EN
User manual
Washing Machine
ZWG 6144 PS
Contents
Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _
Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _
Frost precaution _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Environment concerns _ _ _ _ _ _ _ _ _ _ _ _
Product description _ _ _ _ _ _ _ _ _ _ _ _ _
Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2
3
4
5
6
7
7
First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Washing programmes _ _ _ _ _ _ _ _ _ _ _
Consumption values _ _ _ _ _ _ _ _ _ _ _ _
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _
What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
12
12
19
21
22
24
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always
keep the instructions with the appliance for future reference.
Children and vulnerable people safety
Warning! Risk of suffocation, injury or permanent disability.
• Do not let persons, children included, with reduced physical sensory, reduced mental functions or lack of experience and knowledge use the appliance. They must have supervision or instruction
for the operation of the appliance by a person who is responsible
for their safety.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep all detergents away from children.
• Keep children and pets away from the appliance door when it is
open.
• If the appliance has a child safety device, we recommend you activate it.
General Safety
• Before maintenance, deactivate the appliance and disconnect the
mains plug from the mains socket.
• Do not change the specification of this appliance.
2
www.zanussi.com
• Obey the maximum load volume of 6 kg (refer to the “Programme
chart” chapter).
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to
avoid a hazard.
• The operating water pressure (minimum and maximum) must be
between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa)
• The ventilation openings in the base (if applicable) must not be
obstructed by a carpet.
• The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.
Safety instructions
Installation
• Remove all the packaging and the transit
bolts.
• Keep the transit bolts. When you move the
appliance again you must block the drum.
• Do not install or use a damaged appliance.
• Do not install or use the appliance where the
temperature is less than 0 °C or where it is
exposed to the weather.
• Obey the installation instruction supplied
with the appliance.
• Make sure that the floor where you install the
appliance is flat, stable, heat resistant and
clean.
• Do not install the appliance where the appliance door can not be fully opened.
• Always be careful when you move the appliance because it is heavy. Always wear safety
gloves.
• Make sure that there is air circulation between the appliance and the floor.
• Adjust the feet to have the necessary space
between the appliance and the carpet.
Electrical connection
Warning! Risk of fire and electrical shock.
www.zanussi.com
• The appliance must be earthed.
• Make sure that the electrical information on
the rating plate agrees with the power supply. If not, contact an electrician.
• Always use a correctly installed shockproof
socket.
• Do not use multi-plug adapters and extension cables.
• Make sure not to cause damage to the mains
plug and to the mains cable. Should the appliance power supply cable need to be replaced, this must be carried out by our Service Centre.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after
the installation.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
• Do not touch the mains cable or the mains
plug with wet hands.
• Only for UK and Ireland. The appliance has a
13 amp mains plug. If it is necessary to
change the fuse in the mains plug, use a 13
amp ASTA (BS 1362) fuse.
•
3
This appliance complies with the E.E.C. Directives.
Water connection
• Make sure not to cause damage to the water
hoses.
• The appliance is to be connected to the water mains using the new supplied hose-sets.
Old hose sets must not be reused.
• Before you connect the appliance to new
pipes or pipes not used for a long time, let
the water flow until it is clean.
• The first time you use the appliance, make
sure that there is no leakage.
Use
Warning! Risk of injury, electrical shock,
fire, burns or damage to the appliance.
• Use this appliance in a household environment.
• Obey the safety instructions on the detergent
packaging.
• Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
• Do not touch the glass of the door while a
programme operates. The glass can be hot.
• Make sure that you remove all metal objects
from the laundry.
• Do not put a container to collect possible
water leakage under the appliance. Contact
the Service to ensure which accessories can
be used.
Care and Cleaning
Warning! Risk of injury or damage to the
appliance.
• Do not use water spray and steam to clean
the appliance.
• Clean the appliance with a moist soft cloth.
Only use neutral detergents. Do not use
abrasive products, abrasive cleaning pads,
solvents or metal objects.
Disposal
Warning! Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children
and pets to get closed in the appliance.
Frost precaution
If the appliance is installed in a place where the
temperature could drop below 0°C, proceed as
follows to remove any water remaining inside
the appliance:
1. unplug the appliance;
2. turn off the water tap;
3. unscrew the water inlet hose from the tap;
4. unscrew the drain hose from the rear support and unhook it from sink or spigot;
5.
6.
7.
4
place a bowl on the floor;
let the drain hose run along the floor, place
the external extremities of the drain and inlet hoses in the bowl placed on the floor
and let water drain out completely;
screw the water inlet hose to the tap and
the drain hose to the rear of the appliance
again;
www.zanussi.com
When you intend to start the appliance up
again, make sure that the room temperature is
above 0°C.
