Philips Signage Solutions D-Line Display BDL4235DL

BDL4235DL
www.philips.com/welcome
User Manual (English)
BDL4235DL
Safety Instructions
IMPORTANT: Always activate a moving screen saver program when
you leave your display unattended. Always activate a periodic screen
refresh application if the unit will display unchanging static content.
Uninterrupted display of still or static images over an extended period
may cause “burn in”, also known as “after-imaging” or “ghost imaging”, on
your screen. This is a well-known phenomenon in LCD panel technology.
In most cases, the “burned in” or “after-imaging” or “ghost imaging” will
disappear gradually over a period of time after the power has been
switched off.
Safety precautions and maintenance
WARNING: Use of controls, adjustments or
procedures other than those specified in this
documentation may result in exposure to shock,
electrical hazards and/or mechanical hazards.
WARNING: Severe “burn-in” or “after-image” or “ghost image”
symptoms will not disappear and cannot be repaired. This is also not
covered under the terms of your warranty.
Read and follow these instructions when connecting
and using your display:
Service:
Operation:
• The casing cover should be opened only by qualified service
personnel.
• Keep the display out of direct sunlight and away from stoves or any
other heat sources.
• If there is any need for repair or integration, please contact your
local service center.
• Remove any object that could fall into ventilation holes or prevent
proper cooling of the display’s electronics.
• Do not leave your display under direct sunlight.
• Do not block the ventilation holes on the cabinet.
If your display does not operate normally,
having followed the instructions set out in this
document, please contact a technician or your
local service center..
• When positioning the display, make sure the power plug and outlet
are easily accessible.
• When turning off the display by detaching the power cord, wait 6
seconds before re-attaching the power cord for normal operation.
• Ensure the use of an approved power cord provided by Philips at
all times. If your power cord is missing, please contact your local
service center.
• Do not subject the display to severe vibration or high impact
conditions during operation.
• Do not knock or drop the display during operation or
transportation.
Maintenance:
• To protect your display from possible damage, do not put excessive
pressure on the LCD panel. When moving your display, grasp the
frame to lift; do not lift the display by placing your hand or fingers
on the LCD panel.
• Unplug the display if you are not going to use it for an extensive
period of time.
• Unplug the display if you need to clean it with a slightly damp cloth.
The screen may be wiped with a dry cloth when the power is off.
However, never use organic solvent, such as, alcohol, or ammoniabased liquids to clean your display.
• To avoid the risk of shock or permanent damage to the set, do
not expose the display to dust, rain, water or an excessively moist
environment.
• If your display becomes wet, wipe it with dry cloth as soon as
possible.
• If a foreign substance or water gets in your display, turn the power
off immediately and disconnect the power cord. Then remove the
foreign substance or water, and send the unit to the maintenance
center.
• Do not store or use the display in locations exposed to heat, direct
sunlight or extreme cold.
• In order to maintain the best performance of your display and
ensure a longer lifetime, we strongly recommend using the display in
a location that falls within the following temperature and humidity
ranges.
-- Temperature: 0-40°C 32-104°F
-- Humidity: 20-80% RH
ii
BDL4235DL
Regulatory Information
Read and follow these instructions
when connecting and using your Public
Information Display:
CE Declaration of Conformity
• Unplug the display if you are not going to use it for an extensive
period of time.
We declare under our responsibility that the product is in conformity
with the following standards:
• Unplug the display if you need to clean it with a slightly damp cloth.
The screen many be wiped with a dry cloth when the power is off.
However, never use alcohol, solvents or ammonia-based liquids.
• EN60950-1:2006+A11:2009+A1:2010+A12:2011 (Safety
requirement of Information Technology Equipment).
• EN55022:2010 (Radio Disturbance requirement of Information
Technology Equipment).
• Consult a service technician if the display does not operate normally
when you have followed the instructions in this manual.
• The casing cover should be opened only by qualified service
personnel.
• EN55024:2010 (Immunity requirement of Information Technology
Equipment).
• Keep the display out of direct sunlight and away from stoves or any
other heat sources.
• EN61000-3-2:2006 +A1:2009+A2:2009 (Limits for Harmonic
Current Emission).
• Remove any object that could fall into the vents or prevent proper
cooling of the display’s electronics.
• EN61000-3-3:2008 (Limitation of Voltage Fluctuation and Flicker)
• EN 50581:2012 (Technical documentation for the assessment of
electrical and electronic products with respect to the restriction of
hazardous substances)
• Do not block the ventilation holes on the cabinet.
• Keep the display dry. To avoid electric shock, do not expose it to
rain or excessive moisture.
following provisions of directives applicable.
• If turning off the display by detaching the power cable, wait for 6
seconds before re-attaching the power cable for normal operation.
• 2006/95/EC (Low Voltage Directive).
• To avoid the risk of shock or permanent damage to the set do not
expose the display to rain or excessive moisture.
• 2004/108/EC (EMC Directive).
• When positioning the display, make sure the power plug and outlet
are easily accessible.
• 2009/125/EC (ErP, Energy-related Product Directive, EC No.
1275/2008 and 642/2009 Implementing)
• IMPORTANT: Always activate a screen saver program during your
application. If a still image in high contrast remains on the screen for
an extended period of time, it may leave an ‘after-image’ or ‘ghost
image’ on the front of the screen. This is a well-known phenomenon
that is caused by the shortcomings inherent in LCD technology. In
most cases the afterimage will disappear gradually over a period
of time after the power has been switched off. Be aware that the
after-image symptom cannot be repaired and is not covered under
warranty.
• 2011/65/EU (RoHS Directive) and is produced by a manufacturing
organization on ISO9000 level.
iii
BDL4235DL
Federal Communications Commission (FCC)
Notice (U.S. Only)
Polish Center for Testing and Certification
Notice
The equipment should draw power from a socket with an attached
protection circuit (a three-prong socket). All equipment that works
together (computer, display, printer, and so on) should have the same
power supply source.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions manual, may cause harmful interference to
radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference
in which case the user will be required to correct the
interference at his own expense.
The phasing conductor of the room’s electrical installation should have
a reserve short-circuit protection device in the form of a fuse with a
nominal value no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must
be removed from the power supply socket, which should be located
near the equipment and easily accessible.
A protection mark “B” confirms that the equipment is in compliance
with the protection usage requirements of standards PN-93/T-42107
and PN-89/E-06251.
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
Use only an RF shielded cable that was supplied with the display when
connecting this display to a computer device.
To prevent damage which may result in fire or shock hazard, do not
expose this appliance to rain or excessive moisture.
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS
OF THE CANADIAN INTERFERENCE- CAUSING EQUIPMENT
REGULATIONS.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Electric, Magnetic and Electronmagnetic
Fields (“EMF”)
1. We manufacture and sell many products targeted at consumers,
which, like any electronic apparatus, in general have the ability to
emit and receive electromagnetic signals.
2. One of our leading Business Principles is to take all necessary health
and safety measures for our products, to comply with all applicable
legal requirements and to stay well within the EMF standards
applicable at the time of producing the products.
3. We are committed to develop, produce and market products that
cause no adverse health effects.
4. We confirm that if its products are handled properly for their
intended use, they are safe to use according to scientific evidence
available today.
5. We play an active role in the development of international EMF and
safety standards, enabling us to anticipate further developments in
standardization for early integration in its products.
iv
BDL4235DL
Information for U.K. only
China RoHS
WARNING – THIS APPLIANCE MUST BE EARTHED.
中国电子信息产品污染控制标识要求
Important:
本产品有毒有害物质或元素的名称及含量标识表:
(B)
有毒有害物质或元素
铅
汞
镉
六价铬 多溴联苯 多溴二苯醚
(Pb) (Hg) (Cd) (Cr 6+)
(PBBs)
(PBDEs)
塑料外框
O
O
O
O
O
O
后壳
O
O
O
O
O
O
X
O
O
O
O
LCD CCFL X
面板 LED
X
O
O
O
O
O
电源基板
X
O
O
O
O
O
主基板
X
O
O
O
O
O
按键基板
X
O
O
O
O
O
底座
O
O
O
O
O
O
电源线
X
O
O
O
O
O
其他线材
X
O
O
O
O
O
遥控器
X
O
O
O
O
O
*:电路板组件包括印刷电路板及其构成的零部件,如电阻、电容、
集成电路、连接器等。
○:表示该有害物质在该部件所有均质材料中的含量均在SJ/
T11363-2006《电子信息产品中有毒有害物质的限量要求》规定的
限量要求以下。
零部件名称
(A)
This apparatus is supplied with an approved moulded 13A plug. To
change a fuse in this type of plug proceed as follows:
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved
type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut
off and an appropriate 3-pin plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 5A. If a plug
without a fuse is used, the fuse at the distribution board should not be
greater than 5A.
×:表示该有害物质至少在该部件的某一均质材料中的含量超出
SJ/T11363-2006《电子信息产品中有毒有害物质的限量要求》规定
的限量要求;
NOTE: T
he severed plug must be destroyed to avoid a possible shock
hazard should it be inserted into a 13A socket elsewhere.
备注:以上“×”的部件,部分含有有害物质超过是由于目前行业
技术水平所限,暂时无法实现替代或减量化。
How to connect a plug
10
环保使用期限
在产品本体上标示的该标志表示环境保护使用期限为 10 年。
电子信息产品的环境保护使用期限是指电子信息产品中所含的有
毒有害物质或元素不会向外部泄漏或出现突然变异,并且电子信
息产品的用户在使用该电子信息产品时也不会对环境造成严重污
染或对人体、财产带来严重损害的期限。
在环境保护期限中,请按照使用说明书使用本产品。
The wires in the mains lead are coloured in accordance with the
following code:
本环境保护使用不覆盖易损件:电池。
BLUE – “NEUTRAL” (“N”)
《废弃电子产品回收处理管理条例》提示性说明
BROWN – “LIVE” (“L”)
为了更好地关爱及保护地球,当用户不再需要此产品或产品寿命
终止时,请遵守国家废弃电器电子产品回收处理相关法律规定,
将其交给当地具有国家认可的回收处理资质的厂商进行回收处
理。
GREEN & YELLOW – “EARTH” (“E”)
1. The GREEN & YELLOW wire must be connected to the terminal in
the plug which is marked with the letter “E” or by the Earth symbol
or coloured GREEN or GREEN & YELLOW.
2. The BLUE wire must be connected to the terminal which is marked
with the letter “N” or coloured BLACK.
3. The BROWN wire must be connected to the terminal which
marked with the letter “L” or coloured RED.
Before replacing the plug cover, make certain that the cord grip is
clamped over the sheath of the lead – not simply over the three wires.
v
BDL4235DL
中国能源效率标识
End-of-Life Disposal
根据中国大陆《能源效率标识管理办法》,本显示器
符合以下要求
Your new Public Information Display contains materials that can be
recycled and reused. Specialized companies can recycle your product to
increase the amount of reusable materials and to minimize the amount
to be disposed of.
能源效率 (cd/W)
能效等级
能效标准
>1.05
1级
GB 21520-2008
Please find out about the local regulations on how to dispose of your
old display from your local Philips dealer.
(For customers in Canada and U.S.A.)
详细有关信息请查阅中国能效标识网: http://www.
energylabel.gov.cn/
This product may contain lead and/or mercury. Dispose of in accordance
to local-state and federal regulations. For additional information on
recycling contact www.eia.org (Consumer Education Initiative)
North Europe (Nordic Countries)
Information
Placering/Ventilation
Waste Electrical and Electronie EquipmentWEEE
VARNING:
Attention users in European Union private households
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG
ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING
PÅPLATS.
This marking on the product or on its packaging
illustrates that, under European Directive 2012/19/
EU governing used electrical and electronic appliances,
this product may not be disposed of with normal
household waste. You are responsible for disposal of
this equipment through a designated waste electrical
and electronic equipment collection. To determine
the locations for dropping off such waste electrical
and electronic, contact your local government office,
the waste disposal organization that serves your
household or the store at which you purchased the
product.
Placering/Ventilation
ADVARSEL:
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG
STIKKONTAKT ER NEMT TILGÆNGELIGE.
Paikka/Ilmankierto
Attention users in United States:
VAROITUS:
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN
TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
Please dispose of according to all Local, State and Federal Laws. For the
disposal or recycling information, contact: www.mygreenelectronics.com
or www.eiae.org.
Plassering/Ventilasjon
End of Life Directives-Recycling
Your new Public Information Display contains several
materials that can be recycled for new users.
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT
KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
Please dispose of according to all Local, State, and
Federal laws.
As an ENERGY STAR Partner, we have determined
that this product meets the ENERGY STAR guidelines
for energy efficiency.
vi
BDL4235DL
Table Of Contents
1. Unpacking and Installation...................................... 1
1.1. Unpacking......................................................................1
1.2. Package Contents......................................................1
1.3. Installation Notes.......................................................1
1.4. Mounting on a Wall..................................................2
1.5. Mounting in Portrait Position..............................3
1.5.1. How to use the logo guider for
portrait position.........................................3
1.5.2. How to remove the logo......................3
4.6.1. Playing music files...................................12
4.6.2. Playing movie files..................................13
4.6.3. Playing photo files..................................13
5. Change your settings.............................................14
5.1. Quick Picture and Sound...................................14
5.2. Settings.........................................................................14
5.2.1. Picture menu.............................................14
5.2.2. Sound menu..............................................15
5.2.3. General settings menu.........................16
5.3. Network Settings....................................................16
2. Parts and Functions.................................................. 4
2.1. Control Panel...............................................................4
2.2. Input/Output Terminals..........................................5
2.3. Remote Control.........................................................6
2.3.1. General functions......................................6
2.3.2. Inserting batteries in the remote
control.............................................................7
2.3.3. Handling the remote control..............7
2.3.4. Operating range of the remote
control.............................................................7
6. Input mode...............................................................17
7. Pixel Defect Policy..................................................18
7.1. Pixels and Sub-pixels.............................................18
7.2. Types of Pixel Defects + Dot Definition.. 18
7.3. Bright Dot Defects................................................18
7.4. Dark Dot Defects..................................................19
7.5. Proximity of Pixel Defects.................................19
7.6. Pixel Defect Tolerances.......................................19
7.7. MURA...........................................................................19
3.Connection................................................................ 8
3.1. Connecting External Equipments.....................8
3.2. Connecting Multiple Displays.............................9
3.2.1. RS232C control connection
(optional)........................................................9
3.2.2. IR connection (optional).......................9
3.3. IR Pass-through Connection (optional)........9
3.4. Wire-connecting to Network (optional)....10
8.
Cleaning and Troubleshooting..............................20
8.1. Cleaning.......................................................................20
8.2. Troubleshooting.......................................................21
9. Technical Specifications.........................................22
4.Operation.................................................................11
4.1. Watch the Connected Video Source..........11
4.2. Change Picture Format.......................................11
4.3. Select your Preferred Picture Settings........11
4.4. Select your Preferred Sound Settings.........11
4.5. Play Multimedia Files.............................................11
4.5.1. Play Multimedia files via Local Area
Network......................................................11
4.5.2. Play files from display............................11
4.5.3. Play multimedia files from USB
device............................................................12
4.6. Play options................................................................12
vii
BDL4235DL
1.
Unpacking and Installation
1.1.
Unpacking
• This product is packed in a carton, together with the standard accessories.
• Any other optional accessories will be packed separately.
• Due to the size and weight of this display it is recommended for two people to move it.
• After opening the carton, ensure that the contents are complete and in good condition.
1.2.
Package Contents
Please verify that you received the following items with your package content:
• LCD display
• CD ROM
• Remote control with AAA batteries
• Power cord (1.8 m)
CD ROM
• VGA cable (1.8 m)
LCD Display
• RS232 cable (1.8 m)
LCD-Display / Pantalla LCD / Écran LCD / Display LCD /
Wyświetlacz LCD / ЖК-монитор / LCD Ekran / 监视器 / 監視器
BDL4235DL
• Quick start guide
• Logo guider
• Power switch cover
Remote Control
and AAA Batteries
* The supplied power cord varies depending on destination.
Kurzanleitung / Guía rápida / Guide de démarrage rapide / Guida rapida /
Instrukcja szybkiego uruchomienia / Краткое руководство по запуску /
Hızlı başlangiç kılavuzu / 快速入门指南 / 快速入門指南
Installation / Installation / Instalación / Installation / Installazione / Instalacja /
Установка / Kurulum / 安装 / 安裝
Connect / Verbindungsfähigkeit / Conectividad / Connectivité / Connettività /
Połączenia / Подключение / Bağlantı / 连接性 / 連接性
Register your product and get support at
www.philips.com/welcome
• Screw for Power switch cover (M3,
8mm x 1)
Quick Start Guide
Power Cord
Logo Guider
RS232 Cable
VGA Cable
Power switch cover
and screw (M3x8) x1
NOTES:
• For all other regions, apply a power cord that conforms to the AC voltage of the power socket and has been approved by and complies with the
safety regulations of the particular country.
• Keep the package box and packing material for shipping the display.
1.3.
Installation Notes
• Due to the high power consumption, always use the plug exclusively designed for this product. If an extended line is required, please consult your
service agent.
• The product should be installed on a flat surface to avoid tipping. The distance between the back of the product and the wall should be maintained
for proper ventilation. Avoid installing the product in the kitchen, bathroom or any other places with high humidity so as not to shorten the service life
of the electronic components.
• The product can normally operate only under 3000 m in altitude. In installations at altitudes above 3000 m, some abnormalities may be experienced.
1
BDL4235DL
1.4.
Mounting on a Wall
To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially available). We recommend using a mounting interface
that complies with UL1678 standard in North America.
400
Protective Sheet
200
Table
1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath the screen surface so as not to scratch the
screen face.
2. Ensure you have all accessories for mounting this display (wall mount, ceiling mount, table stand, etc).
3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the equipment
or injury to the user or installer. Product warranty does not cover damage caused by improper installation.
4. For the wall-mounting kit, use M6 mounting screws (20 mm long plus the thickness of the mounting bracket) and tighten them securely.
Caution:
To prevent the display from falling:
• For wall or ceiling installation, we recommend installing the display with metal brackets which are commercially available. For detailed installation
instructions, refer to the guide received with the respective bracket.
• To lessen the probability of injury and damage resulting from fall of the display in case of earthquake or other natural disaster, be sure to consult the
bracket manufacturer for installation location.
Ventilation Requirements for enclosure locating
To allow heat to disperse, leave space between surrounding objects as shown in the diagram below.
100 mm
100 mm
100 mm
100 mm
2
BDL4235DL
1.5.
Mounting in Portrait Position
This display can be installed in portrait position.
1. Remove the table stand, if attached.
2. Rotate 90 degrees clockwise. The “
” logo should be on the LEFT side when facing the display.
90
90
1.5.1. How to use the logo guider for portrait position
1. Put the guider on the lower-left corner of the front bezel of the display.
Fold down both of its edges.
1
2
3
1
2
3
2. Peel off the protective film at the back of the “
” logo sticker.
Hold and press the guider with your left hand. Put the “
” logo
sticker with its adhesive side down into the logo hole with your right
hand, and press to make it stick tightly onto the front bezel.
3. Remove the guider.
1.5.2. How to remove the logo
1. Prepare a piece of paper with a cutting area of logo as a protector to
prevent the front bezel from scratching.
2. Using a knife, carefully remove the logo sticker with the paper placing
beneath.
3. Tear off the logo sticker.
NOTE:
hen installing the display on a wall, please consult a professional technician for proper installation. We accept no liability for installations not
W
performed by a professional technician.
3
BDL4235DL
2.
Parts and Functions
2.1.
Control Panel
9
1
1
[
MUTE
INPUT
2
3
4
] button
9
Press to switch the display on or off.
2
[MUTE] button
[
] button
[ ] button
[ ] button
Press to decrease the adjustment while OSD menu is on, or to
decrease the audio output level while OSD menu is off.
6
[ ] button
Press to move the highlight bar up to adjust the selected item while
OSD menu is on.
7
[ ] button
Press to move the highlight bar down to adjust the selected item
while OSD menu is on.
8
[
7
8
Remote control sensor and power status indicator
-- Lights off when the main power of this display is turned off
Press to increase the adjustment while OSD menu is on, or to
increase the audio output level while OSD menu is off.
5
6
-- Lights red when this display is in standby mode
Press to select input source.
4
5
• Receives command signals from the remote control.
-- Lights green when this display is turned on
Switch the audio mute ON/OFF.
3
MENU
] button
Press to access the OSD menu.
4
BDL4235DL
2.2.
Input/Output Terminals
12
11
10
9
L
R
L
OUT
15
14
13
R
IN
OUT
IN
16
1
1
2
3
AC IN
11 SPDIF
MAIN POWER SWITCH
12 IR
AC power input.
2
DVI IN
RJ-45
14 RS232C
16 USB
COMPONENT IN (RCA)
AUDIO IN (RCA)
Audio input from external AV device.
AUDIO OUT (RCA)
Audio signal output to connect your external AV device.
10 AUDIO
IR IN (3.5 mm)
OUT /
15
RS232C IN (2.5 mm)
PORT
Connect your USB storage device.
VGA IN (D-Sub)
Component YPbPr video source input.
9
13
RS232C network output/input for the loop-through function.
VGA video input.
8
OUT /
• To remotely control your A/V device via this display, refer to
page 9 for IR Pass Through connection.
control center.
7
OUT
• This display’s remote control sensor will stop working if the jack
[IR IN] is connected.
LAN control function for the use of remote control signal from
6
7
NOTES:
HDMI IN
DVI-D video input.
5
6
IR signal output/input for the loop-through function.
HDMI video/audio input.
4
5
Digital audio signal output to connect your external AV device.
Main power on/off switch.
3
4
8
IN (3.5mm)
Audio input from your PC.
5
BDL4235DL
2.3.
Remote Control
7
2.3.1. General functions
8
1
9
2
10 3
14
11 4
5
12 15
8
14 16
15 9
16 10
11
12
10
.
13
2
POWER button
Switch this display on or off.
PLAY buttons
Control playback of media files.
3
4
5
6
BACK button
Return to the previous menu page or exit from the previous
function.
VOLUME button
Adjust volume.
MUTE button
Press to turn the mute function on/off.
Select tasks or options.
COLOR buttons
buttons
Enter text for network setting.
7
ADJUST button
Access currently available options, picture and sound menus.
13 NUMERIC
6
1
button
Confirm an entry or selection.
SOURCE button
Select input source. Press [ ] or [ ] button to select from USB,
Network, HDMI, DVI, YPbPr, AV, or VGA. Press [
] button
to confirm and exit.
HOME button
Access the OSD menu.
LIST
No function.
NAVIGATION buttons
Navigate through menus and select items.
6
FORMAT button
Change picture format.
INFO button
Display information about current activity.
OPTIONS
Access currently available options, picture and sound menus.
BDL4235DL
2.3.2. Inserting batteries in the remote control
The remote control is powered by two 1.5V AAA batteries.
To install or replace batteries:
1. Press and then slide the cover to open it.
2. Align the batteries according to the (+) and (–) indications inside the
battery compartment.
3. Replace the cover.
Caution:
The incorrect use of batteries can result in leaks or bursting. Be sure to follow these instructions:
• Place “AAA” batteries matching the (+) and (–) signs on each battery to the (+) and (–) signs of the battery compartment.
• Do not mix battery types.
• Do not combine new batteries with used ones. It causes shorter life or leakage of batteries.
• Remove the dead batteries immediately to prevent them from liquid leaking in the battery compartment. Don’t touch exposed battery acid, as it can
damage your skin.
NOTE: If you do not intend to use the remote control for a long period, remove the batteries.
2.3.3. Handling the remote control
• Do not subject to strong shock.
• Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry immediately.
• Avoid exposure to heat and steam.
• Other than to install the batteries, do not open the remote control.
2.3.4. Operating range of the remote control
Point the front of the remote control toward this display’s remote control sensor when
pressing a button.
Use the remote control within a distance of less than 10m/33ft from this display’s sensor,
and a horizontal and vertical angle of less than 30 degrees.
NOTE: The remote control may not function properly when the remote control sensor
on this display is under direct sunlight or strong illumination, or when there is an
obstacle in the path of signal transmission.
30
7
30
BDL4235DL
3.
Connection
NOTE: The peripherals and cables shown are for example purposes only.
3.1.
Connecting External Equipments
USB
PC
AUDIO OUT
DVD / VCR / VCD
HDMI OUT
R
L
R
L
Y
HDMI IN
8
DVI IN
RJ-45
VGA IN
Pb
Pr
COMPONENT IN
DVI OUT
VGA OUT
IN
COMPONENT OUT (YPbPr)
OUT
RS232C
STEREO AMPLIFIER
IN
AUDIO IN
PC LINE
AUDIO OUT
IN SPDIF OUT
IR
AC IN
AUDIO OUT
AUDIO IN
USB
USB
BDL4235DL
3.2.
Connecting Multiple Displays
3.2.1. RS232C control connection (optional)
DISPLAY 1
DISPLAY 2
[RS-232C]
PC
[RS232C IN]
[RS232C OUT]
[RS232C IN]
[RS232C OUT]
3.2.2. IR connection (optional)
DISPLAY 1
External
IR Receiver
[IR IN]
DISPLAY 2
[IR OUT]
[IR IN]
NOTE: This display’s remote control sensor will stop working if the [IR IN] is connected.
3.3.
IR Pass-through Connection (optional)
DISPLAY
[IR OUT]
DVD / VCR / VCD
[IR IN]
(DVD / VCR / VCD)
Remote Control
(BDL4235EL)
9
[IR OUT]
BDL4235DL
3.4.
Wire-connecting to Network (optional)
If you connect this display to a home network, you can play photos, music and videos from your computer. See Play multimedia files (Page 11) for more
detail.
INTERNET
[RJ-45]
ROUTER
PC
To setup the network:
1. Switch on the router and switch on its DHCP setting.
2. Connect the router to this display with an Ethernet cable.
3. Press
button on the remote control, then select {Setup}.
4. Select {Connect to network}, then press
button.
5. Follow the on-screen instructions to install the network.
6. Wait for this display to find the network connection.
7. If you are prompted, agree to the “End User Licence Agreement”.
NOTE: Connecting with a shielded CAT-5 Ethernet cable to comply with the EMC directive.
10
[RJ-45]
BDL4235DL
4.
Operation
• {News}: Ideal settings for spoken audio, such as the news.
NOTE: The control button described in this section is mainly on the
remote control unless specified otherwise.
4.5.
4.1.
• Your computer connected through your home network.
You can play videos, photos, and music on your display from:
Watch the Connected Video Source
• A USB device connected to this display.
See page 8 for external equipments connection.
1. Press
2. Press
4.2.
button.
or
button to select a device, then press
Play Multimedia Files
4.5.1. Play Multimedia files via Local Area
Network
button.
To play files from computer, you will need:
Change Picture Format
• A wired home network, connected with a Universal Plug and Play
(uPnP) router.
You can change the picture format to suit the video source. Each video
source has its available picture formats.
The available picture formats depend on the video source:
• Optional: A LAN cable that connects your display to your home
network.
1. Press
• A media server running on your computer.
button.
2. Press or button to select a picture format, then press
• Appropriate settings on your computer firewall to allow you to run
the media server.
button.
• {Auto zoom}: Enlarge the picture to fill the screen.
Recommended for minimal screen distortion but not for HD or
PC.
Set up the network
1. Connect your display and the computer to the same home network.
See page 10 for connecting your display to a network.
• {Movie expand 16:9}: Scale 4:3 format to 16:9. Not
recommended for HD or PC.
2. Switch on your computer and the router.
• {Wide screen}: Shows widescreen format content unstretched.
Not recommended for HD or PC.
NOTE: If the apparatus does not return to DLNA mode due to
external electrical disturbances (e.g. electrostatic discharge), user
intervention is required.
• {Unscaled}: Provide maximum detail for PC. Only available
when PC mode is selected in the {Picture} menu.
Single Display Setup
• {4:3}: Display the classic 4:3 format.
4.3.
Select your Preferred Picture Settings
1. While this display is playing video source, press
button.
2. Press
or
button to select
, then press
button.
or
[RJ-45]

3. Press or button to select an option, then press
ROUTER
[RJ-45]
PC
button:
• {Personal}: Apply your personalised picture settings.
Multiple Displays Setup
• {Vivid}: Rich and dynamic settings, ideal for daytime viewing.
• {Natural}: Natural picture settings.
• {Standard}: Default settings that suit most environments and
types of video.
or
[RJ-45]
• {Movie}: Ideal settings for movies.
ROUTER
[RJ-45]
[RJ-45]
PC
• {Photo}: Ideal settings for photos.
• {Energy saving}: Settings that conserve the most energy.
4.4.
4.5.2. Play files from display.
Select your Preferred Sound Settings
Set up media sharing
1. While this display is playing video source, press
button.
2. Press
or
button to select
, then press
button.
1. Install a media server on your computer to share media files. These
are some media servers:

3. Press or button to select an option, then press
• For PC: Windows Media Player 11 (or higher) or TVersity
• For Mac: Twonky
button:
2. Switch on media sharing on your computer using the media server.
For more information on how to set up the media server, refer to
the website of the media server.
• {Personal}: Apply your personalised sound settings.
• {Original}: Settings that suit most environments and types of
audio.
• {Movie}: Ideal settings for movies.
• {Music}: Ideal settings for listening to music.
• {Game}: Ideal settings for games.
11
BDL4235DL
Supported file system:
Play files
1. Press
• FAT32
button.
2. Select [Browse network], then press
button.
3. Select a file from the content browser, then press
start playing.
Supported file format:
button to
• Music: MP3, WMA, M4A, AAC, AC3
• Movie: AVI, MP4, MOV, RM/RMVB
4. Press the Play buttons on the remote control to control playing.
• Photo: JPEG, BMP, GIF
Tips:
Caution:
• Select the top bar to filter your files by type.
• The manufacturer is not responsible if the USB device is not
supported, nor is it responsible for damage to or loss of data in the
device.
• Select [Sort] to arrange the files by album name, artist, or other
fields.
• To clear the list of offline media servers, press
button, then select [Clear offline servers] and press
• Do not overload the USB port. If you connect a USB storage
device that consumes more than 500mA power, make sure that it is
connected to its own external power supply.
button.
4.5.3. Play multimedia files from USB device
4.6.
This display can play music, movie, or photo files from your USB device.
1. Connect your USB device to the USB port on this display.
4.6.1. Playing music files
USB
in the top bar.
OUT
IN
USB
1. Select Music
2. Select one music track, then press
button.
PC LINE
IN SPDIF OUT
1. Funky music
05:05
AUDIO IN
AUDIO OUT
IR
IN
RS232C
Play options
2. Press
button, select USB, then press
Info
button.
Play All
Sort
USB device
Help
Options
• To play all the tracks in a folder, select one music file, then select
{Play All}.
3. The connected USB device is detected automatically for all its
playable files, which will be automatically sorted into 3 types:
,
, and
.
• To skip to the next or previous track, press
button.
or
• To pause the track, press
button. Press
button again to
resume playback.
or
button.
• To skip backward or forward 10 seconds, press
• To search backward or forward, press G or J button,
press repeatedly to toggle between different speeds.
• To stop the music, press H button.
Music options
While you play music, press
button to select an option:
• {Repeat}: Select {Repeat} to play a track or an album repeatedly, or
select {Play once} to play a track once.
Help
4. Press the
BACK button to go up to the top layer in the screen.
Press
button to select the file type. Press
button to enter
its play list.
5. Select the file you want. Press
button, then press
• {Media Server}: When you play content from a media server, you
can select another media server.
• {Shuffle On} / {Shuffle Off}: Enable or disable random play of tracks.
button to start playing.
6. Follow the on-screen instruction to control the play option.
7. Press the PLAY buttons (H F G I J) to control playing.
12
BDL4235DL
NOTE: To view information about a song (for example, title, artist or
duration), select the song, then press
button. To hide
the information, press
button again.
NOTE: To view information about a video (for example, played position,
duration, title, or date), select the video, then press
button. To hide the information, press
button again.
4.6.2. Playing movie files
4.6.3. Playing photo files
1. Select Movie
1. Select Photo
in the top bar.
2. Select a video, then press
Info
2. Select a photo thumbnail, then press
button.
The Movie
11:22:33
88.88MB
2013-05-05
The Movie
11:22:33
88.88MB
2013-05-05
The Movie
11:22:33
88.88MB
2013-05-05
The Movie
11:22:33
88.88MB
2013-05-05
Play All
USB device
• To skip to the next or previous video, press
button.
button.
The Movie
11:22:33
88.88MB
2013-05-05
Help
Info
Options
• To play all the videos in a folder, select one video file, then select
{Play All}.
Play All
Sort
USB device
Help
Options
Start a slideshow
If there are multiple photos in a folder, select a photo, then select {Play
All}.
or
button, and
• To skip to the previous or next photo, press
then press
button.
or
• To pause the video, press
button. Press
button again to
resume playback.
or
button.
• To skip backward or forward 10 seconds, press
• To stop the slideshow, press H button.
Slideshow options
• To search backward or forward, press G or J button,
press repeatedly to toggle between different speeds.
While you play a slideshow, press
button to select an option:
• To stop the video, press H button.
button, then press
• {Shuffle Off} / {Shuffle On}: Enable or disable random display of
pictures in the slideshow.
Movie options
While playing video, press
button to select an option:
in the top bar.
button, then press
• {Repeat}: Select {Repeat} to watch a slideshow repeatedly or {Play
once} to watch once.
• {Subtitles}: Select the available subtitle settings.
• {Slideshow Time}: Select the displaying time for each photo in the
slideshow.
• {Subtitle Language}: Select the language for subtitles if available.
• {Character Set}: Select the correct character set for the subtitles.
• {Slideshow Transitions}: Select the transition from one photo to the
next.
• {Audio Language}: Select an audio language.
• {Media Server}: When you play content from a media server, you
can select another media server.
• {Repeat}: Select {Repeat} to play the video file repeatedly or {Play
once} to play the video file once.
• {Media server}: When you play content from a media server, you
can select another media server.
• {Shuffle On} / {Shuffle Off}: Enable or disable random play of video
files.
• {DivX(R) VOD}: Display the DivX registration and deregistration
codes for this display.
13
BDL4235DL
5.
Change your settings
Using this display’s control buttons:
Using the remote control:
MUTE
1. Press
2. Press
INPUT
MENU
button to display the OSD menu.
, or
button to select {Setup}. Press
button to enter.
1. Press
button to display the OSD menu.
2. Press[
value.
Source
Setup
][
] [ ] or [ ] button to select menu item or adjust its
3. Press
submenu.
button to confirm menu selection and enter its
4. Press
button to exit the OSD menu.
5.1.
Quick Picture and Sound
You can select picture and sound settings with the help of the settings
assistant, which demonstrates the effect of your chosen setting
immediately.
button to select {Quick picture and sound},
3. Press , , , or
{Settings}, {Connect to network}, or {Network settings}. Press
button to enter.
1. Press
button to display the OSD menu.
2. Select {Setup}. Press
button.
3. Select {Quick picture and sound}. Press
4. Select {Continue}, then press
button.
button
5. Follow the on-screen instructions to choose your preferred settings.
Quick picture and
sound
Connect to network
Settings
Network settings
5.2.
5.2.1. Picture menu
button to select its menu item or to adjust its
4. Press , , , or
value. Press
button to confirm.
5. Press
6. Press
Settings
button to go back to the previous menu layer.
Picture
Picture style
Sound
Restore style
General settings
Backlight contrast
Colour
button to exit the OSD menu.
Sharpness
Noise reduction
MPEG artifact reducti...
Digital Crystal Clear
Advanced
Game or computer
Foramat and edges
Picture style
Select a predefined picture setting.
14
BDL4235DL
5.2.2. Sound menu
Restore style
Restore the last-selected predefined picture setting.
Backlight contrast
Picture
Sound style
Adjust the brightness of this display’s backlight.
Sound
Restore style
Colour
General settings
Bass
Treble
Adjust the colour saturation of the picture.
Surround mode
Sharpness
Audio out
Adjust the sharpness of the picture.
Advanced
Noise reduction
Select the amount of noise reduction for the picture.
MPEG artifact reduction
Smoothen transitions and haziness in the digital picture.
Digital Crystal Clear
Sound style
Fine-tune each pixel to match surrounding pixels and produce a brilliant,
high-definition image.
Access predefined sound settings.
• {Advanced sharpness}: Enable superior sharpness, especially on
lines and contours in the picture
Restore style
Restore the last-selected predefined sound setting.
• {Dynamic contrast}: Dynamically enhance the details in the
dark, medium and light areas of the picture.
Bass
• {Dynamic backlight}: Select a backlight level to optimise dynamic
power consumption and picture contrast.
Adjust the bass level of the speaker and headphones.
• {Colour enhancement}: Dynamically enhance the vividness and
details of colours.
Adjust the treble level of the speaker and headphones.
Treble
Surround mode
Advanced
Select a surround sound mode to enhance your audio experience.
Access advanced settings such as gamma, tint settings and video contrast
settings.
Audio out
• {Gamma}: Adjust the non-linear setting for picture luminance
and contrast.
Adjust audio output volume.
• {Tint}: Change the colour balance.
Access advanced settings to enhance your audio experience.
Advanced
• {Custom tint}: Customise colour balance setting. Only available
if {Tint}  {Custom} is selected.
• {Video contrast}: Adjust video contrast.
• {Auto volume leveling}: Enable the reduction of sudden volume
changes.
• {Speaker settings}: Turn on or off the internal speakers.
• {Brightness}: Adjust screen brightness.
• {Clear sound}: Enhance sound quality.
• {Audio out format}: Select the type of audio output through
the digital audio output connector.
Game or computer
When viewing content from a connected game console, select {Game}
to apply game settings. When a computer is connected through HDMI,
select {Computer}.
• {Audio out leveling]: Set the output level for stereo audio.
Select {Less} for a certain amount of loss in intensity or signal
strength. Select {More} for no loss in intensity or signal strength.
Make sure that {Format and edges}  {Picture format}  {Unscaled}
is selected so as to view maximum detail.
• {Audio out delay}: Automatically sync the image on this display
to the audio from a connected home theatre.
Format and edges
• {Audio out offset}: Adjust the setting for audio output delay.
Available if {Audio out delay} is switched on.
Access advanced settings to control the displaying format of the picture.
• {Picture format}: Change the picture format.
• {Screen edges}: Change the picture size.
• {Picture shift}: If available, move the position of the picture.
15
BDL4235DL
5.2.3. General settings menu
Picture
Menu language
Sound
Monitor id
General settings
Eco mode
• {Lock but volume}: Disable all the button function except the
button.
• {Lock but power}: Disable all the button function except the
button.
NOTE: To disable the lock function from [Local KB lock] or [RC
lock] item, press buttons
1998
on the remote
control.
Auto search
Clock
USB scheduling
Factory settings
Sleep timer
Reset all your customized settings to the factory defaults.
Auto switch off
5.3.
Local KB lock
RC lock
Factory settings
Network Settings
View network settings
Network settings
Static IP Configuration
Menu language
Digital Media Renderer ..
Select language used for OSD menus.
Monitor id
Set the ID number for controlling this display via the RS232C
connection. Each display must have a unique ID number when multiple
sets of this display are connected.
Eco mode
Set this display to reduce the power consumption automatically.
Auto search
Choose to let this display detect and display available signal sources
automatically.
View network settings
View connected network status.
Clock
Network settings
Adjust clock settings.
Select how this display should assign addresses to the network
resources.
USB scheduling
This function allows you to program up to 3 different scheduled time
intervals for this display to activate, and auto play USB media file of your
setting.
Static IP Configuration
Assign {IP address}, {Netmask}, {Gateway}, {DNS1}, and {DNS2} for
this display.
After changing the {Clock} option in the {General settings} menu, you
need to set this {USB scheduling} again.
Digital Media Renderer - DMR
Receive multimedia files from Smart Phones or Tablets connected to
your network.
Sleep timer
Switch off this display after a specified time.
Auto switch off
Set the time for this display to be switched off after a period of no
activity. Press any key on the remote control to disable this function.
Local KB lock
Choose to enable or disable the keyboard (control buttons) function of
this display.
• {Unlock}: Enable the keyboard function.
• {Lock all}: Lock all keyboard function.
• {Lock but volume}: Disable all the keyboard function except the
and
button.
• {Lock but power}: Disable all the keyboard function except the
button.
RC lock
Choose to enable or disable the button function of the remote control.
• {Unlock}: Enable the button function.
• {Lock all}: Lock all button function.
16
BDL4235DL
6.
Input mode
PC Resolution:
Standard
Resolution
Active Resolution
H Pixels
Refresh Rate
Pixel Rate
480
60 Hz
25.175 MHz
480
72 Hz
31.5 MHz
480
75 Hz
31.5 MHz
400
70 Hz
33.75 MHz
600
60 Hz
40 MHz
600
75 Hz
49.5 MHz
768
60 Hz
65 MHz
768
75 Hz
78.75 MHz
V Lines
Aspect Ratio
Stand for Mode
4:3
Video Graphic Array
16:9
Wide Video Graphic Array
4:3
Super VGA
4:3
Extended Graphic Array
VGA
640
WVGA
720
SVGA
800
XGA
1024
WXGA
1280
768
60 Hz
79.5 MHz
5:3
Wide XGA
WXGA
1280
800
60 Hz
79.5 MHz
16:10
Wide XGA
SXGA
1280
1024
60 Hz
108 MHz
5:4
Super XGA
WXGA
1360
768
60 Hz
85.5 MHz
16:9
Wide XGA
UXGA
1600
1200
60 Hz
162 MHz
4:3
Ultra XGA
HD1080
1920
1080
60 Hz
148.5 MHz
16:9
HD1080
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
29.97 Hz
13.5 MHz
59.94 Hz
27 MHz
4:3
Modified NTSC Standard
25 Hz
13.5 MHz
50 Hz
27 MHz
4:3
Modified PAL Standard
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
74.25 MHz
16:9
Normally DVB Mode
74.25 MHz
16:9
Normally ATSC Mode
148.5 MHz
16:9
Normally ATSC Mode
SDTV Resolution:
Standard
Resolution
480i
480p
576i
576p
Active Resolution
H Pixels
V Lines
720
480
720
480
HDTV Resolution:
Active Resolution
Standard
Resolution
H Pixels
V Lines
720p
1280
720
1080i
1920
1080
1080p
1920
1080
50 Hz
60 Hz
25 Hz
30 Hz
50 Hz
60 Hz
• The PC text quality is optimum in HD 1080 mode (1920 × 1080, 60 Hz).
• Your PC display screen might appear different depending on the manufacturer (and your particular version of Windows).
• Check your PC instruction book for information about connecting your PC to a display.
• If a vertical and horizontal frequency-select mode exists, select 60 Hz (vertical) and 31.5 KHz (horizontal). In some cases, abnormal signals (such as
stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the [
] button to enter the
video mode. Also, make sure that the PC is connected.
• When horizontal synchronous signals seem irregular in RGB mode, check PC power saving mode or cable connections.
• This display settings table complies to the IBM/VESA standards, and based on the analog input.
• The DVI support mode is regarded as same to the PC support mode.
• The best timing for the vertical frequency to each mode is 60 Hz.
17
BDL4235DL
7.
Pixel Defect Policy
We strive to deliver the highest quality products and use some of the industry’s most advanced manufacturing processes whilst practicing stringent quality
control. However, pixel or sub-pixel defects on the PDP / TFT panels used in Plasma- & LCD- displays are sometimes unavoidable. No manufacturer can
guarantee that all panels will be free from pixel defects, but Philips guarantees that any Plasma- & LCD- displays with an unacceptable number of defects
will be repaired during the warranty period in line with your local guarantee conditions.
This notice explains the different types of pixel defects and defines the acceptable defect level for the LCD screen. In order to qualify for repair under
warranty, the number of pixel defects must exceed a certain level as shown in the reference table. If the LCD screen is within specification a warranty
exchange / claim back will be refused. Additionally, because some types or combinations of pixel defects are more noticeable than others, Philips sets even
higher quality standards for those.
7.1.
Pixels and Sub-pixels
A pixel, or picture element, is composed of three sub-pixels in the primary colors of red, green and
blue. Many pixels together form an image. When all sub-pixels of a pixel are lit, the three colored
sub-pixels together appear as a single white pixel. When all are dark, the three colored sub-pixels
together appear as a single black pixel. Other combinations of lit and dark sub-pixels appear as
single pixels of other colors.
subpixel
pixel
7.2.
Types of Pixel Defects + Dot Definition
Pixel and sub-pixel defects appear on the screen in different ways. There are three categories of pixel defects and several types of sub-pixel defects within
each category.
Dot definition = What is a defective “Dot”? :
One or more defective, adjacent sub-pixel are defined as one “dot”. The no. of defective sub-pixels are not relevant to define a defective dot. This means
that a defective dot can consist of one, two or three defective sub-pixels which can be dark or lit.
R G B
One dot = One Pixel; consists of three sub-pixels of Red, Green, and Blue.
7.3.
Bright Dot Defects
Bright dot defects appear as pixels or sub-pixels that are always lit or “on”. These are the examples of bright dot defects:
One lit red, green or blue sub pixel
Two adjacent lit sub pixels:
Red + Blue = Purple
Red + Green = Yellow
Green + Blue = Cyan (Light Blue)
18
Three adjacent lit sub pixels (one white pixel)
BDL4235DL
7.4.
Dark Dot Defects
Black dot defects appear as pixels or sub-pixels that are always dark or “off ”. These are the examples of black dot defects:
One dark dot
7.5.
Two adjacent dark dots = 1 pair of dark dots
Two dark dots, specifications defines the
minimum distance between dark dots
Proximity of Pixel Defects
Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also specifies tolerances for the
proximity of pixel defects. In the table below you can find specifications about:
• Allowed amount of adjacent dark dots = (adjacent dark dots =1 pair of dark dots)
• Minimum distance between dark dots
• Total no. of all defective dots
7.6.
Pixel Defect Tolerances
In order to qualify for repair due to pixel defects during the warranty period, a PDP / TFT panel in a Philips Plasma / LCD- display must have pixel or subpixel defects exceeding the tolerances listed in the following table.
BRIGHT DOT EFFECT
ACCEPTABLE LEVEL
1 lit sub pixel
2
BLACK DOT EFFECT
ACCEPTABLE LEVEL
1 dark sub pixel
10
TOTAL DOT DEFECTS OF ALL TYPES
12
NOTE:
* 1 or 2 adjacent sub pixel defects = 1 dot defect
7.7.
MURA
Dark spots or patches may occasionally appear on some liquid crystal display (LCD) panels. This is known within the industry as Mura, which is a Japanese
term for “unevenness.” It is used to describe an irregular pattern or area in which uneven screen uniformity appears under certain conditions. Mura is a
result of the deterioration of the liquid crystal alignment layer and is most commonly caused by long-term operation under high ambient temperatures. It
is an industry- wide phenomenon and Mura is not repairable. It is also not covered by our warranty terms.
Mura has been around since the introduction of LCD technology and with screens getting bigger and in operation 24/7, many displays are running in low
light conditions. This all adds to the possibility of Mura affecting displays.
