filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\01COV.fm]
masterpage:Cov
4-487-569-12(1)
HOME AUDIO
SYSTEM
Operating Instructions
Getting Started
Disc/USB Playback
USB Transfer
Tuner
Bluetooth
Sound Adjustment
Other Operations
Additional Information
SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\020REG.fm]
WARNING
To reduce the risk of fire or electric
shock, do not expose this apparatus
to rain or moisture.
To reduce the risk of fire, do not cover the
ventilation opening of the appliance with
newspapers, tablecloths, curtains, etc.
Do not expose the appliance to naked flame
sources (for example, lighted candles).
To reduce the risk of fire or electric shock, do
not expose this appliance to dripping or
splashing, and do not place objects filled
with liquids, such as vases, on the appliance.
As the main plug is used to disconnect the
unit from the mains, connect the unit to an
easily accessible AC outlet. Should you
notice an abnormality in the unit, disconnect
the main plug from the AC outlet
immediately.
Do not install the appliance in a confined
space, such as a bookcase or built-in cabinet.
Do not expose batteries or appliances with
battery-installed to excessive heat, such as
sunshine and fire.
The unit is not disconnected from the mains
as long as it is connected to the AC outlet,
even if the unit itself has been turned off.
This equipment has been tested and found to
comply with the limits set out in the EMC
Directive using a connection cable shorter
than 3 meters.
CAUTION
The use of optical instruments with this
product will increase eye hazard.
masterpage:Left
When unpacking or handling a big and/or
heavy speaker, be sure to handle the unit
with two or more persons. Dropping the unit
may cause personal injury and/or property
damage.
FOR UNITED STATES
CUSTOMERS. NOT
APPLICABLE IN CANADA,
INCLUDING IN THE
PROVINCE OF QUEBEC.
POUR LES
CONSOMMATEURS AUX
ÉTATS-UNITS. NON
APPLICABLE AU CANADA,
Y COMPRIS LA PROVIBCE
DE QUÉBEC.
For the customers in the
USA
Owner’s Record
The model and serial numbers are located on
the rear of the unit. Record these numbers in
the space provided below. Refer to them
whenever you call upon your Sony dealer
regarding this product.
Model No. __________________________
Serial No. __________________________
This symbol is intended to
alert the user to the
presence of uninsulated
“dangerous voltage” within
the product’s enclosure that
may be of sufficient
magnitude to constitute a
risk of electric shock to
persons.
This appliance is classified as a CLASS 1
LASER product. This marking is located on
the rear exterior.
2GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\020REG.fm]
This symbol is intended to
alert the user to the
presence of important
operating and maintenance
(servicing) instructions in
the literature
accompanying the
appliance.
Important Safety
Instructions
1) Read these instructions.
2)
3)
4)
5)
6)
7)
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8) Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers)
that produce heat.
9) Do not defeat the safety purpose of the
polarized or grounding-type plug. A
polarized plug has two blades with one
wider than the other. A grounding type
plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.
11) Only use attachments/accessories
specified by the manufacturer.
masterpage:Right
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
13) Unplug this apparatus during lightning
storms or when unused for long periods
of time.
14) Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
NOTE:
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in
a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
– Reorient or relocate the receiving
antenna.
3GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\020REG.fm]
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced
radio/TV technician for help.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
Properly shielded and grounded cables and
connectors must be used for connection to
host computers and/or peripherals in order to
meet FCC emission limits.
Compact Disc Receiver
(HCD-SHAKE99/HCD-SHAKE77/
HCD-SHAKE55/HCD-SHAKE33)
This equipment must not be co-located or
operated in conjunction with any other
antenna or transmitter.
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio
frequency (RF) Exposure Guidelines. This
equipment has very low levels of RF energy
that it deemed to comply without maximum
permissive exposure evaluation (MPE). But
it is desirable that it should be installed and
operated keeping the radiator at least 20 cm
or more away from person’s body (excluding
extremities: hands, wrists, feet and ankles).
masterpage:Left
For the customers in
Canada
Properly shielded and grounded cables and
connectors must be used for connection to
host computers and/or peripherals.
Compact Disc Receiver
(HCD-SHAKE99/HCD-SHAKE77/
HCD-SHAKE55/HCD-SHAKE33)
This device complies with Industry Canada
licence-exempt RSS standard(s).
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must accept
any interference, including interference that
may cause undesired operation of the device.
This equipment complies with IC radiation
exposure limits set forth for an uncontrolled
environment and meets RSS-102 of the IC
radio frequency (RF) Exposure rules.
This equipment has very low levels of RF
energy that it deemed to comply without
maximum permissive exposure evaluation
(MPE). But it is desirable that it should be
installed and operated keeping the radiator at
least 20 cm or more away from person’s
body (excluding extremities: hands, wrists,
feet and ankles).
4GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\020REG.fm]
For customers in Europe
Disposal of waste
batteries and
electrical and
electronic equipment
(applicable in the
European Union and
other European
countries with
separate collection
systems)
This symbol on the product, the battery or on
the packaging indicates that the product and
the battery shall not be treated as household
waste. On certain batteries this symbol might
be used in combination with a chemical
symbol. The chemical symbols for mercury
(Hg) or lead (Pb) are added if the battery
contains more than 0.0005% mercury or
0.004% lead. By ensuring these products and
batteries are disposed of correctly, you will
help prevent potentially negative
consequences for the environment and
human health which could otherwise be
caused by inappropriate waste handling. The
recycling of the materials will help to
conserve natural resources.
In case of products that for safety,
performance or data integrity reasons require
a permanent connection with an incorporated
battery, this battery should be replaced by
qualified service staff only. To ensure that
the battery and the electrical and electronic
equipment will be treated properly, hand
over these products at end-of-life to the
applicable collection point for the recycling
of electrical and electronic equipment. For
all other batteries, please view the section on
how to remove the battery from the product
safely. Hand the battery over to the
applicable collection point for the recycling
of waste batteries. For more detailed
information about recycling of this product
or battery, please contact your local Civic
Office, your household waste disposal
service or the shop where you purchased the
product or battery.
masterpage:Right
Notice for customers: The
following information is only
applicable to equipment sold in
countries applying EU Directives.
This product has been manufactured by or on
behalf of Sony Corporation, 1-7-1 Konan
Minato-ku Tokyo, 108-0075 Japan. Inquiries
related to product compliance based on
European Union legislation shall be
addressed to the authorized representative,
Sony Deutschland GmbH, Hedelfinger
Strasse 61, 70327 Stuttgart, Germany. For
any service or guarantee matters, please refer
to the addresses provided in the separate
service or guarantee documents.
Hereby, Sony Corp., declares that this
equipment is in compliance with the
essential requirements and other relevant
provisions of Directive 1999/5/EC.
For details, please access the following
URL:
http://www.compliance.sony.de/
For customers in Australia
Disposal of Old
Electrical & Electronic
Equipment
(Applicable in the
European Union and
other European
countries with
separate collection
systems)
5GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\020REG.fm]
License and Trademark Notice
• “WALKMAN” and “WALKMAN” logo
are registered trademarks of Sony
Corporation.
• MPEG Layer-3 audio coding technology
and patents licensed from Fraunhofer IIS
and Thomson.
• Windows Media is either a registered
trademark or trademark of Microsoft
Corporation in the United States and/or
other countries.
• This product is protected by certain
intellectual property rights of Microsoft
Corporation. Use or distribution of such
technology outside of this product is
prohibited without a license from
Microsoft or an authorized Microsoft
subsidiary.
• The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by
Sony Corporation is under license. Other
trademarks and trade names are those of
their respective owners.
• The N Mark is a trademark or registered
trademark of NFC Forum, Inc. in the
United States and in other countries.
masterpage:Left
• “Made for iPod” and “Made for iPhone”
mean that an electronic accessory has been
designed to connect specifically to iPod or
iPhone, respectively, and has been
certified by the developer to meet Apple
performance standards. Apple is not
responsible for the operation of this device
or its compliance with safety and
regulatory standards. Please note that the
use of this accessory with iPod or iPhone
may affect wireless performance.
• All other trademarks and registered
trademarks are of their respective holders.
In this manual, ™ and ® marks are not
specified.
About this manual
The instructions in this manual are for
models SHAKE-99, SHAKE-77,
SHAKE-55 and SHAKE-33.
In this manual, the SHAKE-77 is used for
illustration purpose unless stated otherwise.
The SHAKE-99 consists of:
• Unit
• Speaker system
HCD-SHAKE99 (1)
SS-SHAKE99 (2)
The SHAKE-77 consists of:
• Android™ is a trademark of Google Inc.
• Unit
• Speaker system
• Google Play™ is a trademark of Google
Inc.
The SHAKE-55 consists of:
• iPhone and iPod touch are trademarks of
Apple Inc., registered in the U.S. and other
countries. App Store is a service mark of
Apple Inc.
• Unit
• Speaker system
HCD-SHAKE77 (1)
SS-SHAKE77 (2)
HCD-SHAKE55 (1)
SS-SHAKE55 (2)
The SHAKE-33 consists of:
• Unit
• Speaker system
HCD-SHAKE33 (1)
SS-SHAKE33 (2)
6GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\030TOC.fm]
masterpage:Right
Table of Contents
About this manual ........................6
Guide to parts and controls ..........9
Getting Started
Hooking up the system
securely ......................................13
Positioning the speakers.............15
Setting the clock.........................16
Changing the display mode........16
Disc/USB Playback
Playing a disc .............................16
Before using a USB device with
this system..................................17
Playing a USB device ................17
Searching for a track or audio
file (Track Search) .....................18
Using play mode ........................18
USB Transfer
Transferring music .....................20
Tuner
Bluetooth
About the Bluetooth wireless
technology ................................. 24
Setting the Bluetooth audio
codecs........................................ 24
Connecting a smartphone with
one touch (NFC)........................ 25
Listening to music wirelessly
on a Bluetooth device ................ 26
Setting the Bluetooth standby
mode.......................................... 28
Setting the Bluetooth signal ...... 28
Using “SongPal” via
Bluetooth ................................... 28
Sound Adjustment
Adjusting the sound .................. 29
Selecting the Virtual Football
mode.......................................... 29
Creating your own sound
effect.......................................... 30
Creating a party atmosphere
(DJ EFFECT) ............................ 30
Listening to the radio .................23
7GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\030TOC.fm]
masterpage:Left
Other Operations
Using the Party Chain
function...................................... 31
Singing along............................. 32
Changing the spectrum pattern
of the display panel.................... 33
Viewing information in the
display panel.............................. 33
Changing the illumination
pattern and color ........................ 33
Using the timers......................... 33
Using optional equipment ......... 34
Deactivating the buttons on the
unit (Child Lock) ....................... 35
Setting the automatic standby
function...................................... 35
Additional Information
Playable discs ............................ 36
Websites for compatible
devices ....................................... 36
Troubleshooting......................... 37
Messages.................................... 41
Precautions ................................ 42
Specifications ............................ 44
8GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\04PLA.fm]
masterpage:Right
Guide to parts and controls
This manual mainly explains operations using the remote control, but the same operations
can also be performed using the buttons on the unit having the same or similar names.
Unit
SHAKE-99
E
C D
C
F
G
H
I
B
J
K
A
L
R
Q
C P O N M
SHAKE-77/SHAKE-55/SHAKE-33
B
C
D
C
F
H E
A
I
G
J
R
L
S
K Q C P O NM
9GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\04PLA.fm]
masterpage:Left
* When pressing the buttons, press on the printings of the buttons as shown below.
SHAKE-99
SHAKE-77/SHAKE-55/SHAKE-33
** SHAKE-77/SHAKE-55 only.
Remote control RM-AMU199
I
T
A
Q
D
FOOTBALL
Select the Virtual Football mode
(page 29).
Unit: PARTY CHAIN (page 31)
Hold down to activate or deactivate
the Party Chain function.
B
J
Z
C
Y
Unit: BASS BAZUCA (page 29)
Press to select the BASS BAZUCA
effect.
Hold down to select the BASS CUT
effect.
U
V
D
W
C
X
1 "/1 (on/standby)
Turn on the system, or set it to
standby mode.
B MUSIC, MOVIE/GAME
Select the preset sound effect
(page 29).
C
/ / /
Select the menu items.
Remote control: PRESET+/–
Select a preset station during TUNER
function.
+/– (select folder)
Select a folder on an MP3 disc or a
USB device.
Unit only: Select a preset station
during TUNER function.
m/M (rewind/fast forward)
Hold down to find a point in a track or
file during playback.
./> (go back/go forward)
Select a track or file.
10GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\04PLA.fm]
LED PATTERN (page 33)
Change the illumination pattern on
the speakers and the unit.
TUNING+/–
Tune to the station you want during
TUNER function.
x (stop)
Stop playback.
Press twice to cancel resume
playback of the USB device.
J CD
Select the CD function.
Unit: USB/USB SELECT
Remote control: USB
Select the USB function.
Select the USB device connected to
the A or B port during USB
function.
Unit: ENTER
Remote control:
Enter the settings.
Unit: NX (play/pause)
Remote control: N (play)*,
X (pause)
Start or pause playback.
To resume playback, press NX or
N.
D Unit: VOLUME/DJ CONTROL
Adjust the volume.
Adjust the DJ EFFECT level
(page 30).
You cannot use this knob to adjust the
volume when the DJ EFFECT is
activated.
Remote control: DJ CONTROL
+/–
Adjust the DJ EFFECT level.
Remote control: VOLUME +/–*
Adjust the volume.
E
Unit: TUNER/BAND
Select the TUNER function.
Select the FM or AM band during
TUNER function.
Unit: AUDIO IN
Select the AUDIO IN 1 or AUDIO
IN 2 function.
Remote control: FUNCTION
Select a function.
K Remote control sensor
L Display panel
M REC TO USB B
Transfer music to the optional USB
device which is connected to the B
port.
N
(N-Mark) (page 25)
Near Field Communication (NFC)
touchpoint indication.
F Disc tray
I LED COLOR (page 33)
Change the illumination color on the
speakers and the unit.
(USB) B (REC/PLAY) port
Connect and transfer to an optional
USB device.
O MIC jack
Connect a microphone.
MIC LEVEL (MIN/MAX)
Adjust the microphone volume.
G OPTIONS
Enter or exit options menu.
H Z OPEN/CLOSE
Insert or eject a disc.
masterpage:Right
P
(USB) A (PLAY) port
Connect an optional USB device.
Q FLANGER, ISOLATOR, PAN,
WAH (page 30)
Select the DJ EFFECT type.
11GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\04PLA.fm]
masterpage:Left
R BLUETOOTH (page 26, 27)
Press to select Bluetooth function.
Hold down to activate Bluetooth
pairing during Bluetooth function.
S Bottom panel (page 15)
T SLEEP (page 33)
Set the Sleep Timer.
U REPEAT/FM MODE
Listen to a disc, a USB device, a
single track or file repeatedly
(page 19).
Select the FM reception mode
(monaural or stereo) (page 23).
V DISPLAY
Change the information on the
display panel.
W SEARCH/MEMORY
Enter or exit search mode.
Preset the radio station (page 23).
X CLEAR
Delete the last step from the program
list.
Y TIMER MENU (page 16, 34)
Set the clock and the timers.
Z PLAY MODE
Select the play mode of an AUDIO
CD, MP3 disc or a USB device
(page 18).
* The VOLUME + and N buttons have a
tactile dot. Use the tactile dot as a reference
when operating the system.
12GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\05CON.fm]
masterpage:Right
Getting Started
Hooking up the system securely
SHAKE-99
Getting Started
See below.
SHAKE-77/SHAKE-55/SHAKE-33
C is different
depending on the model.
See below.
SHAKE-99
SHAKE-77
SHAKE-55
SHAKE-33
13GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\05CON.fm]
masterpage:Left
A Antennas
C Speakers
Find a location and an orientation that
provide good reception when you set up
the antennas.
Keep the antennas away from the speaker
cords, the power cord and the USB cable
to avoid picking up noise.
– LEFT SPEAKERS and RIGHT
SPEAKERS terminals (SHAKE-99/
SHAKE-77/SHAKE-55 only)
– MID/TWEETERS and WOOFERS
terminals (SHAKE-33 only)
Connect the speaker connectors to
match the color of the speaker terminals
of the unit.
Extend the FM lead
antenna horizontally
Example:
Black
AM loop
antenna
B Audio
Use an audio cord (not supplied) to make
either connection as follows:
– AUDIO OUT/PARTY CHAIN OUT L/R
jacks
– Connect to the audio input jacks of an
optional equipment.
– Connect to another audio system to
enjoy the Party Chain function
(page 31).
– AUDIO IN 1/PARTY CHAIN IN L/R
jacks
– Connect to the audio output jacks of a
TV or an audio/video equipment. The
sound is output through this system.
– Connect to another audio system to
enjoy the Party Chain function
(page 31).
– AUDIO IN 2 L/R jacks
Connect to the audio output jacks of a
computer or gaming device. The sound
is output through this system.
Notes
• Be sure to use only the supplied speakers.
• When connecting speaker cords, insert the
connector straight into the terminals.
– LED SPEAKER terminals
Connect the LED SPEAKER connector
of the speaker to this terminal.
The lighting on the speakers will react
according to the music source. You can
select the illumination pattern and color
according to your preference (page 33).
Example:
D Power
Plug the power cord into a wall socket.
The demonstration appears in the display
panel. Press "/1 to turn on the system and
the demonstration automatically ends.
If the supplied adaptor on the plug does
not fit your wall outlet, detach it from the
plug (only for models equipped with an
adaptor).
14GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\05CON.fm]
masterpage:Right
2 Insert the pins of the bottom
Inserting batteries
Insert the two supplied R6 (size AA)
batteries, matching the polarities as
shown below.
panel to the catcher holes. Then,
push the bottom panel until it
locks into the main unit.
Catcher hole
Pin
Getting Started
Notes
• Do not mix an old battery with a new one or
mix different types of batteries.
• If you do not use the remote control for a long
period of time, remove the batteries to avoid
damage from battery leakage and corrosion.
Attaching the bottom panel
(SHAKE-77/SHAKE-55/SHAKE-33
only)
You can attach the supplied bottom panel
to the bottom of the main unit to raise the
front panel and to ease the operations.
1 Insert the hooks of the bottom
panel to the catcher holes on the
bottom of the main unit.
Bottom
panel
Hook
Catcher
hole
Positioning the
speakers
To obtain optimum performance from the
system, we recommend you to place the
speakers as shown below.
A Unit
B Speaker (left)
C Speaker (right)
B
A
0.3 m (1 foot)
C
0.3 m (1 foot)
45
Main unit
15GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\06BAS.fm]
Setting the clock
masterpage:Left
Disc/USB Playback
You cannot set the clock in Power Saving
Mode.
Playing a disc
1 Press "/1 to turn on the system.
2 Press TIMER MENU.
1 Press CD.
2 Press Z OPEN/CLOSE on the
If “PLAY SET” appears in the display
panel, press / repeatedly to select
“CLOCK SET”, then press
.
3 Press
/ repeatedly to set the
hour, then press
.
4 Press
/ repeatedly to set the
minutes, then press
.
Changing the display
mode
The demonstration appears in the display
panel once you plug the power cord into a
wall socket.
Press DISPLAY repeatedly while
the system is turned off.
unit.
3 Load a disc with the label side
facing up on the disc tray.
When you play
back an 8 cm
disc such as a
CD single, place
it on the inner
circle of the tray
4 Press Z OPEN/CLOSE on the
unit to close the disc tray.
Do not forcibly push the disc tray to
close it as this may cause a
malfunction.
5 Press N to start playback.
Demonstration
The display changes and the indicator
flashes even when the system is turned
off.
No display (Power Saving Mode)
The display is turned off to conserve
power. The timer and clock continue to
work internally.
Clock
The clock display automatically turns to
Power Saving Mode after a few seconds.
16GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\06BAS.fm]
Before using a USB
device with this system
Check the information on the website
about compatible USB devices (page 36).
To select the playback source or
transfer destination (USB Memory
Select)
Note
You cannot select a memory during playback or
transfer. Make sure to select a memory before
starting playback or transfer.
Playing a USB device
The audio formats that can be played back
by this system are as follows:
– MP3: file extension “.mp3”
– WMA: file extension “.wma”
– AAC: file extension “.m4a”, “.mp4” or
“.3gp”
If the audio files have the above file
extension but are not the respective
formats, the system may produce noise or
may malfunction.
1 Press USB repeatedly until
“USB A” or “USB B” lights up in
the display panel.
2 Connect a USB device to the
A
or B port according to your
selection in step 1.
Disc/USB Playback
If the USB device has more than one
memory (for example, an internal
memory and a memory card), you can
select which memory to use as a playback
source or transfer destination.
Use the buttons on the unit to perform this
operation.
masterpage:Right
1 Press USB/USB SELECT
repeatedly until “USB A” or “USB B”
lights up in the display panel.
2 Connect a USB device to the
A or
B port according to your selection
in step 1.
3 Press OPTIONS when playback is
USB device
stopped.
4 Press
/ to select “USB MEM
SEL”, then press ENTER.
5 Press
/ to select the memory
you want, then press ENTER.
To exit the options menu, press
OPTIONS on the unit.
Notes
• You can use your iPhone/iPod with this
system via Bluetooth connection only.
• You can use a USB adaptor (not supplied)
to connect the USB device to the unit if the
USB device cannot be plugged into the
port.
3 Press N to start playback.
The audio files are played back in
different orders depending on the play
mode (page 18).
17GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\06BAS.fm]
Searching for a track
or audio file
masterpage:Left
Using play mode
Playing in original order
(Normal Play)
(Track Search)
1 Press SEARCH.
“SEARCH” lights up in the display
panel.
2 (Audio files only)
Press / to select the folder
you want, then press
or N.
To search in other folders, press to
exit, then select the folder you want.
3 Press
/ to select the track or
audio file you want, then press
or N.
The selected track or audio file starts
playback.
Press PLAY MODE repeatedly when
playback is stopped.
When playing a disc
• (blank): play a disc
• FLDR*: play all audio files in the
specified folder on the disc
* When playing an AUDIO CD, “FLDR”
performs the same operation as “(blank)” play
mode.
When playing a USB device
• ALL USB: play all USB devices
• 1 USB: play a USB device
• FLDR: play all audio files in the
specified folder on the USB device
Notes on disc
• (For AUDIO CD) This system can recognize
up to 99 tracks.
• (For MP3 dics) This system can recognize up
to
– 999 folders (including root and empty
folders).
– 999 MP3 files.
– 250 MP3 files in a folder.
– 8 folders levels (tree structure of files).
• CD-TEXT information is not supported.
Notes on USB device
• This system can recognize up to
– 1,000 folders in a USB device (including
root and empty folders).
– 3,000 audio files in a USB device.
– 250 audio files in a folder.
Playing in random order
(Shuffle Play)
Press PLAY MODE repeatedly when
playback is stopped.
When playing a disc
• SHUF: shuffle all audio files on a disc
• FLDR SHUF*: shuffle all audio files in
the specified folder on the disc
* When playing an AUDIO CD, “FLDR
SHUF” performs the same operation as
“SHUF” play mode.
When playing a USB device
• ALL USB SHUF: shuffle all audio files
on all USB devices
• 1 USB SHUF: shuffle all audio files on
a USB device
• FLDR SHUF: shuffle all audio files in
the specified folder on the USB device
Note
When you turn off the system, the selected
Shuffle Play is cleared and the play mode
returns to Normal Play.
18GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\06BAS.fm]
Creating your own program
(Program Play)
You can make a program of up to 25 steps
in the order you want them to be played
back.
1 For CD function:
Press CD to select CD function.
For USB function:
2 When playback is stopped,
press PLAY MODE repeatedly
until “PGM” lights up in the
display panel.
3 (Audio files only)
Press
+/– repeatedly to select
a folder.
If you want to program all files in the
folder, press
.
4 Press ./> repeatedly to
select the track or audio file you
want, then press
.
Selected track
or file number
Total playing time of
program (including
selected track or file)
To delete the last step from the
program list
Press CLEAR when playback is stopped.
To cancel Program Play
When playback is stopped, press PLAY
MODE repeatedly until “PGM”
disappears from the display panel.
Notes
• (CD function only) The program list is cleared
when you open the disc tray.
• (USB function only) The program list is
cleared when you:
– perform the erase operation.
– remove the USB device.
– change the selected USB memory.
Playing repeatedly (Repeat
Play)
Press REPEAT repeatedly.
•
: repeat all tracks or audio files on a
folder/disc/USB device/program
•
: repeat a track or audio file
Disc/USB Playback
Press USB repeatedly to select the
USB device you want.
masterpage:Right
Notes on the USB device
• The playback order for the system may differ
from the playback order of the connected
digital music player.
• You cannot erase audio files and folders in
Shuffle Play or Program Play.
“--.--” appears when the total playing
time exceeds 100 minutes for an
AUDIO CD or when you program an
audio file.
5 Repeat steps 3 to 4 to program
additional tracks or audio files.
6 Press N to start Program Play.
19GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\06BAS.fm]
masterpage:Left
2 Press
/ repeatedly to select
“REC BIT RATE”, then press
ENTER.
USB Transfer
Transferring music
You can transfer music from a sound
source to a USB device connected to the
B port.
The audio format of files transferred by
this system is MP3. However, you can
also transfer WMA and AAC files from
USB A.
Notes
• Do not remove the USB device during
transfer or erase operations. Doing so may
corrupt the data on the USB device or damage
the USB device itself.
• MP3/WMA/AAC files are transferred with
the same bit rate as the original files.
• When transferring from an AUDIO CD,
TUNER, AUDIO IN 1 or AUDIO IN 2
function, you may select the bit rate before
transferring.
• USB transfer and erase operations are
disabled while the disc tray is open.
Note on copyright-protected
content
The transferred music is limited to private
use only. Use of the music beyond this
limit requires permission of the copyright
holders.
3 Press / repeatedly to select the
bit rate you want, then press
ENTER.
• 128 KBPS: encoded MP3 tracks have
smaller file size and lower audio
quality.
• 256 KBPS: encoded MP3 tracks have
bigger file size but higher audio
quality.
To exit the options menu, press
OPTIONS on the unit.
Transferring music from a disc
or USB device
You can easily transfer all the music on a
disc or USB A to USB B (Synchronized
Transfer). You can also transfer a single
track or audio file during playback
(REC1 Transfer).
Use the buttons on the unit to perform this
operation.
1 Connect a transferable USB
device to the
below.
B port as shown
To select the playback source or
transfer destination (USB Memory
Select)
See page 17.
To select the bit rate
You can select a higher bit rate to transfer
music with better quality.
Use the buttons on the unit to perform this
operation.
1 Press OPTIONS.
USB device
Note
You can use a USB adaptor (not supplied) to
connect the USB device to the unit if the
USB device cannot be plugged into the
port.
20GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\06BAS.fm]
2 For disc:
Press CD, then load the disc.
For USB:
Press USB/USB SELECT repeatedly
until “USB A” lights up in the display
panel, then connect the USB device
containing audio files you want to
transfer to A port.
3 For Synchronized Transfer:
When playback is stopped, press
PLAY MODE on the remote control
repeatedly to select the play mode you
want.
• If you start transferring in Shuffle Play
(“FLDR SHUF”), the selected play mode
changes to “FLDR” automatically.
• If you start transferring in Shuffle Play
(except “FLDR SHUF”), Repeat Play or
Program Play with no steps, the selected
play mode changes to Normal Play
automatically.
For REC1 Transfer:
Select the track or audio file you want
to transfer, then start playback.
4 Press REC TO USB B.
“PUSH ENTER” appears in the
display panel.
5 Press ENTER.
The transfer starts when “DON’T
REMOVE” appears in the display
panel.
For Synchronized Transfer:
When the transfer is completed, the
transfer source and the USB device
stop automatically.
For REC1 Transfer:
Transferring analog audio
(Analog Transfer)
You can transfer sound from an analog
audio source (other than CD, USB or
Bluetooth function) to a USB device.
Use the buttons on the unit to perform this
operation.
1 Connect a transferable USB
device to the
B port (page 20).
2 Press TUNER/BAND or AUDIO IN
repeatedly to select the source
you want to transfer.
3 Press REC TO USB B.
“PUSH ENTER” appears in the
display panel.
4 Press ENTER.
USB Transfer
Notes
masterpage:Right
The transfer starts when “DON’T
REMOVE” appears in the display
panel.
5 Start playing the source.
To stop transfer
Press x.
To create a new MP3 file
Press REC TO USB B during Analog
Transfer.
“NEW TRACK” appears in the display
panel.
A new MP3 is also created automatically
after approximately 1 hour of transfer.
Notes
• When a new MP3 file is created, transfer is
disabled for the time being.
• If you press REC TO USB B again after a few
seconds, a new MP3 file can be created.
When the transfer is completed, the
disc or the USB device continues to
play.
21GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\06BAS.fm]
Erasing audio files or folders
from a USB device
Use the buttons on the unit to perform this
operation.
1 Press USB/USB SELECT
repeatedly until “USB A” or
“USB B” lights up in the display
panel when playback is stopped.
2 Press ./> or
+/–
repeatedly to select the audio
file or folder.
3 Press OPTIONS.
4 Press / to select “USB
ERASE”, then press ENTER.
“FOLDER ERASE” or “TRACK
ERASE” appears in the display panel.
5 Press ENTER.
“COMPLETE” appears in the display
panel.
To exit the options menu, press
OPTIONS on the unit.
Folder and file generation
rules
When transferring to a USB device, a
“MUSIC” folder is created directly below
“ROOT”. Folders and files are generated
within this “MUSIC” folder according to
the transfer method and source as follows:
Synchronized Transfer
Source
Folder name
Audio files
Same as the source
File name
AUDIO CD
“CDDA0001”* “TRACK001”*
masterpage:Left
REC1 Transfer
Source
Folder name
File name
Audio files
“REC1-MP3”
Same as the
source
AUDIO CD
“REC1-CD”
“TRACK001”*
Analog Transfer
Source
Folder name
File name
FM
“TUFM0001”*
“TRACK001”*
AM
“TUAM0001”*
AUDIO IN 1/ “EXAU0001”*
AUDIO IN 2
* Folder and file numbers are assigned serially
thereafter.
Notes on transfer
• While transferring (except analog transfer),
no sound is output.
• CD-TEXT information is not transferred to
the created MP3 files.
• The transfer stops automatically if:
– the USB device runs out of space during
transfer.
– the number of audio files or folders on the
USB device reaches the limit that the
system can recognize (page 18).
• If a folder or file that you are trying to transfer
already exists on the USB device with the
same name, a sequential number is added after
the name without overwriting the original
folder or file.
• You cannot perform the following operations
during transfer:
– Eject the disc.
– Select another track or file.
– Pause playback or find a point in the track or
file.
– Change the function or tuner band.
• When transferring music to a Walkman®
using “Media Manager for WALKMAN”, be
sure to transfer in MP3 format.
• When connecting a Walkman® to the system,
be sure to connect after the display “Creating
Library” or “Creating Database” on the
Walkman® has disappeared.
22GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\06BAS.fm]
masterpage:Right
To change the AM tuning interval
(Except for European model)
Tuner
select FM or AM band.
The default setting for AM tuning interval
is 9 kHz (or 10 kHz for some areas). You
cannot change the AM tuning interval in
Power Saving Mode.
Use the buttons on the unit to perform this
operation.
2 For automatic scanning:
1 Press TUNER/BAND repeatedly to
Listening to the radio
1 Press FUNCTION repeatedly to
select AM band.
2 Press "/1 to turn off the system.
3 While holding down TUNER/BAND,
press "/1.
“AM 9K STEP” or “AM 10K STEP”
appears in the display panel.
When you change the interval, all the
AM preset stations are erased.
Presetting radio stations
Tuner
Hold down TUNING+/– until the
frequency indication changes and then
release.
Scanning stops automatically when a
station is tuned in. “TUNED” and
“ST” (for FM stereo programs only)
light up in the display panel.
If “TUNED” does not light up and
scanning does not stop, press x to stop
scanning. Then, perform manual
tuning (below).
For manual tuning:
Press TUNING+/– repeatedly to tune
to the station you want.
Note
When you tune to an FM station that provides
RDS services, information such as the service
name or station name is provided by broadcasts.
You can check the RDS information by pressing
DISPLAY repeatedly.
You can store up to 20 FM and 10 AM
stations as your favorite stations.
1 Tune to the station you want.
2 Press MEMORY.
Preset number
Tip
To reduce static noise on a weak FM stereo
station, press FM MODE repeatedly until
“MONO” lights up in the display panel.
3 Press TUNING+/– repeatedly to
select the preset number you
want, then press
.
“COMPLETE” appears in the display
panel. The station is stored.
To tune to a preset station
Press PRESET+/– (or
+/– on the unit)
repeatedly to select the preset number you
want.
23GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\06BAS.fm]
Bluetooth
About the Bluetooth
wireless technology
Bluetooth wireless technology is a shortrange wireless technology that enables
wireless data communication between
digital devices. Bluetooth wireless
technology operates within a range of
about 10 meters (33 feet).
Supported Bluetooth version,
profiles and codecs
Supported Bluetooth version:
• Bluetooth Standard version 3.1
Supported Bluetooth profiles:
• A2DP (Advanced Audio Distribution
Profile)
• AVRCP 1.3 (Audio Video Remote
Control Profile)
• SPP (Serial Port Profile)
Supported Bluetooth codecs:
• SBC (Sub Band Codec)
• AAC (Advanced Audio Coding)
About the BLUETOOTH
indicator
The BLUETOOTH indicator lights up or
flashes in blue to show the Bluetooth
status.
System status
masterpage:Left
Setting the Bluetooth
audio codecs
You can receive data in AAC codec
format from a Bluetooth device.
1 Press BLUETOOTH on the unit
to select Bluetooth function.
“BLUETOOTH” appears in the
display panel.
2 Press OPTIONS on the unit.
3 Press / repeatedly to select
“BT AAC”, then press
.
4 Press
/ repeatedly to select
“BT AAC ON” or “BT AAC OFF”.
• BT AAC ON: Enable reception in
AAC codec format.
• BT AAC OFF: Receive in SBC
codec format.
To exit the options menu, press
OPTIONS on the unit.
Notes
• You can enjoy high quality sound if the AAC
is selected. In case you cannot listen to AAC
sound from your device, select “BT AAC
OFF”.
• If you change this setting while the system is
connected to a Bluetooth device, the
Bluetooth device will be disconnected. To
connect to the Bluetooth device, perform the
Bluetooth connection again.
Indicator status
Bluetooth standby
Flashes slowly
Bluetooth pairing
Flashes quickly
Bluetooth connection Lights up
is established
24GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\06BAS.fm]
Connecting a
smartphone with one
touch (NFC)
masterpage:Right
• Depending on your smartphone, you can
use the NFC function without installing
the app. In this case, the operations and
specifications may differ. For details,
refer to the operating instructions of your
smartphone.
Compatible smartphones
What is “NFC”?
NFC (Near Field Communication) is a
technology enabling short-range wireless
communication between various devices,
such as smartphones and IC tags. Thanks
to the NFC function, data communication
can be achieved easily just by touching
the designated touchpoint on the NFCcompatible devices.
2 Start the “NFC Easy Connect”
app on the smartphone.
Make sure that the app screen is
displayed.
3 Touch the smartphone to the
N-Mark on the system until the
smartphone vibrates.
SHAKE-99:
1 Download and install the “NFC
Bluetooth
When you touch the system with an NFCcompatible smartphone, the system
automatically:
– turns on in Bluetooth function.
– completes pairing.
– completes the Bluetooth connection.
Smartphones with a built-in NFC
function (OS: Android 2.3.3 or later,
excluding Android 3.x)
Easy Connect” app.
Download the free Android app from
Google Play by searching for “NFC
Easy Connect” or access it by using the
two-dimensional code below. Data
communication fees may be charged.
Two-dimensional code* for
direct access
SHAKE-77/SHAKE-55/SHAKE-33:
* Use a two-dimensional code reader app.
Notes
• The app may not be available in some
countries/regions.
Complete the connection by following
the instructions displayed on the
smartphone.
25GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\06BAS.fm]
When the Bluetooth connection is
established, the BLUETOOTH
indicator stops flashing and remains
light up. Bluetooth device name
appears in the display panel.
You can switch the sound source from
the smartphone to another NFCcompatible Bluetooth device.
For details, refer to the operating
instructions of your Bluetooth device.
Tip
If pairing and the Bluetooth connection fail, do
the following.
– Relaunch “NFC Easy Connect” and move the
smartphone slowly over the N-Mark.
– Remove the case from the smartphone if using
a commercially available smartphone case.
To play music from the smartphone
Start playing of an audio source on the
smartphone. For details on playback, refer
to the operating instructions of your
smartphone.
To disconnect the smartphone
Touch the smartphone to the N-Mark on
the system again.
masterpage:Left
Pairing this system with a
Bluetooth device
Pairing is an operation where Bluetooth
devices register with each other
beforehand. Once a pairing operation is
performed, it does not need to be
performed again. If your device is an
NFC-compatible smartphone, the manual
pairing procedure is not necessary.
1 Place the Bluetooth device
within 1 meter (3 feet) from the
system.
2 Press BLUETOOTH on the unit
to select Bluetooth function.
“BLUETOOTH” appears in the
display panel.
Note
If the system is connected to a Bluetooth
device, press BLUETOOTH to disconnect
the Bluetooth device.
3 Hold down BLUETOOTH on the
unit for 2 seconds or more.
“PAIRING” flashes in the display
panel.
Listening to music
wirelessly on a
Bluetooth device
You can listen to music from your
Bluetooth device over a wireless
connection.
Check the information on the website
about compatible Bluetooth devices
(page 36).
4 Perform the pairing procedure
on the Bluetooth device.
For details, refer to the operating
instructions of your Bluetooth device.
5 Select the model number of the
unit on the display of the
Bluetooth device.
For example, select
“SONY:SHAKE-99” (or SHAKE-77/
SHAKE-55/SHAKE-33).
If passkey is required on the Bluetooth
device, enter “0000”.
26GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\06BAS.fm]
6 Perform the Bluetooth
connection on the Bluetooth
device.
When pairing is completed and the
Bluetooth connection is established,
Bluetooth device name appears in the
display panel.
Depending on the Bluetooth device,
connection may start automatically
after pairing is completed.
You can check the Bluetooth device
address by pressing DISPLAY
repeatedly.
Notes
To cancel the pairing operation
Hold down BLUETOOTH on the unit for
2 seconds or more until “BLUETOOTH”
appears in the display panel.
Playing music from a
Bluetooth device
1 Press BLUETOOTH on the unit
to select Bluetooth function.
“BLUETOOTH” appears in the
display panel.
2 Establish connection with the
Bluetooth device.
The last connected Bluetooth device
will be connected automatically.
Perform the Bluetooth connection
from the Bluetooth device if the device
is not connected.
Once the connection is established, the
Bluetooth device name appears in the
display panel.
3 Press N to start playback.
Depending on the Bluetooth device,
– you may need to press N twice.
– you may need to start playing an
audio source on the Bluetooth
device.
Notes
• When the system is not connected to any
Bluetooth device, the system will connect and
play back from the last connected Bluetooth
device automatically when you press N.
• If you try to connect another Bluetooth device
to the system, the current connected Bluetooth
device will be disconnected.
Bluetooth
• You can pair up to 9 Bluetooth devices. If the
10th Bluetooth device is paired, the oldest
paired device will be deleted.
• “Passkey” may be called “Passcode”, “PIN
code”, “PIN number” or “Password”, etc.,
depending on the device.
• The pairing standby status of the system is
canceled after about 5 minutes. If pairing is
not successful, repeat from step 1.
• While connected to a Bluetooth device, this
system cannot be detected and connection
cannot be established from another Bluetooth
device which is never paired before.
• If you want to pair with another Bluetooth
device, repeat steps 1 to 6.
masterpage:Right
To disconnect the Bluetooth device
Press BLUETOOTH on the unit.
“BLUETOOTH” appears in the display
panel.
Depending on the Bluetooth device, the
Bluetooth connection may be canceled
automatically when you stop playback.
You can operate a Bluetooth device by
connecting the system and the Bluetooth
device using AVRCP.
Check the following before playing
music:
– The Bluetooth function of the Bluetooth
device is turned on.
– Pairing has been completed.
27GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\06BAS.fm]
Erasing all the pairing
registration information
Setting the Bluetooth
signal
Use the buttons on the unit to perform this
operation.
1 Press BLUETOOTH to select
Bluetooth function.
“BLUETOOTH” appears in the
display panel.
If the system is connected to a
Bluetooth device, the Bluetooth device
name appears in the display panel.
Press BLUETOOTH to disconnect the
Bluetooth device.
2 Hold down x and
– for about
3 seconds.
“PAIR HISTORY” and “CLEAR”
appear in the display panel and all the
pairing information is erased.
Setting the Bluetooth
standby mode
The Bluetooth standby mode enables the
system to turn on automatically when you
establish the Bluetooth connection from a
Bluetooth device.
1 Press OPTIONS on the unit.
2 Press / repeatedly to select
“BT STANDBY”, then press
masterpage:Left
.
3 Press
/ repeatedly to select
“STANDBY ON” or “STANDBY
OFF”.
4 Press ?/1 to turn off the system.
When the Bluetooth standby mode is
set to on, the system waits for a
Bluetooth connection even when the
system has been turned off. When a
Bluetooth connection is established,
the system turns on automatically.
You can connect to the system from a
paired Bluetooth device in all functions
when Bluetooth signal is set to on. The
Bluetooth signal is turned on by default.
Use the buttons on the unit to perform this
operation.
Hold down MOVIE/GAME and LED
COLOR for about 3 seconds.
“BT ON” or “BT OFF” appears in the
display panel.
Notes
• You cannot perform the following operations
when Bluetooth signal is set to off:
– Pairing with Bluetooth device
– Erasing the pairing information
– Using “SongPal” via Bluetooth
• When the Bluetooth signal is set to off, this
system cannot be detected and connection
cannot be established from Bluetooth device.
• If you touch the system with an NFCcompatible smartphone or set the Bluetooth
standby mode to on, the Bluetooth signals will
set to on automatically.
Using “SongPal” via
Bluetooth
About App
A dedicated app for this model is
available on both Google Play and App
Store. Search for “SongPal” and
download the free app to find out more
about the convenient features.
Bluetooth technology works with
iPhone 5s, iPhone 5c, iPhone 5,
iPhone 4s, iPhone 4, iPhone 3GS, iPod
touch (5th generation), iPod touch (4th
generation).
28GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\06BAS.fm]
Sound Adjustment
Adjusting the sound
To
Do this
Reinforce the
Press BASS BAZUCA on
bass and create the unit.
a more powerful
sound
Reduce the bass Hold down BASS
sound (BASS
BAZUCA on the unit for
CUT)
2 seconds or more.
To cancel the BASS CUT
effect, press BASS
BAZUCA again.
Notes
Select a preset
sound effect
Press MUSIC or MOVIE/
GAME.
To cancel preset sound
effect, press MUSIC
repeatedly to select
“FLAT”.
Selecting the Virtual
Football mode
You can experience a feeling of presence
in the stadium when watching the football
match broadcast.
Press FOOTBALL repeatedly while
watching a football match
broadcast.
• NARRATION ON: You can enjoy an
immersive feeling of being in a football
stadium through enhanced stadium
cheers.
• NARRATION OFF: You can enjoy a
more immersive feeling of being in a
football stadium by minimizing the
volume level of narration in addition to
the enhancement of cheers.
To cancel the Virtual Football mode
Press MUSIC repeatedly to select
“FLAT”.
Notes
• We recommend you to select the football
mode when watching a football match
broadcast.
• If you hear unnatural sound in the content
when “NARRATION OFF” is selected,
“NARRATION ON” is recommended.
• This feature does not support monaural sound.
• You can only select the Virtual Football mode
during AUDIO IN 1 or AUDIO IN 2 function.
Sound Adjustment
• When BASS CUT effect
is turned on, BASS
BAZUCA indicator
flashes and “BASS CUT”
appears in the display
panel every 10 seconds.
• The BASS CUT effect is
turned off automatically
when you turn off the
system.
masterpage:Right
29GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\06BAS.fm]
Creating your own
sound effect
Creating a party
atmosphere
You can raise or lower the levels of
specific frequency bands, then store the
setting in the memory as “CUSTOM EQ”.
1 Press OPTIONS on the unit.
2 Press / repeatedly to select
“EQ EDIT”, then press
.
3 Press
/ repeatedly to adjust
the equalizer level, then press
.
Frequency band
masterpage:Left
Equalizer level
4 Repeat step 3 to adjust the level
of other frequency bands and
surround effect.
To exit the options menu, press
OPTIONS on the unit.
(DJ EFFECT)
1 Press the following button to
select the effect type.
The selected button lights up and the
effect is activated.
• FLANGER: Create a deep flanging
effect that is similar to the roar of a
jet plane.
• ISOLATOR: Isolate a specific
frequency band by adjusting the
other frequency bands. For example,
when you want to focus on vocals.
• PAN: Create a feeling that the sound
is moving around the speakers
between left and right channels.
• WAH: Create a special effect of
“Wah-wah” sound by moving the
frequency of a filter up and down
automatically.
2 Press DJ CONTROL +/– to adjust
the effect level.
To turn off the effect
To select the custom equalizer
setting
Press the selected effect button again.
Press MUSIC repeatedly to select
“CUSTOM EQ”.
• The DJ EFFECT is automatically turned off
when you turn off the system or change the
function or tuner band.
• If you activate the DJ EFFECT during
transfer, the sound effect will not be
transferred to the USB device.
• You cannot use VOLUME/DJ CONTROL
on the unit to adjust the volume when the DJ
EFFECT is activated. Press VOLUME +/– on
the remote control to adjust the volume.
Notes
30GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\07OTH.fm]
Other Operations
Using the Party Chain
function
You can connect multiple audio systems
in a chain to create a more interesting
party environment and to produce higher
sound output.
Activate a system in the chain to be the
“Party Host” and share the music. Other
systems will become “Party Guest” and
play the same music as the “Party Host”.
Setting up the Party Chain
You can set up a Party Chain by
connecting all the systems using audio
cords (not supplied).
Before connecting cords, be sure to
disconnect the power cord.
masterpage:Right
When you make connection A
• Any system can become a Party Host in
this connection.
• You can select a new Party Host when
Party Chain function is activated. For
details, see “To select a new Party Host”
(page 32).
• In this connection, the last system must
be connected to the first system.
B If one of the system is not
equipped with Party Chain
function
First system
Second
system
Continue the connection until
the last system
Last system
First system
When you make connection B
Second
system
Continue the connection until
the last system
Last system
• You can connect the system which is not
equipped with Party Chain function at
the last system. Be sure to select the
function which corresponds to the
“AUDIO IN” jacks on the last system.
• You must select the first system as Party
Host so that all systems are playing the
same music when Party Chain function
is activated.
• In this connection, the last system is not
connected to the first system.
Other Operations
A If all the systems are equipped
with Party Chain function
31GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\07OTH.fm]
Enjoying the Party Chain
Perform the following procedure to
activate the Party Chain function.
1 Plug in the power cord and turn
on all the systems.
2 Adjust the volume on each
system.
3 Activate the Party Chain
function on the system which
you want it to be the Party Host.
Press FUNCTION repeatedly to select
the function (except AUDIO IN 1) you
want, then start playback.
Hold down MUSIC/PARTY CHAIN
on the unit for 2 seconds.
“PARTY CHAIN” appears in the
display panel. The system starts the
party as Party Host and other systems
will become Party Guest
automatically. All systems play the
same music as the Party Host.
Notes
• Depending on the total unit of systems you
have connected, Party Guest may take some
time to start playing the music.
• Changing the volume level and sound effect
on the Party Host will not affect the output on
the Party Guest.
• The Party Guest continues playing the music
source as Party Host even when you change
the function on Party Guest. However, you
can adjust the volume and change the sound
effect on Party Guest.
• (SHAKE-99/SHAKE-77/SHAKE-55 only)
When you use the microphone on Party Host,
the sound will not be output from Party Guest.
• The system which is not equipped with Party
Chain function cannot become a Party Host.
• When Party Chain function is activated while
one of the system in the connection is
performing USB transfer, the Party Chain
function will not be activated on that system
and the systems connected after it. Party
Chain function will only be activated after
that system completed or stopped the USB
transfer.
masterpage:Left
• For details on the operations of other systems,
refer to the operating instructions of the
systems.
To select a new Party Host
When you make connection A, you can
select another system as the new Party
Host.
Repeat step 3 of “Enjoying the Party
Chain” on the system which you want it to
be a new Party Host.
The current Party Host will become Party
Guest automatically. All systems play the
same music as the new Party Host.
To deactivate the Party Chain
On the Party Host, hold down MUSIC/
PARTY CHAIN on the unit for 2 seconds.
Singing along
(SHAKE-99/SHAKE-77/SHAKE-55
only)
You can sing along with any audio source
that is playing on this system.
1 Turn MIC LEVEL to MIN to reduce
the microphone volume level.
2 Connect a microphone to the
MIC jack on the unit.
3 Start playing the music and
adjusting the volume.
4 Turn MIC LEVEL to adjust the
microphone volume.
If acoustic feedback (howling) occurs,
reduce the volume, move the
microphone away from the speakers,
or change the direction of the
microphone.
After you have finished, disconnect the
microphone.
32GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\07OTH.fm]
Note
The sound from the microphone will not be
transferred to the USB device during USB
transfer.
Changing the spectrum
pattern of the display
panel
1 Press OPTIONS on the unit.
2 Press / repeatedly to select
“SPECTRUM”, then press
.
3 Press
/ repeatedly to select
the spectrum pattern you want,
then press
.
To exit the options menu, press
OPTIONS on the unit.
Press DISPLAY repeatedly when
the system is turned on.
You can view the information as follows:
• For AUDIO CD:
– The elapsed playing time and
remaining playing time during
playback.
– The total playing time when playback
is stopped.
• For audio files:
– The elapsed playing time, file name
and folder name.
– The title, artist and album information.
Changing the
illumination pattern
and color
Press LED PATTERN or LED
COLOR to show the current setting.
Press repeatedly to select the
illumination pattern or color on the
unit and the speakers.
To turn off the illumination, press LED
PATTERN repeatedly to select
“PATTERN OFF”.
Note
If the illumination brightness is glaring, switch
on the room lights or turn off the illumination.
Using the timers
The system offers three timer functions.
You cannot activate both the Play Timer
and the Recording Timer at the same time.
If you use either with the Sleep Timer, the
Sleep Timer has priority.
Sleep Timer
You can fall asleep while listening to
music. The system turns off after the
preset time.
Other Operations
Viewing information in
the display panel
masterpage:Right
Press SLEEP repeatedly.
To cancel Sleep Timer, press SLEEP
repeatedly to select “SLEEP OFF”.
Tip
To check the remaining time before the system
turns off, press SLEEP.
Note
The elapsed playing time of an audio file
encoded using a VBR (variable bit rate) is not
displayed correctly.
33GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\07OTH.fm]
Play Timer/Recording Timer
Make sure you have set the clock.
Play Timer:
You can wake up to disc, tuner or USB
device at a preset time.
Recording Timer:
You can transfer music from a preset radio
station to a USB device at a specified
time.
masterpage:Left
To check the timer setting or
activate the timer again
1 Press TIMER MENU.
“TIMER SELECT” flashes in the
display panel.
2 Press
3 Press
.
/ repeatedly to select
“PLAY SELECT” or “REC
SELECT”, then press
.
To cancel the timer
1 For Play Timer:
Prepare the sound source, then press
VOLUME +/– to adjust the volume.
To start from a specific track or file,
create your own program (page 19).
For Recording Timer:
Tune to the preset radio station
(page 23).
2 Press TIMER MENU.
3 Press / repeatedly to select
Repeat the same procedure as above and
select “TIMER OFF” in step 3, then press
.
Notes
• The system turns on before the preset time. If
the system is turned on at the preset time or if
“STANDBY” flashes in the display panel, the
Play Timer and the Recording Timer will not
play or transfer.
• Do not operate the system from the time the
system turns on until the playback or transfer
starts.
“PLAY SET” or “REC SET”, then
press
.
4 Set the time to start playback or
transfer.
Press / repeatedly to set the hour/
minute, then press
.
5 Use the same procedure as in
step 4 to set the time to stop
playback or transfer.
6 Press
/ repeatedly to select
the sound source you want, then
press
.
For Recording Timer:
Connect a transferable USB device to
the B port.
7 Press "/1 to turn off the system.
Using optional
equipment
1 Press VOLUME – repeatedly
until “VOLUME MIN” appears in
the display panel.
2 Connect an optional equipment
(page 14).
3 Press FUNCTION repeatedly to
select the function which
corresponds to the connected
equipment.
4 Start playing the connected
equipment.
5 Press VOLUME + repeatedly to
Note
If the system remains on, the timers will not
take effect.
adjust the volume.
34GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\07OTH.fm]
Note
The system may enter standby mode
automatically if the volume level of the
connected equipment is too low. Adjust the
volume level of the equipment. To turn off
automatic standby function, see “Setting the
automatic standby function” (page 35).
Deactivating the
buttons on the unit
(Child Lock)
You can deactivate the buttons on the unit
(except "/1) to prevent misoperation,
such as child mischief.
Hold down x on the unit for more
than 5 seconds.
Note
Child Lock function will be canceled when you
disconnect the power cord.
Setting the automatic
standby function
This system is equipped with an
automatic standby function. With this
function, the system enters standby mode
automatically in about 15 minutes when
there is no operation or audio signal
output.
By default, the automatic standby
function is turned on.
1 Press OPTIONS on the unit.
2 Press / repeatedly to select
“AUTO STANDBY”, then press
.
3 Press
/ repeatedly to select
“ON” or “OFF”.
To exit the options menu, press
OPTIONS on the unit.
Notes
• The message “AUTO STANDBY” flashes in
the display about 2 minutes before entering
standby mode.
• The automatic standby function does not work
during tuner function.
• The system may not enter standby mode
automatically in the following cases:
– when an audio signal is detected.
– during playback of audio files.
– while the preset Play Timer, Recording
Timer or Sleep Timer is in process.
Other Operations
“CHILD LOCK” and “ON” appear in the
display panel.
You can only operate the system using the
buttons on the remote control.
To cancel, hold down x on the unit for
more than 5 seconds until “CHILD
LOCK” and “OFF” appear in the display
panel.
masterpage:Right
35GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\080ADD.fm]
Additional Information
Playable discs
• AUDIO CD
• CD-R/CD-RW
– audio data
– MP3 files that conform to ISO9660
Level 1/Level 2, or Joliet (expansion
format).
masterpage:Left
Music discs encoded with copyright
protection technologies
This product is designed to play back
discs that conform to the Compact Disc
(CD) standard. Recently, various music
discs encoded with copyright protection
technologies are marketed by some record
companies. Please be aware that among
those discs, there are some that do not
conform to the CD standard and may not
be playable by this product.
Notes
• MP3 (MPEG 1 Audio Layer-3) is a standard
format defined by ISO (International
Organization for Standardization) which
compresses audio data. MP3 files must be in
MPEG 1 Audio Layer-3 format.
• The system can only play back MP3 files that
have a file extension of “.mp3”.
Discs that cannot be played back
• CD-ROM
• CD-R/CD-RW which has the following
conditions:
– Recorded in MP3 PRO format
– Recorded in multisession that was not
ended by “closing the session”
– Recorded with an incompatible
recording device
– Poor recording quality
– Scratched or dirty
– Finalized incorrectly
• Discs of non-standard shape (e.g., heart,
square, star, etc.)
• Discs that have adhesive tape, paper, or
sticker attached to them
• Rental or used discs with attached seals
where the glue extends beyond the seal
• Discs that have labels printed using ink
that feels tacky when touched
Note on DualDiscs
A DualDiscs is a two sided disc product
which mates DVD recorded material on
one side with digital audio material on the
other side. However, since the audio
material side does not conform to the
Compact Disc (CD) standard, playback
on this product is not guaranteed.
Notes on playing multisession discs
• This system can play back multisession
discs when an MP3 file is contained in
the first session. Any subsequent MP3
files recorded in later sessions can also
be played back (If later sessions contain
AUDIO CD format, the system cannot
play back this multisession discs).
• If the first session is recorded in AUDIO
CD format, only the first session will be
played back.
Websites for
compatible devices
Check the websites below for the latest
information about compatible USB
devices and Bluetooth devices.
For customers in Latin America:
<http://esupport.sony.com/LA>
For customers in the United States:
<http://esupport.sony.com/>
For customers in Canada:
<http://esupport.sony.com/ca>
For customers in Europe:
<http://support.sony-europe.com/>
For customers in other countries/regions:
<http://www.sony-asia.com/support>
36GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\080ADD.fm]
Troubleshooting
Should you encounter a problem with
your system, find your problem in the
troubleshooting checklist below and take
the corrective action.
If the problem persists, consult your
nearest Sony dealer.
Note that if the service personnel changes
some parts during repair, these parts may
be retained.
If “PROTECT EXX” (X is a number)
appears in the display panel
Immediately unplug the power cord,
and check the following items.
• Are you using only the supplied
speakers?
• Is anything blocking the ventilation
holes of the unit?
After checking the above items and
fixing any problems, plug in the power
cord again and turn on the system. If
the issue persists, consult your nearest
Sony dealer.
The system has entered standby
mode.
• This is not a malfunction. The system
enters standby mode automatically in
about 15 minutes when there is no
operation or audio signal output (page 35).
The clock or timer setting is canceled.
• The power cord is disconnected or a power
failure occurred. Set the clock (page 16)
and timer (page 33) again.
There is no sound.
• Adjust the volume.
• Check the speaker connections (page 13).
• Check the connection of the optional
equipment, if any (page 13).
• Turn on the connected equipment.
• There is no audio output during Recording
Timer.
There is no microphone sound.
(SHAKE-99/SHAKE-77/SHAKE-55
only)
• Adjust the microphone volume.
• Make sure the microphone is connected to
the MIC jack correctly.
• Make sure the microphone is turned on.
There is severe hum or noise.
• Move the system away from sources of
noise.
• Connect the system to a different wall
outlet.
• Install a noise filter (commercially
available) to the power cord.
• Turn off surrounding electrical
equipment.
The timer does not function.
• Check the timer setting and set the correct
time (page 33).
• Cancel the Sleep Timer function
(page 33).
The remote control does not function.
• Remove the obstacles between the remote
control and the unit.
• Move the remote control closer to the unit.
• Point the remote control at the unit’s
sensor.
• Replace the batteries (R6/size AA).
• Move the unit away from the fluorescent
light.
There is acoustic feedback.
• Reduce the volume.
• (SHAKE-99/SHAKE-77/SHAKE-55
only) Move the microphone away from
the speakers or change the direction of the
microphone.
Additional Information
General
masterpage:Right
“PLEASE CONNECT ALL
SPEAKERS” appears. (SHAKE-99/
SHAKE-77/SHAKE-55 only)
• Check that all speakers are connected.
37GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\080ADD.fm]
“CHILD LOCK” appears when you
press any button on the unit.
• Set the Child Lock function to off
(page 35).
Speakers
Sound comes from only one channel
or the left and right volume is
unbalanced.
• Place the speakers as symmetrically as
possible.
• Check that the speakers are connected
securely and correctly.
• The source being played back is
monaural.
There is no sound from a specific
speaker.
• Check that the speaker is connected
securely and correctly.
Disc player
The disc tray does not open and
“LOCKED” appears in the display
panel.
masterpage:Left
The sound skips.
• Wipe the disc clean (page 42).
• Reload the disc.
• Move the unit to a place with no
vibration (e.g., on top of a stable stand).
• Move the speakers away from the unit,
or place them on separate stands. When
you listen to a track with bass sounds at
high volume, the speaker vibration may
cause the sound to skip.
Playback does not start from the first
track.
• Set the play mode to Normal Play
(page 18).
The folder name, track name, file
name and ID3 tag characters do not
appear properly.
• The ID3 tag is not Version 1(1.0/1.1) or
Version 2(2.2/2.3).
• The character codes that can be
displayed by this system are as follows:
– Upper cases (A to Z)
– Numbers (0 to 9)
– Symbols (< > * +, [ ] \ _)
Other characters appear as “_”.
• Consult your nearest Sony dealer or
local authorized Sony service facility.
USB device
The disc tray does not close.
Transferring results in an error.
• Load the disc correctly.
• You are using an unsupported USB
device. Check the information on the
website about compatible USB devices
(page 36).
• The USB device is not formatted
correctly. Refer to the operating
instructions of the USB device on how
to format.
• Turn off the system and remove the
USB device. If the USB device has a
power switch, turn the USB device off
and on again after removing it from the
system. Then, perform the transfer
again.
The disc does not eject.
• You cannot eject the disc during
CD-USB Synchronized Transfer or
REC1 Transfer. Press x to cancel the
transfer, then press Z OPEN/CLOSE
on the unit to eject the disc.
• Consult your nearest Sony dealer.
Playback does not start.
• Wipe the disc clean (page 42).
• Reload the disc.
• Load a disc that this system can play
back (page 36).
• Remove the disc and wipe away the
moisture on the disc, then leave the
system turned on for a few hours until
the moisture evaporates.
38GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\080ADD.fm]
• If the transfer and erase operations are
repeated multiple times, the file
structure within the USB device
becomes fragmented. Refer to the
operating instructions supplied with the
USB device on how to deal with this
problem.
• The USB device was disconnected or
the power was turned off during
transfer. Delete the partially-transferred
file, and perform the transfer again. If
this does not fix the problem, the USB
device may be broken. Refer to the
operating instructions of the USB
device on how to deal with this problem.
Audio files or folders on the USB
device cannot be erased.
• Check if the USB device is writeprotected.
• The USB device was disconnected or
the power was turned off during the
erase operation. Delete the partiallyerased file. If this does not fix the
problem, the USB device may be
broken. Refer to the operating
instructions of the USB device on how
to deal with this problem.
• The USB device is not connected
correctly. Turn off the system and
reconnect the USB device, then turn on
the system and check if “USB A” or
“USB B” lights up in the display panel.
There is noise, skipping, or distorted
sound.
• You are using an unsupported USB
device. Check the information on the
website about compatible USB devices
(page 36).
• Turn off the system and reconnect the
USB device, then turn on the system.
• The music data itself contains noise, or
the sound is distorted. Noise may have
entered during the transfer process.
Delete the file, and try transfer again.
• The bit rate used when encoding audio
files was low. Send audio files with
higher bit rate to the USB device.
“READING” is displayed for an
extended time, or it takes a long time
before playback starts.
• The reading process can take a long time
in the following cases.
– There are many folders or files on the
USB device (page 18).
– The file structure is extremely
complex.
– The memory capacity is excessive.
– The internal memory is fragmented.
“OVER CURRENT” appears.
• A problem has been detected with the
level of electrical current from the A
port or B port. Turn off the system
and remove the USB device from the
port. Make sure there is no problem with
the USB device. If this display pattern
persists, contact your nearest Sony
dealer.
Erroneous display.
• The data stored in the USB device may
have been corrupted, perform the
transfer again.
• The character codes that can be
displayed by this system are as follows:
– Upper cases (A to Z)
– Numbers (0 to 9)
– Symbols (< > * +, [ ] \ _)
Other characters appear as “_”.
The USB device is not recognized.
• Turn off the system and reconnect the
USB device, then turn on the system.
• Check the information on the website
about compatible USB devices
(page 36).
• The USB device does not work
properly. Refer to the operating
instructions of the USB device on how
to deal with this problem.
Additional Information
There is no sound.
masterpage:Right
Playback does not start.
• Turn off the system and reconnect the
USB device, then turn on the system.
• Check the information on the website
about compatible USB devices
(page 36).
39GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\080ADD.fm]
masterpage:Left
Playback does not start from the first
file.
• Turn off surrounding electrical
equipment.
• Set the play mode to Normal Play
(page 18).
Bluetooth device
Audio file cannot be played back.
• USB devices formatted with file
systems other than FAT16 or FAT32 are
unsupported.*
• A WMA audio file that is the WMA
DRM, WMA Lossless, or WMA PRO
format cannot be played back.
• An AAC audio file that is the AAC
DRM or AAC Lossless format cannot
be played back.
• AAC audio files encoded at 96 kHz
cannot be played back.
• If multiple partitions exist on a USB
device that is being used, files may not
be played back.
• The system can play back to a depth of
8 folders only.
• Files that are encrypted or protected by
passwords cannot be played back.
• Files with DRM (Digital Rights
Management) copyright protection
cannot be played back by this system.
• The MP3 PRO audio file can be played
back as MP3 audio file.
* This system supports FAT16 and FAT32, but
some USB devices may not support all of
these FAT. For details, refer to the operating
instructions of each USB device or contact the
manufacturer.
Tuner
There is severe hum or noise, or
stations cannot be received.
(“TUNED” or “ST” flashes in the
display panel.)
• Connect the antenna properly.
• Change the antenna location and its
orientation to obtain good reception.
• Connect a commercially available
external antenna.
• Consult your nearest Sony dealer if the
supplied AM antenna has come off from
the plastic stand.
Pairing cannot be performed.
• Move the Bluetooth device closer to the
system.
• Pairing may not be possible if other
Bluetooth devices are present around the
system. In this case, turn off the other
Bluetooth devices.
• Make sure the correct passkey was
entered at the Bluetooth device.
The Bluetooth device cannot detect
this unit, or “BT OFF” appears in the
display panel.
• Set the Bluetooth signal to “BT ON”
(page 28).
Connection is not possible.
• The Bluetooth device you attempted to
connect does not support the A2DP
profile, and cannot be connected with
the system.
• Enable the Bluetooth function of the
Bluetooth device.
• Establish a connection from the
Bluetooth device.
• The pairing registration information has
been erased. Perform the pairing
operation again.
• While connected to a Bluetooth device,
this system cannot be detected and a
connection cannot be established from
another Bluetooth device which is never
paired before.
• Erase the pairing registration
information of the Bluetooth device
(page 28) and perform the pairing
operation again (page 26).
The sound skips or fluctuates, or the
connection is lost.
• The system and the Bluetooth device are
too far apart.
• If there are obstacles between the
system and your Bluetooth device,
remove or avoid the obstacles.
40GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\080ADD.fm]
• If there is equipment that generates
electromagnetic radiation, such as a
wireless LAN, other Bluetooth device,
or a microwave oven nearby, move
them away.
The sound of your Bluetooth device
cannot be heard on this system.
• Increase the volume on your Bluetooth
device first, then adjust the volume
using VOLUME +/–.
There is severe hum, noise or
distorted sound.
• If there are obstacles between the
system and your Bluetooth device,
remove or avoid the obstacles.
• If there is equipment that generates
electromagnetic radiation, such as a
wireless LAN, other Bluetooth device,
or a microwave oven nearby, move
them away.
• Turn down the volume of the connected
Bluetooth device.
Party Chain
• Check the connections (page 31).
• Make sure the audio cords are connected
correctly.
“PARTY CHAIN” is flashing in the
display panel.
• AUDIO IN 1 function is selected during
Party Chain function. Press FUNCTION
repeatedly to select other function.
• Restart the system.
To reset the system
If the system still does not operate
properly, reset the system to factory
default settings.
Use the buttons on the unit to perform this
operation.
1 Unplug and plug the power cord
back in.
3 Hold down x and LED COLOR for
about 3 seconds.
“RESET” appears in the display panel.
All user-configured settings, such as
preset radio stations, timers, and the
clock are reset to factory default
setting.
Messages
One of the following messages may
appear or flash in the display panel during
operation.
CANNOT PLAY
A disc that cannot be played back was
inserted.
DEVICE ERROR
The USB device could not be recognized
or an unknown device is connected.
DEVICE FULL
The memory of the USB device is full.
FATAL ERROR
The USB device was removed during
transfer or erase operation, and may have
been damaged.
FOLDER FULL
You cannot transfer onto the USB device
because the number of folder has reached
its maximum.
NO DEVICE
No USB device is connected.
NO DISC
There is no disc on the disc tray.
Additional Information
Party Chain function cannot be
activated.
masterpage:Right
NO MEMORY
The memory selected for playback or
transfer has no memory media inserted in
the USB device.
NO STEP
All of the programmed steps have been
erased.
NO TRACK
No playable file is loaded in the system.
2 Press "/1 to turn on the system.
41GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\080ADD.fm]
NOT IN USE
You tried to perform a specific operation
under conditions where that operation is
prohibited.
masterpage:Left
Precautions
When carrying the unit
NOT SUPPORTED
An unsupported USB device is connected,
or the USB device is connected through a
USB hub.
Perform the following procedure to
protect the disc mechanism.
Use the buttons on the unit to perform this
operation.
OFF TIME NG
The on time and off time of Play Timer or
Recording Timer is the same.
1 Press "/1 to turn on the system.
2 Press CD.
3 Remove the disc.
PARTY GUEST
The system becomes a Party Guest when
Party Chain function is activated.
PARTY HOST
The system becomes a Party Host when
Party Chain function is activated.
PROTECTED
The USB device is write-protected.
PUSH STOP
You tried to perform an operation that can
be performed only when the playback is
stopped.
READING
The system is reading information of the
disc or USB device. Some operations are
not available.
REC ERROR
The transfer did not start, stopped
partway, or otherwise could not be
performed.
STEP FULL
You tried to program more than 25 steps.
TRACK FULL
You cannot transfer onto the USB device
because the number of file has reached its
maximum.
Press Z OPEN/CLOSE to open and
close the disc tray.
Wait until “NO DISC” appears in the
display panel.
4 Unplug the power cord.
Notes on discs
• Before playing, wipe the disc with a cleaning
cloth from the center outward to the edge.
• Do not clean discs with solvents, such as
benzine, thinner, or commercially available
cleaners or anti-static spray intended for vinyl
LPs.
• Do not expose discs to direct sunlight or heat
sources such as hot air ducts, nor leave it in a
car parked in direct sunlight.
On safety
• Completely disconnect the power cord (mains
lead) from the wall outlet (mains) if it is not
going to be used for an extended period of
time. When unplugging the unit, always grip
the plug. Never pull the cord itself.
• Should any solid object or liquid get into the
system, unplug the system, and have it
checked by qualified personnel before
operating it again.
• (USA and Canadian models only)
One blade of the plug is wider than other for
the purpose of safety and will fit to the wall
outlet only one way. If you are unable to insert
the plug fully into the outlet, contact your
dealer.
• AC power cord must be changed only at the
qualified service shop.
42GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\080ADD.fm]
On placement
• Do not place the system in an inclined
position or in locations that are extremely hot,
cold, dusty, dirty, or humid or lacking
adequate ventilation, or subject to vibration,
direct sunlight or a bright light.
• Be careful when placing the unit or speakers
on surfaces that have been specially treated
(for example, wax, oil, polish) as staining or
discoloration of the surface may result.
• If the system is brought directly from a cold to
a warm location or is placed in a very damp
room, moisture may condense on the lens
inside the unit, and cause the system to
malfunction. In this situation, remove the
disc, and leave the system turned on for about
an hour until the moisture evaporates.
On heat buildup
• Heat buildup on the unit during operation is
normal and is not a cause for alarm.
• Do not touch the cabinet if it has been used
continuously at a high volume because the
cabinet may have become hot.
• Do not obstruct the ventilation holes.
On the speaker system
Cleaning the cabinet
Clean this system with a soft cloth slightly
moistened with a mild detergent solution.
Do not use any type of abrasive pad, scouring
powder, or solvent, such as thinner, benzine,
or alcohol.
On Bluetooth Communication
• Bluetooth devices should be used within
approximately 10 meters (33 feet)
(unobstructed distance) of each other. The
effective communication range may become
shorter under the following conditions.
– When a person, metal object, wall or other
obstruction is between the devices with a
Bluetooth connection
– Locations where a wireless LAN is installed
– Around microwave ovens that are in use
– Locations where other electromagnetic
waves occur
• Bluetooth devices and wireless LAN
(IEEE 802.11b/g) use the same frequency
band (2.4 GHz). When using your Bluetooth
device near a device with wireless LAN
capability, electromagnetic interference may
occur. This could result in lower data transfer
rates, noise, or inability to connect. If this
happens, try the following remedies:
– Try connecting this system and Bluetooth
device when you are at least 10 meters
(33 feet) away from the wireless LAN
equipment.
– Turn off the power to the wireless LAN
equipment when using your Bluetooth
device within 10 meters (33 feet).
• The radio waves broadcast by this system may
interfere with the operation of some medical
devices. Since this interference may result in
malfunction, always turn off the power on this
system and Bluetooth device in the following
locations:
– In hospitals, on trains, in airplanes, at gas
stations, and any place where flammable
gases may be present
– Near automatic doors or fire alarms
• This system supports security functions that
comply with the Bluetooth specification as a
means of ensuring security during
communication using Bluetooth technology.
However, this security may be insufficient
depending on the setting contents and other
factors, so always be careful when performing
communication using Bluetooth technology.
• Sony cannot be held liable in any way for
damages or other loss resulting from
information leaks during communication
using Bluetooth technology.
• Bluetooth communication is not necessarily
guaranteed with all Bluetooth devices that
have the same profile as this system.
• Bluetooth devices connected with this system
must comply with the Bluetooth specification
prescribed by the Bluetooth SIG, Inc., and
must be certified to comply. However, even
when a device complies with the Bluetooth
specification, there may be cases where the
characteristics or specifications of the
Bluetooth device make it impossible to
connect, or may result in different control
methods, display or operation.
• Noise may occur or the audio may cut off
depending on the Bluetooth device connected
with this system, the communications
environment, or surrounding conditions.
Additional Information
This speaker system is not magnetically
shielded, and the picture on nearby TV sets may
become magnetically distorted. In this situation,
turn off the TV, wait 15 to 30 minutes, and turn
it back on. If there is no improvement, move the
speakers far away from the TV.
masterpage:Right
43GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\080ADD.fm]
Specifications
AUDIO POWER
SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
(USA model only)
SHAKE-99
With 10 ohm loads, both channels driven,
from 100 – 3,000 Hz; rated 500 watts per
channel minimum RMS power, with no
more than 0.7% total harmonic distortion
from 250 milliwatts to rated output.
SHAKE-55
With 4 ohm loads, both channels driven,
from 120 – 10,000 Hz; rated 180 watts per
channel minimum RMS power, with no
more than 0.7% total harmonic distortion
from 250 milliwatts to rated output.
SHAKE-33
With 4 ohm loads, both channels driven,
from 40 – 600 Hz; rated 180 watts per
channel minimum RMS power, with no
more than 0.7% total harmonic distortion
from 250 milliwatts to rated output.
Amplifier section
The following are measured at
USA and Canadian models:
AC 120 V, 60 Hz
Mexican model:
AC 120 V – 240 V, 60 Hz
European model:
AC 220 V – 240 V, 50/60 Hz
Chilean and Bolivian models:
AC 220 V – 240 V, 50 Hz
Other models:
AC 120 V – 240 V, 50/60 Hz
SHAKE-99
WF (Woofers)
Power Output (rated):
700 W + 700 W (at 10 ohms, 1 kHz,
1% THD)
masterpage:Left
RMS output power (reference):
900 W + 900 W (per channel at
10 ohms, 1 kHz)
MID (Mid speakers)/TW (Tweeters)
RMS output power (reference):
300 W + 300 W (per channel at
8 ohms, 2 kHz)
SW (Subwoofers)
RMS output power (reference):
1,200 W + 1,200 W (per channel at
8 ohms, 100 Hz)
SHAKE-77
WF (Woofers)/MID (Mid speakers)/
TW (Tweeters)
Power Output (rated):
350 W + 350 W (at 4 ohms, 1 kHz,
1% THD)
RMS output power (reference):
600 W + 600 W (per channel at
4 ohms, 1 kHz)
SW (Subwoofers)
RMS output power (reference):
1,200 W + 1,200 W (per channel at
8 ohms, 100 Hz)
SHAKE-55
WF (Woofers)/TW (Tweeters)
Power Output (rated):
350 W + 350 W (at 4 ohms, 1 kHz,
1% THD)
RMS output power (reference):
600 W + 600 W (per channel at
4 ohms, 1 kHz)
SW (Subwoofers)
RMS output power (reference):
900 W + 900 W (per channel at
10 ohms, 100 Hz)
SHAKE-33
WOOFERS
Power Output (rated):
350 W + 350 W (at 4 ohms, 100 Hz,
1% THD)
RMS output power (reference):
600 W + 600 W (per channel at
4 ohms, 100 Hz)
MID (Mid speakers)/TWEETERS
RMS output power (reference):
500 W + 500 W (per channel at
5 ohms, 1 kHz)
44GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\080ADD.fm]
Inputs
AUDIO IN 1/PARTY CHAIN IN L/R
Voltage 2 V, impedance 47 kilohms
AUDIO IN 2 L/R
Voltage 2 V, impedance 47 kilohms
MIC (SHAKE-99/SHAKE-77/SHAKE-55
only)
Sensitivity 1 mV, impedance
10 kilohms
(USB) A, (USB) B port
Type A
Outputs
AUDIO OUT/PARTY CHAIN OUT L/R
Voltage 2 V, impedance 1 kilohm
USB section
masterpage:Right
Disc player section
System
Compact disc and digital audio system
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6 W
* This output is the value measurement at
a distance of 200 mm from the objective
lens surface on the Optical Pick-up
Block with 7 mm aperture.
Frequency response
20 Hz – 20 kHz
Signal-to-noise ratio
More than 90 dB
Dynamic range
More than 88 dB
Supported bit rate
WMA:
48 kbps – 192 kbps, VBR, CBR
AAC:
48 kbps – 320 kbps, VBR, CBR
Sampling frequencies
WMA: 44.1 kHz
AAC: 44.1 kHz
Supported USB device
Mass Storage Class
Maximum current
500 mA
Tuner section
Disc/USB section
AM tuner section
Tuning range
European model:
531 kHz – 1,602 kHz (9 kHz step)
Pan American and Australian models:
531 kHz – 1,710 kHz (9 kHz step)
530 kHz – 1,710 kHz (10 kHz step)
Other models:
531 kHz – 1,602 kHz (9 kHz step)
530 kHz – 1,610 kHz (10 kHz step)
FM tuner section
Tuning range
USA and Canadian models:
87.5 MHz – 108.0 MHz (100 kHz step)
Other models:
87.5 MHz – 108.0 MHz (50 kHz step)
Additional Information
Supported bit rate
MPEG1 Layer-3:
32 kbps – 320 kbps, VBR
MPEG2 Layer-3:
8 kbps – 160 kbps, VBR
MPEG1 Layer-2:
32 kbps – 384 kbps, VBR
Sampling frequencies
MPEG1 Layer-3:
32 kHz/44.1 kHz/48 kHz
MPEG2 Layer-3:
16 kHz/22.05 kHz/24 kHz
MPEG1 Layer-2:
32 kHz/44.1 kHz/48 kHz
FM stereo, FM/AM superheterodyne tuner
Antenna:
FM lead antenna
AM loop antenna
Bluetooth section
Communication system
Bluetooth Standard version 3.1
Output
Bluetooth Standard Power Class 2
Maximum communication range
Line of sight approx. 10 m1)
45GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\080ADD.fm]
Frequency band
2.4 GHz band (2.4000 GHz –
2.4835 GHz)
Modulation method
FHSS (Freq Hopping Spread
Spectrum)
Compatible Bluetooth profiles2)
A2DP (Advanced Audio Distribution
Profile)
AVRCP 1.3 (Audio Video Remote
Control Profile)
SPP (Serial Port Profile)
Supported codecs
SBC (Sub Band Codec)
AAC (Advanced Audio Coding)
1)
The actual range will vary depending on
factors such as obstacles between devices,
magnetic fields around a microwave oven,
static electricity, reception sensitivity,
antenna’s performance, operating system,
software application, etc.
2)
Bluetooth standard profiles indicate the
purpose of Bluetooth communication between
devices.
Speakers
SS-SHAKE99 for SHAKE-99
Speaker system
4-way, Sound Pressure Horn and Bass
Reflex
Speaker unit
Woofers: 250 mm (9 7/8 in), cone type
Tweeters: 25 mm (1 in), horn type
Mid speakers: 100 mm (4 in), cone
type
Subwoofers: 460 mm (18 in), cone
type
Rated impedance
Mid speakers/tweeters: 8 ohms
Woofers: 10 ohms
Subwoofers: 8 ohms
Dimensions (w/h/d) (Approx.)
610 mm × 945 mm × 500 mm
(24 1/8 in × 37 1/4 in × 19 3/4 in)
Mass (Approx.)
51.0 kg (112 lb 7 oz)
Quantity: 2 pieces
masterpage:Left
SS-SHAKE77 for SHAKE-77
Speaker system
4-way, Sound Pressure Horn and Bass
Reflex
Speaker unit
Woofers: 200 mm (7 7/8 in), cone type
Tweeters: 25 mm (1 in), horn type
Mid speakers: 100 mm (4 in), cone
type
Subwoofers: 380 mm (15 in), cone
type
Rated impedance
Woofers/mid speakers/tweeters:
4 ohms
Subwoofers: 8 ohms
Dimensions (w/h/d) (Approx.)
510 mm × 783 mm × 450 mm
(20 1/8 in × 30 7/8 in × 17 3/4 in)
Mass (Approx.)
35.0 kg (77 lb 3 oz)
Quantity: 2 pieces
SS-SHAKE55 for SHAKE-55
Speaker system
3-way, Sound Pressure Horn and Bass
Reflex
Speaker unit
Woofers: 200 mm (7 7/8 in), cone type
Tweeters: 25 mm (1 in), horn type
Subwoofers: 350 mm (14 in), cone
type
Rated impedance
Woofers/tweeters: 4 ohms
Subwoofers: 10 ohms
Dimensions (w/h/d) (Approx.)
490 mm × 660 mm × 363 mm
(19 3/8 in × 26 in × 14 3/8 in)
Mass (Approx.)
26.0 kg (57 lb 6 oz)
Quantity: 2 pieces
SS-SHAKE33 for SHAKE-33
Speaker system
3-way, Sound Pressure Horn
Speaker unit
Woofers: 300 mm (12 in), cone type
Tweeters: 25 mm (1 in), horn type
Mid speakers: 100 mm (4 in), cone
type
46GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\080ADD.fm]
Rated impedance
Mid speakers/tweeters: 5 ohms
Woofers: 4 ohms
Dimensions (w/h/d) (Approx.)
410 mm × 610 mm × 376 mm
(16 1/4 in × 24 1/8 in × 14 7/8 in)
Mass (Approx.)
18.5 kg (40 lb 13 oz)
Quantity: 2 pieces
masterpage:Right
Supplied accessories
Remote control (1)
R6 (Size AA) batteries (2)
FM lead/AM loop antenna (1)
Bottom panel (1) (SHAKE-77/
SHAKE-55/SHAKE-33 only)
Design and specifications are subject to
change without notice.
General
Additional Information
Power requirements
USA and Canadian models:
AC 120 V, 60 Hz
Mexican model:
AC 120 V – 240 V, 60 Hz
European model:
AC 220 V – 240 V, 50/60 Hz
Chilean and Bolivian models:
AC 220 V – 240 V, 50 Hz
Other models:
AC 120 V – 240 V, 50/60 Hz
Power consumption
SHAKE-99: 700 W
SHAKE-77: 525 W
SHAKE-55: 500 W
SHAKE-33: 350 W
Power consumption (at the Power Saving
mode)
0.5 W (When “BT STANDBY” is set
to “STANDBY OFF”)
4 W (When “BT STANDBY” is set to
“STANDBY ON”)
Dimensions (w/h/d) (excl. speakers)
(Approx.)
SHAKE-99: 500 mm × 220 mm ×
380 mm (19 3/4 in × 8 3/4 in × 15 in)
SHAKE-77/SHAKE-55/SHAKE-33:
505 mm × 160 mm × 350 mm
(20 in × 6 3/8 in × 13 7/8 in)
Mass (excl. speakers) (Approx.)
SHAKE-99: 10.0 kg (22 lb 1 oz)
SHAKE-77/SHAKE-55: 7.6 kg
(16 lb 13 oz)
SHAKE-33: 7.0 kg (15 lb 7 oz)
47GB
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB
filename[D:\NORM'S JOB\SONY HA\SO130078\SHAKE-99_77_55_33 (PMRF
01)\4487569121_GB\090BPG.fm]
masterpage:Bcov
©2014 Sony Corporation Printed in Malaysia
model name [SHAKE-99/SHAKE-77/SHAKE-55/SHAKE-33]
[4-487-569-12(1)] GB