Always there to help you
Register your product and get support at
www.philips.com/support
Question?
Contact
Philips
User manual
AZB600
Contents
1Important
2
Safety2
Notice3
2 Your CD Soundmachine
4
3 Get started
7
4Play
9
8 Product information
16
9Troubleshooting
18
Specifications
16
Maintenance17
Introduction4
What's in the box
4
Overview of the main unit
5
Connect power
Turn on
Turn off
7
8
8
Play a CD
Play options
Play tape
Play from an external device
9
9
10
10
5 Listen to FM radio stations
11
6 Listen to DAB radio stations
13
7 Use system menus
15
Tune to FM radio stations
11
Program FM radio stations automatically 11
Program FM radio stations manually
11
Select a preset radio station
11
Adjust FM settings
12
Listen to DAB radio stations
For the first time use
Program radio stations
Display DAB information
Use DAB menus
Reset the product
Check the current software version
13
13
13
13
14
15
15
EN
1
1Important
•
•
Safety
•
•
•
•
•
•
•
•
•
•
•
•
2
Read these instructions.
Follow all instructions.
Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
Protect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the unit.
Only use attachments/accessories specified
by the manufacturer.
Unplug this unit during lightning storms or
when unused for long periods of time.
Recording is permissible insofar as
copyright or other rights of third parties
are not infringed upon.
Refer all servicing to qualified service
personnel. Servicing is required when the
unit has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have
fallen into the apparatus, the unit has been
exposed to rain or moisture, does not
operate normally, or has been dropped.
Battery usage CAUTION – To prevent
battery leakage which may result in bodily
injury, property damage, or damage to the
unit:
• Install all batteries correctly, + and - as
marked on the unit.
• Do not mix batteries (old and new or
carbon and alkaline, etc.).
• Remove batteries when the unit is not
used for a long time.
EN
•
Batteries (battery pack or batteries
installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
CAUTION: Danger of explosion if battery
is incorrectly replaced. Replace only with
the same or equivalent type.
The unit shall not be exposed to dripping
or splashing.
Do not place any sources of danger on
the unit (e.g. liquid filled objects, lighted
candles).
Where the MAINS plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
Warning
•• Never remove the casing of this apparatus.
•• Never place this apparatus on other electrical
equipment.
•• Never look into the laser beam inside this apparatus.
Caution
•• Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
Notice
This product complies with the radio
interference requirements of the European
Community.
Any changes or modifications made to this
device that are not expressly approved by
WOOX Innovations may void the user’s
authority to operate the equipment.
Disposal of your old product
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU. Inform yourself about the local
separate collection system for electrical and
electronic products. Follow local rules and never
dispose of the product with normal household
waste. Correct disposal of old products
helps prevent negative consequences for the
environment and human health.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
paper pulp (buffer) and polyethylene (bags,
protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
This apparatus includes these labels:
Class II equipment symbol
This symbol indicates that the apparatus has a
double insulation system.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offence.
This equipment should not be used for such
purposes.
Note
•• The type plate is located on the bottom of the
apparatus.
EN
3
2 Your CD
Soundmachine
Introduction
With this CD Sound machine, you can:
• Listen to FM radio;
• Listen to DAB radio;
• Enjoy audio from discs, tapes, and other
external audio devices;
• Program the play sequence of tracks.
The CD sound machine offers you Dynamic
Bass Boost (DBB) to enrich sound.
What's in the box
Check and identify the contents of the package:
• Main unit
• Power cord
• Short User Manual
• Safety sheet
4
EN
Overview of the main unit
e
a
f
g
b
h
c
i
d
j
k
o
BAND
FM
p
DAB
AUDIO-IN/CD RADIO TAPE/OFF
l
m
a DBB
• Turn dynamic bass boost on/off.
b
c
n
/
• Select a preset radio station.
/MENU
• Stop playing.
• Access FM/DAB menu.
EN
5
d MODE/DISPLAY
• Select a play mode.
• Display the RDS information.
• Display the DAB information.
e OPEN•CLOSE
• Open or close the disc compartment.
f Tape controls
•
Start tape play.
•
/
Fast rewind or fast forward the tape.
Stop the tape play or open the tape
door.
•
Pause tape play or pause recording.
g
/OK
• Start or pause play.
• Press to wake up the CD sound
machine from standby mode.
• Confirm a selection.
h PROG/PRESET
• Program the play sequence of tracks.
i
/
• Skip to the previous or next track.
• Search within a track.
j Display panel
• Display current status.
k FM antenna
• Improve FM reception.
l FM/DAB
• Select FM/DAB band.
m Source selector
• Select a source.
n VOL +/• Adjust volume.
o AUDIO-IN
• Connect an external audio device.
p AC MAINS ~
6
EN
3 Get started
Caution
•• Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of your apparatus. The
model number and serial number are on the
bottom of your apparatus. Write the numbers
here:
Model No. __________________________
Serial No. ___________________________
Connect power
The unit can be powered by either AC power
or batteries.
Option 1: AC power
Warning
•• Risk of product damage! Make sure that the power
AC~MAINS
Option 2: Battery power
Caution
•• Batteries contain chemical substances, so they should
be disposed of properly.
Note
•• Batteries are not supplied with the accessories.
1
2
3
Open the battery compartment.
Insert 6 batteries (type: 1.5V R14/UM2/C
CELL) with correct polarity (+/-) as
indicated.
Close the battery compartment.
supply voltage corresponds to the voltage printed on
the back or the underside of the unit.
•• Risk of electric shock! When you disconnect the AC
power, always pull the plug from the socket. Never pull
the cord.
Connect the AC power cord to the wall socket.
Tip
•• To save energy, turn the unit off after use.
EN
7
Turn on
Switch the source selector on the product to
CD/RADIO/TAPE.
Switch to standby mode
• The product switches to standby mode
automatically when there is no audio
detected for over 15 minutes.
• Press
to wake up the product from
standby mode.
Turn off
Switch the source selector on the main unit to
OFF.
8
EN
4Play
Play options
Control play
Play a CD
In CD mode, you can control play through the
following operations.
Note
/
•• You cannot play CDs encoded with copyright
protection technologies.
•• When an audio-in cable is plugged, CD playback stops,
and the unit switches to audio in mode automatically.
•• Make sure that no external device is connected with
the CD sound machine through AUDIO IN socket
before you play a CD.
You can play commercially available audio CDs:
• CD-Recordables (CD-R)
• CD-Rewritables (CD-RW)
1
2
3
PROG
+VOLUMEMODE
Switch the source selector to CD.
»» CD displays on the screen.
Open the CD compartment.
Insert a CD with the printed side facing up
and close the CD lid gently.
»» Your CD sound machine starts to play
automatically.
•
•
To select a track,press
/ .
To pause CD play, press
.
»» [ ] and track number flash.
•
•
To resume CD play, press
To stop CD play, press .
again.
Press:skip to the previous/next
track
Hold:search within play, then
release to resume play.
Start or pause play.
Stop play.
Program tracks.
Adjust volume.
Select a play mode.
[ ]: Play the current track
repeatedly.
[
]: Play all tracks
repeatedly.
[
]: Repeat all tracks
randomly.
To return to normal play, press
MODE repeatedly until the
repeat icons disappear.
Tip
•• Only[
] and [
] can be selected when you
play the programmed tracks.
Program tracks
AUDIO-IN/CD RADIO TAPE/OFF
In CD mode, you can program a maximum of
20 tracks.
1
2
3
4
Press
to stop playback.
Press PROG to activate the program
mode.
Press
/
to select a track number,
then press PROG to confirm.
Repeat steps 3 to program more tracks.
EN
9
5
Press
to play the programmed tracks.
»» During play, [PROG] (program) is
displayed.
• To erase the program, press
twice.
Adjust sound
During play, you can adjust volume and select
the sound effects.
Key
+VOLUMEDBB
Function
Increase or decrease volume.
Turn dynamic bass
enhancement on or off.
Play tape
Note
•• The CD sound machine will turns off automatically
AUDIO-IN/CD RADIO TAPE/OFF
Play from an external device
You can also listen to an external audio device
through this product.
1
2
after an elapsed time of inactivity at tape mode.
1
2
3
4
Slide the source selector to TAPE.
Press / on the CD sound machine to
open the tape door.
Load the tape with the open side upward
and the full spool to the right.
Press on the CD sound machine to start
play.
• To pause/resume play, press on main
unit .
• To rewind or fast-forward, press
/
on CD sound machine .
• To stop play, press
.
»» The CD sound machine turns off
automatically.
Note
•• In playback mode, cassette will be stopped
automatically when playback reaches the end.
•• There is no display on the LCD screen in tape mode.
10
EN
3
Switch the source selector to CD.
»» AUX IN displays on the screen.
Connect an audio cable (3.5mm, not
supplied) to:
• the AUDIO-IN socket on the unit.
• the headphone socket on an external
device.
Play the external device (see the device's
user manual).
Note
•• The AUDIO-IN socket is not for headphones.
Audio-in
5 Listen to FM
radio stations
Program FM radio stations
automatically
Note
•• You can program a maximum of 20 preset radio
stations.
Tune to FM radio stations
In FM tuner mode, press and hold PROG for 2
seconds to activate automatic programming.
»» All available radio stations are stored
automatically, then the first stored
radio station is broadcast.
Note
•• For optimal reception, fully extend and adjust the
position of the FM antenna.
1
2
3
»» [FULL] is displayed when 20 preset
radio stations are stored.
Switch the source selector to RADIO and
switch the band selector to FM.
Press
/
to tune to a radio station.
Repeat step 3 to tune to more stations.
• To store the current radio station,
press PROG twice.
Program FM radio stations
manually
Note
•• To overwrite a programmed radio station, store
another station in its place.
1
2
3
BAND
FM
AUDIO-IN/CD RADIO TAPE/OFF
DAB
4
Tune to a radio station.
Press PROG to activate programming.
Press
/
to allocate a number to
this radio station, and then press PROG to
confirm.
»» [STORED] and the frequency of this
radio station are displayed.
Repeat steps 1-3 to program more
stations.
Select a preset radio station
In tuner mode, press
station.
/
to select a preset
EN
11
Adjust FM settings
1
2
In FM mode, press MENU to access FM
menus.
Press / to toggle through the menus.
• [SCAN SET]: Access the scan settings.
• [SYSTEM]: Access system settings.
Scan setting
1
2
3
Press OK to access the [SCAN SET]
menu.
Press / to select an option:
• [STRONG]: Search for strong stations
only.
• [ALL]: Search for all stations no matter
whether the signal strength of a station
is strong or weak.
Press OK to confirm the selection.
System menus
1
2
Press OK to access system menu.
•
Press / to to select a sub-menus.
For details, refer to the section 'Use
system menus'.
12
EN
6 Listen to DAB
radio stations
3
Listen to DAB radio stations
Program radio stations
Note
•• For optimal reception, fully extend the antenna and
adjust its position.
•• You can program a maximum of 20 DAB radio stations.
•• Check with local retailer or go to www.WorldDAB.org
for applicable DAB radio frequencies in your area.
1
2
3
4
5
»» After the search is complete, the
first stored radio station is broadcast
automatically.
Press
/
to select a station, and then
start listening.
Tune to a DAB radio station.
Press PROG to activate the programming.
Press
/
number.
to select a preset sequence
Press PROG to confirm.
»» The radio station is stored with the
selected sequence number.
Repeat steps 1-4 to program more radio
stations.
Note
•• If you store a radio station with the sequence number
of another one, the earlier one is overwritten.
BAND
FM
DAB
Display DAB information
AUDIO-IN/CD RADIO TAPE/OFF
For the first time use
1
2
Switch the source selector to RADIO and
switch the band selector to DAB.
»» [Full scan] menu is displayed.
Press OK to activate the automatic search.
»» This product automatically stores radio
stations with sufficient signal strength.
On the display of DAB broadcasting, the first
line shows station name, and the second line
shows the service information for the current
station.
Press DISPLAY repeatedly to cycle through the
following information (if available).
• Dynamic label segment (DLS)
• Signal strength
• Program type (PTY)
• Ensemble name
• Frequency
• Signal error rate
• Bitrate codec
• Time
• Date
EN
13
Use DAB menus
1
2
3
In DAB mode, press MENU to access the
DAB menus.
Press / to toggle through the menus.
• [FULL SCAN]:Scan for the DAB
stations.
• [MANUAL]: Tune to a station manually.
• [DRC]:Enable or disable DRC.
• [PRUNE]: Remove invalid stations
• [SYSTEM]: Access system setting menu.
Press OK to enter the menu.
3
Press OK to confirm the selection.
Remove invalid stations
This option lists active stations and removes any
stations that are in the list but have no service
in your area.
1
2
3
Press OK to access the [PRUNE] menu.
Press
/
to select an option.
• [N]: Return to the previous menu.
• [Y]: Remove invalid stations from the
station list.
Press OK to confirm the selection.
Re-scan for stations
System menus
Full scan is used to perform a wide range
search for DAB radio stations.
• Press OK to activate the automatic search.
»» This product automatically stores radio
stations with sufficient signal strength.
1
2
Tune to a station manually
With this feature, you can tune to a specific
channel/frequency manually. In addition to
antenna orientation for better radio reception,
the optimal reception can also be obtained with
this feature.
1
2
3
Press OK to access the station list.
Press
/
to select a station.
Press OK to confirm the option.
DRC (Dynamic Range Control)
DRC adds or removes a degree of
compensation for the differences in the dynamic
range between radio stations.
1
2
14
Press OK access the sub-menus.
Press / to select an option.
• [DRC OFF]: No compensation applied.
• [DRC LOW]: Medium compensation
applied.
• [DRC HIGH]: Maximum
compensation applied.
EN
•
Press OK to access system menu.
Press / to to select a sub-menus.
For details, refer to the section 'Use
system menus'.
7 Use system
menus
With the system menus, you can:
• [RESET]: Reset the product to factory
default status.
• [UPGRADE]: Upgrade the software.
• [SW VER]: Check the version of current
software of this product.
Reset the product
1
2
3
Press OK to display the options.
Press
/
to select an option.
• [N]: Return to the previous menu.
• [Y]: Reset the product to factory
default status.
Press OK to confirm the option.
Check the current software
version
Press OK to display the version of current
software.
EN
15
8Product
information
Note
•• Product information is subject to change without prior
notice.
Specifications
Tuner
Tuning Range
Sensitivity:
Mono, 26dB S/N Ratio
Stereo, 46dB S/N Ratio
Search Selectivity
Total Harmonic Distortion
Signal to Noise Ratio
FM: 87.5 108MHz
DAB: 174.928 239.200 MHz
<22 dBf
<43 dBf
50 KHz (FM)
<3%
>50 dBA
Tape deck
Amplifier
Rated Output Power
Frequency Response
Signal to Noise Ratio
Total Harmonic Distortion
Audio-in Input
2 x 1 W RMS
125 -16000
Hz, -3dB
>55 dBA
<1 %
650 mV RMS
Disc
Laser Type
Disc Diameter
Support Disc
Audio DAC
Total Harmonic
Distortion
Frequency Response
S/N Ratio
16
EN
Semiconductor
12cm/8cm
CD-DA, CD-R,
CD-RW
24Bits / 44.1kHz
<1%
125 -16000 Hz,
-3dB
>55 dBA
Frequency response
- Normal tape (type I)
Signal-to-noise ratio
- Normal tape (type I)
Wow and flutter
125 - 8000 Hz
(8 dB)
35 dBA
≤ 0.4% DIN
General
Power supply
- AC Power
- Battery
Operation Power
Consumption
Standby Power
Consumption
Dimensions
- Main Unit (W x H x D)
Weight (Main Unit)
220-240V~,
50/60 Hz;
DC 9 V, 6 x 1.5 V
type: R14/UM2/C
CELL
10 W
<0.5 W
300 x 134 x 240
mm
1.5 kg
Maintenance
Clean the cabinet
• Use a soft cloth slightly moistened with
a mild detergent solution. Do not use a
solution containing alcohol, spirits, ammonia
or abrasives.
Clean discs
• When a disc becomes dirty, clean it with
a cleaning cloth. Wipe the disc from the
centre out.
Demagnetise the heads
• Use a demagnetising tape available at your
dealer.
•
Do not use solvents such as benzene,
thinner, commercially available cleaners,
or antistatic spray intended for analogue
records.
Clean the disc lens
• After prolonged use, dirt or dust may
accumulate at the disc lens. To ensure good
play quality, clean the disc lens with Philips
CD lens cleaner or any commercially
available cleaner. Follow the instructions
supplied with cleaner.
Clean the heads and the tape paths
• To ensure good recording and play quality,
clean the heads A, the capstan(s) B, and
pressure roller(s) C after every 50 hours
of tape operation.
• Use a cotton swab slightly moistened with
cleaning fluid or alcohol.
•
You can also clean the heads by playing a
cleaning tape once.
EN
17
9Troubleshooting
Warning
•• Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support). When you contact Philips,
make sure that the device is nearby and the
model number and serial number are available.
No power
• Ensure that the Mains cord is connected
securely.
• Ensure that there is power at the AC
Mains.
• Ensure that the batteries are inserted
correctly.
No sound or poor sound
•• Adjust the volume.
No response from the unit
•• Disconnect and reconnect the AC power
plug, then turn on the system again.
•• As a power-saving feature, the unit
switches off automatically 15 minutes after
track play reaches the end and no control
is operated.
Poor cassette sound quality
• Ensure that heads in the cassette holder
are clean.
• Ensure that a NORMAL (IECI) cassette
tape is used for record.
Cassette does not work for record
• Ensure that cassette tabs are not broken.
18
EN
No disc detected
•• Insert a disc.
•• Check if the disc is inserted upside down.
•• Wait until the moisture condensation at
the lens has cleared.
•• Replace or clean the disc.
•• Use a finalized CD or correct format disc.
Poor radio reception
•• Increase the distance between the unit and
your TV or VCR.
•• Fully extend the FM antenna.
Specifications are subject to change without notice.
2014 © WOOX Innovations Limited.
All rights reserved.
Philips and the Philips’ Shield Emblem are registered
trademarks of Koninklijke Philips N.V. and are used by WOOX
Innovations Limited under license from Koninklijke Philips N.V.
AZB600_12_UM_V1.0