Philips docking station for iPod/iPhone DCB242

Register your product and get support at
DCB242
Important Safety Instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
2011 © Koninklijke Philips Electronics N.V. All rights reserved.
Specifications are subject to change without notice. Trademarks
are the property of Koninklijke Philips Electronics N.V. or their
respective owners. Philips reserves the right to change products at
any time without being obliged to adjust earlier supplies accordingly.
2
h Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
i Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
EN
User manual
Introduction
j Only use attachments/accessories specified by the
manufacturer.
With this unit, you can enjoy audio from the iPod, iPhone, other audio
devices, or the FM/DAB+ radio.
The radio, iPod, or iPhone can be set as the alarm timer. You can set two
alarm timers to go off at different time.
k Unplug this apparatus during lightning storms or when unused
for long periods of time.
What’s in the box
l Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
m Battery usage CAUTION – To prevent battery leakage which
may result in bodily injury, property damage, or damage to
the unit:
•
Install all batteries correctly, + and - as marked on the unit.
•
Do not mix batteries (old and new or carbon and alkaline,
etc.).
•
Remove batteries when the unit is not used for a long time.
d
f
g
n Apparatus shall not be exposed to dripping or splashing.
o Do not place any sources of danger on the apparatus (e.g.
liquid filled objects, lighted candles).
Warning
o n m l
© 2011 Koninklijke Philips Electronics N.V.
All rights reserved.
DCB242_79_UM_V1.0
Recycling
j i
h
Turn on the unit or switch to standby mode.
b REPEAT ALARM/BRIGHTNESS CONTROL
•
Repeat the alarm.
•
Adjust the display brightness.
c Dock for iPod/iPhone
•
Load an iPod/iPhone.
d SOURCE
•
Select a source: iPod/iPhone, DAB+/FM tuner, or MP3 link.
e FM antenna
•
Improve FM reception.
f MP3-LINK
•
Jack for an external audio device.
g DC 9V
•
Power supply socket.
EN
1
This product complies with the radio interference requirements of
the European Community.
Any changes or modifications made to this device that are not
expressly approved by Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
k
a
•
Notice
Important
Your product is designed and manufactured with high quality
materials and components, which can be recycled and reused.
When you see the crossed-out wheel bin symbol attached to a
product, it means the product is covered by the European Directive
2002/96/EC:
Safety
This ‘bolt of lightning’ indicates uninsulated material within your unit
may cause an electrical shock. For the safety of everyone in your
household, please do not remove product covering.
The ‘exclamation point’ calls attention to features for which you
should read the enclosed literature closely to prevent operating and
maintenance problems.
WARNING: To reduce the risk of fire or electric shock, this
apparatus should not be exposed to rain or moisture and objects
filled with liquids, such as vases, should not be placed on this
apparatus.
CAUTION: To prevent electric shock, match wide blade of plug to
wide slot, fully insert.
Never dispose of your product with other household waste. Please
inform yourself about the local rules on the separate collection of
electrical and electronic products. The correct disposal of your old
product helps prevent potentially negative consequences on the
environment and human health.
Your product contains batteries covered by the European Directive
2006/66/EC, which cannot be disposed of with normal household
waste.
Please inform yourself about the local rules on separate collection of
batteries. The correct disposal of batteries helps prevent potentially
negative consequences on the environment and human health.
Environmental information
All unnecessary packaging has been omitted. We have tried to make
the packaging easy to separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags, protective foam
sheet.)
Your system consists of materials which can be recycled and reused
if disassembled by a specialized company. Please observe the local
regulations regarding the disposal of packaging materials, exhausted
batteries and old equipment.
• Risk of explosion! Keep batteries away from heat, sunshine or fire.
Never discard batteries in fire.
g
o
h
n
m
i
l
j
For first-time use:
1 Remove the protective tab to activate the remote control
battery.
To replace the remote control batteries:
k
h OK/
•
Start or pause iPod/iPhone play.
•
Confirm selection.
i PRESET + /PRESET •
Select a preset radio station.
•
Navigate through the iPod/iPhone menu.
•
Adjust time.
j TUNING - /TUNING +
•
Skip to the previous/next audio file.
•
Search within an audio file.
•
Tune to a radio station.
•
Adjust time.
k Display panel
•
Show the current status.
l AL1/AL2
•
Set the alarm timer.
•
Turn off the alarm tone.
•
View alarm settings.
m VOL + /VOL •
Adjust volume.
n MENU
•
Select the iPod/iPhone menu.
•
Select the FM/DAB+ menu.
o SET TIME/AUTO SCAN /SLEEP
•
Set the clock and date.
•
Scan radio stations automatically.
•
Set the sleep timer.
1
Press POWER again to switch the unit to standby mode.
» The time and date (if set) appear on the display panel.
d PRESET + /PRESET •
Select a preset radio station.
•
Navigate through the iPod/iPhone menu.
•
Adjust time.
e TUNING - /TUNING +
•
Skip to the previous/next audio file.
•
Search within an audio file.
•
Tune to a radio station.
•
Adjust time.
3
Open the battery compartment.
Insert one lithium CR2025 battery with correct polarity (+/-) as
indicated.
Close the battery compartment.
select the correct source with the remote control instead of the
main unit.
the plug from the socket. Never pull the cord.
• Before connecting the AC adaptor, ensure that you have completed
1
DC 9V
Press iPod/iPhone on the remote control to select iPod/iPhone
source.
» The connected iPod/iPhone plays automatically.
.
•
To pause/resume play, press OK/
on
•
To skip to a track, press TUNING - /TUNING +
the remote control.
•
To search during play, press and hold TUNING - /
TUNING + , then release to resume normal play.
•
To go back to the previous iPod/iPhone menu, press
MENU. To scroll through the menu, press PRESET + /
.
PRESET - . To confirm a selection, press OK/
» If no key is pressed for more than 10 seconds, OK/
acts
back as the play/pause key.
DC 9V
1.9A
1.9A
When the unit is connected to power, the docked iPod/iPhone
begins to charge.
Tip
• For certain iPod models, it may take up to a minute before the
charging indication appears.
1
In standby mode, press and hold SET TIME/AUTO SCAN for 2
seconds.
» [SYNC ON] is displayed and [ON] begins to blink.
2
Press PRESET + /PRESET to select ON or OFF.
» If you select [ON], the unit reads the DAB+ or iPod/iPhone
time and sets the clock automatically.
» If you select [OFF], the unit turns off the time synchronization.
3
Press SET TIME/AUTO SCAN to confirm.The time format
[24H] or [12H] begins to blink.
Press PRESET + /PRESET to select 24H or 12H.
Press SET TIME/AUTO SCAN to confirm.The hour digits begin
to blink.
Repeat steps 4-5 to set the hour, minute, year, month, and day.
4
5
6
Note
Tip
3 x1.5V
LR6/UM-3/AA
3
Charge the iPod/iPhone
MP3-LINK
• Use of controls or adjustments or performance of procedures other
are for backup purpose.
Place the iPod/iPhone into the dock.
Connect the AC power adaptor to:
•
the DC socket on the main unit
•
the power socket.
Set time and date
• You can only use AC power as power supply. Batteries (not supplied)
2
• The type plate is located on the bottom of the main unit.
Get started
Install batteries
Lift up the iPod/iPhone dock cover on the top panel.
Note
o FM/DAB
•
Select the FM tuner/DAB+ source.
Always follow the instructions in this chapter in sequence.
If you contact Philips, you will be asked for the model and serial number
of this apparatus. The model number and serial number are on the rear
of the apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
1
all other connections.
• Use the supplied AC power adaptor only.
n SET TIME/AUTO SCAN
•
Set the time and date.
•
Scan radio stations automatically.
than herein may result in hazardous radiation exposure or other
unsafe operation.
Apple iPod and iPhone models with a 30-pin dock connector:
Made for.
•
iPod touch (1st, 2nd, 3rd, and 4th generation)
•
iPod classic
•
iPod with video
•
iPod nano (1st, 2nd, 3rd, 4th, 5th, and 6th generation)
•
iPod with color display
•
iPod mini
•
iPhone 4
•
iPhone 3GS
•
iPhone 3G
•
iPhone
to the voltage printed on the back or underside of the apparatus.
m REP AL/BRIGHTNESS
•
Adjust the display brightness.
•
Repeat the alarm.
Caution
Compatible iPod/iPhone
Caution
• Risk of electric shock! When you unplug the AC adaptor, always pull
3
You can enjoy audio from iPod/iPhone through this unit.
Connect power
i INFO
•
Select different types of DAB+ station information.
•
In FM mode, select RDS information.
l DBB
•
Turn on or off dynamic bass enhancement.
DSC
•
Select a preset sound setting.
Play from iPod/iPhone
• Before you press any function button on the remote control, first
• Risk of product damage! Ensure that the power voltage corresponds
k AL 1/AL 2
•
Set the alarm timer.
•
Turn off the alarm tone.
•
View alarm settings.
Play
Note
h iPod/iPhone
•
Select iPhone or iPod source.
j + VOL •
Adjust volume.
4
Listen to the iPod/iPhone
1
2
g MP3 LINK
•
Select external audio device source.
q Where the plug of the Direct Plug-in Adapter is used as the
disconnect device, the disconnect device shall remain readily
operable.
Never remove the casing of this apparatus.
Never lubricate any part of this apparatus.
Never place this apparatus on other electrical equipment.
Keep this apparatus away from direct sunlight, naked flames or heat.
Ensure that you always have easy access to the power cord, plug or
adaptor to disconnect the apparatus from the power.
f
f OK/
•
Start or pause iPod/iPhone play.
•
Confirm selection.
p Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the like.
•
•
•
•
•
e
c SLEEP
•
Set the sleep timer.
e
Switch to standby
Caution
b MENU
•
Select the iPod/iPhone menu.
Overview of the main unit
c
Prepare the remote control
d
a POWER
•
Turn on the unit or switch to standby mode.
Check and identify the contents of your package:
•
1 x Main unit
•
1 x Remote control
•
1 x Power adaptor
•
1 x MP3 link cable
•
1 x User manual
•
1 x Quick start guide
a b
Open the battery compartment.
Insert 3 x AA batteries with correct polarity (+/-) as indicated.
Close the battery compartment.
b
Your Docking Entertainment
System
Congratulations on your purchase, and welcome to Philips! To fully
benefit from the support that Philips offers, register your product at
www.philips.com/welcome.
1
2
3
a
c
f Clean only with dry cloth.
g Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
Overview of the remote control
• The accuracy of the transmitted time depends on the DAB+ station
or the docked iPod/iPhone that transmits the time signal.
Play from an external device
You can also listen to an external audio device through this unit.
1 Press MP3 LINK to select the MP3 link source.
2 Connect the supplied MP3 link cable to:
•
the MP3 LINK jack (3.5mm) on the back of the unit.
•
the headphone jack on an external device.
3 Start to play the device (see the device user manual).
5
Listen to radio
Listen to Digital Audio Broadcasts (DAB+)
Digital Audio Broadcasting (DAB+), is a way of broadcasting radio
digitally through a network of transmitters. It provides you with more
choice, better sound quality, and more information.
1 Press FM/DAB repeatedly to select DAB+.
» The unit automatically scans DAB+ radio stations. The unit
stores all available DAB+ radio stations and then broadcasts
the first available station.
» If no DAB+ service is available, [NO SERV] is displayed.
Turn on
Scan DAB+ radio stations automatically
1
You can perform full scan to search for DAB+ radio stations.
1 In DAB+ mode, press and hold SET TIME/AUTO SCAN for
more than 3 seconds.
Press POWER on the remote control.
» The unit switches to the last selected source.
» The unit scans all available DAB+ radio stations and
broadcasts the first available station.
» The radio tunes to a station with strong reception
automatically.
3
Program DAB+ radio stations manually
1
2
3
4
5
Tune to a DAB+ radio station.
Press SET TIME/AUTO SCAN to activate the program mode.
Press TUNING - /TUNING +
to select a number.
Press SET TIME/AUTO SCAN to confirm.
Repeat the above steps to program other stations.
Note
• To overwrite a programmed station, store another station in its
place.
2
In DAB+ mode, press TUNING DAB+ radio station.
Press OK/
to confirm.
Program radio stations automatically
You can program a maximum of 20 preset radio stations.
1 In the tuner mode, press and hold SET TIME/AUTO SCAN for
more than 2 seconds to activate automatic program mode.
» The unit starts to search for radio stations.
» All available stations are programmed in the order of
waveband reception strength.
» The first programmed radio station is broadcast automatically.
This unit can switch to standby automatically after a set period of time.
1 Press SLEEP repeatedly to select a set period of time (in
minutes).
» When the sleep timer is activated, the display shows .
To deactivate sleep timer
1 Press SLEEP repeatedly until [OFF] (off ) is displayed.
disappears on the
» When the sleep timer is deactivated,
display.
Adjust display brightness
1
Press REP AL/BRIGHTNESS repeatedly to select different
levels of display brightness.
Program FM radio stations manually
Listen to a preset DAB+ radio station
1
Repeat step 2 to tune to more stations.
•
To tune to a weak station, press TUNING - /TUNING
repeatedly until you find optimal reception.
+
9
Set the sleep timer
/TUNING +
to select a
Note
You can program a maximum of 20 preset radio stations.
1 Tune to a radio station.
2 Press SET TIME/AUTO SCAN to activate the program mode.
3 Press TUNING - /TUNING + to select a number.
4 Press SET TIME/AUTO SCAN to confirm.
5 Repeat the above steps to program other stations.
7
Adjust sound
During play, press + VOL - to increase/decrease the volume
level.
• If there is no DAB+ radio station available, steps mentioned above
is invalid.
Tip
Select a preset sound effect
• To overwrite a programmed station, store another station in its
Show DAB+ information
1
During listening to DAB+ radio, press INFO repeatedly to
scroll through the following information (if available):
» Dynamic Label Segment (DLS)
» Signal strength
» Program type (PTY)
» Ensemble Name
» Channel and frequency
» Signal error rate
» Bit rate and audio status
» Date
Perform more functions through DAB+ menu
1
2
3
4
In DAB+ mode, press and hold MENU to enter the DAB+
menu.
Press TUNING - /TUNING +
to select:
•
[MANUAL] (tune manually)
•
[SCAN] (tune automatically)
•
[DRC] (dynamic range control)
•
[TUNERRST] (tuner reset)
•
[VERSION] (display software version)
If you select [DRC], press OK/
to confirm, and then press
to select:
TUNING - /TUNING +
•
[DRC 0]: Dynamic Range Control is switched off.
•
[DRC 1/2]: Dynamic Range Control is set to half normal
level.
•
[DRC 1]: Dynamic Range Control is switched on; the
default setting recommended for noisy environment.
Press OK/
to confirm.
To reset the tuner:
1 Follow steps 1-2 above to select [TUNERRST].
2 Press OK/ to confirm, and then press TUNING to select:
TUNING +
•
[NO]: Cancel.
•
[YES]: Reset the tuner.
3 Press OK/ to confirm.
Listen to a preset radio station
1
/PRESET -
to select a
6
1
2 x 5 W RMS
20 -20000 Hz, -3dB
3
4
Press TUNING - /TUNING +
to set the hour.
Press AL1 or AL2 to confirm.
» The [AL1] or [AL2] icon and the minute digits begin to blink.
5
6
Repeat steps 3-4 to set the minute.
Repeat steps 3-4 to select whether to ring alarm the whole
week, on weekdays, or at weekend.
Repeat steps 3-4 to select an alarm sound source: Buzzer,
iPhone, FM, or DAB+.
Repeat steps 3-4 to set the alarm volume.
Turn on/off the alarm timer
Signal to Noise Ratio
>67 dB
Total Harmonic Distortion
<1%
Aux Input (MP3 link)
0.5 V RMS 20 kohm
Tuning range
87.5 - 108 MHz
Tuning grid
50 KHz
Sensitivity
- Mono, 26dB S/N Ratio
- Stereo, 46dB S/N Ratio
<22 dBu
<43 dBu
Search Selectivity
>28 dBf
Total Harmonic Distortion
<2%
Signal to Noise Ratio
>55 dB
Tuner (DAB+)
DAB+ tuning range
1
Press AL1/AL2 to turn on or off the alarm timer.
» If the alarm timer is turned on, the alarm icon appears.
» If the alarm timer is turned off, the alarm icon disappears.
When the alarm rings, press REP AL/BRIGHTNESS.
» The alarm repeats ringing minutes later.
Tip
• Position the antenna as far as possible from TV, VCR or other
radiation source.
• For optimal reception, do not place iPod/iPhone into the dock when
• You can press TUNING -
you listen to the radio.
/TUNING +
to adjust interval (5-30
minutes) to repeat alarm.
Stop alarm ring
Note
• For optimal reception, fully extend and adjust the position of the
1
antenna.
When the alarm rings, press the corresponding AL1 or AL2.
» The alarm stops but the alarm settings remain.
View the alarm settings
for more than 2
1
Press AL1 or AL2.
Poor radio reception
•
Increase the distance between the unit and your TV or VCR.
•
Fully extend the FM antenna.
Timer does not work
•
Set the clock correctly.
•
Switch on the timer.
Clock/timer setting erased
•
Power has been interrupted or the power plug has been
disconnected.
•
Reset the clock/timer.
Notes
Tuner (FM)
• Ensure that you already set the alarms successfully.
Tip
No response from the unit
•
Disconnect and reconnect the AC power plug, then turn on the
unit again.
Amplifier
174.92 - 239.20 MHz
General information
AC power (Power adaptor)
Repeat alarm
Tune to a radio station
No power
•
Ensure that the AC power plug of the unit is connected
properly.
•
Ensure that there is power at the AC outlet.
•
Ensure that the batteries are inserted correctly.
• Product information is subject to change without prior notice.
Frequency Response
1
To keep the warranty valid, never try to repair the system yourself.
If you encounter problems when using this apparatus, check the
following points before requesting service. If the problem remains
unsolved, go to the Philips web site (www.philips.com/welcome). When
you contact Philips, ensure that the apparatus is nearby and the model
number and serial number are available.
Note
Rated Output Power
Listen to FM radio
Press FM/DAB to select FM tuner.
Press and hold TUNING - /TUNING +
seconds.
Product information
You can set two alarms which go off at different time.
1 Ensure that you have set the clock correctly. (See “Get started Set time and date”.)
2 Press and hold AL1 or AL2 for 2 seconds.
» The [AL1] or [AL2] icon and the hour digits begin to blink.
7
• Never remove the casing of this apparatus.
Specifications
Other features
Note
compensation for the differences in the dynamic range between
radio stations.
8
During play, press DBB to turn on or off dynamic bass
enhancement.
» If DBB is activated, [DBB] is displayed.
Set the alarm timer
Tip
• Dynamic range control (DRC) adds or removes a degree of
During play, press DSC repeatedly to select:
•
[POP] (pop)
•
[CLASSIC] (classic)
•
[JAZZ] (jazz)
•
[FLAT] (flat)
•
[ROCK] (rock)
Enhance bass
RDS (Radio Data System) is a service that allows FM stations to
show additional information. If you tune to a RDS station, the station
name is displayed.
1 Tune to a RDS station.
2 Press INFO repeatedly to scroll through the following
information (if available):
» Station name
» Radio text messages
» Program type such as [NEWS] (news(, [SPORT] (sport),
[POP M] (pop music)...
» Frequency
8
• If no button is pressed within 10 seconds, the menu exits.
In tuner mode, press PRESET +
preset number.
Show RDS information
/
Note
1
2
1
place.
Warning
No sound
•
Adjust the volume.
Adjust volume level
1
Troubleshooting
Input: 100-240V~, 50/60Hz, 0.7A;
1.9A; Brand
Output: 9.0V
name: Philips; Model No.: AS190090-BM19
Operation Power
Consumption
15 W
Standby Power Consumption
<1 W
Dimensions
- Main Unit (W x H x D)
280 x 82 x 170 mm
Weight
- Main Unit
1.09 kg
Notes
Notes