advertisement
Always there to help you
Register your product and get support at www.philips.com/welcome
Question?
Contact
Philips
HTL5120
User manual
Contents
1 Important
2 Your SoundBar
3 Connect
Connect digital devices through HDMI 7
Connect audio from TV and other devices
4 Use your SoundBar
5 Wall mount your SoundBar
6 Product specifications
7 Troubleshooting
8 Notice
EN 1
1 Important
Read and understand all instructions before you use your product. If damage is caused by failure to follow instructions, the warranty does not apply.
Safety
Risk of electric shock or fire!
• Never expose the product and accessories to rain or water. Never place liquid containers, such as vases, near the product.
If liquids are spilt on or into the product, disconnect it from the power outlet immediately. Contact Philips Consumer
Care to have the product checked before use.
• Never place the product and accessories near naked flames or other heat sources, including direct sunlight.
• Never insert objects into the ventilation slots or other openings on the product.
• Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
• Disconnect the product from the power outlet before lightning storms.
• When you disconnect the power cord, always pull the plug, never the cable.
Risk of short circuit or fire!
• Before you connect the product to the power outlet, ensure that the power voltage matches the value printed on the back or bottom of the product. Never connect the product to the power outlet if the voltage is different.
Risk of injury or damage to the SoundBar!
• For wall-mountable products, use only the supplied wall mount bracket. Secure the wall mount to a wall that can support the combined weight of the product and the wall mount. Koninklijke Philips Electronics
2 EN
N.V. bears no responsibility for improper wall mounting that results in accident, injury or damage.
• Never place the product or any objects on power cords or on other electrical equipment.
• If the product is transported in temperatures below 5°C, unpack the product and wait until its temperature matches room temperature before connecting it to the power outlet.
• Parts of this product can be made of glass. Handle with care to avoid injury and damage.
Risk of overheating!
• Never install this product in a confined space. Always leave a space of at least four inches around the product for ventilation.
Ensure curtains or other objects never cover the ventilation slots on the product.
Risk of contamination!
• Do not mix batteries (old and new or carbon and alkaine, etc.).
• Danger of explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type.
• Remove batteries if they are exhausted or if the remote control is not to be used for a long time.
• Batteries contain chemical substances, they should be disposed of properly.
Risk of swallowing batteries!
• The product/remote control may contain a coin/button type battery, which can be swallowed. Keep the battery out of reach of children at all times! If swallowed, the battery can cause serious injury or death.
Severe internal burns can occur within two hours of ingestion.
• If you suspect that a battery has been swallowed or placed inside any part of the body, seek immediate medical attention.
• When you change the batteries, always keep all new and used batteries out of reach of children. Ensure that the battery compartment is completely secure after you replace the battery.
• If the battery compartment cannot be completely secured, discontinue use of the product. Keep out of reach of children and contact the manufacturer.
This is CLASS II apparatus with double insulation, and no protective earth provided.
Care for your product
Use only microfiber cloth to clean the product.
Care of the environment
Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/
EC. Please inform yourself about the local separate collection system for electrical and electronic products.
Please act according to your local rules and do not dispose of your old products with your normal household waste.
Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot be disposed with normal household waste.
Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health.
Help and support
Philips provides extensive online support. Visit our website at www.philips.com/support to:
• download the complete user manual
• print the quick start guide
• watch video tutorials (available only for selected models)
• find answers to frequently answered questions (FAQs)
• email us a question
• chat with our support representative.
Follow the instructions on the website to select your language, and then enter your product model number.
Alternatively, you can contact Philips Consumer
Care in your country. Before you contact
Philips, note down the model number and serial number of your product. You can find this information on the back or bottom of your product.
EN 3
4 EN
2 Your SoundBar
Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your
SoundBar at www.philips.com/welcome.
This section includes an overview of the main unit.
Main unit
Bluetooth a (Standby-On/Standby indicator)
• Switch the SoundBar on or to standby.
• When the SoundBar is in standby, the standby indicator turns red.
b Volume indicator/Source indicators
When you change volume, volume indicators light up to indicate the volume level.
Source indicator lights up when a source is selected.
• HDMI ARC: Lights up when you select
HDMI ARC as the input source.
• HDMI 1: Lights up when you select
HDMI IN 1 as the input source. Blinks for five seconds when you play Dolby audio.
• HDMI 2: Lights up when you select
HDMI IN 2 as the input source. Blinks for five seconds when you play DTS audio.
• OPTICAL: Lights up when you switch to optical input source.
• AUX/Bluetooth: Lights up when you switch to analog input source. Blinks when you switch to Bluetooth mode.
• COAXIAL: Lights up when you switch to coaxial input source. c Volume indicator/V. SURR indicator
• When you change volume, volume indicators light up to indicate the volume level.
• Lights up when you select Virtual
Surround sound.
d Volume indicator/MUSIC iLINK indicator
• When you change volume, volume indicators light up to indicate the volume level.
• Lights up when you select MUSIC iLINK as the input source.
Remote control
This section includes an overview of the remote control.
d OPTICAL
Switch your audio source to the optical connection. e COAX
13
17
16
15
14
Bluetooth a (Standby-On)
• Switch the SoundBar on or to standby.
• When EasyLink is enabled, press and hold for at least three seconds to switch all connected HDMI CEC compliant devices to standby.
b HDMI 1
Switch your source to the HDMI IN 1 connection.
c HDMI 2
Switch your source to the HDMI IN 2 connection.
1
2
3
4
5
6
7
8
9
10
11
12
Switch your audio source to the coaxial connection. f MUSIC iLINK
Switch your audio source to the MUSIC iLINK connection.
g AUTO VOLUME ON/OFF
Turn auto volume on or off.
h AUDIO SYNC +/-
Increase or decrease audio delay.
i +/- (Volume)
Increase or decrease volume.
j TREBLE +/-
Increase or decrease treble.
k BASS +/-
Increase or decrease bass.
l V.SURR
Toggle between stereo and virtual surround sound.
m (Mute)
Mute or restore volume.
n NIGHT MODE ON/OFF
Turn night mode on or off.
o Bluetooth
Switch to Bluetooth mode.
p AUX
Switch your audio source to the AUX connection. q HDMI ARC
Switch your source to HDMI ARC connection. HDMI ARC can only be selected if you connect your SoundBar to an HDMI ARC compliant TV through
HDMI ARC.
Connectors
This section includes an overview of the connectors available on your SoundBar.
EN 5
6 EN
Rear connectors
a MUSIC iLINK
Audio input from an MP3 player.
Bottom connectors
g
6
5
4 a HDMI IN 1
Connect to the HDMI output on a digital device.
b HDMI IN 2
Connect to the HDMI output on a digital device.
1
2
3 c TO TV-HDMI OUT (ARC)
Connect to the HDMI input on the TV. d AC MAINS~
Connect to the power supply.
e AUDIO IN-AUX
Connect to an analog audio output on the
TV or an analog device. f DIGITAL IN-COAXIAL
Connect to a coaxial audio output on the
TV or a digital device. g DIGITAL IN-OPTICAL
Connect to an optical audio output on the
TV or a digital device.
3 Connect
This section helps you connect your SoundBar to a TV and other devices.
For information about the basic connections of your SoundBar and accessories, see the quick start guide.
Note
• For identification and supply ratings, refer to the type plate at the back or bottom of the product.
• Before you make or change any connections, make sure that all devices are disconnected from the power outlet.
• The HDMI ARC connector on the TV might be labeled differently. For details, see the TV user manual.
2
On your TV, turn on HDMI-CEC operations. For details, see the TV user manual.
Note
•
If your TV is not HDMI ARC compliant, connect an audio cable to hear the TV audio through your
SoundBar. (see 'Connect audio from TV and other devices' on page 8)
• If your TV has a DVI connector, you can use an HDMI/
DVI adapter to connect to TV. However, some of the features may not be available.
Connect to TV
Connect your SoundBar to a TV. You can listen to audio from TV programs through your
SoundBar. Use the best quality connection available on your SoundBar and TV.
Connect to TV through HDMI (ARC)
Your SoundBar supports HDMI with Audio
Return Channel (ARC). If your TV is HDMI ARC compliant, you can hear the TV audio through your SoundBar by using a single HDMI cable.
TV
1
Using a High Speed HDMI cable, connect the HDMI OUT (ARC) connector on your
SoundBar to the HDMI ARC connector on the TV.
Connect digital devices through HDMI
Connect a digital device such as a set-top box,
DVD/Blu-ray player, or games console to your
SoundBar through a single HDMI connection.
When you connect the devices in this way and play a file or game, the
• video is automatically displayed on your
TV, and
• audio is automatically played on your
SoundBar.
1
Using a High Speed HDMI cable, connect the HDMI OUT connector on your digital device to the HDMI IN 1/2 on your
SoundBar.
2
Connect your SoundBar to TV through
HDMI OUT (ARC).
• If the TV is not HDMI CEC compliant, select the correct video input on your
TV.
3
On the connected device, turn on HDMI-
CEC operations. For details, see the user manual of the device.
EN 7
Connect audio from TV and other devices
Play audio from TV or other devices through your Soundbar speakers.
Use the best quality connection available on your TV, Soundbar, and other devices.
Note
• When your Soundbar and TV are connected through
HDMI ARC, an audio connection is not required.
Option 1: Connect audio through a digital optical cable
Best quality audio
TV
1
Using an optical cable, connect the
OPTICAL connector on your SoundBar to the OPTICAL OUT connector on the TV or other device.
• The digital optical connector might be labeled SPDIF or SPDIF OUT.
Option 2: Connect audio through a digital coaxial cable
Good quality audio
8 EN
1
Using a coaxial cable, connect the
COAXIAL connector on your SoundBar to the COAXIAL/DIGITAL OUT connector on the TV or other device.
• The digital coaxial connector might be labeled DIGITAL AUDIO OUT.
Option 3: Connect audio through analog audio cables
Basic quality audio
1
Using an analog cable, connect the AUX connectors on your SoundBar to the
AUDIO OUT connectors on the TV or other device.
DVD
4 Use your
SoundBar
This section helps you use the SoundBar to play audio from connected devices.
Before you start
• Make the necessary connections described in the quick start guide and the user manual.
• Switch the SoundBar to the correct source for other devices.
Adjust the volume
0
1
Press +/- (Volume) to increase or decrease a volume level.
• To mute sound, press (Mute).
• To restore the sound, press (Mute) again or press +/- (Volume).
Volume indicator
• When you change volume, one or multiple
Volume indicator (up to 8 indicators) on the main unit light up to indicate a volume level. The more indicators light up, the higher the volume level is.
Bluetooth
60
• If you do not press the volume key for five seconds, the volume indicators light off, and the current source indicator and the sound mode indicator light up.
Choose your sound
This section helps you choose the ideal sound for your video or music.
Surround sound mode
Experience an immersive audio experience with surround sound modes.
1
Press V.SURR repeatedly to switch surround mode on or off.
» When surround mode is on, the
V.SURR indicator on the main unit lights up. Creates a surround listening experience.
» When the V.SURR indicator on the main unit turns off, two-channel stereo sound is on, ideal for listening to music.
Equalizer
Change the high frequency (treble) and low frequency (bass) settings of the SoundBar.
1
Press TREBLE +/- or BASS +/- to change the treble or bass level.
Treble/bass indicator
• When you change the treble or bass level, all the indicators on the main unit blink one by one. If the treble or bass level is set to the minimum, all the indicators turn off.
Auto volume
Turn the auto volume on to keep the volume constant when you switch to a different source.
1
Press AUTO VOLUME ON/OFF to turn auto volume on or off.
» When auto volume is turned on or off,
V.SURR indicator blinks once.
Synchronize picture and sound
If the audio and video are not synchronized, delay the audio to match the video.
1
Press AUDIO SYNC +/- to synchronize the audio with the video.
EN 9
Night mode
For quiet listening, decrease the volume of loud sounds when audio is played. Night mode is only available for Dolby Digital soundtracks.
1
Press NIGHT MODE ON/OFF to turn night mode on or off.
» When night mode is turned on or off,
V.SURR indicator blinks once.
Note
• If auto volume is set to turned on, you cannot enable the night mode.
MP3 player
Connect your MP3 player to play your audio files or music.
What you need
• An MP3 player.
• A 3.5mm stereo audio cable.
1
Using the 3.5mm stereo audio cable, connect the MP3 player to the MUSIC iLINK connector on your SoundBar.
2
Press MUSIC iLINK.
3
Press the buttons on the MP3 player to select and play audio files or music.
Play audio through Bluetooth
Through Bluetooth, connect the SoundBar with your Bluetooth device (such as an iPad, iPhone, iPod touch, Android phone, or laptop), and then you can listen to the audio files stored on the device through your SoundBar speakers.
What you need
• A Bluetooth device which supports
Bluetooth profile A2DP, and with Bluetooth version as 2.1 + EDR.
• The operational range between the
SoundBar and a Bluetooth device is approximately 10 meters (30 feet).
1
Press Bluetooth on the remote control to switch the SoundBar to Bluetooth mode.
» The AUX/Bluetooth indicator blinks at a fast rate.
2
On the Bluetooth device, switch on
Bluetooth, search for and select Philips
HTL5120 to start connection (see the user manual of the Bluetooth device on how to enable Bluetooth).
• When prompted for a password, enter
"0000".
» During connection, the indicator blinks at a lower rate.
3
Wait until you hear a beep sound from the
SoundBar.
» When the Bluetooth connection succeeds, and the AUX/Bluetooth indicator lights up.
» If the connection fails, the
AUX/Bluetooth indicator blinks continually at a lower rate.
4
Select and play audio files or music on your Bluetooth device.
• During play, if a call is coming, music play is paused. Play resumes when the call ends.
5
To exit Bluetooth, select other source.
• When your switch back to Bluetooth mode, Bluetooth connection remains active.
Note
• The music streaming may be interrupted by obstacles between the device and SoundBar, such as wall, metallic casing that covers the device, or other devices nearby that operate in the same frequency.
• If you want to connect your SoundBar with another
Bluetooth device, disable the currently connected
Bluetooth device.
• Philips does not guarantee 100% compatibility with all
Bluetooth devices.
10 EN
Auto standby
When playing media from a connected device, the SoundBar automatically switches to standby if:
• no source button is pressed for 30 minutes, and
• no audio/video playback is detected from a connected device.
Apply factory settings
You can reset your SoundBar to the default settings programmed at the factory.
1
Press TREBLE+, VOL-, and BASS+ within three seconds.
» When the factory settings restore is complete, the SoundBar automatically switches off and restarts.
EN 11
12 EN
5 Wall mount your SoundBar
Before you mount your SoundBar on the wall, read all safety precautions. (see 'Safety' on page
Wall mount
Note
• Koninklijke Philips Electronics N.V. bears no responsibility for improper wall mounting that results in accident, injury or damage. If you have any query, contact Philips Consumer Care in your country.
• Secure the wall mount to a wall that can support the combined weight of the product and the wall mount.
• Before wall mount, you need not remove the four rubber feet at the bottom of the soundbar, otherwise the rubber feet cannot be fixed back.
Screw length/diameter
Depend on the type of wall mounting this wall mount bracket, make sure that you use screws of a suitable length and diameter.
> 25mm
For information about how to wall your
SoundBar, see the wall mount guide.
3 - 3.5mm
6 Product specifications
Note
• Specifications and design are subject to change without notice.
Amplifier
• Total output power: 120W RMS (+/- 0.5 dB, 30% THD) / 96W RMS (+/- 0.5 dB,
10% THD)
• Frequency response: 20 Hz-20 kHz /
±3 dB
• Signal-to-noise ratio: > 65 dB (CCIR) /
(A-weighted)
• Input sensitivity:
• AUX: 800 mV
• Music iLink: 550 mV
Audio
• S/PDIF Digital audio input:
• Coaxial: IEC 60958-3
• Optical: TOSLINK
Bluetooth
• Bluetooth profiles: A2DP
• Bluetooth version: 2.1 + EDR
Main unit
• Power supply: 110-240 V~, 50-60 Hz
• Power consumption: 40 W
• Standby power consumption: ≤ 0.5 W
• Speaker impedance:
• Woofer: 3 ohm
• tweeter: 12 ohm
• Speaker drivers: 2 x 102 mm (4") woofer
+ 2 x 25.4 mm (1") tweeter
• Dimensions (WxHxD):
1010 x 81 x 154 mm
• Weight: 3.9 kg
Wall mount
• Dimensions (WxHxD):
40 x 100 x 26.5 mm
• Weight: 0.1 kg/each
Remote control batteries
• 2 x AAA-R03-1.5 V
EN 13
7 Troubleshooting
Warning
• Risk of electric shock. Never remove the casing of the product.
To keep the warranty valid, never try to repair the product yourself.
If you have problems using this product, check the following points before you request service.
If you still have a problem, get support at www.
philips.com/support.
Main unit
The buttons on the SoundBar do not work.
• Disconnect the SoundBar from the power supply for a few minutes, then reconnect.
Sound
No sound from SoundBar speakers.
• Connect the audio cable from your
SoundBar to your TV or other devices.
However, you do not need a separate audio connection when:
• the SoundBar and TV are connected through HDMI ARC connection, or
• a device is connected to the HDMI IN connector on your SoundBar.
• Reset your SoundBar to its factory settings
(see 'Apply factory settings' on page 11).
• On the remote control, select the correct audio input.
• Make sure that the SoundBar is not muted.
Distorted sound or echo.
• If you play audio from the TV through the
SoundBar, make sure that the TV is muted.
Audio and video are not synchronized.
• Press AUDIO SYNC +/- to synchronize the audio with the video.
14 EN
Bluetooth
A device cannot connect with the SoundBar.
• The device does not support the compatible profiles required for the
SoundBar.
• You have not enabled the Bluetooth function of the device. See the user manual of the device on how to enable the function.
• The device is not correctly connected.
Connect the device correctly. (see 'Play audio through Bluetooth' on page 10)
• The SoundBar is already connected with another Bluetooth device. Disconnect the connected device, then try again.
Quality of audio play from a connected
Bluetooth device is poor.
• The Bluetooth reception is poor. Move the device closer to the SoundBar, or remove any obstacle between the device and the
SoundBar.
The connected Bluetooth device connects and disconnects constantly.
• The Bluetooth reception is poor. Move the device closer to the SoundBar, or remove any obstacle between the device and the
SoundBar.
• Turn off Wi-Fi function on the Bluetooth device to avoid interference.
• For some Bluetooth, the Bluetooth connection can be deactivated automatically to save power. This does not indicate any malfunction of the SoundBar.
8 Notice
This section contains the legal and trademark notices.
Compliance
This product complies with the radio interference requirements of the European
Community.
Hereby, Philips Consumer Lifestyle, declares that this product is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
A copy of the EC declaration of Conformity is available in the Portable Document Format
(PDF) version of the user manual at www.
philips.com/support.
Trademarks
Manufactured under license under U.S.
Patent Nos: 5,956,674; 5,974,380; 6,487,535
& other U.S. and worldwide patents issued
& pending. DTS, the Symbol, & DTS and the
Symbol together are registered trademarks
& DTS Digital Surround and the DTS logos are trademarks of DTS, Inc. Product includes software. DTS, Inc. All Rights Reserved.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
The Bluetooth ® word mark and logos are registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Philips is under license.
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
EN 15
_
Philips Consumer Lifestyle
HK-1236- HTL5120/12
........................................................
(Report No. / Numéro du Rapport)
Year 2012
..............................................................................................
(Year in which the CE mark is affixed / Année au cours de laquelle le marquage CE a été apposé)
EC DECLARATION OF CONFORMITY
(DECLARATION DE CONFORMITE CE)
We / Nous, PHILIPS CONSUMER LIFESTYLE B.V.
(Name / Nom de l’entreprise)
TUSSENDIEPEN 4, 9206 AD DRACHTEN, THE NETHERLANDS
(address / adresse)
Declare under our responsibility that the electrical product(s):
(Déclarons sous notre propre responsabilité que le(s) produit(s) électrique(s):)
PHILIPS HTL5120/12
.................................. ...............................................
(Type version or model, référence ou modèle) (brand name, nom de la marque)
SOUNDBAR SPEAKER
.................................................................
( product description, description du produit)
To which this declaration relates is in conformity with the following harmonized standards:
(Auquel cette déclaration se rapporte, est conforme aux normes harmonisées suivantes)
(title, number and date of issue of the standard / titre, numéro et date de parution de la norme)
EN60065:2002+A1:2006+A11:2008+A2:2010+A12:2011
EN 55013:2001+A1: 2003+A2: 2006 EN 55020:2007+A11:2011
EN61000-3-2:2006+A1:2009+A2:2009 EN61000-3-3:2008
EN62301:2005 EN62311:2008
EN 300328 V1.7.1:2006 EN 301489-1 V1.9.2: 2011
EN 301489-17 V2.1.1: 2009
Following the provisions of :
(Conformément aux exigences essentielles et autres dispositions pertinentes de:)
1999/5/EC(R&TTE Directive)
2006/95/EC (Low Voltage Directive)
2004/108/EC (EMC Directive)
2011/65/EU (RoHS Directive)
2009/125/EC (ErP Directive)
- EC/1275/2008
And are produced under a quality scheme at least in conformity with ISO 9001 or CENELEC
Permanent Documents
(Et sont fabriqués conformément à une qualité au moins conforme à la norme ISO 9001 ou aux Documents Permanents CENELEC)
Telefication
The Notified Body ............................................... performed
(L’Organisme Notifié) (Name and number/ nom et numéro) ( a effectué)
NB
(certificate number / numéro du certificat)
(description of intervention /
description de l’intervention)
12214133/AA/00
And issued the certificate, ....................................................................................
(et a délivré le certificat)
Remarks:
(Remarques:)
Drachten, Netherlands, August 30, 2012
...........................................................
(place,date / lieu, date)
A.Speelman, CL Compliance Manager
...............................................................................................
(signature, name and function / signature, nom et fonction)
_
_
AMB 544-9056
16
Philips Consumer Lifestyle
Specifications are subject to change without notice
© 2013 Koninklijke Philips Electronics N.V.
All rights reserved.
HTL5120_12_UM_V3.0
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- 120 W Dolby Digital 5.1, DTS Digital Surround
- Audio Return Channel (ARC)
- Soundbar speaker RMS power: 120 W
- Active subwoofer
- Black
- Wired & Wireless Bluetooth