Snow Joe SharperBlade SB601E User manual

Stringless Electric Trimmer/Edger
Model No. SB601E
Form No. SJ-SB601E-880E
OPERATOR’S MANUAL
A Division of Snow Joe, LLC
mCAUTION!
face or dust mask if operation is dusty. Keep body parts
clear of rotating line.
Before using this electric tool, carefully read and observe the
safety rules and instructions listed below. Before starting work,
make sure that you know how to stop the machine in case of
an emergency, The incorrect use of this machine could cause
serious injury. Keep these instructions in a safe place and on
hand so that they can be consulted when required.
5) Use the right tools - Do not use tools for any job except
that for which it is intended.
6) Ground fault circuit interrupter (GFCI) protection should
be provided on the circuit(s) or outlet to be used for the
gardening appliances. Receptacles are available having
built-in GFCI protection and may be used for this measure
for safety.
mCAUTION!
mWARNING: To reduce the risk of electric shock,
The grass trimmer should only be used for cutting lawns and
along the borders of flower beds. Other uses of the trimmer,
not in these instructions, could damage the trimmer or
seriously injure the operator.
7)
Safety Rules
8) Extension cord - Make sure your extension cord is in good
condition. When using an extension cord, be sure to use
one heavy enough to carry the current your product will
draw. An under sized extension cord will cause a drop in
line voltage resulting in loss of power and overheating.
Table 1 shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the
next heavier gauge. The smaller the gauge number, the
heavier the cord. To reduce the risk of disconnection of the
appliance cord from the extension cord during operating:
use only with an extension cord intended for outdoor
use, such as an extension cord of cord type SW-A,
SOW-A, STW-A, STOW-A, SJW-A, SJOW-A, SJTW-A, or
SJTOW-A.
m
WARNING: When using electric gardening tools,
basic safety precautions should always be followed to reduce
the risk of fire, electric shock, and personal injury, including the
following:
Read All Instruction
a) FOR ALL DOUBLE - INSULATED APPLIANCES
Method of securing extension cord
1) Replacement parts - When servicing, use only identical
replacement parts.
Appliance Cord
Cord set
2) Polarized Appliance Connections - To reduce the risk
of electric shock, this appliance has polarized plug (one
blade is wider than the other) and will require the use of a
polarized extension cord. The appliance plug will fit into a
polarized extension cord only one way. If the plug does not
fit fully into the extension cord, reverse the plug. If the plug
still does not fit, obtain a correct polarized extension cord.
This plug will fit into the polarized wall outlet only one way.
If the plug still does not fit fully into wall outlet, reverse
the plug. If the plug still does not fit, contact a qualified
electrician to install proper wall outlet. Do not change the
equipment plug, extension cord receptacle, or extension
cord plug in any way.
(A) Tie cord as shown
b) FOR ALL APPLIANCES
1) Avoid dangerous environment - Don’t use appliances in
damp or wet locations. Don’t use in rain.
2) Children and all visitors should be kept at a distance within
50 feet (15 meters) away from work area; the grass which
is cut and dispersed may contain stones and debris. You
and others can be blinded/injured.
(B) Connect plug and receptacle
Figure 2
3) Dress properly - Always wear suitable clothing when using
the trimmer to prevent head, hand, or feet injuries.
i) Make a knob as shown in figure 2; or
ii) Use one of the plug-receptacle retaining straps or
connectors described in this manual.
4) Wear safety glasses, high boots, (or sturdy shoes and
trousers) for leg protection and work gloves. Always use
© 2011 by Snow Joe, LLC
All rights reserved. Original instructions.
SAVE THESE INSTRUCTIONS
1
mounting, and any other condition that may affect its
operation. A guard or other part that is damaged should
be properly repaired or replaced by an authorized service
center unless indicated elsewhere in this manual.
Table 1 Minimum Gauge for Extension Cords
Volts
Total Length of Cord in Feet
120V
25
50
100
150
240V
50
100
200
300
c) EDGER-TRIMMERS
1) Keep guards in place and in working order.
Ampere Rating
More Than Not more Than AWG
0-6
18
16
16
12
3) Keep hands and feet away from cutting area.
6-10
18
16
14
12
10-12
16
16
14
12
d) ADDITIONAL INSTRUCTIONS FOR LAWN TRIMMER/
EDGE TRIMMER:
12-16
14
12 Not Recommended
2) Keep blade sharp.
mDANGER: Never use steel blades or other devices.
NOTE - Only the applicable parts of the Table need to be
included. For instance, a 120-volt product need not include
the 240-volt heading.
Use of any other accessories or attachments will increase the
risk of injury.
9) Avoid unintentional starting - Don’t carry plugged-in tool
with finger, be sure switch is off when plugging in.
10)Don’t abuse cord - Never carry tool by cord or yank it to
disconnect from receptacle. Keep cord from heat, oil, and
sharp edges.
11)Don’t grasp the exposed cutting blades or cutting edges
when picking up or holding the appliance. (For grass
shears and similar tools only).
mCAUTION!
The blade will continue to rotate after turning the trimmer OFF.
Wait until the blade has completely stopped before making
contact. Do not try to stop the cutting device with your hands.
Be careful of the blade, which can give deep cuts.
12)Don’t force tool - It will do the job better and with less
likelihood of a risk of injury at the rate for which it was
designed.
13)Don’t overreach - Keep proper footing and balance at all
times.
• Only use the type of blade originally provided with the
trimmer.
14)Stay alert - Watch what you are doing. Use common sense.
Do not operate trimmer when you are tired.
• Do not use the trimmer to cut grass which is not in contact
with the ground.
15)Disconnect tool - Turn the trimmer off and disconnect
the plug when: the trimmer is not being used; it is left
unattended; it is being examined because it is not working
correctly; the power supply cable is damaged; the blade
is being removed or changed or when the trimmer is being
moved from one place to another.
• Do not switch the grass trimmer on in enclosed or poorly
ventilated spaces or in the presence of inflammable and/or
explosive substances such as liquids, gas, and powders.
• Only cut during broad daylight or with corresponding
artificial light.
• Do not cross roads or gravel paths with the trimmer still
running.
16)Store idle tools indoors - When not in use, tools should be
stored indoors in dry, and high or docked-up place - out of
reach of children.
• The trimmer must be operated vertical, perpendicular to the
ground.
17)Maintain tools with cares - Keep cutting edge sharp and
clean for best performance and to reduce the risk of
injury. Follow instructions for lubricating and changing
accessories. Inspect trimmer periodically and replace if
damaged, have it repaired by an authorized service facility.
Keep handles dry, clean, free from oil and grease.
• Check regularly that the screws are properly secured.
mCAUTION!
The guard is critical to the safety of the operator and people
near the trimmer. The guard keeps the trimmer in good working
order and must always be in place during operation. Failure to
have the guard in place during operation is dangerous and will
void the warranty.
18)Checked damage parts - Before further use of the trimmer,
a guard or other part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for the alignment of
moving parts, binding of moving parts, breakage of parts,
2
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
Symbol
Description
READ THE OPERATOR’S MANUAL(S) Read, understand and follow all instructions in the manual(s) before attempting to
assemble and operate.
WARNING! Keep out of rain and away from wet areas.
DANGER! Rotating objects may spin off and cause personal injury. Keep people away from hazard area.
WARNING! Always turn the machine OFF and disconnect the
electrical power before conducting inspection, cleaning and
maintenance.
DANGER! Keep electrical extension cable away from tines.
DANGER! Rotating parts may cause serious injury. Allow the blade to completely stop before moving the machine,
inspection, cleaning and maintenance.
SAFETY ALERT
DOUBLE INSULATION
3
Know Your SharperBlade
Electric Trimmer/Edger
A
L
K
J
H
G
F
B
C
D
I
A.Adjustable Handle
G.Twist-N-Groom Shaft
B.Motor Cover
H.Adjustable Handle knob
C.Flower Guard
I. Plug Inlet
D.SharperBlade
J. Cord Hook
E. Shield
K.Power Switch
F. Telescopic Shaft
L. Handle
E
Technical Data
Power supply voltage – 120V~60Hz
Cutting diameter – 12.6 inch
Power consumption – 4.5A
Idle Speed – 7700rpm
4
SECRETS to a Long Lasting
SharperBlade™
Assembly
Before using the SharperBlade Electric Trimmer/Edger, follow
these instructions to assemble:
CONGRATULATIONS! YOU ARE ABOUT TO
EXPERIENCE A FASTER, EASIER, WAY OF
GROOMING YOUR LAWNS EDGE AND MANAGING
WEEDS.
1) Remove the trimmer and parts from the box.
First, you will notice that there are obvious differences between
your SharperBlade and string line, among which are size and
shape. These differences require you to operate your trimmer
slightly different:
Figure 1
1. Use MINIMAL pressure when edging against concrete,
brick, or stone. Since the SharperBlade is more ridged
than string, you may feel the need to put pressure on the
blade while edging. The more pressure you apply, the
FASTER the blade will wear. In contrast, the less pressure
you apply against hard surfaces, the LONGER the blade
will last! The SECRET is to keep the blade just off the hard
surface.
2. NEVER FORCE your SharperBlade. High speed along with
an impact against any hard surface may cause the blade
to buckle near the center hub and tear. The SECRET is to
allow the SharperBlade to do ALL the work without extra
effort.
2) Assemble the assist handle by fixing the knob (Figure 1).
Figure 2
LONG
Pressure =
LASTING
We sincerely hope you feel the SharperBlade has helped you
finish your work faster.
Warm regards,
Customer Service Staff
SharperBlade™
3) Insert the steel flower guard into the lower motor cover
and lock in place (Figure 2).
5
Installing or Changing Blade
Figure 3
Figure 5
screw knob
4) Place the Shield over the blade shaft and snap into place
(Figure 3).
1) Remove screw knob (Figure 5).
Figure 6
Figure 4
washer
5) Now the diameter of the protection area is 9 inches (Figure
4).
2) Remove the washer (Figure 6).
6) Ultimately you can remove the flower guard from the
motor cover. This will allow you maximum use of the
SharperBlade.
Figure 7
NOTE: Be careful when operating the machine while steel
flower guard is removed.
Sharper Blade
3) Assemble the SharperBlade to the Electric Trimmer/Edger
(Figure 7).
6
Operation
Figure 8
washer
Sharper Blade
4) Place the washer on the Blade (Figure 8).
Figure 9
mWARNING:
screw knob
Sharper Blade
Rocks or debris may ricochet or be thrown into eyes and face,
cause blindness, or other serious injury. Never lean over the
trimmer head and always wear eye protection.
When operating unit, stand as shown and check for the
following:
• Wear eye protection and heavy clothing.
• Hold the trigger handle with one hand and adjustable
handle with the other hand.
• Keep the trimmer below waist level.
5) Tighten the screw knob (Figure 9).
• Cut only from your right to your left to ensure debris is
thrown away from you. Without bending over, keep the
trimmer near and parallel to the ground.
mWARNING:
Use only SharperBlade Electric Trimmer/Edger™ replacement
blade. Other products will not work properly and will result in
improper cutting head function or can cause serious injury. Do
not use other materials such as steel blades, wire, string, rope,
etc. Other materials can break off during cutting and become a
dangerous missile that can cause serious injury.
TRIMMING
Hold the bottom of the trimmer head above the ground and at
an angle if desired. Allow only the blade to make contact. Do
not force blade into work area.
7
SWEEPING
Trimming
Fanning action can be used for quick and easy clean up. Keep
the line parallel to and above the surfaces being swept and
move the tool from side to side.
Sweeping
Blade above the ground
SCALPING
The scalping technique removes unwanted vegetation down
to the ground. Hold the bottom of the trimmer head about
3 inches (8 cm) above the ground and at an angle. Allow
the tip of the line to strike the ground around trees, posts,
monuments, etc. This technique increases blade wear.
EDGING
To change your SharperBlade Trimmer into an edger, you must
slide down the Twist-N-Groom Shaft (balck ring) ½”, and twist
to rotate the black ring 180° in a clockwise direction.
Scalping
0°
18
0°
MOWING
Your trimmer is ideal for mowing in places conventional lawn
mowers cannot reach. In the mowing position, keep the line
parallel to the ground. Avoid pressing the head into the ground
as this can scalp the ground and damage the tool.
Mowing
To convert from edger back to trimmer, hold the green handle,
slide the Twist-N-Groom Shaft (black ring) down ½”, and twist
to rotate the black ring 180° anti-clockwise direction.
8
• Store it out of the reach of children, in a stable and safe
position and in a dry place where the temperature is not too
hot or too cold.
Maintenance
Before carrying out any maintenance operations, cut off the
electric power supply by disconnecting the plug from the
extension cable.
• Store the trimmer in a location with minimal light, away from
direct sunlight.
• Do not store the grass trimmer resting on the floor. Hang it
by the upper handgrip instead, so that the guard does not
touch anything. The resting of the guard on a surface could
alter its shape and therefore its dimensions and safety
characteristics would be modified.
• Regular cleaning and maintenance of you grass trimmer will
ensure efficiency and prolong the life of your machine.
• After each cutting operation, take apart and clean out the
grass and soil from; the whole trimmer and guard.
• During operation, keep the air slots clean and free from
grass.
Service and Support
• Only use a cloth soaked with hot water and a soft brush to
clean the grass trimmer.
If your SharperBlade Electric Trimmer/Edger requires service or
maintenance, please call 1-866-766-9563 for assistance.
• Do not spray or wet the appliance with water.
Model and Serial Numbers
• Do not use detergents or solvents as these could ruin the
trimmer. The parts in plastic can easily be damaged by
chemical agents.
When contacting the company or reordering parts, you will
need to provide the model and serial numbers of your product.
These are found on the decal affixed to the housing or guard
of your SharperBlade Electric Trimmer/Edger. Copy these
numbers into the space provided below.
• If cutting blade no longer cuts or breaks, have this replaced
by contacting an authorized service center.
mCAUTION!
The blade can give deep cuts.
Record the following numbers from the housing or handle of your
new product:
• For repairs which have not been explained in these
instructions, contact an authorized service center.
Model #:
S B 6 0 1 E
Trouble-Shooting
Serial #:
mCAUTION!
Always disconnect the electric power supply before
conducting maintenance or troubleshooting.
• If the grass trimmer vibrates: remove the spool and clean
the slots, carefully remove any grass and weeds and so
forth. If vibration persists after reassembly, replace the
blade with a new one. In the evert of the problem not
disappearing, have the trimmer checked at an authorized
service center.
• If the trimmer does not start: check all the electrical
connections; make sure the safety circuit-breaker has not
been activated; check that a fuse has blown in your
electrical system. Take the trimmer to an authorized service
center if the trimmer does not start after completing the
checks.
Storage
Follow these recommendations for storing the grass trimmer.
• Carry out general cleaning of the grass trimmer and its
ancillary parts (see maintenance paragraph), this prevents
mould from forming.
9
A Two-Year Full Warranty
for residential use
in the United States and Canada
General Conditions:
Snow Joe, LLC warrants this product to the original purchaser for two years against defects in material or workmanship when used for
normal residential purposes. Snow Joe, LLC will repair any defect in material or workmanship, and repair or replace any defective part,
subject to the conditions, limitations, and exclusions set forth herein. Such repair or parts replacement will be free from charge to the
original purchaser except noted below.
The duration of the warranty applies only if the product is put to personal use around the household or residence. If the product is put
to any business use, commercial or industrial, then the duration of this warranty is 90 days from the date of original purchase. If any
product is rented or leased, the duration of the warranty is 90 days from the date of original purchase.
It is the owner’s responsibility to perform correctly all maintenance, and minor adjustments explained in the owner’s manual.
Electric Products:
To obtain a replacement electric powered unit or repair the existing electric powered unit, you must return the complete unit and
postage prepaid to: Snow Joe Return Center, 86 Executive Avenue, Edison, NJ 08817.
Gasoline / Battery Products:
Limitations
• Batteries are warranted only for the period of 12 months after the date of purchase on a prorated basis. Rechargeable batteries
will be replaced free from charge during the first 90 days. After the initial 90 days, batteries will be replaced at prorated cost to
the customer
• Idlers, cables, and electrical components are warranted to the original purchaser for use at household or residence for a period
of two years
Exclusions
• Snow Joe brand engines are covered under this warranty. All other engines and engine accessories are covered only by the
engine manufacturer’s warranty and are not covered by this warranty
• Parts used that are not genuine Snow Joe parts are not covered by this warranty
• Damages resulting from misuse, alteration, improper assembly, improper adjustment, neglect, or accident which requires repair
is not covered under this warranty
• Belts, augers, and tines are not covered under warranty – belts, augers, and tines wear out and can be purchased at
www.snowjoe.com or by calling 1-866-766-9563
Snow Joe, LLC may from time to time change the design of its products. Nothing contained in this warranty shall be construed as
obligating Snow Joe, LLC to incorporate such design changes into previously manufactured products, nor shall such changes be
construed as an admission that previous designs were defective.
This warranty is intended to cover product defects only. Snow Joe, LLC is not liable for indirect, incidental, or consequential damages
in connection with the use of the Snow Joe Products covered by this warranty. This warranty does not cover any cost or expense
incurred by the purchaser in providing substitute equipment or service during reasonable periods of malfunction or non-use of this
product, while waiting for completion of repairs under this warranty. Some states do not allow exclusions of incidental or consequential
damages, so the above exclusions may not apply in all states. This warranty may give you specific legal rights in your state.
If you wish to contact Snow Joe, please direct inquiries to the:
Customer Service Department
Snow Joe Center
86 Executive Avenue
Edison, NJ 08817
Customers who have purchased Snow Joe products exported from the United States and Canada should contact their Snow Joe
Distributor (Dealer) to obtain information applicable for your country, province, or state. If for any reason, you are not satisfied with the
distributor’s service, or if you have difficulty obtaining warranty information, contact your Snow Joe seller. If in the event your efforts
are unsatisfactory, please write to the Snow Joe Center at the above address.
If you have any questions about your product warranty, please call 1-866-SNOW-JOE or visit us online at www.snowjoe.com.
10