Environment concerns
The symbol on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it
should be taken to the appropriate collection
point for the recycling of electrical and
electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent
potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed
information about recycling of this product,
please contact your local council, your
household waste disposal service or the shop
where you purchased the product.
Packaging materials
The materials marked with the symbol
recyclable.
>PE<=polyethylene
>PS<=polystyrene
www.zanussi.com
are
>PP<=polypropylene
This means that they can be recycled by disposing of them properly in appropriate collection containers.
Ecological hints
To save water, energy and to help protect the
environment, we recommend that you follow
these tips:
• Normally soiled laundry may be washed without prewashing in order to save detergent,
water and time (the environment is protected
too!).
• The machine works more economically if it is
fully loaded.
• With adequate pre-treatment, stains and limited soiling can be removed; the laundry can
then be washed at a lower temperature.
• Measure out detergent according to the water hardness, the degree of soiling and the
quantity of laundry being washed.
5
Product description
1
2
7
3
11
8
9
4
9
9
10
5
12
6
1 Detergent dispenser drawer
7 Water drain hose
2 Worktop
8 Drain hose support
3 Control panel
9 Hose holders
4 Door opening handle
10 Water inlet hose
5 Rating plate (on the inner edge)
11 Mains cable
6 Front adjustable feet
12 Back feet
Child safety device
To activate this device, rotate the button
To disable this device and restore the possi(without pressing it) inside the door clockwise bility of closing the door, rotate the button antiuntil the groove is horizontal. If necessary use a clockwise until the groove is vertical.
coin.
6
www.zanussi.com
Technical data
Dimensions
Width
Height
Depth
60 cm
85 cm
54 cm
Electrical connection
Voltage - Overall power - Fuse
Information on the electrical connection is given on the rating plate, on
the inner edge of the appliance door.
Water supply pressure
Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load
Cotton
6 kg
Spin Speed
Maximum
1400 rpm
Installation
Unpacking
• Remove the external film. Use a cutter, if necessary.
Warning!
• Read carefully the "Safety information"
chapter before installing the appliance.
x3
A
B
x3
x1
C
x2
Warning! Remove and keep all
transit devices so that they can be refitted if the appliance ever has to be transported again.
Necessary tools
• Remove the cardboard top.
• Remove the polystyrene packaging materials.
1
10 mm
30 mm
www.zanussi.com
2
• Spread the front
piece on the floor
behind the appliance and then lay
the appliance carefully rear side down
on it. Make sure
that no hoses are
crushed in the
process.
7
• Remove the polystyrene base from the bottom.
• Return appliance
to it's upright position.
• Open the door and
remove the plastic
hose guide, the
bag containing the
instruction booklet
and the plastic
plug caps from the
drum.
• Unscrew the three bolts and remove the
hose holders.
• Slide out the relevant plastic spacers.
Warning! Do
not remove
the drain hose
from the rear support. Remove this
hose only if it is
necessary to drain
the water. Refer to
"Frost precaution"
and "What to do if".
• Remove the power supply cable and the
draining and inlet hose from the hose holders on the rear of the appliance.
• Plug the smaller upper hole and the two
large ones with the corresponding plastic
plug caps.
8
www.zanussi.com
Positioning and levelling
Water inlet
Connect the hose to
a tap with a 3/4”
thread.
35°
45°
x4
Level the appliance by raising or lowering the
feet.
The appliance MUST be level and stable on a
flat hard floor. If necessary, check the setting
with a spirit level. Any necessary adjustment
can be made with a spanner.
Loosen the ring nut to angle the hose to the
left or right depending on the position of your
water tap. Do not place the inlet hose
downwards. After positioning the inlet hose,
be sure to tighten the ring nut again to prevent leaks.
Water drainage
Accurate levelling prevents vibration, noise
and displacement of the appliance during operation.
Repeat the levelling action, if the appliance is
not level and stable.
Warning! This appliance is free standing
only. Do not remove the worktop for any
reason.
www.zanussi.com
Firstly form a hook in the end of the drain
hose using the plastic hose guide supplied
with the appliance .
The end of the drain hose can be positioned
in four ways:
• Hooked over the edge of a sink using
the plastic hose guide.
9
MAX 100cm
Tie the plastic hose guide to the tap with a
string to prevent that the drain hose unhooks
when the appliance is emptying.
• Onto a sink outlet spigot.
The end of the drain
hose must always be
ventilated, i.e. the
inside diameter of the
drain pipe must be
larger than the outside diameter of the
drain hose. The drain
hose must not be
kinked.
If your drain hose
looks like this (see
beside) you do not
require the “U”
piece”. Just push the
hose firmly in to the
standpipe.
• Directly to a built-in drain pipe in the
room wall.
Push the drain hose onto the spigot and secure with a clip, ensure a loop is formed in
the drain hose to prevent waste from the sink
entering the appliance.
If the outlet spigot has not been used before,
remove any blanking plug that may be in
place.
• Directly into a drain pipe at a height of
not less than 60 cm and not more than
100 cm.
10
The drain hose may be extended to a maximum of 4 metres. An additional drain hose
and joining piece is available from your Local
Centre.
www.zanussi.com
Connections overview
0.5 bar (0.05 MPa)
8 bar (0.8 MPa)
max.
100 cm
min. 60 cm
max. 100 cm
min.
60 cm
~max.400 cm
In the interest of the environment
The appliance should be connected to the
FOUL drainage system, the water will then be
taken to a sewage works for treatment before
being discharged safely into a river.
It is essential that these appliances are not connected to the surface water drainage system as
this water is discharged directly into a river or
stream and may cause pollution.
If you require any further advice please contact
your local water authority.
SHOWER
SINK TOILET
BATH
BIDET
WASHING
MACHINE
DISHWASHER
RAINWATER
‘RUN-OFF’
SURFACE WATER
DRAINS & SEWERS
UNTREATED
DISCHARGE
RIVER
www.zanussi.com
FOUL DRAIN
Electrical connection
• The appliance must be earthed.
• Make sure that the electrical information on
the rating plate agree with your domestic
power supply.
• Always use a correctly installed shockproof
socket.
• Do not use multi-way plugs, connectors and
extension cables. There is a risk of fire.
• Do not replace or modify the mains cable
yourself. Contact the After Sales Service.
• Make sure that the mains plug and cable is
not squashed or damaged by the back of the
appliance.
• The mains plug must be accessible without
moving machine to enable electrical isolation
of appliance prior to cleaning or service.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
• This appliance complies with the E.E.C. Directives.
FOUL SEWERS
SEWAGE TREATMENT
WORKS
TREATED DISCHARGE
RIVER
11
Warning! The appliance is supplied with
a 13 amp plug attached. Use a 13 amp
ASTA approved (BS 1362) fuse if it is
necessary to change the fuse in the plug
supplied. A cut off plug inserted into a 13 amp
socket is a serious safety danger. Make sure
that it is disposed of safely.
First use
• Ensure that the electrical and water
connections comply with the installation
instructions.
• Ensure that the drum is empty.
laundry in the machine, to remove any
manufacturing residue from the drum
and tub. Pour 1/2 a measure of detergent into the main wash compartment
and start the machine.
• Before the first wash, run a cotton cycle
at the highest temperature without any
Daily use
Sort out the laundry
Follow the wash code symbols on each garment label and the manufacturer’s washing instructions. Sort the laundry as follows: whites,
coloureds, synthetics, delicates, woollens.
Before Loading The Laundry
Important! Make
sure that no metal
objects are left in the
laundry (e.g. hair
clips, safety pins,
pins). Button up pillowcases, close zip
fasteners, hooks and
poppers. Tie any
belts or long tapes.
Remove any hooks
(e.g curtains).
• Never wash whites and coloureds together.
Whites may lose their «whiteness» in the
wash.
• New coloured items may run in the first
wash; they should therefore be washed separately the first time.
• Rub particularly soiled areas with a special
detergent or detergent paste.
• Treat curtains with special care.
• Wash the socks and the gloves inside the
bag or a net.
Remove stubborn stains before washing:
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a special detergent then rub in the soap and water.
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and
dab the stain; treat several times.
Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the
stain with the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since the
cellulose structure will already have been damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with acetone1), lay the garment on a soft cloth and dab
the stain.
Lipstick: moisten with acetone as above, then
treat stains with methylated spirits. Treat any residual marks with bleach.
1) do not use acetone on artificial silk.
12
www.zanussi.com
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten the
fabric first with acetone1), then with acetic acid;
treat any residual marks on white fabrics with
bleach and then rinse thoroughly.
Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with detergent paste.
Open the door by carefully pulling the
door handle outwards
Load the laundry
Place the laundry in
the drum, one item at
a time, shaking them
out as much as possible.
Maximum Loads
Recommended loads are indicated in the
«Washing Programmes».
General rules:
• Cotton, linen: drum full but not too tightly
packed;
• Synthetics: drum no more than half full;
• Delicate fabrics and woollens: drum no
more than one third full.
Close the door gently
Warning! Make
sure that any
fabrics were not trapped when closing the
door.
www.zanussi.com
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the environment.
Although biodegradable, detergents contain
substances which, in large quantities, can upset the delicate balance of nature.
The choice of detergent will depend on the
type of fabric (delicates, woollens, cottons,
etc.), the colour, washing temperature and degree of soiling.
