Philips Signage Solutions E-Line Display BDL4652EL

BDL4652EL
www.philips.com/welcome
User Manual (English)
BDL4652EL
Safety Instructions
Safety precautions and maintenance
WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to
shock, electrical hazards and/or mechanical hazards.
Read and follow these instructions when connecting and using your display:
Operation:
• Keep the display out of direct sunlight and away from stoves or any other heat sources.
• Remove any object that could fall into ventilation holes or prevent proper cooling of the display’s electronics.
• Do not block the ventilation holes on the cabinet.
• When positioning the display, make sure the power plug and outlet are easily accessible.
• When turning off the display by detaching the power cord, wait 6 seconds before re-attaching the power cord for normal operation.
• Ensure the use of an approved power cord provided by Philips at all times. If your power cord is missing, please contact your local service center.
• Do not subject the display to severe vibration or high impact conditions during operation.
• Do not knock or drop the display during operation or transportation.
Maintenance:
• To protect your display from possible damage, do not put excessive pressure on the LCD panel. When moving your display, grasp the frame to lift; do
not lift the display by placing your hand or fingers on the LCD panel.
• Unplug the display if you are not going to use it for an extensive period of time.
• Unplug the display if you need to clean it with a slightly damp cloth. The screen may be wiped with a dry cloth when the power is off. However, never
use organic solvent, such as, alcohol, or ammonia-based liquids to clean your display.
• To avoid the risk of shock or permanent damage to the set, do not expose the display to dust, rain, water or an excessively moist environment.
• If your display becomes wet, wipe it with dry cloth as soon as possible.
• If a foreign substance or water gets in your display, turn the power off immediately and disconnect the power cord. Then remove the foreign substance
or water, and send the unit to the maintenance center.
• Do not store or use the display in locations exposed to heat, direct sunlight or extreme cold.
• In order to maintain the best performance of your display and ensure a longer lifetime, we strongly recommend using the display in a location that falls
within the following temperature and humidity ranges.
-- Temperature: 0-40°C 32-104°F
-- Humidity: 20-80% RH
IMPORTANT: Always activate a moving screen saver program when you leave your display unattended. Always activate a periodic screen refresh
application if the unit will display unchanging static content. Uninterrupted display of still or static images over an extended period may cause “burn in”,
also known as “after-imaging” or “ghost imaging”, on your screen. This is a well-known phenomenon in LCD panel technology. In most cases, the “burned
in” or “after-imaging” or “ghost imaging” will disappear gradually over a period of time after the power has been switched off.
WARNING: Severe “burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired. This is also not covered under the
terms of your warranty.
Service:
• The casing cover should be opened only by qualified service personnel.
• If there is any need for repair or integration, please contact your local service center.
• Do not leave your display under direct sunlight.
If your display does not operate normally, having followed the instructions set out in this document, please contact a technician or your
local service center..
ii
BDL4652EL
Read and follow these instructions when connecting and using your display:
• Unplug the display if you are not going to use it for an extensive period of time.
• Unplug the display if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth when the power is
off. However, never use alcohol, solvents or ammonia-based liquids.
• Consult a service technician if the display does not operate normally when you have followed the instructions in this manual.
• The casing cover should be opened only by qualified service personnel.
• Keep the display out of direct sunlight and away from stoves or any other heat sources.
• Remove any object that could fall into the vents or prevent proper cooling of the display’s electronics.
• Do not block the ventilation holes on the cabinet.
• Keep the display dry. To avoid electric shock, do not expose it to rain or excessive moisture.
• When turning off the display by detaching the power cable or DC power cord, wait for 6 seconds before re-attaching the power
cable or DC power cord for normal operation..
• To avoid the risk of shock or permanent damage to the set do not expose the display to rain or excessive moisture.
• When positioning the display, make sure the power plug and outlet are easily accessible.
• IMPORTANT: Always activate a screen saver program during your application. If a still image in high contrast remains on the
screen for an extended period of time, it may leave an ‘after-image’ or ‘ghost image’ on the front of the screen. This is a well-known
phenomenon that is caused by the shortcomings inherent in LCD technology. In most cases the afterimage will disappear gradually
over a period of time after the power has been switched off. Be aware that the after-image symptom cannot be repaired and is not
covered under warranty.
iii
BDL4652EL
Regulatory Information
CE Declaration of Conformity
We declare under our responsibility that the product is in conformity with the following standards:
• EN60950-1:2006+A11:2009+A1:2010+A12:2011 (Safety requirement of Information Technology Equipment).
• EN55022:2010 (Radio Disturbance requirement of Information Technology Equipment).
• EN55024:2010 (Immunity requirement of Information Technology Equipment).
• EN61000-3-2:2006 +A1:2009+A2:2009 (Limits for Harmonic Current Emission).
• EN61000-3-3:2008 (Limitation of Voltage Fluctuation and Flicker)
• EN 50581:2012 (Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous
substances)
following provisions of directives applicable.
• 2006/95/EC (Low Voltage Directive).
• 2004/108/EC (EMC Directive).
• 2009/125/EC (ErP, Energy-related Product Directive, EC No. 1275/2008 and 642/2009 Implementing)
• 2011/65/EU (RoHS Directive) and is produced by a manufacturing organization on ISO9000 level.
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Use only an RF shielded cable that was supplied with the display when connecting this display to a computer device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE- CAUSING EQUIPMENT REGULATIONS.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
iv
BDL4652EL
Polish Center for Testing and Certification Notice
The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer,
display, printer, and so on) should have the same power supply source.
The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value
no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the
equipment and easily accessible.
A protection mark “B” confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/
E-06251.
Electric, Magnetic and Electronmagnetic Fields (“EMF”)
1. We manufacture and sell many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive
electromagnetic signals.
2. One of our leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal
requirements and to stay well within the EMF standards applicable at the time of producing the products.
3. We are committed to develop, produce and market products that cause no adverse health effects.
4. We confirm that if its products are handled properly for their intended use, they are safe to use according to scientific evidence available today.
5. We play an active role in the development of international EMF and safety standards, enabling us to anticipate further developments in standardization
for early integration in its products.
v
BDL4652EL
Information for U.K. only
WARNING - THIS APPLIANCE MUST BE EARTHED.
(B)
Important:
(A)
This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug
proceed as follows:
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin
plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse
at the distribution board should not be greater than 5A.
NOTE:
he severed plug must be destroyed to avoid a possible shock hazard should it be inserted
T
into a 13A socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured in accordance with the following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN & YELLOW - “EARTH” (“E”)
1. The GREEN & YELLOW wire must be connected to the terminal in the plug which is marked with
the letter “E” or by the Earth symbol or coloured GREEN or GREEN & YELLOW.
2. The BLUE wire must be connected to the terminal which is marked with the letter “N” or coloured
BLACK.
3. The BROWN wire must be connected to the terminal which marked with the letter “L” or
coloured RED.
Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead
- not simply over the three wires.
vi
BDL4652EL
China RoHS
中国电子信息产品污染控制标识要求 (中国RoHS法规标示要求) 产品中有毒有害物质或元素
的名称及含量
有毒有害物质或元素
部件名称
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr 6+)
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
外壳
O
O
O
O
O
O
液晶面板
X
O
O
O
O
O
电路板组件
X
O
O
O
O
O
附件
(遥控器,电源线,连接线)
X
O
O
O
O
O
遥控器电池
X
O
O
O
O
O
O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下.
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求.
10
環保使用期限
此標識指期限(十年),電子信息產品中含有的有毒有害物質或元素在正常使用的條件下不會發生外泄或突變
,電子信息產品用戶使用該電子信息產品不會對環境造成嚴重污染或對其人身、財產造成嚴重損害的期限。
vii
BDL4652EL
North Europe (Nordic Countries) Information
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS.
Placering/Ventilation
ADVARSEL:
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
End-of-Life Disposal
Your new Public Information Display contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the
amount of reusable materials and to minimize the amount to be disposed of.
Please find out about the local regulations on how to dispose of your old display from your local Philips dealer.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information on recycling
contact www.eia.org (Consumer Education Initiative)
Waste Electrical and Electronie Equipment-WEEE
Attention users in European Union private households
This marking on the product or on its packaging illustrates that, under European Directive 2012/19/EU governing used electrical and
electronic appliances, this product may not be disposed of with normal household waste. You are responsible for disposal of this
equipment through a designated waste electrical and electronic equipment collection. To determine the locations for dropping off such
waste electrical and electronic, contact your local government office, the waste disposal organization that serves your household or the
store at which you purchased the product.
Attention users in United States:
Please dispose of according to all Local, State and Federal Laws. For the disposal or recycling information, contact: www.mygreenelectronics.com or www.
eiae.org.
End of Life Directives-Recycling
Your new Public Information Display contains several materials that can be recycled for new users.
Please dispose of according to all Local, State, and Federal laws.
viii
BDL4652EL
Table Of Contents
1. Unpacking and Installation...................................... 1
1.1. Unpacking......................................................................1
1.2. Package Contents......................................................1
1.3. Installation Notes.......................................................1
1.4. Installing and Removing Table Stands
(optional)........................................................................2
1.5. Mounting on a Wall..................................................3
1.5.1. VESA Grid.....................................................3
1.6. Mounting in Portrait Position..............................4
1.6.1. How to use the logo guider for
portrait position.........................................4
1.6.2. How to remove the logo......................4
1.7. Operating Instructions of Edge Alignment
Kit........................................................................................5
1.7.1. Installing Edge Alignment Kit...............6
3.4.1. Connecting external speakers........15
3.4.2. Connecting an external audio
device............................................................15
3.5. Connecting Multiple Displays in a Daisychain Configuration...............................................16
3.5.1. Display control connection...............16
3.5.2. Digital video connection.....................16
3.5.3. Analog video connection...................17
4. OSD Menu...............................................................18
4.1. Navigating the OSD Menu..............................18
4.1.1. Navigating the OSD menu using the
remote control........................................18
4.1.2. Navigating the OSD menu using the
display’s control buttons.....................18
4.2. OSD Menu Overview.........................................18
4.2.1. Picture menu.............................................18
4.2.2. Screen menu.............................................19
4.2.3. Audio menu...............................................20
4.2.4. PIP menu.....................................................20
4.2.5. Configuration1 menu...........................21
4.2.6. Configuration2 menu...........................22
4.2.7. Advanced option menu......................22
2. Parts and Functions.................................................. 8
2.1. Control Panel...............................................................8
2.2. Input/Output Terminals..........................................9
2.3. Remote Control......................................................10
2.3.1. General functions...................................10
2.3.2. Inserting the batteries in the remote
control..........................................................11
2.3.3. Handling the remote control...........11
2.3.4. Operating range of the remote
control..........................................................11
5. Input Mode...............................................................27
6. Pixel Defect Policy..................................................28
6.1. Pixels and Sub-Pixels.............................................28
6.2. Types of Pixel Defects + Dot Definition.. 28
6.3. Bright Dot Defects................................................28
6.4. Dark Dot Defects..................................................29
6.5. Proximity of Pixel Defects.................................29
6.6. Pixel Defect Tolerances.......................................29
6.7. MURA...........................................................................29
3. Connecting External Equipment.........................12
3.1. Using the Switch Cover......................................12
3.2. Connecting External Equipment (DVD/
VCR/VCD).................................................................13
3.2.1. Using COMPONENT video
input...............................................................13
3.2.2. Using Video Source input...................13
3.2.3. Using HDMI video input....................13
3.3. Connecting a PC.....................................................14
3.3.1. Using VGA input......................................14
3.3.2. Using DVI input.......................................14
3.3.3. Using HDMI input..................................14
3.3.4. Using DisplayPort input......................15
3.4. Connecting Audio Equipment.........................15
7.
Cleaning and Troubleshooting..............................30
7.1. Cleaning.......................................................................30
7.2. Troubleshooting.......................................................31
8. Technical Specifications.........................................32
ix
BDL4652EL
1.
Unpacking and Installation
1.1.
Unpacking
• This product is packed in a carton, together with the standard accessories.
• Any other optional accessories will be packed separately.
• Due to the size and weight of this display it is recommended for two people to move it.
• After opening the carton, ensure that the contents are complete and in good condition.
1.2.
Package Contents
Please verify that you received the following items with your package content:
• LCD display
POWER
• CD ROM
LCD Display
SMART
LCD-Display / Pantalla LCD / Écran LCD / Display LCD
AUDIO
SOURCE
BDL4252EL
BDL4652EL
PIP
• Remote control with AAA batteries
ON/OFF
INPUT
CONTRAST
CHANGE
BRIGHTNESS
DISPLAY
• Power cord (1.8 m)
MENU
SET
Kurzanleitung / Guía rápida / Guide de démarrage rapide / Guida rapida /
Instrukcja szybkiego uruchomienia / Краткое руководство по запуску /
Hızlı bașlangiç kılavuzu / 快速入门指南 / 快速入門指南
• VGA cable (1.8 m)
Installation / Installation / Instalación / Installation / Installazione / Instalacja /
Установка / Kurulum / 安装 / 安裝
Connect / Verbindungsfähigkeit / Conectividad / Connectivité / Connettività /
Połączenia / Подключение / Bağlantı / 连接性 / 連接性
AUTO
ADJUST
EXIT
VOL UP
CD ROM
MUTE
VOL DOWN
USB MENU
• RS232 cable (3 m)
Register your product and get support at
www.philips.com/welcome
Quick start guide
• Quick start guide
• Power switch cover
• Screw for Power switch cover (M3,
8mm x 1)
VIDEO
SOURCE
Wyświetlacz LCD / ЖК-монитор / LCD Ekran / 液晶显示器 / 液晶顯示器
Remote Control
and AAA Batteries
* The supplied power cord varies
depending on destination.
Thumb Screw
• Logo guider
• Edge Alignment Kit-1: 1PCS
Power switch cover
and screw (M3x8) x1
• Edge Alignment Kit-2: 2PCS
• Thumb Screw: 8PCS
Power Cord
RS232 Cable
Edge Alignment Kit-1
Video Signal Cable
(D-SUB to D-SUB Cable)
Edge Alignment Kit-2
Logo guider
NOTES:
• For all other regions, apply a power cord that conforms to the AC voltage of the power socket and has been approved by and complies with the
safety regulations of the particular country.
• You might like to save the package box and packing material for shipping the display.
1.3.
Installation Notes
• Due to the high power consumption, always use the plug exclusively designed for this product. If an extended line is required, please consult your
service agent.
• The product should be installed on a flat surface to avoid tipping. The distance between the back of the product and the wall should be maintained
for proper ventilation. Avoid installing the product in the kitchen, bathroom or any other places with high humidity so as not to shorten the service life
of the electronic components.
• The product can normally operate only under 3000m in altitude. In installations at altitudes above 3000m, some abnormalities may be experienced.
1
BDL4652EL
1.4.
Installing and Removing Table Stands (optional)
To install table stands:
1. Ensure your display is powered off.
2. Spread a protective sheet on a flat surface.
3. Grab the carrying handles and place the display face-down on the protective sheet.
4. After inserting the stand in the guide block, tighten the screws on both sides of the display.
NOTE: The longer side of the stand should face the front of the display.
Carrying handle
Thumbscrews
Longer portions face the front
Table stand
To remove table stands:
1. Power off the display.
2. Spread a protective sheet on a flat surface.
3. Grab the carrying handles and place the display face-down on the protective sheet.
4. Remove screws using a screwdriver and place them in a safe place for reuse.
2
BDL4652EL
1.5.
Mounting on a Wall
To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially available). We recommend using a mounting interface
that complies with TUV-GS and/or UL1678 standard in North America.
Protective Sheet
VESA Grid
Table
Tabletop stand
1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath the screen surface so as not to scratch the
screen face.
2. Ensure you have all accessories for mounting this display (wall mount, ceiling mount, table stand, etc).
3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the equipment
or injury to the user or installer. Product warranty does not cover damage caused by improper installation.
4. For the wall-mounting kit, use M6 mounting screws (having a length 10 mm longer than the thickness of the mounting bracket) and tighten them
securely.
1.5.1. VESA Grid
BDL4652EL
400(H) x 400(V) mm
400(H) x 200(V) mm
200(H) x 200(V) mm
Caution:
To prevent the display from falling:
• For wall or ceiling installation, we recommend installing the display with metal brackets which are commercially available. For detailed installation
instructions, refer to the guide received with the respective bracket.
• To lessen the probability of injury and damage resulting from fall of the display in case of earthquake or other natural disaster, be sure to consult the
bracket manufacturer for installation location.
Ventilation Requirements for enclosure locating
To allow heat to disperse, leave space between surrounding objects as shown in the
diagram below.
100 mm
100 mm
100 mm
100 mm
3
BDL4652EL
1.6.
Mounting in Portrait Position
This display can be installed in portrait position.
1. Remove the table stand, if attached.
2. Rotate 90 degrees clockwise. The “
” logo should be on the LEFT side when facing the display.
90
90
1.6.1. How to use the logo guider for portrait position
1. Put the guider on the lower-left corner of the front bezel of the display.
Fold down both of its edges.
2. Peel off the protective film at the back of the “
” logo sticker.
Hold and press the guider with your left hand. Put the “
” logo
sticker with its adhesive side down into the logo hole with your right
hand, and press to make it stick tightly onto the front bezel.
3. Remove the guider.
1.6.2. How to remove the logo
1. Prepare a piece of paper with a cutting area of logo as a protector to
prevent the front bezel from scratching.
1
2
3
2. Using a knife, carefully remove the logo sticker with the paper placing
beneath.
3. Tear off the logo sticker.
NOTE:
hen installing the display on a wall, please consult a professional technician for proper installation. We accept no liability for installations not
W
performed by a professional technician.
4
BDL4652EL
1.7.
Operating Instructions of Edge Alignment Kit
2
2
1
2
2
5
BDL4652EL
1.7.1. Installing Edge Alignment Kit
• Before install edge alignment kit, displays must be mounted to video wall frame correctly.
• Using “Thumb Screw” for easy installing.
• Using “Edge Alignment Kit-1” on adjacent four displays.
1
2
4
3
• Install the “Edge Alignment Kit-1” with 4 PCS of M4 screw.
1
2
4
3
6
BDL4652EL
• Using “Edge Alignment Kit-2” on adjacent two displays.
• Install the “Edge Alignment Kit-2” with 2 PCS of M4 screw.
7
BDL4652EL
2.
Parts and Functions
2.1.
Control Panel
9
MUTE INPUT
1
1
2
3
MENU
4
5
6
7
8
POWER button
NOTE:“Keyboard Control Lock Mode” This function completely
disables the access to all Keyboard Control functions. To
enable or disable the keyboard control lock, press both [ ]
and [ ] buttons and hold down continuously for more than
3 (three) seconds.
Use this button to turn the display on or put the display to standby.
2
MUTE button
Switch the audio mute ON/OFF.
3
9
INPUT button
• Receives command signals from the remote control.
• Use this button to select the input source.
4
• Indicates the operating status of the display without OPS:
[ ] button
-- Lights green when the display is turned on
Increase the adjustment while OSD menu is on, or increase the
audio output level while OSD menu is off.
-- Lights red when the display is in standby mode
-- Lights amber when the display enters APM mode
• Used as [SET] button in the On-Screen-Display menu,
5
-- When {SCHEDULE} is enabled, the light blinks green and red
[ ] button
-- If the light blinks red, it indicates that a failure has been
detected
Decrease the adjustment while OSD menu is on, or decrease the
audio output level while OSD menu is off.
6
-- Lights off when the main power of the display is turned off
[ ] button
• Indicates the operating status of the display with OPS:
Move the highlight bar up to adjust the selected item while OSD
menu is on.
7
-- Lights green when the display is on, but the OPS is off
-- Lights blue when the display and the OPS is on
[ ] button
-- Lights red when the display is in standby mode
-- Lights amber when the display enters APM mode
Move the highlight bar down to adjust the selected item while OSD
menu is on.
8
Remote control sensor and power status indicator
-- When {SCHEDULE} is enabled, the light blinks green and red
MENU button
-- If the light blinks red, it indicates that a failure has been
detected
Return to previous menu while OSD menu is on, or to activate the
OSD menu when OSD menu is off.
-- Lights off when the main power of the display is turned off
8
BDL4652EL
2.2.
Input/Output Terminals
21
20
19
18
17
2
1
1
8
3
4
5
6 7
13
9 10 11 12
AC IN
12 VGA
MAIN POWER SWITCH
13 VGA AUDIO
AC OUT
14 COMPONENT
IR pass through:
15 Y/CVBS
AC power input from the wall outlet.
2
Video source input.
16 SPEAKER
RS232C OUT
RS232C IN
RJ-45
20 OPS
OUT / VGA OUT
SLOT
21 KENSINGTON
DisplayPort video input.
11 DVI
OUT
Slot for installing the optional OPS module.
DisplayPort
IN
OUT (RCA)
External speakers output.
HDMI IN
10 DVI
18 AUDIO
19 SPEAKERS
HDMI video/audio input.
9
IN
Audio output from the AUDIO IN jack to an external AV device.
LAN control function for the use of remote control signal from
control center.
8
17 AUDIO
Audio input from external AV device (RCA).
RS232C network input for the loop-through function.
7
SWITCH
Internal speaker on/off switch.
RS232C network output for the loop-through function.
6
IN (BNC)
Component YPbPr video source input.
Outputs the remote control IR signal of set-top box to a external
set-top box through 3.5mm jack cable.
5
IN
Audio input for VGA source (3.5mm stereo phone).
AC power supply to the AC IN jack of a media player.
4
IN (D-Sub)
VGA video input.
Switch the main power on/off.
3
15
14 16
LOCK
Used for security and theft prevention.
DVI-D video input.
DVI or VGA video output.
9
BDL4652EL
2.3.
Remote Control
5
Press to turn on/off the information OSD displayed on the upper
right corner of the screen.
2.3.1. General functions
6
• Press to decrease the value in OSD menu.
1
10
VIDEO
SOURCE
• Press to move the sub-picture left in PIP mode.
AUDIO
SOURCE
2
7
8
12
NOTE: This button is functional for VGA input only.
3
INPUT
CHANGE
4
9
13
CONTRAST
BRIGHTNESS
5
DISPLAY
6
[AUTO ADJUST] button
Press to run the Auto Adjust function.
PIP
ON/OFF
[SET] button
Press to activate the setting inside the OSD menu.
11
10 [VIDEO
11 [AUDIO
17
AUTO
ADJUST
EXIT
VOL UP
MUTE
SOURCE] button
Press to toggle Video Source Menu. Press [ ] or [ ] button to
select one of the video sources among Displayport, DVI-D,
VGA, HDMI, Component, Video, or Card OPS. Press [SET]
button to confirm and exit.
16
7
8
[MUTE] button
Press to turn the mute function on/off.
14
15
MENU
SET
9
[ ] button
• Press to move the selection left in OSD menu.
POWER
SMART
[DISPLAY] button
SOURCE] button
Press to toggle Audio Source Menu. Press [ ] or [ ] button
to select one of the audio sources among Displayport, HDMI,
Audio1, Audio2, or Card OPS. Press [SET] button to confirm
and exit.
18
19
20
12 Picture
VOL DOWN
Format button
Press to switch screen aspect ratio.
21
USB MENU
• For PC signal: FULL, NORMAL, CUSTOM, and REAL.
• For Video signal: FULL, NORMAL, DYNAMIC, CUSTOM,
REAL, and 21:9.
13 [BRIGHTNESS]
button
Press to toggle Brightness Menu. Press [ ] or [ ] button to adjust
the value. Press [MENU] button to confirm and exit.
14 [
] button
• Press to move the selection up in OSD menu.
• Press to move the sub-picture up in PIP mode.
15 [MENU]
1
Press to switch on the display from standby mode. Press again to
turn it off and back into standby mode.
2
16 [
[SMART] button
• Press to increase the value in OSD menu.
• Press to move the sub-picture right in PIP mode.
17 [EXIT]
• Standard: Used for normal images (factory setting)
18 [
• sRGB: Used for text based images(only for PC mode)
] button
• Press to move the selection down in OSD menu.
• Cinema: Used for movies(only for Video mode)
• Press to move the sub-picture down in PIP mode.
[PIP] (Picture In Picture) button
[ON/OFF]: Turn PIP mode ON/OFF.
19 [VOL
UP] button
20 [VOL
DOWN] button
21 [USB
MENU] button
Press to increase the audio output level.
Select the input signal for the sub-picture.
[CHANGE]: Toggle between the main picture and sub picture.
4
button
Press to turn back to the previous OSD menu.
• Highbright: Used for moving image such as Video
[INPUT]:
] button
• Press to move the selection right in OSD menu.
Press to activate Smart Menu. Press [ ] or [ ] button to select
menu options. Press [SET] button to confirm and exit the selection.
3
button
Press to turn the OSD menu on/off.
[POWER] button
Press to decrease the audio output level.
[CONTRAST] button
Press to activate Contrast Menu. Press [ ] or [ ] button to adjust
the value. Press [MENU] button to confirm and exit.
This function is not available on this display.
10
BDL4652EL
2.3.2. Inserting the batteries in the remote control
The remote control is powered by two 1.5V AAA batteries.
To install or replace batteries:
1. Press and then slide the cover to open it.
2. Align the batteries according to the (+) and (–) indications inside the
battery compartment.
3. Replace the cover.
Caution:
The incorrect use of batteries can result in leaks or bursting. Be sure to follow these instructions:
• Place “AAA” batteries matching the (+) and (–) signs on each battery to the (+) and (–) signs of the battery compartment.
• Do not mix battery types.
• Do not combine new batteries with used ones. It causes shorter life or leakage of batteries.
• Remove the dead batteries immediately to prevent them from liquid leaking in the battery compartment. Don’t touch exposed battery acid, as it can
damage your skin.
NOTE:
If you do not intend to use the remote control for a long period, remove the batteries.
2.3.3. Handling the remote control
• Do not subject to strong shock.
• Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry immediately.
• Avoid exposure to heat and steam.
• Other than to install the batteries, do not open the remote control.
2.3.4. Operating range of the remote control
Point the top of the remote control toward the display’s remote control sensor when
pressing a button.
Use the remote control within a distance of less than 8m/26ft from the display’s sensor,
and a horizontal and vertical angle of less than 30 degrees.
NOTE:
he remote control may not function properly when the remote control
T
sensor on the display is under direct sunlight or strong illumination, or when
there is an obstacle in the path of signal transmission.
30
30
POWER
SMART
VIDEO
SOURCE
AUDIO
SOURCE
PIP
ON/OFF
INPUT
CONTRAST
CHANGE
BRIGHTNESS
DISPLAY
MENU
SET
AUTO
ADJUST
EXIT
VOL UP
MUTE
VOL DOWN
USB MENU
11
BDL4652EL
3.
Connecting External Equipment
3.1.
Using the Switch Cover
A cover for the power switch is provided to prevent the display from being turned on or off accidentally.
To lock the cover into position:
1. Align and insert the cover to the indentation located beside the power switch.
2. Use the screw to lock the cover.
12
BDL4652EL
3.2.
Connecting External Equipment (DVD/VCR/VCD)
3.2.1. Using COMPONENT video input
Audio Out
COMPONENT Out
(YPbPr)
DVD / VCR / VCD
[R]
[AUDIO IN]
[L]
[COMPONENT IN]
(YPbPr)
3.2.2. Using Video Source input
Audio Out
Y/CVBS Out
[R]
[L]
DVD / VCR / VCD
[AUDIO IN]
[Y/CVBS IN]
3.2.3. Using HDMI video input
DVD / VCR / VCD
HDMI Out
[HDMI IN]
13
BDL4652EL
3.3.
Connecting a PC
3.3.1. Using VGA input
VGA Out
D-Sub 15 pin
PC
[R]
Audio Out
[L]
[AUDIO IN]
[VGA IN]
[VGA AUDIO IN]
3.3.2. Using DVI input
DVI Out
PC
[R]
Audio Out
[L]
[AUDIO IN]
[DVI IN]
[VGA AUDIO IN]
3.3.3. Using HDMI input
HDMI Out
PC
[HDMI IN]
14
BDL4652EL
3.3.4. Using DisplayPort input
DisplayPort Out
PC
[DisplayPort IN]
3.4.
Connecting Audio Equipment
3.4.1. Connecting external speakers
External speakers
3.4.2. Connecting an external audio device
Audio In
[R]
[L]
[AUDIO OUT]
15
Stereo Amplifier
BDL4652EL
3.5.
Connecting Multiple Displays in a Daisy-chain Configuration
You can interconnect multiple displays to create a daisy-chain configuration for applications such as a video wall.
NOTE:
Maximum 25 displays (5x5) can be used in a daisy-chain configuration.
3.5.1. Display control connection
Connect the [RS232C OUT] connector of DISPLAY 1 to the [RS232C IN] connector of DISPLAY 2.
PC
[RS-232C]
DISPLAY 1
[RS-232C IN]
DISPLAY 2
[RS-232C OUT]
[RS-232C IN]
3.5.2. Digital video connection
Connect the [DVI OUT / VGA OUT] connector of DISPLAY 1 to the [DVI IN] connector of DISPLAY 2.
PC
[DVI]
DISPLAY 1
[DVI IN]
DISPLAY 2
[DVI/VGA OUT]
[DVI IN]
Connect the [HDMI OUT ] connector of DISPLAY 1 to the [DVI IN] connector of DISPLAY 2.
DISPLAY 1
DVD / VCR / VCD
[HDMI]
[DVI IN]
DISPLAY 2
[DVI OUT]
16
[DVI IN]
BDL4652EL
3.5.3. Analog video connection
Connect the [DVI OUT / VGA OUT] connector of DISPLAY 1 to the [VGA IN] connector of DISPLAY 2.
PC
[VGA]
DISPLAY 1
[VGA IN]
DISPLAY 2
[DVI/VGA OUT]
17
[VGA IN]
BDL4652EL
4.
OSD Menu
4.2.
An overall view of the On-Screen Display (OSD) structure is shown
below. You can use it as a reference for further adjusting your display.
4.1.
OSD Menu Overview
4.2.1. Picture menu
Navigating the OSD Menu
Picture
Contrast
Screen
4.1.1. Navigating the OSD menu using the
remote control
Audio
Configuration1
Black level
Tint
Color
Color temperature
MENU
Configuration2
Advanced option
SET
Color control
Smart contrast
Smart picture
Brightness
EXIT
Adjust the overall image brightness by changing the intensity of the LCD
panel’s backlight.
1. Press [MENU] button on the remote control to display the OSD
menu.
] or [
Sharpness
Noise reduction
PIP
2. Press [
Brightness
Contrast
Adjust to sharpen the picture quality. The black portions of the picture
become richer in darkness and the white become brighter.
] button to choose the item you want to adjust.
3. Press [SET] or [ ] button to enter the submenu.
Sharpness
4. In the submenu, press [ ] or [ ] button to toggle among items,
press [ ] or [ ] button to adjust settings. If there is a submenu,
press [SET] or [ ] button to enter the submenu.
Adjust to improve the image detail.
Black level
Video black level is defined as the level of brightness at the darkest
(black) part of a visual image. Adjust to change the image brightness.
5. Press [EXIT] button to return to the previous menu, or press
[MENU] button to exit the OSD menu.
Noise reduction
Adjust to remove the noise in the image. You can select a suitable noise
reduction level.
4.1.2. Navigating the OSD menu using the
display’s control buttons
Choose from: {Off} / {Low} / {Medium} / {High}.
1. Press [MENU] button to display the OSD menu.
NOTE:
2. Press [ ] or [ ] button to choose the item you want to adjust.
3. Press [ ] button to enter the submenu.
his item is functional for HDMI(Video mode), Video, and
T
YPbPr inputs only.
Tint
4. In the submenu, press [ ] or [ ] button to toggle among items,
press [ ] or [ ] button to adjust settings. If there is a submenu,
press [ ] button to enter the submenu.
Adjust to change the color tint of the image.
Use the [ ] or [ ] button to adjust. Press the [ ] button and the
flesh tone color turns slightly green. Press the [ ] button and the flesh
tone color turns slightly purple.
5. Press [MENU] button to return to the previous menu, or press
[MENU] button several times to exit the OSD menu.
NOTE:
his item is functional for HDMI(Video mode), Video, and
T
YPbPr inputs only.
Color
Adjust to increase or decrease the intensity of colors in the image.
NOTE:
his item is functional for HDMI(Video mode),Video and
T
YPbPr inputs only.
Color temperature
Select a color temperature for the image. A lower color temperature
will have a reddish tint, whilst a higher color temperature gives off a
more bluish tint.
Choose from: {3000K} / {4000K} / {5000K} / {6500K} / {7500K} /
{9300K} / {10000K} / {Native} / {User}.
Color control
With this function you can adjust the color tones of the image precisely
by changing the R (Red), G (Green) and B (Blue) settings independently.
18
BDL4652EL
NOTE:
This item is functional only when {Color temperature} is set
to {User}.
Clock
Adjust the width of the image.
This item is functional for VGA input only.
Smart contrast
NOTE:
Smart contrast function is to enhance image contrast on darker scenes
when activated. The Brightness setting in the Picture menu will be
disabled when Smart Contrast is activated.
Clock phase
Adjust to improve the focus, clarity and stability of the image.
NOTE:
Smart picture
This item is functional for VGA input only.
Zoom mode
The following smart picture modes are available for:
The pictures you receive may be transmitted in 16:9 format (wide
screen) or 4:3 format (conventional screen). The 16:9 pictures
sometimes have a black band at the top and bottom of the screen
(letterbox format). Zoom Mode will be deactivated when Pixel Shift is
activated or turned on.
• PC mode: {Standard} / {Highbright} / {sRGB}.
• Video mode: {Standard} / {Highbright} / {Cinema}.
Video source
Select a video input source.
This function allows you to optimize the picture display on screen. The
following zoom modes are available for:
 

• PC mode: {Full} / {Normal} / {Custom} / {Real}.
• Video mode: {Full} / {Normal} / {Dynamic} / {Custom} / {Real} /
{21:9}.


Full


This mode restores the correct proportions
of pictures transmitted in 16:9 using the full
screen display.
 
Normal

The picture is reproduced in 4:3 format and
a black band is displayed on either side of the
picture.
Picture reset
Reset all settings in the Picture menu.
Dynamic
Fill the entire screen by stretching 4:3 pictures
non-proportionally.
4.2.2. Screen menu
Picture
H position
Custom
V position
Screen
Clock
Audio
Clock phase
Choose to apply the custom zoom settings in
the Custom Zoom submenu.
Zoom mode
PIP
Configuration1
Real
Custom zoom
This mode displays the image pixel-by-pixel
on screen without scaling the original image
size.
Screen reset
Configuration2
21:9
The picture is enlarged to 16:9 format. This
mode is recommended when displaying
pictures that have black bands at the top and
bottom (letterbox format).
Advanced option
H position
Custom zoom
Press the [ ] button to move the image to the right, or [ ] to move
the image to the left.
You can use this function to further customize the zoom settings to suit
the image you want to display.
NOTE:
NOTE:
• H position adjustment is functional on all inputs, except HDMI, Card
OPS, and DP In.
Zoom
• H position cannot be adjusted when Pixel Shift is activated.
Expands the horizontal and vertical sizes of the
image simultaneously.
V position
Press the [ ] button to move the image up, or [ ] to move the image
down.
NOTE:
his item is functional only when the Zoom mode setting is
T
set to Custom.
H zoom
Expands the horizontal size of the image only.
• V position adjustment is functional on all inputs, except HDMI, Card
OPS, and DP In.
• V position cannot be adjusted when Pixel Shift is activated.
19
BDL4652EL
Audio source
V zoom
Select the audio input source according to the audio signal source
connected to the audio input and HDMI sockets on the display.
Expands the vertical size of the image only.
 
H position

Moves the horizontal position of the image left
or right.


V position

Moves the vertical position of the image up or
down.
 
Screen reset
Choose from: {Displayport } / {HDMI} / {Audio1} / {Audio2} / {Card
OPS}.
Reset all settings in the Screen menu to factory preset values.
Audio reset
Reset all settings in the Audio menu to factory preset values.
4.2.3. Audio menu
Picture
Card OPS audio
Select the analog or digital audio mode for card OPS.
Balance
Treble
Screen
Bass
Audio
Volume
4.2.4. PIP menu
Maximum volume
PIP
Configuration1
Picture
Screen
Mute
Audio source
Configuration2
Advanced option
PIP
PIP input
Minimum volume
Audio
PIP change
PIP size
PIP audio
Audio reset
PIP
Card OPS audio
PIP reset
Configuration1
Configuration2
Balance
Advanced option
Adjust to emphasize left or right audio output balance.
Treble
Adjust to increase or decrease higher-pitched sounds.
PIP
Bass
Select the PIP (Picture-in-Picture) mode.
Adjust to increase or decrease lower-pitched sounds.
Choose from: {Off} / {PIP} / {POP} / {PBP aspect} / {PBP full}.
Volume
PIP input
Adjust to increase or decrease the audio output level.
Select the input signal for the sub-picture.
Maximum volume
PIP change
Adjust your own limitation for the maximum volume setting. This stops
the volume from being playing at too loud a level.
Enlarges the smaller picture to become the main picture, and vice versa.
Minimum volume
Select the size of the sub picture in the PIP (Picture-in-Picture) mode.
PIP size
Adjust your own limitation for the minimum volume setting.
Choose from: {Small} / {Medium} / {Large}.
Mute
PIP audio
Turn the mute function on/off.
Select the audio source in the PIP (Picture-in-Picture) mode.
• {Main} - Select audio from the main picture
• {Sub} - Select audio from the sub picture.
PIP reset
Reset all settings in the PIP menu to factory preset values.
NOTES:
• The PIP function is available only for the following condition:
{Configuration1} - {Panel saving} - {Pixel shift} setting to [Off] and
{Advanced option} - {Tiling} - {Enable} setting to [No].
20
BDL4652EL
• The PIP function is available only for certain signal source
combinations as shown in the table below.
Power save
• The availability of the PIP function will also depend on the resolution
of the input signal being used.
• {RGB} - Select {On} to let the display enter APM mode when no
signal is detected from the HDMI Graphic mode, HDMI, DVI-D, or
VGA inputs after three successive cycles.
Main Picture
Sub Picture
Displayport
HDMI
DVI-D
VGA
YPbPr
Video
Card OPS
Displayport
HDMI
DVI-D
VGA
YPbPr
Video
Card
OPS
X
X
X
O
O
O
X
X
X
X
O
O
O
X
X
X
X
O
O
O
X
O
O
O
X
X
X
O
O
O
O
X
X
X
O
O
O
O
X
X
X
O
X
X
X
O
O
O
X
Use this setting to reduce the power automatically.
• {VIDEO} - Select {On} to enter power saving mode when no signal
is detected from the HDMI Video mode or YPbPr inputs after three
successive cycles.
Language
Select the language used in the OSD menu.
The options are: {
}/{
{
}/{
}/{
(O: PIP function available, X: PIP function unavailable)
By pressing the [PIP ON/OFF] button on the remote control, you can
change the mode in the order shown below:
PIP
PBP aspect
POP
PBP full
}/{
} / { 简体中文 } / {
}/
}/{
} / { 繁體中文 } .
Panel saving
Choose to enable the panel saving functions and thus reduce the risk of
“image persistence” or “ghost-imaging”.
Off
• {Cooling Fan} - Select {On} to turn on the cooling fan all the
time. Select {Auto} to turn on/off the cooling fan according to the
display’s temperature.
The resolutions in the PIP and POP modes are configured as follows:
PIP SIZE {Small}
NOTES:
• The default {Auto} option will start running the cooling fan if
the temperature of 60°C (140°F) is reached, and stop running
the cooling fan if the temperature of 58°C (136°F).
: 320 x 240 pixels
{Medium} : 480 x 320 pixels
{Large}
: 640 x 480 pixels
• A temperature-warning message will be shown on the screen if
the temperature reaches 79°C (174°F). All key functions except
[Power] key will then be disabled.
POP SIZE: 474 x 355 pixels
NOTE:
The images displayed in the sub picture always fit the PIP
sizes shown above irrespective of the aspect ratio of the input
image.
• Once the temperature reaches 80°C (176°F), the display power
will be shut down automatically.
• {Brightness} - Select {On} and the image brightness will be reduced
to an appropriate level. The Brightness setting in the Picture menu
will be unavailable when selected.
4.2.5. Configuration1 menu
Picture
Switch on state
• {Pixel shift} - Select the time interval ({Auto} / {10 ~ 900} Seconds
/ {Off}) for the display to slightly expand the image size and shift
the position of pixels in four directions (up, down, left, or right).
Activating Pixel Shift will disable H Position, V Position and Zoom
Mode in the Screen Menu.
Auto adjust
Screen
Audio
Power save
Language
Panel saving
PIP
Configuration1
Color system
Color system
Network control port
Selects the Color System depending on your input video format.
Network settings
Configuration2
Advanced option
The options are: {Auto} / {NTSC} / {PAL} / {SECAM} / {4.43NTSC} /
{PAL-60}.
Configuration reset
Factory reset
NOTE:
This item is functional for VIDEO input only.
Network control port
Select the network control port.
Switch on state
Choose from: {RS232} / {LAN(RJ45)} / {Card OPS RS232}.
Select the display status used for the next time you connect the power
cord.
NOTES:
• If {LAN(RJ45)} is selected, then {RS232} will not be activated, even
if a cable is attached, and vice versa.
• {Power off} - The display will remain off when the power cord is
connected to a wall outlet.
• The option {Card OPS RS232} is functional after connected with
your OPS device.
• {Forced on} - The display will turn on when the power cord is
connected to a wall outlet.
• {Last status} - The display will return to the previous power status
(on/off/standby) when removing and replacing the power cord.
Auto adjust
Use this function to automatically optimize the display of VGA input
image.
NOTE:
This item is functional for VGA input only.
21
BDL4652EL
Network settings
OSD turn off
Assign {IP address}, {Subnet Mask}, and {Default gateway} for the
display.
Set the period of time the OSD (on-screen display) menu stays on the
screen.
The options are: {5 ~ 120} seconds.
Network settings
Information OSD
0
9
Network host name
Set the period of time the information OSD is displayed on the upper
right corner of the screen. The information OSD will display when input
signal is changed.
L
Z
The information OSD will remain on the screen with {Off} selection.
Disable
DHCP
-
0
-
1
The options are: {1 ~ 60} seconds.
255 - 255 -
0
-
0
-
0
-
0
Off Timer
16
172 -
IP address
Subnet mask
0
-
0
Default gateway
Set the display to turn itself off to standby mode within an amount of
time specified.
a d m i n
Login user name
0
Login password
0
0
0
The options are: {Off, 1 ~ 24} hours from currrent time.
[ SET ]
NOTE:
change [SET] in STORE
hen the “Off timer” is activated, the “Schedule” settings will
W
be disabled.
OSD H-position
• DHCP - Choose to enable or disable the DHCP function. If enabled,
the display will be assigned IP address, Subnet mask and Default
gateway automatically. If disabled, you will be prompted to enter
the following values manually. When finished, press [SET] button to
store and save the chosen values.
• IP address
• Subnet mask
• Default gateway
• Login user name (The default user name is {admin})
• Login password (The default password is {0000})
Adjust the horizontal position of the OSD menu.
OSD V-position
Adjust the vertical position of the OSD menu.
Monitor information
Shows information about your display, including model number, serial
number, operating hours and software version.
Monitor information
Configuration reset
Reset all settings in Configuration1 menu to the factory preset values.
Model name:
Serial no:
Operation hours:
SW Version:
Factory reset
Reset all settings in the OSD menus of {Picture}, {Screen}, {Audio}, {PIP},
{Configuration1}, {Configuration2}, and {Advanced option} to the
factory preset values.
BDL4652EL
0H
3M
VER 0.204
4.2.7. Advanced option menu
Press [ ] or [ ] button to select [Reset], and then press [SET] button
to do the reset.
Picture
Factory reset
Input resolution
HDMI clock threshold
Screen
Audio
Black level expansion
Gamma selection
Scan mode
PIP
Reset
Cancel
Configuration1
Scan conversion
Film mode
IR control
4.2.6. Configuration2 menu
Configuration2
Advanced option
Picture
OSD turn off
Keyboard control
Tiling
Heat status
Information OSD
Screen
Audio
PIP
Off timer
OSD H-position
Input resolution
OSD V-position
Set the resolution of the VGA input. This is only required when the
display is unable to detect the VGA input resolution correctly.
Monitor information
This item is functional for VGA input only.
Configuration1
NOTE:
Configuration2
The options are:
• {1024x768 / 1280x768 / 1360x768 / 1366x768}
Advanced option
• {1400x1050 / 1680x1050}
• {1600x1200 / 1920x1200}
• {Auto}: Determines the resolution automatically.
22
BDL4652EL
The selected settings will become effective after turning off the power
and turning it on again.
• {Secondary} - Designate this display as the secondary display. This
display can not be operated by the remote control, and will only
receive the control signal from the primary display via the RS232C
connection.
HDMI clock threshold
Adjust HDMI link clock.
• {Lock All} / {Lock all but Volume} / {Lock all but Power} - Lock the
remote control function of this display. To unlock, press and hold the
[DISPLAY] button on the remote control for 5 (five) seconds..
• {Min} - 800KHz.(Default)
• {Max} - 5000KHz.
NOTE: T
hreshold clock is for HDMI signals only. HDMI Threshold
clock applies to the deviation of HDMI pixel clock. At times,
HDMI pixel clock from some devices may not be stable. The display may treat the unstable signal as video mode
change and mute the video. Threshold clock allows for the
adjustment of the clock tolerance to avoid video mute.
Keyboard control
Choose to enable or disable the display keyboard (control buttons)
function.
• {Unlock} - Enable the keyboard function.
• {Lock All} / {Lock all but Volume} / {Lock all but Power} - Disable
the keyboard function.
Black level expansion
Tiling
This feature offers deeper blacks for an even better image quality.
With this function you can create a single large-screen matrix (video
wall) that consists of up to 25 sets of this display (up to 5-sets each on
the vertical and horizontal side). This function requires a daisy-chain
connection.
The options are: {Off} / {Low} / {Medium} / {High}.
NOTE:
This item is functional for Video mode input only.
Gamma selection
Gamma is what controls the overall brightness of an image. Images
which are not corrected properly can appear too white or too dark, so
controlling the gamma properly can have a huge influence on the overall
picture quality of your display.
Tiling
1
V monitors
1
Position
The options are: {Native} / {2.2} / {2.4} / {S gamma}.
Scan mode
Change the display area of the image.
• {Overscan} - Display about 95% of the original size of the image.
The rest of the areas surrounding the image will be cut off.
1
Frame comp.
No
Enable
No
Switch on delay
Off
Example: 2 x 2 screen matrix (4 displays)
H monitors = 2 displays
V monitors = 2 displays
• {Underscan} - Display the image in its original size.
NOTE:
H monitors
This item is functional for Video mode input only.
H monitors
Scan conversion
Choose to enable or disable the IP (Interlace to Progressive) conversion
function.
V monitors
• {Progressive} - Enable the IP conversion function (recommended).
Once enabled, the interlace input signal will be converted to
progressive format for better display quality.
• {Interlace} - Disable the IP function. This mode is suitable for
displaying motion pictures, but it increases the chance of image
retention.
Film mode
Choose to turn on or off the film mode frame conversion function.
1
2
3
4
Position
Example: 5 x 5 screen matrix (25 displays)
H monitors = 5 displays
V monitors = 5 displays
• {Auto} - Enable the film mode frame conversion function for
movies and motion pictures. The display converts a 24 frames-persecond (24 fps) input signal format to DVD video signal format.
Once this function is enabled, it is recommended that you set the
{Scan conversion} function to {Progressive}.
H monitors
• {Off} - Disable the film mode frame conversion function. This mode
is suitable for TV broadcasting and VCR signals.
V monitors
IR control
Select the operation mode of the remote control when multiple
displays are connected via an RS232C connection.
• {Normal} - All displays can be operated normally by the remote
control unit.
• {Primary} - Designate this display as the primary display for remote
control operation. Only this display can be operated by the remote
control.
1
2
3
4
5
6
11
7
12
8
13
9
14
10
15
16
21
17
22
18
23
19
24
20
25
Position
• H monitors - Select the number of displays on the horizontal side.
23
BDL4652EL
• V monitors - Select the number of displays on the vertical side.
Date and time
• Position - Select the position of this display in the screen matrix.
Adjust the current date and time for the display’s internal clock.
• Frame comp. - Choose to turn the frame compensation function
on or off. If selected {Yes}, the display will adjust the image to
compensate for the width of the display bezels in order to
accurately display the image.
Date and time
Year
Frame comp. - Yes
2012
Month
08
Day
04
Hour
20
Minute
20
Daylight saving time
Current date time
2012 . 08 . 04
20 : 20 : 17
Press [SET] to set clock
1. Press [ ] button to enter the submenu.
2. Press [ ] or [ ] button to toggle between {Year}, {Month}, {Day},
{Hour}, {Minute}, and {Daylight saving time}.
3. Press [ ] or [ ] button to adjust all settings except {Daylight
saving time}.
Frame comp. - No
4. Press [SET] button to enter the {Daylight saving} submenu.
5. Press [ ] or [ ] button to select item, press [
to adjust.
] or [
] button
Schedule
This function allows you to program up to 7 (seven) different scheduled
time intervals for the display to activate.
You can select:
• The time for the display to turn on and turn off.
• The days in a week for the display to activate.
• Which input source the display will use for each scheduled
activation period.
NOTE:
• Enable: Choose to enable or disable the Tiling function. If enabled,
the display will apply the settings in {H monitors}, {V monitors},
{Position}, and {Frame comp.}.
1. Press [SET] or [ ] button to enter the submenu.
• Switch on delay: Set the power-on delaying time (in seconds). The
default option {Auto} allows a sequential powering-on for each
display by their ID number when multiple displays are connected.
The options are: {Off / Auto / 2, 4, 6, 8, 10, 20, 30, 40, 50}
NOTE:
e recommend you to set up current date and time in the
W
{Date and time} menu before using this function.
Schedule
he Tiling function will be disabled when the [ON/OFF]
T
button for PIP is pressed.
Today
1
2
3
4
5
6
7
Heat status
This function allows you to check the thermal status of the display at
any time.
24
2012 . 08 . 04
On
_:_
Every day
Wed
SAT
THU
Off
_:_
MON
THU
SUN
20 : 19 : 55
Input
_
TUE
FRI
Every week
BDL4652EL
2. Press [ ] or [ ] button to select a schedule item (item number 1
~ 7), and then press [ ] button to mark it the item number.
a rotation sensor in the monitor enables the operating system to keep
the display upright as the monitor is moved between its portrait and
landscape positions.
The following DDC/CI commands should be supported via command
line:
Schedule
Today
1
2
3
4
5
6
7
2012 . 08 . 04
On
_:_
1
Every day
Wed
SAT
Off
_:_
THU
2
MON
THU
SUN
20 : 19 : 55
Input
_
3
TUE
FRI
Every week
4
3. Press [ ] or [ ] button to select the schedule:
1 P
ower-on schedule: Press [ ] or [ ] button to set the hour
and minute for the display to turn on.
2
4
Commands
Set Brightness
set Contrast
Set Red Gain
Set Green Gain
Set Blue Gain
Get Brightness
7
8
9
10
Get Contrast
Get Red Gain
Get Green Gain
Get Blue
HDMI with One Wire
CEC control.
• {Off} - Disable CEC.(Default)
Power-off
schedule: Press [ ] or [ ] button to set the hour
and minute for the display to turn off.
• {On} - Enable CEC.
Select or leave an empty “__” for both the hour and minute slot if
you do not want to use this power-on or power-off schedule.
3
No.
1
2
3
4
5
6
Smart power
Set the display to reduce the power consumption automatically.
Input-source selection: Press [ ] or [ ] button to select an
input source. If no input source is selected, the input source
will remain the same as last selected.
The options are: {Off} / {Medium} / {High}.
Auto signal detection
Choose to let the display detect and display available signal sources
automatically.
Date schedule: Press [ ] button to select which day in a
week this schedule item will be take effect, and then press the
[SET] button.
• {Off} - Once a signal is connected, it can only be selected manually.
No signal, set the display to display the image automatically according to
the search order of each option.
4. For additional schedule settings, press [EXIT], then repeat the steps
above. A check mark in the box next to the number of the schedule
item indicates that the selected schedule is in effect.
The options are: {All} / {PC source only} / {Video source only} /
{Failover}
NOTES:
• {All} - Search order: DP -> DVI-> VGA -> HDMI -> Component->
Video -> Card OPS.
• The {Every day} selection in a schedule item takes priority over the
other weekly schedules.
• {PC source only} - Search order: DP -> DVI -> VGA -> HDMI ->
Card OPS.
• If the schedules overlap, the scheduled power-on time takes priority
over scheduled power-off time.
• {Video source only} - Search order: HDMI -> Component ->
Video
• If there are two schedule items programmed for the same time, the
highest numbered schedule takes priority. For example, if schedule
items #1 and #2 both set the display to power on at 7:00 AM and
off at 5:00 PM, then only schedule item # 1 will take effect.
• {Failover}
-- Failover is the function of auto switching to the backup (failover)
input in the event a failure or abnormal termination of the
primary (main) input device occurs. (PC or media player failure)
Monitor ID
Set the ID number for controlling the display via the RS232C
connection. Each display must have a unique ID number when multiple
sets of this display are connected. Monitor ID number range is between
1 to 26.
-- The failover input, can be directed to any input on the display
other than the primary. (Ex, Primary = HDMI, Failover = DVI,
VGA)
-- With Failover activated, in the event of a primary input device
failure, the display will automatically switch to the Failover input
and display the content that is being played on the backup input. DDC/CI
Choose to turn on or off the DDC/CI communication function. Select
{On} for normal use.
-- When primary (main) input is back on, the failover mode will
need to be reset manually in order to perform the failover
function again. The failover will automatically switch off after
primary (main) input has returned to normal operating status.
DDC/CI (Command Interface) specifies a means for a computer to
send commands to the monitor, as well as receive sensor data from the
monitor, over the bidirectional link such as DDC2Ab/Bi/B+.
Specific commands to control monitors are defined in a separate
Monitor Control Command Set (MCCS) standard.
-- Main input(selected by user), default is HDMI. Failover input
input(selected by user), default is VGA.
DDC/CI monitors are sometimes supplied with an external color
sensor to allow automatic calibration of the monitor’s color balance.
Some tilting DDC/CI monitors support an auto pivot function, where
25
BDL4652EL
NOTE:
• The primary input signal to display priority, and this item is functional
for Primary input signal only.
• Auto search is functional for No signal only. If the user set the input
source manually, the display is based on the users set priority.
APM
Power save setting.
• {Off} - No signal, direct shutdown. ( Default )
• {On} - No signal, enter into Power Save mode.
OPS settings
Set the OPS configuration under each power condition.
• {Auto} - After selecting {Card OPS} for video source input, the
OPS will be set to off when the display power is set to off, or set to
on when the display power is set to on. When set to other video
source inputs, the OPS will always be set to on.
• {Always off} - The OPS will always be set to off.
• {Always on} - The OPS will always be set to on.
Advanced option reset
Reset all settings in the Advanced option menu to factory preset values.
1. Press [SET] or [ ] button to enter the submenu.
2. Press [ ] or [ ] button to select {Reset} and press the [SET]
button to restore settings to factory preset values.
3. Press the [EXIT] button or select {Cancel} and press the [SET]
button to cancel and then return to the previous menu.
Picture
Screen
Audio
PIP
Configuration1
Configuration2
Advanced option
Date and time
Action
Schecule
Action
Monitor ID
Action
DDC/CI
On
HDMI with One Wire
Off
Smart power
Off
Auto signal detection
Action
APM
Off
OPS settings
Always on
Advanced option reset
Action
26
BDL4652EL
5.
Input Mode
VGA Resolution:
Standard
Resolution
VGA
WVGA
SVGA
XGA
WXGA
WXGA
SXGA
SXGA
WXGA
WXGA
UXGA
HD1080
Active Resolution
H Pixels
V Lines
480
640
72 Hz
75 Hz
720
400
600
800
75 Hz
768
1024
75 Hz
1280
768
1280
800
1280
960
1280
1024
1360
768
1366
768
1600
1200
1920
1080
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
60 Hz
72 Hz
75 Hz
70 Hz
60 Hz
75 Hz
60 Hz
75 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
25.175 MHz
31.5 MHz
31.5 MHz
33.75 MHz
40 MHz
49.5 MHz
65 MHz
78.75 MHz
79.5 MHz
79.5 MHz
108 MHz
108 MHz
85.5 MHz
85.5 MHz
162 MHz
148.5 MHz
4:3
Video Graphic Array
16:9
Wide Video Graphic Array
4:3
Super VGA
4:3
Extended Graphic Array
5:3
16:10
4:3
5:4
16:9
16:9
4:3
16:9
Wide XGA
Wide XGA
Super XGA
Super XGA
Wide XGA
Wide XGA
Ultra XGA
HD1080
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
29.97 Hz
59.94 Hz
25 Hz
50 Hz
13.5 MHz
27 MHz
13.5 MHz
27 MHz
4:3
Modified NTSC Standard
4:3
Modified PAL Standard
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
74.25 MHz
16:9
Normally DVB Mode
74.25 MHz
16:9
Normally ATSC Mode
148.5 MHz
16:9
Normally ATSC Mode
SDTV Resolution:
Standard
Resolution
480i
480p
576i
576p
Active Resolution
H Pixels
V Lines
720
480
720
480
HDTV Resolution:
Standard
Resolution
Active Resolution
H Pixels
V Lines
720p
1280
720
1080i
1920
1080
1080p
1920
1080
50 Hz
60 Hz
25 Hz
30 Hz
50 Hz
60 Hz
• The PC text quality is optimum in HD 1080 mode (1920 x 1080, 60Hz).
• Your PC display screen might appear different depending on the manufacturer (and your particular version of Windows).
• Check your PC instruction book for information about connecting your PC to a display.
• If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5KHz (horizontal). In some cases, abnormal signals (such as
stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the [INPUT] button to enter the
video mode. Also, make sure that the PC is connected.
• When horizontal synchronous signals seem irregular in RGB mode, check PC power saving mode or cable connections.
• The display settings table complies to the IBM/VESA standards, and based on the analog input.
• The DVI support mode is regarded as same to the PC support mode.
• The best timing for the vertical frequency to each mode is 60Hz.
27
BDL4652EL
6.
Pixel Defect Policy
We strive to deliver the highest quality products and use some of the industry’s most advanced manufacturing processes whilst practicing stringent quality
control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays are sometimes unavoidable. No manufacturer can
guarantee that all panels will be free from pixel defects, but Philips guarantees that any Plasma- & LCD- displays with an unacceptable number of defects
will be repaired during the warranty period in line with your local guarantee conditions.
This notice explains the different types of pixel defects and defines the acceptable defect level for the LCD screen. In order to qualify for repair under
warranty, the number of pixel defects must exceed a certain level as shown in the reference table. If the LCD screen is within specification a warranty
exchange / claim back will be refused. Additionally, because some types or combinations of pixel defects are more noticeable than others, Philips sets even
higher quality standards for those.
6.1.
Pixels and Sub-Pixels
A pixel, or picture element, is composed of three sub-pixels in the primary colors of red, green and
blue. Many pixels together form an image. When all sub-pixels of a pixel are lit, the three colored
sub-pixels together appear as a single white pixel. When all are dark, the three colored sub-pixels
together appear as a single black pixel. Other combinations of lit and dark sub-pixels appear as
single pixels of other colors.
subpixel
pixel
6.2.
Types of Pixel Defects + Dot Definition
Pixel and sub-pixel defects appear on the screen in different ways. There are three categories of pixel defects and several types of sub-pixel defects within
each category.
Dot definition = What is a defective “Dot”? :
One or more defective, adjacent sub-pixel are defined as one “dot”. The no. of defective sub-pixels are not relevant to define a defective dot. This means
that a defective dot can consist of one, two or three defective sub-pixels which can be dark or lit.
R G B
One dot = One Pixel; consists of three sub-pixels of Red, Green, and Blue.
6.3.
Bright Dot Defects
Bright dot defects appear as pixels or sub-pixels that are always lit or “on”. These are the examples of bright dot defects:
One lit red, green or blue sub pixel
Two adjacent lit sub pixels:
Red + Blue = Purple
Red + Green = Yellow
Green + Blue = Cyan (Light Blue)
28
Three adjacent lit sub pixels (one white pixel)
BDL4652EL
6.4.
Dark Dot Defects
Black dot defects appear as pixels or sub-pixels that are always dark or “off ”. These are the examples of black dot defects:
One dark dot
6.5.
Two adjacent dark dots = 1 pair of dark dots
Two dark dots, specifications defines the
minimum distance between dark dots
Proximity of Pixel Defects
Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also specifies tolerances for the
proximity of pixel defects. In the table below you can find specifications about:
• Allowed amount of adjacent dark dots = (adjacent dark dots =1 pair of dark dots)
• Minimum distance between dark dots
• Total no. of all defective dots
6.6.
Pixel Defect Tolerances
In order to qualify for repair due to pixel defects during the warranty period, a PDP / TFT panel in a Philips Plasma / LCD- display must have pixel or subpixel defects exceeding the tolerances listed in the following table.
BRIGHT DOT EFFECT
ACCEPTABLE LEVEL
1 lit sub pixel
2
BLACK DOT EFFECT
ACCEPTABLE LEVEL
1 dark sub pixel
10
TOTAL DOT DEFECTS OF ALL TYPES
12
NOTE: * 1 or 2 adjacent sub pixel defects = 1 dot defect
6.7.
MURA
Dark spots or patches may occasionally appear on some liquid crystal display (LCD) panels. This is known within the industry as Mura, which is a Japanese
term for “unevenness.” It is used to describe an irregular pattern or area in which uneven screen uniformity appears under certain conditions. Mura is a
result of the deterioration of the liquid crystal alignment layer and is most commonly caused by long-term operation under high ambient temperatures. It
is an industry- wide phenomenon and Mura is not repairable. It is also not covered by our warranty terms.
Mura has been around since the introduction of LCD technology and with screens getting bigger and in operation 24/7, many displays are running in low
light conditions. This all adds to the possibility of Mura affecting displays.
HOW TO SPOT MURA
There are many symptoms of Mura and also multiple causes. Several of these are listed below:
• Impurities or foreign particles in the crystal matrix
• Uneven distribution of LCD matrix during manufacturing
• Non-uniform luminance distribution of the backlight
• Panel assembly induced stress
• Flaws within the LCD cells
• Thermal induced stress - high temperature operation over long periods of time
HOW TO AVOID MURA
Although we can not guarantee the complete eradication of Mura every time, in general the appearance of Mura can be minimized by these methods:
• Lower the backlight brightness
• Use a screen saver
• Reduce the ambient temperature around the unit
29
BDL4652EL
7.
Cleaning and Troubleshooting
7.1.
Cleaning
Caution When Using the Display
• Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the display is usually very hot due to the high
temperature of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too
close. Placing any object near the top of the display could also result in heat related damage to the object as well as the display itself.
• Be sure to disconnect all cables before moving the display. Moving the display with its cables attached may damage the cables and thus cause fire
or electric shock.
• Disconnect the power plug from the wall outlet as a safety precaution before carrying out any type of cleaning or maintenance procedure.
Front Panel Cleaning Instructions
• The front of the display has been specially treated. Wipe the surface gently using only a cleaning cloth or a soft, lint-free cloth.
• If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent solution. Wring the cloth to remove excess liquid. Wipe the surface of
the display to remove dirt. Then use a dry cloth of the same type to dry.
• Do not scratch or hit the surface of the panel with fingers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners.
Cabinet Cleaning Instructions
• If the cabinet becomes dirty, wipe the cabinet with a soft, dry cloth.
• If the cabinet is extremely dirty, soak a lint-free cloth in a mild detergent solution. Wring the cloth to remove as much moisture as possible. Wipe
the cabinet. Use another dry cloth to wipe over until the surface is dry.
• Do not allow any water or detergent to come into contact with the surface of the display. If water or moisture gets inside the unit, operating
problems, electrical and shock hazards may result.
• Do not scratch or hit the cabinet with fingers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners on the cabinet.
• Do not place anything made from rubber or PVC near the cabinet for any extended periods of time.
30
BDL4652EL
7.2.
Troubleshooting
Symptom
Possible Cause
Remedy
No picture is displayed
1. The power cord is disconnected.
1. Plug in the power cord.
2. The main power switch on the back of the
display is not switched on.
2. Make sure the power switch is switched on.
3. The selected input has no connection.
3. Connect a signal connection to the display.
4. The display is in standby mode.
Interference displayed on the display or audible
noise is heard
Caused by surrounding electrical appliances or
fluorescent lights.
Move the display to another location to see is the
interference is reduced.
Color is abnormal
The signal cable is not connected properly.
Make sure that the signal cable is attached firmly
to the back of the display.
Picture is distorted with abnormal patterns
1. The signal cable is not connected properly.
1. Make sure that the signal cable is attached
firmly.
2. The input signal is beyond the capabilities of
the display.
Display image doesn’t fill up the full size of the
screen
1. The zoom mode is not set correctly.
2. Scan Mode may be set incorrectly to
underscan.
2. Check the video signal source to see if it
is beyond the range of the display. Please
verify its specifications with this display’s
specification section.
Use the Zoom mode or Custom zoom function
in the Screen menu to fine tune display geometry
and time frequency parameter.
3. If the image exceeds the screen size, Scan
Mode may need to be set to Underscan.
Can hear sound, but no picture
Improperly connected source signal cable.
Make sure that both video inputs and sound
inputs are correctly connected.
Can see picture but no sound is heard
1. Improperly connected source signal cable.
1. Make sure that both video inputs and sound
inputs are correctly connected.
2. Volume is turned all the way down.
3. [MUTE] is turned on.
4. No external speaker connected.
2. Press [VOL UP] or [VOL DOWN] button to
hear sound.
3. Switch MUTE off by using the [MUTE]
button.
4. Connect external speakers and adjust the
volume to a suitable level.
Some picture elements do not light up
Some pixels of the display may not turn on.
This display is manufactured using an extremely
high level of precision technology: however,
sometimes some pixels of the display may not
display. This is not a malfunction.
After-Images can still be seen on the display
after the display is powered off. (Examples
of still pictures include logos, video games,
computer images, and images displayed in 4:3
normal mode)
A still picture is displayed for an over extended
period of time
Do not allow a still image to be displayed for
an extended period of time as this can cause a
permanent after-image to remain on the display.
31
BDL4652EL
8.
Technical Specifications
Display:
Item
Specifications
Screen Size (Active Area)
46” LCD (116.8 cm)
Aspect Ratio
16:9
Number of pixels
1920 (H) x 1080 (V)
Pixel pitch
0.17675 (H) x 0.53025 (V) [mm]
Displayable colors
1073.7M colors
Brightness (typical)
500 cd/m2
Contrast ratio (typical)
4000:1
Viewing angle
178 degrees
In/Out Terminals:
Item
Speaker Output
Specifications
Internal Speakers
10W (L) + 10W (R) [RMS]/8Ω
External Speakers
1 Way 1 Speaker System
82 dB/W/M/160 Hz ~ 13 KHz
Audio Output
RCA Jack x 2
0.5V [rms] (Normal) / 2 Channel (L+R)
Audio Input
RCA Jack x 2
0.5V [rms] (Normal) / 2 Channel (L+R)
3.5 mm Stereo x 1
RS232C
D-Sub Jack x 2 (9 pin)
TXD + RXD (1:1)
RJ-45
RJ-45 Jack x 1 (8 pin)
10/100 LAN Port
HDMI Input
HDMI Jack x 1 (Type A) (18 pin)
Digital RGB: TMDS (Video + Audio)
MAX:
Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
Audio - 48 KHz/ 2 Channel (L+R)
Supports LPCM only
DVI-D Input
DVI-D jack
Digital RGB: TMDS (Video)
VGA Input
D-Sub Jack x 1 (15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
DVI-I (DVI-D & VGA)
Output
DVI-I Jack x 1 (29 pin)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
Digital RGB: TMDS (Video)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
Component Input
BNC Jack x 3
Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω)
MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
Video Input
BNC x 1 (Share with
Component_Y)
Composite 1V [p-p] (75Ω)
Displayport Input
Displayport Jack x 1
(20 pin)
Digital RGB: TMDS (Video + Audio)
MAX:
Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel (L+R)
Supports LPCM only
General:
Item
Specifications
Power Supply
AC 100 ~ 240V, 50 ~ 60Hz
Power Consumption (Max.)
245W
Power consumption (Typ.)
92W
Power Consumption (Standby & Off)
<0.5W (RS232 in active)
Dimensions (With Stand) [W x H x D]
1052.7 x 662.7 x 400 mm
Dimensions (Without Stand) [W x H x D]
1052.7 x 607.3 x 69 mm
Weight (With Stand)
24.3 Kg
32
BDL4652EL
Weight (Without Stand)
22.0 Kg
Gross Weight (Without Stand)
28.8 Kg
Environmental Condition:
Item
Temperature
Humidity
Altitude
Specifications
Operational
0 ~ 40°C
Storage
-20 ~ 60°C
Operational
20 ~ 80% RH (No condensation)
Storage
5 ~ 95% RH (No condensation)
Operational
0 ~ 3,000 m
Storage / Shipment
0 ~ 9,000 m
Internal Speaker:
Item
Specifications
Type
1 Way 1 Speaker
Input
10 W (RMS)
Impedance
8Ω
Output Sound Pressure
82 dB/W/M
Frequency Response
160 Hz ~ 13 KHz
33
2013 © Koninklijke Philips N.V. All rights reserved.
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used under license from
Koninklijke Philips N.V.
Specifications are subject to change without notice.