advertisement
Register your product and get support at
www.philips.com/welcome
DCM2060
EN User manual
DCM2060_79_UM_V1.0.indd 1 6/1/2012 10:53:45 AM
Contents
Overview of the remote control
Auto install FM radio stations
Program FM radio stations automatically 13
Program FM radio stations manually
Play from external audio device
EN 3
6/1/2012 10:53:45 AM DCM2060_79_UM_V1.0.indd 3
1 Important
• Read these instructions.
• Follow all instructions.
• Do not block any ventilation openings.
Install in accordance with the manufacturer's instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the unit.
• Only use attachments/accessories specified by the manufacturer.
• Unplug this unit during lightning storms or when unused for long periods of time.
• Refer all servicing to qualified service personnel. Servicing is required when the unit has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the unit has been exposed to rain or moisture, does not operate normally, or has been dropped.
• Battery usage CAUTION – To prevent battery leakage which may result in bodily injury, property damage, or damage to the remote control:
• Install all batteries correctly, + and - as marked on the remote control.
• Do not mix batteries (old and new or carbon and alkaline, etc.).
• Remove batteries when the remote control is not used for a long time.
• The unit shall not be exposed to dripping or splashing.
• Do not place any sources of danger on the unit (e.g. liquid filled objects, lighted candles).
• Where the plug of the Direct Plug-in
Adapter is used as the disconnect device, the disconnect device shall remain readily operable.
Warning
• Never remove the casing of this apparatus.
• Never place this apparatus on other electrical equipment.
• Never look into the laser beam inside this apparatus.
• Ensure that you always have easy access to the power cord, plug or adaptor to disconnect the apparatus from the power.
Hearing Safety
Danger
• To avoid hearing damage, limit the time you use the headphones at high volume and set the volume to a safe level. The louder the volume, the shorter is the safe listening time.
Be sure to observe the following guidelines when using your headphones.
• Listen at reasonable volumes for reasonable periods of time.
• Be careful not to adjust the volume continuously upwards as your hearing adapts.
• Do not turn up the volume so high that you can’t hear what’s around you.
• You should use caution or temporarily discontinue use in potentially hazardous situations.
• Excessive sound pressure from earphones and headphones can cause hearing loss.
Caution
• Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.
4 EN
DCM2060_79_UM_V1.0.indd 4 6/1/2012 10:53:45 AM
2 Your Micro
System
Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.
Introduction
With this unit, you can:
• enjoy audio from discs, iPod/iPhone/iPad,
USB devices, and other external devices
• listen to FM radio
You can enrich sound output with these sound effects:
• Digital Sound Control (DSC)
• Dynamic Bass Boost (DBB)
The unit supports these media formats:
What's in the box
Check and identify the contents of your package:
• Main unit
• Remote control
• Power adapter
• 1 x MP3 link cable
• Mounting kit (2 dowels and 2 screws)
• FM antenna
• Rubber pad for iPad
• User manual
• Quick start guide
• Wall mounting instructions
If you contact Philips, you will be asked for the model and serial number of this apparatus. The model number and serial number are on the bottom of the apparatus. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
EN 5
6/1/2012 10:53:46 AM DCM2060_79_UM_V1.0.indd 5
DCM2060_79_UM_V1.0.indd 6
6 EN a b c d e f k l a b c
Overview of the main unit
2
FM NT
V A
• Connect USB device.
• Headphone socket.
SOURCE
• Turn the unit on.
• Switch to standby mode.
d SOURCE
• Select a source: CD, FM, USB, Dock, or
MP3 LINK.
OK / MENU
MP 3 L
MICRO MUSIC SYSTEM DCM2060
VOLUME
D CK f
VOLUME f OK/
• Confirm selection.
• Switch between mono and stereo broadcast.
• Start or pause play.
g MP3-LINK
• Connect an external audio device.
h
• Open or close the disk tray.
i VOLUME + / -
• Adjust volume.
e /
• Skip to the previous or next track.
• Search within a track or disc.
• Tune to radio stations.
• Adjust time.
g h i j m n o j MENU/
• Access iPod/iPhone menu.
• Stop play or erase a program.
k FM ANT
• Improve FM reception.
l DC IN
• Connect power.
6/1/2012 10:53:49 AM
s r q
PRESET/ALBUM n Disc tray o DOCK for iPod/iPhone/iPad m Display panel
• Show play information.
Overview of the remote control a b c d e f g h i j k l
CD
MP3 LINK
USB
DISPLAY
RDS
1
4
7
PROG/
CLOCK SET
SLEEP/
TIMER
DCM2060_79_UM_V1.0.indd 7
OK
VOL
2
5
8
0
DSC
MENU
3
6
9
FM
DOCK
REPEAT/
SHUFFLE
DBB p o n m a
• Turn the unit on.
• Switch to standby mode.
b
• Mute or restore sound.
c CD
• Select CD source.
d /
• Skip to the previous or next track.
• Search within a track or disc.
• Tune to radio stations.
• Adjust time.
e USB/MP3 LINK
• Select USB or MP3 link source.
f RDS/DISPLAY
• Show time and play information.
• Have no RDS function.
g
• Start/pause play.
h VOL +/-
• Adjust volume.
i Numeric Keypad 0 - 9
• Select a track from a disc or USB device directly.
• Select a preset radio station.
j PROG/CLOCK SET
• Program tracks.
• Program radio stations.
• Set time.
k SLEEP/TIMER
• Set sleep or alarm timer.
l DSC
• Select a preset sound setting.
m DBB
• Turn dynamic bass enhancement on or off.
EN 7
6/1/2012 10:53:50 AM
n REPEAT/SHUFFLE
• Play a track or all tracks repeatedly.
• Play tracks in current album repeatedly.
• Play tracks randomly.
o MENU/
• Access iPod/iPhone menu.
• Stop play or erase a program.
p DOCK
• Select iPod/iPhone/iPad source.
q OK
• Confirm selection.
• Switch between mono and stereo broadcast.
r /
• Select a preset radio station.
• Skip to the previous or next album.
s FM
• Select FM tuner source.
3 Get started
Always follow the instructions in this chapter in sequence.
Placement
You can place the unit on a flat surface or mount the unit on a wall.
Mount on a wall
See the wall mounting instructions included in the package.
Connect FM antenna
Tip
Connect the supplied FM antenna to the FM
ANT socket on the main unit.
• For optimal reception, fully extend and adjust the position of the antenna.
8 EN
DCM2060_79_UM_V1.0.indd 8 6/1/2012 10:53:51 AM
DCM2060_79_UM_V1.0.indd 9
Prepare the remote control
Caution b
• Risk of explosion! Keep batteries away from heat, sunshine or fire. Never discard batteries in fire.
• Risk of decreased battery life! Never mix different brands or types of batteries.
• Risk of product damage! When the remote control is not used for long periods, remove the batteries.
To install the remote control battery:
1
Open the battery compartment.
2
Insert 2 AAA batteries with correct polarity (+/-) as indicated.
3
Close the battery compartment.
a c
Connect power
Caution
• Risk of product damage! Ensure that the power supply voltage corresponds to the voltage printed on the back or the underside of the unit.
• Risk of electric shock! When you unplug the AC power adapter, always pull the plug from the socket. Never pull the cord.
• Before connecting the AC adapter, ensure that you have completed all other connections.
Note
Connect the power adapter to:
• the DC IN socket on the main unit.
• the wall socket.
• The type plate is located at the back of the main unit.
EN 9
6/1/2012 10:53:52 AM
DCM2060_79_UM_V1.0.indd 10
10 EN
4 Play
Turn on
Press .
» The unit switches to the last selected source.
Note
• To select a source, press SOURCE repeatedly or the source selection buttons on the remote control.
Switch to standby mode
Press again to switch the unit to standby mode.
» The clock (if set) appears on the display panel.
Set clock
1
In standby mode, press and hold CLOCK
SET on the remote control for two seconds.
» [SET CLOCK] (set clock) scrolls on the display.
2
Press CLOCK SET again.
» The 12 or 24 hour format blinks.
3
Press / repeatedly to select an hour format.
4
Press CLOCK SET to confirm.
» The hour digits blink.
5
Repeat steps 3-4 to set the hour and minute respectively.
Note
• If the system is idle for 90 seconds, the unit exits clock setting mode automatically.
Play disc
1
Press to open the disc compartment.
2
Insert a disc with the printed side facing up.
3
Press to close the disc compartment.
4
Press CD on the remote control to select the disc source.
» [Reading] (reading) blinks for a moment, then CD starts playing automatically. If not, press .
Play from USB
• Make sure that the USB device contains playable audio content.
Note
1
Insert the USB device into the socket.
2
Press USB on the remote control to select the USB source.
» Play starts automatically. If not, press
.
6/1/2012 10:53:53 AM
DCM2060_79_UM_V1.0.indd 11
Play from iPod/iPhone/iPad
You can enjoy audio from iPod/iPhone/iPad through this unit.
Compatible iPod/iPhone/iPad
The unit supports the following iPod, iPhone and iPad models:
Made for.
• iPod touch (1st, 2nd, 3rd, and 4th generation)
• iPod nano (2nd, 3rd, 4th, 5th, and 6th generation)
• iPhone 4
• iPhone 3GS
• iPhone 3G
• iPhone
• iPad 2
• iPad
Load the iPod/iPhone/iPad
1
Push the dock compartment to open it.
2
Place the iPod/iPhone/iPad in the dock.
Install the rubber pad
If necessary, install the supplied rubber pad to keep the iPad/iPad 2 stable before you place the iPad/iPad 2.
Listen to the iPod/iPhone/iPad
Note
• Make sure that the iPod/iPhone/iPad is loaded correctly.
1
Press SOURCE repeatedly or DOCK on the remote control to select iPod/iPhone/ iPad source.
2
Play tracks on the iPod/iPhone/iPad.
• To pause/resume play, press .
• To skip to a track, press / .
• To search during play, press and hold
/ , then release to resume normal play.
• To go back to the previous iPod/ iPhone menu, press MENU.
• To scroll through the menu, press / .
• To confirm a selection, press OK.
Remove the iPod/iPhone/iPad
Pull the iPod/iPhone/iPad out of the dock.
Charge the iPod/iPhone/iPad
Note
• iPod with color display, iPod classic, and iPod with video are not compatible with dock charging.
When the unit is connected to power, the docked iPod/iPhone/iPad begins to charge.
EN 11
6/1/2012 10:53:55 AM
Tip
• For certain iPod models, it may take up to a minute before the charging indication appears.
Play options
Pause/resume play
During play, press to pause or resume play.
Repeat/shuffle play
1
During play, press REPEAT/SHUFFLE repeatedly to select:
• : play the current track repeatedly.
•
•
•
(for MP3/WMA only): play all tracks in this album repeatedly.
: play all tracks repeatedly.
: play all tracks randomly.
2
To resume normal play, press
REPEAT/SHUFFLE repeatedly until the above icons disappear.
Skip to a track
For CD:
Press / to select another track.
For MP3 disc and USB:
1
Press / to select an album or a folder.
2
Press / to select a track/file.
Tip
• To select a track directly, you can also press a key on the numerical keypad.
Search within a track
1
During play, press and hold / .
2
Release to resume normal play.
Program tracks
You can program a maximum of 20 tracks.
1
In CD/USB mode, press to stop playback, then press PROG to activate the programming mode.
» [PROG] (program) is displayed.
2
For MP3/WMA tracks, press / to select an album.
3
Press / to select a track, then press
PROG to confirm.
4
Repeat steps 2 to 3 to program more tracks.
5
Press to play the programmed tracks.
» During play, [PROG] (program) is displayed.
• To erase the program, when playback is stopped, press .
Adjust sound
During play, you can adjust volume and select sound effects.
Function
To turn dynamic bass enhancement on/off
Action
To increase or decrease volume Press VOL +/-.
To mute or restore sound Press .
Press DBB.
To select a sound effect:
[POP] (pop)
[JAZZ] (jazz)
[CLASSIC] (classic)
[ROCK] (rock)
[FLAT] (flat)
Press DSC repeatedly.
Display different information
During play, press DISPLAY repeatedly to view time and different play information.
12 EN
DCM2060_79_UM_V1.0.indd 12 6/1/2012 10:53:57 AM
5 Listen to FM radio
Auto install FM radio stations
When the unit turns to FM tuner mode, and no radio stations are stored, the unit prompts you to search and store all the available FM stations.
Note
• Position the antenna as far as possible from TV, VCR, or other radiation source.
• Ensure that you have connected and fully extended the supplied FM antenna.
1
Press FM to select FM tuner mode.
» [AUTO INSTALL - PRESS PLAY, STOP
CANCEL] (to auto install, press ; to cancel, press ) is displayed.
2
Press and hold for 3 seconds to start full scan.
» The unit automatically stores FM radio stations with sufficient signal strength and then broadcasts the first preset station.
Tip
• To exit storing mode, press or .
• RDS function is not available.
Tune to FM radio stations
1
In FM tuner mode, press and hold / for 3 seconds.
» [SEARCH] (search) is displayed.
» The unit tunes to an FM station with strong reception automatically.
2
Repeat step 1 to tune to more stations.
To tune to a station with weak signal
Press / repeatedly until you find optimal reception.
Program FM radio stations automatically
Note
• You can program a maximum of 20 preset FM radio stations.
In FM tuner mode, press and hold PROG for 3 seconds.
» [AUTO] (auto) is displayed.
» The unit stores all the FM radio stations automatically and then broadcasts the first preset radio station.
Program FM radio stations manually
1
In tuner mode, tune to an FM radio station.
2
Press PROG to activate programming mode.
» [PROG] (program) blinks.
3
Press / repeatedly to select a channel number.
4
Press PROG again to confirm.
5
Repeat steps 1-4 to store other FM stations.
Note
• To remove a pre-stored station, store another station in its place.
EN 13
DCM2060_79_UM_V1.0.indd 13 6/1/2012 10:53:57 AM
Select a preset radio station
In tuner mode, press / or the numeric buttons to select a radio station.
Select stereo/mono broadcast
Note
• Stereo broadcast is the default setting for tuner mode.
• For stations with weak signals: to improve the reception, change to monaural sound.
In FM tuner mode, press OK to switch between mono and stereo broadcast.
6 Other features
Set the alarm timer
This unit can be used as an alarm timer. You can select CD, FM tuner, iPod/iPhone/iPad, or USB as alarm source.
Note
• Make sure that you have set the clock correctly.
1
In standby mode, press and hold TIMER until [SET TIMER] (set timer) scrolls on the display.
» [SELECT SOURCE] (select source) is displayed.
2
Press SOURCE repeatedly or the source selection buttons on the remote control to select a source: disc, FM tuner, iPod/iPhone/ iPad, or USB.
3
Press TIMER to confirm.
» The hour digits blink.
4
Press / repeatedly to set the hour.
5
Press TIMER to confirm.
» The minute digits blink.
6
Repeat steps 4-5 to set the minute and alarm volume.
Note
• If the system is idle for 90 seconds, the unit exits alarm setting mode automatically.
• If iPod/iPhone/iPad is selected as alarm source, and you have created a playlist called "PHILIPS" in iTunes and import it to your iPod/iPhone/iPad, you will wake to a random track in the playlist.
• If no "PHILIPS" playlist is created in the iPod/iPhone/iPad or no track is stored in the playlist, you will wake to your last listened track in the iPod/iPhone/iPad.
14 EN
DCM2060_79_UM_V1.0.indd 14 6/1/2012 10:53:58 AM
To activate or deactivate the alarm timer
In standby mode, press TIMER repeatedly to activate or deactivate the alarm.
» appears when the timer is activated.
Tip
• If CD/USB/iPod source is selected, while the audio cannot be played, the unit switches to the tuner source automatically.
7 Product information
Note
• Product information is subject to change without prior notice.
Set the sleep timer
Note
• Make sure that you have set the clock correctly.
When the unit is turned on, press SLEEP repeatedly to select the sleep timer period (in minutes).
» When sleep timer is activated, is displayed.
To deactivate the sleep timer
Press SLEEP repeatedly until [OFF] (off) is displayed.
Listen through the headphone
Plug a headphone into the socket on the unit.
Play from external audio device
With this unit, you can play audio from an external audio device like MP3 player.
1
Connect the supplied MP3 Link cable to
• the MP3-LINK socket.
• the audio output socket of an external device.
2
Press USB/MP3 LINK repeatedly to select
MP3 link mode.
3
Start to play the external device (see the device's user manual).
Specifications
Amplifier
Rated Output Power
Frequency Response
Signal to Noise Ratio
MP3 Link Input
2 X 10 W RMS
80 Hz - 16 kHz,
± 3 dB
≥60 dB
0.5 V RMS 20 kohm
Disc
Laser Type
Disc Diameter
Support Disc
Audio DAC
Total Harmonic
Distortion
Frequency Response
S/N Ratio
Semiconductor
12 cm/8 cm
CD-DA, CD-R,
CD-RW, MP3-CD,
WMA-CD
24 Bits/44.1 kHz
<1 5 % (1 kHz)
60 Hz - 16 kHz
>55 dBA
Tuner (FM)
Tuning range
Tuning grid
Sensitivity
- Mono, 26dB S/N Ratio
- Stereo, 46dB S/N Ratio
87.5 - 108 MHz
50 KHz
<22 dBf
<43 dBf
EN 15
DCM2060_79_UM_V1.0.indd 15 6/1/2012 10:53:58 AM
Search selectivity >28 dBf
Total harmonic distortion <3%
Signal to noise ratio >50 dB
Number of presets 20
General information
AC power
Operation Power
Consumption
Standby Power
Consumption
Dimensions
- Main Unit
(W x H x D)
Weight (Main Unit)
Model: AS360-120-
AM300;
Input: 100 - 240 V ~,
50/60 Hz, 1.2 A;
Output: 12 V 3.0 A
25 W
≤1 W
400 x 235 x 98 mm
2.2 kg
USB playability information
Compatible USB devices:
• USB flash memory (USB1.1)
• USB flash players (USB1.1)
• memory cards (requires an additional card reader to work with this unit)
Supported formats:
• USB or memory file format: FAT12, FAT16,
FAT32 (sector size: 512 bytes)
• MP3 bit rate (data rate): 32-320 Kbps and variable bit rate
• WMA v9 or earlier
• Directory nesting up to a maximum of 8 levels
• Number of albums/ folders: maximum 99
• Number of tracks/titles: maximum 999
• ID3 tag v2.0 or later
• File name in Unicode UTF8 (maximum length: 16 bytes)
Unsupported formats:
• Empty albums: an empty album is an album that does not contain MP3/WMA files, and is not be shown in the display.
• Unsupported file formats are skipped. For example, Word documents (.doc) or MP3 files with extension .dlf are ignored and not played.
• AAC, WAV, PCM audio files
• DRM protected WMA files (.wav, .m4a,
.m4p, .mp4, .aac)
• WMA files in Lossless format
Supported MP3 disc formats
• ISO9660, Joliet
• Maximum title number: 999 (depending on file name length)
• Maximum album number: 99
• Supported sampling frequencies: 32 kHz,
44.1 kHz, 48 kHz
• Supported Bit-rates: 32~320 (kbps), variable bit rates
16 EN
DCM2060_79_UM_V1.0.indd 16 6/1/2012 10:53:59 AM
8 Troubleshooting
Warning
• Never remove the casing of this apparatus.
To keep the warranty valid, never try to repair the system yourself.
If you encounter problems when using this apparatus, check the following points before requesting service. If the problem remains unsolved, go to the Philips web site
(www.philips.com/support). When you contact
Philips, ensure that the apparatus is nearby and the model number and serial number are available.
No power
• Ensure that the AC power adapter of the unit is connected properly.
• Ensure that there is power at the AC outlet.
• As a power-saving feature, the system switches off automatically 15 minutes after track play reaches the end and no control is operated.
No sound
• Adjust the volume.
No response from the unit
• Disconnect and reconnect the AC power plug, then turn on the unit again.
• As a power-saving feature, the system switches off automatically 15 minutes after track play reaches the end and no control is operated.
Remote control does not work
• Before you press any function button, first select the correct source with the remote control instead of the main unit.
• Reduce the distance between the remote control and the unit.
• Insert the battery with its polarities (+/– signs) aligned as indicated.
• Replace the battery.
• Aim the remote control directly at the sensor on the front of the unit.
No disc detected
• Insert a disc.
• Check if the disc is inserted upside down.
• Wait until the moisture condensation at the lens has cleared.
• Replace or clean the disc.
• Use a finalized CD or correct format disc.
Cannot display some files in USB device
• The number of folders or files in the USB device has exceeded a certain limit. This phenomenon is not a malfunction.
• The formats of these files are not supported.
USB device not supported
• The USB device is incompatible with the unit. Try another one.
Poor radio reception
• Increase the distance between the unit and your TV or VCR.
• Fully extend the FM antenna.
Timer does not work
• Set the clock correctly.
• Switch on the timer.
Clock/timer setting erased
• Power has been interrupted or the power cord has been disconnected.
• Reset the clock/timer.
EN 17
DCM2060_79_UM_V1.0.indd 17 6/1/2012 10:53:59 AM
9 Notice
Any changes or modifications made to this device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s authority to operate the equipment.
This product complies with the radio interference requirements of the European Community.
Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/EC.
Please inform yourself about the local separate collection system for electrical and electronic products.
Please act according to your local rules and do not dispose of your old products with your normal household waste. Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health.
Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed with normal household waste.Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health.
18 EN
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment.
The making of unauthorized copies of copyprotected material, including computer programs, files, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal offence.
This equipment should not be used for such purposes.
“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet
Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance.
iPod and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. iPad is a trademark of Apple Inc.
This apparatus includes this label:
DCM2060_79_UM_V1.0.indd 18 6/1/2012 10:54:00 AM
Philips Electronics Australia Limited and Philips New Zealand Limited
Warranty against Defects
In this warranty:
We or us means Philips Electronics Australia Limited ACN 008 445 743 or Philips New Zealand Limited (Company
Number 1723), and our contact details are set out at the end of this warranty;
You means the purchaser or the original end-user of the Goods;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods in Australia or New
Zealand; and
Goods means the product or equipment which was accompanied by this warranty and purchased in Australia or New
Zealand.
If you require assistance with the operation of the product, its features or specifications please call the Philips
Consumer Care Centre on 1300 363 391 in Australia or 0800 658 224 in New Zealand.
Australia: Our Goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the Goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. This is not a complete statement of your legal rights as a consumer.
New Zealand: Our Goods come with guarantees that cannot be excluded under the Consumer Guarantees Act 1993.
This guarantee applies in addition to the conditions and guarantees implied by that legislation.
Additional Warranty:
In addition to the rights and remedies that you have under the Australian Consumer Law, Consumer Guarantees Act of New Zealand or any other applicable law, we provide the following warranty against defects:
1. If, during the first 12 months from their date of purchase from the Supplier (Warranty Period), the Goods prove defective by reason of improper workmanship or materials and none of your statutory rights or remedies apply, we will repair or replace the Goods without charge.
2. We do not have to repair or replace the Goods under this Additional Warranty if the Goods have been used for a commercial purpose; misused, improperly or inappropriately installed, operated or repaired; abused; damaged; or not maintained in accordance with the manufacturer’s instructions.
3. Even when we do not have to repair or replace the Goods, we may decide to do so anyway. In some cases, we may decide to substitute the Goods with a similar alternative product of our choosing. All such decisions are at our absolute discretion.
4. All such repaired, replaced or substituted Goods continue to receive the benefit of this Additional Warranty for the time remaining on the original Warranty Period.
5. This Additional Warranty is limited to repair, replacement or substitution only. As far as the law permits, we will not be liable for any loss or damage caused to property or persons arising from any cause whatsoever.
6. In order to claim under this Additional Warranty you must telephone us on 1300 363 391 in Australia or 0800 658
224 in New Zealand within the Warranty Period. You will be asked for details of the Goods, a description of the defect and your personal details. Upon accepting your claim, we shall assist you with either returning the Goods to the Supplier for replacement or to the most convenient Philips Authorised Service Centre for your Goods to be repaired. In some case we may require that you return to the Goods to us (at the address below) for repair, replacement or substitution.
∗ All returned Goods must be accompanied by satisfactory proof of purchase which clearly indicates the name and address of the Supplier, the date and place of purchase and identifies product. It is best to provide a legible and unmodified receipt or sales invoice.
∗ You must bear any expense for return of the Goods or otherwise associated with making your claim under this
Additional Warranty.
7. This warranty is only valid and enforceable in Australia and New Zealand.
Contact us or the place of purchase for further details.
Philips Electronics Australia Limited
Level Rd,
Philips New Zealand Limited
Level
North
E-mail: [email protected]
Website:
SYDNEY
363 www.philips.com/support
Email:
Website: www.philips.com/support
19
DCM2060_79_UM_V1.0.indd 19 6/1/2012 10:54:01 AM
Specifications are subject to change without notice
© 2012 Koninklijke Philips Electronics N.V.
All rights reserved.
DCM2060_79_UM_V1.0
DCM2060_79_UM_V1.0.indd 20 6/1/2012 10:54:01 AM
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Dock for iPod/iPhone/iPad
Related manuals
Frequently Answers and Questions
How do I set the clock on my Philips DCM2060?
How do I play a CD on my Philips DCM2060?
How do I play music from a USB device on my Philips DCM2060?
How do I listen to the radio on my Philips DCM2060?
How do I connect my iPod/iPhone/iPad to my Philips DCM2060?
advertisement