EN
User manual
Washing Machine
ZWG 71202 K
Contents
Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _
Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _
Environment concerns _ _ _ _ _ _ _ _ _ _ _ _
Product description _ _ _ _ _ _ _ _ _ _ _ _ _
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Washing programmes _ _ _ _ _ _ _ _ _ _ _ _
Consumption values _ _ _ _ _ _ _ _ _ _ _ _ _
2
3
4
5
6
7
8
Options _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9
Before first use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10
Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10
Hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 12
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ 13
Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ 15
Technical information _ _ _ _ _ _ _ _ _ _ _ _ 17
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always
keep the instructions with the appliance for future reference.
Children and vulnerable people safety
Warning! Risk of suffocation, injury or permanent disability.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep all detergents away from children.
• Keep children and pets away from the appliance door when it is
open.
• If the appliance has a child safety device, we recommend you activate it.
• Cleaning and user maintenance shall not be made by children
without supervision.
General Safety
• Before maintenance, deactivate the appliance and disconnect
the mains plug from the mains socket.
2
www.zanussi.com
• Do not change the specification of this appliance.
• Obey the maximum load volume of 6 kg (refer to the “Programme
chart” chapter).
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to
avoid a hazard.
• The operating water pressure (minimum and maximum) must be
between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa)
• The ventilation openings in the base (if applicable) must not be
obstructed by a carpet.
• The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.
Safety instructions
Installation
• Remove all the packaging and the transit
bolts.
• Keep the transit bolts. When you move the
appliance again you must block the drum.
• Do not install or use a damaged appliance.
• Do not install or use the appliance where the
temperature is less than 0 °C or where it is
exposed to the weather.
• Obey the installation instruction supplied
with the appliance.
• Make sure that the floor where you install the
appliance is flat, stable, heat resistant and
clean.
• Do not install the appliance where the appliance door can not be fully opened.
• Always be careful when you move the appliance because it is heavy. Always wear safety
gloves.
• Make sure that there is air circulation between the appliance and the floor.
• Adjust the feet to have the necessary space
between the appliance and the carpet.
www.zanussi.com
Electrical connection
Warning! Risk of fire and electrical
shock.
• The appliance must be earthed.
• Make sure that the electrical information on
the rating plate agrees with the power supply. If not, contact an electrician.
• Always use a correctly installed shockproof
socket.
• Do not use multi-plug adapters and extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable. Should
the appliance power supply cable need to
be replaced, this must be carried out by our
Service Centre.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after
the installation.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
• Do not touch the mains cable or the mains
plug with wet hands.
3
• Only for UK and Ireland. The appliance has a
13 amp mains plug. If it is necessary to
change the fuse in the mains plug, use a 13
amp ASTA (BS 1362) fuse.
•
This appliance complies with the E.E.C. Directives.
Water connection
• Make sure not to cause damage to the water
hoses.
• The appliance is to be connected to the water mains using the new supplied hose-sets.
Old hose sets must not be reused.
• Before you connect the appliance to new
pipes or pipes not used for a long time, let
the water flow until it is clean.
• The first time you use the appliance, make
sure that there is no leakage.
Use
Warning! Risk of injury, electrical shock,
fire, burns or damage to the appliance.
• Use this appliance in a household environment.
• Do not change the specification of this appliance.
• Obey the safety instructions on the detergent packaging.
• Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
• Do not touch the glass of the door while a
programme operates. The glass can be hot.
• Make sure that you remove all metal objects
from the laundry.
• Do not put a container to collect possible
water leakage under the appliance. Contact
the Service to ensure which accessories can
be used.
Care and Cleaning
Warning! Risk of injury or damage to the
appliance.
• Before maintenance, deactivate the appliance and disconnect the mains plug from
the mains socket.
• Do not use water spray and steam to clean
the appliance.
• Clean the appliance with a moist soft cloth.
Only use neutral detergents. Do not use
abrasive products, abrasive cleaning pads,
solvents or metal objects.
Disposal
Warning! Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children
and pets to get closed in the appliance.
Environment concerns
Recycle the materials with the symbol . Put
the packaging in applicable containers to
recycle it.
Help protect the environment and human
health and to recycle waste of electrical and
electronic appliances. Do not dispose
appliances marked with the symbol with the
household waste. Return the product to your
local recycling facility or contact your municipal
office.
4
Packaging materials
Recycle the materials with the symbol
.
Put the packaging in applicable containers to
recycle it.
Ecological hints
To help the environment, use less water and
energy, obey these instructions:
• Set a programme without the prewash
phase to wash laundry with normal soil.
• Always start a washing programme with the
maximum load of laundry.
www.zanussi.com
• If necessary, use a stain remover when you
set a programme with a low temperature.
• To use the correct quantity of the detergent,
check the water hardness of your domestic
system
In the interest of the environment
The appliance should be connected to the
FOUL drainage system, the water will then be
taken to a sewage works for treatment before
being discharged safely into a river.
It is essential that these appliances are not
connected to the surface water drainage system as this water is discharged directly into a
river or stream and may cause pollution.
If you require any further advice please contact
your local water authority.
SHOWER
SINK TOILET
BATH
WASHING
MACHINE
RAINWATER
‘RUN-OFF’
DISHWASHER
FOUL DRAIN
SURFACE WATER
DRAINS & SEWERS
FOUL SEWERS
SEWAGE TREATMENT
WORKS
UNTREATED
DISCHARGE
RIVER
BIDET
TREATED DISCHARGE
RIVER
Product description
1
2
1 Worktop
2 Detergent dispenser
3
3 Control panel
4 Door handle
4
5 Rating plate
6 Feet for the appliance level
5
6
Fixing plate kit (405517114)
Available from your authorized dealer.
www.zanussi.com
If you install the appliance on a plinth, secure
the appliance in the fixing plates.
Follow the instructions supplied with the kit.
5
Control panel
1
2
3
4
Delay Start
Specials
Cottons
Cottons
Refresh 20
+Prewash
Jeans
90°
1200
60°
Easy Iron
Cottons Eco
Mix 20°
Synthetics
40°
900
30°
Delicates
Mixed Fabric
Spin
Drain
Rinse
700
Temp.
Rinse Hold
Spin
Super Quick
Extra Rinse
Start /Pause
Wool
Handwash
10
1 Programme knob
2 Display
3 Delay start button (Delay Start)
4 Door locked indicator
5 Start/pause button (Start/Pause)
6 Extra rinse button (Extra Rinse)
7 Super quick button (Super Quick)
8 Rinse hold button (Rinse Hold)
9 Spin reduction button (Spin)
10 Temperature button (Temp.)
9
8
7
6
5
B) The child lock symbol.
The symbol comes on the display when the related function is set.
C) The programme time and the alarm codes.
If the appliance has a malfunction, the display
shows the alarm codes. Refer to the chapter
'Troubleshooting' .
The display shows the message Err for some
seconds if:
– You set a function that is not applicable for
the programme.
– You change the programme while it operates.
Display
The display shows:
A B
6
C
A) The delay start.
When you press the
delay start button, the
display shows the
delay start time.
www.zanussi.com
Washing programmes
Programme
Temperature range
Type of load and soil
Maximum load, Maximum spin
Cotton
90 °C — Cold
White cotton and coloured cotton (normal soil and light soil).
6 kg, 1200 rpm
Cotton +Prewash
90 °C — Cold
White cotton and coloured cotton (heavy soil and normal soil).
6 kg, 1200 rpm
Cottons Eco
60 °C – 40 °C
1)
White cotton and colour-fast cotton. Normal soil.
6 kg, 1200 rpm
Synthetics
60 °C— Cold
Synthetic items or mixed fabric items. Normal soil.
3 kg, 1200 rpm
Delicates
40 °C - Cold
Delicate fabrics as acrylics, viscose, polyester items. Normal soil.
3 kg, 700 rpm
Wool/Handwash
40 °C – Cold
Machine washable wool, hand washable wool and delicate fabrics with «hand washing» care symbol.
2 kg, 1200 rpm
Rinse
To rinse and spin the laundry. All fabrics.
6 kg, 1200 rpm2)
Drain
To drain the water in the drum. All fabrics.
6 kg
Spin
To spin the laundry and to drain the water in the drum. All fabrics.
6 kg, 1200 rpm
Mixed Fabric
40 °C
Special energy saving programme for cotton items with recommended washing temperature 40°C or 60°C.
6 kg, 1200 rpm
Mix 20°
20 °C3)
Very energy efficient programme for cottons, synthetics and
mixed fabrics. Light soil. This programme requires a detergent
which is active in cold water.
3 kg, 1200 rpm
Easy Iron
60 °C - Cold
Synthetic fabric items. Normal soil. It prevents the laundry creases.
