Robomow RC306 lawnmower Operating instructions

Add to my manuals
50 Pages

advertisement

Robomow RC306 lawnmower Operating instructions | Manualzz

Original Operating Instructions (EN)

Robotic Mower

RC302 / RC304 / RC306

TC150 / TC300 / TC500

MC150 / MC300 / MC500

Operating Manual

Table of Contents

Chapter 1 – Introduction and Safety………………………………………………………………… 3

1.1 Introduction…………………………………...……………………………………………… 3

1.2 Warnings Decal Definitions ……………………………………………………….…….… 4

1.3 Safety Warnings & Precautions ……………………………………………………….….

4

1.4 Robomow  Safety Features …………………………………………………………....

6

Chapter 2 – Know Your Robomow  ………………………………..……………...…………...….

7

2.1 What’s in the Box.......................………………...…………….…………………………… 7

2.2 How Robomow Works For You……………………………………………………….…….… 8

2.3 Operation Method……………….……………………………………………………….….

9

Chapter 3 – Planning Ahead………………………………………………………………………….. 10

3.1 Lawn Types: What does your lawn look like?………………………….………………… 10

3.2 Select Base Station Location …………………………….………………………….…….

12

3.3 Select Power Box Location………………………………………...…….………………… 14

3.4 Planning the Perimeter Wire’s Layout………………………………….………………… 14

3.4.1 Objects inside lawn ………………………………………………..…………………… 14

3.4.2 Slopes ………………………………………………………………….………………..

15

3.4.2 Distances from the Edge………………………………………………………….

………… 15

Chapter 4 – Initial Setup …………………………………..………………………………………….. 16

4.1 Preparations …………………………………………………………………………….….

16

4.2 Perimeter Wire Setup ………………………………………………..…………………….

16

4.3 Perimeter Wire within the Working Area ……………………….…………………….….

19

4.4 Fastening Perimeter Wire to the Ground ……………………………..………………….

21

4.5 Back at the Base Station – Completing the Perimeter Wire Setup ……………….….

22

4.6 Placement and connection of the Base Station …………………..…………………….

22

4.7 Installing the Power Box…………………………………………………..…………….….

23

4.8 Setup in None-Base Zone.…………………………………………..…………………….

24

Chapter 5 – Preparing Robomow ……………………………………...……………………………. 27

5.1 Adjust the Cutting Height …………………………………………………………………..

27

5.2 One-time Setup (Step By Step)……………………………………….…………………...

27

Chapter 6 – Operation………………………………………………………………………..………... 30

6.1 Automatic Operation …………………………………………………..…………………… 30

6.2 Operating Panel ……………………………………………………………..……………...

30

6.3 Manual Operation………………………………………………………………….………... 31

6.4 Menu Options ………………………………………………………..……………………...

32

6.5 Operation in a Non-Base Zone……………………………………..……………………...

35

Chapter 7 – Using the Power Box ……………………………………………..…………………… 36

Chapter 8 – Charging …………………………………………………………..…………...………… 37

Chapter 9 – Troubleshooting and User Messages …………………………………....………… 37

Chapter 10 – Specification …………………………………..………………………………..……… 43

Chapter 11 – Maintenance and Storage …………………..………………………………..……… 44

11.1 General Instructions …………………………………….…………….…………………..

44

11.2 Battery Maintenance and Disposal ………………………………….…………………..

44

11.3 Winter Storage and Service ……………………………….….………………..………..

44

11.4 Maintenance of the Mowing Deck ………………………………….….………………..

44

11.5 Maintenance of the Blade ………………………………………..….………………...… 45

11.6 Splicing the Perimeter Wire ………………………………………….…………………... 46

11.7 Maintenance of the Base Station Area …………………………………….…………...

46

11.8 Lightning storm ………………………………………………….……………….….…….

46

Chapter 12 – Accessories …………………..………………………………………….……..……… 47

Chapter 13 – Tips for maintaining your lawn ……………………………………….……..……… 48

Warranty Card …………………..………………………………………………………..……..……… 49

1. Introduction And Safety

EC Declaration of Conformity

Manufacturer: F. Robotics Acquisitions Ltd.

Hatzabar St., Industrial Zone

P.O.Box 1412 Pardesiya,

42815 Israel

The products covered by this Declaration

26 Volt Battery operated Robotic Lawn Mower model:

Robomow RC 302/34/306 MC 150/300/500 and

TC 150/300/500 (with Base Station)

F. Robotics Acquisitions Ltd. declares under sole responsibility that the products identified above conform to the Directives below:

- Machinery Directive 2006/42/EC

Standards referenced: EN ISO 12100:2010.

- EMC Directive 2004/108/EC

Standards referenced: EN 55014-1:2011. EN 55014-2:2008. EN 61000-3-2:2006. EN 61000-3-3:2008.

- Noise Directive 2000/14/EC

Standards referenced: BS EN ISO 3744:2010. ISO 11094:1991.

- RoHS Directive 2011/65/EU.

Technical file representative:

Mr. Gerome De Schutter Friendly Robotics BV.

Address: Expeditieweg 4-6, Andelst 6673, Netherlands.

I hereby declare that the above product conforms to the requirements as specified above

Shai Abramson – Senior VP R&D

F. Robotics Acquisitions Ltd.

Israel

26 November 2013

1.1 Introduction

The products are manufactured by F. Robotics Acquisitions (Friendly Robotics).

© Friendly Robotics, 2014-A. All rights reserved. No part of this document may be photocopied, reproduced, electronically transmitted or translated without the prior written consent of Friendly Robotics.

Product, product specifications and this document are subject to change without notice. All other trademarks are property of their respective owners.

Welcome to the world of home robotics with the Friendly Robotics Robomow!

Thank you for purchasing our product. We know that you will enjoy the extra free time you will have while using Robomow to mow your lawn. When set up and used properly, Robomow will operate safely on your lawn and provide you with a quality of cut matched by a few mowers of any kind. You will be impressed with your lawn’s appearance and best of all,

Robomow did it for you.

IMPORTANT!

The following pages contain important safety and operating instructions. Please read and follow all instructions in this manual. Carefully read and review all safety instructions, warnings and cautions contained in this manual.

Failure to read and follow these instructions, warnings and cautionary statements may result in severe injury or death to persons and pets or damage to personal property.

3

1.2 Warning Decal Definitions

These are the symbols on Robomow  ; Read them carefully before operating Robomow  .

1 2 3 4 5 6 7

1. This is a dangerous power tool. Use care when operating and follow all safety instructions and warnings.

2. Read through the Operating & Safety Manual carefully before operating your Robomow  .

3. Hazard of throwing or flying objects while in operation.

4. Keep a safe distance from Robomow  when operating. Keep people in particular children, pets and bystanders away from the area in which Robomow  is being used.

5. Severing of toes or fingers – Rotary mower blade. Risk of injury from rotating cutting blade. Keep hands and feet away and do not attempt to lift Robomow  from this area.

6. Operate the disabling device before working on or lifting Robomow  .

7. Do not ride on Robomow  .

Do not dispose Robomow  or any other part of it as unsorted municipal waste –

It should be collected separately.

This product conforms to the applicable EU Directives

1.3 Safety Warnings & Precautions

Training -

1. Read this Operating and Safety Manual carefully before operating Robomow  . Be familiar with the controls and the proper use of Robomow  .

2. Never allow people unfamiliar with these instructions or children to use Robomow  .

3. The operator or user is responsible for accidents or hazards occurring to other people or their property.

Preparation -

1. Ensure the correct installation of the Perimeter Wire system as instructed.

2. Periodically inspect the area where Robomow  is to be used and remove all stones, sticks, wires, bones, and other foreign objects.

3. Periodically visually inspect to see that the blade are not worn or damaged. Replace worn or damaged blade in sets to preserve balance.

Operation -

1. Do not operate Robomow  if any safety feature or any part is damaged, worn or inoperable.

2. Keep hands and feet away from the cutting blade and other moving parts.

3. Never pick up or carry Robomow  while the motors are running.

4. Do not leave Robomow  to operate unattended if you know that there are pets, children or people in the vicinity.

5. Never mow while people, especially children, or pets are nearby.

6. Always switch off the Safety Switch before lifting the mower or attempting any adjustments.

7. Do not to touch the blade before the blade have come to a complete stop.

8. Do not use Robomow  for any purpose other than for which it is intended.

9. Keep all guards, shields, safety devices, and sensors in place. Repair or replace damaged parts, including decals.

10. Never pick up or carry Robomow® while the motors are running.

4

Transport –

To safely move from or within the working area:

1. Press the STOP button to stop Robomow  .

2. Use the Remote Control (available as an accessory) to drive it from place to place.

3. In case of different height level, switch off the Safety Switch, and carry the mower by the carrying handle.

4. In case of long transportation, use the original packaging.

5. When transporting Robomow  over long distances switch off the Safety Switch.

IMPORTANT! After turning off the Safety Switch always reset the current day and time. Failure to do so may result in non-intentional operation of the Robomow.

Using Remote Control (Manual Mowing)

1. Mow only in daylight or in a good artificial light and avoid operating in wet grass.

2. Do not operate Robomow  when barefoot or wearing open sandals. Always wear substantial footwear and long trousers; Always be sure of your footing on slopes.

3. Use extreme caution when reversing the mower towards you.

4. Always switch on the motor according to instructions with feet well away from the blade.

5. Do not mow manually in slope greater than 15 degrees or where a firm footing is not possible.

Maintenance and Special Instructions–

1. Always switch off the Safety Switch of Robomow  before clearing blockage/ checking/ cleaning/ working on

Robomow  or replacing the blade. Never attempt to service or adjust the mower while it is in operation.

2. In case of abnormal vibrations, stop the mower, switch off the Safety Switch and check for any damage of the blade. Replace worn or damaged blade to preserve balance. If vibration continues, call for service.

3. Use heavy gloves when inspecting or servicing the blade.

4. Do not perform maintenance when barefoot or wearing open sandals. Always wear suitable work shoes and long trousers;

5. Replace worn or damaged parts for safety.

6. Use only the original equipment and accessories. It is not permitted to modify the original design of Robomow  .

All modifications are made at your own risk.

7. Maintenance/ Servicing / Cleaning of Robomow  should be according to manufacturer’s instructions.

8. Keep all nuts, bolts and screws tight to be sure the machine is in safe working condition.

9. Warning! When there is a risk of a lightning storm, disconnect the Perimeter Wire from the Base Station / Perimeter

Switch and the Power Box 230V/120V plug from the power outlet.

Batteries

1. Do not open or mutilate the battery pack.

2. The battery pack should be replaced by a service dealer only.

3. The Battery Pack contains electrolytes. In case of an electrolyte leakage from the battery pack, the actions described below are required:

- Skin contact: Wash the contact areas off immediately with plenty of water and soap.

- Eye contact: Flush the eyes with plenty of clean water for at least 15 minutes immediately, without rubbing.

- Get medical treatment.

4. Ensure that the battery pack is charged using the correct charger recommended by the manufacturer. Incorrect use may result in electric shock, overheating or leakage of corrosive liquid from the battery.

Product End of Use -

1. Robomow and its accessories should be collected separately at the end of their life to prevent waste electrical and electronic equipment from ending up in landfill sites, to promote the reuse, treatment and recovery of electrical and electronic equipment with the purpose to preserve, protect and improve the quality of the environment, protect human health and utilize natural resources prudently and rationally.

2. Do not dispose of Robomow or any other part of it (including the Power Box, Base Station and Perimeter Switch) as unsorted municipal waste – it should be collected separately.

3. Ask your local distributor/dealer about return and collection systems available.

4. Do not dispose of the battery pack in a fire and do not place used batteries in your household trash.

5. The battery must be collected, recycled, or disposed of in an environmentally sound manner.

5

1.4 Robomow Safety Features

1. Child Lock

The Child Lock prevents unintended operation of Robomow  by an accidental press of one of the buttons. Only pressing of two buttons in a certain order will initiate the operation.

2. Anti-Theft / Safety Guard

The Anti-Theft system provides the user a disabling function that will prevent anyone from using or driving the Robomow personal security code.

 unless they have the valid code to enter. You will be prompted to enter a four digit code of your choice to use as your

3. Lift Sensor

In the event the mower is raised from the ground during blade operation, the blade will stop rotating immediately.

4. Tilt Sensor

In case the mower is tilted up towards a vertical position, the blade will stop immediately.

5. Obstruction Sensor

Robomow detects when there is an obstacle in its way during operation. When the mower collides with an obstacle, the mower will stop the rotation of the blade immediately, will stop movement in that direction and reverse itself away from the obstacle.

6. Emergency Stop Button

Pressing the STOP button at any time during operation will stop the mower and the blade immediately.

7. Safety Switch

Switching off the Safety Switch will prevent any operation of the Robomow 

Robomow  and before any maintenance is done.

. It is required to switch it off before lifting

8. Sealed Batteries

The batteries that operate the Robomow  position.

are completely sealed and will not leak any type of fluids, regardless of

9. Base Station / Perimeter Switch and Perimeter Wire

Robomow  cannot operate without a Perimeter Wire installed and activated through the Base Station / Perimeter

Switch. In the event the Perimeter Switch is turned off or otherwise fails to function, Robomow  will stop operating.

6

2. Know Your Robomow

2.1 What’s in the Box

1

2 3

11

9

Models with a Base Station

10

12

13

4

Operating & Safety Manual

5

DVD

6

7 8

14

Models without a Base Station

1 Robomow®

2

3

Wire Pegs

Used for securing the wire to the ground.

Perimeter Wire

Used to create a virtual wall for your Robomow

4 Operating & Safety Manual

5

DVD

Setup and Operation Video.

6

7

RoboRuler

Used for setting the distance of the Perimeter Wire from the lawn edge.

Wire Connectors

Used for splicing wires (as needed)

8

9

Plot Connectors

Used for connecting the Perimeter Wire to the Base Station

Base Station

Used by Robomow to dock and charge when it is not mowing.

12

13

14

15 meters (50 ft.), (Low voltage cable

)

Power Box

Used to deactivate (halt) the automatic operation mode and reactivate it as needed. Also provides indication of Robomow’s status (Docking or Operating) and the

Perimeter Wire’s health.

Power Box Mount

Used for fixing the Power Box to a wall (including Screws and dowels).

Perimeter Switch

(incl. Power Supply and Stake)

Used to generate the signal in a Non-Base zone. The

Perimeter Switch comes with models which are not supplied a Base Station and is available as an accessory.

7

2.2 How Robomow Works for You

Perform a One-Time Setup before operating Robomow for the first time.

[Detailed instructions are in the following chapters]

• Install a wire around the entire lawn and around protected areas within the lawn area.

• The Perimeter Wire sets the boundaries for Robomow.

The Perimeter Wire is laid around the edges of the lawn and around trees, plants, ponds and objects that you want to prevent Robomow to run into.

• If the supplied wire is not sufficient, more wire can be purchased and spliced with a supplied connector to the existing wire.

• Small pegs are used to fasten the Perimeter Wire into the ground, below grass level.

• The Perimeter Wire will gradually disappear under the growth of new grass until it will be invisible.

Perimiter Wire

Peg

• You will place a Base Station along the Perimeter Wire. They perform two basic functions:

- Generate a signal along the Perimeter Wire.

- Charge Robomow’s batteries.

• The Power Box is connected between the Base Station and a

230V wall socket, using a 15m long low voltage cable.

• After having completed the installation of the Perimeter Wire, Base Station, and the Power Box, and performing the One-Time Setup, Robomow will do all the mowing for you for the entire season!

• Robomow is a robotic lawn mower that is powered by a maintenance-free battery. It leaves its Base Station at the scheduled mowing time. Robomow mows the lawn and then drives back to the Base Station to be charged and ready for its next scheduled mowing.

• As soon as Robomow leaves for mowing, the Base Station automatically triggers a special signal. This signal creates a virtual wall, visible only to Robomow. This signal keeps Robomow within the lawn boundaries, and prevents it from entering areas it was programmed to skip or protect.

Base Station and Power Box:

- Generates signal along the wire.

- Charges Robomow’s battery.

Large trees: Robomow is allowed to bump into them. at this size, the objects do not require a Perimeter Wire around them

Robomow detects the signal and changes direction as it reaches the wire

Perimeter wire as a virtual wall,visible only to Robomow requires a wire around it.

8

2.3 Operation Method

• Robomow is a robotic lawnmower designed to mow and maintain your lawn completely by itself.

Simple One-Time Setup - Robomow requires a simple one time setup, which can easily be done by the consumer. Robomow recognizes the wire using special sensors, and makes sure it always stays inside the designated area. Essential accessories are supplied with the product.

• Working Method –

- Robomow will automatically mow the lawn. It continuously alternates between mowing and charging.

- It independently leaves the Base Station and cuts the lawn.

- Edge Cutting - Unlike other robotic lawn mowers, Robomow is the only robotic mower that has a special Edge mode, in which it follows the perimeter wire for complete coverage of the lawn edges. Robomow is the only robotic mower to cut outside the wheels.

- Search the Base Station - Robomow starts to search for the Base Station when the battery capacity becomes too low. It does not mow when it is searching for the

Base Station.

- Robomow will then recharge and proceed mowing as needed. It will continue in mowing until completing the required mowing time for your lawn (based on the area you have set).

- When completing the mowing of the entire area (Mowing Cycle), Robomow will stay in the Base Station until the next Mowing Cycle will start.

- Robomow completes two Mowing Cycles per week in order to keep your lawn healthy and good looking. However if your lawn requires more time to maintain your lawn, you can easily adjust the time Robomow runs in a single Mowing Cycle.

- The Operating Panel on the top of Robomow is where you manage the mower and operating settings.

- Strong Cutting System - Robomow’s extra sharp blade enables to perform the first cut of the season, when the grass is relatively high.

- Availability - The mowing width of Robomow (28cm) and the powerful cutting system help Robomow to finish the job very fast and leave your lawn free for the family to enjoy.

LAWN FREE

TO ENJOY

A Remote Control is available as an accessory and is used for driving Robomow to a separated zone, if necessary. It is also used for mowing small patches of grass that cannot be reached in automatic operation.

Grasscycling - Robomow cuts the grass into very small clippings that are buried in the roots of the lawn, where they decompose and act like a natural fertilizer. Grass clippings contain 80-85% water and release valuable nutrients that return back into the soil. It is the natural recycling of grass.

Robomow App – Enables user friendly and intuitive operation of your

Robomow and opens more menu options and features, which are not available through the mower Operating Panel. The Robomow App can be downloaded from the Apps Store.

Robomow App is compatible with Smartphones/ Tablets that use one of the following Operating Systems: Android (Google) or iOS (Apple).

3G

12

9:41 AM

100%

SCAN HOME

EDGE &

SCAN

The mobile device has to include

Bluetooth Low Energy (BLE) branded as Bluetooth SMART.

STOP

The following mobile devices include BLE: o Samsung Galaxy SIII, Galaxy S4 and

Note II.

04:26

Scanning o Apple’s iPhone 4S, iPhone 5, iPad (3rd

& 4th generation), iPad Mini and others.

o HTC One, One X+ and Droid DNA

To download the Robomow App, use your mobile device to scan the QR code on the right, or download it from the App Store.

9

3. Planning Ahead

Getting your lawn ready for Robomow is rather simple.

Still, as each lawn is unique, we recommend to read this chapter before starting to install the perimeter wire. Planning the wire route and drawing a sketch of the lawn, including all obstacles and Base Station location, will make it easier and will prevent mistakes during the setup.

Please watch the setup video on the Robomow DVD. This Video will walk you through the complete setup process.

Please complete reading this “Planning Ahead” chapter before you start the setup. It will guide you in finding the best locations for the Base Station, Power Box, and for the Perimeter Wire.

The Perimeter Wire functions as an “invisible wall” for Robomow. It sets the boundaries of lawn zones and it surrounds specific areas where you do not want Robomow to enter. The Perimeter Wire is held to the ground with small pegs, supplied with Robomow. Soon after settling, the wire will become invisible under the growth of new grass.

As soon as Robomow starts operating, it turns on a signal that runs along the Perimeter Wire. This signal keeps

Robomow within its working zones and away from preset demarcated areas.

3.1 Lawn Types: What does your lawn look like?

There are 3 basic types of lawns: Some lawns are combinations of more than one type.

Your first task is to determine which type is yours.

Note – if you have purchased Robomow model without a Base

Station, then your zones should be defined as ‘Separated Zone’

(refer to Paragraph 3.2.3, 4.8 and 6.5) o Main Zone Only

Robomow will simply mow this lawn within its set boundaries.

o Main Zone + Sub-Zone(s)

Robomow will mow the Main Zone and will move automatically to the Sub-Zone(s).

IMPORTANT! Setting and Operation of a Sub-Zone can only be done and controlled using the Robomow App.

o Separated Zone

Robomow will mow each zone separately. Its movement between zones is restricted. Thus, you will have to bring the mower from the Main Zone to the Separated Zone every time you want to mow it.

Main Zone

Main Zone

Main Zone

Sub Zone

Separated-Zone

3.1.1 “Main Zone Only” Type Lawn

The “Main Zone Only” lawn consists of one whole area.

It has no Sub- Zones and no Separated Zones.

If you answer “yes” to the all of the following questions, your lawn is a “Main Zone Only” type lawn: o Is your grass area one continuous zone?

And: o Are all areas of your lawn wide enough for

Robomow to navigate through effectively? (Min.

3 meters (10 ft.) wide at its narrowest point).

At least 3 meters

(10 ft.) wide

Main Zone Only

10

If your lawn does not match this description, read the next Sections to find the style of your lawn.

If your lawn is “Main Zone Only”, you can skip to Section 3.3 of this chapter to determine the Base Station location.

3.1.2 “Main Zone + Sub-Zone(s)“ Type Lawn

If your lawn contains a Sub-Zone as defined in this section, then you MUST download the Robomow App in order to mow it effectively in automatic mode from the Base Station, otherwise you have to set it as a

Separated Zone as defined in section 3.2.3 below. The Robomow App can be downloaded from the App

Store. For more details about the Robomow App and its compatibility with your Smartphone/Tablet, please refer to Paragraph 2.2 – Operation Method.

This type of lawn consists of more than one zone and these zones are connected by a narrow pass.

In this type of lawn, Robomow will be able to drive from one zone to the other in order to mow the whole area.

If you answer “yes” to all of the following questions, your lawn is a “Main Zone + Sub-

Zone” type lawn:

Main Zone

Main Zone

Sub-Zone

Main + Sub-Zone with a Narrow Pass

o Is your grass area one continuous area?

o Are parts of your lawn separated from the Main Zone?

o Is there a Narrow Pass of min 1m (3.3 ft) for Robomow to drive through between these zones?

o Is this Narrow Pass firm, level and smooth (not stony, sandy or elevated)?

For example: grass area, sidewalk, firm path, solid ground.

Such additional areas are called Sub-Zones.

To enable setup and control of Sub-Zone(s), download the Robomow App to your Smartphone or Tablet.

Defining Sub-Zone(s) will enable Robomow to drive through the Narrow Pass in order to get to a Sub-Zone and to mow both the Main Zone and its Sub-Zone(s) one zone at a time.

If your lawn does not match this description, skip to the next Section 3.2.3 of this chapter: “Separate Zones”

3.1.3 “Separated Zones” Type Lawn

If your lawn contains a Separated Zone as defined in this section , refer to Section 6.4.2 (Add Separated Zone

- number p014 in the table).

“Separated Zones” type lawn consists of two or more zones that are not connected. Robomow cannot drive between these zones.

If you answer “yes” to at least one of the following questions, your lawn is of the “Separated Zones” type.

o Are parts of your lawn separated by fences, sidewalks, or other objects that

Robomow cannot pass?

Or o Are parts of your lawn separated by a gravel path or similar material that may damage the mower blade?

Or o Are the zones of your lawns joined by a pass too narrow for Robomow to drive through: less than 1m (3.3 ft.) in width?

Or o Are the zones of your lawn situated at lower or higher level?

If your lawn does not fit any of these descriptions, it is probably either a “Main Zone Only” or “Main Zone

+Sub- Zone” type. Skip to Section 3.3 – Select Base Station and Power Box Location

 A lawn may consist of up to 2 Separated Zones.

 The mower must be carried or driven to this area manually.

 Any of the 3 types can be in a combination of more than one type of lawn.

.

11

Types of Separated Zone setups:

A Separated Zone smaller than 100 m² (1100 ft²)

o Separated area that is smaller than 100m² (1100 ft²) can be covered in a single operation, thus, if possible, the separated area may be connected to the main area’s Perimeter Wire

(have the signal come from the

Main Base Station).

Or o It may have to have its own separate Perimeter Wire.

In that case, it will have to be connected to a Perimeter

Switch (optional accessory – see Chapter 12 - Accessories).

Base Station

Separated Zone Smaller than 100m 2 (1100ft 2 )

Or:

A Separated Zone larger than 100 m² (1100 ft²)

o If a separated area is larger than

100m² (1100 ft²), then it requires more than a single operation to cover the area; o In such cases, an additional

Base Station (optional accessory) should be installed in the

Separated Zone, otherwise you will have to manually bring the mower several times to the

Separated Zone in order to complete the mowing of the area.

Separated Zone Smaller than 100m 2 (1100ft 2 )

3.2 Select Base Station Location

3.2.1 Base Station Location Guidelines

place the Base Station within

3 meters (10 ft.) after a corner (relevant for Internal setup only (section 3.3.2).

The Base Station should be within 15m (50 ft.) of a power outlet (230V / 120V).

If the lawn has more than one zone, place the Base

Station within the largest zone.

Make the Base Station invisible to the street to avoid theft.

Place the Base Station on a relatively level ground.

Do not place it on a slope.

12

There are two options to set the Base Station:

3.2.2 Internal Setup (on the lawn perimeter)

Choose a place along the Perimeter Wire where you want to place the Base Station, based on the inputs given in paragraph 3.3.1.

Place the Base Station in the direction shown in the figure to the right.

3.2.3 External Setup (off the lawn perimeter):

There are two types of External Setup:

A. At a corner

In this type of setup, the Base Station is located at one

of the corners of the lawn, as shown in the figure at the right.

corner where you want to place the Base

Station outside of the lawn area.

Place the Base Station, where its front side is touching the lawn edge or placed somewhat on the lawn.

Continue to lay the perimeter wire as shown in the figure to the right, where it continues at least 10cm beyond the Base Station and turns back towards the lawn at a distance of 10cm from the other wire.

The Base Station may be placed in a small shift to the right in order to allow smooth entry of the mower to the Base Station.

You will have the opportunity to later adjust the Base

Station position to confirm smooth entry.

B. Outside the lawn

(Can be set only through the Robomow App for specific models)

• Choose a place outside the lawn where you want

Robomow to dock and charge.

• Confirm the path between the lawn and the outside area is smooth with no height difference, so

Robomow will not get stuck and will follow the wire smoothly.

• The surface between the lawn and the Base Station should be hard (such as a sidewalk or rigid ground) and not sandy or stony, so Robomow will not slip or get stuck on it.

• The area between the lawn and the Base Station should be clear of obstacles and objects.

• Lay the wire as shown in the figure to the right:

- Narrow path of 50cm width.

- Square Perimeter Island of 30 cm edges.

- Island starts 50cm from the Perimeter Wire.

- Keep a distance of 10cm between Perimeter Wire and the Island from both sides.

- The front of the Base Station should be placed a minimum distance of 1.5m (5 ft) from the Perimeter

Wire and NOT more than 4m (13 ft).

10cm (4”)

Min. 10cm (4”)

Perimeter Island

30 cm

10cm (4”)

Main Zone

Min. 1.5m (5ft) - Max 4m (13ft)

50 cm (20”)

10cm (4”)

50 cm (20”)

13

3.3 Select Power Box Location

Consider the following in order to select the Power Box location:

 The Power Box will be connected to the Base

Station using the 15m (50ft.) Extension Cable.

 Select a suitable location for the Power Box to be mounted on a wall near a power outlet.

 Locate it outside the lawn perimeter.

 Select an easily accessed spot.

 Select a dry and sheltered location.

 The Power Box is to be mounted vertically.

Power Bow fixed to the wall

15m (50ft) Extension

Cable (low voltage)

The Power Box is suitable for Outdoor use. Yet, it should be placed in a sheltered, dry and well ventilated spot. The Power Box should not be exposed to direct sunlight or rain.

3.4 Planning the Perimeter Wire Layout

3.4.1 Objects inside lawn

 Objects such as flower beds, ponds, or small trees can be protected by designating “ Perimeter Islands”, which are demarcated areas of the lawn, where

Robomow does not enter.

 If the areas where obstacles are grouped closely together, they should be demarcated by a single, continuous Perimeter Island.

 Obstacles that are vertical, relatively rigid, and higher than 15 cm (6 inches), such as trees, phone or power poles, do not need Perimeter Island. Robomow will turn when it collides with these obstacles.

3.4.2 Slopes

Slope on the perimeter

 The Perimeter Wire can be laid across a slope that slants less than 10% (10cm rise per 1m).

CAUTION! If the Perimeter Wire is laid across a slope steeper than10%, there is a risk that the mower will slip and cross outside the wire, especially when the grass is wet’.

However, if there is a barrier (e.g. fence or wall) that can protect the mower from slipping off, the

Perimeter Wire can be set on that slope.

Perimeter Slope

Max. 10%

14

Slope inside the lawn

 Robomow can mow areas inside the working area with a slope of up to 35% (35cm rise per 1m).

 Tip: If the mower tilts off the ground while climbing a slope, it is too steep. Exclude this steep area from

Robomow’s cutting area.

In Lawn Slope 35%

How to calculate the slope of your lawn?

100cm (3.3ft)

Length

35cm (1.1ft)

Max 35% slope

How to calculate the slope of your lawn?

35cm (Elevation)

100cm (Length)

35% (slope)

3.4.3 Distances from the Edge (Pools, Ponds, Cliffs, etc.)

 RoboRuler is used to measure the distance from the edge, where the wire is to be placed.

 In certain cases, near bodies of water such as pools and ponds, or great height differences such as cliffs, it is required to maintain a greater distance from the Edge (see Section 4.2.2).

15

4. Initial Setup

4.1 Preparations

Recommendation before you start:

During setup, you will insert pegs into the ground. To complete this task smoothly, we recommend not to do it while the grass is high and to water it before starting.

4.1.1 Getting Ready

Make sure all parts needed for setup are within reach. Have the Robomow box nearby, so all items are available.

In addition, you will need the following tools: A hammer, small flat screwdriver, Phillips screwdriver, Combination Pliers.

Hammer

Small flat and Philips

Screwdrivers

Combination Piers

4.1.2 Installing the Power Box

Mount the metal bracket onto a vertical surface with the provided screws. Make sure the narrow part with the holes facing up as shown in the figure to the right.

• Place the Power Box above the metal bracket and slide it into place along the vertical surface.

• Connect the Power Box to a regular power outlet (230V

/ 120V).

4.1.3 Charging the battery before the first operation

You can charge the Robomow battery while running the setup of the Perimeter Wire. This will ensure that Robomow will be ready for operation when the setup is completed.

• The power of the mower is switched off when shipped from the factory. Press the ‘Settings’ button on the

Operating Panel for 3 seconds to awake the mower.

• Connect the DC Cable coming from the Power Box to the

Charging Socket at the rear side of Robomow.

• Confirm the Battery LED on Robomow is blinking, which is an indication of charging.

• Leave Robomow connected to the Power Box while completing the setup of the Perimeter Wire.

4.2 Perimeter Wire Setup

Before you start the setup, you should have a plan for the Perimeter Wire layout and for the location of the Base

Station. Your plan should consider the following: o What type of lawn areas does your lawn have?

(Main Zone Only / Main + Sub-Zones / Separated Zones / combination of types).

o Are there protected or excluded areas on the lawn? (Perimeter Islands).

o Are there any slopes that Robomow should avoid?

o Are there edges of pools, ponds, cliffs etc., that need an extra distance from the Perimeter Wire?

16

4.2.1 Starting Point: Perimeter Wire at the Base Station area.

• Place the Base Station, according to your plan, as shown in the figure to the right.

• Do not place the Base Station within 3m (10 ft.) of a corner

• Select the roll of wire with a green plot connector attached to the end.

• Pull the plot connector and some wire out of the plastic covering.

! Do not remove the spool of wire from its covering.

The plastic covering is the dispenser for the wire.

• Peg the beginning of the wire to the ground, where the Base

Station will be located. Pegs are supplied in the Robomow’s box.

• Pull out 30 cm (12 inches) of wire and leave it loose near the

Base Station location. Later, at the end of the setup, this part of the wire will close the Perimeter Wire loop.

• Start laying the wire in an anticlockwise direction.

• Continue to pull the Perimeter Wire out of its covering, laying it loosely as you walk along the lawn edge.

Perimeter Wire

Peg

! If you get to any area /object that needs care or special boundaries, make sure you carefully lay the

Perimeter Wire as needed. The next sections deal with such special cases.

4.2.2 Laying the Perimeter Wire

o The Perimeter Wire is secured to the ground by pegs supplied with Robomow. Initially insert pegs every few meters and at corners. At this early stage set a minimum number of pegs. Later, after testing the wire setup, you will insert all necessary pegs.

o After uncoiling some wire, before inserting pegs, use the RoboRuler to determine the distance of the wire from the lawn edge or obstacles.

• If the working area borders against a flat area, flower bed, small step (more than 1 cm), small ditch, or a small elevation (up to 5 cm), the Perimeter Wire should be laid 20 cm (8 inches) inside the working area. This prevents the wheels from driving into a ditch. Use the shorter distance of the RoboRuler to set the distance of the wire from the lawn edge.

• If the edge is sloped (max 10% is allowed) or is bordered with high obstacles such as a wall or fence, the Perimeter Wire should be laid at a distance of

28 cm (11 inches) from the obstacle. Use the longer distance of the RoboRuler to set the distance of the wire from a wall.

18cm (7”)

28cm from Wall (11”)

17

• If the working area borders against a flat path that lies level with the lawn, it is possible to allow

Robomow to run over the path. The Perimeter Wire should then be laid 10 cm (4 inches) from the edge of the path.

• When the working area is divided by a flat path that is level with the lawn, it is possible to allow

Robomow to run over the path. The Perimeter Wire can be laid under the pavement blocks or in the joint between them.

Important! The mower must never run over gravel, mulch, or similar material, which can cause the mower to slip and damage the blade.

