User Guide

PCT Multi Touch Monitor Display

OF17T100-A1-PCT

American Industrial Systems - OF17T100-A1-PCT User Guide Page 1

The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright © 2013 American

Industrial Systems. All rights are reserved. No part of this document may be reproduced, translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission. Windows is a registered trademark of Microsoft, Inc. Other brand or product names are trademarks of their respective holders.

American Industrial Systems, Inc.

http://www.aispro.com

The test results show that this device meets the FCC rules. Those limits are set to protect residential areas from the devices with harmful emission. This device will produce, use and radiate radio frequency energy. In addition, failure to follow the user’s manual to install or use this device might produce harmful interference with radio communication. Notwithstanding the foregoing, it does not guarantee that this type of harmful interference does not occur in some special installations. The interference caused by this device to the reception of radio or television signals may be verified by turning it on and off. Any changes or modifications to this TFT LCD would void the user’s authority to operate this device.

Important Recycle Instruction:

Lamp(s) inside this product contains mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the

Electronic Industries Alliance at WWW.EIAE.ORG

. For lamp specific disposal information check WWW.LAMPRECYCLE.ORG

American Industrial Systems - OF17T100-A1-PCT User Guide Page 2

Table of Contents

Introduction ..................................................................................................................................................5

About OF17T100-A1-PCT ..........................................................................................................................5

Touch Screen for OF17T100-A1-PCT...............................................................................................................6

Package Overview.....................................................................................................................................7

Installation ....................................................................................................................................................8

Product Overview .....................................................................................................................................8

Front View.............................................................................................................................................8

Bottom View .........................................................................................................................................8

Attaching the Side Brackets ......................................................................................................................9

Side mount for Your Monitor..................................................................................................................10

Cut-Out Dimensions................................................................................................................................11

Connecting the Display ...........................................................................................................................12

User Controls ..............................................................................................................................................13

Back Panel Controls ................................................................................................................................13

How to Use the OSD Menus ...................................................................................................................14

On-Screen Display Menus.......................................................................................................................15

Appendix .....................................................................................................................................................16

Troubleshooting ......................................................................................................................................16

Warning Signal ........................................................................................................................................17

Product Dimension .................................................................................................................................18

Compatibility Modes...............................................................................................................................19

Touch Screen Driver Installation.............................................................................................................20

American Industrial Systems - OF17T100-A1-PCT User Guide Page 3

Usage Notice

!

Warning!

To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture.

Do not open or disassemble the product as this may cause electrical shock.

Precautions

Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit.

Do:

• Turn off the product before cleaning.

• Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass commercial cleaners or 50/50 mixture of water and isopropyl alcohol.

• Use a soft cloth moistened with mild detergent to clean the display housing.

• Disconnect the power plug from AC outlet if the product is not going to be used for an extended period of time.

Don’t:

• Do not touch the LCD Display screen surface with sharp or hard objects.

• Do not use abrasive cleaners, waxes or solvents for your cleaning.

• Do not operate the product under the following conditions:

Extremely hot, cold or humid environment.

Areas susceptible to excessive dust and dirt.

Near any appliance generating a strong magnetic field.

In direct sunlight.

American Industrial Systems - OF17T100-A1-PCT User Guide Page 4

Introduction

About OF17T100-A1-PCT

OF = Open frame

R = Regular width ratio of 4:3

17 = Diagonal viewing area in inches

PCT = Projected Capacitive Touch

The monitor has a flat panel screen with an active matrix, thin-film transistor (TFT) liquid crystal display (LCD).

Features include:

• Direct Analog signal input

• Active matrix TFT LCD technology

• 1280 x 1024 XGA resolution

• 17" viewable display area

• 31.47 ~ 80 KHz horizontal scan

• 56 ~ 75 Hz high refresh rate

• 0.264mm x 0.264mm pixel pitch

• Auto adjustment function

• Multilingual OSD user control

• Bracket mount

• 75/100 mm VESA mount

• Removable base for flexible mounting solutions.

• Projected Capacitive touch screen with USB controller.

American Industrial Systems - OF17T100-A1-PCT User Guide Page 5

Touch Screen for OF17T100-A1-PCT

• Projected capacitive touch screen for finger input only

• Surface: Glare treatment

• Interface: USB controller

• Transmittance: 90±5%

• HID: Windows® 7

• Driver: VISTA, XP, 2000, CE, XP Embedded, Linux, Apple® Mac OS

American Industrial Systems - OF17T100-A1-PCT User Guide Page 6

Package Overview

American Industrial Systems - OF17T100-A1-PCT User Guide Page 7

Installation

Product Overview

Front View

Bottom View

American Industrial Systems - OF17T100-A1-PCT User Guide Page 8

Attaching the Side Brackets

Depending on your mounting scheme, alternately, you may use the side brackets to mount your displays onto your wall or device.

Find a suitable location for attaching side brackets.

A. The left and right sides

B. The Top and bottom sides

Note:

You will need a screwdriver to attach the side brackets.

Your kiosk touch monitor included 4 side brackets (R/C/W x2, P-Cap x4) and 8 screws, M4x6

(R/C/W x4, P-Cap x8).

This equipment is intended to be mounted in accordance with the proper hardware and the installation instructions supplied with the product. Use of mounting brackets or screws other than those specified in the installation instructions may cause a hazard.

American Industrial Systems - OF17T100-A1-PCT User Guide Page 9

Side mount for Your Monitor

This monitor can be mounted to the wooden or concrete wall with 4 screws and a pair brackets on the opposites.

American Industrial Systems - OF17T100-A1-PCT User Guide Page 10

Cut-Out Dimensions

American Industrial Systems - OF17T100-A1-PCT User Guide Page 11

Connecting the Display

To setup this display, please refer to the following figure and procedures.

1. Be sure all equipment is turned off.

2. Connect the DC adapter to the power connector on the monitor and the other end into an electrical outlet.

3. Connect the D-SUB cable from the display’s VGA input connector to the D-SUB connector of your host computer and tighten the screws.

4. Connect the RS-232 or USB cable from the RS-232 or USB port of your display to the RS-232 port or USB port of your computer.

5. Configure the touch screen. Refer to the “Touch Screen Driver Installation” section on page 19.

6. Once the touch screen is configured, the monitor is ready for use.

7. Connect the remote control cable to RJ-Type port

!

Notice!

To ensure the LCD display works well with your computer, please configure the display mode of your graphics card to make it less than or equal to 1280 x 1024 resolution and make sure the timing of the display mode is compatible with the LCD display.

We have listed the compatible “Video Modes” of your LCD display in the appendix (on page 19) for your reference.

Don't connect telephone or internet cable to RJ-Type port.

Adapter rating: 12Vdc 3A min., marked with LPS.

American Industrial Systems - OF17T100-A1-PCT User Guide Page 12

User Controls

Back Panel Controls

American Industrial Systems - OF17T100-A1-PCT User Guide Page 13

How to Use the OSD Menus

1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the five functions in the main menus.

2. Choose the adjustment items by pressing the “Enter ” button.

3. Adjust the value of the adjustment items by pressing the “Up” or “Down” button.

4. With the OSD menu on screen, press “ Menu” button to return main menu or exit

OSD.

5. The OSD menu will automatically close, if you have left it idle for a pre-set time.

6. To Lock the OSD / Power menu buttons, please follow the instructions below.

(Please note: the monitor has to be turned ON with a valid signal pre-set) a. Press “Menu” key , the OSD menu will pops upon display.

b. Press and hold the “Menu” key again with the OSD menu on the screen, the

OSD menu will disappear. Then press the “Power” key 1 time while the menu key is still being pressed. The “Lock/Unlock” menu will appear for 3 seconds.

c. Use the “Enter” key to select OSD or Power setting then set at “Lock” by pushing the “UP” or “Down” button.

d. When the “UP” or “Down” button is released, the previous setting will be saved and exit the “Lock/Unlock” menu automatically.

8. To Unlock the OSD / Power menu buttons, please follow the instructions below.

(Please note: the monitor has to be turned ON with a valid signal pre-set) a. Press and hold the “Menu” key then press the “Power” key simultaneously, the “Lock/ Unlock” menu will appear for 3 seconds.

b. Use the “Enter” key to select OSD or Power setting then set at “Unlock” by pushing the “UP” or “Down” button.

c. When the “UP” or “Down” button is released, the previous setting will be saved and exit the “Lock/Unlock” menu automatically.

Please note: a. When the OSD Lock function is selected, this indicates that all the buttons except “power” button are now disabled.

b.

When the Power Lock function is selected, this indicates that the power key is disabled; user can not to turn off the monitor by “Power” key.

American Industrial Systems - OF17T100-A1-PCT User Guide Page 14

On-Screen Display Menus

Main OSD Menu:

American Industrial Systems - OF17T100-A1-PCT User Guide Page 15

Appendix

Troubleshooting

If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or our service center.

Problem: No image appears on screen



Check that all the I/O and power connectors are correctly and well-connected as described in the “Installation” section.



Make sure the pins of the connectors are not crooked or broken.

Problem: Partial Image or incorrectly displayed image



Check to see if the resolution of your computer is higher than that of the LCD display.



Reconfigure the resolution of your computer to make it less than or equal to 1280 x 1024.

Problem: Image has vertical flickering line bars



Use “Fine” to make an adjustment.



Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the LCD display.

Problem: Image is unstable and flickering



Use “Fine” to make an adjustment.

Problem: Image is scrolling



Check and make sure the VGA signal cable (or adapter) is securely connected.



Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the LCD display.

Problem: Vague image (characters and graphics)



Use “Fine” to make an adjustment. If this problem persists, use “Horizontal size” to make an adjustment.

American Industrial Systems - OF17T100-A1-PCT User Guide Page 16

Warning Signal

If you see warning messages on your LCD screen, this means that the LCD display cannot receive a clean signal from the computer graphics card.

Below are the three kinds of Warning Signal. Please check the cable connections or contact your local dealer or our service center for more information.

No Signal

This message means that the LCD display has been powered on but it cannot receive any signal from the computer graphics card. Check all the power switches, power cables, and VGA/DVI signal cable.

Going to Sleep

The LCD display is under the power saving mode. In addition, the LCD display will enter power saving mode when experiencing a sudden signal disconnecting problem.

The monitor can be activated by pressing any keyboard, triggering the mouse or touching the screen.

Out of Range

This message means that the signal of the computer graphic card is not compatible with the LCD display. When the signal is not included in the “Video Modes” list we have listed in the Appendices of this manual, the LCD monitor will display this message.

American Industrial Systems - OF17T100-A1-PCT User Guide Page 17

Product Dimension

American Industrial Systems - OF17T100-A1-PCT User Guide Page 18

Compatibility Modes

American Industrial Systems - OF17T100-A1-PCT User Guide Page 19

Touch Screen Driver Installation

The monitor is available with USB connection. The Linux kernel 2.6.x (32 bit & 64 bit) touch driver is located on the enclosed CD-ROM. HID for Windows® 7, VISTA , XP,

2000, ME, 98.

Please Note:

The system requires 15 seconds for Windows® 7 to install/uninstall the touch drivers while turning power on/off or plugging/unplugging USB cable.

Driver Install Instructions:

If you are using a PC running driver Linux kernel 2.6.x (32 bit & 64 bit), follow the instructions below:

1. Power on the PC.

2. Be sure the USB cable is connected from the PC to the LCD display.

3. Open the CD-ROM.

4. Follow the step-by-step instructions as shown on the pop-up windows.

If you are using a PC running Windows® XP Embedded, follow the instructions below:

Express:

1. Power on the computer.

2. Make sure that the USB cable is connected to the computer.

3. Be sure that your EWF is disabled. If your EWF is enabled, please disable the EWF by using the EWF Manager command.

4. Once the EWF is disabled click on the XP driver on the CD-ROM and follow the step-by-step instructions as shown on the pop-up windows.

Custom:

1. Power on the computer.

2. Make sure that the USB cable is connected to the computer.

3. Follow the step-by-step instructions found in the folder fi le on the CD-ROM.

If you are using a PC running Windows® CE, follow the instructions below:

1. Power on the computer.

2. Make sure that the USB cable is connected to the computer.

3. Using Platform Builder, build an image fi le by following the step-by-step instructions found in the folder fi le on the CD-ROM.

American Industrial Systems - OF17T100-A1-PCT User Guide Page 20

If you are using a PC running Linux or Apple® Mac OS, follow the instructions below:

1. Power on the computer.

2. Make sure that the USB cable is connected to the computer.

3. Follow the step-by-step instructions found in the folder file on the CD-ROM.

American Industrial Systems - OF17T100-A1-PCT User Guide Page 21