Zanussi ZKG7145 washer dryer User manual

Add to my manuals
32 Pages

advertisement

Zanussi ZKG7145 washer dryer User manual | Manualzz
EN
User manual
Washer Dryer
ZKG 7125
ZKG 7145
ZKG 7165
Contents
Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2
Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3
Product description _ _ _ _ _ _ _ _ _ _ _ _ _ 5
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6
Washing Programmes _ _ _ _ _ _ _ _ _ _ _ _ 9
Automatic Drying programmes _ _ _ _ _ _ _ 11
Drying Programmes _ _ _ _ _ _ _ _ _ _ _ _ _ 12
Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ 12
Drying Hints _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 14
First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 14
Personalisation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Daily Use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Use - Drying _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _
What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Consumption values _ _ _ _ _ _ _ _ _ _ _ _
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Environment concerns _ _ _ _ _ _ _ _ _ _ _
15
15
17
19
22
25
26
26
29
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always
keep the instructions with the appliance for future reference.
Children and vulnerable people safety
Warning! Risk of suffocation, injury or permanent disability.
• Do not let persons, children included, with reduced physical sensory, reduced mental functions or lack of experience and knowledge use the appliance. They must have supervision or instruction
for the operation of the appliance by a person who is responsible
for their safety.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep all detergents away from children.
• Keep children and pets away from the appliance door when it is
open.
• If the appliance has a child safety device, we recommend you activate it.
General Safety
• Before maintenance, deactivate the appliance and disconnect the
mains plug from the mains socket.
2
www.zanussi.com
• Do not change the specification of this appliance.
• Obey the maximum load volume of 8 kg (refer to the “Programme
chart” chapter).
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to
avoid a hazard.
• The operating water pressure (minimum and maximum) must be
between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa)
• The ventilation openings in the base (if applicable) must not be
obstructed by a carpet.
• The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.
Safety instructions
Installation
• Remove all the packaging and the transit
bolts.
• Keep the transit bolts. When you move the
appliance again you must block the drum.
• Do not install or use a damaged appliance.
• Do not install or use the appliance where the
temperature is less than 0 °C or where it is
exposed to the weather.
• Obey the installation instruction supplied
with the appliance.
• Make sure that the floor where you install the
appliance is flat, stable, heat resistant and
clean.
• Do not install the appliance where the appliance door can not be fully opened.
• Always be careful when you move the appliance because it is heavy. Always wear safety
gloves.
• Make sure that there is air circulation between the appliance and the floor.
• Adjust the feet to have the necessary space
between the appliance and the carpet.
Electrical connection
www.zanussi.com
Warning! Risk of fire and electrical shock.
• The appliance must be earthed.
• Make sure that the electrical information on
the rating plate agrees with the power supply. If not, contact an electrician.
• Always use a correctly installed shockproof
socket.
• Do not use multi-plug adapters and extension cables.
• Make sure not to cause damage to the mains
plug and to the mains cable. Should the appliance power supply cable need to be replaced, this must be carried out by our Service Centre.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after
the installation.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
• Do not touch the mains cable or the mains
plug with wet hands.
• Only for UK and Ireland. The appliance has a
13 amp mains plug. If it is necessary to
3
change the fuse in the mains plug, use a 13
amp ASTA (BS 1362) fuse.
•
This appliance complies with the E.E.C. Directives.
Water connection
• Make sure not to cause damage to the water
hoses.
• The appliance is to be connected to the water mains using the new supplied hose-sets.
Old hose sets must not be reused.
• Before you connect the appliance to new
pipes or pipes not used for a long time, let
the water flow until it is clean.
• The first time you use the appliance, make
sure that there is no leakage.
Use
Warning! Risk of injury, electrical shock,
fire, burns or damage to the appliance.
• Use this appliance in a household only.
• Do not change the specification of this appliance.
• Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
• Do not touch the glass of the door while a
programme operates. The glass can be hot.
• Make sure that you remove all metal objects
from the laundry.
• The final part of the drying cycle occurs without heat (cool down cycle) to ensure that the
items will not be damaged.
If you stop the appliance before the end of
the drying cycle, immediately remove and
spread out all items, so that the heat can dissipate.
• If you use detergent, fabric softener or similar
products, obey the instructions on the packaging.
• Wipe away lint that has accumulated around
the appliance.
• Do not dry the damaged items which contain
padding or fillings .
4
• Do not dry items such as foam rubber (latex
foam), shower caps, waterproof textiles and
rubber backed articles.
• Before drying items that have been in contact with substances such as cooking oil,
acetone, alcohol , petrol, kerosene, spot removers, turpentine, waxes and wax removers,
wash them in hot water with an extra amount
of detergent.
• Do not dry items if industrial chemicals have
been used for cleaning.
• Make sure that no gas lighters or matches
have been left in the pockets of the clothing.
• Only dry fabrics which are applicable to dry
in the tumble dryer. Follow the instructions
on the fabric label.
• Do not dry not washed items in the appliance.
• If you have washed your laundry with a stain
remover start an extra rinse cycle before you
start the appliance.
• Plastic items are not heat resistant.
– If you use a detergent ball, remove it before you set the drying programme.
– Do not use a detergent ball when you set
a non-stop programme.
Warning! Risk of injury or damage to the
appliance.
• Do not sit or stand on the open door.
• Obey the maximum load volume.
• Do not dry dripping wet clothes in the appliance.
Care and Cleaning
Warning! Risk of injury or damage to the
appliance.
• Do not use water spray and steam to clean
the appliance.
• Clean the appliance with a moist soft cloth.
Only use neutral detergents. Do not use
abrasive products, abrasive cleaning pads,
solvents or metal objects.
Disposal
www.zanussi.com
Warning! Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children
and pets to get closed in the appliance.
Service
• Contact the Service to repair the appliance.
We recommend only the use of original
spare parts.
Product description
1 Detergent dispenser drawer
2 Control panel
1
2
3 Door opening handle
4 Rating plate
5 Drain pump
6 Adjustable feet
3
4
5
6
Detergent dispenser drawer
Compartment for detergent used for prewash and soak phase or for stain remover used
during the stain action phase (if available). The
prewash and soak detergent is added at the beginning of the wash programme. The stain remover is added during the stain action phase.