All commonly available washing machine detergents may be used in this appliance:
• powder detergents for all types of fabric,
• powder detergents for delicate fabrics (40°C
max) and woollens,
• liquid detergents, preferably for low temperature wash programmes (60°C max) for all
types of fabric, or special for woollens only.
The detergent dispenser drawer is provided with an insert for liquid detergent. Do
not use the insert downwards for gelatinous
detergents, with programmes including prewash, with the delay start option. In all these
cases you can use metering balls or sachets
provided with the detergent, Take out the metering aid at the end of the washing cycle.
Quantity of detergent to be used
The type and quantity of detergent will depend
on the type of fabric, load size, degree of soiling
and hardness of the water used.
For the quantity of detergent, refer always to
what is written on the product packing.
Use less detergent if:
• you are washing a small load,
• the laundry is lightly soiled,
• large amounts of foam form during washing.
Degrees of water hardness
Water hardness is classified in so-called “degrees” of hardness. Information on hardness of
the water in your area can be obtained from the
relevant water supply company, or from your local authority.
13
If the water hardness degree is medium or high
we suggest you to add a water softener following always the manufacturer’s instructions.
When the degree of hardness is soft, readjust
the quantity of the detergent.
Open the detergent dispenser drawer
Compartment for
powder or liquid detergent used for main
Compartwash.
ment for liquid additives (fabric softener,
starch).
Warning! If you wish to carry out the
prewash, pour the detergent for prewash
phase among washing items into the drum.
Warning! Depending on the type
detergent you use (powder of liquid),
ensure that the flap, placed in the main wash
compartment, is in the desired position.
Flap for powder or liquid detergent
PU
SH
DOWN - Flap position if using LIQUID detergent during main wash
RE
TO MOV
CL E
EA
N
SH
PU
RE
TO MOV
CL E
EA
N
UP- Flap position
if using POWDER
detergent
• Remove the drawer. Push the drawer edge
outwards where indicated by the arrow
(PUSH) to facilitate drawer removal.
The flap is down and you wish to use
powder detergent:
• Rotate the flap upwards. Ensure to fit
the flap completely
in.
• Carefully put the
drawer back.
• Measure out the
detergent.
• Pour the powder
detergent into the
main wash com.
partment
The flap is up and you wish to use liquid
detergent:
• Rotate the flap
downwards.
• Carefully put the
drawer back.
If the flap is not in the desired position:
• Measure out the detergent.
For the quantity of detergent, refer always to what is written on the product
packing and ensure that the detergent can be
poured in the drawer.
14
www.zanussi.com
• Pour the liquid detergent in the compartwithout exceeding the limit indicament
ted in the flap. The detergent must be
placed in the appropriate compartments of
the dispenser drawer before starting the
wash programme.
•
•
•
•
Measure out the fabric softener
Pour fabric softener
or any additives into
the compartment
(do not
marked
exceed the «MAX»
mark in the drawer).
Any additives must
be placed in the appropriate compartments of the dispenser drawer just before
starting the wash programme.
Warning! Do not use the flap in "DOWN"
position with:
Gelatinous detergent or thick detergent.
Powder detergent.
With programmes with prewash.
Do not use liquid detergent if the washing
programme doesn't start immediately.
Close the detergent dispenser drawer
In all above listed cases, use the flap in
"UP" position .
Set your washing programme
The control panel permits to select a washing programmes and different options.
When an option button is selected, the corresponding pilot light is on. Otherwise it is off.
For compatibility among washing programmes and options, see the "Washing Programme
Chart". If an incorrect option is selected, the integrated red pilot light of the button 6 flashes
3 times.
5
1
www.zanussi.com
2
3
4
6
7
15
1
Programme selector di- Turn the programme selector dial to the required proal
gramme. The selector dial can be turned either clockwise or counter-clockwise. The green pilot light of the button 6 starts flashing: the appliance is now switched on.
Specials
Cottons
Jeans
Cottons
+Prewash
Mini 30
Cottons Eco
5 Shirts
Easy Iron
Synthetics
Spin
Mixed Fabric
Drain
Delicates
Rinse
Wool
Handwash
If you turn the programme selector dial to another programme when the appliance is working, the red pilot light
of the button 6 will flash 3 times to indicate a wrong selection.
The appliance will not perform the new selected programme.
• To switch the appliance off, turn the programme selector
.
dial to the position
• To cancel or change a running programme, switch the appliance off by turning the programme selector dial to the
. Select the new programme by turning the seposition
lector to the desired programme. Start the new programme
by pressing the button 6 again. The water in the tub will be
not emptied out.
2
Temperature button
Push the temperature button to select the most suitable temperature for washing your laundry .
3
Automatic Spin reduction and Rinse Hold
By selecting a programme, the appliance proposes automatically the maximum spin speed provided for that programme.
) the spin speed is
By selecting Automatic Spin reduction (
reduced to a half, but not less than 400 rpm. The relevant light
illuminates.
Rinse Hold
By selecting this function the water of the last rinse is not
emptied out to prevent the fabrics from creasing. Before
opening the door it will be necessary to empty out the water.
To empty out the water, please read the paragraph «At
the end of the programme».
Spin
4
Super Quick
Super
Quick
16
By pressing this button the corresponding pilot light illuminates.
Short cycle for lightly soiled items or for laundry which needs
only freshening up.
With this option, a reduced load of laundry is recommended:
• Cottons 3 kg
• Synthetics and delicates 1,5 kg
www.zanussi.com
3
Extra Rinse
+
Super
Quick
4
Spin
5
Delay Start
Delay Start
3h
6h
9h
This appliance is designed for saving water. However, for people with very delicate skin (allergic to detergents) it may be
necessary to rinse the laundry using an extra quantity of water.
Press simultaneously the buttons 3 and 4 for some seconds:
the pilot light 7.2 comes on. This function stays permanently
on. To remove it press the same buttons again until the pilot
light 7.2 goes off.
The start of the programme can be delayed by 9, 6 or 3 hours
by means of this button. The relevant light illuminates.
You must select this option after you have set the programme
and before you start the programme.
Select a delayed start:
• select the programme and the required options;
• select the delay start by pressing the button 5;
• press the button 6:
– the appliance starts its hourly countdown.
– The programme will start after the selected delay has expired.
Cancelling the delayed start after having started the
programme:
• set the appliance to PAUSE by pressing the button 6;
• press the button 5 once, the light relevant to the selected
delay goes off;
• press the button 6 again to start the programme.
The DELAY START cannot be selected with the drain programme.
Important! The selected delay can be changed only after selecting the washing programme again. The door will be locked
throughout the delay time. If you need to open the door, you
must set the appliance to PAUSE (by pressing the button 6)
and then wait a few minutes. After you have closed the door,
press the button 6 again.
www.zanussi.com
17
6
Start/Pause
Start /Pause
Start the programme by pressing the button 6
• To start the selected programme, press the button 6, the
corresponding green pilot light stops flashing. The pilot light
7.1 illuminates to indicate that the appliance starts operating and the door is locked. If you have chosen a delayed
start, the appliance will begin the countdown.
• To interrupt a programme which is running, press the button 6: the corresponding green pilot light starts flashing. It
is possible to change some options of a running programme before the programme carries them out.
• To restart the programme from the point at which it was interrupted, press the button 6.
• After the programme has started the door is locked. If, for
any reason, you need to open the door, set firstly the appliance to PAUSE by pressing the button 6. After a few minutes it will be possible to open the door.
If the door remains locked, this means that the appliance is
already heating or that the water level is too high. In any
case, do not try to force the door!
If you cannot open the door but you need to open it you
have to switch the appliance off by turning the selector dial
. After a few minutes the door can be opened (pay
to
attention to the water level and temperature!). After
closing the door, it is necessary to select the programme
and options again and to press the button 6.
Indicator pilot lights
,
.
7.1
7.2
7.3
• When you start the programme by pressing the button 6,
the washing phase pilot light (7.1) illuminates. This means
that the appliance is operating.
• The additional rinses pilot light (7.2) illuminates when the
appliance performs an extra rinse.
• When the programme has finished the end cycle pilot light
(7.3) comes on.
At the end of the programme
The appliance stops automatically. The pilot
light of the button 6 and the pilot light corresponding to the just finished washing phase go
off. The light 7.3 illuminates.
If a programme or an option that ends with water left in the tub has been selected and the
door remains locked to indicate that the water
must be emptied out before opening the door.
Follow the below instructions to empty out the
water:
18
• Turn the programme selector dial to
.
• Select the draining or spinning programme.
• Reduce the spin speed if needed, by pressing the relevant button.
• Press the button 6.
At the end of the programme, the door can be
now opened. Turn the programme selector dial
to switch the appliance off.
to
Remove the laundry from the drum and carefully
check that the drum is empty. If you do not intend to carry out another wash, close the water
www.zanussi.com
tap. Leave the door open to prevent the formation of mildew and unpleasant smells.
Warning! If there are children or pets in
the house, activate the child safety device in the inner side of the door frame (for
more details read " Child safety" in the chapter
"Safety Information").
a low frequency. By pressing any button the
appliance will come out of the energy saving
status.
Door seal
At the end of every
cycle, check from the
door seal and remove
objects that could be
trapped in the fold.
Stand by: during programme setting up
and once the programme has finished, if
the programme selector dial and any button are
not touched, after a few minutes the energy
saving system is enabled. The pilot lights go off.
The green pilot light of the button 6 flashes with
Washing programmes
Programme - Maximum and Minimum Temperature Cycle Description - Maximum Spin Speed - Maximum
Fabrics Load - Type of Laundry
Options
COTTONS
90°-Cold
Main wash - Rinses - Maximum spin speed at 1400 rpm
Max. load 6 kg - Reduced load 3 kg
White, coloured cotton and linen. Normally soiled items.
AUTOMATIC SPIN REDUCTION
RINSE HOLD
SUPER QUICK1)
EXTRA RINSE
DELAY START
COTTONS + PREWASH
90°- Cold
Prewash - Main wash - Rinses - Maximum spin speed at 1400
rpm
Max. load 6 kg - Reduced load 3 kg
White, coloured cotton and linen. Heavy soiled items.
AUTOMATIC SPIN REDUCTION
RINSE HOLD
SUPER QUICK 1)
EXTRA RINSE
DELAY START
2)
COTTONS ECO
60° - 40°
Main wash - Rinses - Maximum spin speed at 1400 rpm
Max. load 6 kg
White and coloured cotton. This programme can be selected for slightly or normally soiled cotton items. The temperature will decrease and the washing time will be extended. This
allows to obtain a good washing efficiency by saving energy.
AUTOMATIC SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
DELAY START
SYNTHETICS
60° - Cold
Main wash - Rinses - Maximum spin speed at 1200 rpm
Max. load 3 kg - Reduced load 1,5 kg
Synthetic or mixed fabrics: underwear, coloured garments,
non-shrink shirts, blouses . Normally soiled items.
AUTOMATIC SPIN REDUCTION
RINSE HOLD
SUPER QUICK 1)
EXTRA RINSE
DELAY START
www.zanussi.com
Detergent
Compartment
19
Programme - Maximum and Minimum Temperature Cycle Description - Maximum Spin Speed - Maximum
Fabrics Load - Type of Laundry
Options
MIXED FABRICS
Cold
Main wash - Rinses - Maximum spin speed at 1200 rpm
Max. load 3 kg
Highly energy efficient cold wash programme for lightly soiled
laundry. This programme requires a detergent which is active
in cold water.
AUTOMATIC SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
DELAY START
DELICATES
40°- Cold
Main wash - Rinses - Maximum spin speed at 700 rpm
Max. load kg 3 - Reduced load 1,5 kg
Delicate fabrics: acrylics, viscose, polyester . Normally
soiled items.
AUTOMATIC SPIN REDUCTION
RINSE HOLD
SUPER QUICK 1)
EXTRA RINSE
DELAY START
WOOL / HANDWASH
40°- Cold
Main wash - Rinses - Maximum spin speed at 1200 rpm
Max. load 1 kg
Machine washable wool, hand washable woollens and
delicate fabrics with «hand washing» care symbol.
Note: A single or bulky item may cause imbalance. If the appliance doesn’t perform the final spin phase, add more items,
redistribute the load manually and then select the spinning
programme.
AUTOMATIC SPIN REDUCTION
RINSE HOLD
DELAY START
RINSE
Rinse - Short spin speed at 700 rpm.
Max. load 6 kg
To rinse and spin cotton garments which have been washed
by hand. Select the EXTRA RINSE option to intensify the rinsing action. The appliance adds additional rinses.
AUTOMATIC SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
DELAY START,
Detergent
Compartment
DRAIN
Draining of water
For emptying out the water left in the drum in the programmes
with Rinse Hold option.
SPIN
Drain and long spin at maximum spin speed at 1400 rpm
Max. load 6 kg
Separate spin for hand washed garments and after programmes with the Rinse Hold option selected. If the Automatic Spin reduction is selected, by pressing the relevant button,
the appliance performs a short spin.
AUTOMATIC SPIN REDUCTION
DELAY START
EASY IRON
60°- Cold
Main wash - Rinses - Maximum spin speed at 900 rpm
In order to obtain the best anti-creasing result, reduce the
load of synthetics items. (Recommended load 1 Kg)
Synthetic or mixed fabrics. Gentle wash and spin to avoid
any creasing. The appliance performs additional rinses.
AUTOMATIC SPIN REDUCTION
RINSE HOLD
EXTRA RINSE
DELAY START
20
www.zanussi.com
Programme - Maximum and Minimum Temperature Cycle Description - Maximum Spin Speed - Maximum
Fabrics Load - Type of Laundry
Options
5 SHIRTS
30°
Main wash - Rinses - Maximum spin speed at 900 rpm
Synthetics and mixed fabrics. Suitable for 5 - 6 shirts
lightly soiled.
