AG Neovo TM-23 touch screen monitor User manual

Add to my manuals
26 Pages

advertisement

AG Neovo TM-23 touch screen monitor User manual | Manualzz
TM-22, TM-23 & TM-27 Multi-touch Display
User Manual
TABLE OF CONTENTS
SAFETY PRECAUTIONS..................................................................3
FOR YOUR SAFETY....................................................................3
SPECIAL NOTES ON LCD MONITOR.........................................5
BEFORE YOU OPERATE THE MONITOR.......................................6
FEATURES...................................................................................6
CHECKING THE CONTENTS OF THE PACKAGE......................6
INSTALLATION INSTRUCTIONS.................................................6
ADJUSTING THE VIEWING ANGLE............................................6
CONNECTING CABLES..............................................................7
GENERAL INSTRUCTIONS.........................................................9
EXTERNAL CONTROLS..............................................................9
OPERATING INSTRUCTIONS..........................................................9
FRONT PANEL CONTROL.........................................................10
HOW TO ADJUST A SETTING...................................................11
ADJUSTING THE PICTURE.......................................................12
PLUG AND PLAY........................................................................15
TECHNICAL SUPPORT (FAQ).......................................................16
ERROR MESSAGE & POSSIBLE SOLUTION..........................17
APPENDIX......................................................................................18
SPECIFICATIONS......................................................................18
FACTORY PRESET TIMING TABLE..........................................20
CONNECTOR PIN ASSIGNMENT.............................................21
PRODUCT DIMENSIONS..........................................................24
2
FOR YOUR SAFETY
Before operating the monitor, please read this manual thoroughly. This manual
should be retained for future reference.
SAFETY PRECAUTIONS
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
This device complies with Part 15 of the FCC rules.Operation is subject to the
following two conditions:(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE:
1. The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to
comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modification to this equipment. It is the responsibilities of the user
to correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture.
Dangerously high voltages are present inside the monitor. Do not open the cabinet.
Refer servicing to qualified personnel only.
3
FOR YOUR SAFETY
PRECAUTIONS
• Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink,
laundry tub, swimming pool or in a wet basement.
• Do not place the monitor on an unstable cart, stand, or table. If the monitor falls,
it can injure a person and cause serious damage to the appliance. Use only
a cart or stand recommended by the manufacturer or sold with the monitor. If
you mount the monitor on a wall or shelf, use a mounting kit approved by the
manufacturer and follow the kit instructions.
• Slots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it from
overheating, be sure these openings are not blocked or covered. Do not place
the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor
near or over a radiator or heat register. Do not place the monitor in a bookcase
or cabinet unless proper ventilation is provided.
• The monitor should be operated only from the type of power source indicated on
the label. If you are not sure of the type of power supplied to your home, consult
your dealer or local power company.
• The monitor is equipped with a three-pronged grounded plug, a plug with a
third (grounding) pin. This plug will fit only into a grounded power outlet as a
safety feature. If your outlet does not accommodate the three-wire plug, have
an electrician install the correct outlet, or ground the appliance safely. Do not
defeat the safety purpose of the grounded plug.
• Unplug the unit during a lightening storm or when it will not be used for long
period of time. This will protect the monitor from damage due to power surges.
• Do not overload power strips and extension cords. Overloading can result in fire
or electric shock.
• Never push any object into the slot on the monitor cabinet. It could short circuit
parts causing a fire or electric shock. Never spill liquids on the monitor.
• Do not attempt to service the monitor by yourself; opening or removing covers
can expose you to dangerous voltages and other hazards. Please refer all
servicing to qualified service personnel.
• To ensure satisfactory operation, use the monitor only with UL listed computers
which have appropriate configured receptacles marked between 100 - 240V AC,
Min. 5A.
• The wall socket shall be installed near the equipment and shall be easily
accessible.
4
FOR YOUR SAFETY
WEEE DECLARATION
Disposal of Waste Equipment by Users in Private Household in the European
Union.
This symbol on the product or on its packaging indicates that this product
must not be disposed of with your other household waste.Instead, it is
your responsibility to dispose of your waste equipment by handing it over
to a designated collection point for the recycling of waste electrical and
electronic equipment.The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources
and ensure that it is recycled in a manner that protects human health and
the environment. For more information about where you can drop off your
waste equipment for recycling, please contact your local city office, your
household waste disposal service or the shop where you purchased the
product.
