15-INCH VALUE

TFT-LCD MONITOR

USER MANUAL

Please read this manual thoroughly before use, and keep it handy for future reference.

SAFETY INSTRUCTION

………………………………………………………….……

CAUTIONS

……………………………………………………………..........................

FCC RF INTERFERENCE STATEMENT …………………………….......................

CONNECTING WITH EXTERNAL EQUIPMENT ……………………………………

REMOTE FUNCTIONS …………………………………………………………………

CONTROLS AND FUNCTIONS ………………………………………………………..

MOUNTING GUIDE ……………………………………………………………………..

D-SUB CONNECTOR PIN ASSIGNMENTS …………………………………………

POWER MANAGEMENT ………………………………………………………………

SPECIFICATIONS ………………………………………………………………………

TROUBLE SHOOTING GUIDE ………………………………………………….........

This Monitor was

Manufactured by ISO 9001

Certified Factory

2 ~ 3

4

5

6

7

8 ~ 12

13

14

15

16

17

- 1 -

Important Safety Instruction

1. Read these instructions.

2. Keep these Instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers,stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug.

Apolarized plug has two blades with one wider than the other.

Agrounding type plug has two blades and a third grounding prong.

The wide blade or the third prong are provided for your safety.

If the provided plug does not fit into your outlet, consult an electrician for replacement of the bsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point where they exit from the apparatus.

11. Only use attachment/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused

for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped.

- 2 -

- The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed no the apparatus.

- Minimum distances(e.g. 10cm) around the apparatus for sufficient ventilation.

“WARNING – To reduce the risk of fire or electric shock, do not expose the apparatus to rain or moisture.”

“The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.”

This symbol is intended to alert the user to the presence of uninsulated : dangerous voltage with in the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance.

- 3 -

CAUTION

The power supply cord is used as the main disconnect device, ensure that the socket-outlet is located/installed near the equipment and is easily accessible.

ATTENTION

N

Le cordon d`alimentation est utillsé comme interrupteur général. La prise de courant doit être

située ou installée à proximité du matériel et être facile d`accès

▶ NEVER REMOVE THE BACK COVER

Removal of the back cover should be carried out only by qualified personnel.

▶ DO NOT USE IN HOSTILE ENVIRONMENTS

To prevent shock or fire hazard, do not expose the unit to rain or moisture.

This unit is designed to be used in the office or home. Do not subject the unit to vibrations, dust of corrosive gases.

▶ KEEP IN A WELL VENTILATED PLACE

Ventilation holes are provided on the cabinet to prevent the temperature from rising.

Do not cover the unit or place anything on the top of unit.

▶ AVOID HEAT

Avoid placing the unit in direct sunshine or near a heating appliance.

▶ TO ELIMINATE EYE FATIGUE

Do not use the unit against a bright back ground and where sunlight or other light sources will shine directly on the monitor.

▶ BE CAREFUL OF HEAVY OBJECT

Neither the monitor itself nor any other heavy object should rest on the power cord.

Damage to a power cord can cause fire or electrical shock.

- 4 -

NOTE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio, TV technician for help.

- Only shielded interface cable should be used.

Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment.

▶ DOC COMPLIANCE NOTICE

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the radio interference regulation of Canadian Department of communications.

- 5 -

A. REAR CONNECTION

1 2 3

1. DC 12V

2. VGA

PC Signal Input

3. VIDEO 1 IN

Composite signal Input for AV1

4. VIDEO 1 OUT

Video looping output for AV1

5. VIDEO 2 IN

Composite signal Input for AV2

6. VIDEO 2 OUT

Video looping output for AV2

7 & 8 AUDIO L & R

Stereo Audio Signal Input

9. S-VIDEO IN

Y/C separated signal input

10. S-VIDEO OUT

Y/C separated signal looping output

11. PC STEREO IN

4 5 6 7 8 9 10 11

- 6 -

B. REMOTE CONTROLLER(Optional)

1. POWER( )

Turns the power ON or OFF.

There will be a few seconds delay before the display appears.

2. SOURCE

Selects an input source.

3. APC (Auto Picture Control)

Selects a picture mode.

4. ACC (Auto Color Control)

Selects a color mode.

5. AV1

Select AV1 mode

6. AV2

Select AV2 mode

7. S-VIDEO

Select S-VODEO mode

8. PC

Select PC mode

9. AUTO

Auto geometry adjustment in PC Source.

10. MUTE

Mutes the sound.

11. MENU

Activates and exits the On Screen Display.

12. EXIT

Exits the On Screen Display.

13. VOL(◀ & ▶)

Increases or decreases the level of audio volume.

14. UP & DOWN

Moves upwards or downwards in OSD menu.

15. ENTER

Enters an OSD submenu or accepts your selection

16. INFO

Displays the information about input source.

17. STILL

Pauses the picture.

- 7 -

C. FRONT & BOTTOM KEY CONTROL

1. SOURCE/

Selects an input source.

Enters a submenu or accepts your selection in the OSD menu.

2. MENU

Activates or exits the OSD.

Moves previous menu or status in the OSD.

3 & 4. AUTO/▼ & ▲

Moves another option in the OSD.

The

AUTO/▼ button is auto adjustment function in the VGA input.

5 & 6. ◀ VOL ▶

Adjust the volume or menu settings.

7. IR Sensor

Remote controller sensor.

8. / I & LED

Turns the power on or off. There will be a few seconds delay before the display appears.

Turned on is green color and turned off is red color.

- 8 -

OSD MENU DESCRIPTION

All picture, sound settings and setup for the monitor can be adjusted in the OSD menu.

(On Screen Display)

To adjust the OSD screen:

1. Press the Menu button to enter the OSD menu.

2. Press the ▲/▼ buttons to select the desired option. The selected option is highlighted.

3. Press the ▶ button to enter the submenu for adjusting items.

4. Change the value you wish to adjust by using the ▲/▼ buttons.

5. Press the ◀ button to exit the submenu for adjusting items.

6. Press the Menu button to exit the OSD menu.

A. Custom

Option Function Value

Brightness Adjusts brightness of the screen. 0 ~ 100.

Contrast

Color

1)

Adjusts intensity of the image.

Adjusts color of the picture.

0 ~ 100.

0 ~ 100.

Tint

2)

Adjusts tint of the picture. 0 ~ 100.

Sharpness

1)

Adjusts sharpness of the picture. 0 ~ 100.

1) Unavailable in PC input.

2) Unavailable in PAL system.

- 9 -

B. Picture/Sound

< AV1, AV2 & S-Video > < PC >

Option Function

Picture Mode Sets picture mode.

Color Tone Sets color tone.

Mute

Volume

Value

See table below.

See table below.

Mutes speaker sound. Off or On.

Adjust the level of audio volume. 0 ~ 100.

Size

PC

1)

Inactivated.

See table below.

1) Unavailable in AV 1, AV2 & S-Video inputs.

Picture Mode (In AV1, AV2 & S-Video inputs)

Custom Applies user selected values (Brightness, Contrast, Tint and Sharpness).

Dynamic Provides enhanced contrast and sharpness.

Standard Provides standard contrast and sharpness.

Movie Is recommended for viewing film-based content.

Mild Reduces contras and sharpness.

Picture Mode (In PC input)

Custom Applies user selected values (Brightness and Contrast).

High

Middle

Low

Increases the contrast of picture.

Provides standard brightness and contrast.

Decreases the brightness and contrast of picture.

- 10 -

Color Tone

Custom

1)

To manually adjust the color tones(Red, Green and Blue).

Cool Gives the white color a bluish tint.

Normal

Warm

Gives the white color a neutral tint.

Gives the white color a reddish tint.

1) Unavailable in AV1, AV2 & S-Video.

PC

Option

Auto Adjust

Phase

Function

Auto geometry adjustment.

Value

Adjusts the number of horizontal picture elements. 0 ~ 100.

H-Position Adjusts the horizontally picture position.

V-Position Adjusts the vertically picture position.

Frequency Adjusts the vertical noise of screen image.

0 ~ 100.

0 ~ 100.

0 ~ 100.

- 11 -

C. Setup

Option

Reset

Function

Resets the monitor settings to their factory default.

Value

Language Sets the language of the OSD menu.

English, French, Deutsch,

Italian, Spanish, Portuguese or Nederland.

OSD Tone

Blue Screen

Changes background of monitor menus

(e.g. input source & information).

Displays a blue screen if the monitor receives no signal.

Transparency or Blue.

Off or On.

Key Lock

1)

Locks all buttons of the monitor.

Note: Use remote controller to unlock.

Off or On.

1) How to unlock

① On the front key: Press the SOURCE/SELECT and MENU button at the same time over 3 seconds.

② On the Remote Controller: The Remote Controller operates well because the Key Lock function is only allowed for the front key of this product.

- 12 -

Wall mounting (Optional)

The LCD monitor is suitable for wall mounting by using the VESA 100 standard wall mount (not included in the delivery).

※ Attention!

You must use four M4x10 screws to assemble this monitor and the wall mount bracket.

- 13 -

▶ PIN ASSIGNMENTS

Pin 1 RED VIDEO

2 GREEN VIDEO

3

4

5

6

BLUE VIDEO

GROUND

GROUND

RED GROUND

7

8

GREEN GROUND

BLUE GROUND

D-SUB

9

10

11

12

13

14

15

SIGNAL CABLE DETECT

GROUND

SDA(for DDC)

H-SYNC.(or H+V SYNC.)

V-SYNC.

SCL(for DDC)

▶ ACCESSORIES

1. Power cord

2. Power adaptor

3. User ’s manual

4. PC cable

5. Stereo cable (Optional)

6. Remote Control (Optional)

7. Batteries (Optional)

8. Wall mount (Optional)

- 14 -

POWER CONSUMPTION

MODE POWER CONSUMPTION

ON

STANDBY

SUSPEND

ACTIVE OFF

< 36W

< 11W

< 11W

< 8.5W

LED INDICATOR

The power management feature of the monitor is comprised of four stages:

On(Green), Standby, Suspend, Active off(Red on/off 1 sec) and Unsupported mode(Green).

MODE LED COLOR MONITOR OPERATION

GREEN ON

STANDBY

SUSPEND

ACTIVE OFF

UNSUPPORTED

MODE

POWER OFF

Blinking RED

GREEN

RED

Normal Operation

Screen blanks after preset idle time

And some electronic circuits or all

Circuitry in the monitor shut down.

Normal operation but the on screen

Display will show error massage

Not Operation

- 15 -

LCD-Type

15"

15˝ Diagonal AM-TFT(Active-Matrix)

Pixel pitch (mm): 0.297(H) x 0.297(V)

BRIGHTNESS: 225cd/㎡(Typical)

CONTRAST RATIO: 600:1(Typical)

RESPONSE TIME: 8ms(Typical)

RESOLUTION (H x V) 1024x768@60Hz

FREQUENCY

HORIZONTAL: 31~48kHz

VERTICAL: 56~75Hz

VGA(RGB-PC)

VIDEO (2ch input 1.0Vpp, 75Ω terminated, loop-through out)

INPUT SIGNAL S-VIDEO(1ch input (Y/C), loop-through out)

AV(composite) Sound in

PC Stereo Sound

ACTIVE DISPLAY AREA

(W x H)

PACKING DIMENSIONS

(W x H x D)

304.1mm x 228.1mm

435mm x 472mm x 233mm

Net Weight : 3.7kg

WEIGHT

Gross Weight : 5.7kg

ELECTRICAL RATINGS DC 12V / 3A

▶▶ NOTE :

Technical specifications are subject to change without notice.

- 16 -

WEEE Symbols

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other

European countries with separate collection systems)

This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

MEMO

- 17 -

MEMO

MEMO

P/N : L39ME0220_Rev.1