DOME CAMERA

O P E R AT I O N M A N U A L

M105-DE100-005

Thank you for choosing our high quality camera.

Before attempting to connect or operate, please read and follow these instructions.

C A U T I O N

These servicing instructions are for use by qualified service personnel only.

To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Use Class 2 Power Supply Only

2

C O N T E N T S

1. CAUTIONS

2. IMPORTANT SAFETY INSTRUCTIONS

3. FEATURES

4. EQUIPMENT AND ACCESSORIES

5. OVERVIEW AND FUNCTION

6. INSTALLATION

7. CONNECTION

8. DIMENSIONS

9. SPECIFICATION

10. OSD MENU STRUCTURE

3

1. CAUTIONS

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

Note

This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio / tv technician for help.

Caution

Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

1. A regulated DC12V 1A power supply is recommended for use with this camera

for the best picture and the most stable operation.

An unregulated power supply can cause damage to the camera.

When unregulated power supply is applied, product warranty will be out of subject.

2. It is recommended that the camera is used with a monitor that has a CCTV quality

75 video impedance level.

If your monitor is switched to high impedance then please adjust accordingly.

3. Do not attempt to disassemble the camera to gain access to the internal componets.

Refer servicing to your dealer.

4. Never face the camera towards the sun or any bright or reflective light, which may

cause smear on the picture and possible damage to the CCD.

5. Do not remove the serial sticker for the warranty service.

6. Do not expose the camera to rain or other types of liquid.

7. The apparatus must be connected to a mains socket-outlet with a protective earthing

connection.

4

1. CAUTIONS

WEEE

(Waste Electrical & Electronic Equipment)

This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract.

This product should not be mixed with other commercial wastes for disposal.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL

This symbol is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

5

2. IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long

periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

6

3. FEATURES

• 1/3 960H SONY EXview HAD CCD II

• High Resolution of 700TV Lines

• OSD Function

• Multi Language

• 2DNR

• Privacy Zone

• Motion Detect

• DC12V / AC24V Dual Voltage

• ATR(Adaptive Tone-curve Reproduction / Digital WDR)

The function provides gradation compensation to improve the contrast of subjects both lowluminance areas and high luminance areas exist in the same picture

• 3-Axis Gimbal

Pan Rotation Tilt Rotation Horizontal Rotation

• Service Video connector

The Service Video Connector also provides the installer with an easy way of configuring the camera.

7

4. EQUIPMENT AND ACCESSORIES

1 DOME CAMERA

2 VIDEO OUTPUT TEST CABLE

3 OPERATION MANUAL

4 SCREW - 3ea

5 TEMPLATE

8

5. OVERVIEW AND FUNCTION

• Name (LED Type)

I R L E D 3 0 e a

P h o t o C e l l

S e r v i c e V i d e o

C o n n e c t o r

• Name (Standard)

OSD Joystick

3-Axis

G i m b a l

• CONTROL FUNCTION

(OSD JOYSTICK)

UP

LEFT RIGHT

DOWN

3-Axis

G i m b a l

S e r v i c e V i d e o

C o n n e c t o r

OSD Joystick

9

6. INSTALLATION

2

1

Lens Focus Knob

Lens Zoom Knob

3

5

4

70˚

7

8

70˚

9

Separate LED Cover (Sunshield Cover) and adjust LENS ZOOM / FOCUS KNOB

After setting the LENS, assemble the

LED Cover (Sunshield Cover).

6

NO

1

2

3

4

5

6

7

8

9

PART NAME

Mount Guide

Housing Bottom

Holder Panning

Holder Tlit

Holder Rotate

Sunshield Cover

Led Cover

Housing Top

Dome Cover

Standard Type

1 0

LED Type

7. CONNECTION

• DUAL(DC 12V/AC24V)

DC 12V / AC 24V

D U A L P O W E R S U P P L Y

B N C F E M A L E

V I D E O

V I D E O I N

• DC 12V

D C 1 2 V

P O W E R S U P P L Y

B N C F E M A L E

V I D E O

V I D E O I N

When you install the camera, please glue up the end of cable to keep it stable in order to protect the camera from the humidity problems.

1 1

8. DIMENSIONS

Unit : mm

Ø100

Ø135

Ø108.5

1 2

9. SPECIFICATION

Signal Format

Image Device

Scanning System

H.Resolution

Scanning Frequency

Total Pixels

Effective Pixels

Electronic Shutter Speed

S/N Ratio

Gamma

Min. Illumination

Sync System

Video Output

OSD

BLC

White Balance

2DNR

ATR

Function

Privacy Masking

Motion Detection

Day & Night

Language

Power

Consumption

Operating Temperature

Storage Temperature

DC12V

Dual

Operating Humidity

Options

Weight

Dimension(mm)

NTSC PAL

1/3 ˝

960H SONY EXview HAD CCD II

2:1 Interlace

700TV Lines

H:15.734KHz, V:59.94Hz

1020(H) X 508(V)

976(H) X 494(V)

1/60 sec

H:15.625KHz, V:50Hz

1020(H) X 596(V)

976(H) X 582(V)

More than 50dB(AGC Off)

1/50 sec r=0.45

COLOR : 0.05Lux/F1.2, BW : 0.02 Lux/F1.2

Internal

1.0 Vp-p Composite(75Ω)

Built in (Inner Key / Joystick)

OFF / BLC / HLC

ATW / PUSH / USER1 / USER2 / ANTI CR / MANUAL / PUSH-LOCK

OFF / ON (Level adjustable)

OFF / ON (Level adjustable)

MIRROR / BRIGHTNESS / CONTRAST / SHARPNESS / HUE / GAIN

4 Zones

4 Zones

AUTO

ENGLISH / JAPANESE / GERMAN / FRENCH / RUSSIAN/

PORTUGUESE / SPANISH / CHINESE

DC 12V, (±10%) Max.120mA

DC 12V, (±10%) Max.150mA / AC 24V, (±10%) Max. 2.3W

-10 ℃ ~ +50 ℃

-20 ℃ ~ +60 ℃

Less than 80%

Dual Power

Approx. 343g

136.4( Φ ) x 95.3(mm)

LED TYPE

Power

Consumption

Min. Illumination

IR LED

IR Beam Range

IR LED Operation

DC12V

Dual

DC 12V, (±10%) Max. 320mA

DC 12V, (±10%) Max 390mA / AC 24V, (±10%) Max. 4.8W

0 Lux (IR LED ON)

850nm, 30ea

Up to 30M

On : 1 Lux, Off : 3 Lux

Specifications and designs are subject to change for improving the functionality of this product without notice.

1 3

10. OSD MENU STRUCTURE

MAIN

MENU

L E N S

S H U T T E R

/ AGC

1st Sub

MENU

M A N U A L

A U T O

A U T O

M A N U A L

2nd Sub

MENU

T Y P E

M O D E

S P E E D

R E T U R N

H I G H L U M I N A N C E

L O W L U M I N A N C E

R E T U R N

M O D E

S H U T T E R

3rd Sub

MENU

D C

A U T O , O P E N , C L O S E

( 0 0 0 ~ 2 5 5 )

M O D E

B R I G H T N E S S

M O D E

B R I G H T N E S S

S H U T + A G C

1/50(PAL),1/100(NTSC)

1/60(NTSC),1/120(PAL)

1/250,1/500,1/1000

1/2000,1/4000,1/10000

6 , 1 2 , 1 8 , 2 4 , 3 0 , 3 6 , 4 2 , 4 4 . 8

W H I T E

B A L

A T W

P U S H

U S E R 1

U S E R 2

A G C

R E T U R N

S P E E D

D E L A Y C N T

A T W F R A M E

E N V I R O N M E N T

R E T U R N

B - G A I N

R - G A I N

R E T U R N

B - G A I N

R - G A I N

R E T U R N

( 0 0 0 ~ 2 5 5 )

( 0 0 0 ~ 2 5 5 ) x0.50,x1.00,x1.50,x2.00

I N D O O R , O U T D O O R

( 0 0 0 ~ 2 5 5 )

( 0 0 0 ~ 2 5 5 )

( 0 0 0 ~ 2 5 5 )

( 0 0 0 ~ 2 5 5 )

A N T I C R

M A N U A L

L E V E L

R E T U R N

2 4 ~ 1 0 3

P U S H L O C K

BACK LIGHT O F F , B L C , H L C

M I R R O R

B R I G H T N E S S

C O N T R A S T

P I C

ADJUST

S H A R P N E S S

H U E

G A I N

R E T U R N

O F F , O N

( 0 0 0 ~ 2 5 5 )

( 0 0 0 ~ 2 5 5 )

( 0 0 0 ~ 2 5 5 )

( 0 0 0 ~ 2 5 5 )

( 0 0 0 ~ 2 5 5 )

A T R

O N

L U M I N A N C E

C O N T R A S T

R E T U R N

L O W , M I D , H I G H

LOW,MIDLOW,MID,MIDHIGH,HIGH

O F F

4th Sub

MENU

SHUT,AUTO IRIS, SHUT+AUTO IRIS

( 0 0 0 ~ 2 5 5 )

A G C , O F F x0.25,x0.50,x0.75,x1.00

*

SHUT+IRIS

: Both the Shutter and the Mechanical Iris are automatically adjusted according to brightness.

*

Auto Iris(Default)

: The Shutter stays at the manually selected value and only the Mechanical Iris adjusts to brightness.

1 4

10. OSD MENU STRUCTURE

MAIN

MENU

1st Sub

MENU

2nd Sub

MENU

D E T E C T S E N S E

B L O C K D I S P

M O N I T O R A R E A

( 0 0 0 ~ 1 2 7 )

3rd Sub

MENU

M O T I O N

D E T

O N

A R E A S E L

OFF,ON,ENABLE (CONTROLER)

O N , O F F

1/4, 2/4, 3/4, 4/4

T O P

B O T T O M

L E F T

R I G H T

R E T U R N

O F F

N E X T

E X I T

S A V E A L L

P R I V A C Y

N R

C A M E R A

I D

4th Sub

MENU

NTSC:(000 ~ 244) / PAL: (000 ~ 288)

NTSC:(000 ~ 244) / PAL: (000 ~ 288)

NTSC:(000 ~ 474) / PAL: (000 ~ 468)

NTSC:(000 ~ 474) / PAL: (000 ~ 468)

1/4, 2/4, 3/4, 4/4

O N

A R E A S E L

T O P

B O T T O M

L E F T

R I G H T

( 1 ~ 8 )

0 . 0 0 , 0 . 5 0 , 0 . 7 5 , 1 . 0 0

NTSC:(000 ~ 244) / PAL: (000 ~ 288)

NTSC:(000 ~ 244) / PAL: (000 ~ 288)

NTSC:(000 ~ 474) / PAL: (000 ~ 468)

NTSC:(000 ~ 474) / PAL: (000 ~ 468)

C O L O R

T R A N S P

M O S A I C O F F , O N

R E T U R N

O F F

N R M O D E

C L E V E L

OFF,Y,C,Y/C

( 0 0 0 ~ 0 1 5 )

( 0 0 0 ~ 0 1 5 ) Y L E V E L

R E T U R N

O N E D I T M O D E

R E T U R N

O F F

E N G L I S H , 日 本 語 , D E U T S C H , F R A N C A I S ,

Русский,

P O R T U G U Ê S , E S P A Ñ O L , 中 文 LANGUAGE

CAMERA

RESET

BACK

EXIT

SAVE ALL

* I m p o r t a n t N o t e :

- Any changes made to the camera settings must be saved prior to exiting the OSD menu.

E l s e a l l c h a n g e s w i l l b e d i s c a r d e d .

- B y c h a n g i n g t h e l e n s o p t i o n i n t h e O S D f r o m M A N U A L t o A U T O w i l l a u t o m a t i c a l l y c h a n g e t h e

SHUTTER/AGC setting from AUTO IRIS to SHUT+AUTO IRIS.(Default:AUTO IRIS)

1 5