SPECIAL NOTES ON LCD MONITOR
The following symptoms are normal with LCD monitor and do not indicate a
problem.
NOTES
• Due to the nature of the fluorescent light, the screen may flicker during initial
use.
• Turn off the Power Switch and then turn it on again to make sure the flicker
disappears.
• You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
• The LCD screen has effective pixels of 99.99% or more. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the time.
• Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours.
In this case, the screen is recovered slowly by changing the image or turning off
the Power Switch for hours.
• To declare the product is the Information Technical Equipment intended primarily
for use in the domestic environment.
• The monitor is for computer use and not marketed and intended for displaying
any television broadcast signals.
5
BEFORE YOU OPERATE THE MONITOR
FEATURES
• 54.69cm(21.53 inches) TFT Color LCD Monitor
58.42cm(23 inches) TFT Color LCD Monitor
68.6cm(27 inches) TFT Color LCD Monitor
• Crisp, Clear Display for Windows
• Recommended Resolutions: 1920x1080@60Hz
• Ergonomic Design
• Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
1. LCD Monitor
2. Owner’s Manual (including CD-ROM & Warranty Card)
3. Power Cord
4. 15-pin D-Sub Cable
5. Audio Cable
6. USB Cable
INSTALLATION INSTRUCTIONS
For optimal viewing it is recommended to look at the full face of the monitor. You
are able to adjust the monitor’s height (H):
120mm-385mm(TM-22)
129mm-409mm(TM-23)
145mm-454mm(TM-27)
Figure 1 Installation Instruction
ADJUSTING THE VIEWING ANGLE
Hold the stand so that the monitor does not topple when you
change the monitor’s angle.You are able to adjust the
monitor’s angle from -5° to 90°.
• Put the monitor on a flat surface.
• Hold the panel so that the monitor does not topple.
• We recommend that you adjust the stand to its lowest
position when using the monitor in the 90 degree upward
tilt position.
Figure 2 Adjusting the
Viewing Angle
6
BEFORE YOU OPERATE THE MONITOR
Power Source:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an External universal power supply that allows operation
in either 100/120V AC or 220/240V AC voltage area (No user adjustment is
required.)
3. Connect the AC-power cord into your LCD monitor’s AC-power-input. The AC
power cord may be connected to either a wall power outlet or the power outlet
socket on your PC, depending on the type of power cord supplied with your
LCD monitor.
CONNECTING CABLES
SIGNAL CABLE
Connecting the Signal Cable: Plug the Signal Cable one end to LCD monitor’s
“DSUB” socket, the other end to the computer’s VGA port and tighten the two
screws on the cable connector.
Connecting the DP Cable: Plug the DP Cable one end to the output port of DP
video equipment, the other end to LCD monitor’s “ ” socket.
Connecting the HDMI Cable: Plug the HDMI Cable one end to the output port of
HDMI video equipment, the other end to LCD monitor’s “HDMI” socket.
Connecting the Power Cord: Connect the AC-power cord into your LCD
monitor’s “AC-IN”. The AC-power cord may be connected to either a wall power
outlet or the power outlet socket on your PC, depending on the type of power cord
supplied with your LCD monitor.
Connecting the Audio Cable: Connect the audio cable between the monitor’s
“AUDIO-IN” socket and the PC’s audio output (green port).
Connecting the USB Cable: Plug the USB Cable one end to LCD Monitor’s USB
upstream, the other end to the computer’s USB port. (Note: Touch or Webcam
function can work only when this cable is connected.)
7
BEFORE YOU OPERATE THE MONITOR
G
AV
C
F
A
E
D
B
Figure 3 Connecting Cables
Label
A
B
C
D
E
F
G
Cable Type
AC-IN socket
DP input socket
HDMI input socket
D-SUB input socket
AUDIO-IN socket
USB upstream
USB downstream
8
PC
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons are
located at front panel of the monitor (See Figure 4). By changing these settings, the
picture can be adjusted to your personal preferences.
• The power cord should be connected.
• Connect the video cable from the monitor to the video card.
• Press the power button to turn on the monitor position. The power indicator will
light up.
WebCam
1
2
3
4
5
6
TM-22/TM-23:without WebCam
TM-27: with WebCam
Figure 4 External Control Button
EXTERNAL CONTROLS
No.
1
2
3
4
5
6
Description
UP / Volume+
DOWN/ ECO hotkey
AUTO / SOURCE / EXIT
MENU / ENTER
Power Button
Power Indicator
9
OPERATING INSTRUCTIONS
FRONT PANEL CONTROL
•
/ Power Button:
Press this button to turn the monitor ON or OFF, and display the monitor’s state.
• Power Indicator:
Blue — Power On mode.
Orange — Standby mode.
• MENU / ENTER:
Activate OSD menu when OSD is OFF or activate/de-activate adjustment
function when OSD is ON or Exit OSD menu when in Volume Adjust OSD
status.
• DOWN / ECO hotkey:
Activates ECO control when the OSD is off or adjust a function when function is
activated.
• UP / Volume+:
Activates the volume control when the OSD is off or adjust a function when
function is activated.
• Auto/ Source / Exit:
1. When OSD menu is in active status, this button will act as EXIT-KEY (EXIT
OSD menu).
2. When OSD menu is in off status, press this button to select input Source:
DSub/DP/HDMI.
3. When OSD menu is in off status, press this button for 2 seconds to activate
the Auto Adjustment function. The Auto Adjustment function is used to set the
HPos, VPos, Clock and Phase.
OSD Lock Function: To lock the OSD, press and hold the MENU button while
the monitor is off and then press power button to turn the monitor on. To unlock
the OSD - press and hold the MENU button while the monitor is off and then press
power button to turn the monitor on.
NOTES
• Do not install the monitor in a location near heat sources such as radiators or air
ducts, or in a place subject to direct sunlight, or excessive dust or mechanical
vibration or shock.
• Save the original shipping carton and packing materials, as they will come in
handy if you ever have to ship your monitor.
• For maximum protection, repackage your monitor as it was originally packed at
the factory.
• To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn
stains may be removed with a cloth lightly dampened with a mild detergent
solution. Never use strong solvents such as thinner, benzene, or abrasive
cleaners, since these will damage the cabinet. As a safety precaution, always
unplug the monitor before cleaning it.
• Do not scratch the screen with hard things, it may cause permanent damage.
• Don’t leak liquid into monitor which will result in the damage of component.
10
OPERATING INSTRUCTIONS
HOW TO ADJUST A SETTING
1. Press the MENU-button to activate the OSD window.
2. Press UP or DOWN to navigate through the functions. Once the desired function
ishighlighted, press the MENU-button to activate it. If the function selected
has a sub-menu, press UP or DOWN again to navigate through the submenu
functions. Once the desired function is highlighted, press MENU-button to
activate it.
3. Press UP or DOWN to change the settings of the selected function.
4. To exit and save, select the exit function. If you want to adjust any other function,
repeat steps 2-3.
Figure 5 OSD Message
11
OPERATING INSTRUCTIONS
ADJUSTING THE PICTURE
The descriptions for function control LEDS.
Main Menu
Item
Main
Menu
Icon
Sub Menu
Item
Sub
Menu
Contrast
Description
Contrast from Digital-register
Brightness
Backlight Adjustment
Standard Standard Mode
Text
Luminance
Eco
DCR
Game
Game Mode
Movie
Movie Mode
Sports
Sports Mode
Off
Disable dynamic contrast ratio.
On
Enable dynamic contrast ratio.
Clock
Adjust Picture Clock to reduce
Vertical-Line noise.
Phase
Adjust Picture Phase to reduce
Horizontal-Line noise.
H.Position
Adjust the horizontal position of
the picture.
V.Position
Adjust the vertical position of
the picture.
Image Ratio
Wide/ 4:3
Warm
Recall Warm Color Temperature
from EEPROM.
Normal
Recall Normal Color
Temperature from EEPROM.
Cool
Recall Cool Color Temperature
from EEPROM.
sRGB
Recall SRGB Color
Temperature from EEPROM.
Image
Setup
Color
Temp.
Text Mode
Internet Internet Mode
User
User-B
Blue Gain from Digital-register
User-G
Green Gain from Digital-register
User-R
Red Gain from Digital-register
12
OPERATING INSTRUCTIONS
Main Menu
Item
Main
Menu
Icon
Sub Menu
Item
Sub
Menu
Description
on or off
Disable or Enable Full Enhance
Mode.
on or off
Disable or Enable Nature Skin
Mode.
on or off
Disable or Enable Green Field
Mode.
Sky-blue
on or off
Disable or Enable Sky-blue
Mode.
AutoDetect
on or off
Disable or Enable AutoDetect
Mode.
Demo
on or off Disable or Enable Demo.
Full
Enhance
Nature
Color
Boost
Picture
Boost
Skin
Green
Field
Frame Size
Adjust Frame Size.
Brightness
Adjust Frame Brightness.
Contrast
Adjust Frame Contrast.
H.Position
Adjust the horizontal position of
Frame.
V.Position
Adjust the vertical position of
Frame.
Bright Frame
on or off Disable or Enable Bright Frame.
Adjust the horizontal position of
OSD.
Adjust the vertical position of
H.Position
OSD Setup
V.Position
Timeout
OSD.
Adjust the OSD Timeout.
Language
Select the OSD language.
13
OPERATING INSTRUCTIONS
Main Menu
Item
Main
Menu
Icon
Sub Menu
Item
Sub
Menu
D-Sub
Input Select
DP
HDMI
Extra
Description
Select analog input source.
Select DP input source.
Select HDMI input source.
DDC/CI
Turn ON/OFF DDC/CI Support.
Reset
Reset the menu to default.
Information
Show the information of the
main image and sub-image
source.
14
OPERATING INSTRUCTIONS
PLUG AND PLAY
Plug & Play DDC1/2B Feature
This monitor is equipped with VESA DDC1/2B capabilities according to the VESA
DDC STANDARD. It allows the monitor to inform the host system of its identity
and, depending on the level of DDC used, communicate additional information
about its display capabilities. The communication channel is defined in two levels,
DDC1 and DDC2B.
The DDC1 is a unidirectional data channel from the display to the host that
continuously transmits EDID information. The DDC2B is a bidirectional data
channel based on the I²C protocol. The host can request EDID information over the
DDC2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS
NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE
PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video Electronics
Standards Association (VESA) and The Swedish Confederation Employees
(NUTEK). This feature is designed to conserve electrical energy by reducing power
consumption when there is no video-input signal present. When there is no video
input signal this monitor, following a time-out period, will automatically switch to
an OFF mode. This reduces the monitor’s internal power supply consumption.
After the video input signal is restored, full power is restored and the display is
automatically redrawn. The appearance is similar to a “Screen Saver” feature
except the display is completely off. The display is restored by pressing a key on
the keyboard, or clicking the mouse.
15
TECHNICAL SUPPORT (FAQ)
Problem & Question
Power LED is not on.
Possible Solution
• Check if the Power Switch is in the ON position.
• Power Cord should be connected.
No Plug & Play
•
•
•
•
Picture is fuzzy.
Check if the PC system is Plug & Play compatible.
Check if the Video Card is Plug & Play compatible.
Check if the D-15 plug pin of Video Cable is bent.
Adjust the Contrast and Brightness Controls.
Picture bounces or a
• Move electrical devices that may cause electrical
wave pattern is present
interference.
in the picture.
The power LED is ON • Computer Power Switch should be in the ON position.
but there’s no video or • Computer Video Card should be snugly seated in its
no picture.
slot
• Make sure monitor’s video cable is properly connected
to the computer.
• Inspect monitor’s video cable and make sure none of
the pins are bent.
• Make sure computer is operational by hitting the
CAPS LOCK key on the keyboard while observing the
CAPS LOCK LED. The LED should either turn ON or
OFF after hitting the CAPS LOCK key.
Missing one of the
primary colors (RED,
GREEN, or BLUE).
• Inspect the monitor’s video cable and make sure that
none of the pins are bent.
Screen image is not
centered or sized
properly.
• Adjust pixel frequency (CLOCK) and PHASE or press
hot-key (AUTO).
Picture has color
• Adjust RGB color or select color temperature.
defects (white does not
look white)
Horizontal or vertical
disturbances on the
screen.
• Use Win95/98/2000/ME/XP shut-down mode Adjust
CLOCK and PHASE or perform hot- key (AUTO-key).
CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal
sweep. If the frequency is not correct, the screen shows vertical stripes and the
picture has not correct width. PHASE adjusts the phase of the pixel clock signal.
With a wrong phase adjustment the picture has horizontal disturbances in light
picture. For PHASE and CLOCK adjustment use “dot-pattern” or Win95/98/2000/
ME/XP shut-down mode pattern.
16
TECHNICAL SUPPORT (FAQ)
ERROR MESSAGE & POSSIBLE SOLUTION
CABLE NOT CONNECTED :
1. Check that the signal-cable is properly connected. If the connector is loose,
tighten the connector’s screws.
2. Check the signal cable connection pins for damage.
INPUT NOT SUPPORT :
Your computer has been set to unsuitable display mode, set the computer to
display mode given in the following table.(page 20)
17
APPENDIX
SPECIFICATIONS
Specifications
Panel Type
LCD Panel
Frequency
(H/V)
Input
Audio
Touch
Screen
Web cam
Power
Panel Size
Pixel Pitch (mm)
Max. Resolution
Display Colour
H. Freq.
V. Freq.
VGA
HDMI
DisplayPort
Audio in
Speaker
Touch Technology
Input Method
Resolution
Touch Accuracy
Microsoft
Operating Windows 8
Systems Microsoft
Windows 7
Resolution
Power Supply
Consumption Max.
Consumption Standby
TM-22
TM-23
TM-27
LED-backlit
TFT LCD
21.5"
0.248 x 0.248
LED-backlit
LED-backlit
TFT LCD
TFT LCD
23.0"
27.0"
0.265 x 0.265
0.311 x 0.311
1920 x 1080
16.7 M
30KHz – 83KHz
50Hz - 76Hz
15-Pin D-Sub 15-Pin D-Sub
15-Pin D-Sub
HDMI
HDMI
HDMI
DisplayPort
DisplayPort
DisplayPort
1 x stereo audio in for PC (audio jack, 3.5 Ø)
2W x 2
Projected Capacitive Touch
Finger or Cap. Stylus
25ppi(Min.)
Within 1mm each target &10% Jitter limit on
moving
Multi -Touch(10points, plug & play)
Multi -Touch(10points, plug & play)
-
2 Mega-pixel
100~240V, 50/60Hz, 1.5A
< 55W (On)
< 58W (On)
< 73W (On)
< 0.5W (w/o
< 0.5W (w/o
< 3W (w/o
touch)
touch)
touch)
18
APPENDIX
Specifications
Switch
•
•
•
•
•
Functions
•
•
•
•
•
•
•
External
Control
Plug & Play
Operating
Conditions
Storage
Conditions
Temperature
Humidity
Temperature
Humidity
Weight (with base)
Weight
Weight (w/o base)
Packaging Weight
Dimension
TM-22
With Base
TM-23
TM-27
UP/Volume+
DOWN/ECO
AUTO/SOURCE/EXIT
MENU/ENTER
POWER BUTTON
Luminance
Image Setup
Color Temp.
Color Boost
Picture Boost
OSD Setup
Extra
VESA DDC1/2BTM
0°C ~ 40°C (32°F ~ 104°F)
10% ~ 85%
-25°C ~ 55°C (-13°F ~ 131°F)
5% ~ 93%
6.6 kg
7.4 kg
11.0 kg
(14.5 lbs)
(16.3 lbs)
(24.2 lbs)
4.3 kg
5.1 kg
6.6 kg
(9.5 lbs)
(11.2 lbs)
(14.5 lbs)
8.5 kg
9.4 kg
12.8 kg
(18.7 lbs)
(20.7 lbs)
(28.2 lbs)
522.4 x 238.5 x 561 x 238.5
660 x 328.5 x
385 mm
x 422.6 mm
454 mm
(20.6" x 9.4" x (22.1” x 9.4” x (26.0" x 12.9" x
15.2")
16.6”)
17.9")
Note: All specifications are subject to change without prior notice.