1 kg, 900 rpm
Jeans
60 °C - Cold
Items in denim and jersey. Also for items in dark colors. The Extra
Rinse option activates automatically.
3 kg, 1200 rpm
Refresh 20
30 °C
Synthetic and mixed fabric items. Light soil and items to freshen
up.
For 5 - 6 shirts.
900 rpm
1) Standard programmes for the Energy Label consumption values.
According to regulation 1061/2010, these programmes are respectively the «Standard 60 °C cotton
programme» and the «Standard 40 °C cotton programme». They are the most efficient programmes in terms
of combined energy and water consumptions for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the selected
programme.
www.zanussi.com
7
2) The default speed is 700 rpm.
3) The appliance shows the temperature setting as “Cold”.
Programme options compatibility
Spin
Rinse Hold
Super
Quick1)
Extra Rinse
Delay Start
Cotton
∎
∎
∎
∎
∎
Cotton +Prewash
∎
∎
∎
∎
∎
Cottons Eco
∎
∎
∎
∎
Synthetics
∎
∎
∎
∎
∎
∎
∎
∎
∎
Programme
Delicates
Wool /Handwash
∎
∎
Rinse
∎
∎
∎
∎
∎
Drain
Spin
∎
∎
Mixed Fabric
∎
∎
∎
∎
Mix 20°
∎
∎
∎
∎
Easy Iron
∎
∎
∎
∎
Jeans
∎
∎
Refresh 20
∎
∎
∎
1) When you set the Super Quick option, we recommend that you decrease the quantity of the laundry. It is
possible to keep the full load but the washing results can be unsatisfactory. Recommended load: cotton: 3
kg, synthetics and delicates: 1,5 kg.
Consumption values
The data of this table are approximate. Different causes can change the data: the quantity
and type of laundry, the water and ambient temperature.
Programmes
Load
(Kg)
Energy consumption
(kWh)
Water consumption (litre)
Approximate
programme
duration (minutes)
Remaining
moisture
(%)1)
Cottons 60 °C
6
1.05
60
160
53
Cottons 40 °C
6
0.65
60
140
53
Synthetics 40 °C
3
0.47
45
90
35
Delicates 40 °C
3
0.50
60
80
35
Wool/Hand wash
30 °C
2
0.27
47
55
30
Standard cotton programmes
8
www.zanussi.com
Programmes
Load
(Kg)
Energy consumption
(kWh)
Water consumption (litre)
Approximate
programme
duration (minutes)
Remaining
moisture
(%)1)
Standard 60 °C
cotton
6
0.98
47
185
53
Standard 60 °C
cotton
3
0.76
50
173
53
Standard 40 °C
cotton
3
0.59
36
169
53
1) At the end of spin phase.
Off Mode (W)
Left On Mode (W)
0.48
0.48
The information given in the charts above are in compliance with the EU Commission regulation 1015/2010
implementing directive 2009/125/EC.
Options
Temperature button (Temp.)
Press this button to change the default temperature.
— cold water.
Symbol
Spin button (Spin)
With this button you can decrease the spin
speed.
The indicator of the set speed comes on.
Rinse Hold button (Rinse Hold)
Set this function to prevent the laundry creases.
There is a water in the drum when the
programme is completed.
Super quick button (Super Quick)
Press this button to decrease the programme
duration.
Set this function for items with light soil or
items to refresh.
Extra rinse button (Extra Rinse)
Press this button to add rinsing phases to a
programme.
Use this function for persons allergic to detergents and in areas where the water is soft.
www.zanussi.com
Delay start button (Delay Start)
Press this button to delay the start of a programme from 30 minutes to 20 hours.
Permanent extra rinse function
With this option you can permanently have an
extra rinse when you set a new programme.
• To activate this function press the button
“Rinse Hold” and the button “Extra Rinse” at
the same time. The indicator of the button
“Extra Rinse” comes on.
• To deactivate this function press the same
buttons again until the indicator of the button
“Extra Rinse” goes off.
Child lock function
This function prevents the children to play with
the control panel.
• To activate the function, press the button
“Temp.” and the button “Spin” at the same
.
time until the display shows the symbol
• To deactivate the function, press the same
goes off.
buttons until the symbol
You can activate the function:
• Before you press the Start/Pause button:
the appliance cannot start.
9
• After you press the Start/Pause button, all
the buttons and the programme knob do not
operate.
Before first use
Put a small quantity of detergent in the main
wash compartment of the detergent dispenser.
Set and start a programme for cotton at the
highest temperature without laundry. This removes all possible dirt from the drum and the
tub.
Daily use
1.
2.
3.
4.
5.
Open the water tap.
Connect the mains plug to the mains
socket.
Put the laundry in the appliance.
Use the correct quantity of detergent and
additives.
Set and start the correct programme for
the type of laundry and soil.
Loading the laundry
1.
2.
3.
Liquid additives compartment (fabric
conditioner, starch).
Put the product in the compartment
before you start the programme.
Flap for powder or liquid detergent.
Open the appliance door.
Put the laundry in the drum, one item at a
time. Shake the items before you put
them in the appliance. Make sure not to
put too much laundry in the drum.
Close the door.
Caution! Make
sure that no
laundry stays between the seal and
the door. There is a
risk of water leakage
or damage to the
laundry.
Using the detergent and additives
10
The detergent compartment for the
washing phase.
If you use a liquid detergent, put it immediately before you start the programme.
When you set a programme with a prewash,
put the detergent for prewash phase directly into
the drum.
Using the liquid and the powder
detergent
A
The default position
of the flap is A (powder detergent).
To use liquid detergent:
1. Remove the
drawer. Push the
drawer edge in
the place with
the arrow
(PUSH) to remove the drawer
easily.
www.zanussi.com
B
2.
3.
Adjust the flap in
position B.
Put back the
drawer in the recess.
• The indicator of button Start stops to flash.
The indicator of the locked door is on.
• The programme starts and the door locks.
• The programme time decreases with steps
of one minute.
The appliance does a short spin at the
start of some washing programmes.
–
–
–
–
When you use the liquid detergent:
Do not use gelatinous or thick liquid detergents.
Do not put more liquid then 120 ml.
Do not set the prewash phase.
Do not set the delay start.
A
When the flap is in
position B and you
want to use powder
detergent:
1. Remove the
drawer.
2. Adjust the flap in
position A.
3. Put back the
drawer in the recess.
• Measure out the detergent and the fabric
conditioner.
• Put the detergent and the fabric conditioner into the compartments.
• Carefully close the detergent drawer.
Setting a programme
1. Turn the programme knob and set the programme:
– The indicator of Start button flashes.
– The display shows the programme duration.
2. If necessary, change the temperature and
the spin speed or add available functions.
When you press the relevant button, the
indicator of the set function comes on.
Starting a programme without the delay
start
Press the Start button:
www.zanussi.com
Starting a programme with the delay start
• Press the “Delay Start” button again and
again until the display shows the delay you
want to set. The related symbol comes on.
• Press the Start/Pause button:
The appliance starts the countdown.
When the countdown is completed, the programme starts automatically.
You can change or cancel the delay start
before you press the Start button. After
pressing the Start button you can only cancel
the delay.
To cancel the delay start:
1. Press the Start/Pause button to set the
appliance to PAUSE.
2. Press the “Delay Start” button. The display
shows ’.
3. Press the Start/Pause button again to start
the programme immediately.
Interruption of a programme
1. Press the button Start/Pause. The indicator flashes.
2. Press the button Start/Pause again. The
washing programme continues.
Cancel a programme
1. Turn the programme knob to
to cancel
the programme and to deactivate the appliance.
2. Turn the programme knob again to activate
the appliance. Now, you can set a new
washing programme.
The appliance does not drain the water.
Changing the options
You can change only some options before they
operate.
11
1.
2.
3.
Press the button Start/Pause. The indicator flashes.
Change the options.
Press the button Start/Pause again. The
programme continues.
Open the door
While a programme or the delay start operates,
the appliance door is locked. The indicator
is on.
Caution! If the temperature and level of
the water in the drum are too high, you
cannot open the door.
To open the appliance door when the
delay start operates:
1. Press the button Start/Pause to set the
appliance to PAUSE.
2. Wait until the indicator
goes off.
3.
4.
You can open the door.
Close the door and press the button Start/
Pause again. The delay start continues to
operate.
To open the appliance door when the
programme operates:
1. Turn the programme knob to
to deactivate the appliance.
2. Wait for some minutes and then open the
appliance door.
3. Close the appliance door.
4. Set the programme again.
At the end of the programme
• The appliance stops automatically.
• The acoustic signals operate.
• In the display
comes on.
• The door lock indicator
1.
2.
3.
4.
goes off.
.
Turn the programme knob to
Remove the laundry from the appliance.
Make sure that the drum is empty.
Keep the door ajar, to prevent the mildew
and odours.
Close the water tap.
The washing programme is completed,
but there is water in the drum:
– The drum turns regularly to prevent the creases in the laundry.
– The door lock indicator
is on. The door
stays locked.
– You must drain the water to open the door.
To drain the water:
1. Set the Drain or the Spin programme.
2. Press theStart/Pause button . The appliance drains the water and spins.
3. When the programme is completed and
the door lock indicator goes off, you can
open the door
4. Turn the programme knob to
to deactivate the appliance.
Stand by
Some minutes after the end of the washing
programme, if you do not deactivate the appliance, the energy saving status activates.
The energy saving status decreases the energy
consumption when the appliance is on the
standby.
• All indicators and the display go off.
• The indicator of button Start flashes slowly
Press one of the buttons to deactivate the energy saving status.
• The indicator of the Start/Pause button goes
off.
Hints and tips
The laundry load
• Divide the laundry in: white, coloured, synthetics, delicates and wool.
• Obey the washing instructions that are on
the laundry care labels.
12
• Do not wash together white and coloured
items.
• Some coloured items can discolour with the
first wash. We recommend that you wash
them separately for the first times.
www.zanussi.com
• Button up pillowcases, close zippers, hooks
and poppers. Tie up belts.
• Empty the pockets and unfold the items.
• Turn inside out multilayered fabrics, wool
and items with painted illustrations.
• Remove hard stains.
• Wash with a special detergent heavy soil
stains.
• Be careful with the curtains. Remove the
hooks or put the curtains in a washing bag
or pillowcase.
• Do not wash in the appliance :
– Laundry without hems or with cuts
– Underwired bras.
– Use a washing bag to wash small items.
• A very small load can cause balance problems with the spin phase. If this occurs, adjust manually the items in the tub and start
the spin phase again.
Stubborn stains
For some stains, water and detergent is not
sufficient.
We recommend that you remove these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the
type of stain and fabric.
Detergents and additives
• Only use detergents and additives specially
made for washing machines.
• Do not mix different types of detergents.
• To help the environment, do not use more
than the correct quantity of detergent.
• Obey the instructions that you find on the on
packaging of these products.
• Use the correct products for the type and
colour of the fabric, the programme temperature and the level of soil.
• If you use liquid detergents, do not set the
prewash phase.
• If your appliance has not the detergent dispenser with the flap device, add the liquid
detergents with a dosing ball.
Water hardness
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where
the water hardness is soft it is not necessary to
use a water softener.
To know the water hardness in your area, contact your local water authority.
Obey the instructions that you find on the
packaging of the products.
Care and cleaning
External cleaning
Clean the appliance only with soap and warm
water. Fully dry all the surfaces.
Caution! Do not use alcohol, solvents or
chemical products.
Descaling
The water we use contains limescale. If it becomes necessary, use a water softener to remove limescales.
Use a special product made for washing machines. Obey the instructions that you find on
the packaging of the manufacturer.
Do this separately from the laundry wash.
www.zanussi.com
Maintenance wash
With the low temperature programmes it is
possible that some detergent stays in the
drum. Make regularly a maintenance wash. To
do this:
• Empty the laundry from the drum.
• Set the hottest cotton wash programme
• Use a correct quantity of powder detergent
with biological properties.
After each wash, keep the door open for a
while to prevent mould and to let unpleasant
smells go out.
Drum
Regularly examine the drum to prevent limescale and rust particles.
13
Only use special products to remove rust particles from the drum.
To do this:
• Clean the drum with special product for
stainless steel.
• Start a short programme for cotton at the
maximum temperature with a small quantity
of detergent.
5.
6.
Door seal
Regularly examine
the seal and remove
all objects from the
inner part.
The inlet hose filter and the valve filter
To clean the water inlet filters:
1.
2.
1
2
Detergent dispenser
3
To clean the dispenser:
1.
2.
3.
4.
20°
3.
45°
4.
Frost precautions
If the appliance is installed in an area where
the temperature can be less than 0 °C, remove
the remaining water from the inlet hose and the
drain pump.
1.
2.
3.
4.
14
Disconnect the mains plug from the
mains socket.
Close the water tap.
Remove the water inlet hose
Remove the drain hose from the rear
support and unhook it from sink or spigot
www.zanussi.com
5.
6.
Put the ends of the drain and inlet hose
in a container. Let the water flow out of
the hoses.
When no more water flows, install the inlet hose and the drain hose again.
Warning! Make sure that the temperature
is more than 0 °C before you use the
appliance again.
The manufacturer is not responsible for
damages caused by low temperatures.
Troubleshooting
The start of the appliance does not occur or it
stops during operation.
First try to find a solution to the problem (refer
to the table). If not, contact the service centre.
With some problems, the acoustic
signals operate and the display shows an
alarm code:
•
- The appliance does not fill with water.
Problem
The appliance does not
start.
•
- The appliance does not drain the
water.
•
- The appliance door is open or not
closed correctly.
Warning! Deactivate the appliance
before you do the checks.
Possible solution
Make sure that the mains plug is connected in the mains socket.
Make sure that the appliance door is closed.
Make sure that there is not a damaged fuse in the household fuse box.
Make sure that the button Start/Pause has been pressed.
If the delay start is set, cancel the setting or wait for the end of the countdown.
Make sure that the programme knob is in the correct position.
Deactivate the Child Lock function if it is on.
The appliance does not
fill with water.
Make sure that the water tap is opened.
Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the filter of the inlet hose and the filter of the valve are not clogged. Refer to 'Care and cleaning'.
Make sure that the inlet hose has no kinks or bends.
Make sure that the connection of the water inlet hose is correct.
The appliance does not
drain the water.
Make sure that the sink spigot is not clogged.
Make sure that the water drain hose has no kinks or bends.
www.zanussi.com
15
Problem
Possible solution
Make sure that the connection of the water drain hose is correct.
Set the drain programme if you set a programme without the drain phase.
Set the drain programme if you set an option which ends with water in the drum.
If above mentioned solutions do not help, contact the Service (as the filter of the
drain pump may be clogged).
The spin phase does
not operate
or
the washing cycle lasts
longer than usually.
Adjust manually the items in the drum and start the spin phase again. This problem may be caused by balance problems.
Set the spin programme.
Set the drain programme if you set an option which ends with water in the drum.
If above mentioned solutions do not help, contact the Service (as the filter of the
drain pump may be clogged).
There is water on the
floor.
Make sure that the couplings of the water hoses are tight and there are no water
leakages.
Make sure that the water inlet hose and the water drain hose has no damages.
Make sure you use the correct detergent and the correct quantity of it.
You cannot open the
appliance door.
Make sure that the washing programme is finished.
Set the drain or the spin programme if there is water in the drum.
The appliance makes
an unusual noise.
Make sure that the leveling of the appliance is correct. Refer to 'Installation instruction'.
Make sure that the packaging and/or the transit bolts are removed. Refer to 'Installation instruction'.
Add more laundry in the drum. The load may be too small.
The appliance fills with
water and drain immediately.
Make sure that the drain hose is in the correct position. The end of the hose may
be is too low. Refer to 'Installation instruction'.
The washing results are
not satisfactory.
Increase the detergent quantity or use a different detergent.
Use special products to remove the stubborn stains before you wash the laundry.
Make sure that you set the correct temperature.
Decrease the laundry load.
After the check, activate the appliance. The
programme continues from the point of interruption.
If the problem occurs again, contact the Service.
If the display shows other alarm codes, activate
and deactivate the appliance. If the problem
continues, contact the Service.
16
Service
We recommend the use of original spare parts.
When contacting the Service, make sure that
these data are available. You can find the information on the rating plate: model (Mod.), PNC
(Prod.No.), Serial number (Ser.No.).
www.zanussi.com
Technical information
Dimensions
Width / Height / Depth
Total depth
Electrical connection:
Voltage
Overall power
Fuse
Frequency
Level of protection against ingress of solid particles and moisture ensured by the protective cover, except where the low voltage equipment
has no protection against moisture
Water supply pressure
600 / 850 / 502 mm
519 mm
230-240 V
2100 W
13 A
50 Hz
IPX4
Minimum
0,5 bar (0,05 MPa)
Maximum
8 bar (0,8 MPa)
Water supply 1)
Cold water
Maximum load
Cotton
Spin speed
Maximum
6 kg
1200 rpm
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
www.zanussi.com
17
18
www.zanussi.com
www.zanussi.com
19
192981622-A-242013
www.zanussi.com/shop