Always there to help you
Register your product and get support at
www.philips.com/welcome
Question?
Contact
Philips
User manual
BDP5650
English
Safety and important
notice
Read and understand all instructions before you
use this Blu-ray disc/ DVD player. If damage is
caused by failure to follow the instructions, the
warranty does not apply.
Safety
Risk of electric shock or fire!
• Never expose the product and accessories
to rain or water. Never place liquid
containers, such as vases, near the product.
If liquids are spilt on or into the product,
disconnect it from the power outlet
immediately. Contact Philips Consumer
Care to have the product checked before
use.
• Never place the product and accessories
near naked flames or other heat sources,
including direct sunlight.
• Never insert objects into the ventilation
slots or other openings on the product.
• Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
• Batteries (battery pack or batteries
installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
• Disconnect the product from the power
outlet before lightning storms.
• When you disconnect the power cord,
always pull the plug, never the cable.
Risk of short circuit or fire!
• Before you connect the product to the
power outlet, ensure that the power
voltage matches the value printed on the
back or bottom of the product. Never
2
connect the product to the power outlet if
the voltage is different.
Risk of injury or damage to the product!
• Visible and invisible laser radiation when
open. Avoid exposure to beam.
• Do not touch the disc optical lens inside
the disc compartment.
• Never place the product or any objects
on power cords or on other electrical
equipment.
• If the product is transported in
temperatures below 5°C, unpack the
product and wait until its temperature
matches room temperature before
connecting it to the power outlet.
Risk of overheating!
• Never install this product in a confined
space. Always leave a space of at least four
inches around the product for ventilation.
Make sure that curtains or other objects
never cover the ventilation slots on the
product.
Risk of contamination!
• Do not mix batteries (old and new or
carbon and alkaline, etc.).
• Remove batteries if they are exhausted or
if the remote control is not to be used for
a long time.
• Batteries contain chemical substances, they
should be disposed of properly.
Risk of swallowing batteries!
• The product/remote control may contain a
coin type battery, which can be swallowed.
• Keep the battery out of reach of children
at all times!
Class II equipment symbol:
This symbol indicates that this product has a
double insulation system.
CLASS 1
LASER PRODUCT
3D health warning
•
•
•
If you or your family has a history of
epilepsy or photosensitive seizures, consult
a medical professional before exposing
yourself to flashing light sources, rapid
image sequences or 3D viewing.
To avoid discomfort such as dizziness,
headache or disorientation, we
recommend not watching 3D for extended
periods of time. If you experience any
discomfort, stop watching 3D and do
not immediately engage in any potentially
hazardous activity (for example driving a
car) until your symptoms have disappeared.
If symptoms persist, do not resume
watching 3D without consulting a medical
professional first.
Parents should monitor their children
during 3D viewing and ensure they do not
experience any discomfort as mentioned
above. Watching 3D is not recommended
for children under 6 years of age as their
visual system is not fully developed yet.
Care for your product
•
•
•
•
Do not insert any objects other than discs
into the disc compartment.
Do not insert warped or cracked discs into
the disc compartment.
Remove discs from the disc compartment
if you are not using the product for an
extended period of time.
Only use microfiber cloth to clean the
product.
Care of the environment
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC. Please inform yourself about the local
separate collection system for electrical and
electronic products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negative consequences for the environment and
human health.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot
be disposed with normal household waste.
Please inform yourself about the local rules
on separate collection of batteries because
correct disposal helps to prevent negative
consequences for the environmental and
human health.
Compliance
This product complies with the radio
interference requirements of the European
Community.
3
Hereby, Philips Consumer Lifestyle, declares
that this product is in compliance with the
essential requirements and other relevant
provisions of Directive 1999/5/EC. You
can find the Declaration of Conformity on
www.p4c.philips.com.
Copyright
This item incorporates copy protection
technology that is protected by U.S. patents
and other intellectual property rights of
Rovi Corporation. Reverse engineering and
disassembly are prohibited.
Open source software
Philips Electronics Singapore Pte Ltd hereby
offers to deliver, upon request, a copy of the
complete corresponding source code for the
copyrighted open source software packages
used in this product for which such offer is
requested by the respective licenses.
This offer is valid up to three years after
product purchase to anyone in receipt of this
information. To obtain source code, please
contact open.source@philips.com. If you prefer
not to use email or if you do not receive
confirmation receipt within a week after mailing
to this email address, please write to "Open
Source Team, Philips Intellectual Property &
Standards, P.O. Box 220, 5600 AE Eindhoven,
The Netherlands." If you do not receive timely
confirmation of your letter, please email to the
email address above.
This product incorporates proprietary
technology under license from Verance
Corporation and is protected by U.S. Patent
7,369,677 and other U.S. and worldwide
patents issued and pending as well as copyright
and trade secret protection for certain aspects
of such technology. Cinavia is a trademark
of Verance Corporation. Copyright 20042013 Verance Corporation. All rights reserved
4
by Verance. Reverse engineering or disassembly
is prohibited.
Cinavia notice
This product uses Cinavia technology to
limit the use of unauthorized copies of some
commercially-produced film and videos and
their soundtracks. When a prohibited use of an
unauthorized copy is detected, a message will
be displayed and playback or copying will be
interrupted.
More information about Cinavia technology
is provided at the Cinavia Online Consumer
Information Center at http://www.cinavia.com.
To request additional information about Cinavia
by mail, send a postcard with your mailing
address to: Cinavia Consumer Information
Center, P.O. Box 86851, San Diego, CA, 92138,
USA.
Register your product and get support at
www.philips.com/welcome
1
HDMI OUT
(
)
OPTICAL
5
2
HDMI OUT
HDMI O
OUT
OPTICAL
OPTICAL
6
3
4
5
1
2
SOURCE
TV
7
6
2
BD
BD 3D
DVD/VCD/CD
DivX Plus HD/MKV
MP3 / JPEG
1
3
4
USB
2
3
8
1
Contents
1 Use your Blu-ray disc/ DVD player 2
Basic play control
Video, audio and picture options
DivX videos
Play a musical slideshow
BonusView on Blu-ray
BD-Live on Blu-ray
Play a Blu-ray 3D video
Set up a network
Smartphone control
Browse PC through DLNA
Browse Smart TV
Rent online videos
Stream media from an Android device
Stream multimedia via Miracast
Use Philips EasyLink
2
3
4
5
5
5
6
6
7
7
8
8
9
9
9
2 Change settings
10
Picture10
Sound10
Network (installation, Smart TV...)
10
Preference (languages, parental control...)11
Advanced options (clear memory...)
12
3 Update software
12
12
12
4 Specifications
13
5Troubleshooting
14
Update software via the Internet
Update software via USB
EN
1
1 Use your Bluray disc/ DVD
player
Basic play control
Congratulations on your purchase, and
welcome to Philips! To fully benefit from
the support that Philips offers (e.g. product
software upgrade), register your product at
www.philips.com/welcome.
During play, press the following buttons to
control.
2
EN
Button
Action
SMART TV
Turn on the player, or switch
to standby.
Access the home menu.
Select to connect to Smart TV.
Button
Action
DISC MENU
Access or exit the disc menu
or Pop-up menu.
Access the main menu of a
video disc.
Navigate the menus.
Press
to rotate a picture
clockwise or counter-clockwise
during slideshow.
Confirm a selection or entry.
Return to a previous display
menu.
Access more options during
play.
Select tasks or options for
Blu-ray discs.
Open or close the disc
compartment.
Start or resume play.
Pause play.
Press repeatedly to slow
forward frame by frame.
Stop play.
Skip to the previous or next
track, chapter or file.
Fast backward or forward.
Press repeatedly to change the
search speed.
Press once, and then press
to slow forward.
Select an audio language or
channel.
Select a subtitle language.
Select an item to play.
Enter values.
Enter letters via SMS style
entry.
TOP MENU
OK
Color
buttons
/
/
AUDIO
SUBTITLE
Alphanumeric
buttons
Video, audio and picture
options
More options are available for video or picture
play from a disc or USB storage device.
Video options
2
3
1
Access more options during video play.
• [Audio Language]: Select an audio
language.
• [Subtitle Language]: Select a subtitle
language.
• [Subtitle Shift]: Change the subtitle
position on the screen. Press
to
change the subtitle position.
• [Info]: Display play information.
• [Character Set]: Select a character set that
supports the DivX video subtitle (only for
DivX videos).
• [Time Search]: Skip to a specific time
via the numeric buttons on the remote
control.
• [2nd Audio Language]: Select the second
audio language (only for Blu-ray discs that
support BonusView).
• [2nd Subtitle Language]: Select the second
subtitle language (only for Blu-ray discs that
support BonusView).
• [Titles]: Select a title.
• [Chapters]: Select a chapter.
• [Angle List]: Select a camera angle.
• [Menus]: Display a disc menu.
• [PIP Selection]: Display a picture-in-picture
window (only for Blu-ray discs that support
BonusView).
EN
3
[Zoom]: Zoom into a video picture. Press
to select a zoom factor.
[Repeat]: Repeat a chapter or title.
[Repeat A-B]: Mark two points within a
chapter for repeat play, or turn off repeat
mode.
[Picture Settings]: Select a predefined
color setting.
•
•
•
•
Note
•• Available video options depend on the video source.
Picture options
Press repeatedly to cycle through the
following options.
• Repeat the current track.
• Repeat all the tracks on the disc or folder.
• Play audio tracks in a random loop.
• Turn off a repeat mode.
DivX videos
2
You can play DivX videos from a disc, a USB
storage device, or an online video store (see
"Rent online videos).
3
1
Access more options during slideshow.
• [Rotate +90]: Rotate a picture 90 degrees
clockwise.
• [Rotate -90]: Rotate a picture 90 degrees
counter-clockwise.
• [Zoom]: Zoom into a picture. Press
to
select a zoom factor.
• [Info]: Display picture information.
• [Duration per slide]: Set a display interval
for a slideshow.
• [Slide Animation]: Select a transition effect
for a slideshow.
• [Picture Settings]: Select a predefined
color setting.
• [Repeat]: Repeat a selected folder.
4
Audio options
EN
VOD code for DivX
• Before you purchase DivX videos and play
them on this player, register this player on
www.divx.com using the DivX VOD code.
• Display the DivX VOD code: press , and
select [Setup] > [Advanced] > [DivX®
VOD Code].
DivX subtitles
• Press SUBTITLE to select a language.
• If the subtitle is not displayed correctly,
change the character set that supports the
DivX subtitle. Select a character set: press
, and select [Character set].
Character
set
Languages
[Standard]
English, Albanian, Danish, Dutch,
Finnish, French, Gaelic, German,
Italian, Kurdish (Latin), Norwegian,
Portuguese, Spanish, Swedish, and
Turkish
Character
set
Languages
[Central
Europe]
Albanian, Croat, Czech, Dutch,
English, German, Hungarian, Irish,
Polish, Romanian, Slovak, Slovene,
and Serbian
Bulgarian, Belorussian, English,
Macedonian, Moldavian, Russian,
Serbian, and Ukrainian
Greek
Estonian, Latvian and Lithuanian
Simplified Chinese
Traditional Chinese
[Cyrillic]
[Greek]
[Baltic]
[Chinese]
[ChineseTraditional]
[Korean]
BonusView on Blu-ray
View special content (such as commentaries) in
a small screen window.
This feature is only applicable to Blu-ray discs
compatible with BonusView (also known as
picture in picture).
1
2
English and Korean
3
Note
•• To use the subtitles, make sure that the subtitle file
has the same name as the DivX video file name. For
example, if the DivX video file is named “movie.avi",
save the subtitle file as “movie.srt”, or “movie.sub”.
•• This player can play subtitle files in the following
formats: .srt, .sub, .txt, .ssa, and .smi.
Play a musical slideshow
Play music and pictures simultaneously to create
a musical slideshow.
1
2
3
4
5
From a disc or connected USB storage
device, play a music file.
Press
Press
again to stop music play.
»» The secondary video window is
displayed.
Select [2nd Audio Language] or [2nd
Subtitle Language], and press OK.
Access exclusive online services, such as movie
trailers, games, ringtones and other bonus
contents.
This feature is only applicable to Blu-ray discs
that are BD-Live enabled.
1
2
, and go to the picture folder.
to stop slideshow.
Select [PIP Selection] > [PIP], and press
OK.
»» PIP options [1]/[2] depend on the
video contents.
BD-Live on Blu-ray
Select a picture from the same disc or
USB, and press OK to start slideshow.
Press
During play, press .
»» The options menu is displayed.
3
4
Prepare the Internet connection and set
up a network (see "Set up a network").
Connect a USB storage device to the
(USB) connector on this player.
• A USB storage device is used to store
the downloaded BD-Live content.
• To delete the BD-Live previously
downloaded on the USB storage
device for memory release, press
and select [Setup] > [Advanced] >
[Clear memory].
Play a disc that is BD-Live enabled.
On the disc menu, select the BD-Live icon,
and press OK.
»» BD-Live starts to load. The loading
time depends on the disc and the
Internet connection.
EN
5
5
On the BD-Live interface, select an item
to access.
1
Note
•• BD-Live services vary from discs and countries.
•• When you use BD-Live, data on the disc and this player
are accessed by the content provider
Connect this player to a computer
network and the Internet, through wired
(Ethernet) or wireless connection.
• For wired connection, connect a
network cable (not supplied) to the
LAN port on the back panel of this
player.
•• Use a USB storage device with at least 1GB of free
space to store the download.
•• If a USB hub is used with this player, do not overload
the USB hub with many USB devices to avoid
insufficient USB power.
PC (DLNA)
Play a Blu-ray 3D video
What you need
• A 3D compliant TV
• This player is connected to the TV through
HDMI
• 3D glasses compatible with the TV
• 3D Blu-ray disc
1
2
3
• This player has a built-in Wi-Fi for a
wireless connection.
Make sure that 3D output is turned on:
press , and select [Setup] > [Video]
>[Watch 3D video] > [Auto].
Play a Blu-ray 3D video.
PC (DLNA)
Put on the 3D glasses for 3D effects.
• To turn off 3D output, press , and
select [Setup] > [Video] > [Watch 3D
video] > [Off].
Set up a network
Connect this player to a computer network and
the Internet to access the services:
• Browse PC (DLNA): play photos, music,
and video files streamed from your
computer.
• Smart TV: access online Smart TV services.
• Update software: update the software of
this player via the Internet.
• BD-Live: access online bonus features
(applicable to Blu-ray discs that are BDLive enabled).
6
EN
2
Perform the network installation.
1) Press .
2) Select [Setup], and press OK.
3) Select [Network] > [Network
installation], and press OK.
4) Follow the instructions on the TV screen to
complete the installation.
Caution
4
•• Before you connect to a network, familiarize yourself with
the network router, media server software for DLNA, and
networking principles. If necessary, read documentation
accompanying network components. Philips is not
responsible for lost, damaged, or corrupt data.
5
Smartphone control
Use a smartphone to browse, control and play
media files from this player.
What you need
• An iPhone (iOS 3.1.3 and above) or
Android based device (Android 2.1 and
above)
• On your smartphone, download Philips
MyRemote application
• For iPhone, search for the application
in App Store
• For Android based device, search for
the application in Android Market
Before you start
• Connect this player to a home network
(see "Set up a network").
• Connect your smartphone to the same
home network (see the user manual of the
smartphone for details).
• Turn on this player
Control your player
6
2
3
Insert a data disc or USB storage device
into this player.
On your smartphone, tap the MyRemote
icon from the home screen.
»» The name of this player is displayed on
the smartphone.
Select this player from the smartphone
screen.
»» The smartphone used as a virtual
remote control is enabled.
Open a folder, and select a file to play.
• To access the remote control, return
to the previous smartphone screen,
and then tap the Remote (Remote)
tab. Only the relevant control buttons
are enabled.
Tap the control buttons on the
smartphone to control play.
• To access more control buttons, swipe
the screen to the left or right.
• To exit the application, press the home
button on the smartphone.
Browse PC through DLNA
Through this player, you can stream and play
video, music and photo from a computer on
your TV.
Before you start
• On your PC, install a DLNA-compliant
media server application (such as Windows
Media Player 11 or higher)
• On your PC, enable media sharing and file
sharing (see the "Help" document in the
media server application)
1
Use a smartphone to browse, control and play
media files from this player.
1
On the smartphone, tap the Media
(Media) tab, and then select the disc or
USB source.
»» The folders in the data disc or USB
storage device are displayed.
2
3
4
Connect this player and your PC in the
same home network (see "Set up a
network").
• For better video quality, use wired
network connection whenever possible.
Press .
»» The home menu is displayed on the
TV screen.
Select [browse PC], and press OK.
»» A content browser is displayed.
Select a file, and press OK to play.
• Use the remote control to control play.
EN
7
Browse Smart TV
Rent online videos
You can access variety of Internet applications
and specially adapted Internet websites.
Rent videos from online stores through this
player.
Note
•• Koninklijke Philips Electronics N.V. bears no
responsibility for content provided by Smart TV service
providers.
1
2
3
4
5
Connect this player to the Internet (see
"Set up a network").
Press .
»» The home menu is displayed on the
TV screen.
Select [Smart TV], and press OK.
Follow the onscreen instructions to
confirm the onscreen message.
»» The online services available in your
country are displayed.
Use the remote control to navigate and
select an Internet application.
Button
Action
Navigate and select an a service
or item.
OK
Confirm a selection.
Return to a previous page, or
delete input text.
Access options related to a
current activity.
Alphanumeric Input text (such as an email
buttons
address, web URL and password).
TOP MENU Return to the Smart TV home
screen.
To remove the passwords and cookies from
this player, see the section: Change settings >
Network (installation, Smart TV...).
8
EN
What you need
• A high-speed Internet connection to this
player.
• An HDMI connection between this player
and the TV.
• A USB storage device, with at least 8 GB
memory.
Note
•• Use a blank USB storage device. Formatting a USB
storage device erases any content on the USB storage
device.
•• This service is country dependent.
1
2
3
4
5
6
Connect this player to the Internet (see
"Set up a network").
Insert a blank USB storage device into the
USB connector located on the rear panel
of this player.
Press
.
Select [Smart TV], and press OK.
»» The online services available in your
country are displayed.
Select a video store, and follow the onscreen
instructions to rent and watch a video.
»» The video is downloaded to the USB
storage device. You can watch it now
or at any time within the rental period.
»» For the downloaded video on the USB
storage device, you can watch it only
on this player.
Use the remote control to play and
control the video.
Stream media from an
Android device
With Philips SimplyShare, through this player
you can stream media files from an Android
based device on your TV. For details, visit
www.philips.com/support
Note
•• This player can store up to 10 Miracast devices for
pair-up, and can only connect a single Miracast certified
device at a time.
•• During Miracast connection, Wi-Fi connection on this
player is temporarily suspended.
•• To avoid interference from Bluetooth transmission, turn
off Bluetooth on your Miracast device.
•• During Miracast streaming, video stuttering or audio
dropouts may occur, depending on your environment
(video streaming is up to 720p).
Stream multimedia via
Miracast
Through this player, you can stream audio and
video from a Miracast certified device to your
TV, and the screen of the Miracast device is
viewed on your TV.
What you need
• Smartphones or tablets with Android 4.2/
Windows 8.1 or above, and check those
devices on whether Miracast feature is
available (the name of Miracast feature
may vary on different devices).
• Enable Miracast on your smartphone or
tablet (refer to a related user manual for
details).
• Make sure that Miracast is enabled on
this player (press , and select [Setup] >
[Network] > [Miracast break-in] > [On]).
1
2
3
Press to display the home menu screen
of this player.
On the Miracast source device, initiate
the search for this player and select this
player when it is found (refer to the source
device's user manual for details).
• If this is the first time these 2 devices
are paired, an acknowledgement
message is displayed on your TV.
Accept it to continue the pairing.
• To cancel the pairing, press on the
remote control.
Wait until the media content from the
source device is displayed on your TV, then
choose the media to start play.
»» Audio or video is streamed to your TV
through this player.
Use Philips EasyLink
This player supports Philips EasyLink which
uses the HDMI CEC (Consumer Electronics
Control) protocol. You can use a single remote
control to control EasyLink compliant devices
that are connected through HDMI. Philips does
not guarantee 100% interoperability with all
HDMI CEC devices.
1
2
3
4
Connect the HDMI CEC compliant devices
through HDMI, and turn on the HDMI
CEC operations on the TV and other
connected devices (see the user manual of
the TV or other devices for details).
Press
.
Select [Setup]> [EasyLink].
Select [On] under the options: [EasyLink],
[One Touch Play] and [One Touch
Standby].
»» EasyLink function is turned on.
One Touch Play
When a video disc is in the disc compartment,
press to wake up the TV from standby, and
then play a disc.
One Touch Standby
When a connected device (for example TV)
is put to standby with its own remote control,
this player is put to standby automatically.
EN
9
2 Change settings
Note
•• If you change a setting, make sure that the TV supports
the new setting.
This section helps you change the settings of
this player.
1
Sound
2
1
2
•
3
Watch 3D video
•
•
Note
•• You cannot change a menu option that is grayed out.
•• To return to the previous menu, press . To exit the
menu, press
.
•
Picture
1
2
•
•
•
•
•
10
Press
.
Select [Setup] > [Video] to access the
video setup options.
[TV display]: Select a picture display format
to fit the TV screen.
[HDMI video]: Select an HDMI video
resolution.
[HDMI Deep Color]: Display colors with
more shades and hues when the video
content is recorded in Deep Color and the
TV supports this feature.
[Picture settings]: Select a predefined
color setting.
[Watch 3D video]: Set to 3D or 2D
output when playing a Blu-ray 3D disc.
The player must be connected to a 3D TV
through HDMI.
EN
Press
.
Select [Setup] > [Audio] to access the
audio setup options.
[Night mode]: Select quiet or full dynamic
sound. Night mode decreases the volume
of loud sound and increases the volume of
soft sound (such as speech).
[HDMI Audio]: Set an HDMI audio format
when this player is connected through
HDMI.
[Digital Audio]: Select an audio format
for the sound output when this player is
connected through a digital connector
(OPTICAL).
[PCM Downsampling]: Set the sampling
rate for PCM audio output when this
player is connected through a digital
connector (OPTICAL).
Note
•• For settings related to HDMI, the TV must be
connected through HDMI.
•• Night mode is only available for Dolby encoded DVD
and Blu-ray discs.
Network (installation, Smart
TV...)
1
2
Press
.
Select [Setup] > [Network] to access the
network setup options.
•
•
•
•
•
•
•
•
[Network installation]: Start a wired or
wireless installation to make the network
work.
[View network settings]: Display the
current network status.
[View wireless settings]: Display the
current Wi-Fi status.
[Clear Smart TV memory]: Clear the
history of Smart TV browser (such as
cookies).
[Name your Product:]: Re-name this
player for identification in a home network.
[Miracast break-in]: Turn on or off
Miracast.
[Miracast browser]: Scan for Miracast
devices.
[Miracast role]: Force this player to be
Group Owner or automatically choose a
device to be Group Owner.
• [Auto]: The role of Group owner is
automatically determined between the
source device and this player when
connection is established.
• [Group Owner]: Force this player to
be Group Owner and allow it to select
the channel to use for establishing the
link with the source device.
Preference (languages,
parental control...)
1
2
•
•
•
•
•
•
Press
.
Select [Setup] > [Preference] to access
the preference setup options.
[Menu language]: Select an onscreen
display menu language.
[Keyboard layout]: Select a language for a
connected keyboard.
[Audio]: Select an audio language for video.
[Subtitle]: Select a subtitle language for
video.
[Disc Menu]: Select a menu language for a
video disc.
[Parental Control]: Restrict access to discs
that are encoded with ratings. Input "0000"
•
•
•
•
•
•
•
•
•
to access the restriction options. To play all
discs irrespective of the rating, select level
"8".
[Screen Saver]: Enable or disable screen
saver mode. If enabled, the screen enters
idle mode after 10 minutes of inactivity (for
example, in pause or stop mode).
[Auto Subtitle Shift]: Enable or disable
subtitle shift. If enabled, the subtitle position
is changed automatically to fit the TV
screen (this feature works with some
Philips TVs only).
[Change Password]: Set or change a
password to play a restricted disc. Input
"0000" if you do not have a password or if
you have forgotten your password.
[Display Panel]: Change the brightness of
the display panel of the player.
[Auto Standby]: Enable or disable auto
standby. If enabled, the player switches to
standby after 30 minutes of inactivity (for
example, in pause or stop mode).
[Fast wake up]: Enable or disable the
player to wake up faster from standby. If
fast wakeup is turned off, less power is
consumed during standby.
[VCD PBC]: Display or skip the content
menu for VCD and SVCD.
[Auto play disc]: Enable or disable the
automatic disc playback after power on.
[Auto play after video]: Enable or disable
sequential playback of videos from USB
or PC.
Note
•• If your preferred language is not available for disc
language, audio or subtitle, you can select [Other]
from the menu options and input 4-digit language code
which can be found at the back of this user manual.
•• If you select a language which is not available on a disc,
this player uses the default language of the disc.
EN
11
Advanced options (clear
memory...)
1
2
•
•
•
•
•
•
•
Press
.
Select [Setup] > [Advanced] to access the
advanced setup options.
[BD-Live security]: Restrict or allow access
to BD-Live (only for non-commercial, usercreated BD-Live discs).
[Downmix mode]: Control 2-channel
stereo audio output.
[Software update]: Select to update
software from a network or from USB
storage device.
[Clear memory]: Delete the previous BDLive download on the USB storage device.
A "BUDA" folder is automatically created
to store the BD-Live download.
[DivX® VOD Code]: Display the DivX®
registration code or the deregistration
code for this player.
[Version information]: Display the
software version of this player.
[Restore default settings]: Reset this player
to the default settings made at the factory,
except for password and parental control
level.
Note
•• You cannot restrict Internet access on commercial
Blu-ray discs.
•• Before you purchase DivX videos and play them on this
3 Update software
Before you update the software of this player,
check the current software version:
• Press , and then select [Setup] >
[Advanced] > [Version information], and
press OK.
Update software via the
Internet
1
2
3
4
Connect the player to the Internet (see
"Set up a network").
Press
, and select [Setup].
Select [Advanced] > [Software update]>
[Network].
»» If an upgrade media is detected, you
are prompted to start the update.
Follow the instructions on the TV screen
to update the software.
»» When the update is complete, this
player automatically turns off and on
again.
Update software via USB
1
player, register this player on www.divx.com with the
DivX VOD code.
2
Check the latest software version on
www.philips.com/support.
• Search for your model and click on
"Software and drivers".
Download the software into a USB storage
device.
aUnzip the download, and make sure
that the unzipped folder is named
"UPG".
3
12
EN
bPut the "UPG" folder in the root
directory.
Connect the USB storage device to the
(USB) connector on this player.
4
5
6
Press
, and select [Setup].
Select [Advanced] > [Software update]>
[USB].
»» If an upgrade media is detected, you
are prompted to start the update.
Follow the instructions on the TV screen
to update the software.
»» When the update is complete, this
player automatically turns off and on
again.
Caution
•• Do not turn off the power or remove the USB storage
device when the software update is in progress because
you might damage this player.
4Specifications
Note
•• Specifications are subject to change without notice
Region code
This player can play discs with the following
region codes.
DVD
Blu-ray
C
Countries
Russia, India
Playable media
• BD-Video, BD 3D
• DVD-Video, DVD+R/+RW, DVD-R/-RW,
DVD+R/-R DL (Dual Layer)
• VCD/SVCD
• Audio CD, CD-R/CD-RW, MP3 media,
WMA media, JPEG files
• DivX (Ultra)/DivX Plus HD media, MKV
media
• USB storage device
File format
• Video: .avi, .divx, .mp4, .mkv, .wmv
• Audio: .mp3, .wma, .wav
• Picture: .jpg, .gif, .png
Video
• Signal system: PAL / NTSC
• HDMI output: 480i/576i, 480p/576p, 720p,
1080i, 1080p, 1080p/24Hz
Audio
• Digital output: 0.5 Vp-p (75 ohm)
• Optical
• HDMI output
• Sampling frequency:
• MP3: 32 kHz, 44.1 kHz, 48 kHz
• WMA: 44.1 kHz, 48 kHz
• Constant bit rate:
• MP3: 112 kbps - 320 kpbs
• WMA: 48 kpbs - 192 kpbs
EN
13
USB
• Compatibility: Hi-Speed USB (2.0)
• Class support: USB Mass Storage Class
• File system: FAT16, FAT32
• USB port: 5V , 500mA (for each port)
• Support HDD (a portable hard disc drive):
an external power source may be needed.
Main unit
• Power supply rating: 220-240V~, 50-60 Hz
• Power consumption: 16 W
• Power consumption in standby mode (fast
wakeup disabled): < 0.5 W
• Dimensions (w x h x d):
360 x 42 x 219 (mm)
• Net Weight: 1.18 kg
Accessories supplied
• Remote control and batteries
• User manual
Laser Specification
• Laser Type (Diode): AlGaInN (BD),
AlGaInP (DVD/CD)
• Wave length:
405+7nm/-7nm (BD), 660+10nm/-10nm
(DVD), 785+10/-10nm (CD)
• Output power: 1mW (BD),
0.26mW (DVD), 0.3mW (CD)
Operating Temperature & Humidity
• 0°C to 45°C, 5% to 90% Humidity for all
climates.
Storage Temperature & Humidity
• -40 °C to 70 °C, 5% to 95%
5Troubleshooting
Note
•• For identification and supply ratings, see the type plate
at the back or bottom of the product.
•• Before you make or change any connections, make sure
that all devices are disconnected from the power outlet.
Warning
•• Risk of electric shock. Never remove the casing of the
player.
To keep the warranty valid, never try to repair
the player yourself.
If you have problems using this player, check the
following points before you request service. If
you still have a problem, register your player and
get support at www.philips.com/support.
If you contact Philips, you will be asked for the
model and serial number of this player. The
model number and serial number are on the
back of this player. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Main unit
The buttons on this player do not work.
• Disconnect this player from the power
supply for a few minutes, and then
reconnect.
Picture
No picture.
• Make sure that the TV is switched to the
correct source input for this player.
No picture on HDMI connection.
• Make sure that the HDMI cable is not
faulty. If it is faulty, replace with a new
HDMI cable.
14
EN
•
•
On the remote control, press and then
press “731” (numeric buttons) to recover
picture display. Or wait for 10 seconds for
auto recovery.
If this player is connected to an
unauthorized display device with an HDMI
cable, the audio and video signals may not
be output.
The disc does not play high-definition video.
• Make sure that the disc contains highdefinition video.
• Make sure that the TV supports highdefinition video.
Sound
No audio output from the TV.
• Make sure that the audio cables are
connected to the audio input of the TV.
• Make sure that the TV is switched to the
correct source input for this player.
No audio output from the loudspeakers of
the external audio device (home theater or
amplifier).
• Make sure that the audio cables are
connected to the audio input of the audio
device.
• Switch the external audio device to the
correct audio source input.
No sound on HDMI connection.
• You may not hear any sound from the
HDMI output if the connected device
is non-HDCP compliant or only DVIcompatible.
No secondary audio output for Picture-inPicture feature.
• When [Bitstream] under the [HDMI
Audio] or [Digital Audio] menu is selected,
interactive sound like secondary sound for
Picture-in-Picture feature is muted. Deselect [Bitstream].
Play
Cannot play a disc.
• Clean the disc.
• Make sure that the disc is correctly loaded.
• Make sure that this player supports the
disc. See "Specifications".
• Make sure that this player supports the
region code of the DVD or BD.
• For DVD±RW or DVD±R, make sure that
the disc is finalized.
Cannot play DivX video files.
•• Make sure that the DivX video file is
complete.
•• Make sure that the video file name
extension is correct.
DivX subtitles do not display correctly.
•• Make sure that the subtitle file has the
same name as the DivX video file.
•• Make sure that the subtitle file has an
extension name supported by this player
(.srt, .sub, .txt, .ssa, or .smi).
Cannot read the contents of a connected USB
storage.
•• Make sure that the format of the USB
storage device is compatible with this
player.
•• Make sure that the file system on the USB
storage device is supported by this player.
•• For a USB HDD (a portable hard disc
drive), an external power source may be
needed. 'No entry' or 'x' sign is displayed on the TV.
•• The operation is not possible.
EasyLink feature does not work.
• Make sure that this player is connected
to the Philips brand EasyLink TV, and the
EasyLink option is turned on (see "Use
your Blu-ray disc/ DVD player" > "Use
Philips EasyLink").
Cannot access BD-Live features.
• Make sure that this player is connected to
the network (see "Use your Blu-ray disc/
DVD player" > "Set up a network").
EN
15
•
•
•
Make sure that the network installation is
made (see "Use your Blu-ray disc/ DVD
player" > "Set up a network").
Make sure that the Blu-ray disc supports
BD-Live features.
Clear memory storage (see "Change
settings" > "Advanced options (BD-Live
security, clear memory...)").
Cannot download video from an online video
store.
• Make sure that this player is connected to
the network (see “Use your Blu-ray disc/
DVD player” > “Set up a network”).
• Make sure that this player is connected to
the TV through an HDMI cable.
• Make sure that you have paid for the video,
and it is within the rental period.
Network
Wireless network is not found or distorted.
• Make sure that the network is correctly
connected (see "Use your Blu-ray disc/
DVD player" > "Set up a network").
• Make sure that the network installation is
made (see "Use your Blu-ray disc/ DVD
player" > "Set up a network").
• Make sure that the wireless network is
not disturbed by microwave ovens, DECT
phones, or other neighboring Wi-Fi devices.
• If the wireless network does not work
properly, try a wired network installation
(see "Use your Blu-ray disc/ DVD player" >
"Set up a network").
Smart TV does not work.
• Make sure that the network is correctly
connected (see "Use your Blu-ray disc/
DVD player" > "Set up a network").
• Make sure that the network installation is
made (see "Use your Blu-ray disc/ DVD
player" > "Set up a network").
• Check the router connection (refer to the
user manual for the router).
16
EN
Browse PC and Smart TV work slowly.
• Look in your wireless router’s user manual
for information on indoor range, transfer
rate, and other factors of signal quality.
• You need a high speed Internet connection
for your router.
3D videos
Cannot see 3D effects
• Make sure that 3D output is turned on(see
"Use your Blu-ray disc/ DVD player" >
"Play a Blu-ray 3D video").
• Make sure that the disc title being played is
Blu-ray 3D compliant.
• Make sure that the TV is 3D and HDMI
compliant, and the TV is set to 3D mode
(refer to the TV's user manual).
• Make sure that the 3D glasses are activated
(refer to the TV’s user manual).
Miracast
Cannot play and stream online video through
Miracast.
• Make sure that Miracast is enabled on the
Miracast source device (refer to the source
device's user manual).
• Make sure that Miracast is enabled on this
player (see "Use your Blu-ray disc/ DVD
player" > "Stream multimedia via Miracast").
• If the Miracast connection fails or the
media content does not show up
automatically on your TV, press and
select [Setup] > [Network] > [Miracast
role] > [Group owner] > [Auto], then
repeat Miracast connection (see "Use
your Blu-ray disc/ DVD player" > "Stream
multimedia via Miracast").
• Make sure that the Miracast source device
supports playing videos from the internet
while performing Miracast streaming to
external player simultaneously (refer to the
source device's user manual).
Corporation or its subsidiaries and are used
under license.
"Blu-ray 3D " and "Blu-ray 3D " logo are
trademarks of Blu-ray Disc Association.
HDMI, and HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI licensing LLC in
the United States and other countries.
The Wi-Fi CERTIFIED Logo is a certification
mark of the Wi-Fi Alliance.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
ABOUT DIVX VIDEO: DivX® is a digital video
format created by DivX, LLC, a subsidiary
of Rovi Corporation. This is an official DivX
Certified® device that plays DivX video. Visit
divx.com for more information and software
tools to convert your files into DivX videos.
ABOUT DIVX VIDEO-ON-DEMAND: This
DivX Certified® device must be registered
in order to play purchased DivX Video-onDemand (VOD) movies. To obtain your
registration code, locate the DivX VOD section
in your device setup menu. Go to vod.divx.com
for more information on how to complete your
registration.
DivX Certified® to play DivX® and DivX Plus®
HD (H.264/MKV) video up to 1080p HD
including premium content.
DivX®, DivX Certified®, DivX Plus® HD
and associated logos are trademarks of Rovi
For DTS patents,see http://patents.dts.com.
Manufactured under license from DTS Licensing
Limited. DTS, the Symbol, & DTS and the
Symbol together are registered trademarks, and
DTS 2.0+Digital Out is a trademark of DTS, Inc.
© DTS, Inc. ALL Rights Reserved.
BONUSVIEW™
'BD LIVE ' and 'BONUSVIEW ' are
trademarks of Blu-ray Disc Association.
'DVD Video' is a trademark of DVD Format/
Logo Licensing Corporation.
Oracle and Java are registered trademarks of
Oracle and/or its affiliates. Other names may be
trademarks of their respective owners.
EN
17
Specifications are subject to change without notice
© 2014 Koninklijke Philips N.V. All rights reserved.
Trademarks are the property of Koninklijke Philips N.V. or their respective owners.
BDP5650_51_UM_V1.0