AUTOMATIC SPIN REDUCTION
DELAY START
MINI 30
30°
Main wash - Rinses - Maximum spin speed at 700 rpm
Max. load 2 kg
Synthetics and delicates. Lightly soiled items or which only
needs freshening up.
AUTOMATIC SPIN REDUCTION
DELAY START
JEANS
60°- Cold
Main wash - Rinses - Maximum spin speed at 1200 rpm
Max. load 3 kg
Trousers, shirts or jackets in denim and jersey realized with hitech materials. The Extra Rinse option is activated automatically.
AUTOMATIC SPIN REDUCTION
RINSE HOLD
DELAY START
Detergent
Compartment
1) If you select the SUPER QUICK option by pressing button 4, we recommend that you reduce the maximum
load as indicated. Full loading is possible however with somewhat reduced cleaning results.
2) Standard programmes for the Energy Label consumption values.
According to regulation 1061/2010, these programmes are respectively the «Standard 60 °C cotton
programme» and the «Standard 40 °C cotton programme». They are the most efficient programmes in terms
of combined energy and water consumptions for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the selected
programme.
Consumption values
The data of this table are approximate. Different causes can change the data: the quantity and
type of laundry, the water and ambient temperature.
Programmes
Load
(kg)
Energy consumption
(kWh)
Water consumption (litre)
Approximate
programme
duration (minutes)
Remaining
moisture
(%)1)
Cottons 60 °C
6
1.2
72
170
52
Cottons 40 °C
6
0.75
72
145
52
Synthetics 40 °C
3
0.6
57
95
35
Delicates 40 °C
3
0.6
65
75
35
Wool/Hand wash
30 °C
2
0.3
48
55
30
Standard cotton programmes
www.zanussi.com
21
Programmes
Load
(kg)
Energy consumption
(kWh)
Water consumption (litre)
Approximate
programme
duration (minutes)
Remaining
moisture
(%)1)
Standard 60 °C
cotton
6
1.07
54
194
52
Standard 60 °C
cotton
3
0.79
43
172
52
Standard 40 °C
cotton
3
0.61
43
167
52
1) At the end of spin phase.
Off Mode (W)
Left On Mode (W)
0.65
0.65
The information given in the charts above are in compliance with the EU Commission regulation 1015/2010
implementing directive 2009/125/EC.
Care and cleaning
Warning! Switch the appliance off and remove the mains plug from the socket before
any cleaning action.
Maintenance Wash
With the use of low temperature washes it is
possible to get a build up of residues inside the
drum.
We recommend that a maintenance wash be
performed on a regular basis.
To run a maintenance wash:
• The drum should be empty of laundry.
• Select the hottest cotton wash programme.
• Use a normal measure of detergent, must be
a powder with biological properties.
• Remove the drawer.
• To aid cleaning,
the top part of the
additive compartment should be removed.
Cleaning the dispenser drawer
The washing powder and additive dispenser
drawer should be cleaned regularly.
22
www.zanussi.com
• Use a stiff brush to clean and remove all
washing powder residue.
• Clean all the removed parts of the dispenser drawer under a tap to remove any traces
of accumulated powder.
• before removing
the filter, remove
any fluff or small
objects from
around the filter;
• Use the previous
brush to clean the
recess, ensuring
that upper and
lower part of it is
well cleaned.
After having cleaned the dispenser and the
drawer recess, replace it.
Cleaning the drain filter
The filter permits to hold fluff or foreign bodies
left unawares in the laundry.
The pump must be cleaned regularly.
To clean the filter, proceed as follows:
• turn programme selector dial to position
;
• unplug the appliance;
• open the door;
• remove the filter and clean it under the tap;
• if necessary, place
the filter cover in
the right position
again.
• open the filter cover and insert the filter again;
• turn the drum and
align the filter cover (FILTER) with
the arrow on the
door seal;
• open the filter cover by pressing the
special hook and
by rotating the cover upwards;
Warning! Keep
the filter cover
open until the filter removal.
The filter is inserted correctly when the
indicator on its top is visible and
blocked.
• close the filter cover;
• insert the mains
plug again.
Cleaning the water inlet filters
www.zanussi.com
23
Important! If the appliance doesn't fill, it takes
a long time to fill with water, the starting button
flashes red or the display (if available) shows
the relevant alarm (see chapter "What to do
if..." for more details), check if the water inlet
filters are blocked .
• Screw the hose back onto the tap. Make
sure the connection is tight.
• Unscrew the hose
from the appliance.
Keep a towel nearby because some
water may flow.
• Clean the filter in
the valve with a
stiff brush or with
the piece of cloth.
To clean the water inlet filters:
• Turn off the water
tap.
• Unscrew the hose
from the tap.
• Clean the filter in
the hose with a stiff
brush.
• Screw the hose back to the appliance and
make sure the connection is tight.
• Turn on the water tap.
What to do if…
The appliance does not start or stops during
operation. Certain problems are due to lack of
simple maintenance or oversights, which can
be solved with the help of the indications described in the charts, without calling out an engineer.
Fault code and malfunction
During appliance operation it is possible that
the red pilot light of the button 6 flashes and
one of the indicator pilot lights illuminates to indicate that the appliance is not working.
Before contacting your local Service Centre,
please carry out the checks listed below.
Possible cause - Solution
The light of button 6 flashes and the light 7.1 illuminates: Problem with the water
supply
The water tap is closed.
• Open the water tap.
The inlet hose is squashed or kinked.
• Check the inlet hose connection.
The filter in the inlet hose or the inlet valve filter are blocked
• Clean the water inlet filters (read "Cleaning the water inlet filters"
for more details).
The light of button 6 flashes and the light 7.2 illuminates: Problem with the water
drainage
24
www.zanussi.com
The drain hose is squashed or kinked.
• Check the drain hose connection.
The drain filter is clogged
• If the appliance stops working without discharging the water , first
carry out an emergency drain:
– Turn the programme selector dial to
;
–
–
–
–
–
–
–
–
–
–
–
Unplug the appliance;
Close the water tap;
If necessary, wait until the water has cooled down;
Unscrew the drain hose from the rear support (see "Frost precaution") and unhook it from the sink or spigot;
Let it run along the floor;
Place a bowl on the floor and place the end of the draining hose
into the bowl. The water should drain by gravity into the bowl.
When the bowl is full, empty it. Repeat the procedure until water
stops flowing out ;
Screw the draining hose to the rear support and reposition it;
Open the door and remove the laundry;
Carry out the drain filter cleaning as described in "Cleaning the
drain filter";
At the end of cleaning action, close the door and insert the
mains plug again;
Run a drain programme to check if the appliance works now.
The light of button 6 flashes and the light 7.3 illuminates: Door open
The door has not been closed or is not closed properly.
• Close firmly the door.
The appliance does not start or stops during
operation without any visible alarm.
www.zanussi.com
Before contacting your local Service Centre,
please carry out the checks listed below.
25
Malfunction
Possible cause / Solution
The appliance does not
start:
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The programme selector dial is not correctly positioned and the button 6 has
not been pressed.
• Please turn the selector dial and press the button 6 again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay start.
The appliance fills then
empties immediately:
The end of the drain hose is too low.
• Refer to paragraph in "Water drainage" in chapter "Installation".
The appliance does not
empty and/or does not
spin:
An option or a programme that ends with the water still in the tub or a that
eliminates all the spinning phases has been selected.
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
There is water on the
floor:
Too much detergent or unsuitable detergent (creates too much foam) has
been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fittings. It is not
always easy to see this as the water runs down the hose; check to see if it is
damp.
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Replace it with a new one.
The door will not open:
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the door lock is released.
There is water in the drum.
• Select drain or spin programme to empty out the water.
The appliance vibrates
noisily:
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The appliance is not levelled correctly.
• Adjust the feet.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
26
www.zanussi.com
Malfunction
Possible cause / Solution
Spinning starts late or
the appliance does not
spin:
The electronic unbalance detection device has cut in because the laundry is
not evenly distributed in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen several times before the unbalance disappears and normal spinning can resume. If, after 10 minutes, the laundry is still
not evenly distributed in the drum, the appliance will not spin. In this case, redistribute the load manually and select the spin programme.
• Load more laundry.
The load is too small.
• Add more items, redistribute the load manually and then select the spinning
programme.
No water is visible in
the drum:
Appliances based on modern technology operate very economically using very
little water without affecting performance.
Unsatisfactory washing
results
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
The appliance makes an
unusual noise
The appliance is fitted with a type of motor which makes an unusual noise
compared with other traditional motors. This new motor ensures a softer start
and more even distribution of the laundry in the drum when spinning, as well as
increased stability of the appliance.
Mod
Prod . ...
. No.
...
...
...
...
..
Ser.
No.
...
...
...
After completing these checks, switch on the
appliance and press the button 6 to restart the
programme.
If the malfunction shows again, contact your
Service Centre. The necessary data for the
Mod. ... ... ...
Prod. No. ... ... ...
service centre is on the rating plate. We recommend that you write the data here:
Model description
(MOD.) ........................................
Product number
(PNC) .............................................
Serial number
(S.N.) .................................................
Ser. No. ... ... ...
www.zanussi.com
27
192981731-A-372012
www.zanussi.com/shop