HOW TO SPOT MURA
There are many symptoms of Mura and also multiple causes. Several of these are listed below:
• Impurities or foreign particles in the crystal matrix
• Uneven distribution of LCD matrix during manufacturing
• Non-uniform luminance distribution of the backlight
• Panel assembly induced stress
• Flaws within the LCD cells
• Thermal induced stress – high temperature operation over long periods of time
HOW TO AVOID MURA
Although we can not guarantee the complete eradication of Mura every time, in general the appearance of Mura can be minimized by these methods:
• Lower the backlight brightness
• Use a screen saver
• Reduce the ambient temperature around the unit
19
BDL4235DL
8.
Cleaning and Troubleshooting
8.1.
Cleaning
Caution When Using the Display
• Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the display is usually very hot due to the high
temperature of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too
close. Placing any object near the top of the display could also result in heat related damage to the object as well as the display itself.
• Be sure to disconnect all cables before moving the display. Moving the display with its cables attached may damage the cables and thus cause fire
or electric shock.
• Disconnect the power plug from the wall outlet as a safety precaution before carrying out any type of cleaning or maintenance procedure.
Front Panel Cleaning Instructions
• The front of the display has been specially treated. Wipe the surface gently using only a cleaning cloth or a soft, lint-free cloth.
• If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent solution. Wring the cloth to remove excess liquid. Wipe the surface of
the display to remove dirt. Then use a dry cloth of the same type to dry.
• Do not scratch or hit the surface of the panel with fingers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners.
Cabinet Cleaning Instructions
• If the cabinet becomes dirty, wipe the cabinet with a soft, dry cloth.
• If the cabinet is extremely dirty, soak a lint-free cloth in a mild detergent solution. Wring the cloth to remove as much moisture as possible. Wipe
the cabinet. Use another dry cloth to wipe over until the surface is dry.
• Do not allow any water or detergent to come into contact with the surface of the display. If water or moisture gets inside the unit, operating
problems, electrical and shock hazards may result.
• Do not scratch or hit the cabinet with fingers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners on the cabinet.
• Do not place anything made from rubber or PVC near the cabinet for any extended periods of time.
20
BDL4235DL
8.2.
Troubleshooting
Symptom
Possible Cause
Remedy
No picture is displayed
1. The power cord is disconnected.
1. Plug in the power cord.
2. The main power switch on the back of the
display is not switched on.
2. Make sure the power switch is switched on.
3. The selected input has no connection.
3. Connect a signal connection to the display.
4. The display is in standby mode.
Interference displayed on the display or audible
noise is heard
Caused by surrounding electrical appliances or
fluorescent lights.
Move the display to another location to see is the
interference is reduced.
Color is abnormal
The signal cable is not connected properly.
Make sure that the signal cable is attached firmly
to the back of the display.
Picture is distorted with abnormal patterns
1. The signal cable is not connected properly.
1. Make sure that the signal cable is attached
firmly.
2. The input signal is beyond the capabilities of
the display.
2. Check the video signal source to see if it
is beyond the range of the display. Please
verify its specifications with this display’s
specification section.
Display image doesn’t fill up the full size of the
screen
The zoom mode is not correctly set.
Use the Zoom mode or Custom zoom function
in the Screen menu to fine tune display geometry
and time frequency parameter.
Can hear sound, but no picture
Improperly connected source signal cable.
Make sure that both video inputs and sound
inputs are correctly connected.
Can see picture but no sound is heard
1. Improperly connected source signal cable.
1. Make sure that both video inputs and sound
inputs are correctly connected.
2. Volume is turned all the way down.
3. [MUTE] is turned on.
2. Press [
4. No external speaker connected.
3. Switch MUTE off by using the
button.
] or [
] button to hear sound.
[
]
4. Connect external speakers and adjust the
volume to a suitable level.
Some picture elements do not light up
Some pixels of the display may not turn on.
This display is manufactured using an extremely
high level of precision technology: however,
sometimes some pixels of the display may not
display. This is not a malfunction.
After-Images can still be seen on the display
after the display is powered off. (Examples
of still pictures include logos, video games,
computer images, and images displayed in 4:3
normal mode)
A still picture is displayed for an over extended
period of time
Do not allow a still image to be displayed for
an extended period of time as this can cause a
permanent after-image to remain on the display.
21
BDL4235DL
9.
Technical Specifications
Display:
Item
Specifications
Screen Size (Active Area)
42”(viewable 41.92”/ 106.48 cm)
Aspect Ratio
16:9
Number of Pixels
1920 (H) × 1080 (V)
Pixel Pitch
0.4833 (H) × 0.4833 (V) [mm]
Displayable Colors
16.7 Million colors
Brightness
400 cd/m²
Contrast Ratio (Typical)
1000:1
Viewing Angle
178 degrees
In/Out Terminals:
Item
Specifications
Speaker Output
Internal Speakers
7W (L) + 7W (R) [RMS]/8Ω, 1 Way 1 Speaker System
Audio Output
RCA Jack × 2
0.5V [rms] (Normal) / 2 Channel (L+R)
Audio Input
3.5 mm Stereo × 1
0.5V [rms] (Normal) / 2 Channel (L+R)
82 dB/W/M/160 Hz ~ 13 KHz
RCA Jack × 2
RS232C Input/Output
2.5 mm × 2
TXD + RXD (1:1)
LAN
RJ-45 Jack × 1 (8 pin)
10/100 LAN Port
HDMI Input
HDMI Jack × 1 (Type A) (19 pin)
Digital RGB: TMDS (Video + Audio)
MAX:
Video: 720p, 1080p, 1920 × 1080/60 Hz (WUXGA)
Audio: 48 KHz / 2 Channel (L+R)
Supports LPCM only
DVI-D Input
DVI-D jack
Digital RGB: TMDS (Video)
VGA Input
D-Sub Jack × 1 (15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V: TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
Component Input
RCA Jack × 3
SPDIF Output
SPDIF Port
Serial digital audio output when input is HDMI
IR Input/Output
3.5 mm × 2
IR pass through or IR daisy chain
USB Input
USB × 1 (Type A)
USB 2.0, for flash disk
MAX: 720p, 1080p, 1920 × 1080/60 Hz (WUXGA)
Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω)
MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
General:
Item
Specifications
Power Input
100-240V
Power Consumption (Max.)
106 W
Power Consumption (Typical)
80 W
Power Consumption (EPA6.0)
51.5 W
Power Consumption (Standby & Off)
< 0.5W
Dimensions [W × H × D]
991.6 × 584.0 × 113.9 mm
Weight
15.21 Kg
Gross Weight
21.1 Kg
50-60Hz, 2.5A Max
Environmental Condition:
Item
Temperature
Humidity
Altitude
Specifications
Operational
5 ~ 40°C
Storage
-20 ~ 60°C
Operational
20 ~ 80% RH (No condensation)
Storage
10 ~ 90% RH (No condensation)
Operational
0 ~ 3,000 m
Storage/Shipment
0 ~ 9,000 m
22
© 2013 Koninklijke Philips N.V. All rights reserved.
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips N.V. and are used under license from
Koninklijke Philips N.V.
Specifications are subject to change without notice.