Compartment for powder or liquid detergent
used for main wash. If using liquid detergent
pour it just before starting the programme.
www.zanussi.com
5
Compartment for liquid additives (fabric softener, starch).
Follow the product manufacturer’s recommendations on quantities to use and do not exceed the
«MAX» mark in the detergent dispenser drawer. Any fabric softener or starching additives must
be poured into the compartment before starting the wash programme.
Child Safety device
Make sure that children or pets do not climb into the drum. To prevent children and pets becoming trapped inside the drum this machine
incorporates a special feature.
To activate this device, rotate the button
(without pressing it)
inside the door clockwise until the groove
is horizontal. If necessary use a coin.
To disable this device and restore the
possibility of closing
the door, rotate the
button anti-clockwise
until the groove is
vertical.
Control panel
On the following page there is a picture of the control panel. It shows the programme selector
dial as well as the buttons, pilot lights and the display. These are presented by relevant numbers on the following pages.
10
9
1
2
3
4
5
6
7
1 Programme selector dial
2 Spin button
4 Drying time button
5 Super quick button
3 Automatic drying button
6 Extra rinse button
6
8
www.zanussi.com
7 Start/Pause button
8 Delay start button
9 Door pilot light
10 Display
Table of symbols
= Rinse hold
1-8 Programme selector dial, spin speed
button, drying level and time, and
available options
Programme Selector Dial
It allows you to switch the appliance on/off and/
or to select a programme.
Spin
By pressing this button you can change the
spin speed of the selected programme or to select Rinse Hold option.
Rinse hold
By selecting this function the water of the last
rinse is not emptied out to prevent the fabrics
from creasing. Before opening the door it will
be necessary to empty out the water. To empty
out the water, please read the paragraph «At
the end of the programme».
Automatic Dry
By pressing this button you can choose the required degree of drying for cottons and synthetics:
• Cupboard dry (Cottons and Synthetics)
• Iron dry (Cottons)
The pilot light corresponding to the selected
dryness degree will illuminate.
Drying Time
If you wish to carry out a timed drying programme, press this button until the drying time
you want appears on the display according to
the fabrics (cottons or synthetics) you have to
dry. For Cottons you can select a drying time
from 10 minutes to 250 minutes (4.10). For
Synthetics you can select a drying time from 10
minutes to 130 minutes (2.10). Every time you
press this button the drying time increases by 5
mins.
www.zanussi.com
= Child Safety Lock
Available options:
Super Quick
Short cycle for lightly soiled items or for laundry
which needs only freshening up. We recommend you to reduce the fabrics loading.
Extra Rinse
This appliance is designed to save energy. If it
necessary to rinse the laundry using an extra
quantity of water (extra rinse), select this option.
Some additional rinses will be performed. This
option is recommended for people who are allergic to detergents, and in areas where the
water is very soft.
Start Pause
This button allows you to start or to interrupt
the selected programme.
Delay Start
The programme can be delayed from 30 min 60 min - 90 min, 2 hours and then by 1 hour up
to a maximum of 20 hours by means of this button.
Door light
The pilot light 9 illuminates when the programme starts and indicates if the door can be
opened:
• light on: the door cannot be opened. The
machine is working or has stopped with water left in the tub.
• light off: the door can be opened. The programme is finished or the water has been
emptied out.
• light blinking: the door is opening in a few
minutes.
7
10 Display
10.1
10.2
The display shows the following information:
10.1
Child safety lock
This device permits you to leave the appliance unattended during it's functioning.
10.2
• Duration of the selected programme
After selecting a programme, the duration is displayed in hours and minutes (for example
). The duration is calculated automatically on the basis of the maximum recommended
load for each type of fabric. After the programme has started, the time remaining is updated
every minute.
• Selected drying time
After selecting a drying programme the drying time is shown in minutes or hours and minutes.
After the programme has started, the time remaining is updated every minute.
• Delayed start
The Selected delay set by pressing the relevant button appears on the display for a few seconds, then the duration of the selected programme is displayed again. The delay time value
decreases by one unit every hour and then, when 1 hour remains, every minute.
• Alarm codes
In the event of operating problems, some alarm codes can be displayed, for example
(see paragraph «What to do if...»).
• Incorrect option selection
If an option which is not compatible with the set wash programme is selected, the message
Err is displayed at the bottom of the display for a few seconds and the integrated red light of
button 7 start flashing.
• End of programme
When the programme has finished the flashing zero ( ) is displayed, the pilot light 9 and the
pilot light of button 7 go out and the door can be opened.
8
www.zanussi.com
Washing Programmes
Programme - Maximum and Minimum Temperature
- Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry
Options
Cottons
90° - 60°
Main wash - Rinses
Maximum spin speed at 1200 rpm (ZKG 7125), 1400 rpm
(ZKG 7145), 1600 rpm (ZKG 7165)
Max. load 6 kg - Reduced load 3 kg1)
White cotton(heavily and normally soiled items).
SPIN
RINSE HOLD
SUPER QUICK
EXTRA RINSE
Cottons Eco
60° - 40°
Main wash - Rinses
Maximum spin speed at 1200 rpm (ZKG 7125), 1400 rpm
(ZKG 7145), 1600 rpm (ZKG 7165)
Max. load 6 kg
White or fast colour cotton (normally soiled items).
This programme can be selected for normally soiled cotton
items. The temperature will decrease and the washing time
will be extended. This allows to obtain a good washing efficiency by saving energy.
SPIN
RINSE HOLD
EXTRA RINSE
Cottons
60° - 30°
Main wash - Rinses
Maximum spin speed at 1200 rpm (ZKG 7125), 1400 rpm
(ZKG 7145), 1600 rpm (ZKG 7165)
Max. load 6 kg - Reduced load 3 kg1)
White or colour cotton (normally or slightly soiled
items) .
SPIN
RINSE HOLD
SUPER QUICK
EXTRA RINSE
Cottons + Prewash
60° - 40°
Prewash - Main wash - Rinses
Maximum spin speed at 1200 rpm (ZKG 7125), 1400 rpm
(ZKG 7145), 1600 rpm (ZKG 7165)
Max. load 6 kg - Reduced load 3 kg1)
White or colour cotton (heavily or normally soiled items)
SPIN
RINSE HOLD
SUPER QUICK
EXTRA RINSE
Synthetics
60° - 30°
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 3 kg - Reduced load 2 kg1)
Synthetic or mixed fabrics: underwear, coloured garments, non-shrink shirts, blouses.
SPIN
RINSE HOLD
SUPER QUICK
EXTRA RINSE
www.zanussi.com
Detergent Compartment
2)
9
Programme - Maximum and Minimum Temperature
- Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry
Options
Easy iron
40°
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 1 kg
Synthetic or mixed fabrics: selecting this programme
the laundry is gently washed and spun to avoid any creasing. In this way ironing is easier. Furthermore the machine
will perform additional rinses.
SPIN
RINSE HOLD
EXTRA RINSE
Delicates
40° - 30°
Main wash - Rinses
Maximum spin speed at 700 rpm
Max. load kg 3 - Reduced load kg 1,51)
Delicate fabrics: acrylics, viscose, polyester.
SPIN3)
RINSE HOLD
SUPER QUICK
EXTRA RINSE
Wool / Handwash
40° - Cold
Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 2 kg
Washing programme for machine washable wool as well
as for hand washable woollens and delicate fabrics. Note!
A single or bulky item may cause imbalance. If the appliance doesn’t perform the final spin phase, add more items,
redistribute the load manually and then select the spinning
programme.
SPIN
RINSE HOLD
Jeans
40°
Main wash - Rinses
Maximum spin speed at 1200 rpm
Max. load 3 kg
With this programme it is possible to wash items like
pants, shirts or jackets in denim tissue and also jersey realized with hi-tech materials. Note! The Extra Rinse option
will be activated automatically.
SPIN
RINSE HOLD
Sport Intensive
40°
Prewash - Main wash - Rinses
Maximum spin speed at 900 rpm
Max. load 2,5 kg
This programme is suitable for washing heavily soiled sport
items. The appliance will add automatically a prewash
phase before the main wash to eliminate mud stains.
SPIN
RINSE HOLD
10
Detergent Compartment
www.zanussi.com
Programme - Maximum and Minimum Temperature
- Cycle Description - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry
Rinses
Maximum spin speed at 1200 rpm (ZKG 7125), 1400 rpm
(ZKG 7145), 1600 rpm (ZKG 7165)
Max. load 6 kg
With this programme it is possible to rinse and spin cotton
garments which have been washed by hand. The machine
performs 3 rinses, followed by a final long spin.
Options
Detergent Compartment
SPIN
RINSE HOLD
EXTRA RINSE
Important!
The spin speed will automatically assume the setting for
cotton items. if required, reduce the speed to the desired
level by pressing the button 2.
Drain
Draining of water
Max. load 6 kg
For emptying out the water of the last rinse in programmes
which stop with water in the tub.
Spin
Drain and long spin
Maximum spin speed at 1200 rpm (ZKG 7125), 1400 rpm
(ZKG 7145), 1600 rpm (ZKG 7165)
Max. load 6 kg
Separate spin for hand washed garments and after programmes which stop with water in the tub. You can reduce
the spin speed to the required level by pressing the relevant button to adapt it to the fabrics to be spun.
SPIN
O/Off
For cancelling the programme which is running or to switch
the machine off .
1) If you select the Super Quick option by pressing button 5, we recommend that you reduce the maximum
load as indicated. Full loading is possible however with somewhat reduced cleaning results.
2) If using liquid detergents, a programme without PREWASH must be selected.
3) Available only with model ZKG 7125.
Automatic Drying programmes
Type of Fabric
Max Load
Cupboard dry
Suitable for items to put away without ironing
Degree of Drying
Cotton and linen (bathrobes,
bath towels, etc)
3 kg
Cupboard dry
Suitable for items to put away without ironing
Synthetics and mixed fabrics (jumpers, blouses, underwear, household linen)
2 kg
Iron dry
Suitable for ironing
Cotton and linen (sheets, tablecloths, shirts, etc.)
3 kg
www.zanussi.com
11
Drying Programmes
Degree of Drying
Suitable for items to put away
without ironing
Suitable for items to put away
without ironing
Suitable for ironing
Type of Fabric
Max Load
Cotton and linen
(bathrobes, bath towels, etc)
Synthetics and
mixed fabrics
4 kg
3 kg
1,5 kg
2 kg
1 kg
Cotton and linen
(sheets, tablecloths,
shirts, etc.)
4 kg
3 kg
1,5 kg
Spin Speed
Suggested
drying time
in Mins
1600
130-150
75-85
35-45
1400
140-160
80-90
40-50
1200
150-170
85-95
45-65
900
70-80
35-45
1600
100-120
65-75
30-40
1400
110-130
65-75
35-45
1200
120-140
70-80
40-50
In compliance with EC directive EN 50229 the cotton reference programme for the data
entered in the Energy Label must be tested dividing the maximum washing load by two equal
parts and drying with DRYING TIME each of them.
Helpful hints and tips
Sorting out the laundry
Follow the wash code symbols on each garment label and the manufacturer’s washing instructions. Sort the laundry as follows: whites,
coloureds, synthetics, delicates, woollens.
Before loading the laundry
Never wash whites and coloureds together.
Whites may lose their «whiteness» in the wash.
New coloured items may run in the first wash;
they should therefore be washed separately the
first time.
Button up pillowcases, close zip fasteners,
hooks and poppers. Tie any belts or long tapes.
Remove persistent stains before washing.
12
Rub particularly soiled areas with a special detergent or detergent paste.
Treat curtains with special care. Remove hooks
or tie them up in a bag or net.
Removing stains
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable to
treat them prior to washing.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a special detergent then rub in the soap and water.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and
dab the stain; treat several times.
www.zanussi.com
Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the
stain with the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since the
cellulose structure will already have been damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with acetone1), lay the garment on a soft cloth and dab
the stain.
Lipstick: moisten with acetone as above, then
treat stains with methylated spirits. Treat any residual marks with bleach.
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten the
fabric first with acetone1), then with acetic acid;
treat any residual marks on white fabrics with
bleach and then rinse thoroughly.
Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with detergent paste.
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the environment.
Although biodegradable, detergents contain
substances which, in large quantities, can upset the delicate balance of nature.
The choice of detergent will depend on the
type of fabric (delicates, woollens, cottons,
etc.), the colour, washing temperature and degree of soiling.
All commonly available washing machine detergents may be used in this appliance:
• powder detergents for all types of fabric
• powder detergents for delicate fabrics (60°C
max) and woollens
• liquid detergents, preferably for low temperature wash programmes (60°C max) for all
types of fabric, or special for woollens only.
The detergent and any additives must be
placed in the appropriate compartments of the
dispenser drawer before starting the wash programme.
If using liquid detergents, a programme without prewash must be selected.
Your appliance incorporates a recirculation system which allows an optimal use of the concentrated detergent.
Follow the product manufacturer’s recommendations on quantities to use and do not exceed the «MAX» mark in the detergent
dispenser drawer.
Quantity of detergent to be used
The type and quantity of detergent will depend
on the type of fabric, load size, degree of soiling
and hardness of the water used.
Follow the product manufacturers’ instructions
on quantities to use.
Use less detergent if:
• you are washing a small load
• the laundry is lightly soiled
• large amounts of foam form during washing.
Degrees of water hardness
Water hardness is classified in so-called “degrees” of hardness. Information on hardness of
the water in your area can be obtained from the
relevant water supply company, or from your local authority. If the water hardness degree is
medium or high we suggest you to add a water
softener following always the manufacturer’s instructions. When the degree of hardness is
soft, readjust the quantity of the detergent.
1) do not use acetone on artificial silk
www.zanussi.com
13
Drying Hints
Preparing the drying cycle
As a dryer, the appliance works on the condensation principle.
Therefore, the water tap must be open
and the drain hose must drain water into
a sink or into the drain pipe, even during
the drying cycle.
Attention!
Before starting the drying programme, reduce
the loads of washed laundry, in order to obtain
good performances.
Laundry not suitable for drying
• Particularly delicate items such as synthetic
curtains, woollen and silk, garments with
metal inserts, nylon stockings, bulky garments such as anoraks, bed covers, quilts,
sleeping bags and duvets must not be machine dried.
• Avoid drying dark clothes with light coloured
fluffy items such as towels as these can attract the fluff.
• Remove the laundry when the appliance has
finished drying.
• To avoid a static charge when drying is completed, use either a fabric softener when you
are washing the laundry or a fabric conditioner specifically for tumble dryers.
• Garments padded with foam-rubber or materials similar to foam-rubber must not be machine dried; they represent a fire hazard.
• Also, fabrics containing residue of setting lotions or hair sprays, nail solvents or similar
solutions must not be machine dried in order
to avoid the formation of harmful vapours.
The detergent and any additives must be
placed in the appropriate compartments of the
dispenser drawer before starting the wash programme.
If using liquid detergents, a programme without prewash must be selected.
Your appliance incorporates a re-circulation
system which allows an optimal use of the concentrated detergent.
Follow the product manufacturer’s recommendations on quantities to use and do not exceed the «MAX» mark in the detergent
dispenser drawer.
Garment labels
For drying, follow the indications given on the
manufacturer’s labels:
•
= May be tumble dried
•
= Drying at high temperature
•
= Drying at reduced temperature
•
= Do not tumble dry.
Drying cycle duration
The drying time may vary depending on:
• speed of the final spin
• dryness degree required (iron dry, store dry)
• type of laundry
• weight of the load size .
The average drying time for a timed drying are
indicated in the «Drying programmes» chapter.
The experience will help you to dry your laundry
in a more suitable way, according to the different fabrics. Take note of the duration drying
time of the already performed cycles.
Additional drying
If the laundry is still damp at the end of the drying programme, select a short drying cycle
again.
Warning! Do not over dry the laundry
in order to avoid creasing of fabrics
or garment’s shrinking.
First use
• Ensure that the electrical and water
connections comply with the installation
instructions.
14
• Remove the polystyrene block and any
material from the drum.
• Before the first wash, run a cotton cycle
at the highest temperature without any
www.zanussi.com
laundry in the machine, to remove any
manufacturing residue from the drum
and tub. Pour 1/2 a measure of deter-
gent into the main wash compartment
and start the machine.
Personalisation
Acoustic signals
The machine is provided with an acoustic device, which sounds in the following cases:
• at the end of the cycle
• if there is a fault.
By pressing the 3 and 4 buttons simultaneously
for about 6 seconds, the acoustic signal is deactivated (except if there is a fault). By pressing
these 2 buttons again, the acoustic signal is reactivated.
Child safety lock
This device permits you to leave the appliance
unattended so you do not need to worry that
children might be injured by or cause damage
to the appliance. This function remains enabled
also when the washing machine is not working.
There are two different ways to set this option:
1. Before pressing button 7: it will be impossible to start the machine.
2. After pressing button 7: it will be impossible to change any other programme or option.
To enable or disable this option press simultaneously for about 6 seconds buttons 2 and 3
appears or disuntil on the display, the icon
appears.
Daily Use
Load the laundry
Measure out the detergent and the fabric
softener
Open the door by
carefully pulling the
door handle outwards. Place the
laundry in the drum,
one item at a time,
shaking them out as
much as possible.
Close the door.
Make sure that no
laundry stays between the seal and
the door. There is a
risk of water leakage
or damage to the
laundry.
www.zanussi.com
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required, pour it into the main wash compartor in the appropriate compartment if
ment
the selected programme/option it requires
(see more details in "Detergent dispenser
drawer").
If required, pour fabric softener into the com(the amount used must
partment marked
not exceed the «MAX» mark in the drawer).
Close the drawer gently.
15
Select the required programme by means
of the programme selector dial (1)
Turn the programme selector dial to the required programme.
The green pilot light of button 7 starts to flash.
The selector dial can be turned either clockwise
or anticlockwise.
to reset the
Turn the selector dial to position
programme/to switch the machine OFF.
At the end of the programme the selector
, to
dial must be turned to position
switch the machine off.
Important! If you turn the programme selector
dial to another programme when the machine is
working, the red pilot light of button 7 will blink
3 times and the messageErr is displayed to
indicate a wrong selection. The machine will
not perform the new selected programme.
Select the spin speed by pressing button
2
When selecting a programme, the appliance
proposes automatically the maximum spin
speed provided for that programme. (See
"Washing programmes" for the maximum allowed spin speed).
Press this button repeatedly to change the spin
speed, if you want your laundry to be spun at a
different speed. The relevant pilot light illuminates.
Select the available options by pressing
the buttons 5 and 6
Depending on the programme, different options
can be combined. These must be selected after
choosing the desired programme and before
starting the programme. When these buttons
are pressed, the corresponding pilot lights illuminate. When they are pressed again, the pilot
lights go out. If an incorrect option is selected,
the integrated red pilot light of the button 7
flashes 3 times and the message Err is displayed.
For the compatibility among the washing programmes and the options see chapter «Washing programmes».
16
Start the programme by pressing button 7
To start the selected programme, press this
button; the corresponding green pilot light
stops blinking.
The pilot light 9 illuminates to indicate that the
appliance starts operating and the door is
locked.
If you have chosen a delayed start, the machine
will begin the countdown.
Important! If an incorrect option is selected,
the message Err is displayed for a few seconds
and the red pilot light of this button blinks 3
times.
Select the Delay Start by pressing button
8
Before you start the programme, if you wish to
delay the start, press this button to select the
desired delay.
The selected delay time value will appear on
the display for a few seconds, then the duration
of the programme will appear again.
You must select this option after you have set
the programme and before you start the programme.
You can cancel or modify the delay time at any
moment, before you press button 7.
Selecting the delay start :
1. Select the programme and the required
options.
2. Select the delay start by pressing button 8.
3. Press button 7:
- the machine starts its hourly countdown.
- the programme will start after the selected delay has expired.
Cancelling the Delay Start after having started
the programme:
1. Set the washing machine to PAUSE by
pressing button 7.
2. Press button 8 once. On the display will
appear '.
3. Press button 7 again to start the programme.
www.zanussi.com
Important!
• The selected delay can be changed only after selecting the washing programme again.
• The door will be locked throughout the delay
time. If you need to open the door, you must
first set the washing machine to PAUSE by
pressing button 7 and wait a few minutes before opening the door. After you have closed
the door, press the same button again.
Important! The Delay Start cannot be
selected with the draining programme.
Altering an option or a running
programme
It is possible to change some options before
the programme carries them out.
Before you make any change, you must pause
the washing machine by pressing button 7.
Changing a running programme is possible only
by resetting it. Turn the programme selector diand then to the new programme posial to
tion. Start the new programme by pressing button 7 again.
The washing water in the tub will be not emptied out.
Interrupting a programme
Press the button 7 to interrupt a programme
which is running, the corresponding pilot light
starts blinking. Press the button again to restart the programme.
Cancelling a programme
to cancel a proTurn the selector dial to
gramme which is running. Now you can select a
new programme.
Opening the door after the programme
has started
First set the machine to pause by pressing the
button 7.
If the pilot light 9 goes off, the door can be
opened.
If the pilot light 9 remains lit, this means that the
machine is already heating or that the water level is too high. In any case, do not force the
door!
If you cannot open the door but you need to
open it, switch the machine off by turning the
. After a few minutes the
selector dial to
door can be opened.
(Pay attention to the water level and temperature!).
After closing the door, it is necessary to select
the programme and options again and to press
button 7.
At the end of the programme
The machine stops automatically. The blinking
appears on the display, the pilot light of button 7 and the pilot light 9 go off.
If a programme or an option that ends with water left in the tub has been selected, the pilot
light 9 remains on and the door is locked to indicate that the water must be emptied out before opening the door.
Before you empty out the water, the drum continues to run at regular intervals until the water
draining.
Follow the below instructions to empty out the
water:
1. Turn the programme selector dial to
.
2.
3.
Select the draining or spinning programme.
Reduce the spin speed if needed, by
pressing the relevant button.
4. Press button 7.
At the end of the programme, the door is released and can be opened. Turn the proto switch the magramme selector dial to
chine off.
Remove the laundry from the drum and carefully
check that the drum is empty. If you do not intend to carry out another wash, close the water
tap. Leave the door open to prevent the formation of mildew and unpleasant smells.
Use - Drying
The recommended load size is 3 kg for cottons
and linen, and 2 kg for synthetic items.
Drying only
www.zanussi.com
17
Note! By pressing Drying Time button it is
also possible to dry up to 4 kg of cotton
items (see the «Drying Programme» table).
The water tap must be open and the drain
hose must be positioned in the sink or
connected to the drain pipe.
1. Load the laundry.
2. Select a spin cycle at the maximum spin
speed allowed for the type of laundry in order to obtain the best drying performances.
3. Select the drying programme for Cottons
or Synthetic in the Drying sector of the
programme selector dial.
4. If you wish to select an electronic drying,
press the button 3 until the pilot light corresponding to the required dryness degree
illuminates.
5. If you wish to select a timed drying, press
button 4 until the time you want appears on
the display (see the «Drying Programmes»
table). Every time you press this button the
drying time increases by 5 minutes.
Note!
The programme time will automatically increase by a few minutes.
6. Press button 7 to start the programme.
After the programme has started, the time
remaining is updated every minute.
Note!
The different type of cottons (towelling,
sheets, shirts, and so on) or any laundry
items rolling up during the spinning phase
may result in partial dryness. In the exceptional case that at the end of the cycle the
laundry remains slightly wet, we suggest
that you unfold the rolled up items, redistribute them evenly in the drum and select
an additional drying cycle of 20-30 minutes.
7. At the end of the programme, the buzzer
sounds and a blinking « » appear on the
display.
The last 10 minutes of the drying cycle
correspond to an anti-crease phase. During this time the door is locked and the display keeps showing the flashing zero « ».
Note!
18
If you wish to open the door before or during the anti-crease phase or to interrupt it,
press any button or turn the programme
selector dial to any programme position
), the door can be opened after
(except
a few minutes.
8.
9.
Turn the selector dial to the
switch the machine off.
Remove the laundry.
position to
Automatic washing and drying (NONSTOP programme)
For NON-STOP programmes, the recommended load size is 3 kg for cotton and 2 kg for
synthetic.
Note! It is possible to dry up to 4 kg of
cotton items by pressing Drying Time button only (see the «Drying Programme» table).
Do not use a dosing device/ball when
carrying out a washing and drying programme.
1. Load the laundry.
2. Add detergent and fabric softener.
3. Switch the machine on by turning the selector dial to the selected washing programme/fabric.
4. Select the required options by pressing the
relevant buttons.
Note!
If possible, do not select a spin speed lower than that proposed by the appliance to
avoid too long a drying time therefore saving energy.
In any case the reduction of the spin speed
is only possible after selecting drying.
5. Select the drying time by pressing the button 4 or dryness degree by pressing the
button 3. The display shows the entire duration of the washing and the selected drying cycle.
6. Start the programme by pressing button 7.
After the programme has started, the time
remaining is updated every minute.
7. At the end of the programme the buzzer
sounds. A flashing zero « » appear on
www.zanussi.com
the display. At this point of the programme,
starts an anti-crease phase which lasts
about 10 minutes. During this time the
door is locked and the display keeps
showing the flashing zero « ». (If you
wish to open the door before or during the
Fluff in the garments
During the WASHING AND/OR DRYING
PHASE, certain types of fabric, as spongecloth, sweatshirt, could release fluff.
The released fluff could stick to the fabrics during the next cycle.
This drawback increases with technical fabrics.
To prevent the lint in your clothes, it is recommended:
• To do not wash dark fabrics after you washed and dried light coloured fabrics (new
anti-crease phase, please follow the instructions given in the previous chapter).
8.
9.
•
•
•
•
Turn the selector dial to the
switch the machine off.
Remove the laundry.
position to
sponge, sweatshirt especially) and vice versa.
To air-dry this type of fabrics when they are
washed the first time.
To clean the filter.
Perform one or more rinse cycles to wash the
drum between the washing and drying of
fabrics with different colours.
After the drying phase, thoroughly clean the
empty drum, the gasket and the door with a
wet rag.
Care and cleaning
Warning! You must DISCONNECT the
appliance from the electricity supply,
before you can carry out any cleaning or
maintenance work.
Descaling
The water we use normally contains lime. It is a
good idea to periodically use a water softening
powder in the machine. Do this separately from
any laundry washing, and according to the softening powder manufacturer's instructions. This
will help to prevent the formation of lime deposits.
External cleaning
Clean the exterior cabinet of the appliance with
soap and water only, and then dry thoroughly.
Cleaning the dispenser drawer
The washing powder and additive dispenser
drawer should be cleaned regularly.
www.zanussi.com
Remove the drawer
by pressing the catch
downwards and by
pulling it out. Flush it
out under a tap, to remove any traces of
accumulated powder.
To aid cleaning, the
top part of the additive compartment
should be removed.
Cleaning the drawer recess
Having removed the
drawer, use a small
brush to clean the recess, ensuring that all
washing powder residue is removed from
the upper and lower
part of the recess.
19
Replace the drawer and run the rinse programme without any clothes in the drum.
Cleaning the pump
The pump should be inspected regularly and
particularly if:
• the appliance does not empty and/or spin;
• the appliance makes an unusual noise during
draining due to objects such as safety pins,
coins etc. blocking the pump;
• a problem with water draining is detected
(see chapter “What to do if...” for more details).
1.
2.
Warning!
Disconnect the mains plug from the mains
socket.
Do not remove the filter while the appliance
operates. Do not clean the drain pump if
the water in the appliance is hot. The water
must be cold before you clean the drain
pump.
When the container is full of water, put the
drainage duct back again and empty the container. Do steps 3 and 4 again and again until
no more water flows out from the drain pump.
1
2
Pull back the drainage duct.
Unscrew the filter and remove it.
Proceed as follows:
Remove fluff and objects from the pump.
Open the pump door.
Put a container below the recess of the drain
pump to collect the water that flows out.
Make sure that the impeller of the pump can
turn. If this does not occur, contact the service centre.
Press the two levers and pull forward the
drainage duct to let the water flow out.
20
www.zanussi.com
• Turn off the water
tap.
• Unscrew the hose
from the tap.
• Clean the filter in
the hose with a stiff
brush.
1
2
Clean the filter under the water tap and put it
back in the pump into the special guides.
Make sure that you tighten correctly the filter
to prevent leakages.
Close the pump door.
Caution! When the appliance is in use
and depending on the programme
selected there can be hot water in the pump.
Never remove the pump cover during a wash
cycle, always wait until the appliance has
finished the cycle, and is empty. When refitting
the pump cover, ensure it is securely retightened so as to stop leaks and young
children being able to remove it.
Cleaning the water inlet filters
Important! If the appliance doesn't fill, takes
long to fill with water, the starting button blinks
yellow or the display (if available) shows the
relevant alarm (see chapter "What to do if..." for
more details), check if the water inlet filters are
blocked .
To clean the water inlet filters:
www.zanussi.com
• Screw the hose back onto the tap. Make
sure the connection is tight.
• Unscrew the hose from the machine. Keep
a rag nearby because some water may
flow.
• Clean the filter in the valve with a stiff
brush or with the piece of cloth.
35°
45°
• Screw the hose back to the machine and
make sure the connection is tight.
• Turn on the water tap.
Frost precautions
If the machine is installed in a place where the
temperature could drop below 0°C, remove the
remaining water from the inlet hose and the
drain pump.
1. disconnect the mains plug from the mains
socket.
2. close the water tap
3. unscrew the water inlet hose from the tap;
21
4.
5.
6.
put the two ends of the inlet hose in a container and let the water flow out of the
hose.
empty the drain pump as described in the
‘Emergency emptying out’ section.
when the drain pump is empty, install the
water inlet hose again.
Warning!
Make sure that the temperature is more than 0
°C before you use the appliance again.
The manufacturer is not responsible for damages caused by low temperatures.
Emergency emptying out
If the appliance cannot drain the water, proceed as follows to empty out the machine:
1. pull out the plug from the power socket;
2. close the water tap;
3. if necessary, wait until the water has
cooled down;
4.
5.
open the pump door;
place a container on the floor below the recess of the drain pump;
6. press the two levers and pull forward the
drainage duct to let the water flow out;
7. when the container is full of water, put the
drainage duct back again and empty the
container;
repeat this operation until water stops
flowing out;
8. if necessary clean the pump (refer to the
section ‘Cleaning the pump’ );
9. close the drain pump door.
When you drain the water with the emergency
drain procedure, you must activate again the
drain system:
1. Put 2 litres of water in the main wash compartment of the detergent dispenser.
2. Start the programme to drain the water.
What to do if…
Certain problems are due to lack of simple
maintenance or oversights, which can be
solved easily without calling out an engineer.
Before contacting your local Service Centre,
please carry out the checks listed below.
During machine operation it is possible that the
red pilot light of button 7 blinks, one of the following alarm codes appears on the display and
some acoustic signals sound every 20 seconds
to indicate that the machine is not working:
22
•
: problem with the water supply.
•
: problem with the water draining.
•
: door open.
Once the problem has been eliminated, press
the button 7 to restart the programme. If after
all checks, the problem persists, contact your
local Service Centre.
www.zanussi.com
Problem
Possible cause/Solution
The washing machine does
not start:
The door has not been closed.
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The selector dial is not correctly positioned and/or the button 7 has not
been pressed.
• Please turn the selector dial and press the button 7 again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay start.
The Child Safety Lock has been activated.
• Deactivate the Child Safety Lock.
The machine does not fill:
The water tap is closed.
• Open the water tap.
The inlet hose is squashed or kinked.
• Check the inlet hose connection.
The filter in the inlet hose or in the inlet valve filter are blocked.
• Clean the water inlet filters (see ‘Cleaning the water inlet filters’ for
more details).
The door is not properly closed.
• Close the door firmly.
The machine fills then empties immediately:
The end of the drain hose is too low.
• Refer to relevant paragraph in «Water drainage» section.
The machine does not empty
and/or does not spin:
The drain hose is squashed or kinked.
• Check the drain hose connection.
The drain filter is clogged.
• Clean the drain filter.
An option or a programme that ends with the water still in the tub or that
eliminates all the spinning phases has been selected.
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
www.zanussi.com
23
Problem
Possible cause/Solution
There is water on the floor:
Too much detergent or unsuitable detergent (creates too much foam)
has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fittings. It is
not always easy to see this as the water runs down the hose; check to
see if it is damp.
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Replace it with a new one.
The filter has not been properly screwed in after cleaning action.
• Screw the filter fully in.
Unsatisfactory washing results:
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
The door will not open:
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the door is released.
There is water in the drum.
• Select drain or spin programme to empty out the water.
The machine vibrates is
noisy:
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
Spinning starts late or the
machine does not spin:
The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by
reverse rotation of the drum. This may happen several times before the
unbalance disappears and normal spinning can resume. If, after 10 minutes, the laundry is still not evenly distributed in the drum, the machine
will not spin. In this case, redistribute the load manually and select the
spin programme.
• Redistribute the laundry.
The load is too small.
• Add more items, redistribute the load manually and then select the
spinning programme.
24
www.zanussi.com
Problem
Possible cause/Solution
The machine makes an unusual noise:
The machine is fitted with a type of motor which makes an unusual noise
compared with other traditional motors. This new motor ensures a softer
start and more even distribution of the laundry in the drum when spinning, as well as increased stability of the machine.
No water is visible in the
drum:
Machines based on modern technology operate very economically using
very little water without affecting performance.
The machine does not dry or
does not dry properly:
The drying time or the dryness degree has not been selected.
• Select the drying time or the dryness degree.
The water tap is not turned on.
• Open the water tap.
The drain filter is clogged.
• Clean the drain filter.
The machine is overloaded.
• Reduce the laundry load in the drum.
The selected drying programme, time or dryness degree was not suitable for the laundry.
• Select the suitable drying programme, time or dryness degree for the
laundry.
The laundry is full of different colored fluff:
The fabrics washed in the previous cycle released fluff of a different color (refer to “Fluff in the garments” in chapter “Use - Washing & Drying”).
• The drying phase helps to eliminate some fluff.
• Clean the clothes with a fluff remover.
In case of an excessive amount of fluff in the drum repeat the following
procedure twice:
• Thoroughly clean the empty drum, the gasket and the door with a wet
rag.
• Perform a rinse cycle.
• Put a wool or piled fabric rag inside the drum.
• Perform a drying cycle of 10 minutes.
• Remove the old wool cloth.
Now you can wash other garments.
If you are unable to identify or solve the problem, contact our service centre. Before telephoning, make a note of the model, serial number and purchase date of your machine: the
Service Centre will require this information.
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ...
Technical data
Dimensions
www.zanussi.com
Width
Height
Depth
60 cm
85 cm
63 cm
25
Electrical connection
Voltage - Overall power - Fuse
Information on the electrical connection is given on the rating plate, on
the inner edge of the appliance door.
Water Supply Pressure
Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load
Cotton
6 kg
Maximum Dry Load
Cotton
Cotton Big Capacity
Synthetic
3 Kg
4 Kg
2 Kg
Spin Speed
Maximum
1600 rpm (ZKG 7165)
1400 rpm (ZKG 7145)
1200 rpm (ZKG 7125)
Consumption values
Programme
Energy consumption
(KWh)
Water consumption
(litres)
Programme duration
(Minutes)
Cottons 60°
1.30
58
Cotton Energy Saving
Programme 60° 1)
1.02
46
Cottons 40°
0.70
58
For the duration of
the programmes,
please refer to the
display on the control
panel.
Synthetics 40°
0.50
50
Delicates 40°
0.55
60
Wool/ Handwash 30°
0.25
53
1) «Cotton Energy Saving programme » at 60°C with a load of 6 kg is the reference programme for the data
entered in the energy label, in compliance with EEC 92/75 standards.
The consumption data shown on this chart is to be considered purely indicative, as it may vary
depending on the quantity and type of laundry, on the inlet water temperature and on the ambient temperature.
Installation
Rubber feet kit (4055126249)
Available from your authorized dealer.
The rubber feet are particularly recommended
on floating, slippery and wooden floors.
Mount the rubber feet to prevent vibration,
noises and displacement of the appliance during operation.
Read carefully the instructions supplied with
the kit.
If you install the appliance on a plinth, secure
the appliance in the fixing plates.
Follow the instructions supplied with the kit.
Unpacking
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all transit devices so
that they can be refitted if the machine ever has
to be transported again.
Fixing plate kit (4055171146)
Available from your authorized dealer.
26
www.zanussi.com
After removing all the
packaging, carefully
lay machine on it's
back to remove the
polystyrene base
from the bottom.
Unscrew the three
bolts.
Remove the power
supply cable and the
hose from the hose
holders on the rear of
the appliance.
Slide out the relevant
plastic spacers.
raising or lowering the feet. The feet may be
tight to adjust as they incorporate a self locking
nut, but the machine MUST be level and stable.
Any necessary adjustment can be made with a
spanner.
Accurate levelling prevents vibration, noise and
displacement of the machine during operation.
Never place cardboard, wood or similar materials under the machine to compensate for any
unevenness in the floor.
If necessary, check
the setting with a spirit level.
Installation on suspended flooring
Suspended wooden floors are particularly susceptible to vibration.
To help prevent vibration we recommend you
place a waterproof wood panel, at least 15 mm
thick under the appliance, secured to at least 2
floor beams with screws, the wood panel must
extend beyond the front feet.
If possible install the appliance in one of the
corners of the room, where the floor is more
stable.
Water inlet
Open the porthole,
remove the polystyrene block fitted on
the door seal and pull
out all items from the
drum.
Fill the smaller upper
hole and the two
large ones with the
corresponding plastic
plug caps supplied in
the bag containing
the instruction booklet.
Positioning
Install the machine on a flat hard floor. Make
sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that
the machine does not touch the wall or other
kitchen units. Level the washing machine by
www.zanussi.com
Warning! This appliance must be
connected to a cold water supply
Caution! Before connecting up the
appliance to new pipework or to pipework
that has not been used for some time, run off a
reasonable amount of water to flush out any
debris that may have collected
Caution! Do not use the hose from your
previous appliance to connect to water
supply.
The inlet hose is delivered with the machine.
27
• Connect the appropriate end of
the hose to a tap
with a 3/4” thread.
Always use the
hose supplied with
the appliance.
There should be a minimum vertical distance of
5.02 m (16.5 ft) between the appliance’s inlet
and the bottom of the water storage tank.
Water drainage
This appliance is designed to be permanently
plumbed into your home's drainage system using one of the following methods.
1. Into a drainage standpipe.
Firstly form a hook in the end of the drain
hose using the “U” piece” supplied.
35°
45°
• Connect the other end of the inlet hose to
the back of the appliance. The inlet hose
can be turned as showed in the picture.
Do not place the inlet hose downwards. Angle the hose to the left or right
depending on the position of your water
tap. Set the hose correctly by loosening
the ring nut. After positioning the inlet
hose, be sure to tighten the ring nut again
to prevent leaks.
Caution! The inlet hose must not be
lengthened. If it is too short and you do not
wish to move the tap, you will have to purchase
a new, longer hose specially designed for this
type of use.
Warning! Installation should comply
with local water authority and
building regulations’ requirements.
The appliance must be connected to a
cold water supply.
A minimum water pressure of 0.05 MPa (0.5
bar) is required for safe operation of the
appliance.
If you cannot make the cold water connection
direct from the rising mains, you may be able to
operate the appliance from your cold water
storage system.
28
“U” piece supplied
Place the drain hose into your standpipe,
which should have an internal diameter of approximately 38 mm thus ensuring there is an
air break between the drain hose and standpipe.
When discharging into a standpipe ensure
that the top of the standpipe is no more than
90 cm (35.4'') and no less than 60 cm (23.6'')
above floor level.
38 mm (1.5”)
standpipe
diamater
30 cm (12”)
The drain hose may be extended to a maximum of 4 metres. An additional drain hose
and joining piece is available from your local
Service Force Centre. The joining piece must
have an internal diameter of 18 mm.
www.zanussi.com
If you intend to drain the hose from the machine into a sink, make sure that the sink is
empty and the plug hole is not blocked. Use
the plastic “U - Piece” supplied.
Min. 60 cm (23.6”)
Max. 90 cm (35.4”)
If your drain hose
looks like this (see
beside) you do not
require the “U”
piece”. Just push the
hose firmly in to the
standpipe.
In the interest of the environment
The appliance should be connected to the
FOUL drainage system, the water will then be
taken to a sewage works for treatment before
being discharged safely into a river.
It is essential that these appliances are not connected to the surface water drainage system as
this water is discharged directly into a river or
stream and may cause pollution.
If you require any further advice please contact
your local water authority.
2. Onto a sink outlet spigot.
SHOWER
SINK TOILET
BATH
Loop
If the outlet spigot
has not been used
before, remove any
blanking plug that
may be in place.
Push the drain hose
onto the spigot and
secure with a clip,
ensure a loop is
formed in the drain
hose (see above) to
prevent waste from
the sink entering the
appliance.
BIDET
WASHING
MACHINE
DISHWASHER
RAINWATER
‘RUN-OFF’
SURFACE WATER
DRAINS & SEWERS
UNTREATED
DISCHARGE
RIVER
FOUL DRAIN
FOUL SEWERS
SEWAGE TREATMENT
WORKS
TREATED DISCHARGE
RIVER
Environment concerns
The symbol on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it
should be taken to the appropriate collection
point for the recycling of electrical and
electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent
www.zanussi.com
potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed
information about recycling of this product,
please contact your local council, your
29
household waste disposal service or the shop
where you purchased the product.
Packaging materials
are
The materials marked with the symbol
recyclable.
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by disposing of them properly in appropriate collection containers.
• Normally soiled laundry may be washed without prewashing in order to save detergent,
water and time (the environment is protected
too!).
• The machine works more economically if it is
fully loaded.
• With adequate pre-treatment, stains and limited soiling can be removed; the laundry can
then be washed at a lower temperature.
• Measure out detergent according to the water hardness, the degree of soiling and the
quantity of laundry being washed.
Ecological hints
To save water, energy and to help protect the
environment, we recommend that you follow
these tips:
30
www.zanussi.com
www.zanussi.com
31
132937921-A-432012
www.zanussi.com/shop

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement