- Computers & electronics
- Telecom & navigation
- Mobile phones
- Car kits
- NAV-TV
- Barracuda CTS
- Owner's manual
advertisement
Jack Randall
March 24, 2010
100 NW 11 th Street, Boca Raton, FL 33432 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com
Barracuda-CTS
Installation Addendum of the Barracuda for the CTS.
Installation
1. Using a plastic pry tool, remove the trim panel that goes across the dash.
2. With the plastic pry tool, pry up the (2) trim panels around the gear selector panel.
3. Place the vehicle into “Drive”, BUT DO NOT START
THE VEHICLE. Pull up the gear selector panel and pull up around the shifter.
4. Remove the (2) 7mm screws from around the radio/HVAC panel.
5. Once the 7mm screws are removed, gently pry around the panel and remove. Disconnect the trim panel wiring and cigarette lighter plug.
6. Remove the (4) 7mm screws from around the radio. Remove the radio.
7. Unplug the radio harness.
8. Locate the main, 44-pin harness. This is where the
GMLAN, power and ground connections will be made. The GMLAN wire gets cut in half. Power and ground get spliced in. a. Pin 9 Barracuda connector (green) GMLAN- connects to pin 28 (dark green) of the GM connector going towards the radio. b. Pin 18 Barracuda connector (purple) GMLAN- connects to pin 28 (dark green) of the GM connector going towards the vehicle. c. Pin 1 Barracuda connector (Red) power- splice into pin 44 of GM connector. d. Pin 10 Barracuda connector (black) ground- splice into pin 38 of GM connector.
9. Once all connections are complete, reassemble and test.
10. Use the Barracuda instruction manual for system setup and operation.
All wires need to be soldered and insulated.
The GPS antenna relay is not used.
Remove
7mm
1 |
P a g e
Agreement
:
End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger entertainment only.
Jack Randall
March 24, 2010
Installing with GVIF-CTS for backup camera
1. Install GVIF-CTS according to installation manual.
2. Power for the module can be connected to the
Barracuda’s “Output B”. Be sure to set “Output
B” to Acc output in the menu.
3. The blue wire from the Barracuda (rear camera
12v out) gets connected to the gray wire on the GVIF.
1.
14.
15.
16.
17.
18.
10.
11.
12.
13.
6.
7.
8.
9.
2.
3.
4.
5.
Barracuda
12v constant
Wire connections
GM conn
Pin 44
No Use
No Use
No Use
RX
Camera to radio
Camera shield
VSS to Radio
GMLAN to radio
Ground
Rear Cam 12v out
Output A
Output B
TX
Front Cam In
Rear Cam In
VSS to vehicle
GMLAN to vehicle
Pin 38
N/A
Pin 28
N/A
Pin 28
GVIF
Gray
Red
Rear-C
Connectors
Wire view of Barracuda connector
Front view of GM connector
2 |
P a g e
Agreement
:
End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger entertainment only.
advertisement
Related manuals
advertisement