0:
ENGLISH
MODEL
XL-UH06H
MICRO COMPONENT SYSTEM
OPERATION MANUAL
XL-UH06H Micro Component System consisting of XL-UH06H (main unit) and CP-UH06H (speaker system).
Accessory
Volume control
Please confirm that only the following accessory is
included.
The sound level at a given volume setting depends on
speaker efficiency, location and various other factors. It is
advisable to avoid exposure to high volume levels. Do not
turn the volume on to full at switch on. Listen to music at
moderate levels.
Remote control x 1
(92L34900016601)
Special note
Supply of this product does not convey a license nor imply any right to distribute content created with this product in
revenue-generating broadcast systems (terrestrial, satellite, cable and/or other distribution channels), revenue generating
streaming applications (via Internet, intranets and/or other networks), other revenue-generating content distribution
systems (pay-audio or audio-on-demand applications and the like) or on revenue-generating physical media (compact
discs, digital versatile discs, semiconductor chips, hard drives, memory cards and the like). An independent license for
such use is required. For details, please visit http://mp3licensing.com
*=92L875000166024D*|
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.
92L87500016602
13E R MW 1
Special notes
WARNINGS:
● When the ON/STAND-BY button is set at STAND-BY
position, mains voltage is still present inside the unit.
When the ON/STAND-BY button is set at STAND-BY
position, the unit may be brought into operation by
remote control.
● This unit contains no user serviceable parts. Never
remove covers unless qualified to do so. This unit contains
dangerous voltages, always remove mains plug from the
socket before any service operation and when not in use
for a long period.
● To prevent fire or shock hazard, do not expose this
appliance to dripping or splashing. No objects filled with
liquids, such as vases, shall be placed on the apparatus.
● Do not turn the volume on to full at switch on and listen to
music at moderate levels.
● The voltage used must be the same as that specified on
this unit. Using this product with a higher voltage other
than that which is specified is dangerous and may result
in a fire or other type of accident causing damage. SHARP
will not be held responsible for any damage resulting from
use of this unit with a voltage other than that which is
specified.
Information on Proper Disposal
CAUTION:
● This product is classified as a CLASS 1 LASER product.
● This product contains a low power laser device. To ensure
continued safety, do not remove any cover or attempt to
gain access to the inside of the product.Refer all servicing
to qualified personnel.
Note:
Audio-visual material may consist of copyrighted works which
must not be recorded without the authority of the owner of the
copyright. Please refer to the relevant laws in your country.
Dichiarazione di conformità
La società SHARP ELECTRONICS dichiara che il prodotto
XL-UH06H Micro Sitema è costruito in conformità alle
prescrizioni del D.M.no 548 del 28/8/95, pubblicato sulla G.U.no
301 del 28/12/95 ed in particolare è conforme a quanto indicato
nell’art. 2, comma 1 dello stesso decreto.
DENNA APPARAT ÄR ANSLUTEN TILL 230 V
VÄXELSTRÖM NÄR STICKPROPPEN ÄR
INSKJUTEN I VÄGGUTTAGET. FÖR ATT
FULLSTÄNDIGT KOPPLA IFRÅN APPARATEN,
V.G. DRAG UT STICKPROPPEN.
Attention:
Your
product is
marked with
this symbol.
It means
that used
electrical
and
electronic
products
should not
be mixed
with general
household
waste.
There is a
separate
collection
system
for these
products.
A. Information on Disposal for Users (private
households)
1. In the European Union
Attention: If you want to dispose of this equipment,
please do not use the ordinary dustbin!
Used electrical and electronic equipment must
be treated separately and in accordance with
legislation that requires proper treatment, recovery
and recycling of used electrical and electronic
equipment.
Following the implementation by member states,
private households within the EU states may return
their used electrical and electronic equipment to
designated collection facilities free of charge*.
In some countries* your local retailer may also take
back your old product free of charge if you purchase
a similar new one.
*) Please contact your local authority for further
details.
If your used electrical or electronic equipment
has batteries or accumulators, please dispose of
these separately beforehand according to local
requirements.
By disposing of this product correctly you will help
ensure that the waste undergoes the necessary
treatment, recovery and recycling and thus prevent
potential negative effects on the environment and
human health which could otherwise arise due to
inappropriate waste handling.
2. In other Countries outside the EU
If you wish to discard this product, please contact
your local authorities and ask for the correct method
of disposal.
For Switzerland: Used electrical or electronic
equipment can be returned free of charge to the
dealer, even if you don’t purchase a new product.
Further collection facilities are listed on the
homepage of www.swico.ch or www.sens.ch.
B. Information on Disposal for Business Users
1. In the European Union
If the product is used for business purposes and
you want to discard it:
Please contact your SHARP dealer who will inform
you about the take-back of the product. You might
be charged for the costs arising from take-back and
recycling. Small products (and small amounts) might
be taken back by your local collection facilities.
For Spain: Please contact the established collection
system or your local authority for take-back of your
used products.
2. In other Countries outside the EU
If you wish to discard of this product, please contact
your local authorities and ask for the correct method
of disposal.
Information on Battery Disposal
The battery supplied with this product contains
traces of Lead.
For EU: The crossed-out wheeled bin implies that
used batteries should not be put to the general
household waste! There is a separate collection
system for used batteries, to allow proper treatment
and recycling in accordance with legislation. Please
contact your local authority for details on the
collection and recycling schemes.
For Switzerland: The used battery is to be returned
to the selling point.
For other non-EU countries: Please contact your
local authority for correct method of disposal of the
used battery.
E-
System connections
■
Precautions
● Please ensure that the equipment is positioned in a
well ventilated area and ensure that there is at least
10 cm (4”) of free space along the sides, top and back
of the equipment.
10 cm (4”)
10 cm (4”)
10 cm (4”)
● The ventilation should not be impeded by covering the
ventilation openings with items, such as newspapers,
tablecloths, curtains, etc.
● No naked flame sources, such as lighted candles,
should be placed on the apparatus.
● Attention should be drawn to the environmental
aspects of battery disposal.
● This unit should only be used within the range of 5°C
- 35°C (41°F - 95°F).
● The apparatus is designed for use in moderate
climates.
10 cm (4”)
■
● Use the unit on a firm, level surface free from
vibration.
● Place the speakers at least 30 cm (12”) away from any
CRT TV to avoid colour variations across the TV screen.
If the variations persist, move the speakers further away
from the TV. LCD TV is not prone to such variation.
● Keep the unit away from direct sunlight, strong magnetic
fields, excessive dust, humidity and electronic/electrical
equipment (home computers, facsimiles, etc.) which
generate electrical noise.
● Do not place anything on top of the unit.
● Do not expose the unit to moisture, to temperatures
higher than 60°C (140°F) or to extremely low
temperatures.
● If your system does not work properly, disconnect the
AC power lead from the wall socket. Plug the AC power
lead back in, and then turn on your system.
● In case of an electrical storm, unplug the unit for
safety.
● Hold the AC power plug by the head when removing it
from the wall socket, as pulling the lead can damage
internal wires.
● The AC power plug is used as a disconnect device
and shall always remain readily operable.
● Do not remove the outer cover, as this may result
in electric shock. Refer internal service to your
local SHARP service facility.
Speaker connection
● Fully insert the speaker wires into the speaker
terminals.
● Use speakers with an impedance of 4 ohms or more,
as lower impedance speakers can damage the unit.
● Do not make a mistake when connecting the right and
left speakers. The right speaker is the one on the right
side when you face the unit.
● Do not allow any objects to fall into or to be placed in
the bass reflex ducts.
● Do not stand or sit on the speakers. You may be
injured.
E-
System connections (continued)
Make sure to unplug the AC power lead before making any connections.
FM aerial
The spec label (*)
10 21W
The spec label illustration
may be different from the
actual label used.
(*) Label is located at the
bottom of the unit.
Wall socket
(AC 220 - 240 V ~ 50/60 Hz)
Right speaker
Left speaker
Remote control - battery installation
Note:
Before using remote control, please remove plastic shield
at battery holder.
1 While pushing the locking tab towards the centre
of the remote control, slide out the battery holder.
Remote
control
Plastic
shield
Battery holder
Back of remote
control
Locking tab
2 Remove the old battery from the battery holder,
insert the new battery and then slide the battery
holder back into the remote control.
Battery holder
Polarity
(+) symbol
Battery type
Locking tab
Positive (+)
side up
Precautions for battery use:
Remove the battery if the unit will not be used for long
periods of time. This will prevent potential damage due
to battery leakage.
Caution:
● Do not use rechargeable battery (nickel-cadmium
battery, etc.).
● Danger of explosion if battery is incorrectly replaced.
● Replace only with the same or equivalent type.
● Batteries (battery pack or battery installed) shall not
be exposed to excessive heat such as sunshine, fire
or the like.
● Installing the battery incorrectly may cause the unit to
malfunction.
Notes concerning use:
● Replace the battery if the operating distance is
reduced or if the operation becomes erratic. Purchase
“CR 2025”, coin lithium battery.
● Periodically clean the transmitter on the remote control
and the sensor on the unit with a soft cloth.
● Exposing the sensor on the unit to strong light may
interfere with operation. Change the lighting or the
direction of the unit if this occurs.
● Keep the remote control away from moisture, heat,
shock, and vibrations.
E-
General control
■
Auto power off function
The main unit will enter the stand-by mode after 15
minutes of inactivity during:
CD/USB: In the stop or pause mode.
AUDIO IN: No detection of input signal.
■
Muting
The volume is muted temporarily when pressing the MUTE
button on the remote control. Press again to restore the
volume.
■
Function (on main unit only)
When the FUNCTION button on main unit is pressed, the
current function will change to different mode. Press the
FUNCTION button repeatedly to select desired function.
Note:
The backup function will protect the memorised function
mode for a few hours should there be a power failure or
the AC power lead becomes disconnected.
■
Equalizer
Press the EQUALIZER button repeatedly until the desired
sound mode appears.
■
To turn the power on
Function
Main unit
■
Operation
Press to turn the
power on or to
go to stand-by
mode.
Volume auto set-in
Volume control
Press the VOLUME +/– button to increase or decrease
the volume.
■
ROCK
For rock music. (ROCK indicator lights up.)
POPS
For pop music. (POPS indicator lights up.)
VOCAL
Vocals are enhanced. (VOCAL indicator lights up.)
JAZZ
● If you turn off and on the main unit with volume set to
16 or higher, the volume will start at 16.
● If you turn the unit off then on again with the volume
level set to less than 16, it will turn on again at the
level set.
■
No equalisation. (No indicator)
CLASSIC For classical music. (CLASSIC indicator lights up.)
Remote
control
Power on/
off
FLAT
Extra bass control (X-BASS)
When the X-BASS button is pressed, the unit will enter the
extra bass mode which emphasises the bass frequencies
and “X-BASS” indicator will light up. To cancel the extra
bass mode, press the X-BASS button again.
E-
For jazz. (JAZZ indicator lights up.)
Listening to a CD or MP3/WMA disc
Press here
Press here
■
Various disc functions
Function
Play
Main
unit
Remote
control
■
Operation
Press in the stop
mode.
Pause
Press in the
playback mode.
Press the
button to resume
playback from
the paused
point.
Stop
Press in the
playback mode.
Track
up/
down
Press in the
playback or stop
mode. If you
press the button
in the stop
mode, press the
button to
start the desired
track.
Fast
forward/
reverse
Press and hold
down in the
playback mode.
Release the
button to resume
playback.
Disc playback
1 Press the ON/STAND-BY button to turn the power on.
2 Press the CD button on the remote control or
FUNCTION button on the main unit repeatedly to
select CD function.
3 Open the disc compartment.
4 Place the disc on the disc tray, label side up.
Close the disc compartment.
Total number of tracks
on disc.
6 Press the
button to start playback. After the last
track is played, the unit will stop automatically.
● During playback, press DISPLAY button to display the
track number. It will appear for about 2 seconds.
Notes for CD or MP3/WMA discs:
● When the end of the track is reached during fast
forward, the CD operation will be stopped. When
the beginning of the first track is reached during fast
reverse, the unit will enter the playback mode.
E-
Listening to a CD or MP3/WMA disc (continued)
■
Direct track search
■
Random play
By using the Numeric buttons, the desired tracks on the
current disc can be played.
The tracks on the disc can be played in random order
automatically.
Use the Numeric buttons on the remote control to
select the desired track.
To random play all tracks:
Press and hold down PLAY MODE button on the remote
control until RDM indicator appears.
● The Numeric buttons allow you to select up to number
9.
● When selecting number 10 or higher, use the “10+”
button.
To cancel random play:
Press the PLAY MODE button until
disappears.
RDM indicator
A. For example, to
choose 13
1 Press the “10+”
button once.
2 Press the “1” button.
3 Press the “3” button.
Selected track number
B. For example, to choose 130
1
2
3
4
Press the “10+” button twice.
Press the “1” button.
Press the “3” button.
Press the “0” button.
Notes:
● A track number higher than the number of tracks on
the disc cannot be selected.
● During random play, direct search is not possible.
To stop playback:
Press the button on main unit or remote control.
Notes:
● Selecting the repeat function will cancel the random
playback.
● Playback will stop after all the tracks is played
randomly.
● If you press the
or
button during random
play, you can move to the track selected next by the
random operation.
● In random play, the unit will select and play tracks
automatically. (You cannot select the order of the
tracks.)
■ Procedure to play back MP3/WMA disc
with folder mode off
1 Select the CD function, and load an MP3/WMA disc.
After disc is loaded, disc info will be displayed.
2 Select desired file to be played back by pressing the
or
button.
button. Playback will start.
● During playback, press DISPLAY button to display the
folder, then track number. It will appear for about 2
seconds.
Note:
If the track is skipped during playback, it means
“Copyright protected WMA file” or “Not supported
playback file” is selected.
3 Press the
■
Repeat play
Repeat play can play one track, all tracks or a programmed
sequence continuously.
To repeat one track:
Press the PLAY MODE button repeatedly until
indicator appears. Press the
button.
■ Procedure to play back MP3/WMA disc
with folder mode on
To repeat all tracks:
Press the PLAY MODE button repeatedly until
indicator appears. Press the
button.
To repeat all desired tracks:
Perform steps 1 - 6 in “Programmed play” section on
page 7 and then press the PLAY MODE button until
indicator appears.
To cancel repeat play:
Press the PLAY MODE button again until
indicator disappears.
To play back CD-R/RW.
1 Select the CD function, and load an MP3/WMA disc.
Press the FOLDER button and the disc info will be
displayed. (Folder mode on.)
or
Total number of folders
2 Press the PRESET/FOLDER ( or ) button to select
desired playback folder. Folder number and total tracks in
the chosen folder will be displayed interchangeably.
E-
Listening to a CD or MP3/WMA disc (continued)
Folder number
Adding tracks to the programme:
If a programme has been previously stored, the “MEM”
indicator will be displayed. Follow steps 1 - 4 to add
tracks. The new tracks will be stored after the last track of
the previous programme.
Selected track number
■ Programmed play (MP3/WMA with folder
mode on)
3 Select desired file to be played back by pressing the
or
button.
4 Press the
button. Playback will start.
● During playback, press DISPLAY button to display the
Folder, then Track Number. It will appear for about 2
seconds.
■ Programmed play (CD or MP3/WMA with
folder mode off)
You can choose up to 32 selections for playback in the
order you like.
1 While in the stop mode, press the FOLDER button.
(Folder mode on)
2 Press the MEMORY button on the remote control to
enter the programming save mode.
You can choose up to 32 selections for playback in the
order you like.
1 While in the stop mode, press the MEMORY button
on the remote control to enter the programming save
mode.
3 Press the PRESET/FOLDER ( or ) button to select
desired playback folder, then press the
button to select desired track.
or
2 Press the
or
button on the remote control to
select the desired track.
Selected folder number
Selected track number
4� Press the MEMORY button to save the track number.
Selected track number
3 Press the MEMORY button to save the track number.
5� Repeat steps 2 - 3 for other tracks. Up to 32 tracks can
be programmed.
6� Press the
button to start playback.
7� During programmed playback, press button to stop
programmed playback. The total number in memory
will appear.
4 Repeat steps 2 - 3 for other tracks. Up to 32 tracks
can be programmed. If you make a mistake, press the
CLEAR button while the “MEM” indicator is flashing.
Each time the button is pressed, one track will be
cleared, beginning with last track programmed.
button to start playback.
Press the
6 Press the CD button. The total number in memory
will appear.
To cancel the programmed play mode:
While in the stop mode and the “MEM” indicator is lit,
press the CLEAR button on the remote control. The
“MEM” indicator will disappear and all the programmed
contents will be cleared.
Notes:
● When a disc is ejected, the programme is automatically
cancelled.
● If you press the ON/STAND-BY button to enter the
stand-by mode or change the function from CD to
another, the programmed selections will be cleared.
● During the programme operation, random play is not
possible.
E-
Listening to USB mass storage device/MP3 player
The following functions are the same as CD operation:
● Direct search
● Repeat play
● Random play
● Playback
● Programmed play
Note:
If the USB memory device is not connected, “no” will be
shown on the display.
■ To remove USB memory device
1 Press the button to stop playback.
2 Press the button again and wait until display “Un”
stops blinking.
3 Disconnect the USB memory device from the USB
terminal.
Note:
This product is not compatible with MTP and AAC file
systems.
■ To play back USB/MP3 player
1 Press the USB button on the remote control or
Notes:
● SHARP will not be held liable for the loss of data while
the USB memory device is connected to the audio
system.
● This USB memory’s format supports FAT 16 or FAT
32.
● SHARP cannot guarantee that all USB memory
devices will work on this audio system.
● USB cable is not recommended for use in this audio
system to connect to USB memory device. Use of the
USB cable will affect the performance of this audio
system.
FUNCTION button on main unit repeatedly to select
USB function. Connect the USB memory device that
has MP3/WMA format files on the unit. When the USB
memory is connected to the main unit, the device
information will be displayed.
2 Select desired file to be played back by pressing the
or
3 Press the
button.
button. Playback will start.
● During playback, press DISPLAY button to display
the folder, then track number. It will appear for
about 2 seconds.
Note:
To pause playback:
Press the
button.
E-
Listening to USB mass storage device/
MP3 player (continued)
Listening to the radio
Notes:
● This USB memory cannot be operated via USB hub.
● The USB terminal in this unit is not intended for a PC
connection but is used for music streaming with a
USB memory device.
● External HDD-storage cannot be played back via USB
terminal.
● If the data inside the USB memory is large, it may take
longer time for the data to be read.
● The USB port is only intended for direct connection to
a USB memory device without any cable.
● Playback order for MP3 files may differ depending on
the writing software used during file download.
● Bitrate which is supported by MP3 is 32~320 kbps,
WMA is 64~160 kbps.
● Playlists are not supported on this unit.
● The display playback time may not be displayed
correctly when playing back a variable bitrate file.
● Files compressed in MP3 and/or WMA format can be
played back when connected to the USB terminal.
Copyright protected WMA files cannot be played
back.
● This product can play WMA and MP3 files. It will
automatically detect the file type being played. If
unplayable file is played on this product, The file will
be automatically skipped. This will take a few seconds.
If abnormal indications appear on the display due to
the unspecified file, turn off the unit and then turn it
on again.
● This product relates to USB mass storage devices and
MP3 players. It may however face some irregularities
due to various unforeseen reasons from some devices.
Should this happen, turn off the unit and then turn it
on again.
● Maximum total number of MP3/WMA files is 999.
Maximum total number of folders is 99 inclusive of
root directory and folder with non-playable file.
■ Tuning
1 Press the ON/STAND-BY button to turn the power on.
2 Press the TUNER button on the remote control or
FUNCTION button on the main unit repeatedly to
select tuner function.
3 Press the TUNING (
or ) button to tune in to the
desired station.
● Manual tuning:
Press the TUNING ( or ) button repeatedly to
tune in to the desired station.
● Auto tuning:
When the TUNING ( or ) button is pressed
for more than 0.5 seconds, scanning will start
automatically and the tuner will stop at the first
receivable broadcast station.
Notes:
● When radio interference occurs, auto scan tuning may
stop automatically at that point.
● Auto scan tuning will skip weak signal stations.
To receive an FM stereo transmission:
● Press the TUNER button to select stereo mode and
“ST” indicator will be displayed. “
” will appear
when an FM broadcast is in stereo.
● If the FM reception is weak, press the TUNER button to
extinguish the “ST” indicator. The reception changes
to monaural, and the sound becomes clearer.
E-
Listening to the radio (continued)
■ To preset a station
■ To recall a preset station
You can store 40 FM stations in memory and recall them
at the push of a button. (Preset tuning)
Press the PRESET/FOLDER ( or ) button to select the
desired station.
1 Perform steps 2 - 3 in “Tuning”.
2 Press the MEMORY button.
■ To scan the preset stations
3 Within 5 seconds, press the PRESET/FOLDER ( or
) button to select the preset channel number. Store
the stations in memory, in order, starting with preset
channel 1.
4 Press the MEMORY button to store that station in
memory. If the “MEM” and preset number indicators
disappear before the station is memorised, repeat the
operation from step 2.
The stations saved in the memory can be scanned automatically. (Preset memory scan)
1 Press and hold the PRESET/FOLDER ( or ) button.
The preset number will flash and the programmed
stations will be tuned in sequentially, for 5 seconds
each.
2 Press the PRESET/FOLDER ( or ) button again
when the desired station is located.
■ To erase entire preset memory
1 Press and hold the CLEAR button until “CLr”
Repeat steps 1 - 4 to set other stations, or to change
a preset station. When a new station is stored in the
memory, the station previously memorised for that
preset channel number will be erased.
Note:
● During listening to the radio, press DISPLAY button to
display PRESET number.
● The backup function protects the memorised stations
for a few hours should there be a power failure or the
AC power lead become disconnected.
E-10
appears.
Enhancing your system
Troubleshooting chart
The connection lead is not included. Purchase a
commercially available lead as shown below.
Many potential problems can be resolved by the owner
without calling a service technician. If something is wrong
with this product, check the following before calling your
authorized SHARP dealer or service center.
■ General
Symptom
Portable audio
player, etc.
Possible cause
● When a button is ● Set the unit to the power
pressed, the unit
stand-by mode and then
does not respond.
turn it back on.
● If the unit still malfunctions,
reset it. (Refer page 12)
● No
sound
is ● Is the volume level set to
heard.
minimum “L-00”?
● Are the speaker wires
disconnected?
Audio cable
(not supplied)
■ Listening to the playback sounds of
portable audio player, etc.
1 Use a connection lead to connect the portable audio
■ CD player
player etc. to the AUDIO IN socket.
2 Press the ON/STAND-BY button to turn the power
on.
3 Press the AUDIO IN button on the remote control or
FUNCTION button repeatedly on main unit to select
AUDIO IN function.
4 Play the connected equipment. If volume level of the
connected device is too high, sound distortion may
occur. Should this happen, lower the volume of the
connected device. If volume level is too low, increase
the volume of the connected device.
Note:
To prevent noise interference, place the unit away from
the television.
Symptom
Possible cause
● Playback does
not start.
● Playback stops
in the middle or
is not performed
properly.
● Playback sounds
are skipped, or
stopped in the
middle of a track.
● Is the disc loaded upside
down?
● Does the disc satisfy the
standards?
● Is the disc distorted or
scratched?
● Is the unit located near
excessive vibrations?
● Is the disc very dirty?
● Has condensation formed
inside the unit?
■ Remote control
Symptom
Possible cause
● The
remote ● Is the AC power lead of the
control does not
unit plugged in?
operate.
● Is the battery polarity
correct?
● Is the battery dead?
● Is the distance or angle
incorrect?
● Does the remote control
sensor receive strong light?
■ Tuner
Symptom
Possible cause
● The radio makes ● Is the unit placed near the TV
unusual
noises
or computer?
continuously.
● Is the FM aerial placed
properly?
Move the aerial away from
the AC power lead if it is
located nearby.
E-11
Troubleshooting chart (continued)
■ USB
Symptom
■ Factory reset, clearing all memory
1 Press the ON/STAND-BY button to enter the power
Possible cause
stand-by mode.
● Device cannot be ● Is there any MP3/WMA file
detected.
available?
● Is the device properly
connected?
● Is it an MTP device?
● Does the device contain
AAC file only?
2 While pressing down the VOLUME + button, press
button. “rSt” appears.
● Playback does not ● Is it a copyright protected
start.
WMA file?
● Is it a false MP3 file?
● Wrong time display.
● Is Variable Bitrate
being played back?
file
Caution:
This operation will erase all data stored in memory
including tuner preset, and CD program.
■ Condensation
Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation
inside the cabinet (CD pickup, etc.) or on the transmitter
on the remote control. Condensation can cause the unit
to malfunction. If this happens, leave the power on with
no disc in the unit until normal playback is possible (about
1 hour). Wipe off any condensation on the transmitter with
a soft cloth before operating the unit.
■ Before transporting the unit
Remove the disc and USB memory device from the unit.
Then, set the unit to the power stand-by mode. Carrying
the unit with USB memory device left connected or disc
left inside can damage the unit.
■ Care of compact discs
Compact discs are fairly resistant to damage, however
mistracking can occur due to an accumulation of dirt on
the disc surface. Follow the guidelines below for maximum
enjoyment from your CD collection and player.
● Do not write on either side of the disc, particularly the
non-label side from which signals are read. Do not
mark this surface.
● Keep your discs away from direct sunlight, heat, and
excessive moisture.
● Always hold the CDs by the edges. Fingerprints, dirt,
or water on the CDs can cause noise or mistracking.
If a CD is dirty or does not play properly, clean it with
a soft, dry cloth, wiping straight out from the centre,
along the radius.
NO
■ If problem occurs
YES
Correct
When this product is subjected to strong external
interference (mechanical shock, excessive static
electricity, abnormal supply voltage due to lightning, etc.)
or if it is operated incorrectly, it may malfunction.
If such a problem occurs, do the following:
1� Set the unit to the stand-by mode and turn the power
on again.
2� If the unit is not restored in the previous operation,
unplug and plug in the unit again, and then turn the
power on.
Note:
If neither operation above restores the unit, clear all the
memory by resetting it.
Maintenance
■ Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a
diluted soap solution, then with a dry cloth.
Caution:
● Do not use chemicals for cleaning (petrol, paint
thinner, etc.). It may damage the cabinet.
● Do not apply oil to the inside of the unit. It may cause
malfunctions.
E-12
Specifications
As part of our policy of continuous improvement, SHARP
reserves the right to make design and specification
changes for product improvement without prior notice.
The performance specification figures indicated are
nominal values of production units. There may be some
deviations from these values in individual units.
■ USB
USB host
interface
● Complies with USB 1.1 (Full
Speed)/2.0 Mass Storage Class.
● Support Bulk only and CBI
protocol.
Support file
● MPEG 1 Layer 3
● WMA (Non DRM)
Bitrate support
● MP3 (32 ~ 320 kbps)
● WMA (64 ~ 160 kbps)
Other
● Maximum total number of MP3/
WMA files is 999.
● Maximum total number of
folders is 99 INCLUSIVE of root
directory.
File system
support
● Support USB devices with
Microsoft
Windows/DOS/FAT
16/FAT 32.
● 2 kbyte block length for sector.
■ General
Power source
AC 220 - 240 V ~ 50/60 Hz
Power consumption
Power on: 10 W
Power stand-by: 0.4 W (*)
Dimensions
Width: 190 mm (7 - 1/2”)
Height: 115.7 mm (4 - 9/16”)
Depth: 235 mm (9 - 1/4”)
Weight
1.48 kg (3.26 lbs.)
(*) This power consumption value is obtained when the
main unit is in stand-by mode.
■ Amplifier
Output
power
MPO: 6 W (3 W + 3 W) (10% T.H.D.)
RMS: 5 W (2.5 W + 2.5 W) (10% T.H.D.)
RMS: 4 W (2 W + 2 W) (1% T.H.D.)
Output
terminals
Speakers: 4 ohms
■ CD player
■ Tuner
Frequency range
FM: 87.5 - 108 MHz
■ Speaker
Type
1-way type speaker system
8 cm (3”) Full range
Type
Single disc multi-play compact
disc player
Maximum input
power
5W
Signal readout
Non-contact, 3-beam
semiconductor laser pickup
Rated input power
2.5 W
Impedance
4 ohms
D/A converter
Multi bit D/A converter
Dimensions
Frequency
response
20 - 20,000 Hz
Width: 111 mm (4 - 3/8”)
Height: 194 mm (7 - 5/8”)
Depth: 127.5 mm (5 - 1/64”)
Dynamic range
90 dB (1 kHz)
Weight
0.86 kg (1.90 lbs.)/each
E-13