-8
P-9
Connecting LAN
- Monitor connection using LAN
Connecting the power cord (option) to the monitor
- Connecting the power source
The monitor is ready for use.
How to Use
Page 28
English-12
Page 26
Page 27
Preparation for installation
Determine the installation location
CAUTION:
DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY
YOURSELF.
Installing your LCD monitor must be done by a qualified
technician. Contact your dealer for more information.
CAUTION:
MOVING OR INSTALLING THE LCD MONITOR MUST BE
DONE BY TWO OR MORE PEOPLE.
Failure to follow this warning may result in injury if the LCD
monitor falls.
CAUTION:
Proper operation of the monitor is not guaranteed when it is
mounted upside down, face up, or face down.
IMPORTANT:
Lay the protective sheet, which was wrapped around the LCD
monitor when it was packaged, beneath the LCD monitor so as
not to scratch the panel.
When you use this monitor in the multiple screen configurations,
you can install up to three monitors vertically in the landscape
position or up to one monitor vertically in the portrait position.
If you install four or more monitors vertically in the landscape
position or two or more monitors vertically in the portrait
position, set COOLING FUN to ON using the SCREEN SAVER
in the CONFIGURATION1 menu so that the temperature around
the monitors does not exceed the upper limit of the operating
temperature.
This LCD has a temperature sensor and cooling fan. If the LCD
becomes hot, the cooling fan will turn on automatically. If the
LCD becomes overheated, the “Caution” menu will appear. If
the “Caution” menu appears, stop using the monitor and allow
it to cool down. When the LCD monitor is used in an enclosure
or with protection on LCD surface, please check the inside
temperature of the monitor by “HEAT STATUS” (See page 53). If
the temperature is higher than the normal level, set “COOLING
FAN” to ON using the SCREEN SAVER function (See page 49).
When mounting an OPS-compliant computer (commercially
available), turn on the cooling fan.
Ventilation requirements for
enclosure mounting
To allow heat to disperse, leave space around the monitor as
shown in the figure below.
Wall
Don’t block these holes.
CAUTION:
Don’t block the holes in the rear of the monitor shown in the
figure above. If they are blocked, heat accumulates inside the
monitor, causing breakdown. The upper limit of the operationguaranteed ambient temperature when the monitor is installed
in the landscape position is 40˚C. When installing the monitor
in a case or an enclosure, ensure adequate ventilation to keep
the temperature inside the case 40˚C or lower by providing
a cooling fan or ventilation holes in the case. The upper limit
when the monitor is in the portrait position is 35˚C.
English-13
English
P-1
P-2
Installing the monitor
Using the wall mount or ceiling mount
Lay the screen face down
Lay the protective sheet on a table, which was wrapped around
the monitor when it was packaged, beneath the screen surface
so as not to scratch the screen surface.
Failure to follow the correct mounting procedures can result
in damage to the equipment or injury to the user or installer.
Product warranty does not cover damage caused by improper
installation.
Failure to follow these recommendations can void your
warranty.
For installation, use M6 iron screws (with a loose-proof spring
washer and having a length 10 mm longer than the thickness of
the mounting bracket) and tighten them securely. MITSUBISHI
ELECTRIC recommends using mounting interface that comply
with TÜV-GS and UL1678 standard in North America.
Carry out as necessary
About the metal bracket:
• Use a VESA-compliant metal bracket.
• Before installation, make sure that the installation surface
has sufficient strength.
• Use a metal bracket (commercially available) that is strong
enough to hold the monitor.
• Before installation, check the strength and other properties
to ensure the safety.
• Do not block the heat dissipating holes in the monitor with
the metal bracket. See page 13.
• For details of the mounting procedure and the safe
installation procedure, see the user instructions of the metal
bracket (commercially available) to be used.
• Take measures such as using multiple metal brackets,
holding the monitor at several points, and taking measures
to prevent falling or dropping in case of a problem in the
metal bracket or the installation location.
Table
607.6
607.6
400
343
Installing the wall mount bracket
(option)
343
400
When the wall mount brackets (option) are used, tiling in a
multi-screen configuration can be adjusted more easily.
(mm)
CAUTION:
Do not attempt to install the LCD monitor by yourself.
Consult your dealer for installation work.
Refer to User’s Manual of the wall mount bracket (option) for
the detailed installation procedure.
Protective Sheet
Handles
CAUTION:
For preventing the monitor from falling:
• Install the monitor with metal brackets for wall or
ceiling installation (commercially available) on your own
responsibility. For detailed procedures of installation, refer
to the instructions of the metal brackets.
• To avoid injury and damage resulting from fall of the monitor
in case of earthquake or other disaster, be sure to consult
the bracket manufacturer for installation location.
• To avoid failing the monitor down, thread commercially
available rope through 4 handles of the monitor and secure
the rope to the wall mount brackets or ceiling mount
brackets. Use rope that can bear a load
6 times the weight of the monitor (approximately 222 kg).
• Do not sleep where the monitor may topple over or fall in
case of an earthquake or other disaster.
• Use screws having enough strength to support the LCD
display monitor (made of steel etc.).
When the wall mount bracket (option) is installed, fix the wire
using the clamper (accessory).
NOTE:
Fix the wire of the wall mount bracket (option) to the rear of the
LCD monitor using the clamper (accessory) to prevent the wire
from being caught.
Wire
Clamper
(accessory)
English-14
Clamper
(accessory)
P-2
Installing the monitor (continued)
Carry out as necessary
Face-up
English
Installing in the portrait position
The monitor can be installed in the portrait position.
Ensure that the monitor is oriented as shown below.
CAUTION:
• The operating environmental condition (temperature) when
the monitor is in the portrait position is 0˚C to 35˚C.
• Proper operation of the monitor is not guaranteed when it is
not mounted as shown below (upside down, face-up, face
down, etc.).
• When mounting an OPS-compliant computer (commercially
available), be sure to set COOLING FAN to ON using
SCREEN SAVER in the CONFIGURATION1 menu of the
OSD screen function. If it is set to AUTO, the life of the
computer may become shorter than that with it set to ON or
the computer may have trouble.
• In the portrait position, the lifetime of the backlight is
shorter than that in the landscape position.
Face-down
Operation environment for portrait installation
When the monitor is installed in the portrait position, the
following conditions should be satisfied.
Temperature 0 - 35°C / 32 - 95°F
Humidity
20 - 80% (without condensation)
Installation in the portrait position
Turn the LCD monitor 90 degrees clockwise so that the
terminals are located on the left side as illustrated below.
NOTE:
This monitor doesn’t have a function to rotate displayed
images. To display images in the portrait orientation, use
already rotated images.
Installing the optional frame kit
A special optional frame kit can be mounted on the bezel for
the LCD monitor.
Please refer to Quick Start Guide of the special optional frame
kit for the detailed installation procedure.
Landscape
Installing the IR sensor (option)
Clockwise
Portrait
Portrait
90°
The IR sensor supplied with the remote control kit (option) can
be connected to the monitor, and the light sensing position
can be moved for monitor operation within the length of the IR
sensor cable supplied with the remote control kit (option). See
page 11.
Use the remote control (option) within 7 m from the front of the
IR sensor unit of the IR sensor and within 3.5 m at 30 degrees
on the left and right of the IR sensor unit.
Terminals should be on the left side.
English-15
P-3
Installing the external speakers
Carry out as necessary
How to install the external speakers
1. Connect the speaker output connectors on the monitor and external speakers (commercially available) using speaker cables.
Insert the left speaker cable into the SPEAKER (S) terminal (L) on the monitor, and insert the right speaker cable into the
SPEAKER (S) terminal (R).
NOTE:
Match the polarity of the speaker cables and that of the terminals (+ (red)/- (black)).
Unmatched polarity may cause problems with audio output.
Specifications of the recommended speaker:
Rated input: 10 W
Impedance: 8 Ω (left), 8 Ω (right)
CAUTION:
Use speakers that meet the specifications. Otherwise, the monitor or the speakers may have trouble.
Right speaker
(commercially available)
Left speaker
(commercially available)
Red(+)
SPEAKER (S)(L)
To speaker terminal (L)
Black(-)
Black(-)
SPEAKER (S)(R)
To speaker terminal (R)
Red(+)
English-16
Connection procedure
Before making connections
• First turn off the power of all the connected equipment before making connections.
• Refer to the user manual of each piece of equipment.
NOTE:
Please use the audio cable without resistance when the audio output terminal of the audio device and PC is stereo mini-Jack.
When the audio cable with resistance is used, the audio level may be affected or no sound could be heard.
Wiring diagram
LCD monitor (front)
Personal computer
(DVI-D, HDMI, DISPLAYPORT)
LCD monitor
(first monitor)
Stereo amplifier
DVD player or HD disk
player (HDMI, BNC)
LCD monitor (second monitor)
External speakers
Personal computer
(Analog RGB)
English-17
English
P-4
P-4
Connection procedure (continued)
Prevention of disconnection of HDMI cable
For connecting an HDMI cable to the connector on the monitor, it is recommended to secure the cable using an accessory clamper
to prevent accidental disconnection.
1. Connect an HDMI cable to the connector on the monitor.
2. Secure the HDMI cable using a clamper
(accessory).
Clamper (accessory)
English-18
P-4
Connection procedure (continued)
Analog connection:
(1) Connect a signal cable (mini D-SUB 15-pin – mini D-SUB 15-pin) (commercially available) to the D-SUB IN connector.
(2) Select [D-SUB] using the INPUT button on the monitor or the D-SUB button on the wireless remote control.
Audio connection:
• Connect an audio cable (ø3.5-mm stereo mini) (commercially available) to the AUDIO IN1 connector.
Select [AUDIO IN1] using the AUDIO INPUT button on the wireless remote control.
NOTE:
• For details on using the AUDIO INPUT button, see “Audio input change.”
Personal computer
(Analog RGB)
Signal cable
(mini D-SUB 15-pin – mini D-SUB 15-pin)
To D-SUB output
LCD monitor (rear)
D-SUB IN
Audio cable
(ø3.5-mm stereo mini)
To audio output
AUDIO IN1
The monitor automatically distinguishes the timings shown in the table below and sets the screen information. When a PC or other
device is connected, it automatically displays images properly. See the page describing AUTO SETUP/AUTO ADJUST.
<Factory preset timing>
Resolution
1
2
3
4
5
6
7
8
640 x 480
800 x 600
1024 x 768
1280 x 720
1280 x 768
1280 x 800
1360 x 768
1440 x 900
Frequency
Horizontal Vertical
31.5 kHz
60 Hz
37.9 kHz
60 Hz
48.4 kHz
60 Hz
45.0 kHz
60 Hz
47.8 kHz
60 Hz
49.7 kHz
60 Hz
47.7 kHz
60 Hz
55.9 kHz
60 Hz
Remarks
Resolution
9
10
11
12
13
14
15
1280 x 1024
1400 x 1050
1680 x 1050
1600 x 1200
1920 x 1080
1920 x 1080
1920 x 1200
Frequency
Remarks
Horizontal Vertical
64.0 kHz
60 Hz
65.3 kHz
60 Hz
64.7 kHz
60 Hz
75.0 kHz
60 Hz
56.2 kHz
50 Hz
67.5 kHz
60 Hz Recommend timing
74.0 kHz
60 Hz CVT Reduced Blanking
NOTE:
When a signal other than 1920 x 1080 is input, characters may be blurred and figures and objects may be distorted.
Images may not be displayed correctly depending on the video card or driver being used.
English-19
English
Connecting with a computer (analog connection)
P-4
Connection procedure (continued)
Connecting with a computer (digital connection)
Digital connection:
• Connection via the HDMI IN connector
(1) Connect an HDMI cable (commercially available) to the HDMI IN connector.
(2) Select [HDMI] using the INPUT button on the monitor or the HDMI button on the wireless remote control.
• Connection via the DVI-D IN connector
(1) Connect a DVI-D cable (commercially available) to the DVI-D IN connector.
(2) Select [DVI-D] using the INPUT button on the monitor or the DVI-D button on the wireless remote control.
• Connection via the DISPLAYPORT IN connector
(1) Connect a DisplayPort cable (commercially available) to the DISPLAYPORT IN connector.
(2) Select [DISPLAYPORT] using the INPUT button on the monitor or the DISPLAYPORT button on the wireless remote control.
Second monitor connection:
• Connect the DVI-D OUT connector on the first monitor and the DVI-D IN connector on the second monitor using a DVI-D cable
(commercially available).
NOTE:
• Connect the DVI-D IN and DVI-D OUT connectors correctly.
NOTE:
• In the daisy chain connection, you can connect up to 4 monitors (when using 2-meter cables). However, the maximum number
of connectable monitors may be limited. It is recommended to check the number of connectable monitors in advance in your
installation environment.
• Set RGB of POWER SAVE in the CONFIGURATION1 menu to OFF when using DVI-D in the daisy chain mode.
Audio connection:
• Connect an audio cable (ø3.5-mm stereo mini) (commercially available) to the AUDIO IN1 connector.
Select [AUDIO IN1] using the AUDIO INPUT button on the wireless remote control.
NOTE:
When an HDMI cable is connected, you can select HDMI audio.
When a DisplayPort cable is connected, you can select DISPLAYPORT audio.
• To output the audio to the second monitor, connect the AUDIO OUT connector on the first monitor and the AUDIO IN2 connector
on the second monitor using an audio cable (RCA) (commercially available).
Even when HDMI or DISPLAYPORT is selected on the first monitor, the selected audio is output from the AUDIO OUT connector.
NOTE:
• For details on using the AUDIO INPUT button, see “Audio input change.”
Personal computer
(DVI-D, HDMI)
LCD monitor
(first monitor)
To HDMI output
HDMI cable
HDMI IN
DisplayPort cable
DP IN
DVI-D cable
DVI-D IN
To DP output
To DVI-D output
Audio cable
(ø3.5-mm stereo mini)
To audio output
AUDIO IN1
LCD monitor (first monitor)
LCD monitor
(second monitor)
DVI-D OUT
DVI-D cable
LCD monitor (second monitor)
DVI-D IN
AUDIO OUT
AUDIO IN2
Audio cable (RCA)
English-20
P-4
Connection procedure (continued)
This LCD monitor can be connected with video devices such as a DVD player equipped with component video (YPbPr) output and a
DVD player equipped with HDMI output.
Refer to the user’s manual of the connected device for details. (Cables shown in the figure below are commercially available.)
• To connect a DVD player equipped with component output to the YPbPr IN connector on the monitor, use a BNC cable (BNC x 3
– BNC x 3) and a BNC – RCA adaptor (commercially available), or a signal cable (BNC x 3 – D connector).
Select [YPbPr] using the INPUT button on the monitor or the YPbPr button on the wireless remote control.
• To make audio connection, connect an audio cable (RCA) to the AUDIO IN2 connector.
Select [AUDIO IN2] using the AUDIO INPUT buttons on the wireless remote control.
• To connect a DVD player equipped with HDMI output to the HDMI IN connector on the monitor, use an HDMI cable.
Select [HDMI] using the INPUT button on the monitor or the HDMI button on the wireless remote control.
NOTE:
• When an HDMI cable is connected, you can select HDMI audio.
• For details on using the AUDIO INPUT button, see “Audio input change.”
LCD monitor
(side)
DVD player
(HDMI device)
HDMI cable
LCD monitor (rear)
To HDMI output
HDMI IN
To video output
BNC cable
(BNC x 3 to BNC x 3)
YPbPr IN
BNC – RCA adaptor
To D connector output
Signal cable
(BNC x 3 to D connector)
YPbPr IN
AUDIO IN2
To audio output
Audio cable (RCA)
English-21
DVD player
(component video device)
English
Connecting with a video device (component video/HDMI)
P-4
Connection procedure (continued)
Connecting with a video device (composite video)/stereo amplifier
This LCD monitor can be connected with video devices equipped with composite video output (VIDEO) or stereo amplifiers.
Refer to the user’s manual of the video device or the stereo amplifier for details. (Cables shown in the figure below are commercially
available.)
• When connecting the composite video output of the video device to the VIDEO IN connector (YPbPr Y connector) on the monitor,
use a BNC cable (commercially available). When the composite video output on the video device side is an RCA pin jack, jointly
use a BNC cable conversion adapter (commercially available) together with the RCA pin jack. For connection to the VIDEO IN
connector, select [VIDEO] using the INPUT button on the monitor or the VIDEO button on the wireless remote control.
For connection to the AUDIO IN1 or AUDIO IN2 connector on the monitor, use an audio cable (ø3.5-mm stereo mini RCA or
RCA). Connect the connectors of the audio cable (RCA) correctly.
Select [AUDIO IN1] or [AUDIO IN2] according to the connected connector by pressing the AUDIO INPUT button on the wireless
remote control.
• When connecting a stereo amplifier to the monitor, be sure to turn off the power of the stereo amplifier. For connection to the
AUDIO OUT connector on the monitor, use an audio cable (RCA). Connect the connectors of the audio cable (RCA) correctly. Be
sure to turn on the monitor first, and then turn on the stereo amplifier.
• The selected audio input signal is output from the AUDIO OUT connector.
LCD monitor (first monitor)
Audio cable (RCA)
To audio output
Video device
(composite video/video device)
Audio cable
(ø3.5-mm stereo mini – RCA)
To audio output
BNC cable
To video output
AUDIO IN2
LCD monitor (rear)
AUDIO IN1
YPbPr IN: Y
Stereo amplifier
AUDIO OUT
Audio cable (RCA)
To audio input
External speakers
English-22
Installing the expansion module
Installation of the expansion module
Install the expansion module to the option slot of this monitor
following the precautions and procedures described in the
manual supplied with the module.
Carry out as necessary
3. Insert the SDI BOX (option) in the option slot and secure it
on the monitor using the 2 screws that you have removed in
step 2.
Option slot
SDI BOX (option)
Examples of supported expansion modules:
• SDI BOX (DP-1SDI-3G)
• OPS-compliant computer (commercially available)
Recommended computer (commercially available):
ARK-DS220F-MTSA1E of Advantech Co., Ltd.
ARK-DS262GQ-U5A1E of Advantech Co., Ltd.
CAUTION:
Pay careful attention to the position and orientation of the
SDI BOX and insert it as far as it will go. The device may be
damaged if installed in an incorrect position and orientation.
NOTE:
• Please contact module manufacturer for any compatibility
issues.
[Description]
Intel ® OPS (Open Pluggable Specification) is a standard
suggested by Intel Corporation regarding the interface between
the pluggable module mounted on monitors designed for digital
signage applications and the monitors.
Supported OPS features:
• DVI-D
• UART
• Digital audio
• Power control
• DDC
• Analog audio
NOTE:
When an expansion module is in the option slot, the monitor
doesn’t enter the sleep mode even when POWER SAVE in the
CONFIGURATION1 menu is set to ON. Even when other video
input is selected, the monitor doesn’t enter the sleep mode.
See pages 30 and 49.
2. Connection with SDI
There are two cases of connection.
1) Connection to one monitor
1. Connect the video device and the SDI BOX (option) using
an SDI cable (BNC) (commercially available).
NOTE:
A high-spec BNC cable capable of carrying SDI signal is called
SDI cable and distinguished from other BNC cables.
2) Connection to multiple monitors
1. After the connection made in 2-1) above, connect the
SDI OUT connector on the first SDI BOX and the SDI IN
connector on the second SDI BOX using a commercially
available SDI cable (BNC).
NOTE:
The usable cable length (when SDI BOX (DP-1SDI-3G) is
mounted) is as follows:
• When one SDI BOX is connected: 100 m (3G-SDI)*
* Based on the result of the actual measurement using
the recommended cable. (Recommended cable: 1694A
made by Belden)
SDI for long-distance connection
or multiple-monitor connection
1. Mounting the SDI BOX on the monitor
1. Turn off the main power switch of the monitor and
disconnect the power cord.
CAUTION:
Be sure to disconnect the power cord to prevent breakdown
and electric shock.
2. Unscrew 2 screws and remove the option cover.
Option cover
NOTE:
For the connection method and specifications of the SDI BOX,
see the catalog or operation manual of the SDI BOX.
Removal of the SDI BOX
Hold the handle on the SDI BOX for removal.
CAUTION:
Use the handle to extract the SDI BOX only. Pulling on the SDI
cable (BNC) or by other means may cause damage.
NOTE:
Retain the option cover you have removed because it is
replaced when the SDI BOX isn’t mounted.
English-23
English
P-5
P-5
Installing the expansion module (continued)
Connecting OPS-compliant computer
Operation of all types of OPS-compliant computers isn’t
guaranteed.
Recommended computer (commercially available):
ARK-DS220F-MTSA1E of Advantech Co., Ltd.
ARK-DS262GQ-U5A1E of Advantech Co., Ltd.
NOTE:
When an OPS-compliant computer (commercially available)
is mounted, set “COOLING FAN” to ON using the SCREEN
SAVER function. See page 49.
1. Mounting the OPS-compliant computer
on the monitor
1. Turn off the main power switch of the monitor and
disconnect the power cord.
CAUTION:
Be sure to disconnect the power cord to prevent breakdown
and electric shock.
2. Unscrew 2 screws and remove the option cover.
Option cover
NOTE:
Retain the option cover you have removed because it is
replaced when the OPS-compliant computer isn’t mounted.
3. Insert an OPS-compliant computer (commercially available)
in the option slot and secure it on the monitor using the 2
screws that you have removed in step 2.
Option slot
OPS-compliant computer
(commercially available)
CAUTION:
Pay careful attention to the position and orientation of the
OPS-compliant computer and insert it as far as it will go.
The device may be damaged if installed in an incorrect
position and orientation.
Removal of the OPS-compliant computer
Hold the handle on the OPS-compliant computer for removal.
CAUTION:
Extract the OPS-compliant computer by using the handle only.
Pulling on the cable or other means may cause damage.
English-24
Carry out as necessary
P-6
Connecting RS-232C/IR sensor
Carry out as necessary
To control this monitor from a computer via a communication, connect this monitor and the computer using an RS-232C cable
(accessory).
In addition, to operate this monitor using the wireless remote control (option), connect the IR sensor supplied with the remote control
kit (option) to this monitor.
By connecting multiple LM55S1 (W) monitors using RS-232C cables, you can control any one or all of LM55S1 (W) using the
computer or one wireless remote control (option).
How to connect
•
•
•
•
Turn off the main power switch of the computer and this monitor. If you make a connection while the power is on, it causes a
failure of the devices.
Connect the computer and this monitor using a reverse type RS-232C cable (accessory).
In addition, when you connect two or more monitors as shown in the illustration below, connect the RS-232C OUT connector
of the first monitor and the RS-232C IN connector of the second monitor using a reverse type RS-232C cable (accessory). By
repeating the connection in the similar way, you can connect monitors in a daisy chain configuration.
When you use the IR sensor supplied with the remote control kit (option), connect the IR sensor to the first LM55S1 (W).
NOTE:
•
Though you can connect up to 104 monitors, the maximum number of connectable monitors may be limited depending on the
installation environment.
Computer
(RS-232C connection)
LCD monitor (first monitor)
LCD monitor (second monitor)
Wireless remote
control (option)
RS-232C OUT
RS-232C
RS-232C OUT
IR sensor
supplied with the
remote control kit
(option)
REMOTE IN
RS-232C IN
RS-232C IN
RS-232C cable
RS-232C cable
NOTE:
When only the 25-pin serial port is equipped as the serial communication port on the computer, a conversion adapter (commercially
available) is necessary for the connection.
P-7
Connecting REMOTE
Carry out as necessary
Connecting REMOTE IN/OUT
REMOTE cables can be used when the multi-connection is not configured with RS-232C cables. By connecting multiple LM55S1 (W)
monitors using REMOTE cables (ø3.5-mm stereo mini audio cable) (commercially available), you can control all of LM55S1 (W)
monitors using one remote control (option).
CAUTION:
•
•
Do not configure a multi-connection using REMOTE IN/OUT and RS-232C IN/OUT at the same time. Failure to do so may cause
improper operation of the LCD monitor.
You cannot use the remote control numbering function if monitors are multi-connected using REMOTE IN/OUT.
How to connect
•
•
Turn off the main power switch of this LCD monitor. If you make a connection while the power is on, it causes a failure of the devices.
Connect REMOTE OUT on LM55S1 (W) and REMOTE IN on the subsequent LM55S1 (W) using a REMOTE cable (ø3.5-mm
stereo mini audio cable) (commercially available).
NOTE:
•
•
Though you can connect up to 104 monitors, the maximum number of connectable monitors may be limited depending on the
installation environment.
You cannot control the LCD monitors from a computer if they are multi-connected using REMOTE IN/OUT.
English-25
English
Connecting RS-232C/IR sensor
P-8
Connecting LAN
Carry out as necessary
Monitor connection using LAN
As shown in the illustration below, you can connect this monitor and a computer in network through a LAN hub. Connect the monitor
and the LAN hub using a straight type LAN cable (commercially available).
How to connect
•
•
•
•
Turn off the main power switch of the computer and this monitor. If you make a connection while the power is on, it causes a
failure of the devices.
Connect the computer and the LAN hub using a straight type LAN cable (commercially available).
Connect this monitor and the LAN hub using a straight type LAN cable (commercially available).
When you connect two or more monitors, you can connect the monitor and the LAN hub using a straight type LAN cable
(commercially available) as described above.
LCD monitor (rear)
Computer
(LAN connection)
LAN
LAN cable
LAN hub
LAN
LAN
LAN cable
LAN
NOTE:
• When you use a cross type LAN cable (commercially available), you can connect the monitor and the computer one-to-one
without using a LAN hub, however, the computer may not be supported. It is recommended to check the operation in advance.
• The image transfer function via the LAN isn’t supported. This monitor isn’t equipped with the host function for controlling other
devices.
English-26
P-9
Connecting the power cord (option) to the monitor
Before making connections
• Check that the main power switch is off.
•
CAUTION:
When an OPS-compliant computer is installed and the main power switch of the monitor is on, connecting the power source
may cause the computer to power on, causing damage or breakdown of the operation system and the hard disc.
The power outlet socket should be installed as near the equipment as possible and should be easily accessible.
NOTE:
Please refer to “Safety Precautions, Maintenance & Recommended Use” in this manual for proper selection of the AC power cord.
Use the clamper to prevent accidental disconnection of the power cord.
1. Insert the power connector of the power cord fully and firmly into the AC IN connector of the monitor.
2. Secure the power cord using the clamper (accessory).
Main power switch
3. Insert the power plug into the power outlet socket.
• Fully insert the prongs into the power outlet socket.
Loose connection may cause noise.
• Don’t plug and unplug the power cord repeatedly in
a short time of period.
Clamper (accessory)
Clamper (accessory)
Power cord (option) (For EU)
Power cord (option) (For North America)
English-27
English
Connecting the power source
How to Use
Flow of How to Use
U-1
Turning on all the connected devices
U-2
Selecting the video input
Page 31
U-3
Controlling the external devices
Page 32
U-4
Selecting the OSD language
Page 32
Pages 29 to 30
D-SUB only
U-5
Auto-setup
Page 33
U-6
Selecting the picture mode
Page 34
U-7
Screen adjustment
Page 34
U-8
Picture adjustment
Page 35
Carry out as necessary
U-9
Speaker setting
Page 35
U-10
Volume, balance, and tone control
Page 36
U-11
Schedule setting
Pages 37 to 38
U-12
Remote control
Pages 39 to 41
English-28
U-1
Turning on all the connected devices
English
Turning on external devices
1. Turn on the connected devices such as
the computer and DVD player.
Turning on the monitor
CAUTION:
When an OPS-compliant computer is installed as an expansion
module, the computer automatically turns on and starts as the
monitor is turned on.
Don’t turn off the monitor immediately after turning it on
because the computer may be in the startup process. Select
OPTION as the video input and wait for the operating system of
the computer to complete the startup process.
Power button
or
NOTE:
When the computer doesn’t start within a given period of time
(approx. 1 minute), “OPTION ERROR” and an error message
are displayed. See the user’s manual of your computer.
2. Turn on the Main Power Switch.
Power button
The power indicator turns on green and the monitor turns
on.
The control buttons on the rear, wireless remote control,
and schedule setting don’t work while the main power
switch is off (the power indicator is off).
When using them, check that the Main Power Switch is on
(the power indicator is on).
Remote control
sensor
Wireless remote
control (option)
NOTE:
•
The remote control sensor is located at the bottom of this
LCD monitor and is difficult to see from the front. Check the
location referring “Parts Name and Functions” on page 8.
If the remote control (option) is not working properly,
connect the IR sensor supplied with the remote control kit
(option).
•
Main power switch
3. When the power indicator glows
red, press the POWER button on the
monitor.
The power indicator turns green.
NOTE:
Within 2 seconds after turning off the power by the POWER
button on the wireless remote control (option) or the monitor or
by a communication command, don’t turn off the main power
switch, don’t disconnect the power cord, and don’t turn off
the breaker. If the AC power is turned off immediately after
the power-off operation, all the OSD settings including the
language selection may be reset to the factory defaults at the
next power-on.
If the OSD settings are reset to the factory defaults as
described above, reconfigure the OSD settings using the
following procedure.
1. Turn off the power of the monitor using the wireless
remote control (option) or otherwise.
2. Wait for at least 2 seconds.
3. Turn on the power of the monitor using the wireless
remote control (option) or otherwise.
4. Check and reconfigure the OSD settings.
English-29
U-1
Turning on all the connected devices (continued)
Power Management Function
This function reduces the power consumption of the monitor
when the keyboard or the mouse is not used for a fixed period
even though the power of the monitor is on.
While this function is working, the screen becomes dark and
the power indicator glows green and red.
This function is available only when a computer equipped
with the VESA-approved DPM Power Management function is
connected to the monitor.
When the POWER SAVE in the OSD menu is turned ON, the
power management function works.
RGB: When the sync signal of computer input (HDMI, DVI-D,
D-SUB, DISPLAYPORT) is terminated, the monitor will
be in the sleep mode in several seconds.
VIDEO: When the sync signal of video input (YPbPr or VIDEO)
is terminated, the monitor will be in the sleep mode in
approximately 10 minutes.
[Description]
DPM: Acronym for Display Power Management
NOTE:
•
•
The default power management settings (POWER SAVE) for
RGB and VIDEO are ON.
When an expansion module is in the option slot, the monitor
doesn’t enter the sleep mode even when POWER SAVE in
the CONFIGURATION1 menu is set to ON. Even when other
video input is selected, the monitor doesn’t enter the sleep
mode.
Power Indicator
Status
Power-on mode
LED
Green
Power-off mode
Red
Power Standby when
“SCHEDULE” is enable
Red On
Green Blinking
Sleep mode
Red, Green
The main power is off.
Diagnosis (Detecting failure)
Off
Red Blinking
* See troubleshooting on page 58.
English-30
U-2 Selecting the video input
„ Select using the INPUT buttons on the wireless remote control (option).
You can select the desired video input by pressing the corresponding INPUT button on the wireless remote control.
Selectable video inputs are [HDMI], [DVI-D], [D-SUB], [OPTION]*, [DISPLAYPORT], [YPbPr], and [VIDEO].
* OPTION can be used when an expansion module is mounted on the option slot.
„ Select using the INPUT button on the monitor.
When you press the INPUT button on the monitor, the video input OSD menu is displayed and you can select the video input
using the and buttons.
Selectable video inputs are [HDMI], [DVI-D], [D-SUB], [OPTION]*, [DISPLAYPORT], [YPbPr], and [VIDEO]. When you press the
INPUT button again, the selected video input is displayed.
* OPTION can be used when an expansion module is mounted on the option slot.
NOTE:
The selection you make doesn’t complete unless you press the INPUT button while the video input OSD menu is displayed. The
time during which the video input OSD menu is displayed is same as that of the INFORMATION OSD. See page 51.
HDMI
DVI-D
D-SUB
OPTION
DISPLAYPORT
YPbPr
VIDEO
INPUT button
Video input OSD menu
Select using the
buttons.
English-31
and
English
You can select the desired video input using the wireless remote control (option) or the INPUT button on the monitor.
U-3 Controlling the external devices
To control the connected external devices, display images on the monitor.
DVD player, etc.
Personal computer
U-4 Selecting the OSD language
Display the OSD menu by pressing the MENU button on the wireless remote control (option) or the EXIT button on the rear of the
monitor.
Using LANGUAGE in the CONFIGURATION1 menu of the OSD screen function, you can select the OSD language. See page 49.
English-32
U-5 Auto-setup
Press the AUTO SETUP button on the wireless remote control to directly display the AUTO SETUP menu of the OSD screen
function.
Alternatively, press the MENU button on the wireless remote control or the EXIT button on the rear of the monitor to display the OSD
screen, and then display the AUTO SETUP menu by selecting AUTO SETUP in the CONFIGURATION1 menu.
By pressing the SET button, you can automatically and properly adjust the screen size, horizontal/vertical position, clock, clock
phase, and input signal level.
NOTE:
•
•
The auto setup works on D-SUB only.
When performing AUTO SETUP, display the exclusive still image (test image for
Auto-setup) on the full screen of this monitor using the computer connected
via D-SUB (analog signal). The still image is contained on the utility disc
(accessory).
Test image for Auto-setup
AUTO SETUP menu screen
Displaying the
AUTO SETUP
menu directly
Displaying the
OSD menu
English-33
English
analog inputs only
U-6 Selecting the picture mode
Using the PICTURE MODE button on the wireless remote control, you can select the picture mode suitable for images to be
displayed.
HIGHBRIGHT:
STANDARD:
sRGB:
CINEMA:
The brightness is maximized.
Factory default setting.
Suitable for color matching with sRGB-compliant devices.
Suitable for viewing movies.
NOTE:
• “sRGB” can be selected for computer input (HDMI*, DVI-D, D-SUB, OPTION (OPScompliant computer), and DISPLAYPORT).
• “CINEMA” can be selected for video input (HDMI*, OPTION (SDI), YPbPr, and VIDEO).
*
U-7
Automatically selected depending on the input signal.
Screen adjustment
When images aren’t displayed properly even after the auto setup, adjust the screen settings.
Display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the monitor.
Using the SCREEN menu of the OSD screen function, you can adjust the horizontal/vertical position, clock, clock phase, zoom
mode, custom zoom, and horizontal/vertical resolutions to obtain proper screen condition.
NOTE:
The position adjustment works on D-SUB, YPbPr, and VIDEO only.
The clock adjustment and the resolution adjustment work on D-SUB only.
The zoom adjustment works on all video inputs.
English-34
Display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the monitor.
Using the PICTURE menu of the OSD screen function, you can adjust the picture settings such as the brightness, contrast, and
sharpness to obtain desired image quality.
U-9 Speaker setting
Carry out as necessary
You can select the built-in speakers or external speakers (commercially available).
Press the speaker switch on the rear of the monitor to select the speakers.
To select the built-in speakers (INTERNAL)
To select the external speakers (EXTERNAL)
Speaker switch
English-35
English
U-8 Picture adjustment
U-10 Volume, balance, and tone control
Carry out as necessary
Volume control
You can control the volume level using the VOL button on the wireless remote control.
Balance and tone adjustment
You can adjust the speaker balance, treble, and bass using the AUDIO menu of the OSD screen function.
For adjustment, display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear
of the monitor.
NOTE:
If no audio is output when an OPS-compliant computer is in use, check that the monitor is selected as the audio output source by
the operating system of the computer. For the selection method, see the help or the user’s manual of the operating system for the
computer or the driver for the audio device.
English-36
U-11 Schedule setting
Carry out as necessary
English
Display the OSD menu by pressing the MENU button on the wireless remote control or the EXIT button on the rear of the monitor.
Using SCHEDULE in the CONFIGURATION2 menu of the OSD screen function, you can program power-on/off and input selection.
English-37
U-11 Schedule setting (continued)
Carry out as necessary
How to set up schedule
Check box
Radio button
Program number selection
When the cursor is in any of the check boxes showing the program numbers 1 to 7 on the left side of the screen, press the UP (
or DOWN ( ) button to move the cursor up or down to select the program number you want to set.
To enable the selected program number, press the SET button to place a checkmark in the check box. To disable it, clear the
checkmark.
)
Schedule setting of each program
When the cursor is in any of the check boxes, pressing the PLUS (+) button moves the cursor into the white frame on the right.
When the cursor is at any of the items within the white frame, pressing the PLUS (+) button moves the cursor to the right, and MINUS (-)
button to the left.
You can set the power-on/off time and video input by pressing the UP ( ) or DOWN ( ) button. In addition, you can select or
deselect the radio buttons by pressing the SET button.
ON:
OFF:
INPUT:
EVERY DAY:
MON - SUN:
EVERY WEEK:
Set the time when the power is turned on. If you don’t want to set the power-on time, enter “--.”
Set the time when the power is turned off. If you don’t want to set to the power-off time, enter “--.”
Displays the video input selected when the power is turned on. If you want to select the video input that was
selected before the power is turned on, enter “--.” When you set the ON time and the video input, you can
switch the video input alone.
Select this option to execute the schedule every day. When you select EVERY DAY, you cannot select any days
of the week and EVERY WEEK.
Select the days of the week on which you want to execute the schedule. Unless you select EVERY WEEK, too,
the selection of the days of the week is cleared after the schedule is executed one time.
Select this option to execute the schedule on the selected days of the week, every week.
Schedule confirmation
To confirm the schedule, press the MENU button on the wireless remote control or the EXIT button on the rear of the monitor to exit
the SCHEDULE menu of the OSD screen function.
If you turn off the power before exiting the SCHEDULE menu, the schedule settings may be canceled.
NOTE:
• Before making the schedule settings, be sure to check the current date and time using “DATE AND TIME.”
• When you close the SCHEDULE screen, the settings are saved.
• When two or more schedules are enabled, they are executed in descending order of the program number, and the power is
turned off upon completion of the last executed schedule.
• When there are two or more schedules having the same power-on/off time, the one having the largest program number is
executed.
• You cannot set the power-on time and the power-off time to the same time.
• When OFF TIMER is ON, the schedule settings are ignored.
• When the main power switch or AC power supply turns off or the circuit breaker trips due to power failure or other causes, the
schedule programs you set aren’t executed.
English-38
U-12 Remote control
Carry out as necessary
When the monitor is connected directly to a computer using an RS-232C cable (accessory), the following operations can be
controlled via a communication. Select the communication interface (RS-232C) used for the serial communication function. (See
page 50.)
•
•
•
•
•
Power ON or OFF
Switching between input signals
Volume control and mute
Auto setup
Check of the internal temperature of the monitor, etc.
NOTE:
For connection with a 25-pin serial port connector on the computer, a conversion adapter (commercially available) is required.
1) Interface
PROTOCOL
RS-232C
BAUD RATE
9600 [bps]
DATA LENGTH
8 [bit]
PARITY BIT
NONE
STOP BIT
1 [bit]
FLOW CONTROL
NONE
•
For direct connection using RS-232C, use the RXD, TXD, and GND lines.
2) Control command diagram
The command is structured by the address code, function code, data code and end code. The length of the command is
different for each function.
NOTE:
• This example shows a basic command that is used when a single computer and a single monitor are connected.
When you want to connect multiple monitors or perform complicated control using other commands than the basic
commands, contact your dealer for advanced command specifications.
• To send commands with a keypad using terminal software, select “2s” or “30s” for CONTROL TIME OUT in
CONFIGURATION2 in the OSD menu. (Follow the same procedure for LAN control.)
Address code
Function code
Data code
End code
HEX
30h 30h
Function
Data
0Dh
ASCII
‘0’ ‘0’
Function
Data
[Address code]
[Function code]
[Data code]
[End code]
30h 30h (ASCII code, ‘0’ ‘0’), fixed.
Code unique to each control function.
Data unique to each control function (Not always indicated by numerical values.)
0Dh (ASCII code, ‘ ’) fixed.
3) Control sequence
(1) A command is sent from the computer to the monitor. (Commands should be sent at intervals of at least 600 ms.)
(2) The monitor sends a return command within 600 ms* after receiving the end code. If the monitor fails to receive the
command, it doesn’t send any return command. (*During the power-on/off or input selection process, the transmission of the
return command may take more than 600 ms.)
(3) The computer checks the return command to see whether the command it sent was received or not. The computer must
receive the return command before sending the next command.
(4) The monitor sends various codes other than commands including the return command. While RS-232C control sequence is
in progress, the computer must reject the codes.
Example: Turn the power ON (‘ ’ is for ASCII code)
Control command from
computer
Return command from
monitor to computer
30 30 21 0D
‘0’ ‘0’ ‘!’ ‘ ’
Description of command
Sending a command for
power-on
30 30 21 0D
‘0’ ‘0’ ‘!’ ‘ ’
Command received
(Command echoed back)
English-39
English
RS-232C Remote control
U-12 Remote control (continued)
Carry out as necessary
4) Operation commands
The operation commands configure the basic operation settings of this LCD monitor. The commands may not work during signal
switchover.
The operation commands have no data codes.
Operation
POWER ON
POWER OFF
ASCII
!
"
HEX
21h
22h
FORCE POWER OFF WITH OPS*
""
22h 22h
INPUT HDMI
_r1
5Fh 72h 31h
INPUT DVI-D
_r2
5Fh 72h 32h
INPUT D-SUB
_r3
5Fh 72h 33h
INPUT OPTION**
_r5
5Fh 72h 35h
INPUT DISPLAYPORT
_r6
5Fh 72h 36h
INPUT VIDEO
_v1
5Fh 76h 31h
INPUT YPbPr
_v2
5Fh 76h 32h
VOLUME UP
r06
72h 30h 36h
VOLUME DOWN
r07
72h 30h 37h
AUTO SETUP
r09
72h 30h 39h
AUDIO MUTE
ra6
72h 61h 36h
* Used when the OPS-compliant computer makes no response.
** OPTION can be used when an expansion module is mounted on the option slot.
•
•
•
•
•
•
After sending the POWER ON or POWER OFF command, wait for at least 20 seconds to send the next command.
After sending a command for video input selection, wait for at least 5 seconds to send the next command. Otherwise, the
monitor may not reply within 600 ms.
Set the timeout value of the control device on the host side to 30 seconds or longer.
In the power-off mode, only the POWER ON operation command and the power status acquisition commands described in
the next paragraph work.
In the sleep mode, only the POWER ON and POWER OFF operation commands and the power status acquisition commands
described in the next paragraph work.
• When no expansion module is mounted, the FORCE POWER OFF WITH OPS operation command is unavailable.
• When an expansion module is mounted, all the input connectors don’t enter the sleep mode.
After turning off the power using an operation command, wait for at least 2 seconds to turn off the AC power using the main
power switch or the breaker. Otherwise, the OSD settings may be reset to the factory defaults.
English-40
U-12 Remote control (continued)
5) Read command
The computer sends the command without data code to the monitor.
After receiving this command, the monitor returns the command with data code including the current status to the computer.
Example: When the computer asks the power status of the monitor, and the status of the monitor is powered-on.
Control command from computer
Return command from monitor to
computer
Description of command
Sending a command for checking the
power status
30 30 76 50 0D ‘0’‘0’‘v’‘P’[enter]
30 30 76 50 31 0D ‘0’‘0’‘v’‘P’‘1’[enter]
Monitor is powered-on.
Structure of the Read-command
Function
POWER
Input
Internal
temperature
ON
OFF (Sleep)
HDMI
DVI-D
D-SUB
OPTION*
DISPLAYPORT
VIDEO
YPbPr
Around the main
board
Around the power
supply
vP
vP
vI
vI
vI
vI
vI
vI
vI
Resolution
1˚C
Resolution
1˚C
ASCII
Data (Receive)
1
0
r1
r2
r3
r5
r6
v1
v2
Function
76 50
76 50
76 49
76 49
76 49
76 49
76 49
76 49
76 49
HEX
Data (Receive)
31
30
72 31
72 32
72 33
72 35
72 36
76 31
76 32
tc1
(ex.) +25
74 63 31
2B 20 32 35
tc2
(ex.) +31
74 63 32
2B 20 33 31
* OPTION can be used when an expansion module is mounted on the option slot.
NOTE:
The monitor will acknowledge the power-on/off command issued from the OPS-compliant computer, however, it will not execute
the command. This is not a malfunction. For automatic operation, use SCHEDULE in the CONFIGURATION2 menu of the OSD
screen function.
LAN Remote control
When you connect the monitor and the computer using a LAN hub and a LAN cable (see page 26) and then configure the network
settings using LAN SETTING in the CONFIGURATION2 menu of the OSD screen function, you can remote-control the monitor using
the same commands as those for RS-232C.
1. Setting procedure
(1) Select LAN as the communication interface used for the serial communication function. (See page 50.)
(2) Set the following network parameters using the OSD menu. (See page 50.)
• DHCP client ON/OFF, IP address, subnet mask and default gateway.
(3) Set the IP address described above and the port number (63007 or 3007) using the application program of your computer to
perform the socket communication.
(4) Send the same control command as that for RS-232C via TCP/IP socket communication.
(5) Check the return command sent from the monitor. When it is received successfully, the setting is completed.
English-41
English
Carry out as necessary
Configuration and basic operation of OSD screen
Configuration of OSD screen
This monitor is equipped with the OSD (On Screen Display) function for easy screen adjustment. The OSD function allows you to
control the menus displayed on the screen for brightness setting and other settings.
The OSD screen is configured as shown below.
Main Menu Screen
Main menu
Icons other than the one you selected are grayed out.
PICTURE
Page 44
CONFIGURATION1
Page 49
SCREEN
Page 46
CONFIGURATION2
Page 50
AUDIO
Page 47
ADVANCED OPTION
Page 52
PIP
Page 48
Sub menu (Adjustment items)
Adjustment items are displayed.
Adjustment status
The values adjusted by the wireless remote control and the
PLUS (+) and MINUS (-) buttons on the monitor are displayed.
Control button guide
Buttons for controlling the displayed OSD menu are displayed.
Sub menu screen
When you select a sub menu, an OSD screen is displayed.
Sub menus contain information screens, adjustment menu screens, and selection menu screens as shown below.
Sub menu screen: Picture reset (for example)
English-42
Configuration and basic operation of OSD screen (continued)
Check that the power indicator illuminates green and the monitor is powered on.
Step
Monitor button
Wireless remote control
OSD screen display
1
Press the MENU button to display the
/
OSD screen and then press the
button to select the main menu.
Press the EXIT button to display the
/
OSD screen and then press the
button to select the main menu.
When you press the SET button to
accept the selected main menu, the
sub menu at the top is selected.
When you press the INPUT button to
accept the selected main menu, the
sub menu at the top is selected.
2
3
Press the
menu.
/
button to select a sub
Press the
menu.
/
button to select a sub
4
Press the SET button to accept the
selected sub menu.
Press the INPUT button to accept the
selected sub menu.
/
button to select the
Press the
setting and then press the SET button
to accept it.
Press the
/
button to select the
setting and then press the INPUT
button to accept it.
5
The OSD screen disappears when you press the MENU button on the wireless remote control 1 time or the EXIT button on the
monitor 3 times after step 5.
NOTE:
Besides the example described above, some items are selected or adjusted by the PLUS (+) and MINUS (-) buttons.
Operate the buttons according to the control button guide displayed at the bottom of the OSD screen.
English-43
English
Basic operation of OSD
OSD screen functions
PICTURE
„
BRIGHTNESS
RED
You can adjust the brightness.
Press the PLUS (+) button to increase the brightness. Press
the MINUS (-) button to decrease the brightness.
NOTE: You cannot adjust this item when BRIGHTNESS of
SCREEN SAVER in the CONFIGURATION1 menu is
ON.
„
YELLOW
This adjustment doesn’t work in the sRGB picture
mode.
GREEN
NOTE: This adjustment doesn’t work in the sRGB picture
mode.
„
„
BLACK LEVEL
„
„
COLOR TEMPERATURE
You can adjust the color temperature.
The image becomes reddish as the color temperature
decreases, and it becomes bluish as the color temperature
increases.
NOTE: This adjustment doesn’t work in the sRGB picture
mode.
NOISE REDUCTION
* This function doesn’t work on RGB input signals.
You can adjust the noise reduction level.
Press the PLUS (+) button to increase the value to lessen
the noise.
NOTE: This adjustment doesn’t work in the sRGB picture
mode.
COLOR
[COLOR]:
You can adjust all the colors at the same time. Press the
PLUS (+) button to deepen the colors. Press the MINUS (-)
button to lighten the colors.
[RED], [MAGENTA], [BLUE], [CYAN], [GREEN], or [YELLOW]:
You can adjust each color individually. Press the PLUS (+)
button to deepen the selected color. Press the MINUS (-)
button to lighten the selected color.
NOTE: This adjustment doesn’t work in the sRGB picture
mode.
SHARPNESS
You can adjust the brightness in the dark area of the image.
Press the PLUS (+) button to brighten dark areas in the
image. Press the MINUS (-) button to further darken the
dark area of the image.
NOTE: This adjustment doesn’t work in the sRGB picture
mode.
CYAN
Color circle
You can adjust the sharpness.
Press the PLUS (+) button to make the image look sharper.
Press the MINUS (-) button to make the image look softer.
NOTE: If you increase the sharpness setting value too
much, lines may appear double. In such a case,
decrease the sharpness setting value.
„
BLUE
CONTRAST
You can adjust the contrast.
Adjust the contrast using the PLUS (+) or MINUS (-) button to
obtain a desired result.
NOTE: Brightness changes luminance of the backlight.
Contrast changes signal levels, and therefore it is
likely to lead to whiteness.
„
MAGENTA
„
TINT
[TINT]:
You can adjust all the colors at the same time. Press the
PLUS (+) button to add a green tint. Press the MINUS (-)
button to add a purple tint.
[RED], [MAGENTA], [BLUE], [CYAN], [GREEN], or [YELLOW]:
You can adjust each color individually. Press the PLUS (+)
button to shift the selected color to the right around the
color circle. Press the MINUS (-) button to shift the selected
color to the left around the color circle.
English-44
COLOR CONTROL
The color levels of red, green, and blue are adjusted by the
color bars.
R: Red, G: Green, B: Blue
NOTE: This adjustment doesn’t work in the sRGB picture
mode.
OSD screen functions (continued)
GAMMA SELECTION
You can select the gamma mode from NATIVE, S GAMMA,
2.2, 2.4, OPTION, and PROGRAMMABLE.
PROGRAMMABLE can change the GAMMA characteristic
curve via a computer.
Contact your dealer for further details.
NOTE: GAMMA is fixed to 2.2 in the sRGB picture mode.
When PROGRAMMABLE has been selected, the
setting for color temperature is fixed at 10,000 K
(NATIVE).
„
LOCAL DIMMING
For images containing many black portions, electric power
can be saved by partly controlling the backlight.
NOTE: You might feel a sense of incongruity in movement
depending on the video. If this happens, turn the
setting to OFF.
„
PICTURE RESET
You can reset all the PICTURE settings to the factory
defaults.
English-45
English
„
OSD screen functions (continued)
SCREEN
„
„
H POSITION
You can adjust the horizontal image position.
Press the PLUS (+) button to move the image to the right.
Press the MINUS (-) button to move the image to the left.
„
V POSITION
You can adjust the vertical image position.
Press the PLUS (+) button to move the image up. Press the
MINUS (-) button to move the image down.
„
CLOCK
* For the D-SUB inputs only.
You can adjust the image size of the computer and eliminate
blurred letters.
Press the PLUS (+) button to expand the width of the image
on the screen to the right. Press the MINUS (-) button to
narrow the width of the image on the screen to the left.
„
„
„
„
V RESOLUTION
* For the D-SUB inputs only.
Use this setting when AUTO SETUP and AUTO ADJUST
cannot obtain the vertical resolution of the input signal.
Press the PLUS (+) button to increase the resolution. Press
the MINUS (-) button to decrease the resolution.
ZOOM MODE
You can select the mode to stretch the image to fit it to the
screen.
For the HDMI, DVI-D, D-SUB, and DISPLAYPORT inputs,
you can select FULL, NORMAL, CUSTOM, or REAL.
For YPbPr and VIDEO, you can select FULL, NORMAL,
DYNAMIC, CUSTOM, or REAL.
FULL:
The image is stretched to fill the screen
regardless of its aspect ratio.
NORMAL: The image is stretched vertically to the full
height of the screen while keeping the aspect
ratio.
DYNAMIC: The image is stretched to fill the screen with
different magnifications at the screen center
and the screen edges.
CUSTOM: You can stretch the image horizontally and
vertically as you desire using the CUSTOM
ZOOM setting.
REAL:
The image is displayed without being stretched
or reduced.
NOTE: The DYNAMIC mode displays images having the
16:9 aspect ratio, such as those with 1920 x 1080
resolution, in the same way as in the FULL mode.
H RESOLUTION
* For the D-SUB inputs only.
Use this setting when AUTO SETUP and AUTO ADJUST
cannot obtain the horizontal resolution of the input signal.
Press the PLUS (+) button to increase the resolution. Press
the MINUS (-) button to decrease the resolution.
CLOCK PHASE
* For the D-SUB inputs only.
You can adjust the level of the periodic variation of the
screen flicker.
CUSTOM ZOOM
CUSTOM ZOOM becomes selectable when you set ZOOM
MODE to CUSTOM.
ZOOM:
You can expand the horizontal and vertical
sizes simultaneously.
H ZOOM:
You can expand the horizontal size only.
V ZOOM:
You can expand the vertical size only.
H POSITION: Pressing the PLUS (+) button moves the
image to the right. Pressing the MINUS (-)
button moves the image to the left.
V POSITION: Pressing the PLUS (+) button moves the
image up. Pressing the MINUS (-) button
moves the image down.
„
English-46
SCREEN RESET
You can reset all the SCREEN settings to the factory
defaults.
OSD screen functions (continued)
English
AUDIO
„
BALANCE
You can adjust the balance of the right and left volumes.
Press the PLUS (+) button to decrease the left volume.
Press the MINUS (-) button to decrease the right volume.
„
TREBLE
You can adjust the high frequency sound.
Press the PLUS (+) button to increase the treble sound.
Press the MINUS (-) button to decrease the treble sound.
„
BASS
You can adjust the low frequency sound.
Press the PLUS (+) button to increase the bass sound.
Press the MINUS (-) button to decrease the bass sound.
„
AUDIO RESET
You can reset all the AUDIO settings to the factory defaults.
English-47
OSD screen functions (continued)
PIP (PICTURE IN PICTURE)
NOTE:
The PIP and POP functions don’t work in the CUSTOM and
REAL picture size modes.
Refer to “PIP, POP function” for details. (See page 56.)
„
„
PIP MODE
You can select the PIP MODE from PIP, POP, SBS ASPECT,
SBS FULL, and OFF using the PLUS (+) and MINUS (-)
buttons. See page 56.
SUB INPUT
You can select the video input for the sub screen from
HDMI, DVI-D, D-SUB, YPbPr (or VIDEO).
„
PIP RESET
You can reset all the PIP settings to the factory defaults.
PIP
POP
SBS ASPECT
SBS FULL
OFF
* SBS: SIDE BY SIDE
„
PIP SIZE
You can select the size of the sub picture displayed in the
PIP MODE.
You can move the sub picture by pressing the UP ( ),
DOWN ( ), PLUS (+), and MINUS (-) buttons.
„
PIP AUDIO
You can select the audio output in the PIP MODE.
When MAIN AUDIO is selected, audio of the main picture
is output. When PIP AUDIO is selected, audio of the sub
picture is output.
„
PIP H POSITION
You can adjust the horizontal position of the sub screen.
Press the PLUS (+) button to move the sub screen to the
right. Press the MINUS (-) button to move the sub screen to
the left.
„
PIP V POSITION
You can adjust the vertical position of the sub screen.
Press the PLUS (+) button to move the sub screen up. Press
the MINUS (-) button to move the sub screen down.
English-48
OSD screen functions (continued)
English
CONFIGURATION1
„
When you select a time period in the MOTION
setting, the monitor enlarges the image and moves it
horizontally and vertically. The portions of the image
out of the display area aren’t visible.
To make the entire image visible all the time, arrange
it to fit within 90% of the screen area at the center.
AUTO SETUP
* For the D-SUB inputs only.
The screen size, horizontal/vertical position, clock, clock
phase, and input signal level are automatically adjusted.
„
AUTO ADJUST
* For the D-SUB inputs only.
When AUTO ADJUST is ON, the horizontal position, vertical
position, and clock phase are automatically adjusted at the
time of the timing switching.
„
Motion
90%
„
LANGUAGE
SCREEN SAVER
You can set the SCREEN SAVER functions to reduce the
risk of “image persistence.”
GAMMA:
When you select ON, apply optimized gamma setting to
prevent image persistence.
COOLING FAN:
When you select ON, the cooling fan always runs.
When you select AUTO, the built-in fan automatically starts
running according to the operating temperature.
BRIGHTNESS:
When you select ON, the brightness decreases.
MOTION:
The screen slightly moves horizontally and vertically
at regular intervals to reduce the effect of the image
persistence.
NOTE: While TILING in the ADVANCED OPTION menu is
active, you cannot set MOTION to ON.
COLOR SYSTEM
* For the VIDEO inputs only.
You can select the color system depending on the video
device you use.
AUTO:
NTSC, PAL, SECAM, PAL-60 or 4.43 NTSC is
automatically selected.
NTSC:
NTSC
PAL:
PAL
SECAM:
SECAM
4.43NTSC: 4.43 NTSC
PAL-60:
PAL-60
NOTE: When you use a video device purchased from
overseas, set the COLOR SYSTEM menu.
OSD control menus are available in eight languages.
(English, German, Spanish, French, Italian, Portuguese,
Chinese, and Japanese)
„
Move
The portion (shaded part) outside the
display area isn’t displayed.
POWER SAVE
When the power saver in the OSD menu is turned ON, the
power management function works.
RGB: When the sync signal of computer input (HDMI,
DVI-D, D-SUB, or DISPLAYPORT) is terminated,
the monitor will be in the sleep mode in several
seconds.
VIDEO: When the sync signal of video input (YPbPr or
VIDEO) is terminated, the monitor will be in the
sleep mode in approximately 10 minutes.
NOTE: When an expansion module is in the option slot,
this function is invalid and the monitor doesn’t enter
the sleep mode even when you set this function to
ON. Even when you select other image source, the
monitor doesn’t enter the sleep mode.
„
Enlarged
„
SIDE BORDER COLOR
You can adjust the brightness of the area where no images
are displayed when a 4:3 image is displayed in the NORMAL
mode in the ZOOM MODE or the POP or other modes in the
PIP MODE.
„
CONFIGURATION RESET
The settings made in the CONFIGURATION1 and
CONFIGURATION2 menus are reset to the factory defaults.
However, the LANGUAGE, CONTROL TIME OUT, MONITOR
ID, SCHEDULE, and DATE AND TIME settings aren’t reset.
„
English-49
FACTORY RESET
The settings made in the PICTURE, SCREEN, AUDIO,
CONFIGURATION1, CONFIGURATION2, and ADVANCED
OPTION menus are reset to the factory defaults.
In addition, the picture mode selected by the wireless
remote control is reset to the factory default.
However, LANGUAGE, CONTROL TIME OUT, MONITOR ID,
SCHEDULE, DATE AND TIME, and DDC/CI aren’t reset.
OSD screen functions (continued)
CONFIGURATION2
„
„
SERIAL CONTROL
Select the communication interface (RS-232C, OPS (OPScompliant computer), or LAN) for the serial communication
function.
For connection of the signal cable, see page 23 to 26.
„
LAN SETTING
You can set the communication parameters for the LAN
network.
DHCP CLIENT
Select whether to use DHCP client or not.
Select OFF when not using it, and select ON when using
it.
IP ADDRESS
When DHCP CLIENT is OFF, set the IP address of the
monitor.
When DHCP CLIENT is ON, you can check the value set
by the DHCP server.
SUBNET MASK
When DHCP CLIENT is OFF, set the gateway mask. Set it
to 255.255.255.0 for normal use.
When DHCP CLIENT is ON, you can check the value set
by the DHCP server.
DEFAULT GATEWAY
When DHCP CLIENT is OFF, set the IP address of the
gateway router to externally connect the local area
including the monitor.
When DHCP CLIENT is ON, you can check the value set
by the DHCP server.
PORT
The port number (3007 and 63007) of the monitor is
displayed.
RESET
LAN settings are reset.
„
CONTROL TIME OUT
When using remote control, the timeout for transmission
intervals among codes within the control command can be
set.
10ms: Set the time out intervals to 10 milliseconds.
2s:
Set the time out intervals to 2 seconds.
30s: Set the time out intervals to 30 seconds.
„
MONITOR ID
ID numbers for wireless remote control are assigned to
LM55S1 (W) monitors that are multi-connected via RS-232C.
ID numbers 1 to 104 are selectable.
„
OSD TURN OFF
The OSD control menu will stay on as long as it is used.
The preset choices are 5 -120 seconds.
„
OSD H POSITION
You can adjust the horizontal position of the OSD menu.
„
OSD V POSITION
You can adjust the vertical position of the OSD menu.
„
OSD ROTATION
The OSD screen is rotated.
OFF
90
H MIRROR
V MIRROR
Horizontally
rotated
Vertically
rotated
180
CONTROLLER SETTING
When controlling the monitor via a network using a 2-Series
control processor made by Crestron, set the communication
parameters.
CONTROLLER IP
Set the IP address of the control processor.
PORT
Set the port number used for communication.
IP ID
Set the IP identification number.
NOTE: For the detailed setting procedures, see the
operation manual of the control processor made by
Crestron.
English-50
90 degree
rotation
180 degree
rotation
OSD screen functions (continued)
INFORMATION OSD
You can enable and disable the information OSD display.
The display time is selectable from 3 to 10 seconds.
NOTE: The information OSD display shows a message
when the input source is switched, the input signal
state is changed, or the input signal has an error.
„
OFF TIMER
You can select the OFF TIMER mode.
Select the time period to automatically turn off the power
from 1 to 24 hours.
NOTE: When OFF TIMER is enabled, the SCHEDULE
settings (see page 37) will be disabled.
„
SCHEDULE
You can program the LCD monitor operation schedules. (See
page 38.)
< HOW TO SETUP SCHEDULE >
Using the “SCHEDULE” function allows you to set up to
seven different scheduled time intervals when the LCD
Monitor will be activated.
You can select the time the monitor turns on and turns off,
the day of week the monitor is activated, and which input
source the monitor will use for each scheduled activation
period. A check mark in the box next to the number of the
schedule indicates that the selected schedule is in effect.
To select which schedule to set, use the up/down arrows to
move the number (1 to 7) of the schedule.
Use the (+) and (-) buttons to move the cursor horizontally
within the particular schedule. Use the and buttons
to increase the time and select the input port. The “SET”
button is used to make a selection.
If you create a schedule but do not want to set the power
on time, select “--” in the “ON” time slot.
If you do not want to use a power off time select “--” in the
“OFF” time slot.
If there is no input selected (“--” showing in the input spot)
the input from the previous schedule will be used.
The selection of EVERY DAY within a schedule takes priority
over other schedules that are set up to operate weekly.
When schedules are overlapping, scheduled Power ON time
has priority over scheduled Power OFF time.
If there are two schedules programmed for the same time,
then the highest numbered schedule has priority.
When OFF TIMER is enabled, the “SCHEDULE” settings are
disabled.
„
DATE AND TIME
You can adjust the current date and time for the internal
clock.
You must set this item when using SCHEDULE.
After completed the setting, be sure to press the SET
button (button 5 on page 10). When using a button of the
monitor, use the INPUT button (button 5 on page 8).
„
MONITOR INFORMATION
The model name and the serial number of your monitor are
displayed.
The MAC address of LAN is displayed.
English-51
English
„
OSD screen functions (continued)
ADVANCED OPTION
„
* For the D-SUB inputs only.
If the monitor fails to recognize the input signal resolution
correctly, you can select a proper resolution manually.
Only when a signal having a resolution close to any of the
following values from three groups, the values in the most
appropriate group are selectable.
Group 1: AUTO, 1024 x 768, 1280 x 768, 1360 x 768, 1366 x 768
Group 2: AUTO, 1400 x 1050, 1680 x 1050
Group 3: AUTO, 1600 x 1200, 1920 x 1200
„
When an expansion module is mounted, the
monitor doesn’t enter the sleep mode.
OFF
The video input isn’t selected automatically.
„
INPUT CHANGE
„
INPUT DETECT
This function detects whether the video signals are present
or not at the video inputs and automatically select them.
The priority applies when more than one signal is input at
the same time. The signal being displayed isn’t changed
even when a signal with higher priority is input.
AUTO SELECT
The target video inputs are DVI-D and D-SUB. When the
currently selected input signal is lost, this function checks
whether the signal is present at the other input. When
present, the other input is automatically selected.
If no signal is present at both inputs for five seconds, the
monitor enters the sleep mode.
When an expansion module such as the SDI BOX is in the
option slot, OPTION is targeted instead of DVI-D.
The priority of the input signal is as follows:
DVI-D > D-SUB
NOTE: You cannot select other inputs than DVI-D,
OPTION, and D-SUB.
SCAN CONVERSION
* This function doesn’t work when the D-SUB video input
is selected.
It works on interlace signals only.
You can select the IP conversion mode.
PROGRESSIVE: Interlace signals are converted into
progressive signals. Select this setting for
normal cases.
INTERLACE:
Interlace signals are displayed without
being converted. Though this setting is
suitable for motion images, still images
aren’t displayed properly.
You can select the time for input switching from QUICK and
NORMAL.
NOTE: When you select QUICK, slight noise may appear.
„
SCAN MODE
* This function doesn’t work when the D-SUB video input
is selected.
You can select the image display area.
OVERSCAN: About 95% of the input image is displayed.
UNDERSCAN: Almost 100% of the input image is
displayed.
BLACK LEVEL EXPANSION
* For the HDMI-HD, DVI-D-HD, DISPLAYPORT
(YCbCr signal), OPTION (YCbCr signal), YPbPr, and
VIDEO inputs only.
Select the level of black expansion from OFF, MIDDLE, and
HIGH.
„
The priority of the input signal is as follows:
HDMI > YPbPr
NOTE: You cannot select DVI-D, OPTION, and
DISPLAYPORT.
INPUT RESOLUTION
„
When an expansion module is mounted, the
monitor doesn’t enter the sleep mode.
VIDEO DETECT
The target video inputs are HDMI, YPbPr, and D-SUB.
When the HDMI or YPbPr input is detected, the detected
input is automatically selected.
When the video signal being displayed is lost, the D-SUB
input is automatically selected.
English-52
FILM MODE
* This function doesn’t work when the D-SUB video input
is selected.
It works on interlace signals only.
You can select the film mode function.
AUTO: Images of 24 frames per second are detected,
subjected to interpolation, and then displayed.
OFF: The input video signals are displayed without being
subjected to any processing.
NOTE: When FILM MODE is AUTO, set SCAN
CONVERSION to PROGRESSIVE. See page 52.
OSD screen functions (continued)
„
IR CONTROL
You can lock the wireless remote control.
Select from the following 4 modes using the
and
buttons and then determine the selected mode by pressing
the SET button.
NORMAL:
All the remote control operations are
enabled.
PRIMARY:
The first LM55S1 (W) monitor of those multiconnected via RS-232C is designated as
PRIMARY.
SECONDARY: LM55S1 (W) monitors other than the first
one multi-connected via RS-232C are
designated as SECONDARY.
LOCK:
All the remote control operations are
disabled.
NOTE: When you hold down the DISPLAY button on the
wireless remote control for at least 8 seconds, the
NORMAL mode is activated.
You can lock the wireless remote control
independently from the control buttons on the rear
of the monitor. See page 54.
„
„
When TILING is activated, PIP, POP, SBS, and STILL
are disabled.
TILING doesn’t work in the REAL picture size mode.
While TILING is active, you cannot set MOTION of
SCREEN SAVER in the CONFIGURATION1 menu to
ON.
HDMI SIGNAL:
Select this setting when displaying HDMI or OPTION (when
an OPS-compliant computer is mounted).
Select FULL when displaying the signal that uses all 256
levels (from level 0 to 255). This mode is used primarily
when input comes from a computer.
Select LIMITED when displaying the signal that uses 16
to 235 levels of 256 levels for each of R, G, and B. This
mode is used primarily when input comes from a video
device.
HDMI MODE:
Select this setting when displaying the HDMI signal.
Select HDMI-HD when the source device is a video
device.
Select HDMI-PC when the source device is a PC.
DVI MODE:
Select this setting when displaying the DVI-D signal.
Select DVI-PC when the source device is a PC.
Select DVI-HD when the source device is a video
device.
„
„
CLOSED CAPTION
You can select to display or hide captions.
OFF:
Captions are hidden.
CC1:
Captions are displayed in sync with the
primary audio.
CC2:
Information (related to the primary
audio) is displayed without sync.
CC3:
Captions are displayed in sync with the
secondary audio.
CC4:
Information (related to the secondary
audio) is displayed without sync.
TT1/TT2/TT3/TT4: Four types of information not related to
the displayed images are displayed. (For
example, news and weather forecast.)
NOTE: Check with each supplier of your video software and
external video devices in advance whether they are
compliant with EIA-608-A.
If their video signals are not compliant with it,
images may not be displayed correctly.
Select the number of images obtained by
horizontal division.
V MONITORS: Select the number of images obtained by
vertical division.
POSITION:
Select the area you want to enlarge.
FRAME COMP.: When displaying an image across multiple
monitors, you can select the mode to
compensate for the bezel widths for
smooth and natural display.
ENABLE:
When you select ON, the image in the
selected area is enlarged on the screen.
HEAT STATUS
The statuses of the cooling fan, brightness, and internal
temperature are displayed.
NOTE: The cooling fan starts running according to the
operating temperature or when COOLING FAN is
ON in the SCREEN SAVER menu.
When the operating temperature substantially
exceeds the operation guaranteed range, the
message “TEMPERATURE WARNING” is displayed
on the screen.
DDC/CI
Use to turn ON or OFF the DDC/CI communication function.
Select ON for normal use.
H MONITORS:
„
TERMINAL SETTING
You can select the mode to display the HDMI or DVI-D
signal according to their signal format depending on their
source device.
TILING
TILING is a function to divide or enlarge images and display
them across multiple screens. You can divide an input video
up to five pieces horizontally and vertically and display
them on a single large screen comprised of up to 25 (5 x 5)
monitors tiled together.
NOTE: A same video signal needs to be input to each
monitor. When different monitors need to be
adjusted so that their tint can be identical, it
is recommended to use a signal distributor
(commercially available).
POWER ON DELAY
You can adjust the delayed time until the power-on mode
is activated at the time of recovery from the sleep mode or
power-on.
The time is selectable from OFF and 2, 4, 6, 8, 10, 20, 30,
40, and 50 seconds.
„
English-53
ADVANCED OPTION RESET
The settings made in the ADVANCED OPTION menus are
reset to the factory defaults.
However, DDC/CI isn’t reset.
English
„
Other functions
Picture size
OSD information
HDMI, DVI-D, D-SUB, OPTION (OPS-compliant computer),
DISPLAYPORT
FULL
NORMAL
CUSTOM
REAL
OPTION (SDI), YPbPr, VIDEO
FULL
NORMAL
DYNAMIC
NORMAL
CUSTOM
REAL
NORMAL
(Squeeze signal)
NORMAL
DYNAMIC
DVI-D
1024 x 768
48kHz 60Hz
AUDIO : ANALOG
SIZE : FULL
Current selection (DVI-D)
Resolution
Horizontal/vertical frequency
Audio input mode
Picture size mode
OPTION (SDI)
OPTION : SDI (3G)
1920 x 1080
67kHz 60Hz
AUDIO : SDI
SIZE : FULL
Normal size of
each signal
NORMAL
HDMI, DVI-D, D-SUB, DISPLAYPORT
FULL
3G-SDI format is selected.
Resolution
Horizontal/vertical frequency
Audio input mode
Picture size mode
Recommend
picture size
OPTION (OPS-compliant computer)
NORMAL:
Images supplied from external devices such
as PC and DVD fit the screen, keeping their
original aspect ratio.
FULL:
Images are displayed on the entire screen.
DYNAMIC:
4:3 images are enlarged on the entire
screen with non-linearity. (Round images
may be cut when enlarged.)
CUSTOM (ZOOM): You can enlarge the displayed images
beyond the active display area. The portions
of the image out of the display area aren’t
visible.
REAL:
Images are displayed in their original sizes.
OPTION : PC
1920 x 1080
67kHz 60Hz
AUDIO : OPS DIGITAL
SIZE : FULL
Current selection
(OPTION (OPS-compliant computer))
Resolution
Horizontal/vertical frequency
Audio input mode
Picture size mode
YPbPr
YPbPr
AUDIO : ANALOG
SIZE : FULL
Current selection (YPbPr)
Audio input mode
Picture size mode
ZOOM
VIDEO
VIDEO
NTSC
AUDIO : ANALOG
SIZE : FULL
ZOOM
Current selection (VIDEO)
Color system mode
Audio input mode
Picture size mode
Picture mode
HDMI*, DVI-D, D-SUB, OPTION (OPS-compliant computer),
DISPLAYPORT
HIGHBRIGHT
STANDARD
sRGB
PIP, POP
Main : DVI-D
Sub : VIDEO
DVI-D
1024 x 768
48kHz 60Hz
AUDIO : ANALOG
VIDEO
NTSC
SIZE : FULL
HDMI*, OPTION (SDI), YPbPr, VIDEO
HIGHBRIGHT
STANDARD
CINEMA
* Automatically selected depending on the input signal.
Control Lock mode
You can lock the operation buttons so that the image
adjustments you made aren’t changed even when the buttons
are pressed.
By holding down both the and button on the monitor for
3 seconds or longer, you can lock the operation buttons.
By holding down both the and button on the monitor for
3 seconds or longer again, you can unlock the operation
buttons.
English-54
Main picture information
Audio input mode
Sub picture information
Main picture size
Other functions (continued)
You can select the audio input using the AUDIO INPUT button.
Note that the selectable audio inputs vary depending on the currently selected video signal input.
Selection of the video signal input
HDMI
DVI-D
D-SUB
PC (OPS-compliant computer)
Operation
HDMI
AUDIO IN1
AUDIO IN2
AUDIO IN1
AUDIO IN2
AUDIO IN1
AUDIO IN2
OPTION
AUDIO IN1
AUDIO IN2
SDI
AUDIO IN1
AUDIO IN2
DP
AUDIO IN1
AUDIO IN2
AUDIO IN1
AUDIO IN2
AUDIO IN1
AUDIO IN2
OPTION*
SDI (SDI BOX)
DISPLAYPORT
YPbPr
VIDEO
* OPTION can be used when an expansion module is mounted on the option slot.
English-55
English
Audio input change
Other functions (continued)
PIP, POP function
The following table shows the combinations of signal inputs with which the “PIP” and “POP” modes function. However, these modes
do not function when the screen size is “CUSTOM” or “REAL”.
Main screen
Sub screen
HDMI
DVI-D
D-SUB
OPTION*
DISPLAY
PORT
YPbPr
VIDEO
HDMI
×
×
×
×
×
×
{
DVI-D
×
×
×
×
×
×
{
D-SUB
×
×
×
×
×
×
{
OPTION*
×
×
×
×
×
×
{
DISPLAYPORT
×
×
×
×
×
×
{
YPbPr
×
×
×
×
×
×
×
VIDEO
{
{
{
{
{
×
×
× : Not supported
{ : Supported
* OPTION can be used when an expansion module is mounted on the option slot.
By pressing the PIP ON/OFF button on the wireless remote control, you can change the PIP, POP, and SBS modes in the order
shown below.
Alternatively, you can change the modes using the PIP MODE setting of PIP in the OSD main menu. See page 48.
PIP
POP
SBS ASPECT
SBS FULL
OFF
The resolutions in the PIP and SBS FULL modes are as follows:
PIP SIZE
< SMALL >
: 450 pixels X 338 pixels
< MIDDLE >
: 675 pixels X 450 pixels
< LARGE >
: 900 pixels X 675 pixels
SBS FULL
: 960 pixels X 1080 pixels
NOTE:
When the PIP or SBS FULL mode has been selected, images in the sub picture always fit the size of each mode shown above
irrespective of the aspect ratio of the input image.
English-56
Other functions (continued)
By connecting multiple LM55S1 (W) monitors using RS-232C cables, you can control any one monitor or all the monitors by one
remote controller.
NOTE:
• You cannot use the remote control numbering function if monitors are multi-connected using REMOTE IN/OUT.
1. Assign arbitrary ID number to each of multi-connected LM55S1 (W) monitors using MONITOR ID.
You can set 1 to 26 for a monitor ID of LM55S1 (W) that is intended to set as PRIMARY.
You can set 1 to 104 for a monitor ID of LM55S1 (W) that is intended to set as SECONDARY.
While you are setting a MONITOR ID, leave the remote control mode as NORMAL.
It is recommended to assign sequential ID numbers from 1 and up.
2. The remote control mode of the first LM55S1 (W) monitor is set to PRIMARY and those of the other monitors are set to
SECONDARY.
3. When you direct the remote controller at the remote control signal sensor of the PRIMARY monitor and press the DISPLAY
button on the remote controller, the ID selection OSD appears at the upper left of the screen.
ID:1
ID No. :2
ID number of the currently viewed monitor
Select the ID number of the monitor you want to control using the +/- button on the remote controller.
The ID of the monitor you want to control is displayed at the upper left of its screen.
By selecting ALL, you can control all the multi-connected monitors.
4. Direct the remote controller at the remote control signal sensor of the PRIMARY monitor.
OSD appears on the monitor having the ID number you selected.
NOTE:
When the ID selection OSD is being displayed on the PRIMARY monitor, press the DISPLAY button on the remote controller again to
cancel the ID selection OSD and then control the monitor you selected.
Do not send the control command from the computer and operate the remote control at the same time. Failure to do so may cause
improper operation of the LCD monitor.
If you set the remote control mode wrongly and remote control operation becomes unavailable, press any button on the control
panel of the monitor to display the OSD screen and change the remote control mode using ADVANCED OPTION. By pressing and
holding down the DISPLAY button on the remote control for 8 seconds or longer, the remote control mode is initialized to NORMAL.
English-57
English
Remote control numbering function
Troubleshooting
No picture
• The signal cable should be securely connected to the display card/computer.
• The display card should be securely seated in its slot.
• The Main Power Switch and the computer power switch should be in the ON position.
• Make sure that the correct mode has been selected on the display card or system being used.
(Please consult the display card or system manual to change the graphics mode.)
• Check the monitor and your display card with respect to the compatibility and recommended settings.
• Check the signal cable connectors for bent or pushed-in pins.
Power button does not respond
• Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.
Image persistence
• Please be aware that LCD Technology may experience a phenomenon known as “image persistence.” Image persistence occurs
when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image
persistence is not permanent, but constant images being displayed for a long period of time should be avoided. To alleviate
image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the
monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.
NOTE:
As with all display devices, MITSUBISHI ELECTRIC recommends displaying moving images and using a moving screen saver at
regular intervals whenever the screen is idle or turning off the monitor when not in use.
Image is unstable, unfocused or swimming is apparent
• Signal cable should be securely attached to the computer.
• Use the OSD Image Adjust controls to focus and adjust the display by increasing or decreasing the fine adjustment.
When the display mode is changed, the OSD Image Adjust settings may need to be re-adjusted.
• Check the monitor and your display card with respect to the compatibility and recommended signal timings.
• If the displayed text is garbled, change the video mode to the non-interlace mode and use 60 Hz refresh rate.
Image of component signal is greenish
• Check to see if the YPbPr input connector is selected.
LED on the monitor is not lit (No green or red color can be seen)
• Power Switch should be in the ON position and power cord should be connected.
• Make certain the computer is not in the power-saving mode (touch the keyboard or mouse).
RED LED on the monitor is blinking
• A certain failure may have occurred. Please contact your nearest authorized MITSUBISHI ELECTRIC service facility.
Displayed image is not sized properly
• Use the OSD Image Adjust controls to increase or decrease the coarse adjustment.
• Make sure that the correct mode has been selected on the display card or system being used.
(Please consult the display card or system manual to change the graphics mode.)
Selected resolution is not displayed properly
• Use OSD Display Mode to enter Information menu and check that the appropriate resolution has been selected. If not, select
corresponding option.
No sound
• Check to see if the speaker cable is properly connected.
• Check to see if the mute is activated.
• Check to see if the volume is set to the minimum level.
Wireless remote control is not available
• Check the wireless remote control’s batteries status.
• Check if the batteries are inserted correctly.
• Check if the wireless remote control is pointing at the monitor’s remote sensor.
• If the wireless remote control is not working properly, connect the IR sensor supplied with the remote control kit (option).
“SCHEDULE”/“OFF TIMER” function is not working properly
• The “SCHEDULE” function will be disabled when the “OFF TIMER” is set.
• If the “OFF TIMER” function is enabled and the power to the LCD monitor is turned off if the power supply is interrupted
unexpectedly, then the “OFF TIMER” will be reset.
Either light vertical or horizontal stripes may appear, depending on the specific display pattern. This is no product fault or
degradation.
English-58
Model
LM55S1 (W)
Orientation
Landscape/Portrait
121.2
Dimension (Unit: mm)
1.9
686.3
681
3.4
3.4
1215.5
1.9
1210.2
LCD Module
Screen size (diagonal)
54.6” (1388 mm)
Panel Type
IPS
Pixel Pitch
0.630 mm
Resolution
1920 x 1080 pixels
Color
Approximately 1.06 billion colors
Brightness (typ.)
500 cd/m2
Contrast ratio
1300 : 1
Viewing Angle (CR>
=10)
Up/Down 178°, Left/Right 178°
Response time
10 ms (Gray to Gray)
Viewable Size (H x V)
1209.6 mm x 680.4 mm / 47.6” x 26.8”
Power Management
VESA DPM
Plug and Play
VESA DDC2B, DDC/CI
Auto Adjustment
Yes (Contrast / Position / Phase / Clock)
OSD user functions
Brightness, Contrast, Black level, Zoom, PIP, Screen saver, Side border color, Gamma
selection, Heat status, Power on delay, Schedule, Tiling, LAN control, Closed caption, etc.
Input Connector
Output Connector
(Analog)
MINI D-SUB 15-pin
(Digital)
HDMI (PC/AV Common), DVI-D (HDCP supported, PC/AV Common), DISPLAYPORT
(Digital)
DVI-D (HDCP supported except for Macintosh, PC/AV Common)
Horizontal Frequency
Analog: 15.625/15.734, 31.5 kHz - 91.1 kHz, Digital: 31.5 kHz - 91.1 kHz
Vertical Frequency
50/58 Hz - 85 Hz
PC Input / Output
Pixel Clock
(Analog)
13.5 - 165.0 MHz
(Digital)
25.0 - 165.0 MHz
Video Signal
Analog: Analog RGB, Digital: TMDS (with HDCP)
Sync Signal
Analog: Separate (TTL), Composite (TTL), Sync on Green, Digital: TMDS
Supported Resolution
Input Connector
(Digital)
Input / Output Signal
AV Input / Output
Audio Input / Output
Digital: DVI-D (HDCP supported, PC/AV Common), SDI (option)
Supported Resolution
Composite: NTSC, PAL, SECAM, 4.43 NTSC, PAL-60
Component: 480i, 480p, 576i, 576p, 1080i, 720p, 1080p
SDI: 480i/576i (SD-SDI), 720p/1080i (HD-SDI), 1080p (3G-SDI)
Output Connector
External speaker output
Option slot
Slot interface
Built-in Speaker Output
Control Input / Output
HDMI (digital audio), DISPLAYPORT, SDI (option)
(Analog)
RCA pin jack L/R
(Digital)
SDI (option)
Speaker connector L/R (impedance 8 Ω)
Digital (OPS) slot (16 V / 2.3 A)
RS-232C <D-SUB 9-pin>, LAN <Modular 8-pin>
Output Connector
RS-232C <D-SUB 9-pin>
Power Supply
Power Consumption at Power Saving
Weight
RCA pin jack L/R, ø3.5-mm stereo mini jack
(Digital)
Input Connector
Power Consumption
Dimension
(W x H x D)
(Analog)
Audio output 10 W + 10 W (stereo)
Input Voltage / Current
Storage Environment
HDMI (PC/AV Common), DVI-D (HDCP supported, PC/AV Common), SDI (option)
Output Connector
Input Connector
Operation Environment
(Analog)
640 x 480, 800 x 600, 1024 x 768, 1280 x 768, 1360 x 768, 1280 x 1024,
1600 x 1200 (Compressed/Simplified), 1920 x 1080, 1920 x 1200 (Compressed/Simplified)
Composite video <BNC (Y: shared with component video)>,
Component (Y/Pb/Pr) <BNC>
2.6 A - 1.1 A @AC100 - 240 V, 50/60 Hz
253 W (with ARK-DS262GQ-U5A1E of Advantech Co., Ltd.)
(195 W without speaker, option slot)
Sleep mode: Less than 4.0 W (with ARK-DS262GQ-U5A1E of Advantech Co., Ltd.)
Power switch off: Less than 0.5 W
Main power switch off: 0 W
Temperature
0 - 40°C / 32 - 104°F (Landscape position), 0 - 35°C / 32 - 95°F (Portrait position)
Humidity
20 - 80% (without condensation)
Temperature
-20 - 60°C / -4 - 140°F
Humidity
10 - 90% (Without condensation) / 90% - 3.5% x (Temp-40°C) regarding over 40°C
Net (without stand)
1215.5 mm (W) x 686.3 mm (H) x 121.2 mm (D) / 47.9” (W) x 27.0” (H) x 4.8” (D)
Gross
1556 mm (W) x 979 mm (H) x 455 mm (D) / 61.3” (W) x 38.5” (H) x 17.9” (D)
Net (without stand)
Approximately 37.0 kg / 81.6 lbs
Gross
Approximately 55.0 kg / 121.3 lbs
Wall mounting interface
4-M6 Screws holes (400 mm / 15.7” pitches) for Monitor mount
Complied regulatory and guidelines
UL60950-1 / C-UL / EN60950-1 / CE / BSMI / CU / FCC-A / DOC-A / EN55022-A / EN55024 /
EN61000-3-2 / EN61000-3-3 / C-Tick / RoHS / US Mercury
NOTE: Technical specifications are subject to change without notice.
English-59
English
Specifications
Pin Assignment
1) Analog RGB input: D-SUB
Pin No
Name
Pin No
Name
1
Video Signal Red
9
+5V (DDC)
2
Video Signal Green
10
SYNC-GND
3
Video Signal Blue
11
GND
4
GND
12
DDC-SDA
5
DDC-GND
13
H-SYNC
6
Red-GND
14
V-SYNC
7
Green-GND
15
DDC-SCL
8
Blue-GND
Mini D-SUB 15-pin
1
5
6
10
11
15
2) Digital RGB input: HDMI
Pin - Assignment of HDMI connector:
1
TMDS Data2+
8
TMDS Data0 Shield
HDMI
15 SCL
2
TMDS Data2 Shield
9
TMDS Data0-
16 SDA
3
TMDS Data2-
10 TMDS Clock+
17 DDC/CEC Ground
4
TMDS Data1+
11 TMDS Clock Shield
18 +5V Power
5
TMDS Data1 Shield
12 TMDS Clock-
19 Hot Plug Detect
6
TMDS Data1-
13 CEC
7
TMDS Data0+
14
Reserved (N.C. on
device)
19
1
2
18
3) Digital RGB input: DVI-D
Pin - Assignment of DVI-D connector:
1
TMDS Data2-
9
TMDS Data1-
17 TMDS Data0-
2
TMDS Data2+
10 TMDS Data1+
18 TMDS Data0+
3
TMDS Data2 Shield
11 TMDS Data1 Shield
19 TMDS Data0 Shield
4
NC
12 NC
20 NC
5
NC
13 NC
21 NC
6
DDC Clock
14 +5V Power
22 TMDS Clock Shield
7
DDC Data
15
8
Analog Vertical Sync
16 Hot Plug Detect
Ground (return for +5V,
23 TMDS Clock+
H-SYNC and V-SYNC)
DVI-D
8
1
9
16
24
17
24 TMDS Clock-
4) Digital RGB input: DISPLAYPORT
Pin No
Name
Pin No
Name
1
ML_Lane 3 (n)
11
GND Top
2
GND
12
ML_Lane 0 (p)
3
ML_Lane 3 (p)
13
CONFIG1
4
ML_Lane 2 (n)
14
CONFIG2
5
GND
15
AUX CH (p)
6
ML_Lane 2 (p)
16
GND
7
ML_Lane 1 (n)
17
AUX CH (n)
8
GND
18
Hot Plug Detect
9
ML_Lane 1 (p)
19
Return
10
ML_Lane 0 (n)
20
DP_PWR
English-60
DISPLAYPORT
19
20
1
2
Pin Assignment (continued)
5) RS-232C input/output
Name
1
NC
2
RXD
3
TXD
4
NC
5
GND
6
NC
7
NC
8
NC
9
NC
D-SUB 9-pin
1
5
6
9
6) LAN (Modular 8-pin)
Pin# at RJ45
Signal
#1
Orange/White stripe
#2
Orange
#3
Green/White stripe
#4
Blue
#5
Blue/White stripe
#6
Green
#7
Brown/White stripe
#8
Brown
Pair
Modular 8-pin
1234 5678
English-61
English
Pin No