Biostar Hi-Fi B85N 3D Ver. 5.x User's manual

Hi-Fi B85N 3D/ Hi-Fi H81N 3D Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this user’s manual. All the brand and product names are trademarks of their respective companies.

Dichiarazione di conformità sintetica

Ai sensi dell’art. 2 comma 3 del D.M.

275 del 30/10/2002

Si dichiara che questo prodotto è conforme alle normative vigenti e soddisfa i requisiti essenziali richiesti dalle direttive

2004/108/CE, 2006/95/CE e

1999/05/CE quando ad esso applicabili

Short Declaration of conformity

We declare this product is complying with the laws in force and meeting all the essential requirements as specified by the directives

2004/108/CE, 2006/95/CE and

1999/05/CE whenever these laws may be applied

Table of Contents

Chapter 1: Introduction .........................................................................1

1.1

1.2

1.3

Before You Start......................................................................... 1

Package Checklist ..................................................................... 1

Motherboard Specifications ....................................................... 2

1.4

1.5

Chapter 2: Hardware Installation ..........................................................5

2.1

2.2

Rear Panel Connectors ............................................................. 3

Motherboard Layout .................................................................. 4

Install Central Processing Unit (CPU) ....................................... 5

Install a Heatsink ....................................................................... 7

2.3

2.4

2.5

2.6

Connect Cooling Fans............................................................... 8

Install System Memory .............................................................. 9

Expansion Slots....................................................................... 10

Jumper Setting ........................................................................ 12

2.7

Headers & Connectors ............................................................ 13

Chapter 3: UEFI BIOS & Software.......................................................18

3.1

3.2

UEFI BIOS Setup .................................................................... 18

BIOS Update ........................................................................... 18

3.3

Software................................................................................... 22

Chapter 4: Useful Help.........................................................................33

4.1

4.2

Driver Installation..................................................................... 33

AMI BIOS Beep Code.............................................................. 34

4.3

Troubleshooting....................................................................... 34

Appendix: Specifications in Other Languages .................................36

Arabic ......................................................................................................... 36

French ........................................................................................................ 38

German....................................................................................................... 40

Italian .......................................................................................................... 42

Japanese .................................................................................................... 44

Polish.......................................................................................................... 46

Portuguese ................................................................................................. 48

Russian....................................................................................................... 50

Spanish....................................................................................................... 52

Hi-Fi B85N 3D/ Hi-Fi H81N 3D

CHAPTER 1: INTRODUCTION

1.1 Before You Start

Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below:

Prepare a dry and stable working environment with sufficient lighting.

Always disconnect the computer from power outlet before operation.

Before you take the motherboard out from anti-static bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge.

Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board.

Do not leave any unfastened small parts inside the case after installation. Loose parts will cause short circuits which may damage the equipment.

Keep the computer from dangerous area, such as heat source, humid air and water.

The operating temperatures of the computer should be 0 to

45 degrees Celsius.

To avoid injury, be careful of:

Sharp pins on headers and connectors

Rough edges and sharp corners on the chassis

Damage to wires that could cause a short circuit

; Serial ATA Cable x2

; Rear I/O Panel for ATX Case x1

; User’s Manual x1

; Fully Setup Driver DVD x1

Note:

The package contents may be different due to the sales region or models in which it was sold. For more information about the standard package in your region, please contact your dealer or sales representative.

1

Motherboard Manual

2

CPU Support

Chipset

Memory

Storage

LAN

Audio Codec

USB

Expansion Slots

Rear I/Os

Internal I/Os

Specifications

Socket 1150 for Intel® Core i7 / i5 / i3 / Pentium / Celeron processor

Maximum CPU TDP (Thermal Design Power): 95Watt

* Please refer to www.biostar.com.tw

for CPU support list.

INTEL® B85 (Hi-Fi B85N 3D) INTEL® H81 (Hi-Fi H81N 3D)

Supports Dual Channel DDR3 1066/ 1333/ 1600

2 x DDR3 DIMM Memory Slot, Max. Supports up to 16 GB Memory

Each DIMM supports non-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3 module

* Please refer to www.biostar.com.tw

for Memory support list.

INTEL® B85:

2x SATA 6Gb/s Connector


1x mSATA Connector

INTEL® H81:



1x mSATA Connector

Supports AHCI Supports AHCI

2x Realtek RTL 8111G

10/ 100/ 1000 Mb/s auto negotiation, Half / Full duplex capability

ALC892

7.1 Channels, High Definition Audio, Biostar Hi-Fi

INTEL® B85:

4x USB 3.0 port (2 on rear I/Os and 2 via internal headers)


INTEL® H81:

2x USB 3.0 port (2 on rear I/Os)


1x PCIe 3.0 x16 Slot (x16), Hi-Fi B85N 3D

1x PCIe 2.0 x16 Slot (x16), Hi-Fi H81N 3D

1x PS/2 Mouse/Keyboard

1x HDMI Port

1x VGA Port

1x DVI Port

2x LAN port

4x USB 2.0 Port

2x USB 3.0 Port

5x Audio Jack

1x S/PDIF out

Hi-Fi B85N 3D

2x SATA 6.0Gb/s Connector


1x mSATA Connector

2x USB 2.0 Header

(each header supports 2 USB 2.0 ports)

1x USB 3.0 Header

Hi-Fi H81N 3D



1x mSATA Connector

2x USB 2.0 Header


1x 4-Pin Power Connector

Form Factor

OS Support


Specifications




1x CPU Fan Connector

1x System Fan Connector

1x Front Panel Header

1x Front Audio Header

1x Clear CMOS Header

1x Serial Port Header

1x Chassis Speaker Header

ATX Form Factor, 170 mm x 170 mm


1x CPU Fan Connector

1x System Fan Connector

1x Front Panel Header

1x Front Audio Header

1x Clear CMOS Header

1x Serial Port Header

1x Chassis Speaker Header

Windows 7/ 8

Biostar reserves the right to add or remove support for any OS with or without notice.

1.4 Rear Panel Connectors

Note1:

HDMI, DVI-D & VGA ports only work with an Intel® integrated Graphics Processor.

Note2:

Maximum resolution:

HDMI: 4096 x 2160 @24Hz, compliant with HDMI 1.4a

DVI: 1920 x 1200 @60Hz

VGA: 1920 x 1200 @60Hz

Note3:

The mainboard supports three onboard display outputs at same time.

Note4:

The audio jacks can be reconfigured to 5.1/7.1-channel audio by the audio driver.

3


Note1:

■ represents the 1 st

pin.

Note2:

The USB 3.0 header is only for Hi-Fi B85N 3D.

4


CHAPTER 2: HARDWARE INSTALLATION

2.1 Install Central Processing Unit (CPU)

Step 1:

Locate the CPU socket on the motherboard

Note1:

Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be damaged.

Note2:

The motherboard might equip with two different types of pin cap. Please refer below instruction to remove the pin cap.

Step 2:

Pull the socket locking lever out from the socket and then raise the lever up.

Step 3:

Remove the Pin Cap.

5


Step 4:

Hold processor with your thumb and index fingers, oriented as shown.

Align the notches with the socket. Lower the processor straight down without tilting or sliding the processor in the socket.

Note1:

The LGA1155 CPU is not compatible with LGA 1150 socket. Do not install a LGA 1155 CPU on the LGA 1150 socket.

Note2:

The CPU fits only in one correct orientation. Do not force the CPU into the socket to prevent damaging the CPU.

Step 5:

Hold the CPU down firmly, and then lower the lever to locked position to complete the installation.

6


Step 1:

Place the CPU fan assembly on top of the installed CPU and make sure that the four fasteners match the motherboard holes. Orient the assembly and make the fan cable is closest to the CPU fan connector.

Ensure the fastener slots are pointing perpendicular to the heatsink.

Step 2:

Press down two fasteners at one time in a diagonal sequence to secure the CPU fan assembly in place. As each fastener locks into position a click should be heard.

Note1:

Do not forget to connect the CPU fan connector.

Note2:

For proper installation, please kindly refer to the installation manual of your CPU heatsink.

7


These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer.

CPU_FAN1: CPU Fan Header

Pin Assignment

1 Ground

2 +12V

3

4

FAN RPM rate sense

Smart Fan Control (By Fan)

SYS_FAN1: System Fan Header

Pin Assignment

1 Ground

2 +12V

3 FAN RPM rate sense

Note:

CPU_FAN1, SYS_FAN1 support 4-pin and 3-pin head connectors. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin#2, and the black wire is Ground and should be connected to pin#1(GND).

8

DDR3 Modules


Step 1:

Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot.

Step 2:

Insert the DIMM vertically and firmly into the slot until the retaining clips snap back in place and the DIMM is properly seated.

Note:

If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.

9


Memory Capacity

DIMM Socket

Location

DDR3 Module

Total Memory Size

DDR3_A1 512MB/1GB/2GB/4GB/8GB

DDR3_B1 512MB/1GB/2GB/4GB/8GB

Max is 16GB.

Dual Channel Memory Installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status DDR3_A1 DDR3_B1

(O means memory installed, X means memory not installed.)

Note:

The DRAM bus width of the memory module must be the same (x8 or x16)

Install an Expansion Card

You can install your expansion card by following steps:

1. Read the related expansion card's instruction document before install the expansion card into the computer.

2. Remove your computer's chassis cover, screws and slot bracket from the computer.

3.

4.

5.

Place a card in the expansion slot and press down on the card until it is completely seated in the slot.

Secure the card’s metal bracket to the chassis back panel with a screw.

6.

7.

Replace your computer's chassis cover.

Power on the computer, if necessary, change BIOS settings for the expansion card.

Install related driver for the expansion card.

10


PEX16_1: PCI-Express Gen3 x16 Slot (Hi-Fi B85N 3D)

-

-

PCI-Express 3.0 compliant.

Maximum theoretical realized bandwidth of 16GB/s simultaneously per direction, for an aggregate of 32GB/s totally.

PEX16_1: PCI-Express Gen2 x16 Slot (Hi-Fi H81N 3D)

-

-

PCI-Express 2.0 compliant.

Maximum theoretical realized bandwidth of 8GB/s simultaneously per direction, for an aggregate of 16GB/s totally.

11


The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”.

Pin opened Pin closed Pin1-2 closed

JCMOS1: Clear CMOS Jumper

Placing the jumper on pin2-3, it allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the motherboard.

1 3

Pin 1-2 Close:

Normal Operation (default).

12

1 3

Pin 2-3 Close:

Clear CMOS data.

※

Clear CMOS Procedures:

1.

2.

3.

4.

5.

6.

Remove AC power line.

Set the jumper to “Pin 2-3 close”.

Wait for five seconds.

Set the jumper to “Pin 1-2 close”.

Power on the AC.

Load Optimal Defaults and save settings in CMOS.

JMPCI_TYP1: mSATA connector mode jumper

The jumper allows user to select mPCIe mode or mSATA mode for mSATA connector.

1 3

Pin 1-2 Close:

mPCIe Mode

1 3

Pin 2-3 Close:

mSATA Mode(default).


2.7 Headers & Connectors

ATXPWR1: ATX Power Source Connector

For better compatibility, we recommend to use a standard ATX 24-pin power supply for this connector. Make sure to find the correct orientation before plugging the connector.

Pin Assignment

13 +3.3V

14 -12V

15 Ground

16 PS_ON

17 Ground

18 Ground

19 Ground

20 NC

21 +5V

22 +5V

23 +5V

24 Ground

Pin Assignment

1 +3.3V

2 +3.3V

3 Ground

4 +5V

5 Ground

6 +5V

7 Ground

8 PW_OK

10 +12V

11 +12V

12 +3.3V

ATXPWR2: ATX Power Source Connector

The connector provides +12V to the CPU power circuit.

2

3

4

Pin Assignment

1 +12V

+12V

Ground

Ground

Note1:

Before you power on the system, please make sure that both ATXPWR1 and ATXPWR2 connectors have been plugged-in.

Note2:

Insufficient power supplied to the system may result in instability or the peripherals not functioning properly. Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices.

13


JPANEL1: Front Panel Header

This connector includes Power-on, Reset, HDD LED and Power LED connections.

It allows user to connect the PC case’s front panel switch functions.

1 N/A

3 HDD LED(+)

7 Ground

N/A

HDD LED

Reset Button

Assignment Function

2 Power LED (+)

4 Power LED (+)

Power LED

6 Power LED (-)

Power-On Button

10 Ground

JSPKR1: Chassis Speaker Header

Please connect the chassis speaker to this header.

Pin Assignment

1 +5V

2 N/A

3 N/A

4 Speaker

MSATA1: mSATA Connector (mPCIe Connector)

This connector can be used to connect a Solid-State Drive (SSD) for an internal storage device or a mPCIe expansion card.

Caution:

If the mechanical Interference occurs when using full-size card. You can remove the nut (A) to fit expansion card.

Note1:

The mSATA or mPCIe mode can be selected by jumper (JMPCI_TYP1).

Note2:

The default setting is mSATA mode.

14


SATA1-4: Serial ATA Connectors

These connectors connect to SATA hard disk drives via SATA cables. Please refer below table for SATA data transfer rates.

Models

Connectors

Hi-Fi B85N 3D

Hi-Fi H81N 3D

SATA1 SATA2 SATA3 SATA4

6Gb/s 3Gb/s 6Gb/s 3Gb/s

6Gb/s 3Gb/s NA 3Gb/s

Pin Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

7 Ground

JFRONT_USB3_1: Header for USB 3.0 Ports at Front Panel

This header allows user to add additional USB ports on the PC front panel, and also can be connected with a wide range of external peripherals.

Pin Assignment

1 VBUS0

2 SSRX1-

3 SSRX1+

4 Ground

5 SSTX1-

6 SSTX1+

7 Ground

8 D1-

9 D1+

10 ID

Note:

This header is only for Hi-Fi B85N 3D.

Pin Assignment

11 D2+

12 D2-

13 Ground

14 SSTX2+

15 SSTX2-

16 Ground

17 SSRX2+

18 SSRX2-

19 VBUS1

20 Key

15


F_USB1/2: Header for USB 2.0 Ports at Front Panel

This header allows user to add additional USB ports on the PC front panel, and also can be connected with a wide range of external peripherals.

Pin Assignment

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 NC

10 Key

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the chassis-mount front panel audio I/O which supports HD and AC’97 audio standards.

HD Audio

Pin Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5

6

Right line in

Jack Sense

8 Key

9

10

Left line in

Jack Sense

AC’97

Pin Assignment

1 Mic In

2 Ground

3 Mic Power

Power

5

6

RT Line Out

RT Line Out

7 Reserved

8 Key

9

10

LFT Line Out

LFT Line Out

Note1:

It is recommended that you connect a high-definition front panel audio module to this connector to avail of the motherboard's high definition audio capability.

Note2:

Please try to disable the "Front Panel Jack Detection" if you want to use an AC'97 front audio output cable. The function can be found via O.S. Audio Utility.

16


COM: Serial Port Header

The motherboard has a serial port header for connecting RS-232 Port.

Pin Assignment

6

7

Data set ready

Request to send

10 NC

17


CHAPTER 3: UEFI BIOS & SOFTWARE

3.1 UEFI BIOS Setup

z The BIOS Setup program can be used to view and change the BIOS settings for the computer. The BIOS Setup program is accessed by pressing the <DEL> key after the Power-On Self-Test (POST) memory test begins and before the operating system boot begins. z For further information of setting up the UEFI BIOS, please refer to the UEFI

BIOS Manual in the Setup DVD.

The BIOS can be updated using either of the following utilities: z BIOSTAR BIOS Flasher: Using this utility, the BIOS can be updated from a file on a hard disk, a USB drive (a flash drive or a USB hard drive), or a

CD-ROM. z BIOSTAR BIOS Update Utility: It enables automated updating while in the

Windows environment. Using this utility, the BIOS can be updated from a file on a hard disk, a USB drive (a flash drive or a USB hard drive), or a

CD-ROM, or from the file location on the Web.

BIOSTAR BIOS Flasher

BIOSTAR BIOS Flasher is a BIOS flashing utility providing you an easy and simple way to update your BIOS via USB pen drive.

Note1:

This utility only allows storage device with FAT32/16 format and single partition.

Note2:

Shutting down or resetting the system while updating the BIOS will lead to system boot failure.

Updating BIOS with BIOSTAR BIOS Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, copy and save the BIOS file into a USB flash (pen) drive.

3. Insert the USB pen drive that contains the BIOS file to the USB port.

4. Power on or reset the computer and then press <F12> during the POST process.

5. After entering the POST screen, the BIOS-FLASHER utility pops out. Choose [fs0] to search for the

BIOS file.

18


6. Select the proper BIOS file, and a message asking if you are sure to flash the BIOS file. Click Yes to start updating BIOS.

7. A dialog pops out after BIOS flash is completed, asking you to restart the system. Press the [Y] key to restart system.

8. While the system boots up and the full screen logo shows up, press <DEL> key to enter BIOS setup.

After entering the BIOS setup, please go to the

Save & Exit

, using the

Restore

Defaults

function to load Optimized Defaults, and select

Save Changes and

Reset

to restart the computer. Then, the BIOS Update is completed.

BIOS Update Utility (through the Internet)

1. Installing BIOS Update Utility from the DVD Driver.

2. Please make sure the system is connected to the internet before using this function.

3. Launch BIOS Update Utility and click the

Online Update

button on the main screen.

19


4. An open dialog will show up to request your agreement to start the

BIOS update. Click

Yes

to start the online update procedure.

5. If there is a new BIOS version, the utility will ask you to download it.

Click

Yes

to proceed.

6. After the download is completed, you will be asked to program

(update) the BIOS or not. Click

Yes

to proceed.

7. After the updating process is finished, you will be asked you to reboot the system. Click

OK

to reboot.



Save & Exit

, using the

Restore

Defaults



Reset


BIOS Update Utility (through a BIOS file)

1. Installing BIOS Update Utility from the DVD Driver.

2. Download the proper BIOS from http://www.biostar.com.tw/

3. Launch BIOS Update Utility and click the

Update BIOS

button on the main screen.

20


4. A warning message will show up to request your agreement to start the BIOS update. Click

OK

to start the update procedure.

5. Choose the location for your BIOS file in the system. Please select the proper BIOS file, and then click on

Open

. It will take several minutes, please be patient.

6. After the BIOS Update process is finished, click on

OK

to reboot the system.



Save & Exit

, using the

Restore

Defaults



Reset


Backup BIOS

Click the Backup BIOS button on the main screen for the backup of

BIOS, and select a proper location for your backup BIOS file in the system, and click

Save

.

21


3.3 Software

Installing Software

1. Insert the Setup DVD to the optical drive. The driver installation program would appear if the Auto-run function has been enabled.

2. Select , and then click on the respective software title.

3. Follow the on-screen instructions to complete the installation.

Launching Software

After the installation process is completed, you will see the software icon showing on the desktop. Double-click the icon to launch it.

Note1:

All the information and content about following software are subject to be changed without notice. For better performance, the software is being continuously updated.

Note2:

The information and pictures described below are for your reference only. The actual information and settings on board may be slightly different from this manual.

BIOScreen Utility

This utility allows you to personalize your boot logo easily. You can choose BMP as your boot logo so as to customize your computer.

Please follow the step-by-step instructions below to update boot logo: z Load

：

Choose the picture as the boot logo. z Transform

：

Transform the picture for BIOS and preview the result. z Update

：

Write the picture to BIOS Memory to complete the update.

22


eHot-Line

eHot-Line is a convenient utility that helps you to contact with our Tech-Support system.

This utility will collect the system information which is useful for analyzing the problem you may have encountered, and then send these information to our tech-support department to help you fix the problem.

Note:

Before you use this utility, please set Outlook Express as your default e-mail client application program.

* must provide. Without this information, you may not be able to send out the mail.

This block will show the information which would be collected in the mail.

* Describe condition of your system.

* Select your area or the area close to you.

Provide the e-mail address that you would like to send the copy to.

*

Provide the name of the memory module manufacturer.

Send the mail out.

Exit this dialog.

Save these information to a .txt file

Provide the name of the power supply manufacturer and the model no.

After filling up this information, click

“

Send

” to send the mail out. A warning dialog would appear asking for your confirmation; click “

Send

” to confirm or “

Do Not Send

” to cancel.

If you want to save this information to a .txt file, click “

Save As…

” and then you will see a saving dialog appears asking you to enter file name.

23


Enter the file name and then click

“

Save

”. Your system information will be saved to a .txt file.

Open the saved .txt file, you will see your system information including motherboard/BIOS/CPU/video/ device/OS information. This information is also concluded in the sent mail.

Note1:

We will not share customer’s data with any other third parties, so please feel free to provide your system information while using eHot-Line service.

Note2:

If you are not using Outlook Express as your default e-mail client application, you may need to save the system information to a .txt file and send the file to our tech support with other e-mail application. Go to the following website http://www.biostar.com.tw/app/en/about/contact.php

for getting our contact information.

24


Smart EAR 3D

Hi-Fi 3D Audio Requirements:

1. A chassis with front audio output jacks

2. An earphone or a headphone

3. Speakers

4. Windows 7 or Windows 8 operation system

Installation Guide:

1. Make sure the front audio cable of the chassis connected to the front audio header of the motherboard properly.

2. Install the Smart Ear 3D Utility from the driver DVD.

3. Connect the earphone or headphone to the front audio jack of the chassis for

Smart Gain and 3D Sound Field functions.

4. Connect the speakers to

line out port

(green color) of rear panel for Smart

PREAMP function.

Note1:

If you want to use an AC'97 front audio output cable, please disable the "Front Panel Jack

Detection" setting. This setting can be found via O.S. Audio Utility.

25


Smart EAR 3D Utility:

1.

Rear Panel Audio Output Indicator:

It displays a blue light when the audio

2.

3. output is from rear panel ports.

3D Sound Field Button:

There are six sound environment options for achieving realistic listening experience. It displays a blue light when the 3D Sound Field is enabled.

Smart PREAMP Button:

Click this switch to turn on or off the Smart PREAMP function.

Mute Button:

To disable system sound

Control Button:

It allows you to set utility preference.

4.

5.

6.

7.

Volume Control Knob:

The volume can be finely adjusted by turning the knob either clockwise or anti-clockwise to increase or decrease system volume accordingly.

Headphone Hi/Mid/Low Gain Switch:

It allows you to select headphone gain settings or you can let the software auto adjust headphone gain setting appropriate for your headphones. The Smart Gain function will be enabled when the 3D Sound Field Button is turned on.

Front Panel Audio Output Indicator:

It displays a blue light when the audio 8.

9. output is from front panel port.

Exit Button:

Exit the application

10.

Minimize Button:

Minimize the application window to the taskbar

11.

Information Button:

Get information of the application

12.

Smart PREAMP or Smart Gain ON/OFF Indicator:

When the Rear Panel

Audio Output Indicator is lit, it shows Smart PREAMP on/off status. When the

Front Panel Audio Output Indicator is lit, it shows Smart Gain on/off status.

Note1:

The 3D Sound Field function is only for front panel audio output.

Note2:

The Smart PREAMP function is only for rear panel audio output.

Note3:

When both rear and front panels are connected with audio devices, the default audio output is from front panel.

26


Smart Connect Technology

Intel® Smart Connect Technology is designed to update programs by periodically waking your computer from sleep/standby mode for a short time. This function works with applications that automatically get their data from the Internet.

System Requirement:

z Intel Smart Connect Technology enabled in BIOS Setup z Set the “ACPI Sleep State” to S3 in BIOS Setup. z Windows 7 and Windows 8 z

Normal internet connection

Configuring Intel Smart Connect Technology

Step 1:

After installing the operating system and motherboard drivers, install the Intel

Smart Connect Technology application. Restart your computer when completed.

Step 2:

Click on start menu and input "regedit" in the search bar. Press enter to open the registry editor. Look for the following directory in the registry editor:

Computer\HKEY_LOCAL_MACHINE\SOFTWARE\Intel\Intel Smart Connect Technology

Right-click on

Intel Smart Connect Technology

and select

New > Key

. Type “OEM”.

Note:

Intel Smart Connect Technology is for S3 mode only. During the updating process, the monitor will not light up and no sound will be output from the speaker.

Step 3:

As shown in the screenshot below, right-click on OEM, select New >

Multi-String Value, and type “WhiteList”. Double-click WhiteList and type the application name to be added in Edit Multi-String. For example, to add Microsoft Live

Mail, type “wlmail.exe”. Restart your computer when completed.

Step 4:

After completing the steps above, go to Start\All Programs\Intel and launch

Intel(R) Smart Connect Technology.

27


Basic and advanced settings

Basic Tab

Update Frequency slider:

This slider bar sets the amount of time the feature waits to wake your computer and update your applications. Move the slider in the user interface to change the frequency. The slider bar can be set to wake and update your computer from every 15 to

60 minutes. The longer the time between updates the less power the feature consumes.

Reset All to Defaults button:

This button is designed to reset Intel® Smart Connect

Technology back to the original factory setting for wake frequency.

Advanced Tab

28

Extended Power Savings:

You can set a time for Intel Smart Connect Technology to work in

Extended Power Savings mode. This night time mode updates your computer every two hours, saving power for the times you are not using your computer.


Rapid Start Technology

Intel® Rapid Start technology enables your system to get up and running faster from even the deepest sleep, saving time and power consumption. Feel secure knowing that your system will still resume to working conditions in the event of unexpected power loss while in sleep mode.

System Requirement:

z

An Intel® SATA SSD (SATA Gen2 or Gen3. Preferably Gen3, and 80 GB or larger) z

Windows 7 and Windows 8

Note1:

Please visit below webpage for more details about operating systems supporting http://www.intel.com/p/en_US/support

Note2:

The Rapid Start Technology is NOT supported by H81 chipset.

Installing Intel® RST:

Step 1: BIOS Setting

1-1

Go to [Advanced Menu] > [ACPI Settings], and set [ACPI Sleep State] to S3

(Suspend to RAM)

1-2

Go to [Advanced Menu] > [SATA Configuration], and set [SATA Mode

Selection] to AHCI

1-3

Go to [Advanced Menu] and set [Intel(R) Rapid Start Technology] to Enabled

1-4

Save your changes, and then exit the BIOS Setup.

Step 2: Operating System Installation

Step 3: Installing Intel® Rapid Start Application

3-1

Insert the setup Driver DVD into your optical drive. Click “Intel Rapid Start

Technology” to launch the program.

3-2

Below window will pop-out, then click “Create Disk” to star disk partition. After disk partition finished, please click “OK” then system will reboot automatically.

29


3-3

After rebooting, the system will setup Intel® Rapid Start Technology automatically. We recommend you restart the system after this installation is complete,

30

Step 4: Configuring Intel® Rapid Start Application

Launch the Intel® Rapid Start Technology Manager application from [Start] > [All

Programs] > [Intel] or click the icon in the notification area.


Intel® Small Business Advantage

Intel Small Business Advantage (Intel SBA) provides an out-of-the-box hardware-based security and productivity suite designed for the small business user.

Software Monitor

Software Monitor helps keep critical security software running by monitoring it at the hardware level and alerting the business if there has been an attack. The Software

Monitor also maintains an event log that shows status information and any errors generated, so businesses can know what happened.

Data Backup and Restore

Data Backup and Restore provides reliable after-hours backup of critical data using the local maintenance timer to power on the computer. Data can be backed up to a designated location.

USB Blocker

The optional USB Blocker lets businesses control access to their infrastructure, preventing unauthorized USB devices or file imports or exports on company computers.

PC Health Center

PC Health Center can schedule and do PC maintenance tasks after hours, without interrupting employee work time. Tasks such as updating the operating system, deleting temporary internet files, and running disk defragmentation can be done at night.

PC Health Center works even if the computer is powered-down, as long as it is plugged in.

Energy Saver

With the optional Energy Saver, businesses can save energy by scheduling PCs to power-down at the end of the day and turn on before the work day begins - ready for employees as they arrive in the morning.

Supported Operating Systems:

Windows 7 and Windows 8

Note1:

Please visit below webpage for more details about operating systems supporting http://www.intel.com/p/en_US/support

Note2:

The Small Business Advantage is NOT supported by H81 chipset.

31


Installing Intel SBA

This procedure describes how to install Intel SBA.

1. Logon to the computer with a user that has administrator privileges.

2. Copy the Setup.exe file to the computer.

Setup.exe.

The Welcome to the Setup Program window opens.

4. Click Next. The installer starts the installation and the Setup Progress window opens showing the progress of the installation. When installation is complete, the installer starts the Intel SBA service and the Next button is enabled.

32

5. Click Next. The Setup Is Complete window opens.

6. Click Finish. The installer closes.


CHAPTER 4: USEFUL HELP

After you installed your operating system, please insert the Fully Setup Driver

DVD into your optical drive and install the driver for better system performance.

You will see the following window after you insert the DVD

The setup guide will auto detect your motherboard and operating system.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system. Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver DVD.

Click on the Manual icon to browse for available manuals.

Note1:

If this window didn’t show up after you insert the Driver DVD, please use file browser to locate and execute the file SETUP.EXE under your optical drive.

Note2:

You will need Acrobat Reader to open the manual file. Please download the latest version of

Acrobat Reader software from http://get.adobe.com/reader/

33


4.2 AMI BIOS Beep Code

Boot Block Beep Codes

Number of Beeps

Continuing

Description

Memory sizing error or Memory module not found

POST BIOS Beep Codes

Number of Beeps Description

8 Display memory error (system video adapter)

4.3 Troubleshooting

Probable Solution

1. There is no power in the system. Power

LED does not shine; the fan of the power supply does not work

2. Indicator light on keyboard does not shine.

System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running.

1. Make sure power cable is securely plugged in.

3. Contact technical support.

Using even pressure on both ends of the

DIMM, press down firmly until the module snaps into place.

System does not boot from a hard disk drive, but can be booted from optical drive.

System only boots from an optical drive.

Hard disks can be read, applications can be used, but system fails to boot from a hard disk.

Screen message shows “Invalid

Configuration” or “CMOS Failure.”

System cannot boot after user installs a second hard drive.

1. Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the drive type in the standard CMOS setup.

2. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time.

1. Back up data and applications files.

2. Reformat the hard drive. Re-install applications and data using backup disks.

Review system’s equipment. Make sure correct information is in setup.

1. Set master/slave jumpers correctly.

2. Run SETUP program and select correct drive types. Call the drive manufacturers for compatibility with other drives.

34


CPU Overheated

If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.

2. Wait for seconds.

3. Power on the system again.

35


APPENDIX: Specifications in Other Languages

Arabic

تﺎﻔﺻاﻮﻤﻟا

Intel® Core i7 / i5 / i3 / Pentium / Celeron ىد مإ ﻪﻳا ﺞﻟﺎﻌﻤﻟ 1150 ﺬﺧﺄﻤﻟا

.

طاو 95 :( thermal design power – TDP ) ﺞﻟﺎﻌﻤﻟا ﻢﻴﻤﺼﺗ ﻲﻓ ﺔﻳراﺮﺤﻟا ﺔﻗﺎﻄﻠﻟ ﻰﺼﻗﻷا ﺪﺤﻟا

.

CPU ﺞﻟﺎﻌﻤﻟا ﻢﻋد ﺔﻤﺋﺎﻘﻟ www.biostar.com.tw ﻊﻗﻮﻤﻟا ﻰﻟإ عﻮﺟﺮﻟا ﻰﺟﺮﻳ *

INTEL® B85 (Hi-Fi B85N 3D) IINTEL® H81 (Hi-Fi H81N 3D)

.

را .

يد .

يد ﺔﺟودﺰﻣ ةﺎﻨﻗ ﻢﻋﺪﺗ DDR3 1066/ 1333/ 1600

ةﺮآاذ ﺖﻳﺎﺑﺎﺠﻴﺟ 16 ﻰﺼﻗأ ﺪﺤآ ﻞﻤﺤﺘﺗ ، DIMM ﺔﺟودﺰﻤﻟا ةﺮآاﺬﻟا تﺎﺤﺘﻓ DDR3 .

را .

يد .

يد 2x

DDR3 را .

يد .

يد ﺖﻳﺎﺑﺎﺠﻴﺟ 8 / 4 / 2 / 1 / ﺖﻳﺎﺑ ﺎﺠﻴﻣ 512 ECC نود ﻞﻤﺤﺘﺗ DIMM ﺔﺟودﺰﻣ ﺔﺤﺘﻓ ﻞآ

.

ةﺮآاﺬﻟا ﻢﻋد ﺔﻤﺋﺎﻘﻟ www.biostar.com.tw ﻊﻗﻮﻤﻟا ﻰﻟإ عﻮﺟﺮﻟا ﻰﺟﺮﻳ *

INTEL® B85

ﺔﻴﻧﺎﺜﻟا / ﺖﻳﺎﺑ ﺎﺠﻴﺟ 6 SATA ﺎﺗﺎﺳ 2x ﺔﻠﺻو

INTEL® H81



MSATA 1x ﻞﺻﻮﻣ

AHCI ﺪﻳار ﻞﻤﺤﺘﺗ



AHCI ﺪﻳار ﻞﻤﺤﺘﺗ

REALTEK RTL 8111G ل تر ﻚﻴﺘﻟﺎﻴﻳر x 2

ﺔﺟودﺰﻤﻟا ىﻮﺼﻘﻟا ةرﺪﻘﻟا / ﻒﺼﻨﻟا ، ﻲﺋﺎﻘﻠﺗ ﺪﻳﺪﺤﺗ ، ﺔﻴﻧﺎﺜﻟا / ﺖﻳﺎﺑﺎﺠﻴﻣ 1000 / 100 / 10

ALC892

Biostar Hi-Fi , ﺔﻗﺪﻟا ﺔﻴﻟﺎﻋ تاﻮﻨﻗ 7.1

INTEL® B85

ﻲﻓ 2 ) 3.0

USB مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ x 4 ﺬﻓﺎﻨﻣ

عزﻮﻤﻟا لﻼﺧ ﻦﻣ 2 و ﺔﻴﻔﻠﺨﻟا جرﺎﺨﻤﻟاو ﻞﺧاﺪﻤﻟا

( ﻲﻠﺧاﺪﻟا

ﻲﻓ 4 ) 2.0


عزﻮﻤﻟا لﻼﺧ ﻦﻣ 4 و ﺔﻴﻔﻠﺨﻟا جرﺎﺨﻤﻟاو ﻞﺧاﺪﻤﻟا


(x16)

(x16)

16

16 x x

2.0

3.0

PCIe

PCIe

ﻲﻓ

INTEL® H81

2 ) 3.0


( ﺔﻴﻔﻠﺨﻟا جرﺎﺨﻤﻟاو ﻞﺧاﺪﻤﻟا

4 ) 2.0


عزﻮﻤﻟا لﻼﺧ ﻦﻣ 4 و ﺔﻴﻔﻠﺨﻟا جرﺎﺨﻤﻟاو ﻞﺧاﺪﻤﻟا ﻲﻓ


ﺔﻴﻓﺎﺿﻹا تﺎﻘﺤﻠﻤﻟا ﺬﻔﻨﻣ ﺔﺤﺘﻓ x 1, Hi-Fi H81N 3D

ﺔﻴﻓﺎﺿﻹا تﺎﻘﺤﻠﻤﻟا ﺬﻔﻨﻣ ﺔﺤﺘﻓ x 1, Hi-Fi B85N 3D

ﺢﻴﺗﺎﻔﻤﻟا ﺔﺣﻮﻟ / سوﺎﻤﻟا PS/2 x 1

حﻮﺿﻮﻟا ﻲﻟﺎﻌﻟا دﺪﻌﺘﻣ ﻂﻴﺳو HDMI x 1 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ

VGA ﻲﺋﺮﻤﻟا ضﺮﻌﻟا ﺔﻣﻮﻈﻨﻣ x 1 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ

DVI ﺔﻴﻤﻗر ﺔﻴﺋﺮﻣ ﺔﻬﺟاو x 1 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ

LAN ﺔﻴﻠﺤﻤﻟا ﺔﻜﺒﺸﻟا x 2 دﺪﻋ ﻞﻴﺻﻮﺘﻟ ﺔﺤﺘﻓ

2.0

USB مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ x 4 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ

3.0

USB مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ x 2 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ

تﻮﺼﻠﻟ كﺎﺟ x 5 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ

SPDIF x 1 دﺪﻋ ﻞﻴﺻﻮﺗ ﺔﺤﺘﻓ

ﺔﺠﻟﺎﻌﻤﻟا

USB

LAN

ةﺪﺣو ةﺪﻋﺎﻗ

ﺔﻳﺰآﺮﻤﻟا

ﺢﺋاﺮﺸﻟا

ﺔﻴﻠﺤﻣ

ﻲﺗﻮﺼﻟا

مﺎﻋ

ﺔﻋﻮﻤﺠﻣ

ةﺮآاﺬﻟا

ﻦﻳﺰﺨﺘﻟا

ﺰﻴﻣﺮﺘﻟا

ﻞﺴﻠﺴﺘﻣ

ﻊﺳﻮﺘﻟا

ﺔﻜﺒﺷ

ﻞﻗﺎﻧ

تﺎﺤﺘﻓ

ﺔﻴﻔﻠﺨﻟا جرﺎﺨﻤﻟاو ﻞﺧاﺪﻤﻟا

36


تﺎﻔﺻاﻮﻤﻟا

Hi-Fi B85N 3D


ﺔﻴﻧﺎﺜﻟا / ﺖﻳﺎﺑﺎﺠﻴﺟ 6 SATA x 2 ﺔﻠﺻو


عزﻮﻣ ﻞآ ) 2.0

USB مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ x 2 عزﻮﻣ

( 2.0

USB مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ ﻦﻴﺘﺤﺘﻓ ﻞﻤﺤﺘﻳ



( 3.0

USB مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ ﻦﻴﺘﺤﺘﻓ ﻞﻤﺤﺘﻳ

ﺲﻴﺑﺎﺑد 4 x 1 ﺔﻗﺎﻄﻠﻟ ﺔﻠﺻو

سﻮﺑد 24 x 1 ﺔﻗﺎﻄﻠﻟ ﺔﻠﺻو

ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺪﻳﺮﺒﺗ ﺔﺣوﺮﻣ x 1 ﺔﻠﺻو

ﺔﻣﻮﻈﻨﻤﻟا ﺪﻳﺮﺒﺗ حواﺮﻣ x 1 ﺔﻠﺻو

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا x 1 عزﻮﻣ

ﻲﻣﺎﻣﻷا تﻮﺼﻟا x 1 عزﻮﻣ

ﺮﺷﺎﺒﻣ سﻮﻤﻴﺳ x 1 عزﻮﻣ

ﺔﻴﻠﺴﻠﺴﺗ ﺔﺤﺘﻓ x 1 عزﻮﻣ

ﺔﻌﺑﺎﻄﻠﻟ ﺔﺤﺘﻓ x 1 عزﻮﻣ

ﻞﺻﻮﻣ ﺲﻴﺋر ﻞﻜﻴﻬﻟا x 1 عزﻮﻣ

ﺔﻌﺑﺎﻄﻠﻟ

Hi-Fi H81N 3D






( 2.0

USB مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ ﻦﻴﺘﺤﺘﻓ ﻞ

ﺲﻴﺑﺎﺑد 4

سﻮﺑد 24 x

ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺪﻳﺮﺒﺗ ﺔﺣوﺮﻣ x

ﺔﻣﻮﻈﻨﻤﻟا ﺪﻳﺮﺒﺗ حواﺮﻣ

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا x

ﻲﻣﺎﻣﻷا تﻮﺼﻟا x

ﺮﺷﺎﺒﻣ سﻮﻤﻴﺳ x

ﺔﻴﻠﺴﻠﺴﺗ ﺔﺤﺘ x 1 ﺔﻗﺎﻄﻠﻟ ﺔﻠﺻو

1 ﺔﻗﺎﻄﻠﻟ ﺔﻠﺻو

ﻓ x 1 عزﻮﻣ

ﺔﺤﺘﻓ x 1 ﺔﻠﺻو x

ﻞﺻﻮﻣ ﺲﻴﺋر ﻞﻜﻴﻬﻟا x

1 ﺔﻠﺻو

1 عزﻮﻣ

1 عزﻮﻣ

1 عزﻮﻣ

1

ﻤﺤﺘﻳ

عزﻮﻣ

1 عزﻮﻣ

ﻢﻣ 170 x ﻢﻣ 170 ، ATX ﺔﻣﺪﻘﺘﻤﻟا ﺎﻴﺟﻮﻟﻮﻨﻜﺘﻟا دﺪﻣ ﻞﻜﺷ ﻞﻣﺎﻋ

8 زوﺪﻨﻳو / 7 زوﺪﻨﻳو

.

رﺎﻈﻧأ نوﺪﺑ وأ ﻊﻣ ﻞﻴﻐﺸﺗ مﺎﻈﻧ يﻷ ﻢﻋﺪﻟا ﺔﻟزأ وأ ﺔﻓﺎﺿ إ ﻖﺤﺑ ﻆﻔﺘﺤﺗ BIOSTAR رﺎﺘﺳﻮﻴﺑ

ﺔﻴﻠﺧاﺪﻟا جرﺎﺨﻤﻟاو ﻞﺧاﺪﻤﻟا

ﻞﻜﺸﻟا ﻞﻣﺎﻋ

ﺔﻣﻮﻋﺪﻤﻟا ﻞﻴﻐﺸﺘﻟا ﺔﻤﻈﻧأ

37


French

Support Unité

Centrale

Jeu de puces

Mémoire

Stockage

Réseau local

Codec audio

USB

Connecteur d’extension

I/O arrirèes

Spécifications

Socket 1150 Processeurs Intel® Core i7 / i5 / i3 / Pentium / Celeron

Enveloppe thermique Unité Centrale maximum : 95Watt

* Veuillez vous reporter à www.biostar.com.tw pour la liste des supports modèles d'Unité

Centrale.


Supporte mémoire DDR3 double canal 1066/ 1333/ 1600

Banc de mémoire 2 x DDR3 DIMM, Supporte max. jusqu’à une mémoire de 16 GB

Chaque module DIMM supporte module DDR3 non-ECC 512MB/ 1/ 2/ 4/ 8 GB

* Veuillez vous reporter à www.biostar.com.tw

pour la liste des soutien de la mémoire.

INTEL® B85:

Connecteur 2 x SATA 6Gb/s


Connecteur 1x mSATA

INTEL® H81:



Connecteur 1x mSATA

Supporte système AHCI Supporte système AHCI


10/ 100/ 1000 Mb/s auto négociation, capacité bidirectionnelle à l'alternat / bidirectionnelle simultanée

ALC892

Canaux 7.1, écoute audio de haute définition, Biostar Hi-Fi

INTEL® B85:

Port 4x USB 3.0 (2 sur les I/O arrières et 2 en interne)


INTEL® H81:

Port 2x USB 3.0 (2 sur les I/O arrières)


1x PCIe 3.0 x16 Fente (x16), Hi-Fi B85N 3D

1x PCIe 2.0 x16 Fente (x16), Hi-Fi H81N 3D

1x PS/2 Clavier/Souris

1x Port HDMI

1x Port VGA

1x Port DVI

2x port LAN

4x Port USB 2.0

2x Port USB 3.0

5x entrées audio

1x Connecteur sortie S/PDIF

38

I/O en interne

Facteur d'encombrement

Support SE


Spécifications

Hi-Fi B85N 3D

2x Connecteur SATA 6.0Gb/s


1x mSATA Connecteur

2x embases USB 2.0

(chaque embase supporte 2 Ports USB 2.0)

1x embase USB 3.0


1x 4-Broche de carte


1x Connecteur ventilateur unité centrale

1x Connecteur ventilateur système

1x Fiche panneau avant

1x Fiche audio avant

1x Fiche mémoire CMOS vide

1x Embase port série

1x Embase port imprimante

1x Connecteur Audio du panneau avant

Hi-Fi H81N 3D



1x mSATA Connecteur

2x embases USB 2.0




1x Connecteur ventilateur unité centrale

1x Connecteur ventilateur système

1x Fiche panneau avant

1x Fiche audio avant

1x Fiche mémoire CMOS vide

1x Embase port série

1x Embase port imprimante

1x Connecteur Audio du panneau avant

Facteur d'encombrement ATX, 170 mm x 170 mm

Windows 7/ 8

Biostar se réserve le droit d’ajouter ou d'enlever le support pour toute SE avec ou sans préavis.

39


German

CPU-Unterstützung

Chipset

Festplattenspeicher

Arbeitsspeicher

LAN

Audio-Codec

USB

Spezifikationen

Anschluss-1150 für Intel® Core i7 / i5 / i3 / Pentium / Celeron Prozessor

Maximale CPU TDP (Thermal Design Power): 95 Watt

* Bitte konsultieren Sie www.biostar.com.tw

für CPU-Unterstützungsliste


Unterstützt zweikanaliges DDR3 1066/ 1333/ 1600

2 x DDR3 DIMM-SpeicherSlot, Max. Uterstützung bis zu 16 GB-Speicher

Jedes DIMM unterstützt nicht-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3-Module

* Bitte konsultieren Sie www.biostar.com.tw

für für Speicherunterstützung Liste.

INTEL® B85:

2x SATA 6Gb-Verbindung


1x mSATA Verbindung

Unterstützt AHCI

INTEL® H81:



1x mSATA Verbindung

Unterstützt AHCI


10/ 100/ 1000 Mb Auto-Negotiation, Halb- / Voll-Duplex-fähig

ALC892

7.1 Kanäle, HD-Audio, Biostar Hi-Fi

INTEL® B85:

4x USB 3.0-Port (2 hintere I/Os und 2 via interne Header)


INTEL® H81:

2x USB 3.0-Port (2 hintere I/Os)


Erweiterungsanschl

üsse

1x PCIe 3.0 x16-Slot (x16), Hi-Fi B85N 3D

1x PCIe 2.0 x16-Slot (x16), Hi-Fi H81N 3D

Hintere I/Os

Interne I/Os

1x PS/2- Tastatur/Maus

1x HDMI-Port

1x VGA-Port

1x DVI-Port

2x LAN-Port

4x USB 2.0-Port

2x USB 3.0-Port

5x Audio Jack

1x S/PDIF-Auswurfsverbindung

Hi-Fi B85N 3D

2x SATA 6.0Gb/s-Verbinung


1x mSATA Verbindung

2x USB 2.0-Header

(jeder Header unterstützt 2 USB 2.0-Ports)

1x USB 3.0-Header


1x 4-Pin-Stromverbindung


Hi-Fi H81N 3D



1x mSATA Verbindung

2x USB 2.0-Header




1x CPU-Ventilatorverbindung

1x System-Ventilatorverbindung

40

Formfaktor

OS-Unterstützung


Spezifikationen

1x CPU-Ventilatorverbindung

1x System-Ventilatorverbindung

1x Header für Frontpanel

1x Header für Frontaudio

1x Header für klares CMOS

1x Serieller Port-Header

1x Header für Druckeranschluss

1x Header für Frontpanel

1x Header für Frontaudio

1x Header für klares CMOS

1x Serieller Port-Header

1x Header für Druckeranschluss

1x Chassis Lautsprecher-Header

1x Chassis Lautsprecher-Header

ATX Formfaktor, 170 mm x 170 mm

Windows 7/ 8

Biostar reserves the right to add or remove support for any OS with or without notice.

41


Italian

Supporto processore

Tipo scheda

Memoria

Memorizzazione

Catena

Codec Audio

USB

Specificazioni

Slot 1150 per processore Intel® Core i7 / i5 / i3 / Pentium / Celeron

Alimentazione di Proiezione Termico (TDP – Thermal Design Power): 95Watt

* Si prega di consultare www.biostar.com.tw

per la lista di supporto del processore.


Supporta DDR3 1066/ 1333/ 1600 Doppio Canale

2 x DDR3 DIMM Slot di Memoria Supporta fino a 16 GB Memoria

Ogni DIMM supporta non-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3 moduli

* Si prega di consultare www.biostar.com.tw

per la lista di supporto del memoria.

INTEL® B85:

Connettore 2x SATA 6Gb/s


Connettore 1x mSATA

Supporta AHCI

INTEL® H81:



Connettore 1x mSATA

Supporta AHCI


10/ 100/ 1000 Mb auto negoziazione, capacita di duplex Meta / Completo

ALC892

Canali Audio di Alta Definizione 7.1, Biostar Hi-Fi

INTEL® B85: INTEL® H81:

Slot 4x USB 3.0 (2 nei ingressi/ uscite posteriore e 2 da distributori interni)


Slot 2x USB 3.0 (2 nei ingressi/ uscite posteriore)


Slot di espansione

Slot 1x PCIe 3.0 x16 (x16), Hi-Fi B85N 3D

Slot 1x PCIe 2.0 x16 (x16), Hi-Fi H81N 3D

Ingressi/ Uscite

Posteriore

Tastiera / Mouse 1x PS/2

Slot 1x HDMI

Slot 1x VGA

Slot 1x DVI

Slot 2x LAN

Slot 4x USB 2.0

Slot 2x USB 3.0

Jack audio 5x

Connettore esterno S/PDIF x1

42

Ingressi/ Uscite

Interni

Fattore di Forma

Supporto SO


Specificazioni

Hi-Fi B85N 3D

Connettore 2x SATA 6.0Gb/s


Connettore 1x mSATA

Distributore 2x USB 2.0

(ogni distributore supporta 2 slot USB 2.0)


Hi-Fi H81N 3D



Connettore 1x mSATA



Connettore con 4 pin x1




Connettore Ventilatore processore x1

Connettore Ventilatore Sistema x1

Distributore Pannello Frontale x1

Distributore Audio Frontale x1

Distributore CMOS Diretto x1


Connettore Ventilatore processore x1

Connettore Ventilatore Sistema x1

Distributore Pannello Frontale x1

Distributore Audio Frontale x1

Distributore CMOS Diretto x1

Distributore Slot Serie x1

Distributore Slot Stampante x1

Distributore casse telaio x1 Distributore Slot Serie x1

Distributore Slot Stampante x1

Distributore casse telaio x1

Fattore di Forma ATX, 170 mm x 170 mm

Windows 7/ 8

Biostar si riserva il diritto di aggiungere o ritirare il supporto per qualsiasi SO con o senza preavviso.

43


Japanese

CPU

サポート

チップセット

メモリ

保存スペース

LAN

オーディオコーデ

ック

USB

仕様

Intel® Core i7 / i5 / i3 / Pentium / Celeron

プロセッサの

Socket 1150

最大

CPU TDP

（

Thermal Design Power

最大放熱量）

:95 W

*CPU

サポートリストについては、 www.biostar.com.tw

を参照してください。


デュアルチャンネル

1066/ 1333/ 1600

をサポート

2 x DDR3 DIMM

メモリスロット、最大

16 GB

メモリまでサポート

各

DIMM

は、非

-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3

モジュールをサポートしています

*

サポートされているメモリのリストについては、 www.biostar.com.tw

を参照してくだ

さい。

INTEL® B85:

2x SATA 6Gb/s

コネクタ

2x SATA 3Gb/s

コネクタ

1x mSATA

コネクタ

AHCI

のサポート

INTEL® H81:

1x SATA 6Gb/s

コネクタ

2x SATA 3Gb/s

コネクタ

1x mSATA

コネクタ

AHCI

のサポート


10/ 100/ 1000 Mb/s

オートネゴーシエーション、半

/

全二重通信

ALC892

7.1

チャンネル

,

ハイデフィニションオーディオ

, Biostar Hi-Fi

INTEL® B85:

4x USB 3.0

ポート

(

後部

I/O

に

2

つ及

び内蔵ヘッダー経由に

2

つ

)

8x USB 2.0

ポート

(

後部

I/O

び内蔵ヘッダー経由に

4

つ

)

に

4

つ及

INTEL® H81:

2x USB 3.0

ポート

(

後部

I/O

に

2

つ

)

8x USB 2.0

ポート

(

後部

I/O

に

4

つ及び内

蔵ヘッダー経由に

4

つ

)

拡張スロット

後部

I/O

内蔵

I/O

1x PCIe 3.0 x16

スロット

(x16), Hi-Fi B85N 3D

1x PCIe 2.0 x16

スロット

(x16), Hi-Fi H81N 3D

1x PS/2

マウス

/

キーボード

1x HDMI

ポート

1x VGA

ポート

1x DVI

ポート

2x LAN

ポート

4x USB 2.0

ポート

2x USB 3.0

ポート

5x

オーディオジャック

1x S/PDIF

アウトコネクタ

Hi-Fi B85N 3D

2x SATA 6.0Gb/s

コネクタ

2x SATA 3.0Gb/s

コネクタ

1x mSATA

コネクタ

2x USB 2.0

ヘッダー

(

各ヘッダーは、

2

つの

USB 2.0

ポートを

サポートしています

)

1x USB 3.0

ヘッダー

(

各ヘッダーは、

2

つの

USB 3.0

ポートを

Hi-Fi H81N 3D

1x SATA 6.0Gb/s

コネクタ

2x SATA 3.0Gb/s

コネクタ

1x mSATA

コネクタ

2x USB 2.0

ヘッダー

(

各ヘッダーは、つの

USB 2.0

ポートをサポ

ートしています

)

1x 4-Pin

パワーコネクタ

1x 24-Pin


44


仕様

サポートしています

)

1x 4-Pin


1x 24-Pin


1x CPU

ファンコネクタ

1x

システムファンコネクタ

1x

フロントパネルヘッダー

1x

フロントオーディオヘッダー

1x

クリア

CMOS

ヘッダー

1x

シリアルポートヘッダー

1x

プリンターポートヘッダー

1x

シャーシスピーカーヘッダー

1x CPU

ファンコネクタ

1x

システムファンコネクタ

1x

フロントパネルヘッダー

1x

フロントオーディオヘッダー

1x

クリア

CMOS

ヘッダー

1x

シリアルポートヘッダー

1x

プリンターポートヘッダー

1x

シャーシスピーカーヘッダー

フォームファクタ

ATX

ファクタ、

170 mm x 170 mm

サポート

OS

Windows 7/ 8

Biostar

には、通知なしでサポート

OS

を変更する権限があります。

45


Polish

Obs ł uga procesora

Rodzaj p ł yty

Pami ęć

Przechowywanie

LAN

Codec Audio

USB

Specyfikacje techniczne

Gniazdo procesora (Socket) 1150 dla procesorów Intel® Core i7 / i5 / i3 / Pentium /

Celeron

Moc Wydzielanego Ciep ł a (TDP - Thermal Design Power): 95Watt

* Prosz ę sprawdzi ć list ę obs ł ugiwanych procesorów na stronie internetowej www.biostar.com.tw


Obs ł uga pami ę ci DDR3 1066/ 1333/ 1600 Dwukana ł owa

2 x DDR3 DIMM Pami ęć Gniazda procesora (Slot), Maksymalna wielko ść pami ę ci 16 GB

Ka ż dy DIMM obs ł uguje jeden modu ł non-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3

* Prosz ę sprawdzi ć list ę obs ł ugiwanych pami ęć na stronie internetowej www.biostar.com.tw

INTEL® B85:

Z łą cze 2x SATA 6Gb/s


Z łą cze 1x mSATA

Obs ł uga AHCI

INTEL® H81:



Z łą cze 1x mSATA

Obs ł uga AHCI

2x Uk ł ad RTL 8111G

10/ 100/ 1000 Mb auto negocjacja, pojemno ść dupleks Po ł owe / Pe ł ny

ALC892

Kana ł y Audio wysokiej Definicji 7.1, Biostar Hi-Fi

INTEL® B85:

4 x z łą cza USB 3.0 (2 przez tylne porty wej ś cia/ wyj ś cia oraz 2 przez wewn ę trzne porty)


INTEL® H81:

2 x z łą cza USB 3.0 (2 przez tylne porty wej ś cia/ wyj ś cia)


Z łą cza rozszerze ń

Tylne porty wej ś cia/ wyj ś cia z łą cza 1x PCIe 3.0 x16 (Slot) (x16), Hi-Fi B85N 3D z łą cza 1x PCIe 2.0 x16 (Slot) (x16), Hi-Fi H81N 3D

Klawiatura/Myszka 1x PS/2

Port 1x HDMI (gniazdo)

Port 1x VGA

Port 1x DVI

Port 2x LAN

Porty 4x USB 2.0

Porty 2x USB 3.0

Porty audio 5x

Port zewn ę trzny S/PDIF x1

46

Wewn ę trzne porty wej ś cia/ wyj ś cia

Obudowa

Obs ł uga OS


Specyfikacje techniczne

Hi-Fi B85N 3D

Z łą cza 2x SATA 6.0Gb/s


Z łą cze 1x mSATA

Z łą cza 2x USB 2.0

(ka ż de z łą cze obs ł uguje dodatkowe 2 porty USB 2.0)

Z

(ka porty USB 3.0)

Z

Z

Z

Z

Z łą łą łą łą łą łą cze 1x USB 3.0 ż de z łą cze obs ł uguje dodatkowe 2 cza 4 pionowe x 1 cza 24 pionowe x 1 cze wentylatora CPU x 1 cze wentylatora obudowy x 1 cze przedniego panelu x1

Hi-Fi H81N 3D



Z łą cze 1x mSATA

Z łą cza 2x USB 2.0

(ka ż de z łą cze obs ł uguje dodatkowe 2 porty

USB 2.0)

Z łą cza 4 pionowe x 1

Z łą cza 24 pionowe x 1

Z łą cze wentylatora CPU x 1

Z łą cze wentylatora obudowy x 1

Z łą cze przedniego panelu x1

Z łą cze audio przedniego panelu x1

Z łą cze bezpo ś rednie CMOS x1

Port szeregowy x1

Z łą cze port drukarki x1 z łą cze g ł o ś ników Podwozie x1

Z łą cze audio przedniego panelu x1

Z łą cze bezpo ś rednie CMOS x1

Port szeregowy x1

Z łą cze port drukarki x1 z łą cze g ł o ś ników Podwozie x1

Obudowa ATX, 170 mm x 170 mm

Windows 7/ 8

Biostar zastrzega sobie prawo do dodania lub wycofania obs ł ugi dla OS, z wypowiedzeniem lub bez wypowiedzenia.

47


Portuguese

Suporte

Processador

Tipo Placa Mãe

Memória

Armazenamento

LAN

Codec de Audio

USB

Especificações

Porta 1150 para processador Intel® Core i7 / i5 / i3 / Pentium / Celeron

Alimentação de Design Térmico (TDP – Thermal Design Power): 95Watt

* Por favor consulte www.biostar.com.tw

para obter uma lista de suporte do processador.


Suporta DDR3 1066/ 1333/ 1600 Canal Duplo

2 x DDR3 DIMM Slot de memória Suporta até 16 GB Memória

Cada DIMM suporta non-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3 módulo

* Por favor consulte www.biostar.com.tw

para obter uma lista de suporte do memória.

INTEL® B85:

Conector 2x SATA 6Gb/s


Conector 1x mSATA

Suporta AHCI


INTEL® H81:



Conector 1x mSATA

Suporta AHCI

10/ 100/ 1000 Mb auto negociação, capacidade duplex Metade / Cheio

ALC892

Canais de Áudio de Alta Definição 7.1, Biostar Hi-Fi

INTEL® B85:

Porta 4x USB 3.0 (2 nas entradas/saídas traseiras e 2 pelos Dispositivos internos)


INTEL® H81:

Porta 2x USB 3.0 (2 nas entradas/saídas traseiras)


Slots de expansão

Porta 1x PCIe 3.0 x16 (x16), Hi-Fi B85N 3D

Porta 1x PCIe 2.0 x16 (x16), Hi-Fi H81N 3D

Entradas/Saídas no painel traseiro

Teclado/Mouse 1x PS/2

Porta 1x HDMI

Porta 1x VGA

Porta 1x DVI

Porta 2x LAN

Porta 4x USB 2.0

Porta 2x USB 3.0

Soquete audio 5x

Conector Externo S/PDIF 1x

48

Conectores na placa

Fator de Fôrma

Suporte OS


Especificações

Hi-Fi B85N 3D

Conector 2x SATA 6.0Gb/s


Conector 1x mSATA

Dispositivo 2x USB 2.0 (cada Dispositivo suporta 2 portas USB 2.0)

Dispositivo 1x USB 3.0 (cada Dispositivo

Hi-Fi H81N 3D



Conector 1x mSATA

Dispositivo 2x USB 2.0 (cada Dispositivo suporta 2 portas USB 2.0)

Conector de 4 pinos x1 suporta 2 portas USB 3.0)

Conector de 4 pinos x1


Conector de Ventoinha processador x1

Conector de Ventoinha Sistema x1

Dispositivo Painel Frontal x1

Dispositivo de Audio Frontal x1

Dispositivo CMOS Direct x1


Conector de Ventoinha processador x1

Conector de Ventoinha Sistema x1

Dispositivo Painel Frontal x1

Dispositivo de Audio Frontal x1

Dispositivo CMOS Direct x1

Dispositivo Porta Série x1

Dispositivo Porta Impressora x1

Chassis Speaker Header x1 Dispositivo Porta Série x1

Dispositivo Porta Impressora x1

Chassis Speaker Header x1

Fator de Fôrma ATX, 170 mm x 170 mm

Windows 7/ 8

Biostar reserva seu direito de adicionar ou retirar o suporte para qualquer OS com ou sem notificação.

49


Russian

Спецификации

Поддержка центрального процессора

Сокет для

Максимальный

*

1150

Перечень процессоров термопакет поддержки центрального центрального

Набор микросхем INTEL® B85 (Hi-Fi B85N 3D)

Intel® Core i7 / i5 / i3 / Pentium / Celeron процессора процессора

(TDP): 95 смотрите на ватт www.biostar.com.tw

INTEL® H81 (Hi-Fi H81N 3D)

.

Память

USB

Накопитель

Локальная

Аудиокодек сеть

Поддерживает двухканальный 1066/ 1333/ 1600

2 гнезда платы памяти DDR3 DIMM, максимальная память до 16 Гб

Каждый модуль DIMM поддерживает модуль не -ECC 512 Мб / 1/ 2/ 4/ 8 Гб DDR3

* Перечень поддержки памяти смотрите на www.biostar.com.tw

.

INTEL® B85:

Соединитель



2x SATA 6

2x SATA 3

1x mSATA

Гб

Гб

/

/ с с

INTEL® H81:

Соединитель 1x SATA 6 Гб / с


Соединитель 1x mSATA

Поддерживает AHCI Поддерживает AHCI


Автосогласование 10/ 100/ 1000 Мб / с , работает в полно / полудуплексном режиме

ALC892

Каналы 7.1, высококачественное аудио , Biostar Hi-Fi

INTEL® B85:

4 порта USB 3.0 (2 сзади ввода вывода и

2 через внутренние контакты )

8 порта USB 2.0 (4 сзади ввода вывода и

4 через внутренние контакты )

INTEL® H81:

2 порта USB 3.0 (2 сзади ввода вывода )

8 порта USB 2.0 (4 сзади ввода вывода и 4 через внутренние контакты )

Гнезда расшир .

Задняя плата ввода вывода

Внутр . Плата ввода вывода

1x PCIe 3.0 x16 гнездо (x16), Hi-Fi B85N 3D

1x PCIe 2.0 x16 гнездо (x16), Hi-Fi H81N 3D

1 мышь / клавиатура PS/2

1 порт HDMI

1 порт VGA

1 порт DVI

2 порт локальной сети

4 порта USB 2.0

2 порта USB 3.0

5 гнезд для подключения наушников

1 соединитель S/PDIF-Out

Hi-Fi B85N 3D




2 контакта USB 2.0 ( каждый контакт поддерживает 2 порта USB 2.0)

1 контакт USB 3.0 ( каждый контакт

Hi-Fi H81N 3D




2 контакта USB 2.0 ( каждый контакт поддерживает 2 порта USB 2.0)

1 4выводный разъем питания

50

Конструктив

Поддержка ОС


Спецификации

поддерживает 2 порта USB 3.0)



1 разъем вентилятора ЦП

1 разъема вентилятора системы

1 контакт передней панели

1 контакт передней аудиопанели

1 контакт микросхемы Clear CMOS

1 контакт последовательного порта

1 контакт порта принтера

1 Шасси спикер заголовка

Форм фактор ATX, 170 мм x 170 мм

1 24-

1

1

1

1

1

1

1

1 выводный разъем разъема контакт контакт контакт контакт контакт

Шасси вентилятора вентилятора передней передней микросхемы порта спикер разъем питания

ЦП панели аудиопанели принтера заголовка системы

Clear CMOS последовательного порта

Windows 7/ 8

Biostar оставляет за собой право добавлять или удалять поддержку любой ОС , с уведомлением или без .

51


Spanish

Compatibilidad con el procesador

Tipo de Placa

Memoria

Almacenamiento de información

LAN

Códec Audio

USB

Ranuras de

Extinción

Panel trasero de

E/S

Especificaciones

Ranura 1150 para procesador Intel® Core i7 / i5 / i3 / Pentium / Celeron

Alimentación de Proyección Térmica (TDP – Thermal Design Power): 95Watt

*Por favor consultar con www.biostar.com.tw

para la lista de compatibilidad con el procesador.


Soporta DDR3 1066/ 1333/ 1600 Doble Canal

2x DDR3 DIMM Ranura de memoria Soporta hasta 16 GB Memoria

Cada DIMM soporta un modulo non-ECC 512MB/ 1/ 2/ 4/ 8 GB DDR3

*Por favor consultar con www.biostar.com.tw

para la lista de compatibilidad con el memoria.

INTEL® B85:



Conector 1x mSATA

Soporta AHCI

INTEL® H81:



Conector 1x mSATA

Soporta AHCI


10/ 100/ 1000 Mb/s auto negociación, capacidad dúplex Mitad/Completo

ALC892

Canales Audio de Alta Definición 7.1, Biostar Hi-Fi

INTEL® B85:

Ranura 4x USB 3.0 (2 en las entrada/salidas posteriores y 2 por los distribuidores internos)


INTEL® H81:

Ranura 2x USB 3.0 (2 en las entrada/salidas posteriores)


Ranura 1x PCIe 3.0 x16 (x16), Hi-Fi B85N 3D

Ranura 1x PCIe 2.0 x16 (x16), Hi-Fi H81N 3D

Teclado/Ratón 1x PS/2

Ranura 1x HDMI

Ranura 1x VGA

Ranura 1x DVI

Ranura 2x LAN

Ranura 4x USB 2.0

Ranura 2x USB 3.0

Socket audio 5x

Conector Externo S/PDIF x1

52

Conectores en placa

Factor de Forma

Soporte OS


Especificaciones

Hi-Fi B85N 3D

Conector 2x SATA 6Gb’s


Conector 1x mSATA

Distribuidor 2x USB 2.0 (cada distribuidor soporta 2 ranuras USB 2.0)

Distribuidor 1x USB 3.0 (cada distribuidor

Hi-Fi H81N 3D



Conector 1x mSATA

Distribuidor 2x USB 2.0 (cada distribuidor soporta 2 ranuras USB 2.0)

Conector con 4 patillas x1 soporta 2 ranuras USB 3.0)

Conector con 4 patillas x1


Conector Ventilador procesador x1

Conector Ventilador Sistema x1

Distribuidor Panel Frontal x1

Distribuidor Audio Frontal x1

Distribuidor CMOS Directo x1


Conector Ventilador procesador x1

Conector Ventilador Sistema x1

Distribuidor Panel Frontal x1

Distribuidor Audio Frontal x1

Distribuidor CMOS Directo x1

Distribuidor Ranura Serie x1

Distribuidor Ranura Impresora x1

Cabezal del altavoz del chasis x1 Distribuidor Ranura Serie x1

Distribuidor Ranura Impresora x1

Cabezal del altavoz del chasis x1

Factor de Forma ATX, 170 mm x 170 mm

Windows 7/ 8

Biostar reserva su derecho de añadir o retirar el soporte para cada OS con o sin notificación.

2013/12/19

53

Biostar Hi-Fi B85N 3D Ver. 5.x User's manual

Hi-Fi B85N 3D/ Hi-Fi H81N 3D Setup Manual

FCC Information and Copyright

Table of Contents

CHAPTER 1: INTRODUCTION

1.1 Before You Start

1.4 Rear Panel Connectors

CHAPTER 2: HARDWARE INSTALLATION

2.1 Install Central Processing Unit (CPU)

CPU_FAN1: CPU Fan Header

SYS_FAN1: System Fan Header

DDR3 Modules

Memory Capacity

Dual Channel Memory Installation

Install an Expansion Card

PEX16_1: PCI-Express Gen3 x16 Slot (Hi-Fi B85N 3D)

PEX16_1: PCI-Express Gen2 x16 Slot (Hi-Fi H81N 3D)

JCMOS1: Clear CMOS Jumper

Clear CMOS Procedures:

JMPCI_TYP1: mSATA connector mode jumper

2.7 Headers & Connectors

ATXPWR1: ATX Power Source Connector

ATXPWR2: ATX Power Source Connector

JPANEL1: Front Panel Header

JSPKR1: Chassis Speaker Header

MSATA1: mSATA Connector (mPCIe Connector)

SATA1-4: Serial ATA Connectors

JFRONT_USB3_1: Header for USB 3.0 Ports at Front Panel

F_USB1/2: Header for USB 2.0 Ports at Front Panel

F_AUDIO1: Front Panel Audio Header

COM: Serial Port Header

CHAPTER 3: UEFI BIOS & SOFTWARE

3.1 UEFI BIOS Setup

BIOSTAR BIOS Flasher

BIOS Update Utility (through the Internet)

BIOS Update Utility (through a BIOS file)

3.3 Software

Installing Software

Launching Software

BIOScreen Utility

eHot-Line

Smart EAR 3D

Smart Connect Technology

System Requirement:

Configuring Intel Smart Connect Technology

Basic and advanced settings

Rapid Start Technology

System Requirement:

Installing Intel® RST:

Intel® Small Business Advantage

Software Monitor

Data Backup and Restore

USB Blocker

PC Health Center

Energy Saver

Supported Operating Systems:

Installing Intel SBA

CHAPTER 4: USEFUL HELP

A. Driver Installation

B. Software Installation

C. Manual

4.2 AMI BIOS Beep Code

Boot Block Beep Codes

POST BIOS Beep Codes

4.3 Troubleshooting

CPU Overheated

APPENDIX: Specifications in Other Languages

Arabic

French

German

Italian

Japanese

Polish

Portuguese

Russian

Spanish

Related manuals

Biostar

H81MHP Ver. 6.x

Biostar