IMPORTANT INFORMATION

If the working area is adjacent to a swimming pool, watercourse, slope greater than 10%, precipice higher than 50cm or a public road, the Perimeter Wire must be supplemented with a fence or the like. The height must then be at least 15 cm (6 inches). This will prevent the mower from ending up outside the working area under any circumstances.

If such a barrier exists, you may set the

Perimeter Wire 28 cm (11 inches) from the barrier.

If there is no fence or the like, then lay the

Perimeter Wire at minimum distance of 1.2m from the water.

18

o Maintain a 45° angle in all left-turn corners when laying the wire along the perimeter. It is not necessary to maintain 45° angle on right-turn corners along the perimeter. o Continue laying the wire, according to your plan.

Gradually pull the wire out of its dispenser and lay it loosely as you are moving in an anticlockwise direction.

90 o

Right turns

45 o

Left turns

20cm

4.3 Perimeter Wire within the Working Area

4.3.1 Hard Obstacles

o Obstacles that can withstand a collision, for example, trees or bushes higher than 15 cm, do not need to be demarcated by the Perimeter

Wire. Robomow will turn when it collides with this type of obstacle.

4.3.2 Perimeter Islands

o Use the Perimeter Wire to demarcate areas inside the working area by creating islands around obstacles that cannot withstand a collision, for example, flower beds and fountains.

o Continue uncoiling the wire, moving from the edge towards the protected object.

o Peg the Perimeter Wire around the protected object in a clockwise direction.

o Complete bordering the island and return to the spot where you left the lawn’s edge o The wires leading to the Island and from it should be parallel and touching.

Therefore, peg both wires, to and from the island, together with the same pegs.

o Robomow will not recognize these two wires. It will mow over them as if they do not exist.

o Robomow will recognize the single blocking wire around the Perimeter Island and will not enter this area.

2 Wires under same peg

Direction of setup:

Clockwise around

Min. distance between islands: 1m (3.3ft).

Otherwise,demarcate jointly as one island

CAUTION ! Setting the Perimeter Wire anticlockwise around the obstacle will cause the mower to drive into the island.

Keep the following distances when setting Perimeter Islands:

- The minimum distance of the Perimeter Wire from the protected area should be 28 cm (11 inches).

- If you need to protect a thin object, set the minimum radius of the Island to 35 cm (15 inches).

- Maintain a minimum of 1m (3.3 ft.) between adjacent islands.

- Maintain a minimum of 1m (3.3 ft.) between island wire and the Perimeter Wire.

- If protected objects are grouped closely together, demarcate them as a single Perimeter Island.

28cm

28cm

Min 1m

19

4.3.3 Setting a Narrow Pass

A Narrow Pass is defined as a path that connects two zones of the lawn. The path enables Robomow to drive between the zones while following the wire, but prevents the mower from crossing between them while mowing the inner area of the zones.

To set up a Narrow Pass follow the instructions given in the figure below:

A. At the point you want the mower to start driving towards the Sub-Zone start to set the Narrow Pass.

B. 50 cm (20 inches) from the Narrow

Pass entry, set a Perimeter Island

(refer to 4.2.4) of 30 cm sides (12 inches) at a distance of 10 cm (4 inches) from the Perimeter Wire.

C. Continue to lay the wire towards the

Sub-Zone and lay another Island with the same dimensions , 50 cm (20 inches) from the Sub-Zone Perimeter

Wire.

D. After completing the setup of the wire in the Sub-Zone, make sure you keep 10 cm (4 inches) between the wire and the islands on the way back to the Main Zone.

10cm

50cm

10cm

Perimeter Island

30x30cm

Perimeter Island

30x30cm

The above setup allows Robomow to drive along the wire to reach the Sub-Zone. However, while mowing each zone individually, it will not cross over to the other zone.

20

If the Narrow Pass is wider than 2m, and you want Robomow to mow the area inside the Narrow Pass, then you can set the wire as shown in the figure below. Such a setup allows the mower to mow inside the Narrow Pass while mowing the inner part of the lawn, but prevents it from crossing between the zones.

A. At the point you want the mower to start driving towards the Sub-Zone start to set the Narrow Pass.

B. Set an Island at the middle of the

Narrow Pass and keep a distance of 10 cm (4 inches) from the

Perimeter Wire.

C. The island dimensions should be

30 cm along the side and as wide as needed, keeping 10 cm from both sides.

D. After completing the setup of the wire in the Sub-Zone, make sure you keep 10 cm (4 inches) between the wire and the island on the way back to the Main Zone.

Perimeter

Island

As long as needed when keeping 10cm from both sides

10cm

4.4 Fastening Perimeter Wire to the Ground

o Before starting to lay the Perimeter Wire, it is recommended to cut the grass where the wire is to be laid.

It will then be easier to attach the wire to the ground. The risk that the mower will damage the wire during the operation is reduced.

o It is not necessary to bury the Perimeter Wire, though you may do so, up to 5 cm (2 inches) deep.

o Pull the wire tight while hammering the peg all the way into the ground.

WARNING !

Protect your eyes! Protect your hands!

Use proper eye protection and wear appropriate work gloves when hammering the pegs.

Hard or dry ground may cause pegs to break when driving them in.

o Use a hammer to insert the pegs into the ground.

o Insert the pegs at distances that will keep the wire down below the grass level and prevent the wire from becoming a tripping hazard (approximately 75 cm between pegs).

• The wire and the pegs will gradually become invisible under the growth of new grass. o If an additional wire is required in order to complete the setup, connect it using the water-proof wire connectors supplied with Robomow. (See Section

11.4 – Splicing the Perimeter Wire).

21

Use only the wire connectors supplied with Robomow.

Neither Twisted cables, nor a screw terminal insulated with insulation tape are a satisfactory splice.

Soil moisture will cause the conductors to oxidize, which will later cause a broken circuit.

4.5 Back at the Base Station – Completing the Perimeter Wire Setup

Once the Perimeter Wire loop is completed and pegged to the ground, complete the setup by attaching the beginning and the end of the Perimeter Wire to the Base Station Head.

o Hold both ends of the Perimeter Wire: the wire that started the loop is the one with an attached connector.

o Twist the two wires.

o Trim the end without the connector to make both of equal length. Remove any excess wire and strip back 5 mm (1/4 inches) of insulation from the wire end.

o Peg the two Perimeter Wires down to the ground using the same peg leaving enough loose wire. Twist together the two loose parts.

o Insert the end of the wire without the connector into the hole of the connector. Use a small flat screwdriver to tighten and secure this wire into the connector.

4.6 Placement and connection of the Base Station

o Place the Base Station on the Perimeter Wire as shown in the figure to the right.

o Align the center of the Base Station on the wire.

22

o Attach the Perimeter Wire connector to the Base Station

Head.

o After the Base Station has been positioned, insert

2 stakes into the Base Station holes as shown in the figure to the right. Only after the Base Station position will be tested, will you insert the 2 remaining stakes.

Laying and Fastening Extension Cable

Safety – Avoid injury!

The Extension Cable from the Power Box to the Base Station should be securely fastened to the ground! It should never present a tripping hazard.

The Extension Cable should cross ONLY over soft surfaces .

It should not cross over hard surfaces (e.g. Sidewalk, driveway) where it cannot be securely fastened.

o The 15m (50 ft.) Extension Cable is already attached to the Base Station Head, but if you need to disconnect it for any reason, remove the Base Station Head as shown in the figure to the right:

4.7 At the Power Box Location:

• Connect the DC Cable from the Power Box to the 15 m (50 ft.) Extension Cable.

• Connect the Power Box to a regular power outlet (230V / 120V).

• The Docking Indicator (1) will light up if the mower is in the Base Station.

• The Operating Indicator (3) will light up if the mower is not in the Base Station.

Docking Indicator On/Off Button

Operating Indicator Wire Indicator

23

4.8. Setup in a Non-Base Zone

A Non-Base Zone is an area of the lawn that is not connected to a Base Station.

A Perimeter Switch should be installed in these areas.

When necessary, the Perimeter Switch can be easily moved to other zones.

4.8.1 Determining the Perimeter Switch Location

Consider the following in order to install the Perimeter

Switch at an optimal location:

• The Perimeter Switch is to be installed outside the perimeter of the Non-Base Zone.

• Select a dry and sheltered location.

• The Perimeter Switch is to be mounted vertically.

• The Perimeter Switch is supplied with an indoor power supply. Choose a location close to a regular power outlet (230V / 120V).

Note – a rechargeable battery for the Perimeter Switch is available as an accessory (See Chapter 12 – Robomow

Accessories).

4.8.2 Perimeter Switch placing options

• The Perimeter Switch connector is easily connected and disconnected. It allows for quickly switching from one zone to another.

• You may use the large stake, attached to the back of the

Perimeter Switch, to easily insert it in and out of the ground.

The Perimeter Switch

MUST be Mounted vertically in order to maintain its’ water resistance

Wires leading from the lawn to the Perimeter

Switch are adjacent and touching.

• You may mount the Perimeter Switch on a vertical surface, such as a wall or deck railing. Use the three marks on the back of the Perimeter Switch cover.

4.8.3 Laying out the Perimeter Wire

The perimeter wire setup in a Base and Non-Base Zone are the same, except for the starting point:

• The Perimeter Switch is placed out of the area (at least

1 meter from the lawn).

• Start lay the Perimeter Wire from the Perimeter Switch location.

Min. 1m (3ft)

24

• Lay the Perimeter Wire from the Perimeter Switch to the lawn.

• Start laying the wire in anticlockwise direction.

• Once completing the Perimeter Wire loop, lay the wire back towards the Perimeter Switch.

• At the end of the Perimeter Wire loop, you have now two wires. Lay the two loose wires in the direction of the

Perimeter Switch location and peg them to the ground using a single peg for both.

4.8.4 At the Perimeter Switch’s location:

• Trim the ends of the loose wire to equal length and twist them together.

• Strip 5mm (0.2 inches) of insulation from the wire without the plot connector.

2 wires under the same peg

• Insert this wire end into the free hole in the connector and tighten the screws.

Small flat screwdriver

• Plug the perimeter wire connector into the Perimeter Switch.

25

• Hold the Perimeter Switch and squeeze its side tabs (1) to remove it from the back cover (2).

2

• Connect the Power Supply plug to the Perimeter Switch board. Replace the cover.

• Connect the power supply to a regular power outlet (230V

/ 120V).

!

IMPORTANT

!

The Power Supply is for indoor use ONLY.

Choose a sheltered, dry, and well ventilated location that is NOT exposed to direct sunlight, water, or rain.

• Press the ‘ON’ button on the Perimeter Switch.

A small flashing green light next to the ‘ON’ button indicates the system is on and functioning correctly.

The control panel has other indicators: a disconnected or broken Perimeter Wire and a poor splicing (connection) in the Perimeter Wire.

26

Flashing light indicates the system

Indicates a disconnected / broken wire

Indicates poor splicing of perimiter wires or perimiter wire. which is too long

The Perimeter Switch has an automatic shutoff feature. There is no need to turn it off after each use. The

Perimeter Switch will shut itself off after 12 hours of operation. You may manually turn it off by pressing the ON/

OFF button and holding it for 3 seconds. A beep will sound to indicate that the Perimeter Switch is off.

The Perimeter Switch can be operated by a rechargeable battery (available as an accessory).

1

5. Preparing Robomow

Before using Robomow for the first time, you have to perform some simple preliminary settings.

Once the preparations are complete, your Robomow will be ready to mow your lawn.

5.1 Adjust the Cutting Height

Blade Cutting Range: 20 – 60 mm (0.8 – 2.4 inches)

Safety Switch

To adjust the cutting height of the blade, do the following:

CAUTION! ALWAYS TURN THE SAFETY SWITCH OFF

BEFORE SERVICING BLADE!

• Lift the front side of the mower.

• Turn the knob while pushing it down.

• To raise the cutting height, turn anticlockwise.

• To lower the cutting height, turn clockwise

• The cutting height is displayed at the side of the mower.

5.2 One-Time Setup (Step by Step)

If the mower is in charging, remove it from the Base Station.

Otherwise press the ‘Settings’ button to wake the mower.

Make sure the Power Box is plugged in.

The mower is now ready to perform the One-Time Setup process.

5.2.1 Using the Operating Panel

Use the buttons on the Operating Panel as follows:

• Press the ‘Right’ or ‘Left’ arrows until your selection is displayed.

• Press OK to select the value shown on the display.

• Press ‘Back’ (STOP) to go back or to cancel.

Cutting height adjustment

LOW HIGH

ok

STOP

5.2.2 Choose Measurements Units and Formats

EU

US

Area / Distance

Meter

Foot

Temp.

Celsius

Fahrenheit

Clock

24 Hours

12 Hours

(AM / PM)

5.2.3 Set Day and Time

• Scroll to set the Day and press OK to confirm.

• Scroll to set the Time and press OK to confirm.

27

5.2.4 Main Zone Area

• Scroll to select an approximate area (EU- m² / US- ft²) of the Main Zone, where the Base Station is installed.

If an additional zone (Sub-Zone or Separated Zone) exists, do not include it in this area (it will be set separately).

Note – It is necessary to complete the above settings (5.2.1 –

5.2.3) in order to operate the mower. Every press on the

STOP button will change the screen one step back in the process.

5.2.5 Test Base Station Position

• After setting the area, U001 (Test Base Station Position) is displayed.

• Place Robomow inside the lawn, approximately 3 m (10 ft.) in front of the Base Station, facing the Perimeter Wire and press OK to start the test.

• Robomow drives towards the Base Station:

If the mower does not start the test, then one of the following messages will be displayed:

E3 (

No Wire Signal

)

Confirm that the Power

Box is connected to the power outlet and that the Extension Cable is connected at both ends, from the Power Box to the Base Station.

U029 (

Swap wires in plot connector

)

The

Perimeter Wire has been connected in the opposite direction. Swap the wires at the plot connector.

• Robomow will enter the Base Station, drive back, wait in front of the Base Station, and display U002 (

Peg Base

).

If U051

(

Reposition Base Station)

message is displayed:

• Move the Base Station slightly to align it with the Perimeter Wire.

• C heck for any obstacles that may interfere with the mower’s entrance to the Base

Station.

• While ‘ U002’ press OK.

(

Peg Base

) is displayed, insert the remaining

Stakes of the Base Station to secure it to the ground and

28

5.2.6 Test Wire Position

• U003 is displayed (

Test Wire Position

) – press OK .

• Robomow wll follow the wire along the edge to test the wire position.

Walk alongside Robomow while it is following the edge.

Having completed the process, Robomow will enter the

Base Station and the setup process is completed.

If the mower collides with obstacles along the edge, the mower will stop and drive backwards with ‘ U052 ’ (

Adjust Wire

) displayed:

• Move the wire slightly inward.

• Press OK to continue the Wire Test.

• If, at any point, you wish the mower to drive closer to the edge to enlarge the covered area, press Stop displayed -

Test Wire Position

):

(‘ U003 ’ is

- Move the wire slightly outward.

- Place the mower in front of the changed section of wire.

- Press OK to continue the ‘Test Wire Position’ process.

• If you want to quite the setup process, press the STOP button continuously for 3 seconds. The screen will change to the Main Display (current time).

• After completing the Test Wire Position, test the mower in Near Wire Follow mode to confirm it completes the drive near the wire smoothly, without acquiring any adjacent wire or hitting any obstacle on its way to the

Base Station.

• If the mower fails to complete the Near Wire Follow smoothly to the Base Station, then reduce the Near Wire

Follow Distance (Menu P004) and repeat the test until it will complete the drive smoothly.

5.2.7 After Setup is Completed

Once the wire setup is complete, drive additional pegs at a distance of approximately 0.75 m (2.5 ft.) apart.

• Use additional pegs in areas where there are bumps or dips in the lawn.

If needed, purchase extra pegs.

• Inspect the wire installation for tripping hazards.

29

6. Robomow Operation

6.1

Automatic Operation

o During the One-Time Setup, you have defined the size of your lawn. Robomow will automatically derive the required Mowing Time for your lawn.

o The One-Time Setup configures Robomow to perform automatically the following cycle of operations:

-

When the battery is fully charged Robomow departs from the Base Station.

-

Robomow mows the lawn.

-

It searches for the Base Station when the battery level gets low (Robomow doesn’t mow when it is searching for the Base Station).

-

It recharges the battery and gets ready for the next scheduled operation.

-

It continues mowing until it completes the required time for the lawn area (this is known as a Mowing

Cycle).

Note: Robomow mows the Edge only in the first mowing of each cycle. In the rest of the operations, Robomow mows the lawn without the Edge.

o

Robomow stays at the Base Station during the default Inactive Time (All day Sunday and nighttime daily

23:00 to 06:00). Inactive Time may be changed – see Section 6.4.1.3.

o

Mowing Time is derived from the set lawn Area.

Mowing Time may be changed using the Intensity menu – see Section 6.4.1.2.

o

Robomow mows the entire area Twice a week.

This frequency can be changed using the Interval menu – see Section 6.4.2 (p001 in the table).

Note!

Robomow has the power to mow high grass. However when mowing high grass during the first use or the first mowing of the season, initially you will see uneven patches of grass.

Please be patient as it may take a few days to one week to overcome and bring the lawn to an even height and consistency.

6.2

Operating Panel

Operating Panel and buttons:

User / Error messages

Mower is in the

Base Station indicator

Days of the week

Mo Tu We Th Fr Sa Su

AM

Battery and

Charging indicator

Red lit constantly – Low Battery

Green blinking – Charging

Green lit constantly – Fully Charged

Day and Time setting indicator

Area setting indicator

Intensity setting indicator

Rain Sensor Inactive Time setting indicator

30

Mowing with Edge /

Left arrow

Settings

OK to choose / approve selection

ok

STOP

Mowing without Edge /

Right arrow

GO to

Base (Home)

Stop (during operation) /

Back while in the menu

6.3

Manual Operation

Manual Operation is used when mowing the lawn at unscheduled times.

To initiate Manual Operation when Robomow is at the Base Station, press one of the buttons (except the STOP button) to show the display.

If the battery is fully charged and the mowing schedule is set to ‘On’, then the start time of the next operation is displayed, otherwise the current day and time are displayed.

Once the display is shown, choose the operation mode you want as provided in the table below:

Operation Mode

Mowing with Edge

Mowing the edge before starting to mow the inner area.

It is recommended to use this mode once or twice a week, depending on how fast the grass is growing.

Mowing without Edge

Mowing only the inner area without the edge.

It is recommended to use this mode only in the first operation of each Mowing Cycle.

Child Lock is Off

Press the ‘Edge before mowing’

(left arrow) button once

Press the ‘Mowing’ (right arrow) button once

Child Lock is On

Press the

(left arrow) button then press

Press the

‘Edge before mowing’

‘Mowing’ (right arrow) button then press OK

OK

Note – if a Sub-Zone is defined, then once you choose the Operation Mode, then L1 (Main Zone) will be displayed. Use the arrow buttons to scroll and choose the required zone to be mowed and press OK.

31

6.4

Menu Options

There are several levels of menu options that can be set in your Robomow:

A. Basic Settings

B. Advanced Settings

C. Robomow App Settings

6.4.1 Basic Settings

The Basic Settings are the most common menu options changed by the user. Each of the Basic Settings has an icon on the mower (refer to 6.2 – Operating Panel) that is lit to indicate the selected menu option. o To change Basic Settings, press the ‘Settings’ button.

o Every press on the Setting button will move between the following 4 menu options:

6.4.1.1 Day and Time – Set the current Day and Time.

Press the ‘Settings’ button so the ‘Day and Time’ (Clock) icon is constantly lit.

‘Day’ is blinking  Scroll to the required day and press OK to confirm;

‘Hours’ is blinking  Scroll to the required hour and press OK to confirm;

‘Minutes’ is blinking  Scroll to the required min and press OK to confirm;

6.4.1.2 Intensity - Increase/decrease the number of operating hours needed to cover the lawn size.

Press the ‘Settings’ button twice until the ‘Intensity’ LED is constantly lit.

Use the scrolling arrows to change the Intensity and press OK to confirm;

The default Intensity is 100% and it can be changed from 50% to 150%.

Example: Intensity of 120%, means that Robomow will run 20% more hours on the lawn.

32

6.4.1.3 Inactive Time – Set times when the mower will be inactive. Inactive operating times can be set for specific day(s) of the week, and for specific hours for all days in the week.

Inactive Day(s) defines the day(s) when the mower will be inactive (Default: Sunday).

Inactive Hours define the hours when Robomow will not mow and stays in the Base Station (Default:

23:00-06:00)

IMPORTANT!

It is required to go through the entire Inactive Days and Hours sequence in order to save the settings.

Pressing STOP before completing the whole sequence will not save the settings.

To change the Inactive Time, it is required to perform the following steps:

• Press the ‘Settings’ button 3 times until the ‘Inactive Time’ icon is constantly lit.

• The current Inactive Day(s) will constantly lit.

• Press the OK button; ‘Mon’ will start blinking.

-

Press the RIGHT arrow to scroll to the day you want to set.

-

Press ‘OK’ to toggle between ‘Active’ and ‘Inactive’ options for that day:

The LED is lit - ‘Inactive Day’ (mower will stay in the Base Station all day).

The LED is off - available day for mowing.

Press the RIGHT arrow to scroll to the next day you want to set

• Scroll through all the days to the right until the ‘Inactive Hours’ will start blinking.

• First set the time, which the Inactive Hours start and press ‘OK’. Then set the time which the Inactive

Hours will end.

• Robomow will not operate during the Inactive Hours throughout all days of the week.

• If too many days/hours have been deactivated relative to the zone area, then have enough time to mow your lawn.

E8

(Decrease Inactive

Time) will be displayed – you need to decrease the number of inactive time so that the mower will

• To set the ‘Inactive Hours’ to ‘Off’ set the same time for the start and the end (i.e.: 00

:

00 to 00

:

00).

• Only one window of Inactive Hours can be set in the Basic Settings. To open an additional window of

Inactive Hours use the Robomow App.

6.4.1.4 Area – Update the size of the lawn in case it h changed.

• Press the ‘Setting’ button 4 times until the Area icon is blinking.

• Scroll to change the area and press ‘OK’ to confirm.

• If more than one zone is defined, then first scroll to select the zone you want to edit and set the area for that zone as described above.

Names of zones are as follows:

L1 – Main Zone

L2 – Separated Zone A

L3 - Separated Zone B

A1 – Sub-Zone 1

A2 – Sub-Zone 2

A3 – Sub-Zone 3

A4 – Sub-Zone 4

6.4.2 Advanced Settings

The Advanced Settings are additional menu options that are not changed very often and thus are not included in the Basic Settings.

• To change any option/feature in the Advanced Settings, press the ‘Settings’ button continuously for 3 Sec.

• ‘P001’is displayed. Use the arrows to scroll to the setting you want to change, then press OK.

• Use the arrow button to change the setting and press OK to confirm.

• Scroll to change additional menu options or press STOP to go back to the main display.

Below are the Advanced Settings options:

Screen Setting

P001

Interval

(Default = 3 )

Description

• Controls the Interval (frequency) of mowing cycles in the zone.

• The default Interval is Twice a week. It means that Robomow will complete the entire mowing of your lawn twice a week (2 Mowing

Cycles every week).

• The numbers in the menu represent the following:

2 – Every two days

3 -Twice a week

7 - Once a week

14 - Every two weeks

• If there is more than one zone, the Interval can be set for all zones together or for each zone individually. You can choose All for all zones or scroll to the zone you want to change and change its setting.

• During off-season when the growth rate of the grass is slower, it is recommended to change the Interval to ‘Once a Week’ or ‘Every

Two Weeks’. This resting period helps the grass and prolongs the lifetime of the mower.

• Grass growth rate changes during the year (depending on temperature, grass type, fertilizing and etc.).

• High fertilization and favorable weather conditions may cause the grass to grow faster. In such cases, use the Interval option to decrease the time between cycles.

• The minimum Interval is Every 2 Days, but it is available only for relatively small areas, where the mower can complete mowing the area within 2 days.

Options

2/3/7/14

33

Screen

P002

P003

P004

P005

P006

P007

P008

P009

P010

Setting

Island

(Default =

Near Wire Follow

(Default = ON )

Rain Sensor

(Default = On )

(Default =

Child Lock

(Default =

OFF )

Max Near Wire

Follow Distance

(Default = changed based on the lawn area)

Min Near Wire

Follow Distance

(Default = 1 )

Near Wire Follow

Test

Rain Sensor

Sensitivity

(Default = 25

Edge On/Off

ON

)

)

OFF )

Description

• In rare cases, you may notice that the mower circles a Perimeter

Island unnecessarily while searching for the Base Station.

• The Islands option helps overcome this situation. To avoid such cases, turn the Islands feature On.

• When Robomow completes its operation, or when the ‘Home’ button instructs it to Go To Base, it drives itself to the Base Station.

• Robomow drives along the Perimeter Wire with a dynamic offset (not centered) to prevent wheel tracks along the same path. This return behavior can be turned off.

• The maximum distance Robomow will drive from wire when returning to the Base Station.

• The distance does not represent actual units of measurement.

• The offset Distance values range from 1 to 12. They represent different distances from the wire.

• The higher the Distance setting, the smaller the probability of tracks along the perimeter.

• Perimeter Islands that are relatively close to the Perimeter Wire or narrow passages may prevent the mower to complete its drive to the

Base Station in ‘Near Wire Follow’ mode. In such cases decrease the distance to allow the mower to complete the drive to the Base

Station.

• The minimum distance Robomow will drive from wire when returning to the Base Station.

• The larger the number, the bigger the distance the mower will drive from the wire while returns to the Base Station.

• Enables to test the mower in the max ‘Near wire Follow Distance’ that is defined in menu P004.

• If the mower is not able to complete the drive in ‘Near Wire’ mode smoothly, then it is recommended to reduce the max distance set in menu P004.

• The Rain Sensor feature halts operation on rainy or highly humid weather.

• This is recommended for the health of the lawn. However, mowing wet grass does not present any technical problem.

• Robomow detects rain when the current reading value is below the set Sensitivity value and postpones operation.

• The higher the Sensitivity setting, the more sensitive Robomow is to rain detection.

• The Edge is a special mode, in which Robomow follows the perimeter wire for complete and accurate owing of the lawn edges.

• In lawns where the edge is not maintained well and the mover fails to complete the drive along the edge of the lawn, it is recommended to set the Edge to ‘Off’.

• Setting the Edge to ‘Off’ disables the Edge mode in automatic departures from the station, but still allows the Edge mowing when pressing the ‘Edge’ mode button on the operating panel.

• The Child Lock feature locks the buttons to prevent unintended operation, especially by children.

• If the Child Lock is set to ‘On’, to operate the mower it is required to first press one of the operating mode buttons and then to press the

OK button to confirm.

Options

On/ OFF

On/ OFF

1-12

1-5

On/ OFF

0-30

On/ OFF

On/ OFF

34

Screen

P011

P012

P013

P014

P015

P016

P017

P018

P019

Setting

Anti-Theft

(Default = OFF )

Anti-Theft

Change PIN code

Base Station

(Default = ON )

Add Separated

Zone

Remove

Separated Zone

Description

• The Anti-Theft feature alarms the surroundings in the event of an unintended removal of the mower from its designated area.

• To turn the Anti-Theft On for the first time, set it to ‘On’ and choose a

PIN code of 4 digits.

Tip: Select a number you can remember. Write it down (bottom of

Chapter 10), and keep it in a safe place.

• When the Anti-Theft system is activated, 0000 will be displayed.

Enter your 4-digit code to deactivate the Anti-Theft.

• If the code is not entered, then the message is changed to U062

(Alarm will soon be activated). Enter the code, otherwise the alarm will start.

• Allows changing of the Anti-Theft PIN code.

• Enter a new code and then re-enter the new code for confirmation.

• This option should be used for a Separated Zone which has a

Base Station or when adding a Base Station to a model that does not have one.

• If you have defined more than one zone, then select the relevant zone before changing the setting.

• Enables the addition of a Separated Zone.

• L2 is displayed for Separated Zone A – press OK.

• Scroll to set the area of the Separated Zone and press OK.

• Enables the removal of a Separated Zone.

• Choose the Zone you ant to remove and press OK.

Sound

(Default = ON )

Mobile

Communication

System

(Default = OFF )

• Use the Sound option to turn all non-safety sounds off.

• Enables remote communication with the mower using a GSM

Module Accessory, which can be purchased separately.

• For more information refer to Section 12 – Accessories.

Statistics

(Default = OFF )

Bluetooth Remote

Control Pairing

• This menu is displayed only if P018 is set to ‘On.

• Enables to send the operation statistics from the mower to the manufacturer for diagnostics in case of problems.

• Enables the pairing process between your Robomow and an outdoor Bluetooth Remote Control that is available as an accessory (Refer to Paragraph 12 Accessories).

Options

On/ OFF

1234

0000

On/ OFF

L2

100

L2

L3

On/ OFF

On/ OFF

On/ OFF

6.4.3 Robomow App Settings

Using the Robomow App you will have access to additional menu options that are not available on the mower, such as an option to manage additional zones, and the option to set an additional window of Inactive Hours.

6.5 Operation in a Non-Base Zone (using a Perimeter Switch)

In order for Robomow to operate in a Non-Base Zone, the Perimeter Switch has to be turned on and the mower should be inside the active perimeter area.

• Verify that the Perimeter Switch is connected to the zone to be mowed.

• Press the ‘ON’ button to turn on the Perimeter Switch.

• Drive/carry Robomow to the lawn area.

• To initiate the operation, choose the operation mode you want, press the arrow buttons to choose the Zone you want to mow and press OK to start operation (refer to Section 6.3).

• When Robomow completes the mowing, it wil stay on the lawn. You will have to drive/carry it back to its place for charging.

35

7. Using The Power Box

7.1

Power Box Alerts

Event

Docking Indicator is lit.

Operating Indicator is lit

On/Off Button Indicator is lit.

‘OFF’ will be displayed on the mower.

Wire Indicator -

Flashes and Beeps

Alert

The mower is in its Base Station.

The mower is not in its Base Station.

Mowing schedule is Off.

All Indicators flash

All Indicators flash and Buzzer sounds for 10 seconds.

The Perimeter Wire is cut, disconnected, or too long.

The mower did not return to the Base

Station after 4 hours of departure.

When the mower is detected at the

Base Station, alerts will turn Off.

The Anti-Theft option is set to On, and the mower was removed from its Base Station when it was not scheduled to operate.

Docking Indicator

Operating Indicator

Note - To stop an alert when sounding, press the On/Off Button.

On/Off Button

Wire Indicator

7.2

Turn the Buzzer On/Off

• Press and hold the On/Off button for 10 seconds.

-

A short beep indicates On.

-

A flash indicates Off.

7.3

Disable the Automatic Operation

• This option is used to disable the predefined Automatic Operation of Robomow. This option does not prevent Manual Operation (Chapter 6.3).

• Press and hold the On/Off button for 2 seconds.

‘OFF’ will be displayed on the mower: o If Robomow is currently in the process of mowing:

- Robomow will complete the current mowing cycle.

- After returning to the Base Station, Robomow will not go out for its next scheduled operation.

• To Enable the Automatic Operation o Press and hold the On/Off button for 2 seconds.

36

8. Charging

8.1

Charging During the Season

The Base Station is the primary charging source when Robomow is docked and will maintain the optimal battery charge while awaiting departure.

8.2

Charging Out of Season

During out of season months, such as winter, it is required to:

• Fully charge the battery in the Base Station till the Battery indicator is green and lit constantly.

LED indicators for charging:

- R

ed is lit constantly – Charge the battery.

-

Green is blinking – During battery charging.

-

Green i

s lit constantly – Battery is fully charged.

• Remove Robomow from its Base Station. Turn the Safety Switch off and store the mower in a room temperature.

• If the mower is stored for more than 3 months, it is required to recharge the battery every 3 months till the Battery indicator shows it is fully charged.

• The charging can be done in one of the following options:

1. Plac

e the mower in the Base Station for charging.

2. Conne

ct Robomow directly to the Power Box as follows:

- Disconnect the DC Cable coming from the Power Box to the 15m Extension

Cable

and connect it to the rear side of the mower as . in the figure to the right.

• Once the season starts, just place Robomow in its Base Station to begin automatic operation.

9. Troubleshooting and User Messages

9.1 General Error Codes

Robomow continuously monitors its operation. It produces error codes to assist you in running it smoothly.

A sticker containing the most common error codes is provided in the box. You can place it on the mower for your convenience.

Rombow Error Codes Table

E 1 Stuck in Place E9* (See Troubleshooting in Manual) represents stops and error that are not very common, and thus they are not shown in the above Error Code

Table. If E9 is displayed, press the RIGHT arrow to receive the Error Code reason, for which the mower has stopped and refer to the User

Manual for more details.

E 2

E 3

E 4

E 5

E 6

Mower is Outside

No Wire Signal

Check Power

Check Blade / Cutting Height

Check Drive

• Usually, if the mower stops, an error code is displayed. This display stays on for 5 minutes. If you arrive later than those 5 minutes, the display will be blank.

E 7

E 8

E 9*

Front Wheel Problem

Decrease Inactive Time

See Troubleshooting in Manual

• To wake Robomow up and see the last error

E5XX Call Support

37

code displayed prior to stopping, press the OK button on the mower.

The following table displays all Error Codes and gives possible causes and corrective actions:

Display Message Probable Cause/Event Corrective Actions

E 1

E 2

Stuck in Place

The mower is

Outside place because the front wheel is ground.

- Rectify the reason for it getting stuck.

- Check the ground around the mower for and level off.

laid the wrong way around a perimeter island.

- The lawn slope is too steep along the edge.

- Robomow does not succeed to causing the mower to slip out of the designated area.

- Automatic operation is initiated the Perimeter Wire loop.

low for the grass condition - increase the cutting height if needed.

- Check that the Perimeter Wire is not towards the inner side of the lawn. laid according to the instructions in the

Manual.

- Do not include areas with very steep slopes.

- Verify that the cutting height is not set too low - Increase the cutting height.

- Place the mower inside the lawn and renew the operation.

- Make sure the Base Station is connected to the mains supply.

- Disconnect the Power Box from the mains power and reconnect after 10 seconds.

- Check that the low voltage cable between connected.

E 3 No Wire Signal connected to the Base Station/

Perimeter Switch.

- The Perimeter Wire is cut.

broken cable with the waterproofed connector supplied in the box.

E 4 Check Power

E 5 there is a physical contact between contacts.

current conditions for too long as a result of high grass or an obstacle that is stuck or wrapped around the blade.

- Something is preventing a blade from rotating freely (Accumulated grass clippings under the mowing wrapped around mowing blade).

- Turn power on to the power outlet.

- Check the power outlet using another appliance.

- Clean the contacts with a brush or piece of cloth.

- Confirm a good connection of the Power

Box to the Base Station.

- CAUTION – Switch off the Safety Switch before checking the blade.

- Inspect blade for foreign material or debris preventing rotation.

- Clean out accumulated grass clippings using a wooden stick.

38

Display

E 6

E 7

E 8

E 9

Message

Check Drive

Front Wheel

Problem

Probable Cause/Event

- Grass or other object has wrapped around the drive wheel.

- The drive motors have been working under severe load for too long.

Corrective Actions

- Check the drive wheels and remove the grass or other objects.

- The Front Wheel has left the ground for too long during operation.

Decrease

Inactive Time

See

Troubleshooting in Manual

- Too many Inactive Days and/or

Hours have been set for your lawn area.

- E 9 is displayed for all other messages that are not listed in the above table.

- If Robomow has driven onto an obstacle,

Switch off the Safety Switch, raising the front end: Remove or exclude the object from the mowing area.

- If Robomow is being used on a slope too steep for safe mowing, exclude this from the mowing area.

- If high grass is preventing the front wheel from fully turning on the ground, raise the cutting height.

- If the ground contains large holes or indentations where the front wheel can drop into when passing across, fill these areas with dirt and level off.

- Decrease the number of Inactive Days and/ or the number of Inactive Hours to allow

Robomow to complete mowing your lawn.

- Press the ‘Right arrow’ button to receive the stop reason number and refer to the next table for more details about the stop reason, causes, and actions.

9.2

Detailed Error Codes

If the above table (Section 9.1) does not give enough information to help solve the problem, then press the

RIGHT arrow while the error code is displayed in order to receive a number that gives more details about the problem and refer to the table below:

Display Message

0010

Mow

Overheat

Probable Cause/Event

-The drive motors have been working under a severe load for too long.

Corrective Actions

-No need for action – Robomow will renew mowing motor will cool down.

-No need to do anything.

-Robomow will renew the operation

0011

Drive

Overheat

0012 No wire signal -See E3 in the above table

0014

Front wheel problem

-See E7 in the above table

0015

Button pressed

-One of the operating panel buttons is constantly pressed.

continue operation. This message is displayed to inform only.

0016

Low temperature from the Base Station when the ambiance temperature is lower than 5ºC (41ºF).

-Information - When the temperature is below 5ºC (41ºF) the grass does not grow or grows very slowly.

However Manual Depart is enabled.

-No need to do anything.

-Robomow will renew the operation

0020 Rain detected -The operation is delayed as Robomow

-No need for action.

-The message is displayed until Robomow will not detect rain and then will start mowing.

39

Display

0021

Message

Check mowing height

Probable Cause/Event conditions for too long as a result of high grass or an obstacle that is stuck or wrapped around the blade.

-Something is preventing a blade from rotating freely.

-Severe grass accumulation under the mowing deck, rope, or similar object is wrapped around mowing blade.

Corrective Actions

0022

Check mowing motor too long in the Base Station before starting the operation.

0023

Check power -See E4 in the above table

Inspect the blade for foreign material or debris preventing rotation.

-Adjust the Base Station position.

0026

Base problem -Robomow fails to enter the Base Station

0027

Start

Elsewhere

-Drive wheel motors have been working manual operation.

-Check to insure the mower is not stuck, causing the drive wheels to slip.

-Check the ground around the mower for off.

40

-The Perimeter Wire is too close to the edge.

-The lawn slope is too big.

0028

0030

Cross Outside

Start Inside place at the edge and it causes the mower to slip out of the designated area.

-Robomow has slipped out of the Perimeter grass.

-Automatic operation is initiated while the robot is placed out of the Perimeter Wire loop.

0031

Stuck in place -See E1 in the above table

0060

Check

Intensity

-The Intensity you have set is too high for your lawn area.

0061

Decrease

Inactive Time

-See E8 in the above table

-Remove the wire towards the inner part of the lawn.

-Do not include this area because of its steep slopes.

-Fill holes and pits in the ground.

-Increase the cutting height.

-Place the mower inside the lawn and renew the operation.

-Decrease the Intensity you have set for the zone(s) in your lawn.

9.3

User Messages

The next table gives information about User Messages that can be displayed on the mower:

Display Message / Description

BATT Recharge Battery. Low battery voltage.

U001

U002

U003

U004

U018

Test Base Station position.

Displayed during the One-Time Setup.

Peg Base Station.

Displayed during the One-Time Setup.

Test wire position.

Displayed during the One-Time Setup.

Test wire ended (during the One-Time Setup)

Displayed only when using the Robomow App.

Operation time is shorter than expected

Action Required

Recharge the Battery.

Refer to section 5.2.4 in the User Manual.

Refer to section 5.2.4 in the User Manual.

Refer to section 5.2.5 in the User Manual

No action is required.

Battery run time is too short. Replace Battery.

Display

U024

Message / Description

Keep charging if not used.

Displayed only if the mower is disconnected from a Charging Adaptor.

U025 Switch Off before lifting

U029

U032

U041

U042

Change the wires in plot connector

Displayed during the One-Time Setup.

Switch on the System Switch.

Displayed if the mower is connected to charging, but the System Switch is ‘Off’.

Press the STOP button at Sub-Zone entry.

Displayed only when using the Robomow App to add a Sub-Zone.

Learning edge distance.

Displayed only when using the Robomow App.

U043

U044

U051

Going to Sub-Zone entry point.

Displayed only when using the Robomow App.

Place the mower in the Base Station.

Displayed only when using the Robomow App.

Reposition the Base Station position.

Displayed during the One-Time Setup.

U052 Adjust Wire

U062 An alarm will soon be activated.

U064

U086

U087

U088

The Searching Base Station operation cannot be performed

Waiting for the signal…

Robomow has stopped the operation. It does not detect a signal.

Mow motor overheat, Cooling…

The mowing motor has been working under a severe load for too long.

Drive motor overheat, Cooling…

The drive motors have been working under a severe load for too long.

Action Required

It is recommended to keep the mower connected to the Power Supply when not in use.

It is required to switch Off the System Switch before lifting and carrying the mower.

Swap the wires at the plot connector.

Refer to section 5.2.4 in the User Manual.

Switch the System Switch to ‘On’.

Press STOP at the point you want the mower to start mowing the Sub-Zone.

The mower learns the distance of the Perimeter

Wire in a Separated Zone. Press STOP to learn he distance.

Press OK to continue the process of adding a Sub-

Zone.

Place the mower in the Base Station before starting the process of adding a Sub-Zone.

Refer to section 5.2.4 in the User Manual.

Refer to section 5.2.5 in the User Manual.

This message warns you to enter the PIN code before the Anti-Theft alarm will sound.

When choosing the ‘Home’ button in a zone without a Base Station.

Check the power to the Power Box.

There may be an electrical power interruption.

There is no need to do anything. Robomow will renew operation as soon as the power is back on.

No need for action – Robomow will renew automatically the operation, as the mowing motor will cool down.

No need to do anything.

Robomow will renew the operation automatically as soon as the drive motor will cool down.

41

9.4 Fault Symptom

The next table will give details and possible causes of other faults, that do not provide error codes. If a fault cannot be dealt with using these tables, please call your service provider.

Problem

Encountered

Probable Cause/Event Corrective Actions

Poor quality of mowing

Mower doesn’t find the Base

Station

Robomow is noisy and vibrates

- Dull blade

- The grass is too high in relation to the set cutting height.

- The grass is wet and causes accumulation of grass clippings around the blade.

- There is a Perimeter Island or a Narrow

Passage that prevents the mower to complete its drive towards the Base

Station in Near Wire Follow mode.

- Damaged or unbalanced blade

- Replace blade.

- It is recommended to cut less than a 1/3 of the green part of the grass.

- Set the cutting height to a higher position and then successively lower.

- If it is during a fast growing season – change the

Interval (refer to Section 6.4.2 – P001).

- For best cut, operate Robomow when the grass is dry. Do no to mow in the early morning hours.

- Switch Off the Safety Switch and use heavy gloves to clean and remove the grass clippings.

- Reduce the Near Wire Follow Distance in the

Settings menu from the default 7.

Mower does not dock properly and sometimes misses the Base

Station contacts

Uneven mowing results

Robomow operates during

Inactive Time.

- Height differences between the lawn and the Base Station surface.

- The wire underneath the Base Station is not tight and placed in the middle of the

Station.

- The Base Station is set up on a side slope.

- The Base Station is placed too close to the corner of the lawn

- The time between operations is too long because of long inactive time windows.

- Grass is growing very fast.

- The shape of the lawn is complicated

(Narrow Passages, obstacle and islands).

- The set area is smaller than the actual lawn size.

- Wrong clock time is set in the mower.

- Check if the lawn is free from branches, stones or other objects that can damage the blade.

- Replace the blade

- Fill some ground to flatten the lawn to the Base

Station to allow smooth entrance.

- Confirm the wire underneath the Base Station is straight, tight, and centered below the Base

Station.

- Move the Base Station to a relatively level ground.

- Move the Base Station so it is not within 3 meters from a corner.

- Minimize the Inactive Time windows to allow

Robomow to complete the Mowing Cycle faster and to achieve even mowing results.

- If it is during a fast growing season – change the

Interval (refer to Section 6.4.2 – P001).

- In a complicated lawn more time is required for the lawn to achieve better mowing results.

- Increase the Intensity (refer to Section 4.3.2.1).

- Increase the zone area (refer to Section 4.3.3

Edit an existing Zone).

- Verify that the time on the mower is set correctly.

- Set the time (refer to Section 4.4.4).

- Reset the Inactive Time (refer to Section 4.3.1).

Cut wire indicator is flashing on

Power Box

- The Extension Cable is disconnected or damaged between Power Box and the

Base Station.

- Perimeter Wire is cut.

- Confirm the Extension Cable is plugged in and wire leads are firmly attached.

- Walk along Perimeter Wire.

- Look for cuts or breaks in the wire.

- Repair with Robomow wire splice connectors.

- Check and repair all loose, poor, or corroded connections.

The poor connection indicator is flashing on

Power Box

- Poor connections

- Twisted cables, or a screw terminal which is insulated with insulation tape is not a satisfactory splice.

- Soil moisture causes the conductors to oxidize.

- Use the connectors supplied in the box. They are waterproof and give a reliable electrical connection.

42

10. Product Specification

Max Lawn Size

Base Station

Robot Dimensions

Package Dimensions

Robot Weight

Package Weight

Cutting Width

Cutting Height

Mowing Power

Mowing Motors

Noise Level

Battery Type

Robot Part No.

RC 302 RC 304 RC 306

200 m 2

Available as Accessory

63 x 46 x 21 cm

80 x 54 x 33 cm

10.3 kg

22 kg

28 cm

15-60 mm

200 Watts

DC Brush

400 m 2

Included

63 x 46 x 21 cm

80 x 54 x 33 cm

10.3 kg

22 kg

28 cm

15-60 mm

200 Watts

DC Brush

600 m

Included

63 x 46 x 21 cm

80 x 54 x 33 cm

10.3 kg

22 kg

28 cm

2

15-60 mm

200 Watts

DC Brush

High Power: 68 dB measured (Guaranteed 70 dB)

The noise t the operator’s ears less than 70 dB

26V Lithium (LiFePO4) 26V Lithium (LiFePO4) 26V Lithium (LiFePO4)

PRD7002A PRD7004A PRD7006A

SIDE

BOTTOM

Anti-Theft PIN Code

Write down your 4-digit Anti-Theft PIN code.

Return here, if you ever forget the code.

Robomow Serial Number

43

11. Product Specification

11.1 General Instructions

• Always switch off the Safety Switch of Robomow® before clearing checking/ cleaning/ working on Robomow® or replacing the blade. Never attempt to service or adjust the mower while it is in operation.

• Check and clean Robomow® regularly and replace worn parts to improve performance and operation and to ensure a longer lifetime of your product.

• In case of abnormal vibrations, stop the mower, switch off the Safety Switch and check for any damage of the blade. Replace worn/damaged blade to preserve balance. If vibration continues, call for service.

• Use only the original equipment and accessories. It is not permitted to modify the original design of

Robomow®. All modifications are made at your own risk.

11.2 Battery Maintenance and Disposal

• The battery is maintenance-free, but has a limited lifetime of 2-4 years. Battery life is dependent on the season length and how many hours Robomow® is used. Thus it is recommended to change the ‘Interval’

(Section 6.4.2 – P001 in the table) when the growth rate of the grass is slower to prolong the lifetime of the mower and the battery.

• During out of season months, such as winter, it is required to keep Robomow continuously charged to avoid damage to the batteries (refer to Section 8.2 – Charging Out of Season).

• Disposing of the Old Battery Pack

• IMPORTANT! Do not place used batteries in your household trash. The battery must be collected, recycled, or disposed of in an environmentally sound manner. Return the old power pack to an approved battery recycler.

11.3 Winter Storage and Service

• Robomow®

- Clean Robomow® before putting it away for the winter storage.

- During winter, it is required to keep Robomow® continuously charged to avoid damage to the batteries

(refer to Section 8.2).

- Store the mower in a dry area, preferably at room temperature.

• Base Station

- Remove and store the Base Station Head indoors.

- Cover the Extension Cable end with its cover to prevent any damage of corrosion.

- The ends of the Perimeter Wire should be protected from damp by putting them in a container with grease.

• Winter Service

- To allow better maintenance and keep Robomow® in a good condition, it is recommended to bring your

Robomow® to a certified Robomow® dealer for service prior to winter storage.

- Winter Service includes operations as cleaning the mower parts and mowing deck, checking for wear parts and replace if required (such as blade, drive wheels and other moving parts), testing the mower functions and safety components, checking battery, and upload the latest software version, possibly including newly added features.

11.4

Maintenance of the Mowing Deck

Robomow is a dedicated mulching mower. It may accumulate clippings under the mowing deck, particularly when mowing wet or damp grass.

Warning!

Severe injury hazard!

Always turn the Safety Switch Off before lifting the mower.

The blade is very sharp. They can cause severe cuts or lacerations.

Always wear heavy work gloves when working with or around the blade.

NEVER, use a damaged or a broken blade. Use only a sharp blade.

44

• Inspect the underside of the mower periodically. Clean if necessary.

• Carefully scrape the collected grass debris from under the mowing deck.

- Most grass accumulation can be removed using a small wooden stick or similar object.

- You may remove the blade to gain better access to the mowing chambers.

IMPORTANT! Do not place the mower upside down.

Instead, lean the mower against a surface to gain access to the mowing deck area.

IMPORTANT! NEVER use a water hose or any type of liquid to clean the underside of the mower. Liquids can damage components.

Use only damp or wet cloth to wipe the surface clean after scraping.

11.5

Maintenance of the Blade

• Examine the cutting blade for damage periodically.

• Use only a sharp blade. Replace any damaged blade.

• Replace the blade once a year between seasons.

CAUTION! ALWAYS TURN THE SAFETY SWITCH OFF

BEFORE SERVICING BLADE!

IMPORTANT! After turning off the Safety Switch always reset the current day and time. Failure to do so may result in nonintentional operation of the Robomow.

IMPORTANT! Sharpening of the blade is not recommended, as it may create difficulties in balancing.

Safety Switch

To remove the blade:

- Insert the clamp side of the Blade Removal Tool into the open slits beside the locking tabs on either side of the blade.

- Turn the Blade Removal Tool slightly so that the clamp resides on top of the locking tabs on either side.

- Squeeze the handle of the Blade Removal Tool. The locking tabs on each side of the blade will be pressed (1).

- Pull the blade assembly off, away from the mower (2)

- When reinstalling the blade, line up the mating splines and push until a firm click is heard, indicating a proper seating of the blade onto the shaft.

45

11.6

Splicing the Perimeter Wire

If the Perimeter Wire needs to be spliced, use the connectors supplied in the Robomow box. It is waterproof and gives a reliable electrical connection.

IMPORTANT! Before slicing the Primeter Wire, disconnect the

Power Box from the power outlet.

1. Strip 1 cm (0.5 inch) of each wire end together and twist the stripped ends using pliers.

2. Insert the twisted wires into the splicing connector.

3. Screw the wire connector on the twisted wires. Make sure it is tightly secured.

IMPORTANT! Neither twisted cables, nor a screw terminal insulated with insulation tape are a satisfactory splice. Soil moisture will cause such conductors to oxidize and will later lead to a broken circuit.

11.7

Maintenance of the Base Station Area

• Keep the Base Station entrance and area clean of leaves, sticks, twigs or any other debris that usually accumulates in such areas.

• NEVER spray a water hose directly towards the Base

Station.

• Be careful when trimming around the Base Station with a powered weed trimmer as damage to the Extension Cable may occur.

• In the event of damage to any part of the Extension Cable, stop the use of the mower and the Base Station. Disconnect the Extension Cable and replace it.

11.8

Lightning storm

Warning! To reduce the risk of damage to components in the case of a lightning storm, disconnect the Perimeter Wire from the

Base Station /Perimeter Switch and the Power Box 230V/120V plug from the power outlet.

46

12. Accessories

Blade

Keep a spare blade on hand.

A sharp blade is important for safety and best cutting performance.

Perimeter Wire

For larger lawns or additional zones.

Wire Repair Connectors

Used for repairing or splicing wires

(as needed).

Base Station and

Power Box

Used for:

◦ Enabling multiple mowing cycles in a

Separated Zone

◦ Upgrade a model without a Base Station to work in a fully automatic mode.

Perimeter Switch

For zones that are not connected to the Base

Station.

Robomow App

Enables friendly an intuitive operation of your

Robomow and opens more menu options and features, which are not available through the mower Operating Panel.

Battery

Used to replace the existing battery and refresh cutting capacity.

Peg Pack

Used to fasten the

Perimeter Wire to the ground.

For larger lawns or additional zones.

Plot Connectors

Used for connecting the

Perimeter Wire to the

Base Station or Perimeter

Switch.

Remote Control

Used to Manually drive and mow anywhere.

Includes a Safety function to prevent accidental use.

Batteries Pack for

Perimeter Switch

Preferable for areas where electricity is not available or not close enough to the Perimeter

Switch

GSM Module

Enables remote alerts through the

Robomow App

(for all RC and TC models).

47

13. Tips for maintaining your lawn

Robomow®- Lawn care has never been so easy

Best time to mow

Mow your lawn when the grass is dry. This prevents the clippings from clumping and leaving piles on the lawn. Mow it late in the day rather than during the heat of the day.

Mowing frequency

Mow often, producing short, small clippings. During the active growing season the mowing frequency should be increased to once every 3-5 days, before the grass is too long. Short clippings decompose quickly and will not cover the grass surface. If the grass gets too high, raise the cutting height, mow, then gradually lower it over several mowings.

Cutting Height

Follow the “1/3 rule”. Mow no more than 1/3 of the length of the grass. Proper mowing will produce short clippings that will not cover up the grass surface.

You may have to cut the lawn more frequently, or double cut, when the lawn is growing fast, such as in the spring.

Grasscycling

Grasscycling reduces the amount of water needed by lawns since the clippings are about 80 – 85% water. Grasscycling slows evaporation losses from the soil surface, and conserves water. Most lawns need less water when Grasscycling.

Watering

Water your lawn between 4 a.m. and 8 a.m. in the morning, so water has time to soak into the soil before the heat of the sun causes evaporation.

Your lawn needs 1 to 1-1/2” (3-4cm) of water weekly. Deep watering allows grass to develop a deep root system, enabling the lawn to resist disease and drought.

Do not over water

Too much water is not only wasteful but can also increase turf growth, which requires more frequent mowing. Let the soil partially dry out between watering. Water when the top two inches of soil have dried out. Use an object such as a screwdriver to probe your soil and measure the depth of the moisture.

Fertilization

Grasscycling reduces the amount of lawn fertilizer needed because the clippings provide about 1/4 of a lawn’s annual needs.

Blade

Keep your mower blade sharp. A sharp blade provides a clean, safe, and efficient cut. A dull mower blade will tear and shred the tips of the grass, which can provide an entry for disease organisms and weaken the grass plant. It is recommended to replace the mower blade once a year.

Thatch

Clippings and thatch are simply not connected. As mentioned previously, grass clippings are approximately 80-85 percent water with only small amounts of lignin, and decompose rapidly.

When we stop and think about it, golf courses, sports fields, and parks, have been mowing grass for years and recycling with no grass catchers.

A small amount of thatch (approximately 1/2 inch) is actually beneficial to a lawn. Grass clippings protect your lawn’s root system from heat and water loss.

48

Warranty Card

RC Series Limited Warranty

Friendly Robotics warrants to the original purchaser that the RC series ‘Product’ is free from defects in materials and workmanship when used under normal residential* purposes for a period of 24 months, 12 months for the batteries, beginning from the date of purchase. Product accessories, including replacement batteries, are warranted for a period of ninety days from the date of purchase. This warranty provides for the cost of parts and labor to repair covered defects when performed by an authorized Friendly Robotics service and warranty facility. A valid proof of purchase is required for warranty repairs.

The limited warranty does not cover transportation costs of any kind. The owner bears all responsibility for transportation costs to an authorized Friendly Robotics service and warranty facility.

*Normal residential purposes are defined as the use of the product on the same lot as your primary home. Use at more than one location is considered commercial use, and this warranty would not apply.

Items and Conditions Not Covered

This express warranty does not cover the following:

• Cost of regular maintenance service parts or procedures, such as blade or blade sharpening.

• Any product or part that has been altered, misused, abused or requires replacement or repair due to accidents or lack of proper maintenance.

• Normal wear and tear, including fading of paint or plastic parts.

• Cost of installation or reinstallation, removal of installation or any costs or damages associated with improper installation or use of the product.

• Any product that has been opened, repaired, modified or altered by anyone other than a Friendly Robotics authorized repair facility.

• Repairs necessary due to improper battery care and/or improper charging process such as charging in wet conditions, electrical supply irregularities, or failure to properly prepare the mower or battery prior to any period of non-use.

• Repairs necessary due to water damage, other than incidental rain exposure, repairs due to lighting or other acts of God.

Instructions for Obtaining Warranty Service

Should you feel your Friendly Robotics product contains a defect in materials or workmanship, contact the retailer who sold you the product.

Owner Responsibilities

You must maintain and care for your Friendly Robotics product by following the maintenance and care procedures described in the User Manual. Routine maintenance, whether performed by a service provider or by you, is at your expense.

General Conditions

Repair by an authorized Friendly Robotics service and warranty repair facility is your sole remedy under this warranty.

There is no other express or implied warranty. All implied warranties of merchantability and fitness for use are limited to the duration of this express warranty. Friendly Robotics is not liable for indirect, incidental or consequential damages in connection with the use of the Friendly Robotics Product covered by this warranty, including any cost or expense of providing substitute equipment or service during reasonable periods of malfunction or non-use pending completion of repairs under this warranty. Some states do not allow exclusions of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusion and limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

Always Follow the Safety Instructions specified in this User Manual

49

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals