Dell™ P1913/P1913S/P2213 Monitor
User's Guide
Setting the display resolution
Information in this document is subject to change without notice.
© 2012 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; Microsoft and Windows are either trademarks or registered trademarks of Microsoft Corporation in the United
States and/or other countries, Intel is a registered trademark of Intel Corporation in the U.S. and other countries; and ATI is a trademark of Advanced Micro Devices, Inc. ENERGY STAR is a
registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in
trademarks and trade names other than its own.
Model P1913b/P1913t/P1913Sb/P1913Sf/P2213f/P2213t
May 2012 Rev. A01
Dell™ P1913/P1913S/P2213 Monitor User's Guide
About Your Monitor
Setting Up the Monitor
Operating the Monitor
Troubleshooting
Appendix
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
Information in this document is subject to change without notice.
© 2012 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc; Microsoft and Windows are either trademarks or registered trademarks of Microsoft Corporation in the United
States and/or other countries, Intel is a registered trademark of Intel Corporation in the U.S. and other countries; and ATI is a trademark of Advanced Micro Devices, Inc. ENERGY STAR is a
registered trademark of the U.S. Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in
trademarks and trade names other than its own.
Model P1913b/P1913t/P1913Sb/P1913Sf/P2213f/P2213t
May 2012 Rev. A01
Back to Contents Page
About Your Monitor
Dell™ P1913/P1913S/P2213 Monitor User's Guide
Package Contents
Product Features
Identifying Parts and Controls
Monitor Specifications
Plug and Play Capability
Universal Serial Bus (USB) Interface
LCD Monitor Quality and Pixel Policy
Maintenance Guidelines
Package Contents
Your monitor ships with the components shown below. Ensure that you have received all the components and contact Dell if something is missing.
NOTE: Some items may be optional and may not ship with your monitor. Some features or media may not be available in certain countries.
NOTE: To set up with any other stand, please refer to the respective stand setup guide for setup instructions.
NOTE: P1913/P1913S/P2213 monitor is BFR/PVC-free (Halogen-free) excluding external cables.
Monitor
Stand
Power Cable
VGA Cable (Attached to the monitor)
DVI Cable
USB upstream cable (enables the USB ports on the monitor)
Drivers and Documentation media
Quick Setup Guide
Product and Safety Information Guide
Product Features
The Dell Professional P1913/P1913S/P2213 flat panel display has an active matrix, Thin-Film Transistor (TFT), Liquid Crystal Display (LCD) and LED backlight. The monitor
features include:
¦ P1913: 48.26 cm (19-inch) viewable area display (measured diagonally). 1440 x 900 resolution, plus full-screen support for lower resolutions.
¦ P1913S: 48.26 cm (19-inch) viewable area display (measured diagonally). 1280 x 1024 resolution, plus full-screen support for lower resolutions.
¦ P2213: 55.88 cm (22-inch) viewable area display (measured diagonally). 1680 x 1050 resolution, plus full-screen support for lower resolutions.
¦ Wide viewing angle to allow viewing from a sitting or standing position, or while moving from side-to-side.
¦ Tilt, swivel, vertical extension and rotate adjustment capability.
¦ Removable stand and Video Electronics Standards Association (VESA ™) 100 mm mounting holes for flexible mounting solutions.
¦ Plug and play capability if supported by your system.
¦ On-Screen Display (OSD) adjustments for ease of set-up and screen optimization.
¦ Software and documentation media includes an Information File (INF), Image Color Matching File (ICM), Dell Display Manager software application and product documentation.
¦ Energy Saver feature for Energy Star compliance.
¦ Security lock slot.
¦ Stand lock.
¦ Asset Management Capability.
¦ Capability to switch from wide aspect to standard aspect ratio while maintaining the image quality.
¦ EPEAT Gold Rating.
¦ P1913/P1913S/P2213 monitor is BFR/PVC-free (Halogen-free) excluding external cables.
¦ TCO-Certified Displays.
¦ Dell Display Manager software included (comes in the CD shipped with the monitor).
¦ Arsenic-Free glass and Mercury-Free for the panel only.
¦ High Dynamic Contrast Ratio (2,000,000:1).
¦ 0.3 W standby power when in the sleep mode.
¦ Energy Gauge shows the energy level being consumed by the monitor in real time.
Identifying Parts and Controls
Front View
Front panel controls
Label
Description
1
Function buttons (For more information, see Operating the
Monitor)
2
Power On/Off button (with LED indicator)
Back View
Back View with monitor stand
Label
Description
Use
1
VESA mounting holes (100 mm x 100 mm
- behind attached VESA Plate)
Wall mount monitor using VESA-compatible wall mount kit (100 mm x 100 mm).
2
Regulatory label
Lists the regulatory approvals.
3
Stand release button
Release stand from monitor.
4
Barcode serial number label
Refer to this label if you need to contact Dell for technical support.
5
Security lock slot
Secures monitor with security cable lock.
6
Dell Soundbar mounting brackets
Attaches the optional Dell Soundbar.
7
Cable management slot
Use to organize cables by placing them through the slot.
Side View
Bottom View
Bottom view without monitor stand
Label
Description
Use
1
AC power cord connector
Connect the power cable.
2
DC power connector for Dell Soundbar
Connect the power cord for the soundbar (optional).
3
DP connector
Connect your computer DP cable.
4
VGA connector
Connect your computer VGA cable.
5
DVI connector
Connect your computer DVI cable.
6
USB upstream port
Connect the USB cable that came with your monitor to the monitor and the
computer. Once this cable is connected, you can use the USB connectors on
the monitor.
7
USB downstream port
Connect your USB device. You can only use this connector after you have
connected the USB cable to the computer and USB upstream connector on the
monitor.
8
Stand lock feature
To lock the stand to the monitor using a M3 x 6 mm screw (the screw is not
provided).
Monitor Specifications
Flat Panel Specifications
Model
P1913
P1913S
P2213
Screen type
Active matrix - TFT LCD
Active matrix - TFT LCD
Active matrix - TFT LCD
Panel type
TN
TN
TN
Screen dimensions
482.6 mm (19-inches diagonal viewable image 482.6 mm (19-inches diagonal viewable image
size)
size)
558.8 mm (22-inches diagonal viewable image
size)
408.2 mm (16.07 inches)
376.3 mm (14.81 inches)
473.8 mm (18.65 inches)
255.2 mm (10.05 inches)
301.1 mm (11.85 inches)
296.1 mm (11.66 inches)
0.2835 mm
0.294 mm
0.282 mm
160° (vertical) typical
160° (vertical) typical
160° (vertical) typical
170° (horizontal) typical
170° (horizontal) typical
170° (horizontal) typical
250 cd/m² (typical)
250 cd/m² (typical)
250 cd/m² (typical)
1000 to 1 (typical)
1000 to 1 (typical)
1000 to 1 (typical)
2M to 1 (typical Dynamic Contrast On)
2M to 1 (typical Dynamic Contrast On)
2M to 1 (typical Dynamic Contrast On)
Faceplate coating
Antiglare with hard-coating 3H
Antiglare with hard-coating 3H
Antiglare with hard-coating 3H
Backlight
LED edgelight system
LED edgelight system
LED edgelight system
Response time
5 ms black to white (typical)
5 ms black to white (typical)
5 ms black to white (typical)
Color depth
16.7 million colors
16.7 million colors
16.7 million colors
Color gamut
83%*
83%*
83%*
Preset display area:
Horizontal
Vertical
Pixel pitch
Viewing angle
Luminance output
Contrast ratio
*[P1913]/[P1913S]/[P2213] color gamut (typical) is based on CIE1976 (83%) and CIE1931 (72%) test standards.
Resolution Specifications
Model
P1913
P1913S
Horizontal scan range
30 kHz to 81 kHz (automatic)
30 kHz to 83 kHz (automatic)
Vertical scan range
56 Hz to 76 Hz (automatic)
56 Hz to 75 Hz (automatic)
Maximum preset resolution
1440 x 900 at 60 Hz
1280 x 1024 at 60 Hz
P2213
1680 x 1050 at 60 Hz
Supported Video Modes
Model
P1913/P1913S/P2213
Video display capabilities (DVI & DP playback)
480p, 480i, 576p, 576i, 720p, 1080p, 1080i
Preset Display Modes
P1913
Display Mode
Horizontal Frequency
(kHz)
Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (Horizontal/Vertical)
VESA, 720 x 400
31.5
70.0
28.3
-/+
VESA, 640 x 480
31.5
60.0
25.2
-/-
VESA, 640 x 480
37.5
75.0
31.5
-/-
VESA, 800 x 600
37.9
60.3
40.0
+/+
VESA, 800 x 600
46.9
75.0
49.5
+/+
VESA, 1024 x 768
60.0
75.0
78.8
+/+
VESA, 1152 x 864
67.5
75.0
108.0
+/+
VESA, 1280 x 800
49.3
59.9
71.0
+/-
VESA, 1280 x 1024
64.0
60.0
108.0
+/+
VESA, 1280 x 1024
80.0
75.0
135.0
+/+
VESA, 1440 x 900
55.5
60.0
106.5
-/+
VESA, 1440 x 900
70.6
75.0
136.8
-/+
P1913S
Display Mode
Horizontal Frequency
(kHz)
Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (Horizontal/Vertical)
VESA, 720 x 400
31.5
70.0
28.3
-/+
VESA, 640 x 480
31.5
60.0
25.2
-/-
VESA, 640 x 480
37.5
75.0
31.5
-/-
VESA, 800 x 600
37.9
60.3
40.0
+/+
VESA, 800 x 600
46.9
75.0
49.5
+/+
VESA, 1024 x 768
48.4
60.0
65.0
-/-
VESA, 1024 x 768
60.0
75.0
78.8
+/+
VESA, 1152 x 864
67.5
75.0
108.0
+/+
VESA, 1280 x 1024
64.0
60.0
108.0
+/+
VESA, 1280 x 1024
80.0
75.0
135.0
+/+
P2213
Display Mode
Horizontal Frequency
(kHz)
Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (Horizontal/Vertical)
VESA, 720 x 400
31.5
70.0
28.3
-/+
VESA, 640 x 480
31.5
60.0
25.2
-/-
VESA, 640 x 480
37.5
75.0
31.5
-/-
VESA, 800 x 600
37.9
60.0
40.0
+/+
VESA, 800 x 600
46.9
75.0
49.5
+/+
VESA, 1024 x 768
48.4
60.0
65.0
-/-
VESA, 1024 x 768
60.0
75.0
78.8
+/+
VESA, 1152 x 864
67.5
75.0
108.0
+/+
VESA, 1280 x 1024
64.0
60.0
108.0
+/+
VESA, 1280 x 1024
80.0
75.0
135.0
+/+
VESA, 1680 x 1050
65.2
60.0
146.0
-/+
VESA, 1680 x 1050
82.3
75.0
187.0
-/+
Electrical Specifications
Model
P1913/P1913S/P2213
Analog RGB, 0.7 Volts +/- 5%, positive polarity at 75 ohm input impedance
Digital DVI-D TMDS, 600 mV for each differential line, positive polarity at 50 ohm input
impedance
DP 1.2 signal input support*
Video input signals
Synchronization input signals
Separate horizontal and vertical synchronizations, polarity-free TTL level, SOG (Composite
SYNC on green)
AC input voltage/frequency/current
100 VAC to 240 VAC / 50 Hz or 60 Hz + 3 Hz / 1.5 A (typical)
120 V : 30 A (Max)
240 V : 60 A (Max)
Inrush current
*Support DP1.2 (CORE) specification. Excludes High Bit Rate 2 (HBR2), Fast AUX transaction, Multi-stream transport (MST), 3D stereo transport , HBR Audio (or high data rate
audio)
Physical Characteristics
Model
P1913
P1913S
P2213
Connector type
15-pin D-subminiature, blue
connector; DVI-D, white connector;
DP, black connector
15-pin D-subminiature, blue
connector; DVI-D, white connector;
DP, black connector
15-pin D-subminiature, blue
connector; DVI-D, white connector;
DP, black connector
Signal cable
type
Digital: detachable, DVI-D,
solid pins, shipped detached
from the monitor
Digital: DisplayPort, 20pin
Analog: attachable, D-Sub,
15 pins, shipped attached to
the monitor
Digital: detachable, DVI-D,
solid pins, shipped detached
from the monitor
Digital: DisplayPort, 20pin
Analog: attachable, D-Sub,
15 pins, shipped attached to
the monitor
Digital: detachable, DVI-D,
solid pins, shipped detached
from the monitor
Digital: DisplayPort, 20pin
Analog: attachable, D-Sub,
15 pins, shipped attached to
the monitor
Dimensions (with stand)
Height
(extended)
476.4 mm ( 18.76 inches)
500.1 mm (19.69 inches)
497.4 mm (19.58 inches)
Height
(compressed)
356.9 mm (14.05 inches)
370.1 mm (14.57 inches)
368.9 mm (14.52 inches)
Width
443.8 mm (17.47 inches)
411.9 mm (16.22 inches)
510.4 mm (20.09 inches)
Depth
183.3 mm (7.22 inches)
183.3 mm (7.22 inches)
183.3 mm (7.22 inches)
Dimensions (without stand)
Height
290.8 mm (11.45 inches)
336.7 mm (13.26 inches)
332.7 mm (13.10 inches)
Width
443.8 mm (17.47 inches)
411.9 mm (16.22 inches)
510.4 mm (20.09 inches)
Depth
58.5 mm (2.30 inches)
59.3 mm (2.33 inches)
59.8 mm (2.35 inches)
Stand dimensions
Height
(extended)
401.2 mm (15.80 inches)
401.2 mm (15.80 inches)
401.2 mm (15.80 inches)
Height
(compressed)
356.9 mm (14.05 inches)
356.9 mm (14.05 inches)
356.9 mm (14.05 inches)
Width
265.8 mm (10.46 inches)
265.8 mm (10.46 inches)
265.8 mm (10.46 inches)
Depth
183.3 mm (7.22 inches)
183.3 mm (7.22 inches)
183.3 mm (7.22 inches)
Weight with
packaging
5.87 kg (12.91 lb)
6.75 kg (14.85 lb)
7.43 kg (16.35 lb)
Weight with
stand assembly
and cables
4.75 kg (10.45 lb)
5.23 kg (11.51 lb)
5.71 kg (12.56 lb)
Weight without
stand assembly
(For wall mount
or VESA mount
considerations no cables)
2.52 kg (5.54 lb)
2.95 kg (6.49 lb)
3.43 kg (7.55 lb)
Weight of stand
assembly
1.73 kg (3.81 lb)
2.00 kg (4.40 lb)
1.73 kg (3.81 lb)
Weight
Front frame gloss
Black Frame - 5.0 gloss unit (max.)
Silver Frame - 20.0 gloss unit (max.)
Environmental Characteristics
Model
P1913
P1913S
Temperature
Operating
Non-operating
0 °C to 40 °C
Storage: -20 °C to 60 °C (-4 °F to 140 °F)
Shipping: -20 °C to 60 °C (-4 °F to 140 °F)
Humidity
Operating
Non-operating
Altitude
10% to 80% (non-condensing)
Storage: 5% to 90% (non-condensing)
Shipping: 5% to 90% (non-condensing)
P2213
Operating
3,048 m (10,000 ft) max
Non-operating
10,668 m (35,000 ft) max
10,668 m (35,000 ft) max
143.31 BTU/hour
(maximum)
58.01 BTU/hour
(typical)
Thermal dissipation
143.31 BTU/hour
(maximum)
58.01 BTU/hour
(typical)
10,668 m (35,000 ft) max
153.59 BTU/hour
(maximum)
85.33 BTU/hour
(typical)
Power Management Modes
If you have VESA's DPM™ compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. This is referred to
as Power Save Mode*. If the computer detects input from the keyboard, mouse, or other input devices, the monitor automatically resumes functioning. The following table shows
the power consumption and signaling of this automatic power saving feature:
VESA
Modes
Normal
operation
Active-off
mode
Switch off
Horizontal
Sync
Active
Inactive
-
Vertical
Sync
Active
Inactive
-
Video
Active
Power
Indicator
Blue
Blanked
Amber
Less than 0.3 W
Less than 0.3 W
Less than 0.3 W
Off
Less than 0.3 W
Less than 0.3 W
Less than 0.3 W
-
P1913
42 W (maximum) **
17 W (typical)
Power Consumption
P1913S
P2213
42 W (maximum) ** 45 W (maximum) **
17 W (typical)
25 W (typical)
The OSD functions only in the normal operation mode. When any button is pressed in the Active-off mode, one of the following messages will be displayed:
Activate the computer and the monitor to gain access to the OSD.
NOTE: This monitor is ENERGY STAR ®-compliant.
* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.
** Maximum power consumption with max luminance, Dell Soundbar, and USB active.
Pin Assignments
VGA Connector
Pin
15-pin Side of the Connected Signal Cable
Number
1
Video-Red
2
Video-Green
3
Video-Blue
4
GND
5
Self-test
6
GND-R
7
GND-G
8
GND-B
9
Computer 5 V/3.3 V
10
GND-sync
11
GND
12
DDC data
13
H-sync
14
V-sync
15
DDC clock
DVI Connector
Pin
Number
24-pin Side of the Connected Signal Cable
1
TMDS RX2-
2
TMDS RX2+
3
TMDS Ground
4
Floating
5
Floating
6
DDC Clock
7
DDC Data
8
Floating
9
TMDS RX1-
10
TMDS RX1+
11
TMDS Ground
12
Floating
13
Floating
14
+5 V/+3.3 V power
15
Self test
16
Hot Plug Detect
17
TMDS RX0-
18
TMDS RX0+
19
TMDS Ground
20
Floating
21
Floating
22
TMDS Ground
23
TMDS Clock+
24
TMDS Clock-
DisplayPort Connector
Pin Number
20-pin Side of the Connected
Signal Cable
1
ML0(p)
2
GND
3
ML0(n)
4
ML1(p)
5
GND
6
ML1(n)
7
ML2(p)
8
GND
9
ML2(n)
10
ML3(p)
11
GND
12
ML3(n)
13
GND
14
GND
15
AUX(p)
16
GND
17
AUX(n)
18
HPD
19
Re-PWR
20
PWR
Plug and Play Capability
You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display Identification Data (EDID)
using Display Data Channel (DDC) protocols so the system can configure itself and optimize the monitor settings. Most monitor installations are automatic; you can select different
settings if desired. For more information about changing the monitor settings, see Operating the Monitor.
Universal Serial Bus (USB) Interface
This section gives you information about the USB ports that are available on the monitor.
NOTE: This monitor supports High-Speed Certified USB 2.0 interface.
Transfer Speed
Data
Rate
Power Consumption
High speed
480 Mbps
2.5 W (Max, each port)
Full speed
12 Mbps
2.5 W (Max, each port)
Low speed
1.5 Mbps
2.5 W (Max, each port)
USB Upstream Connector
Pin Number
4-pin Side of the Connector
1
DMU
2
VCC
3
DPU
4
GND
USB Downstream Connector
Pin Number
4-Pin Side of the Signal Cable
1
VCC
2
DMD
3
DPD
4
GND
USB Ports
1 upstream - back
2 downstream - back
NOTE: USB 2.0 functionality requires a USB 2.0-capable computer.
NOTE: The monitor's USB interface works only when the monitor is On or in the power save mode. If you turn Off the monitor and then turn it On, the attached peripherals may
take a few seconds to resume normal functionality.
LCD Monitor Quality and Pixel Policy
During the LCD Monitor manufacturing process, it is not uncommon for one or more pixels to become fixed in an unchanging state which are hard to see and do not affect the
display quality or usability. For more information on Dell Monitor Quality and Pixel Policy, see Dell Support site at: support.dell.com.
Maintenance Guidelines
Cleaning Your Monitor
CAUTION: Read and follow the safety instructions before cleaning the monitor.
WARNING: Before cleaning the monitor, unplug the monitor power cable from the electrical outlet.
For best practices, follow the instructions in the list below while unpacking, cleaning, or handling your monitor:
To clean your anti-static screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the anti-static coating.
Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.
Use a lightly-dampened, warm cloth to clean the monitor. Avoid using detergent of any kind as some detergents leave a milky film on the monitor.
If you notice white powder when you unpack your monitor, wipe it off with a cloth.
Handle your monitor with care as a darker-colored monitor may get scratched and show white scuff marks more than a lighter-colored monitor.
To help maintain the best image quality on your monitor, use a dynamically changing screen saver and turn off your monitor when not in use.
Back to Contents Page
Back to Contents Page
Setting Up the Monitor
Dell™ P1913/P1913S/P2213 Monitor User's Guide
Attaching the Stand
Connecting the Monitor
Organizing Your Cables
Attaching Dell Soundbar AX510/AY511 (Optional)
Removing the Monitor Stand
Wall Mounting (Optional)
Attaching the Stand
NOTE: The stand is detached when the monitor is shipped from the factory.
NOTE: This is applicable for a monitor with a stand. When any other stand is bought, please refer to the respective stand setup guide for the set up instructions.
To attach the monitor stand:
1. Remove the cover and place the monitor on it.
2. Fit the two tabs on the upper part of the stand to the groove on the back of the monitor.
3. Press the stand till it snaps into place.
Connecting Your Monitor
WARNING: Before you begin any of the procedures in this section, follow the Safety Instructions.
To connect your monitor to the computer:
1. Turn off your computer and disconnect the power cable.
Connect the blue (VGA) cable from your monitor to the computer.
NOTE: If your computer supports a white DVI connector, connect the white DVI cable to the monitor and the white DVI connector to
your computer.
NOTE: Do not connect the blue VGA or the white DVI cable to the computer at the same time.
2. Connect the white (digital DVI-D) or the blue (analog VGA) or the black (DisplayPort) display connector cable to the corresponding video port on the back of your
computer. Do not use the three cables on the same computer. Use all cables only when they are connected to three different computers with appropriate video
systems.
Connecting the white DVI cable
Connecting the blue VGA cable
Connecting the black DisplayPort cable
CAUTION: The graphics are used for the purpose of illustration only. Appearance of the computer may vary.
Connecting the USB cable
After you have completed connecting the DVI/VGA cable, follow the procedures below to connect the USB cable to the computer and complete your monitor setup:
Connect the upstream USB port (cable supplied) to an appropriate USB port on your computer. (See bottom view for details.)
Connect the USB peripherals to the downstream USB ports on the monitor.
Plug the power cables for your computer and monitor into a nearby outlet.
Turn on the monitor and the computer.
If your monitor displays an image, installation is complete. If it does not display an image, see Solving Problems.
5. Use the cable slot on the monitor stand to organize the cables.
1.
2.
3.
4.
Organizing Your Cables
After attaching all necessary cables to your monitor and computer, (See Connecting Your Monitor for cable attachment,) organize all cables as shown above.
Attaching Dell Soundbar AX510/AY511 (Optional)
CAUTION: Do not use with any device other than the Dell Soundbar.
NOTE: The Soundbar power connector (+12 V DC output) is for the optional Dell Soundbar only.
To attach the Soundbar:
1.
At the back of the monitor, attach the Soundbar by aligning the two slots with the two tabs along the bottom of the monitor.
2.
Slide the Soundbar to the left until it snaps into place.
3.
Connect the Soundbar with the DC power connector.
4.
Insert the mini stereo plug from the back of the Soundbar into the computer's audio output port.
For HDMI/DP, you can insert the mini stereo plug into the monitor’s audio output port. If there is no sound, check your PC if the Audio output is configured to
HMDI/DP output.
Removing the Monitor Stand
NOTE: To prevent scratches on the LCD screen while removing the stand, ensure that the monitor is placed on a soft, clean surface.
NOTE: This is applicable for a monitor with a stand. When any other stand is bought, please refer to the respective stand setup guide for the set-up instructions.
To remove the stand:
1. Place the monitor on a flat surface.
2. Press and hold the stand release button.
3. Lift the stand up and away from the monitor.
Wall Mounting (Optional)
(Screw dimension: M4 x 10 mm).
Refer to the instructions that come with the VESA-compatible wall mounting kit.
1.
2.
3.
4.
5.
Place the monitor panel on a soft cloth or cushion on a stable, flat table.
Remove the stand.
Use a Philips crosshead screwdriver to remove the four screws securing the plastic cover.
Attach the mounting bracket from the wall mounting kit to the monitor.
Mount the monitor on the wall by following the instructions that comes with the wall mounting kit.
NOTE: For use only with UL-listed wall mount bracket with minimum weight/load bearing capacity of 5.88 kg.
Back to Contents Page
Back to Contents Page
Operating the Monitor
Dell™ P1913/P1913S/P2213 Monitor User's Guide
Power On the Monitor
Using the Front Panel Controls
Using the On-Screen Display (OSD) Menu
Setting the Maximum Resolution
Using Dell Soundbar
Using the Tilt, Swivel, and Vertical Extension
Rotating the Monitor
Adjusting the Rotation Display Settings of Your System
Power On the Monitor
Press the
button to turn on the monitor
Using the Front Panel Controls
Use the control buttons on the front of the monitor to adjust the characteristics of the image being displayed. As you use these buttons to adjust the controls, an OSD shows the numeric values
of the characteristics as they change.
The following table describes the front panel buttons:
Front Panel Button
1
Description
Use this button to choose from a list of preset color modes.
Shortcut
key/Preset
Modes
Use this button to directly access the "Brightness/Contrast" menu.
2
Shortcut key/
Brightness/Contrast
Use the MENU button to launch the On-Screen Display (OSD) and select the OSD Menu. See Accessing the Menu System.
3
Menu
Use this button to go back to the main menu or exit the OSD main menu.
4
Exit
Use the Power button to turn the monitor On and Off.
5
The blue LED indicates the monitor is On and fully functional. An amber LED indicates the power save mode.
Power
(with power light
indicator)
Front Panel Button
Use the buttons on the front of the monitor to adjust the image settings.
Front Panel Button
1
Description
Use the Up button to adjust (increase ranges) items in the OSD menu.
Up
2
Use the Down button to adjust (decrease ranges) items in the OSD menu.
Down
3
Use the OK button to confirm your selection.
OK
Use the Back button to go back to the previous menu.
4
Back
Using the On-Screen Display (OSD) Menu
Accessing the Menu System
NOTE: If you change the settings and then either proceed to another menu or exit the OSD menu, the monitor automatically saves those changes. The changes are also saved if you
change the settings and then wait for the OSD menu to disappear.
1. Press the
button to launch the OSD menu and display the main menu.
Main Menu for analog (VGA) input
or
Main Menu for digital (DVI) input
or
Main Menu for digital (DP) input
NOTE: Auto Adjust is only available when you use the analog (VGA) connector.
NOTE: For P1913, the maximum resolution is 1440 x 900 @ 60Hz. For P1913S, the maximum resolution is 1280 x 1024 @ 60Hz.
2. Press the
and
buttons to move between the setting options. As you move from one icon to another, the option name is highlighted. See the following table for a complete list
of all the options available for the monitor.
3. Press the
button once to activate the highlighted option.
4. Press
and
5. Press
to enter the slide bar and then use the
6. Select the
Icon
button to select the desired parameter.
and
buttons, according to the indicators on the menu, to make your changes.
button to return to the main menu.
Menu and Submenus
Brightness/Contrast
Description
Use this menu to activate Brightness/Contrast adjustment.
Brightness
Brightness adjusts the luminance of the backlight.
Press the
button to increase the brightness and press the
button to decrease the brightness (min 0 / max 100).
NOTE: Manual adjustment of Brightness is disabled when Energy Smart or Dynamic Contrast is switched On.
Contrast
Adjust the Brightness first, and then adjust the Contrast only if further adjustment is necessary.
Press the
button to increase the contrast and press the
button to decrease the contrast (min 0 / max 100).
The Contrast function adjusts the degree of difference between darkness and lightness on the monitor screen.
Auto Adjust
Even though your computer recognizes your monitor on startup, the Auto Adjustment function optimizes the display settings for use with your
particular setup.
Auto Adjustment allows the monitor to self-adjust to the incoming video signal. After using Auto Adjustment, you can further tune your monitor
by using the Pixel Clock (Coarse) and Phase (Fine) controls under Display Settings.
NOTE: In most cases, Auto Adjust produces the best image for your configuration.
NOTE: Auto Adjust option is only available when you are using the analog (VGA) connector.
Input Source
Use the Input Source menu to select between the different video signals that may be connected to your monitor.
Auto Select
Press
to select Auto Select, the monitor auto detects either the VGA input or the DVI-D input or DislpayPort input.
VGA
Select the VGA input when you are using the analog (VGA) connector. Press
DVI-D
to select the VGA input source.
Select the DVI-D input when you are using the Digital (DVI) connector. Press
to select the DVI input source.
DisplayPort
Select the DisplayPort input when you are using the DisplayPort (DP) connector. Press
Color Settings
Use Color Settings to adjust the color setting mode.
Input Color Format
Allows you to set the video input mode to:
to select the DisplayPort input source.
RGB: Select this option if your monitor is connected to a computer or DVD player using the VGA and DVI cable.
YPbPr: Select this option if your monitor is connected to a DVD player by YPbPr to VGA, or YPbPr to DVI cable; or if the DVD color output setting
is not RGB.
Preset Modes
When you select Preset Modes, you can choose Standard, Multimedia, Movie, Game, Text, Warm, Cool or Custom Color from the list.
Standard: Loads the monitor's default color settings. This is the default preset mode.
Multimedia: Loads color settings ideal for multimedia applications.
Movie: Loads color settings ideal for movies.
Game: Loads color settings ideal for most gaming applications.
Text: Loads brightness and sharpness settings ideal for viewing texts.
Warm: Increase the color temperature. The screen appears warmer with a red/yellow tint.
Cool: Decreases the color temperature. The screen appears cooler with a blue tint.
Custom Color: Allows you to manually adjust the color settings. Press the
values and create your own preset color mode.
and
buttons to adjust the three colors (R, G, B)
Hue
This feature can shift the color of the video image to green or purple. This is used to adjust the desired flesh tone color. Use
adjust the hue from '0' to '100'.
Press
to increase the green shade of the video image.
Press
to increase the purple shade of the video image.
NOTE:: Hue adjustment is available only when you select Movie or Game preset mode.
Saturation
This feature can adjust the color saturation of the video image. Use
Press
to increase the monochrome appearance of the video image.
Press
to increase the colorful appearance of the video image.
or
to adjust the saturation from '0' to '100'.
Reset Color Settings
NOTE: Saturation adjustment is available only when you select Movie or Game preset mode.
Reset your monitor color settings to the factory settings.
Display Settings
Use the Display Settings to adjust image.
or
to
Aspect Ratio
NOTE: Aspect Ratio is not available in P1913S.
Adjust the image ratio to Wide 16:10, 5:4 or 4:3.
NOTE: Aspect Ratio is not available in P1913S.
Horizontal Position
Use
or
to adjust the image left or right. Minimum is '0' (-). Maximum is '100' (+).
Use
or
to adjust the image up or down. Minimum is '0' (-). Maximum is '100' (+).
Vertical Position
NOTE: Horizontal Position and Vertical Position adjustments are only available for "VGA" input.
Sharpness
This feature can make the image look sharper or softer. Use
Pixel Clock
to adjust the sharpness from '0' to '100'.
The Phase and Pixel Clock adjustments allow you to adjust your monitor to your preference.
Use
Phase
or
or
to adjust for best image quality.
If satisfactory results are not obtained using the Phase adjustment, use the Pixel Clock (coarse) adjustment and then use Phase (fine), again.
NOTE: Pixel Clock and Phase adjustments are only available for "VGA" input.
Dynamic Contrast
Dynamic Contrast adjusts the contrast ratio to 2M to 1.
Press the
Reset Display Settings
button to select the Dynamic Contrast "On" or "Off" .
NOTE: Dynamic Contrast provides higher contrast if you select Game or Movie preset mode.
Select this option to restore default display settings.
Other Settings
Select this option to adjust the settings of the OSD, such as, the languages of the OSD, the amount of time the menu remains on screen, and so
on.
Language
Language options set the OSD display to one of the eight languages (English, Spanish, French, German, Brazilian Portuguese, Russian, Simplified
Chinese or Japanese).
Menu Transparency
Select this option to change the menu transparency by pressing the
Menu Timer
buttons (Minimum: 0 ~ Maximum: 100).
OSD Hold Time: sets the length of time the OSD will remain active after the last time you pressed a button.
Use
Menu Lock
and
or
to adjust the slider in 1 second increments, from 5 to 60 seconds.
Controls user access to adjustments. When Lock is selected, no user adjustments are allowed. All buttons are locked.
NOTE:
Lock function – Either soft lock (through the OSD menu) or hard lock (press and hold the button above the power button for 10 seconds)
Unlock function– Only hard unlock (press and hold the button above the power button for 10 seconds)
Menu Rotation
Rotates the OSD by 90 degrees counter-clockwise. You can adjust the menu according to your Display Rotation.
Energy Smart
To turn on or off dynamic dimming.
The dynamic dimming feature automatically reduces the screen's brightness level when the displayed image contains a high proportion of bright
areas.
To turn on or off Audio Power during Power Save mode.
Power Save Audio
DDC/CI
DDC/CI (Display Data Channel/Command Interface) allows your monitor parameters (brightness, color balance, and etc.) to be adjustable via the
software on your computer. You can disable this feature by selecting "Disable".
Enable this feature for best user experience and optimum performance of your monitor.
LCD Conditioning
Helps reduce minor cases of image retention. Depending on the degree of image retention, the program may take some time to run. You can
enable this feature by selecting "Enable".
Factory Reset
Reset all OSD settings to the factory preset values.
Personalize
Users can choose a feature from "Preset Modes", "Brightness/Contrast", "Auto Adjust", "Input Source", "Aspect Ratio" or "Menu Rotation" and set
it as a shortcut key.
NOTE: This monitor has a built-in feature to automatically calibrate the brightness to compensate for LED aging.
OSD Warning Messages
When the Energy Smart or Dynamic Contrast feature is enabled (in these preset modes: Game or Movie), the manual brightness adjustment is disabled.
When the monitor does not support a particular resolution mode, you will see the following message:
This means that the monitor cannot synchronize with the signal that it is receiving from the computer. See Monitor Specifications for the Horizontal and Vertical frequency
ranges addressable by this monitor. Recommended mode is 1440 x 900 (for the P1913)/1280 x 1024 (for the P1913S)/1680 x 1050 (for the P2213).
You will see the following message before the DDC/CI function is disabled:
When the monitor enters the Power Save mode, the following message appears:
Activate the computer and wake up the monitor to gain access to the OSD.
If you press any button other than the power button, one of the following messages will appear depending on the selected input:
VGA/DVI-D/DP input
If either VGA or DVI-D or DP input is selected and the corresponding cable is not connected, a floating dialog box as shown below appears.
or
See Solving Problems for more information.
or
Setting the Maximum Resolution
To set the maximum resolution for the monitor:
Windows Vista® or Windows ® 7:
1.
2.
3.
4.
Right-click on the desktop and select Personalization.
Click Change Display Settings.
Move the slider-bar to the right by pressing and holding the left mouse button and adjust the screen resolution.
Click OK.
If you do not see the recommended resolution as an option, you may need to update your graphics driver. Depending on your computer, complete one of the following procedures:
If you have a Dell desktop or portable computer:
Go to support.dell.com, enter your service tag, and download the latest driver for your graphics card.
If you are using a non-Dell computer (portable or desktop):
Go to the support site for your computer and download the latest graphic drivers.
Go to your graphics card website and download the latest graphic drivers.
Using Dell Soundbar
The soundbar has an on/off power and rotary volume control to adjust the overall sound system, a LED for power indication and two audio headset jacks.
1
Attach mechanism
2
Power/Volume control
3
Headphone jacks
4
Power indicator
Using the Tilt, Swivel, and Vertical Extension
NOTE: This is applicable for a monitor with a stand. When any other stand is bought, please refer to the respective stand setup guide for set up instructions.
Tilt, Swivel
With the stand attached to the monitor, you can tilt and swivel the monitor for the most comfortable viewing angle.
NOTE: The stand is detached when the monitor is shipped from the factory.
Vertical Extension
NOTE: The stand extends vertically up to 130 mm. The figure below illustrates how to extend the stand vertically.
Rotating the Monitor
Before you rotate the monitor, your monitor should be fully vertically extended (Vertical Extension) and fully tilted (Tilt) up to avoid hitting the bottom edge of the monitor.
NOTE: To use the Display Rotation function (Landscape versus Portrait view) with your Dell computer, you require an updated graphics driver that is not included with this monitor. To
download the graphics driver, go to support.dell.com and see the Download section for Video Drivers for latest driver updates.
NOTE: When in the Portrait View Mode, you may experience performance degradation in graphic-intensive applications (3D Gaming and etc.).
Adjusting the Rotation Display Settings of Your System
After you have rotated your monitor, you need to complete the procedure below to adjust the Rotation Display Settings of your System.
NOTE: If you are using the monitor with a non-Dell computer, you need to go the graphics driver website or your computer manufacturer website for information on rotating the
'contents' on your display.
To adjust the Rotation Display Settings:
1. Right-click on the desktop and click Properties.
2. Select the Settings tab and click Advanced.
3. If you have an ATI graphics card, select the Rotation tab and set the preferred rotation.
If you have an nVidia graphics card, click the nVidia tab, in the left-hand column select NVRotate, and then select the preferred rotation.
If you have an Intel® graphics card, select the Intel graphics tab, click Graphic Properties, select the Rotation tab, and then set the preferred rotation.
NOTE: If you do not see the rotation option or it is not working correctly, go to support.dell.com and download the latest driver for your graphics card.
Back to Contents Page
Back to Contents Page
Troubleshooting
Dell™ P1913/P1913S/P2213 Monitor User's Guide
Self-Test
Built-in Diagnostics
Common Problems
Product Specific Problems
Universal Serial Bus (USB) Specific Problems
Dell™ Soundbar Problems
WARNING: Before you begin any of the procedures in this section, follow the Safety Instructions.
Self-Test
Your monitor provides a self-test feature that allows you to check whether your monitor is functioning properly. If your monitor and computer are properly connected but the monitor screen remains
dark, run the monitor self-test by performing the following steps:
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer. To ensure proper self-test operation, remove all video cables from the back of computer.
3. Turn on the monitor.
The floating dialog box should appear on-screen (against a black background), if the monitor cannot sense a video signal and is working correctly. While in self-test mode, the power LED
remains blue. Also, depending upon the selected input, one of the dialogs shown below will continuously scroll through the screen.
or
or
4. This box also appears during normal system operation, if the video cable becomes disconnected or damaged.
5. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor.
If your monitor screen remains blank after you use the previous procedure, check your video controller and computer, because your monitor is functioning properly.
Built-in Diagnostics
Your monitor has a built-in diagnostic tool that helps you determine if the screen abnormality you are experiencing is an inherent problem with your monitor, or with your computer and video card.
NOTE: You can run the built-in diagnostics only when the video cable is unplugged and the monitor is in self-test mode.
To run the built-in diagnostics:
1. Ensure that the screen is clean (no dust particles on the surface of the screen).
2. Unplug the video cable(s) from the back of the computer or monitor. The monitor then goes into the self-test mode.
3. Press and hold Button 1 and Button 4 on the front panel simultaneously for 2 seconds. A gray screen appears.
4.
5.
6.
7.
Carefully inspect the screen for abnormalities.
Press Button 4 on the front panel again. The color of the screen changes to red.
Inspect the display for any abnormalities.
Repeat steps 5 and 6 to inspect the display in green, blue, black, white and text screens.
The test is complete when the white screen appears. To exit, press Button 4 again.
If you do not detect any screen abnormalities upon using the built-in diagnostic tool, the monitor is functioning properly. Check the video card and computer.
Common Problems
The following table contains general information about common monitor problems you might encounter and the possible solutions:
Common Symptoms
No Video/Power LED off
What You Experience
No picture
Possible Solutions
Ensure that the video cable connecting the monitor and the computer is properly connected and secure.
Verify that the power outlet is functioning properly using any other electrical equipment.
Ensure that the power button is depressed fully.
Ensure that the correct input source is selected via the Input Source Select button.
No Video/Power LED on
No picture or no brightness
Increase brightness & contrast controls via OSD.
Perform monitor self-test feature check.
Check for bent or broken pins in the video cable connector.
Run the built-in diagnostics.
Ensure that the correct input source is selected via the Input Source Select button.
Poor Focus
Picture is fuzzy, blurry, or ghosting
Perform Auto Adjust via OSD.
Adjust the Phase and Pixel Clock controls via OSD.
Eliminate video extension cables.
Reset the monitor to Factory Settings.
Change the video resolution to the correct aspect ratio.
Shaky/Jittery Video
Wavy picture or fine movement
Perform Auto Adjust via OSD.
Adjust the Phase and Pixel Clock controls via OSD.
Reset the monitor to Factory Settings.
Check environmental factors.
Relocate the monitor and test in another room.
Missing Pixels
LCD screen has spots
Cycle power on-off.
Pixel that is permanently off is a natural defect that can occur in LCD technology.
For more information on Dell Monitor Quality and Pixel Policy, see Dell Support site at: support.dell.com.
Stuck-on Pixels
LCD screen has bright spots
Cycle power on-off.
Pixel that is permanently off is a natural defect that can occur in LCD technology.
For more information on Dell Monitor Quality and Pixel Policy, see Dell Support site at: support.dell.com.
Brightness Problems
Picture too dim or too bright
Reset the monitor to Factory Settings.
Auto Adjust via OSD.
Adjust brightness & contrast controls via OSD.
Geometric Distortion
Screen not centered correctly
Reset the monitor to Factory Settings.
Auto Adjust via OSD.
Adjust horizontal & vertical controls via OSD.
Horizontal/Vertical Lines
Screen has one or more lines
NOTE: When using DVI-D/DisplayPort input, the positioning adjustments are not available.
Reset the monitor to Factory Settings.
Perform Auto Adjust via OSD.
Adjust Phase and Pixel Clock controls via OSD.
Perform monitor self-test feature check and determine if these lines are also in self-test mode.
Check for bent or broken pins in the video cable connector.
Run the built-in diagnostics.
NOTE: When using DVI-D/DisplayPort input, the Pixel Clock and Phase adjustments are not available.
Synchronization Problems
Screen is scrambled or appears torn
Reset the monitor to Factory Settings.
Perform Auto Adjust via OSD.
Adjust Phase and Pixel Clock controls via OSD.
Perform monitor self-test feature check to determine if the scrambled screen appears in self-test mode.
Check for bent or broken pins in the video cable connector.
Restart the computer in the safe mode.
Safety Related Issues
Visible signs of smoke or sparks
Do not perform any troubleshooting steps.
Contact Dell immediately.
Intermittent Problems
Monitor malfunctions on & off
Ensure that the video cable connecting the monitor to the computer is connected properly and is secure.
Reset the monitor to Factory Settings.
Perform monitor self-test feature check to determine if the intermittent problem occurs in self-test mode.
Missing Color
Picture missing color
Perform monitor self-test feature check.
Ensure that the video cable connecting the monitor to the computer is connected properly and is secure.
Check for bent or broken pins in the video cable connector.
Wrong Color
Picture color not good
Change the Color Setting Mode in the Color Settings OSD to Graphics or Video depending on the application.
Try different Color Preset Settings in Color Settings OSD. Adjust R/G/B value in Color Settings OSD if the Color
Management is turned off.
Change the Input Color Format to PC RGB or YPbPr in the Advance Setting OSD.
Run the built-in diagnostics.
Image retention from a static image
Faint shadow from the static image
left on the monitor for a long period of displayed appears on the screen
time
Use the Power Management feature to turn off the monitor at all times when not in use (for more information,
see Power Management Modes).
Alternatively, use a dynamically changing screensaver.
Product Specific Problems
Specific Symptoms
Screen image is too small
What You Experience
Image is centered on screen, but does
not fill entire viewing area
Possible Solutions
Check the Scaling Ratio setting in the Image Setting OSD.
Reset the monitor to Factory Settings.
Cannot adjust the monitor with the
buttons on the front panel
OSD does not appear on the screen
Turn off the monitor, unplug the power cord, plug it back, and then turn on the monitor.
Check whether the OSD menu is locked. If yes, press and hold the button above the Power button for 10
seconds to unlock (for more information, see Menu Lock).
No Input Signal when user controls are No picture, the LED light is blue.
pressed
Check the signal source. Ensure the Computer is not in the power saving mode by moving the mouse or pressing
any key on the keyboard.
Check whether the signal cable is plugged in properly. Re-plug the signal cable if necessary.
Reset the computer or video player.
The picture does not fill the entire
screen.
Due to different video formats (aspect ratio) of DVDs, the monitor may display in full screen.
Run the built-in diagnostics.
The picture cannot fill the height or
width of the screen
NOTE: When choosing DVI-D mode, the Auto Adjust function will not be available.
Universal Serial Bus (USB) Specific Problems
Specific Symptoms
USB interface is not working
What You Experience
USB peripherals are not working
Possible Solutions
Check that your monitor is turned ON.
Reconnect the upstream cable to your computer.
Reconnect the USB peripherals (downstream connector).
Switch off and then turn on the monitor again.
Reboot the computer.
Some USB devices like external portable HDD require higher electric current; connect the device directly to the
computer system.
High Speed USB 2.0 interface is slow.
High Speed USB 2.0 peripherals
working slowly or not working at all
Check that your computer is USB 2.0-capable.
Some computers have both USB 2.0 and USB 1.1 ports. Ensure that the correct USB port is used.
Reconnect the upstream cable to your computer.
Reconnect the USB peripherals (downstream connector).
Reboot the computer.
Dell™ Soundbar Problems
Common Symptoms
No Sound
What You Experience
No power to Soundbar - the power
indicator is off
Possible Solutions
Turn the Power/Volume knob on the Soundbar clockwise to the middle position; check if the power indicator
(Blue LED) on the front of the Soundbar is illuminated.
Confirm that the power cable from the Soundbar is plugged into the adapter.
No Sound
Soundbar has power - power indicator
is on
Plug the audio line-in cable into the computer's audio out jack.
Set all Windows volume controls to their maximum.
Play some audio content on the computer (i.e. audio CD, or MP3).
Turn the Power/Volume knob on the Soundbar clockwise to a higher volume setting.
Clean and reseat the audio line-in plug.
Test the Soundbar using another audio source (i.e. portable CD player).
Distorted Sound
Computer's sound card is used as the
audio source
Clear any obstructions between the Soundbar and the user.
Confirm that the audio line-in plug is completely inserted into the jack of the sound card.
Set all Windows volume controls to their midpoints.
Decrease the volume of the audio application.
Turn the Power/Volume knob on the Soundbar counter-clockwise to a lower volume setting.
Clean and reseat the audio line-in plug.
Troubleshoot the computer's sound card.
Test the Soundbar using another audio source (i.e. portable CD player).
Distorted Sound
Other audio source is used
Clear any obstructions between the Soundbar and the user.
Confirm that the audio line-in plug is completely inserted into the jack of the audio source.
Decrease the volume of the audio source.
Turn the Power/Volume knob on the Soundbar counter-clockwise to a lower volume setting.
Clean and reseat the audio line-in plug.
Unbalanced Sound Output
Sound from only one side of Soundbar
Clear any obstructions between the Soundbar and the user.
Confirm that the audio line-in plug is completely inserted into the jack of the sound card or audio source.
Set all Windows audio balance controls (L-R) to their midpoints.
Clean and reseat the audio line-in plug.
Troubleshoot the computer's sound card.
Test the Soundbar using another audio source (i.e. portable CD player).
Low Volume
Volume is too low
Clear any obstructions between the Soundbar and the user.
Turn the Power/Volume knob on the Soundbar clockwise to the maximum volume setting.
Set all Windows volume controls to their maximum.
Increase the volume of the audio application.
Test the Soundbar using another audio source (i.e. portable CD player).
Back to Contents Page
Back to Contents Page
Appendix
Dell™ P1913/P1913S/P2213 Monitor User's Guide
Safety Instructions
FCC Notice (U.S. Only) and Other Regulatory Information
Contacting Dell
WARNING: Safety Instructions
WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical
hazards, and/or mechanical hazards.
For information on safety instructions, see the Product Information Guide.
FCC Notices (U.S. Only) and Other Regulatory Information
For FCC notices and other regulatory information, see the regulatory compliance website located at www.dell.com\regulatory_compliance.
Contacting Dell
For customers in the United States, call 800-WWW-DELL (800-999-3355).
NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services may not be
available in your area. To contact Dell for sales, technical support, or customer service issues:
1.
Visit support.dell.com.
2.
Verify your country or region in the Choose A Country/Region drop-down menu at the bottom of the page.
3.
Click Contact Us on the left side of the page.
4.
Select the appropriate service or support link based on your need.
5.
Choose the method of contacting Dell that is convenient for you.
Back to Contents Page
Back to Contents Page
Setting Up Your Monitor
Dell™ P1913/P1913S/P2213 Monitor User's Guide
Setting the display resolution
For maximum display performance with Microsoft ® Windows ® operating systems, set the display resolution to 1440 x 900 (for the P1913)/1280 x 1024 (for the
P1913S)/1680 x 1050 (for the P2213) pixels by performing the following steps:
In Windows Vista® or Windows ® 7:
1. Right-click on the desktop and click Personalization.
2. Click Change Display Settings.
3. Move the slider-bar to the right by pressing and holding the left-mouse button and adjust the screen resolution.
4. Click OK.
If you do not see the recommended resolution as an option, you may need to update your graphics driver. Please choose the scenario below that best describes the
computer system you are using, and follow the given steps.
1: If you have a Dell™ desktop or a Dell™ portable computer with internet access.
2: If you have a non Dell™ desktop, portable computer, or graphics card.
Back to Contents Page
Back to Contents Page
Setting Up Your Monitor
Dell™ P1913/P1913S/P2213 Monitor User's Guide
If you have a Dell™ desktop or a Dell™ portable computer with internet access
1. Go to http://support.dell.com, enter your service tag, and download the latest driver for your graphics card.
2. After installing the drivers for your Graphics Adapter, attempt to set the resolution to 1440 x 900 (for the P1913)/1280 x 1024 (for the
P1913S)/1680 x 1050 (for the P2213) again.
NOTE: If you are unable to set the resolution to 1440 x 900/1280 x 1024/1680 x 1050, please contact Dell™ to inquire about a Graphics Adapter that supports
these resolutions.
Back to Contents Page
Back to Contents Page
Setting Up Your Monitor
Dell™ P1913/P1913S/P2213 Monitor User's Guide
If you have a non Dell™ desktop, portable computer, or graphics card
In Windows Vista® or Windows ® 7:
1. Right-click on the desktop and click Personalization.
2. Click Change Display Settings.
3. Click Advanced Settings.
4. Identify your graphics controller supplier from the description at the top of the window (e.g. NVIDIA, ATI, Intel etc.).
5. Refer to the graphic card provider website for updated driver (for example, http://www.ATI.com OR http://www.NVIDIA.com ).
6. After installing the drivers for your Graphics Adapter, attempt to set the resolution to 1440 x 900 (for the P1913)/1280 x 1024 (for the P1913S)/1680 x
1050 (for the P2213) again.
NOTE: If you are unable to set the recommended resolution, please contact the manufacturer of your computer or consider purchasing a graphics adapter that
will support the video resolution.
Back to Contents Page