Sharp PN-K322B touch screen monitor

PN-K322B
LCD MONITOR
OPERATION MANUAL
IMPORTANT:
To aid reporting in case of loss or theft, please record the
product’s model and serial numbers in the space provided.
The numbers are located in the rear of the product.
Model No.:
Serial No.:
U.S.A. ONLY
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within
a triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the
manufacturer could void the user’s authority to operate this equipment.
NOTE:
This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
U.S.A. ONLY
3
E
DEAR SHARP CUSTOMER
Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your
product, please read the Safety Precautions carefully before using this product.
SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can
result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing,
operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the
following precautions carefully before using the product.
1. Read instructions — All operating instructions must be read and understood before the product is operated.
2.Keep this manual in a safe place — These safety and operating instructions must be kept in a safe place for future
reference.
3. Observe warnings — All warnings on the product and in the instructions must be observed closely.
4. Follow instructions — All operating instructions must be followed.
5.Cleaning — Unplug the power cord from the AC outlet before cleaning the product. Use a dry cloth to clean the product. Do
not use liquid cleaners or aerosol cleaners.
6.Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result
in accidents.
7.Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto
it. Be careful of equipment which drains water such as an air-conditioner.
8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.
Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life
of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings.
Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
9.Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from
resting on them.
10.The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with
impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.
11. Overloading — Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.
12.Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage flows in
the product, and inserting an object can cause electric shock and/or short internal parts.
For the same reason, do not spill water or liquid on the product.
13.Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other
dangerous conditions. Request a qualified service person to perform servicing.
14.Repair — If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service
person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls
not described in the instructions can cause damage, which often requires extensive adjustment work by a qualified
technician.
e. When the product has been dropped or damaged.
f.When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product
needs servicing.
15.Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement
parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of
unauthorized parts can result in fire, electric shock and/or other danger.
16.Safety checks — Upon completion of service or repair work, request the service technician to perform safety checks to
ensure that the product is in proper operating condition.
17.Wall mounting — When mounting the product on a wall, be sure to install the product according to the method
recommended by the manufacturer.
18.Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).
19.Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury,
severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and
missile launch control in a weapon system.
20.Do not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in
low-temperature burns.
E
4
SAFETY PRECAUTIONS (Continued)
WARNING:
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate counter measures.
To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: HDMI input terminal
and DisplayPort input terminal.
If a monitor is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries,
particularly to children, can be avoided by taking simple precautions such as:
• Using fixing devices like wall mount brackets recommended by the manufacturer.
• Only using furniture that can safely support the monitor.
• Ensuring the monitor is not overhanging the edge of the supporting furniture.
• Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the
monitor to a suitable support.
• Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.
• Educating children about the dangers of climbing on furniture to reach the monitor or its controls.
Especially for child safety
- Don’t allow children to climb on or play with the monitor.
- Don’t place the monitor on furniture that can easily be used as steps, such as a chest of drawers.
- Remember that children can become excited while watching a program, especially on a “larger than life” monitor. Care
should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.
- Care should be taken to route all cords and cables connected to the monitor so that they cannot be pulled or grabbed by
curious children.
5
E
TIPS AND SAFETY INSTRUCTIONS
- The TFT color LCD panel used in this monitor is made with
the application of high precision technology. However, there
may be minute points on the screen where pixels never light
or are permanently lit. Also, if the screen is viewed from
an acute angle there may be uneven colors or brightness.
Please note that these are not malfunctions but common
phenomena of LCDs and will not affect the performance of
the monitor.
- Do not display the same image for an extended time.
Displaying the same image for an extended time may cause
a residual image. In particular, an image with strong contrast
may cause a residual image after several hours.
- Never rub or tap the monitor with hard objects.
- Please understand that SHARP CORPORATION bears no
responsibility for errors made during use by the customer or
a third party, nor for any other malfunctions or damage to this
product arising during use, except where indemnity liability is
recognized under law.
- This monitor and its accessories may be upgraded without
advance notice.
- Do not use the monitor where there is a lot of dust, where
humidity is high, or where the monitor may come into contact
with oil or steam, as this could lead to fire.
- Ensure that the monitor does not come into contact with
water or other fluids. Ensure that no objects such as paper
clips or pins enter the monitor as this could lead to fire or
electric shock.
- Do not place the monitor on top of unstable objects or in
unsafe places. Do not allow the monitor to receive strong
shocks or to strongly vibrate. Causing the monitor to fall or
topple over may damage it.
-D
o not use the monitor near heating equipment or in places
where there is likelihood of high temperature. Do not use in an
environment where there are corrosive gases (sulfur dioxide,
hydrogen sulfide, nitrogen dioxide, chlorine, ammonia, ozone,
etc.). As this may lead to generation of excessive heat and
outbreak of fire.
- Do not use the monitor in places where it may be exposed to
direct sunlight.
- Images cannot be rotated on this monitor.
When using in portrait orientation, you will need to prepare
appropriately orientated content in advance.
- The AC outlet shall be installed near the equipment and shall
be easily accessible.
- Do not touch the screen when starting the LCD monitor. If
the screen is touched, the monitor may not function correctly.
In this situation, turn the LCD monitor off, wait at least 5
seconds, and then turn on the monitor again.
- Do not operate the screen with a hard or pointed object such
as a fingernail, pen other than the supplied touch pen, or a
pencil.
- Depending on the application used, the supplied touch pen
may not function.
- If another USB device is connected to the computer to which
the touch panel is connected, do not operate the USB device
during touch panel input. Input may not take place correctly.
- Do not use liquid such as alcohol in cleaning the screen.
- Keep all cables off the touch panel. Not doing so may lead to
LCD monitor malfunctions.
- If used in a room (or location) with drastic temperature
differences, the display quality of the screen and the quality
of touch panel performance may decrease.
E
6
The Power Cord and AC adapter
-U
se only the power cord and AC adapter supplied with the monitor.
- When handling the AC adapter, observe the following:
Incorrect handling may result in fire, electric shock, or injury.
•Do not drop the AC adapter or subject it to impact.
•Never disassemble the AC adapter. It contains high voltage
parts that are dangerous to touch.
•The AC adapter is for indoor use only. Do not use it outside.
•Do not use the supplied AC adapter with other devices.
-D
o not damage the power cord and AC adapter nor place heavy
objects on it, stretch it or over bend it. Also, do not add extension
cords. Damage to the cord may result in fire or electric shock.
-D
o not use the power cord with a power tap.
Adding an extension cord may lead to fire as a result of overheating.
- Do not remove or insert the power plug with wet hands.
Doing so could result in electric shock.
- Unplug the power cord if it is not used for a long time.
-D
o not attempt to repair the power cord if it is broken or
malfunctioning. Refer the servicing to the service representative.
- Do not stay in contact with the parts of the product and the
AC adapter that become hot for long periods of time.
Doing so may result in low-temperature burns.
-D
o not fasten the AC adapter to the monitor or other equipment.
Doing so may result in fire and electrical shock.
Manual Scope
- Microsoft, Windows and Internet Explorer are registered
trademarks of Microsoft Corporation.
-T
he terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
- DisplayPort is a registered trademark of Video Electronics
Standards Association.
- Adobe, Acrobat, and Reader are either registered trademarks
or trademarks of Adobe Systems Incorporated in the United
States and/or other countries.
- Intel, Celeron, and Intel Core 2 Duo are trademarks or
registered trademarks of Intel Corporation or its subsidiaries
in the U.S.A. and other countries.
- AMD, AMD Sempron, AMD Athlon, and combinations thereof
are trademarks of Advanced Micro Devices, Inc.
- This product comes with RICOH Bitmap Fonts produced and
sold by RICOH COMPANY, LTD.
- All other brand and product names are trademarks or
registered trademarks of their respective holders.
- Language of OSD menu used in this manual is English by
way of example.
- Illustrations in this manual may not exactly represent the
actual product or display.
- This manual assumes use in landscape orientation, except
where specifically noted.
LED Backlight
● The LED backlight in this product has a limited lifetime.
* If the screen gets dark or does not turn on, it may be
necessary to replace the LED backlight. This LED backlight
is exclusive to this product and must be replaced by an
authorized Sharp servicing dealer or service center.
* Please contact your local Sharp servicing dealer or
service center for assistance.
MOUNTING PRECAUTIONS
• This product is for use indoors.
• A mounting bracket compliant with VESA specifications is
required.
• To install on a stand (commercially available) or on a wall,
or to remove or move the monitor, consult your dealer.
• Mounting the monitor on the wall requires special expertise
and the work must be performed by an authorized SHARP
dealer. You should never attempt to perform any of this
work yourself. Our company will bear no responsibility
for accidents or injuries caused by improper mounting or
mishandling.
• Use the monitor with the surface perpendicular to a level
surface. If you are tilting the monitor without using the
supplied stand, the monitor may be tilted up to 25 degrees
upward or 20 degrees downward.
• This monitor should be used at an ambient temperature
between 41°F (5°C) and 95°F (35°C). Provide enough
space around the monitor to prevent heat from
accumulating inside.
For the monitor in landscape orientation
• When installing the
monitor in landscape
orientation, you can attach
the supplied horizontal
sticker (operation buttons)
to the front.
Horizontal sticker
(Operation
buttons)
• Use the supplied vertical sticker when you install the
monitor in portrait orientation.
Attach the vertical sticker (Operation buttons) to
the back or the front.
• Back
Vertical sticker (Operation buttons)
Unit: inch [cm]
7-7/8 [20]
2
[5]
• Front
1/8 [3.5]
Vertical sticker (Blank)
2
[5]
2 [5]
For the monitor in portrait orientation
Unit: inch [cm]
7-7/8 [20]
2
[5]
1/8 [3.5]
2
[5]
Vertical sticker (Operation buttons)
2 [5]
For the monitor on the supplied stand
Unit: inch [cm]
2
[5]
27-19/64
[69.3]
2
[5]
Cover
Sharp logo
Vertical sticker (Logo)
• If it is difficult to provide sufficient space for any reason
such as the installation of the monitor inside a housing, or
if the ambient temperature may be outside of the range
of 41°F (5°C) to 95°F (35°C), install a fan or take other
measures to keep the ambient temperature within the
required range.
• Do not block any ventilation openings. If the temperature
inside the monitor rises, this could lead to a malfunction.
• Do not place the monitor on a device which generates heat.
Caution
• Adhere to the following when installing the monitor in its
portrait orientation. Failing to adhere to the following may
cause malfunctions.
- Install the monitor such that the operation buttons are
located on the top side.
- Set the MONITOR on the MONITOR menu to PORTRAIT.
(See page 23.)
7
E
Contents
IMPORTANT INFORMATION.............................................3
DEAR SHARP CUSTOMER...............................................4
SAFETY PRECAUTIONS...................................................4
TIPS AND SAFETY INSTRUCTIONS................................6
MOUNTING PRECAUTIONS.............................................7
Supplied Components......................................................8
System Requirements......................................................9
Part Names......................................................................10
Adjustment of monitor position.................................... 11
Connecting Peripheral Equipment................................12
Connection with a PC or AV equipment......................12
Connecting the Power Cord..........................................13
Binding Cables................................................................14
Turning Power On/Off.....................................................15
Turning on the main power.........................................15
Turning power on/off...................................................15
Basic Operation..............................................................16
Touch Action...................................................................18
Touch action modes....................................................18
Status display of touch operation mode......................18
Touch action................................................................18
Other functions............................................................20
Cautionary points........................................................20
Menu Items......................................................................21
Displaying the menu screen........................................21
Menu item details........................................................22
Initialization (Reset)/Functional Restriction Setting
(FUNCTION).....................................................................26
Controlling the Monitor with a PC (RS-232C)...............27
PC connection.............................................................27
Communication conditions..........................................27
Communication procedure..........................................27
RS-232C command table............................................29
Troubleshooting..............................................................33
Specifications ................................................................35
Mounting Precautions
(For SHARP dealers and service engineers)................40
For information on the Pen Software, see the Pen Software Operation Manual.
Supplied Components
If any component should be missing, please contact your dealer.
 Liquid Crystal Display Monitor: 1
 Touch pen: 1
 Cable cover: 1
 Power cord: 1
 AC adapter: 1
 CD-ROM (Utility Disk for Windows): 1
 Setup Manual: 1
 DisplayPort cable: 1
 RS-232C conversion cable (Φ3.5 mini-jack): 1
 USB cable (for touch panel, miniB): 1
 Cable clamp: 2
 Cable clamp (small): 1
 Cable clamp (large): 3
 Anti-toppling clamp: 2
 Screws (for anti-toppling) (M4 x 10): 2
 Vertical sticker (Logo): 1
 Vertical sticker (Operation buttons): 1
 Vertical sticker (Blank): 1
 Horizontal sticker (Operation buttons): 1
 Cover Sharp logo: 1
Place this sticker onto the SHARP logo to cover the logo.
* Sharp Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.
E
8
System Requirements
nTouch Panel
To use the touch panel, the monitor must be connected to a computer using a USB cable.
Touch panel operating conditions are as described below.
Computer
PC/AT compatible computer with a USB 1.1 port.
OS
Windows 8 (32-bit or 64-bit version), Windows 7 (32-bit or 64-bit version), Windows Vista (32-bit or
64-bit version), Windows XP (32-bit or 64-bit version)
• Windows 7 or later is recommended for touch action.
• On Windows 7 and later, the touch panel operates with the standard Window driver. On Windows Vista/XP, you must install
the touch panel driver to your PC from the supplied CD-ROM.
n Pen Software
Operating conditions for the supplied Pen Software are as described below. To install Pen Software, refer to the Pen Software
Operation Manual. Pen Software is for use with monitors installed in landscape orientation.
Computer
PC/AT compatible computer able to output a resolution of 3840 x 2160.
(CD-ROM drive required for software installation.)
OS
Windows 8 (32-bit or 64-bit version), Windows 7 (32-bit or 64-bit version), Windows Vista (32-bit or
64-bit version), Windows XP (32-bit or 64-bit version)
CPU
Intel Celeron or AMD Sempron 1.6 GHz or faster
Intel Core 2 Duo or AMD Athlon II X2 2.8 GHz or faster recommended
Memory
At least 2 GB (at least 1 GB for Windows XP)
Free space on hard drive
At least 100 MB (free space separately required for data storage)
9
E
Part Names
nFront view
1. LCD panel
2. Power LED (See page 15.)
1
2
nRear view
2
3
4
14
15
16
17
18
19
20
5
6
7
8
9
10
11 12
1. Stand
2. Speakers
3. Vents
4. RS-232C input terminal (See page 12.)
5. PC/AV HDMI 1 input terminal (See page 12.)
6. PC/AV HDMI 2 input terminal (See page 12.)
7. DisplayPort input terminal (See page 12.)
8. Audio input terminal (See page 12.)
9. USB (mini-B) port (See page 12.)
10. Headphone terminal (See page 12.)
E
10
13
1
3
1. AC input terminal (See page 13.)
1
12. Main power switch (See page 15.)
13. Anti-theft hole ( )
14. Power button ( ) (See page 16.)
15. Brightness adjustment button ( ) (See page 16.)
16. Brightness adjustment button ( ) (See page 16.)
] button (See page 16.)
17. [VOL+/
18. [VOL-/
] button (See page 16.)
19. [MENU/ENTER] button (See page 16.)
20. [INPUT/RETURN] button (See page 16.)
Adjustment of monitor position
You can slide the monitor to adjust its position.
Use the monitor in the perpendicular position (about 90° from horizontal, Fig. A below) or slid to the bottommost position (about
25° from horizontal, Fig. B below). If used in any other position, the monitor may slide while in use.
A
A
B
B
25°
When moving the monitor from the position of Fig. B to the position of Fig. A above, slightly lift the monitor (1) and slide toward
the back (2).
(2)
(1)
Caution
• When sliding the monitor, be sure to grasp only the frame on the left and right sides.
- Take care not to pinch your fingers.
- Grasping and applying pressure to the LCD panel may damage it.
- Take care not to press any buttons. This may cause the volume or other settings to change.
11
E
Connecting Peripheral Equipment
1
2
3
4
5
6
7
Caution
• Be sure to turn off the main power switch and disconnect
the plug from the power outlet before connecting/
disconnecting cables. Also, read the manual of the
equipment to be connected.
• Be careful not to confuse the input terminal with the output
terminal when connecting cables. Accidentally reversing
cables connected to the input and output terminals may
cause malfunctions and the other problems.
• Do not use any cable that has a damaged or deformed
terminal. Using such a cable may cause malfunctions.
• Images may not be displayed properly depending on the
computer (video cards), cables, or peripheral devices to be
connected.
TIPS
• The audio input terminals used in each input mode are
factory-set as follows.
Input mode
DisplayPort
HDMI1 [PC], HDMI1 [AV]
HDMI2 [PC], HDMI2 [AV]
Audio input terminal
(Factory setting)
DisplayPort input terminal
PC/AV HDMI input terminal
4. DisplayPort input terminal
• Use the supplied DisplayPort cable.
• Select the audio input terminal to be used in DisplayPort
of AUDIO SELECT on the SETUP menu.
When DisplayPort is selected, connection to the audio
input terminal is unnecessary.
*Use the supplied cable.
*If you need to extend the cable, consult your dealer.
5. Audio input terminal
• Use a commercially available audio cable (mini stereo
jack) without resistance.
• Set the audio input terminal used for each input mode in
AUDIO SELECT on the SETUP menu.
6. USB (mini-B) port
• To use the touch panel, connect the touch panel to your
computer with the provided USB cable.
7. Headphone terminal
• Use commercially available headphones (mini stereo
jack).
• The output sound varies depending on the input mode.
• The volume can be adjusted using the volume adjustment.
TIPS
Connection with a PC or AV equipment
1.RS-232C input terminal
• The monitor can be connected to a PC using the RS232C conversion cable (supplied) and a commercially
available RS-232 straight cable to control the monitor
from the PC.
2. PC/AV HDMI1 input terminal
3. PC/AV HDMI2 input terminal
• Use a commercially available HDMI cable (High Speed
cable compliant).
• Set HDMI1, HDMI2, or HDMI DUAL in INPUT SELECT
on the SETUP menu according to the device to be
connected.
• Select the audio input terminal to be used in HDMI1
[AV], HDMI1 [PC], HDMI2 [AV], or HDMI2 [PC] of AUDIO
SELECT on the SETUP menu.
When HDMI1 or HDMI2 is selected, connection to the
audio input terminal is unnecessary.
E
12
• The length of the signal cables or surrounding environment
may affect the image quality.
• Video output is disabled in the following cases:
When the power is turned off
When the monitor is in input signal waiting mode
Connecting the Power Cord
Caution
• Use only the power cord and AC adapter supplied with the monitor.
1. Turn off the main power switch.
2. Connect the AC adapter (supplied) to the power cord (supplied).
3. Connect the AC adapter (supplied) to the AC input terminal.
4. Plug of the power cord (supplied) into the AC power outlet.
3
4 For power
outlet
AC input terminal
2
Power cord
(Supplied)
AC Adapter (Supplied)
Main power switch
1
TIPS
• Be sure to clamp the AC adapter cable (supplied) onto the cable clamp attachment using the supplied cable clamp.
When clamping the AC adapter cable, take care not to stress the terminal of the AC adapter cable. Do not bend the AC
adapter cable excessively.
Operation buttons
Cable
clamp
attachment
AC adapter cable (Supplied)
Caution
• Do not fasten the supplied AC adapter to the monitor or other equipment.
13
E
Binding Cables
nFastening the cables
The cables connected to the terminals on the rear of the monitor can be fastened with the cable clamp.
Attach the cable clamps to the attachment parts on the back of the monitor and the stand, and bind the cables.
Cable
Cable clamp
attachment
Cable clamp
Cable clamp (large)
Cable clamp (small)
Cable clamp
attachment
Cable
Cable clamp
attachment
Cable
nStoring the cables
After you have secured the cables connected to the back of the monitor with the cable clamp, you can store the cables in the
cable cover.
How to attach the cable cover
The tab inserts
into the hole to
hold the cable
cover
The cable cover
is attached by
hanging from the
hooks
How to remove the cable cover
Slightly lift the cable cover,
and with the tab clear of
the hole, move up and
remove
Caution
• Do not forcibly bend or apply force to the cables. Risk of wire breakage or other damage.
• When attaching the cable cover, do not pinch the cables.
• Arrange the cable to allow for use with the monitor slid to the bottommost position (about 25° from horizontal).
E
14
Turning Power On/Off
Caution
• Turn on the monitor first before turning on the PC or
playback device.
Turning on the main power
Turning power on/off
Press the power button ( ) to turn the power ON/OFF.
To turn off the power, press and hold down the power button (
for about 2 seconds.
)
Power button ( )
Power LED
Power lamp status
Main power switch
Caution
• The main power must be turned on/off with the main power
switch. Do not connect/disconnect the power cord or turn
the breaker on/off while the main power switch is on.
• When switching the main power switch off and back on,
always wait for at least 5 seconds.
• For a complete electrical disconnection, pull out the main
plug.
Status of the monitor
Green lit
Power on
Off
Power off (Standby mode)
Orange lit
Input signal waiting mode
Caution
• When switching the power button ( ) off and back on,
always wait for at least 5 seconds. A short interval may
result in a malfunction.
TIPS
• When the main power switch is off, the monitor cannot be
turned on.
• If the monitor is in the input signal standby mode and you
press the power button ( ), the monitor enters standby
mode.
15
E
Basic Operation
6. [MENU/ENTER] button
Displays and turns off the menu screen. (See page 21.)
1
Settings can be entered when the menu screen is displayed.
7. [INPUT/RETURN] button
The input selection menu is displayed.
Press the [VOL+/
]/[VOL-/
] buttons to select the input
mode, and press [INPUT/RETURN] button to enter.
2
3
Input mode
4
DisplayPort
HDMI1 [PC]
HDMI1 [AV]
5
HDMI2 [PC]
HDMI2 [AV]
6
Input mode
DisplayPort
HDMI DUAL [PC]*4
HDMI DUAL [AV]*4
1. Power button ( )
• The power can be turned on and off.
To turn off the power, press and hold down the power
button ( ) for about 2 seconds.
• The touch operation mode icon appears.
When the power button ( ) is pressed with the power on*,
the touch mode icon appears. For information on touch
operation mode, see page 18.
*If the power button ( ) is held down for about 2 seconds,
the power will turn off.
2,3. Brightness adjustment button (
The brightness menu appears.
BRIGHT
/
)
15
Adjust the brightness with the brightness adjustment button
/
).
(
*If you do not press any buttons for about 4 seconds, the
BRIGHT menu automatically disappears.
Move the cursor left or right in the menu screen, and increase
or decrease the setting.
*The cursor moves right when the brightness adjustment
button (
) is pressed, and left when the brightness
adjustment button (
) is pressed.
]/[VOL-/
] button
4,5. [VOL+/
The volume menu appears.
VOLUME
15
Adjust the volume with the [VOL+/
]/[VOL-/
] buttons.
*If you do not press any buttons for about 4 seconds, the
VOLUME menu automatically disappears.
Move the cursor up or down in the menu screen, and increase
or decrease the setting.
*The cursor moves up when the [VOL+/
] button is
pressed, and down when the [VOL-/
] button is pressed.
16
Audio
PC/AV HDMI input terminal*1
*3
PC/AV HDMI input terminal*2
When HDMI DUAL is set to ON
7
E
Video
DisplayPort input terminal
Video
Audio
DisplayPort input terminal
*3
PC/AV HDMI input terminal*4
*5
*1 Select the terminal to be used in HDMI1 of INPUT
SELECT. (See page 23.)
*2 Select the terminal to be used in HDMI2 of INPUT
SELECT. (See page 23.)
*3 Select the terminal for AUDIO SELECT which is used for
audio input. (See page 23.)
*4 Same as the HDMI1 terminal setting.
*5 Same as the AUDIO SELECT of HDMI1.
• When the [INPUT/RETURN] button is pressed in a menu
screen, the cursor returns to the previous screen.
• If the [INPUT/RETURN] button is pressed when the touch
mode icon appears, the touch mode icon will disappear.
Basic Operation
nSwitching the screen size
Even when the screen size is changed, the display may remain the same depending on the input signal.
WIDE
NORMAL
Dot by Dot
PC input
Displays image so it fills the entire screen.
AV input
An image with a 4:3 aspect ratio is stretched to fill the entire
screen.
PC input
Displays image so it fills the screen without changing the aspect
ratio of the input signals.
AV input
Displays the entire image of the aspect ratio of 4:3 without
changing the aspect ratio.
PC input
Displays the dots of the signals input from the connected PC as
the corresponding dots on the screen.
AV input
Displays at the number of panel pixels of the resolution of the input
signal.
TIPS
• Using this monitor’s screen-size switching to compress or expand the screen for commercial or public viewing in
establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright Law, so please be
careful.
• When PbyP mode is set to ON, the screen size cannot be changed.
• The appearance of the original video may change if you select a screen size with a different aspect ratio than the original
image (e.g. TV broadcast or video input from external equipment).
• When a non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this monitor, the
edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen size to
“NORMAL”.
• When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen
size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the
edges of the screen. This is due to the characteristics of the software, and is not a malfunction.
• Depending on the original image size, black bands may remain at the edges of the screen.
17
E
Touch Action
Touch action modes
Status display of touch operation mode
Touch operation modes are finger/pen mode, pen-only mode,
and finger-only mode. The mode can be changed in the touch
operation mode icon screen.
The monitor is set to finger/pen mode when shipped.
Monitor status is displayed at the right of the screen.
1. When the power button ( ) is pressed* with the power
on, the touch mode icon will appear.
*If the power button ( ) is held down for about 2 seconds,
the power will turn off.
3 2 1
2. Touch the icon.
A ( ) mark is displayed at the top of the icon for the
selected mode.
The mode can be checked with the touch mark located at
the right portion of the screen.
1
Finger/pen mode
In this mode, the screen can be touched with your finger or
with the touch pen.
While the screen is being touched with the touch pen,
touch pen operation is given priority and you cannot touch
the screen with your finger.
Once the touch pen has been moved away from the screen
for around 1 second, you can touch the screen with your
finger.
The touch mark becomes the finger/pen mark
.
2
Pen-only mode
This mode is for touch pen use only. You cannot touch the
screen with your finger.
The touch mark becomes the pen mark
.
3
Finger-only mode
This mode is for finger use only. You cannot touch the
screen with the touch pen.
The touch mark becomes the finger-only mark
.
TIPS
• If you take no action for about 1 minute while the touch
operation mode icon appears, the icon will automatically
disappear.
E
18
Touch Mark
Touch Mark
The touch mark displays the current touch action mode.
Finger/pen mode
This mark is displayed during finger/pen mode.
Pen-only mode
This mark is displayed during pen-only mode.
Finger-only mode
This mark is displayed during finger-only mode.
The touch mark is displayed for about 5 seconds. The setting
can be changed so that the touch mark always appears. (See
page 23.)
The display position of the touch mark can be changed.
(See page 23.)
Touch action
Touch actions that can be used with this monitor differ
according to operating system and application. The functions
of touch actions are also different. For details, check Windows
Help and the application’s support documentation.
Windows 8
Windows 7
Windows Vista*
Windows XP*
Single-tap
Yes
Yes
Yes
Double-tap
Yes
Yes
Yes
Swipe
Yes
Yes
Yes
Swipe from edge
of screen
Yes
No
No
Drag-and-drop
Yes
Yes
Yes
Slide to pan
Yes
Yes
No
Flicks
Yes
Yes
No
Press-and-hold
Yes
Yes
Yes
Zoom
Yes
Yes
No
Press-and-tap
No
Yes
No
Rotate
Yes
Yes
No
OS
Touch action
* You must install the touch panel driver to your PC from the
supplied CD-ROM.
Installation is not necessary in Windows 8 and Windows 7.
TIPS
• In Windows 7, if the checkmark has been removed from
“Enable multi-touch gestures and inking” in “Pen and touch”
in Control Panel, select the checkbox.
Touch Action
nCommon finger and touch pen actions
Single-tap
Touch the screen with your finger/touch pen.
Double-tap
Quickly touch the screen twice with your finger/touch pen.
Drag-and-drop
Touch the screen with your finger/pen and move without lifting.
When you have finished the movement, lift your finger/touch
pen.
Slide to pan
With your finger/touch pen touching the screen, move it up
and down to scroll the screen.
Swipe
Touch the screen with your finger/touch pen, move without
lifting, and then stop.
Flicks
Move your finger/touch pen in a flicking motion.
Flick your finger
Swipe from edge of screen
After touching the edge of the monitor with your finger/touch
pen, move horizontally without releasing your finger/touch pen
and then stop.
Press-and-hold
Press briefly with your finger/touch pen, and then lift your
finger/touch pen from the screen.
19
E
Touch Action
nFinger actions
Other functions
Zoom
While touching the screen with two fingers, move them closer
together and farther apart.
In Windows 8, input panel functions can be used.
In Windows 7, touch pointer and input panel functions can be
used.
For information about the touch pointer and input panel
functions, see Windows Help.
Touch pointer :
A translucent image of a mouse appears near the point
touched. The left/right buttons of the image can be clicked
to perform the same actions as left/right clicking a mouse.
Pinch
Input panel :
A software keyboard and an input panel with handwriting
recognition appear on the screen.
Windows 8 and Windows 7 (excluding Starter), the ink
function of Microsoft Office can be used.
Handwritten comments can be written, and handwriting can
be recognized.
For details, see Microsoft Office Help.
Cautionary points
Stretch
Press-and-tap
With one finger touching the screen, tap once (single tap) with
another finger.
Tap once (single tap) with another finger
With one finger touching
Rotate
While touching the monitor with one finger, move the other
finger in the direction you wish to rotate in.
Move another finger in the desired direction of rotation
With one finger touching
E
20
• When performing touch actions, use the ball of your finger.
• When performing pen actions, use the supplied touch pen.
• Do not use the touch pen for any purpose other than touch
panel operation.
• Do not press hard on the tip of the touch pen.
• If there is dirt or foreign matter on the tip of the touch pen,
remove it. Failure to do so may damage the screen.
• Even when in pen-only mode, the monitor may respond to
objects other than the supplied touch pen.
• Touch operation is not possible when screen motion is
enabled or when PbyP mode is set to ON.
• When performing pen actions with the supplied touch pen,
avoid touching the screen with your other hand as this may
affect touch screen response.
If your other hand touches the screen, pen operation will
not be possible where the hand areas overlap, as shown
below.
Pen operation will be possible when you remove your other
hand from the screen.
• The touch coordinates may shift depending on the video
output settings on the computer.
Menu Items
Displaying the menu screen
TIPS
Video adjustment and settings of various functions are
enabled. This section describes how to use the menu items.
See pages 22 to 24 for details of each menu items.
nMenu screen display
Caution
• Do not turn the main power switch off while the menu items
are being displayed. Doing so may initialize the settings.
nExample of operation
PICTURE
SETUP
MONITOR
PbyP
OTHERS
31
CONTRAST
BLACK LEVEL
30
30
TINT
COLORS
30
30
SHARPNESS
COLOR ADJUSTMENT
12
3840x2160
OK···[ENTER]
V: 30Hz H: 69.5kHz
END···[RETURN]
2. Press [VOL+/
]/[VOL-/
] button to select PICTURE,
and press [MENU/ENTER] button.
MONITOR
PbyP
OTHERS
PbyP
OTHERS
]/[VOL-/
2
PICTURE
DisplayPort
BRIGHT
31
CONTRAST
BLACK LEVEL
30
30
TINT
COLORS
30
30
SHARPNESS
COLOR ADJUSTMENT
12
ADVANCED
RESET
V: 30Hz
H: 69.5kHz
BACK···[RETURN]
4
1 Name of the menu
2 Input mode
3 An item being selected (highlighted)
4 Screen resolution of input signal, and other data.
ADVANCED
SETUP
SETUP
3
3840x2160
RESET
PICTURE
PICTURE
DisplayPort
BRIGHT
3. Press [VOL+/
CONTRAST.
1
MONITOR
(Adjusting CONTRAST in the PICTURE menu)
1. Press [MENU/ENTER] button to display the menu
screen.
PICTURE
• The menu will differ depending on the input mode.
• The menu screen will close automatically if no operation is
performed for about 15 seconds.
] button to select
PICTURE
TIPS
• Items that cannot be selected appear in gray.
(e.g. Function not supported by the current input signal)
• The menu screen is on the left side of the screen in the
landscape orientation, and at the bottom of the screen in
the portrait orientation.
DisplayPort
BRIGHT
31
CONTRAST
BLACK LEVEL
30
30
TINT
COLORS
30
30
SHARPNESS
COLOR ADJUSTMENT
12
ADVANCED
RESET
3840x2160
V: 30Hz
H: 69.5kHz
4. Press brightness adjustment button (
the setting.
PICTURE
SETUP
MONITOR
PbyP
OTHERS
PICTURE
BACK···[RETURN]
/
) to adjust
DisplayPort
BRIGHT
31
CONTRAST
BLACK LEVEL
40
30
TINT
COLORS
30
30
SHARPNESS
COLOR ADJUSTMENT
12
ADVANCED
RESET
3840x2160
V: 30Hz
H: 69.5kHz
BACK···[RETURN]
For items that have
, press [MENU/ENTER] button and
then configure the settings.
5. Press [INPUT/RETURN] button to close the menu screen.
21
E
Menu Items
Menu item details
The menu will differ depending on the input mode.
nPICTURE
BRIGHT
Adjusts the backlight brightness.
CONTRAST
Adjusts the difference between the bright and dark portions of the image.
BLACK LEVEL
Adjusts the entire brightness of the video signals.
TINT
Adjusts the hue. Selecting + changes the color towards green, and selecting - changes it towards magenta.
COLORS
Adjusts the color intensity.
SHARPNESS
Adjusts the sharpness of the image. Some settings and images may cause vertical lines to appear in the center of the screen.
COLOR ADJUSTMENT
COLOR MODE
The color mode changes in the following order:
STD (Standard) → VIVID → sRGB → STD...
* sRGB applies to PC input only.
sRGB is international standard of color representation specified by IEC (International Electrotechnical Commission). Color
conversion is made in taking account of liquid crystal’s characteristics and represents color tone close to its original image.
WHITE BALANCE
THRU........... Displays the input signal level as is. (for PC input only)
PRESET....... Selects the color temperature using PRESET.
USER........... Used for adjusting R-/G-/B-CONTRAST and R-/G-/B-OFFSET respectively.
PRESET
Selects the color temperature when the WHITE BALANCE is set to PRESET.
The setting values are shown for reference. The color temperature of the screen varies over time.
This function is not intended to keep the color temperature constant.
USER
Adjusts each item when the WHITE BALANCE is set to USER.
R-CONTRAST...... Adjusts bright-toned red component.
G-CONTRAST..... Adjusts bright-toned green component.
B-CONTRAST...... Adjusts bright-toned blue component.
R-OFFSET........... Adjusts dark-toned red component.
G-OFFSET........... Adjusts dark-toned green component.
B-OFFSET........... Adjusts dark-toned blue component.
COPY TO USER
Copies the value of white set for PRESET to the USER setting.
Select “ON” and then press [MENU/ENTER] button.
(In the case other than white, color tone may differ from the PRESET.)
GAMMA
Selects the gamma.
C.M.S.-HUE (AV input)
Adjusts color tone with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).
C.M.S.-SATURATION (AV input)
Adjusts color vividness with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).
C.M.S.-VALUE (AV input)
Adjusts color brightness with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).
ADVANCED
RGB INPUT RANGE
Sets the RGB input signal range. To set automatically, select AUTO. Use AUTO normally.
If the RGB input signal range cannot be set appropriately even when using AUTO, set according to the image. When the
setting is different, images will be displayed with washed out blacks and compressed gradients.
RESET
Resets the values of the PICTURE menu items to the factory preset values.
Select “ON” and then press [MENU/ENTER] button.
E
22
Menu Items
nSETUP
LANGUAGE
Sets the display language for the menu screen.
INPUT SELECT
HDMI1/HDMI2
Select the input modes to be used for the PC/AV HDMI1 and HDMI2 input terminals.
HDMI DUAL
To use HDMI DUAL, select ON.
AUDIO SELECT
Selects the terminal used to input audio signals in each input mode.
When HDMI DUAL is used, the HDMI1 settings are applied.
AUDIO INPUT LEVEL
Selects the maximum audio input level of the audio input terminal.
TOUCH OUTPUT SETTING
Select the input terminal for which the touch operation mode will be enabled. (ALWAYS/DisplayPort/HDMI1/HDMI2/HDMI DUAL)
BAUD RATE
Selects the communication speed used for RS-232C communication.
DisplayPort STREAM
When using a screen resolution of 3840 x 2160 (50Hz/60Hz) in the DisplayPort input terminal, select MST (Multi-stream).
Images may not be displayed properly with some video card combinations.
nMONITOR
MONITOR
Select the installation direction of the monitor.
LANDSCAPE.............Landscape orientation
PORTRAIT................Portrait orientation
If the monitor is in a portrait orientation and a Windows PC is connected, set “Orientation” to “Portrait (Flipped)” in the “Screen
Resolution” settings.
If you are using a different operating system, refer to the manual for your operating system.
STANDBY MODE
When STANDARD is selected, startup time from standby mode is reduced. Note, however that, more power will be consumed
in standby mode.
When LOW POWER is selected, current consumption is reduced while the monitor is in standby mode. Note, however, that the
startup time from standby mode becomes longer.
If set to LOW POWER, certain RS-232C commands cannot be used in standby mode. (See page 29.)
OFF IF NO OPERATION
Determines whether or not to set the monitor go into standby mode when no monitor button or RS-232C command operations
are performed for over 4 hours.
TOUCH MODE AT STARTUP
Set the touch operation mode that will be in effect at startup.
RESET.......................“Finger/pen mode” at startup
NO RESET................Mode that was in effect when the power was last turned off.
MARK DISPLAY
TOUCH MARK DISPLAY
Set the display time of the touch mark. (5 S, ALWAYS) *
* When touch operation is disabled, the mark does not appear regardless of the setting.
CHANGE DISPLAY POSITION
Set the display position of the touch mark. (RIGHT, BOTTOM, LEFT, TOP)
23
E
Menu Items
nPbyP
PbyP MODE
Sets the display method.
OFF..........Displays one screen.
ON............Displays a main screen and a sub screen in a line.
* When using PbyP mode, set HDMI DUAL to OFF and DisplayPort STREAM to SST (Single Stream).
PbyP SOURCE
Select the input signal of the sub-screen in PbyP mode.
When the input mode is DisplayPort........ HDMI1 or HDMI2
When the input mode is HDMI1............... DisplayPort or HDMI2
When the input mode is HDMI2............... DisplayPort or HDMI1
nOTHERS
SCREEN MOTION
PATTERN
Residual images are reduced by moving the screen.
OFF..................SCREEN MOTION function is disabled.
PATTERN1
PATTERN2
PATTERN1.......A black screen spreads from the bottom of the screen and then
shrinks to the bottom of the screen. If the monitor is installed in the
portrait orientation, a black screen spreads from the left end of the
screen and then shrinks to the left end of the screen.
PATTERN2.......A black bar moves from the left end to the right end of the screen.
If the monitor is installed in the portrait orientation, a black bar
moves from the top to the bottom of the screen.
MOTION TIME 1
Specify a time period (operating interval) until SCREEN MOTION starts.
MOTION TIME 2
Specify a time period during which SCREEN MOTION operates (time period during which the screen will move).
POWER MANAGEMENT
POWER MANAGEMENT determines whether or not to switch modes from no signal to the input signal standby mode.
SIZE
Changes the screen size. (See page 17.)
4096 DISPLAY POSITION
Sets the position where the image is displayed (LEFT, CENTER,
LEFT
CENTER
RIGHT
or RIGHT) when a signal with 4096 horizontal dots is input.
When RIGHT or LEFT is set, a black band may appear in the
middle of the screen with some images.
This setting is only valid when the input is HDMI and the screen
size is Dot by Dot.
MUTE AUDIO
Temporarily mutes the sound. The sound is restored when OFF is selected.
* If using the monitor buttons, hold both [MENU/ENTER] button and [VOL-/
] button at the same time.
INFORMATION
Shows information about the monitor.
When HDMI DUAL is set to ON, the signal information of each terminal appears in HDMI1and HDMI2 fields.
When a button other than [VOL+/
/
]/[VOL-/
] button, brightness adjustment button (
) is pressed, or if no action is
taken for 15 seconds, the display disappears.
TIPS
• When WHITE BALANCE is set to THRU, BLACK LEVEL, CONTRAST, TINT, COLORS, RGB INPUT RANGE, GAMMA,
PRESET, USER and COPY TO USER cannot be set.
• If COLOR MODE is set to sRGB, the following items cannot be set.
WHITE BALANCE, PRESET, USER, COPY TO USER, and GAMMA
• When the COLOR MODE is set to VIVID, GAMMA can not be adjusted.
E
24
Menu Items
nDual screen display
Two screens can be displayed by selecting PbyP mode.
Set this function with “PbyP MODE” in the PbyP menu.
PbyP
Main
screen
Sub
screen
A main screen and a sub
screen are displayed in a
line.
* The currently selected input signal is displayed on the main screen.
* The following combinations are available for display: (Only when HDMI DUAL is set to OFF.)
DisplayPort - HDMI1 or HDMI2
HDMI1 - HDMI2
TIPS
• You might infringe on a copyright of the author which is protected by copyright law when you display the images of the
computer screen and television/VCR simultaneously for profit-making or to show the image to the public.
• The screen size for dual-screen display is the same as the screen size for single-screen display. The Dot by Dot screen is
displayed in NORMAL size.
• When dual-screen display is selected, the SCREEN MOTION function is disabled.
• When dual-screen display is selected, the INPUT SELECT options cannot be set.
nHDMI DUAL
• The HDMI1 and HDMI2 input screens can be displayed as a single screen. The HDMI1 input image will appear on the left
and the HDMI2 input image will appear on the right.
• The two HDMI1 and HDMI2 video signals must be output from the same device.
• The screen size can be set.
• The audio setting is the same as the AUDIO SELECT of HDMI1.
25
E
Initialization (Reset)/Functional Restriction Setting (FUNCTION)
You can return the settings to their factory-preset values and
restrict operations.
1. Hold down the [MENU/ENTER] button and [INPUT/
RETURN] button at the same time until “F” appears in
the screen, and then press the [MENU/ENTER] button
and [VOL-/
] button at the same time while “F”
appears.
▲
OK…[ENTER]
OFF
UNLOCKED
ON 1
ON
OFF
OFF
▲ ▲▲ ▲ ▲▲
ALL RESET
ADJUSTMENT LOCK
RS-232C
OSD DISPLAY
LED
TEMPERATURE ALERT
STATUS ALERT
▲▲ ▲ ▲ ▲ ▲
FUNCTION
END…[RETURN]
2. Select and set the items.
ALL RESET
Resets the settings to the factory default settings.
Select ALL RESET, and then press [MENU/ENTER]
button.
After initialization, turn the main power switch off and
then back on.
ALL RESET.......Resets all the settings to the factory
default settings.
CANCEL............Go back without resetting.
ADJUSTMENT LOCK
You can disable operations on the monitor buttons.
OFF....Enables operation.
ON 1...Disables all operations other than turning power
on/off and FUNCTION.
ON 2...Only the FUNCTION operation is enabled.
Disables all operations other than FUNCTION (not
even power on/off).
RS-232C
Specifies whether to allow control via RS-232C. (See
page 27.)
OSD DISPLAY
Shows/hides the menu, modes and messages.
The FUNCTION screen cannot be hidden.
ON 1............... Shows all menus, modes and messages.
ON 2............... Hides messages automatically displayed
by the display. Shows messages during
operation.
OFF................ Hides all menus, modes and messages.
LED
Specifies whether to light the power LED.
E
26
TEMPERATURE ALERT
Selects the notification method for an abnormal
temperature.
OFF............... Do not notify about an abnormal
temperature.
OSD & LED... When an abnormal temperature is
detected, the power LED flashes in red
and green alternately and the screen
displays a message: TEMPERATURE.
LED............... When an abnormal temperature is
detected, the power LED flashes in red
and green alternately.
STATUS ALERT
Selects the notification method for a hardware error.
OFF............... Do not notify about the error.
OSD & LED... When a hardware error is detected, the
power LED flashes in red and the screen
displays a message: STATUS [xxxx].
LED............... When a hardware error is detected, the
power LED flashes in red.
3. Press [INPUT/RETURN] button to return to the normal
screen.
TIPS
• When both abnormal temperature and hardware error are
detected, the hardware error notification overrides.
• If TEMPERATURE ALERT or STATUS ALERT is set to
OSD & LED, alert messages will appear even if the OSD
DISPLAY is set to ON 2 or OFF.
• If TEMPERATURE ALERT or STATUS ALERT is set to LED
or OSD & LED, the LED lights even if the LED function is
set to OFF.
Controlling the Monitor with a PC (RS-232C)
You can control this monitor from a PC via RS-232C (COM
port) on the PC.
Communication procedure
PC connection
When a command is sent from the PC to the monitor, the
monitor operates according to the received command and
sends a response message to the PC.
Connect the COM port on the PC (RS-232C connector) to the
CONTROL terminal (RS-232C input terminal) on the monitor
using the RS-232C conversion cable (supplied) and an RS232 straight cable (commercially available).
Bind the RS-232C conversion cable with the cable clamp.
nCommand format
Return code
C1
CONTROL terminal
(RS-232C
input terminal)
C2
C3
C4
P1
Command field
(4 prescribed
alphanumerical characters)
P2
P3
P4
Parameter field
(4 character string comprised of:
0-9, +, -, space, ?)
Example: VOLM0030
VOLM
30
PC
To COM port
RS-232 straight cable
(commercially available)
RS-232C conversion
cable (supplied)
* Be sure to input 4 characters for the parameter. Pad with
spaces (“ ”) if necessary.
(“
” is a return code (0DH, 0AH or 0DH))
Wrong : VOLM30
Right : VOLM
30
When inputting a negative value, specify a numerical value in
three digits.
Example: OFSR-127
Communication conditions
Set the RS-232C communication settings on the PC to match
the monitor’s communication settings as follows:
Baud rate
*
Stop bit
1 bit
Data length
8 bits
Flow control
None
Parity bit
None
* Set to the same baud rate as the BAUD RATE setting of
SETUP menu. (Initial setting: 38400 bps)
If a command has “R” listed for “Direction” in the
“RS-232C command table” on page 29, the current value can
be returned by using “?” as the parameter.
Example:
VOLM ? ? ? ?
←
From PC to monitor (How much
is current volume setting?).
30
←
From monitor to PC (Current
volume setting: 30).
27
E
Controlling the Monitor with a PC (RS-232C)
nResponse code format
When a command has been executed correctly
O
K
Return code
(0DH, 0AH)
A response is returned after a command is executed.
When a command has not been executed
E
R
R
Interval of 100 ms or more
• “ERR” is returned when there is no relevant command or
when the command cannot be used in the current state of
the monitor.
• If communication has not been established for reasons
such as a bad connection between the PC and monitor,
nothing is returned (not even ERR).
• “ERR” may be returned when a command cannot be
received correctly due to interference from the surrounding
environment.
Please ensure that the system or software retries the
command if this occurs.
If execution of the command is taking some time
A
I
T
Return code
(0DH, 0AH)
When the following commands are used, “WAIT” is returned.
In this case, a value will be returned if you wait a while. Do not
send any command during this period.
• Commands which return WAIT:
When one of the following commands is used:
RSET, INPS, WIDE, POWR, MWIN, MWIP, DPST
When control via RS-232C is locked (to prevent use)
using the operation lock function (See page 26.)
L
E
28
• After OK or ERR is returned, you must send the following
commands.
To set a timeout for the command response, specify 10
seconds or longer.
• Provide an interval of 100 ms or more between the
command response and the transmission of the next
command.
VOLM0020
OK
Return code
(0DH, 0AH)
TIPS
W
nCommunication interval
O
C
K
E
D
Return code
(0DH, 0AH)
INPS0001
WAIT
OK
TIPS
• When executing ALL RESET, set the timeout period to 30
seconds or longer.
Controlling the Monitor with a PC (RS-232C)
RS-232C command table
How to read the command table
Command:
Command field (See page 27.)
Direction:
W When the “Parameter” is set in the parameter field (See page 27.), the command functions as described
under “Control/Response Contents”.
R The returned value indicated under “Reply” can be obtained by setting “????” or “
?” in the
parameter field. (See page 27.)
Parameter:
Parameter field (See page 27.)
Reply:
Response (Returned value)
*:
“●” indicates a command which can be used in power standby mode regardless of the STANDBY MODE setting.
“○” indicates a command which cannot be used in power standby mode when STANDBY MODE is set to LOW POWER.
“–” indicates a command which cannot be used in power standby mode regardless of the STANDBY MODE setting.
Power control/Input mode selection
Function
POWER CONTROL
Command
Direction
POWR
W
Parameter
Reply
0
1
R
Control/Response contents
*
Switches to standby mode.
Returns from standby mode.
0 Standby mode
1 Normal mode
●
2 Input signal waiting mode
INPUT MODE SELECTION
INPS
W
0
Toggle change for input mode. Terminals not selected in INPUT SELECT cannot
be selected.
9
HDMI1 [AV]
“ERR” when PC is selected for HDMI1 of INPUT SELECT.
10
HDMI1 [PC]
“ERR” when AV is selected for HDMI1 of INPUT SELECT.
12
HDMI2 [AV]
“ERR” when PC is selected for HDMI2 of INPUT SELECT.
13
HDMI2 [PC]
“ERR” when AV is selected for HDMI2 of INPUT SELECT.
14
DisplayPort
15
R
●
HDMI DUAL
9 HDMI1 [AV]
10 HDMI1 [PC]
12 HDMI2 [AV]
13 HDMI2 [PC]
●
14 DisplayPort
15 HDMI DUAL
TOUCH ACTION MODES
TCMD
WR
0-2
0-2 0: Finger/pen mode, 1: Pen-only mode, 2: Finger-only mode
-
29
E
Controlling the Monitor with a PC (RS-232C)
PICTURE menu
Function
BRIGHT
Parameter
Reply
Command
Direction
VLMP
WR
0-31
CONTRAST
CONT
WR
0-60
0-60
BLACK LEVEL
BLVL
WR
0-60
0-60
TINT
WR
0-60
0-60
COLR
WR
0-60
0-60
SHARPNESS
SHRP
WR
0-24
0-24
COLOR
COLOR MODE
ADJUSTMENT
BMOD
WR
0
0 STD
2
2 VIVID
THRU
CTMP
WR
PRESET
USER
R-CONTRAST
3
3 sRGB (When the input mode is PC)
0
0 When the input mode is PC HDMI or DisplayPort.
1-18
99
0-256
0-256 “ERR” when CTMP is not set to 99.
G-CONTRAST CRTG
WR
0-256
0-256
B-CONTRAST
CRTB
WR
0-256
0-256
R-OFFSET
OFSR
WR
-127-127
-127-127
G-OFFSET
OFSG
WR
-127-127
-127-127
B-OFFSET
OFSB
WR
-127-127
-127-127
COPY TO USER
CPTU
W
GAMMA
GAMM
WR
CMHR
WR
C.M.S.-SATURATION
(during AV input)
0-2 0: 1.8, 1: 2.2, 2: 2.4 (during PC input)
0: LIGHT 2, 2: DARK (during AV input)
5-6
5-6 5: 2.0, 6: STD (during PC input)
5: LIGHT 1, 6: STD (during AV input)
-10-10
Y
CMHG
G
CMHC
C
CMHB
B
W
CMSR
WR
1
-10-10
Resets the hue.
-10-10 R
CMSY
Y
CMSG
G
CMSC
C
CMSB
B
C.M.S.-VALUE (during AV input) CMVR
WR
2
-10-10
Resets the saturation.
-10-10 R
Y
CMVG
G
CMVC
C
CMVB
B
CMVM
AV HDMI1 RGB INPUT RANGE AHDR
○
M
W
CMVY
CRST
-
M
CRST
CRST
○
-10-10 R
CMHY
CMSM
30
Copies a preset value to the user setting.
0-2
CMHM
RESET
99
WR
C.M.S.-HUE (during AV input)
ADVANCED
1-18 From 1: approximately 3,000K to 15: approximately 10,000K(500K steps)
16: approximately 5,600K, 17: approximately 9,300K,
18: approximately 3,200K
CRTR
0
*
○
TINT
COLORS
WHITE
BALANCE
E
Control/Response contents
0-31
M
W
WR
3
0-2
Resets the brightness.
0-2 0: AUTO, 1: FULL, 2: LIMITED
PC HDMI1 RGB INPUT RANGE PHDR
WR
0-2
0-2 0: AUTO, 1: FULL, 2: LIMITED
AV HDMI2 RGB INPUT RANGE AH2R
WR
0-2
0-2 0: AUTO, 1: FULL, 2: LIMITED
PC HDMI2 RGB INPUT RANGE PH2R
WR
0-2
0-2 0: AUTO, 1: FULL, 2: LIMITED
DisplayPort RGB INPUT RANGE
PDPR
WR
0-2
0-2 0: AUTO, 1: FULL, 2: LIMITED
ARST
W
2
○
-
Controlling the Monitor with a PC (RS-232C)
SETUP menu
Function
LANGUAGE
Command
Direction
LANG
WR
Parameter
Reply
14
1
AUDIO
SELECT
HDMI1
HDSL
WR
*
1 DEUTSCH
2
2 FRANÇAIS
3
3 ITALIANO
4
4 ESPAÑOL
5
5 РУССКИЙ
6
INPUT
SELECT
Control/Response contents
14 ENGLISH
○
6
0-1
0-1 0: PC HDMI, 1: AV HDMI
HDMI2
H2SL
WR
0-1
0-1 0: PC HDMI, 1: AV HDMI
HDMI DUAL
HDDU
WR
0-1
0-1 0: OFF, 1: ON
HDMI1 [PC]
ASHP
WR
0-1
0-1 0: HDMI, 1: STEREO MINI
HDMI1 [AV]
ASHA
WR
0-1
0-1 0: HDMI, 1: STEREO MINI
HDMI2 [PC]
AH2P
WR
0-1
0-1 0: HDMI, 1: STEREO MINI
HDMI2 [AV]
AH2A
WR
0-1
0-1 0: HDMI, 1: STEREO MINI
DisplayPort
1-2 1: DisplayPort, 2: STEREO MINI
ASDI
WR
1-2
TOUCH OUTPUT SETTING
USBC
WR
0-4
0-4 0: ALWAYS, 1:DisplayPort, 2:HDMI1, 3:HDMI2, 4:HDMI DUAL
AUDIO INPUT LEVEL
AIVP
WR
0-1
0-1 0: 1.0Vrms, 1: 0.5Vrms
BAUD RATE
BAUD
WR
0-2
0-2 0: 9600bps, 1: 19200bps, 2: 38400bps
DisplayPort STREAM
DPST
WR
0-1
0-1 0: SST, 1: MST
○
○
○
○
-
MONITOR menu
Parameter
Reply
Control/Response contents
Command
Direction
MONITOR
STDR
WR
0-1
0-1 0: LANDSCAPE, 1: PORTRAIT
STANDBY MODE
STBM
WR
0-1
0-1 0: STANDARD, 1: LOW POWER
OFF IF NO OPERATION
ATOF
WR
0-1
0-1 0: OFF, 1: ON
TOUCH MODE AT STARTUP
POTM
WR
0-1
0-1 0: RESET, 1: NO RESET
MARK DISPLAY
TOUCH MARK
DISPLAY
TMDT
WR
0-1
0-1 0: ALWAYS, 1: 5 S
CHANGE DISPLAY
POSITION
TPOS
WR
0-3
0-3 0: RIGHT, 1: BOTTOM, 2: LEFT, 3: TOP
Function
*
○
○
○
-
PbyP menu
Function
Parameter
Reply
Command
Direction
PbyP MODE
MWIN
WR
0,2
PbyP SOURCE
MWIP
WR
9
9 HDMI1 [AV]
10
10 HDMI1 [PC]
12
12 HDMI2 [AV]
13
13 HDMI2 [PC]
14
14 DisplayPort
Control/Response contents
0,2 0: OFF, 2: ON
“ERR” when HDMI DUAL is ON.
*
○
○
OTHERS menu
Function
SCREEN
MOTION
PATTERN
Command
Direction
SCSV
WR
Parameter
0,2,3
Reply
Control/Response contents
0,2,3 0: OFF, 2: PATTERN1, 3: PATTERN2
MOTION TIME 1
MTIM
WR
0-20
0-20
MOTION TIME 2
MINT
WR
5-20
5-20 Per second
POWER MANAGEMENT (PC)
PMNG
WR
0-1
0-1 0: OFF, 1: ON
POWER MANAGEMENT (AV)
PMAV
WR
0-1
0-1 0: OFF, 1: ON
SIZE (PC)
WIDE
WR
1-3
1-3 1: WIDE, 2: NORMAL, 3: Dot by Dot
SIZE (AV)
WIDE
WR
1, 4-5
1, 4-5 1: WIDE, 4: NORMAL, 5: Dot by Dot
4096 DISPLAY POSITION
4KDP
WR
0-2
MUTE AUDIO
MUTE
WR
0-1
INFORMATION MODEL
INF1
R
Value
SRNO
R
Value
SERIAL NO
0-2 0: LEFT, 1: CENTER, 2: RIGHT
0-1 0: OFF, 1: ON
*
○
○
○
○
○
○
●
31
E
Controlling the Monitor with a PC (RS-232C)
Initialization/Functional Restriction Setting (FUNCTION) menu
Command
Direction
ALL RESET
Function
RSET
W
Parameter
Reply
Control/Response contents
ADJUSTMENT LOCK
ALCK
WR
0-2
0-2 0: OFF, 1:ON 1, 2:ON 2
OSD DISPLAY
LOSD
WR
0-2
0-2 0: ON 1, 1: OFF, 2: ON 2
LED
OFLD
WR
0-1
0-1 0: ON, 1: OFF
TEMPERATURE ALERT
TALT
WR
0-2
0-2 0: OFF, 1: OSD & LED, 2: LED
STATUS ALERT
SALT
WR
0-2
0-2 0: OFF, 1: OSD & LED, 2: LED
0
*
○
○
○
○
○
Others
Command
Direction
VOLUME
Function
VOLM
WR
Parameter
0-31
Reply
0-31
Control/Response contents
BRIGHT
VLMP
WR
0-31
0-31
TEMPERATURE SENSOR
DSTA
R
0 Internal temperature normal
*
○
○
1 Internal temperature abnormal has occurred and the monitor is in
standby mode
2 Internal temperature abnormal occurred (To delete the information of
temperature abnormal, turn off the main power.)
●
3 Internal temperature abnormal has occurred and backlight brightness is
dimmed
4 Temperature sensor abnormal
TEMPERATURE ACQUISITION
ERRT
R
CAUSE OF LAST STANDBY MODE
STCA
W
R
Value Returns the temperature of the temperature sensor.
Indicates a temperature sensor abnormality when “126” is returned.
0
○
Initialization
0 No detectable error has occurred
1 Standby mode by POWER button
2 Main power off by the main power switch
3 Standby mode by RS-232C
4 Input signal waiting mode by No Signal
6 Standby mode by abnormal temperature
20 Standby mode by OFF IF NO OPERATION setting
E
32
●
Troubleshooting
If you are experiencing any problem with your display, before
calling for service, please review the following troubleshooting
tips.
There is no picture or sound.
• Are the AC adapter and power cord properly connected?
(See page 13.)
• Is the main power switch off? (See page 15.)
• Is the monitor in standby mode (power lamp is off)? (See
page 15.)
• Make sure correct input mode is selected. (See page 16.)
• If any external equipment is connected, make sure the
equipment is operating (playing back).
Sound from left and right speakers is reversed.
Sound is heard from only one side.
• Are audio cables connected properly? (See page 12.)
There is a picture but no sound.
• Is the sound muted?
• Make sure the volume is not set to minimum.
• Are audio cables connected properly?
• Is the setting of AUDIO SELECT on the SETUP menu
correct? (See page 23.)
• Is the headphone (etc.) cable connected to the headphone
terminal?
The sound crackles.
• Turn down the volume.
With some input devices, the sound may crackle at high
volume.
Unstable video.
• The signal may be incompatible.
The video from the PC/AV HDMI input terminal does not
appear properly.
• Is the HDMI or HDMI DUAL setting correct in INPUT
SELECT on the SETUP menu? (See page 23.)
• Is the HDMI cable HDMI standard compliant? The monitor
will not work with cables that are not standard compliant.
• Is the input signal compatible with this monitor? (See pages
37 to 38.)
The video from DisplayPort input terminal does not
appear properly.
• Is the cable a certified DisplayPort cable? Use the supplied
cable. The monitor will not work unless a standards-compliant
cable is used.
• Is the input signal compatible with this monitor? (See page
37.)
The video does not appear properly even after the
DisplayPort STREAM setting is changed.
• Try restarting the monitor and computer.
• Is the video card MST (Multi Stream) compatible? If not, set
to SST (Single Stream).
The touch panel does not respond.
• Is the USB cable connected properly? (See page 12.)
• The touch panel may not work properly if the contact area
is too large. (e.g. if the screen is touched with the palm of
your hand.) Try to only contact the touch screen with the
supplied pen or your fingertip.
• Is the monitor in pen-only mode? Touch action is disabled
in pen-only mode. (See page 18.)
• Is the monitor in finger-only mode? You cannot touch the
screen with the touch pen when in finger-only mode. (See
page 18.)
• When there is no signal input to the LCD monitor, actions
on the touch panel are not possible. Please operate the PC
using the mouse and keyboard.
• If you are using Windows XP or Windows Vista, did
you install the touch panel driver? (Touch Panel Driver
Operation Manual)
• Is TOUCH OUTPUT SETTING set correctly in the SETUP
menu? (See page 23.)
• Touch operation is not possible when screen motion
is enabled or when PbyP mode is set to ON. Set each
function to OFF.
• When the computer is in sleep mode, wake-up by touch
operation may not be possible.
To enable wake-up by touch operation, settings must be
configured on the computer. For information on configuring
the settings, consult your dealer.
The response of the touch screen is slow.
Some parts of the screen do not respond.
• When starting your computer or connecting the USB cable,
do not touch the touch panel.
• When starting the LCD monitor, do not touch the screen.
If the screen is touched, the monitor may not function
correctly. In this situation, turn off the LCD monitor power,
wait 5 seconds or longer, and then turn the power on again.
• While the touch mode icon is displayed, only touch actions
for the icon can be performed. To perform other actions,
first close the icon display.
• There may be no response if the supplied touch pen is
gripped in such a way that the tip is located near your palm.
In this situation, grip the pen so the tip is further extended
from the base of your hand.
Control buttons do not work.
There is no picture.
• Load noises from outside may be interfering with normal
operation. Turn off the power and turn it on after waiting at
least 5 seconds, and then check the operation.
• When you display the screen or clear the screen, the left
and right screen display timing may be slightly off; however,
this is not a problem.
Power LED flashes red.
“STATUS [xxxx]” appears in the corner of the screen.
• Hardware has a problem. Turn off the monitor and request
repair from your SHARP dealer.
(When STATUS ALERT is set to OSD & LED. This varies
depending on the setting.)
33
E
Troubleshooting
When “AUTO DIMMING” is displayed.
• When the internal temperature of the monitor rises excessively,
the brightness of the backlight automatically decreases in
order to prevent a further temperature rise.
/
)
If you attempt to use brightness adjustment button (
to adjust the brightness while the monitor is in this state, “AUTO
DIMMING” is displayed and you cannot change the brightness.
• Remove the cause of the excessive temperature rise.
The monitor makes a cracking sound.
• You may occasionally hear a cracking sound from the
monitor. This happens when the cabinet slightly expands
and contracts according to change in temperature. This
does not affect the monitor’s performance.
The Power LED is flashing in red and green alternately.
When “TEMPERATURE” is displayed in the corner of the
screen.
• When the internal temperature of the monitor rises
excessively, the brightness of the backlight decreases
automatically in order to prevent high-temperaturerelated problems. When this occurs, “TEMPERATURE” is
displayed on the screen and the Power LED flashes red
and green alternately. (When TEMPERATURE ALERT is
set to OSD & LED. This varies depending on the setting.)
• If the internal temperature rises further, the monitor
automatically enters standby mode. (The Power LED
continues flashing red and green alternately.)
• Remove the cause of the excessive temperature rise.
- If the monitor enters standby mode due to a rise in
temperature, to return to normal display, turn the power
switch off and then back on again. The monitor, however,
will enter standby mode again if the cause of the
temperature rise is not eliminated. (See page 15.)
- Check whether the monitor is placed at a location where
a quick rise in temperature is likely. Internal temperature
rises quickly if the vents on the monitor are blocked.
- Internal temperature rises quickly if dust accumulates
inside the monitor or around the vents. Remove dust if
possible. Ask SHARP dealer about removing internal dust.
A residual image has occurred.
After the image has changed, the previous image is faintly
visible.
• Displaying the same image for an extended time may
cause a residual image.
• To improve a residual image, keep the power off. With the
power off state, the residual image will gradually disappear
as time passes. If there is no improvement, display a full
white screen or an animated image.
E
34
Specifications
nProduct Specifications
Model
LCD component
Max. resolution
(pixels)
Max. colors
Pixel pitch
Viewing angle
Screen active area
inch (mm)
Response speed
Plug and play
Power management
Input terminals
PC/AV
PC
Audio
Serial (RS-232C)
Output terminals
Audio
Speaker output
Touch Panel
Touch screen system
USB (for touch panel
communication)
Maximum touch points
Power requirement
Operating temperature
Operating humidity
Power consumption
(input signal waiting mode *1 / standby mode)
Dimensions (excluding protrusions)
inch (mm)
Weight PN-K322B
32" Class [31-35/64 inch (80.1cm) diagonal] TFT LCD
3840 x 2160
Approx. 1.07 billion colors
0.182 mm (H) × 0.182 mm (V)
176° right/left/up/down (contrast ratio ≥ 10)
27-31/64 x 15-15/32 (697.9 x 392.6)
8 ms (Gray to Gray, avg.)
VESA DDC2B
VESA DisplayPort
HDMI x 2
DisplayPort x 1
3.5 mm mini stereo jack x 1
3.5 mm mini jack x 1
3.5 mm mini stereo jack x 1
2W+2W
Capacitive
x1, USB (mini-B)
10 points
AC 100 V - 240 V, 50/60 Hz (when using the supplied AC adapter)
41°F to 95°F (5°C to 35°C)
20% to 80% (no condensation)
97 W *2 (7.2 W / 7.2 W) (when using the supplied AC adapter)
Monitor only
Approx. 29-17/32(W) x 1-27/64(D) x 17-3/8(H) (750 x 36 x 441)
Monitor on supplied stand
• Monitor screen angle 90° (from horizontal)
Approx. 29-17/32(W) x 15-23/64(D) x 19-27/64(H) (750 x 390 x 493)
• Monitor screen angle 25° (from horizontal)
Approx. 29-17/32(W) x 22-41/64(D) x 8-5/32(H) (750 x 575 x 207)
lbs. (kg) Approx. 19.9 (9.0) (monitor only)
Approx. 35.3 (16.0) (monitor on supplied stand)
*1 When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 1.3 W
*2 When using the monitor in DC19.5 V : 91 W
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement
without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
35
E
Specifications
nDimensional Drawings
Note that the values shown are approximate values.
• Monitor screen angle 90° (from horizontal)
10-33/64 [267]
Unit: inch [mm]
1-27/64
[36]
3-15/16 3-15/16
[100] [100]
29-17/32 [750]
3-15/16 3-15/16
[100]
[100]
19-27/64 [493]
Opening height (15-9/16 [395])
17-3/8 [441]
Opening width (27-9/16 [700])
15-23/64 [390]
• Monitor screen angle 25° (from horizontal)
8-5/32 [207]
Unit: inch [mm]
22-41/64 [575]
When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method.
SHARP recommends using M6 screws and tighten the screws.
Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in
serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch
(8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times
or more the weight of the monitor.
E
36
Specifications
nCompatible signal timing (PC)
Screen resolution
VESA
640×480
800×600
848×480
1024×768
1152×864
1280×768
1280×800
1280×960
1280×1024
1360×768
1400×1050
1600×1200
1680×1050
1920×1200
3840×2160
Wide
US TEXT
*1
*2
*3
*4
*5
*6
4096×2160*2
1280×720
1920×1080
720×400
Vsync
DisplayPort
HDMI1
or HDMI2
60Hz
72Hz
75Hz
56Hz
60Hz
72Hz
75Hz
60Hz
60Hz
70Hz
75Hz
75Hz
60Hz
75Hz
60Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
60Hz
60Hz
24Hz
25Hz
30Hz
50Hz
60Hz
24Hz
60Hz
60Hz
70Hz
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes*3*6
Yes*3*6
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
HDMI DUAL*1
Yes*4
Yes*4
Yes*4
Yes*4
Yes*5
-
A single screen is created from simultaneous input of two systems using HDMI1 and HDMI2.
Displays a reduced image, except in Dot by Dot. In Dot by Dot, the image will be cut down to panel size then displayed.
Displays using multi-streaming.
The two HDMI input terminals both have 1920 x 2160 signals.
The two HDMI input terminals both have 2048 x 2160 signals.
The signals for the left and right screens are both 1920 x 2160 signals.
* All are compliant only with non-interlaced.
* Depending on the connected PC, images may not be displayed properly even if the compatible signal described above is input.
37
E
Specifications
nCompatible signal timing (AV)
Screen resolution
1920 × 1080p
1920 × 1080i
1280 × 720p
720 × 576p
720 × 480p
640 × 480p(VGA)
720(1440) × 576i
720(1440) × 480i
Frequency
24Hz
50Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
59.94Hz
60Hz
50Hz
59.94Hz
60Hz
HDMI
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
nPower management
This monitor conforms to VESA DisplayPort power management.
nDDC (plug and play)
The monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters
is exchanged between the two. This function can be used if the computer supports DDC and it has been configured to detect
plug-and-play monitors.
There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.
E
38
Specifications
nDisplayPort input
(DisplayPort 20 pin)
No.
Function
terminal pins
nPC/AV
(HDMI
No.
Function
No.
TM
HDMI input terminal pins
Connector)
Function
No.
Function
1
MainLane 3-
11
Gnd
1
TMDS data 2+
11
TMDS clock shield
2
Gnd
12
MainLane 0+
2
TMDS data 2 shield
12
TMDS clock-
3
MainLane 3+
13
Gnd
3
TMDS data 2-
13
CEC
4
MainLane 2-
14
Gnd
4
TMDS data 1+
14
N.C.
5
Gnd
15
Aux+
5
TMDS data 1 shield
15
SCL
6
MainLane 2+
16
Gnd
6
TMDS data 1-
16
SDA
7
MainLane 1-
17
Aux-
7
TMDS data 0+
17
DDC/CEC GND
8
Gnd
18
Hot-plug detection
8
TMDS data 0 shield
18
+5V
9
MainLane 1+
19
Gnd
9
TMDS data 0-
19
Hot-plug detection
10
MainLane 0-
20
3.3V
10
TMDS clock+
39
E
Mounting Precautions
(For SHARP dealers and service engineers)
• When installing, removing or moving the monitor, ensure
that this is carried out by at least 2 people.
• Be sure to use a wall-mount bracket designed or
designated for mounting the monitor.
• This monitor is designed to be installed on a concrete wall
or pillar. Reinforced work might be necessary for some
materials such as plaster / thin plastic board / wood before
starting installation.
This monitor and bracket must be installed on a wall which
can endure at least 4 times or more the weight of the
monitor. Install by the most suitable method for the material
and the structure.
• To attach a VESA-compliant mounting bracket, use M6
screws that are 5/16 inch (8 mm) to 3/8 inch (10 mm)
longer than the thickness of the mounting bracket.
• Do not use an impact driver.
• When moving the monitor, be sure to hold it with the unit
bottom and the side of unit. Do not hold the LCD panel or
corners. This may cause product damage, failure, or injury.
• Do not use any screw holes other than VESA holes for
installation.
nRemoving the stand
Secure to wall or post
1. Attach a commercially available eye bolt (a bolt shaped to
allow attachment of a string or cord) to the wall or post.
Verify that the eye bolt is attached firmly and does not come out.
• Top of monitor
Commercially available
eye bolt
(bolt shaped to allow
attachment of a string
or cord)
2. Attach the supplied anti-toppling clamps (x2) to the stand
pedestal with the screws (M4 x 10) (x2).
• Back of monitor
Caution
• The stand is only for use with the monitor.
Do not use with any other devices.
• The stand is heavy. Take care not to let it fall.
1. S
pread a thick, soft cloth (blanket, etc.) that will prevent
damage to the LCD panel on a stable flat surface where
the entire monitor can be placed, and place the monitor
with the LCD panel face down on the cloth.
2. R
emove the screws(x4) that fasten the stand, and
remove the stand.
3. Run a commercially available cord of sufficient strength
through the anti-toppling clamps and the eye of an eye
bolt attached to the wall or a post to secure the monitor.
• Top of monitor
Commercially
available cord
• Back of monitor
nToppling prevention
Caution
• To reduce the risk of injury and damage caused by the
product toppling or falling in an earthquake or similar
situation, take measures to prevent toppling and falling.
• If the wall or platform on which the monitor is installed is
not sufficiently strong, the effectiveness of the toppling/
falling prevention measures will be severely compromised.
Reinforce the wall or platform as needed.
The toppling/falling prevention measures are intended to
reduce the risk of injury and damage in an earthquake,
however, the effectiveness of the measures is not
guaranteed in all earthquakes.
• Before implementing the toppling prevention measures,
complete all connections.
E
40
PN-K322B Mu EN13F(1)