19
APPENDIX
FACTORY PRESET TIMING TABLE
Preset Display Modes
Horizontal
Vertical
Frequency (KHz)
Frequency (Hz)
640×480 @60Hz
31.469
59.940
640×480 @67Hz
35.000
66.667
640×480 @72Hz
37.861
72.809
640×480 @75Hz
37.500
75.000
720×400 @70Hz
31.469
70.087
800×600 @56Hz
35.156
56.250
800×600 @60Hz
37.879
60.317
800×600 @72Hz
48.077
72.188
800×600 @75Hz
46.875
75.000
832×624 @75Hz
49.725
74.550
1024×768 @60Hz
48.363
60.004
1024×768 @70Hz
56.476
70.069
1024×768 @75Hz
60.023
75.029
1280x720@60Hz
60.000
60.000
SXGA
1280x960@60Hz
1280x1024@60Hz
1280x1024@75Hz
44.772
63.981
79.976
59.855
60.020
75.025
WSXGA
1440x900@60Hz
55.935
59.887
WSXGA+
1680x1050@60Hz
65.290
59.954
FULL HD
1920x1080@60Hz
67.500
60.000
Standard
VGA
Dos-mode
SVGA
Mac-Mode
XGA
Resolution
20
APPENDIX
HDMI & DP Timing Table
Format
Resolution
Vertical Frequency
480P
640 x 480
60Hz
480P
720 x 480
60Hz
576P
720 x 576
50Hz
720P
1280 x720
50Hz,60Hz
1080I
1920 x 1080
50Hz,60Hz
1080P
1920 x 1080
50Hz,60Hz
CONNECTOR PIN ASSIGNMENT
1
5
6
10
11
15
Figure 6 15-Pin Color Display Signal Cable
Pin No.
Description
Pin No.
Description
1
Red
9
+5V/Sense(+5V)
2
Green
10
Monitor Gnd
3
Blue
11
Logic Gnd
4
Logic Gnd
12
DDC serial data
5
Detect cable
13
H sync
6
Red Gnd
14
V sync
7
Green Gnd
15
DDC serial Clk.
8
Blue Gnd
21
APPENDIX
Figure 7 20-Pin Display Port Signal Cable
Pin No.
Mnemonic
Signal
1
ML Lane 3 (n)
Lane 3 -
2
GND
Ground
3
ML Lane 3 (p)
Lane 3 +
4
ML Lane 2 (n)
Lane 2 -
5
GND
Ground
6
ML Lane 2 (p)
Lane 2 +
7
ML Lane 1 (n)
Lane 1 -
8
GND
Ground
9
ML Lane 1 (p)
Lane 1 p
10
ML Lane 0 (n)
Lane 0 -
11
GND
Ground
12
ML Lane 0 (p)
Lane 0 +
13
GND
Ground
14
GND
Ground
15
AUX CH (p)
Aux Channel +
16
GND
Ground
17
AUX CH (n)
Aux Channel -
18
HPD
Hot Plug Detect
19
Return
Return
20
DP PWR
NC
22
APPENDIX
Figure 8 HDMI Signal Cable
Pin No.
1
Signal Name
Pin No.
TMDS Data 2+
11
Signal Name
TMDS Clock Shield
2
TMDS Data 2 Shield
12
TMDS Clock
3
TMDS Data 2
13
CEC
4
TMDS Data 1+
14
Reserved (N.C. on device)
5
TMDS Data 1 Shield
15
SCL
6
TMDS Data 1
16
SDA
7
TMDS Data 0+
17
DDC/CEC Ground
8
TMDS Data 0 Shield
18
+5V Power
9
TMDS Data 0
19
Hot Plug Detect
10
TMDS Clock +
23
PRODUCT DIMENSIONS
522.4 mm
318.4 mm
385.0 mm
► Front View
► Side View
57.2 mm
► Top View
238.5 mm
TM-22
229.9 mm
24
TM-23
561.0 mm
338.2 mm
422.6 mm
► Front View
57.2 mm
► Side View
15
7
5.
m
m
238.5 mm
► Top View
229.9 mm
25
TM-27
659.5 mm
409.3mm
454.0 mm
► Front View
56.0 mm
► Side View
328.5 mm
► Top View
318.8 mm
Company Address: 5F-1, No. 3-1, Park Street, Nangang District, Taipei, 11503, Taiwan.
26

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement