Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 1 Jeudi, 12. février 2015 11:31 11
Register your product and get support at
Screeneo
www.philips.com/welcome
HDP1650TV
HDP1690TV
US User Manual
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 2 Jeudi, 12. février 2015 11:31 11
Table on Contents
Overview ...................................................3
Dear Customer ....................................................................3
About this User Manual ......................................................3
What's in the Box ................................................................3
Product Highlights ...............................................................3
1 General Safety Information ................4
Setting up the Device ..........................................................4
Automatic device temperature control ..........................4
Repairs ....................................................................................4
Power Supply ........................................................................5
Wireless Network (WLAN) .............................................5
3D glasses use .......................................................................5
Dolby Digital .........................................................................5
2 Overview ...............................................6
Front View .............................................................................6
Rear View ..............................................................................6
Remote Control ...................................................................7
Browsing the user interface ...............................................8
Overview of the Menu Functions .....................................9
Symbols in the Statusbar ....................................................9
3 Initial Operation ................................10
Setting up the Device ........................................................10
Connect Power Supply .....................................................10
Installing or Changing the batteries of the
IR Remote Control ............................................................10
Using the Remote Control ..............................................11
Installing or Changing the batteries of the
RF Remote Control ...........................................................11
3D glasses ............................................................................14
Initial Installation .................................................................15
4 Connect to the Playback Device ......16
Connecting to Devices with HDMI Output ................16
Connecting to a Computer (VGA) ................................16
Connecting Using an Audio/Video
(CVBS) Adapter Cable ......................................................17
Connecting to a home cinema amplifier .......................17
Connecting to a Hi-Fi unit ...............................................17
Connecting the headphones ............................................18
WiFiDisplay (Miracast) ......................................................18
Directly Connecting Projector to Computer
using WLAN (WiFi Streaming) .......................................18
ScreeneoWLink software ................................................18
5 Memory ...............................................21
Inserting a Memory Card .................................................21
Connecting USB Storage Medium ..................................21
6 Network ..............................................22
LAN Network ....................................................................22
Wireless Network (WLAN) ...........................................22
Switching Wireless Networking (WLAN) on/off .......23
Setting up a Wireless Network (WLAN) ....................23
Setting up a Wireless Network (WLAN)
using the Wizard ................................................................ 23
Wifi Hotspot ....................................................................... 24
Digital Living Network Alliance (DLNA) ..................... 25
7 Bluetooth ........................................... 26
Activating the Bluetooth connection ............................ 26
Setting up Bluetooth parameters ................................... 26
Bluetooth speaker ............................................................. 26
8 Media Playback .................................. 28
Navigating in the media Playback ................................... 28
Video playback .................................................................... 29
Photo Playback ................................................................... 29
Music Playback .................................................................... 31
Managing Files ..................................................................... 32
9 Digital TV Playback
(Depending on model) ........................... 33
Connecting the Aerial ...................................................... 33
First Playback ...................................................................... 33
Television ............................................................................. 34
Modifying the DVB-T settings ......................................... 34
10 Android ............................................... 35
Starting Android Apps ...................................................... 35
Exiting Android .................................................................. 35
Installing Android-Apps .................................................... 35
11 Settings ............................................... 36
Overview of the Menu Functions .................................. 36
12 Service ................................................ 38
Cleaning ............................................................................... 38
Device Overheated ........................................................... 38
Update Firmware with Memory Card .......................... 38
Troubleshooting ................................................................. 39
13 Appendix ............................................ 41
Technical Data .................................................................... 41
Accessories ......................................................................... 41
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 3 Jeudi, 12. février 2015 11:31 11
Overview
Dear Customer
What's in the Box
Thank you for purchasing our projector.
We hope you enjoy your device and its many functions!
1 – Projector
2 – Remote Control (with 2AAA battery)
3 – A/C power cable
4 – USB - Mini USB Cable for charging 3D glasses
5 – 3D Glasses with a quick start guide, a warning label
and a protection bag (depending on model)
6 – Quick Start Guide
7 – Warranty Guide
8 – Bag
About this User Manual
With the installation guide on the following pages, you
can start using your device quickly and easily. Detailed
descriptions can be found in the following sections of
this user manual.
Read the entire user manual carefully. Follow all safety
instructions in order to ensure proper operation of
your device. The manufacturer accepts no liability if
these instructions are not followed.
This user manual describes several versions of the product.
An infrared remote control (IR) is provided with the
HDP1650 and HDP1650TV models.
A radio frequency remote control (RF) is provided with
the HDP1690 and HDP1690TV models.
a
b
GUIDE
SOURCE
AMBILIGHT
3D
TV
FORMAT
SMART
TV
LIST
INFO
c
OK
OPTIONS
EXIT
CH -
CH +
1.@
2 ABC
4 GHI
7 PQRS
SUBTITLE
DEF
3
5 JKL
MNO
6
8 TUV
WXYZ
9
0
d
TEXT
PHILIPS
e
f
g
h
Symbols Used
Notice
Troubleshooting
This symbol designates tips that will help you
to use your device more effectively and easily.
CAUTION!
Damage to the Device or Loss of Data!
This symbol gives warning of damage to the
device and possible loss of data. This damage
can result from improper handling.
DANGER!
Product Highlights
Connecting to devices with HDMI output
With a HDMI cable you can connect the projector to a
computer or laptop (see Connect to the Playback
Device, page 16).
WiFiDisplay (Miracast)
With the Miracast™ solution you can display video
between Wi-Fi devices, without cables or a network
connection. You can do things like view pictures or videos from a smartphone or laptop on your projector.
Danger to Persons!
This symbol gives warning of danger to persons. Physical injury or damage can result
from improper handling.
3
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 4 Jeudi, 12. février 2015 11:31 11
1 General Safety Information
Do not make any changes or settings that are not
described in this user manual. Physical injury or damage
to the device or loss of data can result from improper
handling. Take note of all warning and safety notes indicated.
Do not expose the device to extreme vibrations. It may
damage the internal components.
Do not allow children to handle the device without
supervision. The packing materials should be kept out of
the hands of children.
Setting up the Device
Automatic device
temperature control
The unit is for indoor use only. The device should be
placed securely on a stable, flat surface. Position all
cables in such a way that no one will stumble on them,
thus avoiding possible injuries to persons or damage to
the device itself.
Do not plug in the device in moist rooms. Never touch
the mains cable or the mains connection with wet
hands.
The device must have sufficient ventilation and may not
be covered. Do not put your device in closed cabinets
or boxes.
Do not place the machine on soft surfaces such as tablecloths or carpets and do not cover the ventilation slits.
Otherwise the device could overheat or catch fire.
Protect the device against direct sunlight, heat, large
temperature fluctuations and moisture. Do not place
the device in the vicinity of heaters or air conditioners.
Observe the information on temperature and humidity
in the technical data.
Do not allow liquids to enter into the device. Switch off
the device and disconnect it from the mains supply if liquids or foreign substances end up inside the device.
Have the unit inspected by a technical service department.
Always handle the unit with care. Avoid touching the
lens. Never place heavy or sharp objects on the projector or the power cable.
If the projector gets too hot or emits smoke, shut it
down immediately and unplug the power cable. Arrange
for your device to be investigated by a technical service
centre. To prevent the spread of fire, open flames
should be kept away from the device.
Under the following conditions, a layer of moisture can
appear inside the device which can lead to malfunctions:
• if the device is moved from a cold to a warm
area;
• after a cold room is heated;
• when this device is placed in a damp room.
This device include an automatic thermal management
controller. If the internal temperature gets too hot, the
Fan speed will automatically increase (noise increase), if
the temperature still continue to growth, the brightness
of your product will decrease and in worst case the current symbol will appear.
The product will automatically switch off the display
after displaying this message during 5s.
This kind of behaviour should not arrive except if the
outside temperature is very high (>35°C). In such case
return the product to the manufacturer would be recommended.
Repairs
Do not repair the device yourself. Improper maintenance can result in injuries or damage to the device.
Your device must be repaired by an authorised service
centre.
Find details of authorised service centres on the warranty card.
Do not remove the type label from your device; this
would void the warranty.
Proceed as follows to avoid any moisture build-up:
1 Seal this device in a plastic bag before moving it to
another room, in order for it to adapt to room conditions.
2 Wait one to two hours before you take the device
out of the plastic bag.
The device should not be used in a very dusty environment. Dust particles and other foreign objects may
damage the unit.
4
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 5 Jeudi, 12. février 2015 11:31 11
Power Supply
Before turning on your device, check that the outlet
that you are going to plug it into conforms to the indications shown on the information plate (voltage, current, power network frequency) located on your
device. This device shall be connected to a single phase
power network. The device shall not be installed on
bare ground.
Only use the power cable that is supplied with your
device. Your device is delivered with a grounded power
cord. It is imperative to connect a grounded connector
to a grounded outlet connected to the building earthing.
The socket outlet shall be installed near the equipment
and shall be easily accessible.
The product should be supplied by a power system
compliant with LPS requirements of 2.5 of UL60950-1.
In case of failure, the power cable is the disconnect
device for this equipment. To remove all electrical
power from the equipment, disconnect the power cable
from the electrical outlet.
Turn off the device and unplug from the power outlet
before cleaning the surface. Use a soft, lint-free cloth.
Never use liquid, gaseous or easily flammable cleansers
(sprays, abrasives, polishes, alcohol). Do not allow any
moisture to reach the interior of the device.
• how to make a proper and regular cleaning and
disinfection in the case of any particular eventualities-ocular infections, infestations of the head,
mixed use, etc... where disinfection of the glasses
is not possible as it may damage the functionality
of the 3D glasses must be communicated to the
consumer that in presence of these eventualitiesinfections is contraindicated the use of 3D
glasses for the person concerned until the disappearance of the above circumstances;
• 3D glasses must be kept out of children if there
is the presence of small moving parts ingestible;
• 3D glasses are to be used together with the
instruments of vision correction in case the consumer is the bearer of lenses (eyeglasses or contact lenses);
• You should stop watching 3D in the event of the
occurrence of eye problems or discomfort, and
in the event of a persistence of the same, consult
a doctor.
Dolby Digital
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of
Dolby Laboratories.
DANGER!
High Power LED
This device is equipped with high power LED
(Light Emitting Diode), which emit very bright
light. Do not look directly into the projector
lens. This could cause eye irritation or damage.
Wireless Network (WLAN)
The functioning of security systems, medical equipment
or sensitive devices can be disrupted by the transmission power of the device. Observe any usage regulations (or restrictions) in the vicinity of such equipment.
The use of this device can affect the operation of insufficiently shielded medical devices and hearing aids and
pacemakers through the release of high frequency radiation. Also consult a doctor or the manufacturer of the
medical device to establish whether these are sufficiently shielded from external high frequency radiation.
3D glasses use
The use of 3D glasses in home for watching TV shows:
• is contraindicated for children less than 6 years
old;
• for children from 6 years old to adulthood,
should be limited to the vision for a maximum
time equal to the duration of a film show;
• the same time limit is also recommended for
adults;
• must be restricted to watching only 3D content;
General Safety Information
5
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 6 Jeudi, 12. février 2015 11:31 11
2 Overview
Front View
Rear View
1 Control panel for navigation and operation
u – To display the home menu
¿ – One menu step back, one directory level back
/ cancelling a function
//À/Á – Navigation keys / navigate the
menu / modify settings
– Confirms selection
B– Long press: Power off the projector
Short press: ECO mode on / off
2 Ï – Audio output – headphone connection or connection for external speakers
3 3– HDMI port for a playback device
4 – Memory card slot
5 ý – USB port for a USB storage medium or to connect accessories (mouse or keyboard).
6 Focus wheel for image sharpness
1 – Power supply outlet
2 ý – 2 USB ports for a USB storage medium
3 – Digital audio connector
4 – HDMI 1 and 2 ports for a playback device
5 Kensington Security System Connector
6 VGA – Personal Computer input
7 – LAN network connector
8 – Analog audio connectors
9 / – A/V port for a playback device
– Remote screen connection
– Aerial socket for TV connection
– Lens
a
PHILIPS
S/PDIF
OPTICAL
a
b
6
f
PHILIP
S
c
d
e
b
c
d
e
1
2
VGA
L
R
AUDIO
OUT
f g
AV
IN
TRIG
OUT
j
i
h
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 7 Jeudi, 12. février 2015 11:31 11
3 EPG –To display the electronic program guide.
3D – To display the 3D menu.
Favorite – To display the favourite list in DVB-T
mode.
Remote Control
4 To display the home menu.
5 TAB key or Toggle between TV and Radio channels in DVB-T mode and browsing the Internet
without external keyboard.
a
b
c
6 Navigation keys
– Confirms selection
/, À/Á – Navigation keys / navigate the
menu / modify settings.
/
7 EXIT – One menu step back, one directory level
back / cancelling a function.
d
e
f
g
MENU
TAB
8 PAGE/CH- PAGE/CH+ –To select the previous
channel/page or the next channel/page.
9 Color keys - On-screen options.
Number keys and text keypad.
Short press for numbers and long press to
switch "letters"
SUB/SHIFT – To display subtitles in DVB-T mode
or shift key in input mode.
I
TTX/← – To display Teletext pages when available
in DVB-T mode or backspace key in input mode.
h
/
/
– / + – To adjust the volume level (to decrease/increase and to mute the sound).
i
RECALL – To recall the last function or the last
channel viewed in DVB-T mode.
OPTIONS – To call the option menu.
j
INFO – To display program information on current
program in DVB-T mode.
SUB/SHIFT
MENU – To display the settings menu in DVB-T
mode.
SOURCE – To display the list of input connections.
SMART SETTINGS – To display the Smart settings menu
FORMAT – To change the aspect ratio.
1 Long press: Power off the projector.
Short press: Power on the projector or ECO mode
on/off.
To power the projector on use the B key on the
control panel
For radio frequency remote control (RF), a QWERTY
keyboard is available below for you to enter text easily.
2 Playback keys
– Skip backward (music only)
– To stop playback
TAB
– Skip forward (music only)
– To rewind
– To start / pause playback
– To fast-forward
Overview
7
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 8 Jeudi, 12. février 2015 11:31 11
Browsing the user interface
Navigation for setting menu
Infrared Remote Control (IR)
Navigation can be done by navigation keys (,,
À,Á, OK and ¿) on the control panel or the
remote control, as well as by an air mouse.
Navigation by keys:
• / scrolls trough the menu level up and
down.
• OK/Á goes one level down, with À / ¿ one
level up.
• u goes back to the main screen.
• In the final level, accepts a setting and goes
back to the last sub menu.
• The ¿ key aborts a setting and goes back to the
last sub menu (or exits the menu depending on
which menu)
Radio freqency Remote Control (RF)
If there are more menus listed than displayed you can
scroll the list by clicking into the list and move up and
down without releasing the left mouse button.
With the right mouse key you can exit the menu and go
back to the next top level menu.
Software Keyboard
Notice
To enter text, you can also use standard computer keyboard or mouse. It is possible to use
wired models (USB) as well as wireless models with 2.4 GHz USB-connectors.
When you need to enter data, the projector displays a
virtual keyboard which allows you to enter text, numbers and punctuation marks, etc.
1 Select the input field using the ,,À and Á
keys, then press the OK key to display the keyboard
or click in the input field using the air mouse.
2 The software keyboard appears.
3 Enter the text on the software keyboard.
To use the RF remote control you must connect the
supplied receiver into a USB port, refer to the chapter
“Initial Operation” page 10.
For activate the mouse touch and hold the OK button
until the pointer on the screen appears.
Select an icon by pointing with the pointer and clicking
with the OK key of the remote control.
Navigation by keys:
• / scrolls trough the menu level up and
down.
• OK/Á goes one level down, with À / ¿ one
level up.
• u goes back to the main screen.
• In the final level, accepts a setting and goes
back to the last sub menu.
• The ¿ key aborts a setting and goes back to the
last sub menu (or exits the menu depending on
which menu)
To use the QWERTY keyboard
• ,,À and Á scrolls trough the menu.
• ENTER/Á goes one level down, with À one
level up.
• Fn to use blue characters
Navigation by (air) mouse: (like standard
mouse operation within Android)
CAUTION!
Air mouse
The air mouse is not provided with Screeneo
HDP1650TV.
Select an icon by pointing with the mouse pointer and
clicking with the left mouse key.
8
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 9 Jeudi, 12. février 2015 11:31 11
Overview of the Menu
Functions
Symbols in the Statusbar
1 After switching on the device the main menu
appears.
2 Select the desired menu using the navigation keys
/, À/Á.
3 Confirm with OK.
4 By pressing the u key you will return to the main
menu.
a b
c de
1 – Time
2 – Date
3 – LAN status display
4 – Bluetooth status display
5 – WiFi status display
HDMI 1, 2, & 3 – Switch to the external video input
HDMI.
TV1 – Television
DLNA – Displays the list of the devices found on the
Network.
Memory – Display the content of the internal memory and the inserted memory SD-Card (movies, pictures, musics, folderview).
USB – Display the content of the connected USB
media (movies, pictures, musics, folderview).
WWW – Open an Internet web browser.
VGA – Switch to the Personal computer input.
A/V-in – Switch to the Audio Video input.
APPs – Call the android operating system.
Settings – Configure settings for the wished used of
the device.
1.Depending on the device model, TV can be
replaced by BT speaker.
Overview
9
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 10 Jeudi, 12. février 2015 11:31 11
3 Initial Operation
Setting up the Device
Before installing your device, make sure that the
projector is turned off and the power cord is
unplugged from the power outlet.
CAUTION!
Remove protection foil before operation!
Do not place any objects in front of the lens!
You can position the device so that it lies flat on a table
in front of the projection surface; it is not necessary to
tilt it towards the projection surface. The device compensates for the distortion from the slanted projection
(pincushion distortion).
Check that the projection surface is appropriated to the
projector. The distance between the projector and the
screen determines the actual size of the image.
Connect Power Supply
CAUTION!
The power cord is used as a power unit cut
off. As a precaution, the outlet shall be located
close to the device and be of easy access in
case of danger.
1 Connect the power cord into the socket on the rear
side of your device (1).
2 Plug the power cord to outlet on the wall (2).
PHILIPS
S/PDIF
OPTICAL
1
2
VGA
L
R
AUDIO
OUT
AV
IN
TRIG
OUT
b
a
To change the size of the screen, just move the projector towards or away from the wall.
The size of the screen (b) is comprised between 50 and
100 inches depending on the projection distance (a), as
described in the following table.
10
Diagonal size (b)
(mm)
[inch]
Projection distance
(a)
(mm)
1270
[50]
108
2540
[100]
441
Installing or Changing the
batteries of the IR Remote
Control
DANGER!
Risk of Explosion with Incorrect Type of
Batteries
Only use the AAA type battery.
There is a risk of explosion if the incorrect battery type is used.
1 To access the battery, press to unlock the locking
mechanism (1) and slide out the battery compartment (2).
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 11 Jeudi, 12. février 2015 11:31 11
2 Insert the new batteries into the battery compartment with the positive and negative poles as shown.
Make sure the polarities(+ and -) are aligned correctly.
3 Push the battery compartment back into the
remote control until the locking mechanism
engages.
CAUTION!
• The improper use of batteries can lead
to overheating, explosion, risk of fire
and injury. Leaking batteries can possibly
damage the remote control.
• Never expose the remote control to
direct sunlight.
• Avoid deforming, dismantling or charging the batteries.
• Avoid exposure to open fire and water.
• Replace empty batteries immediately.
• Remove the battery from the remote
control if not in use for long periods of
time.
Notice
Normally the batteries will last for around
one year. If the remote control stops working,
please replace the batteries. If the device is
not used for a long time, take out the batteries. This will prevent leakage and possible
damage to the remote control.
The used batteries should be disposed of
according to the recycling regulations of your
country.
Using the Remote Control
The remote control can be used within an angle of 22.5
degrees and up to 10 meters from the device. When
using the remote control, no obstacle should be placed
between the remote control and remote sensor.
Installing or Changing the
batteries of the RF Remote
Control
DANGER!
Risk of Explosion with Incorrect Type of
Batteries
Only use the AAA type battery.
There is a risk of explosion if the incorrect battery type is used.
1 To access the battery, take an appropriate tool and
place it in the orifice as shown below, open the battery compartment.
1
PHILIPS
22,
5°
EPG
SOURC
3D
SMART
E SETTIN
GS
22,5°
FAVORIT
E
FORMA
T
MENU
TAB
INFO
OK
EXIT
RECALL
PAGE/C
H-
OPTION
S
PAGE/C
H+
1 .@
2
4 GHI
5 JKL
7 PQRS
SUBTIT
LE
ABC
8 TUV
0
DEF
MNO
3
6
9
WXYZ
TEXT
PHILIPS
Initial Operation
11
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 12 Jeudi, 12. février 2015 11:31 11
2 Press the black latch locking.
3 Lift the lever blue retention.
Notice
Normally the batteries will last for around
one year. If the remote control stops working,
please replace the batteries. If the device is
not used for a long time, take out the batteries. This will prevent leakage and possible
damage to the remote control.
The used batteries should be disposed of
according to the recycling regulations of your
country.
2
3
Placing the USB receiver RF
Remote Control (RF)
Your remote control is recognized by the device with
the supplied USB receiver connected to a rear USB
port.”.
4 Insert the new batteries into the battery compartment with the positive and negative poles as shown.
Make sure the polarities(+ and -) are aligned correctly.
4
Notice
Respect the direction of insertion, do not
force any case!
1 Take the USB receiver and insert it into a USB port
on the device.
5 Press the locking lever until you hear "CLICK" it
tells you that the closure is correct.
CLICK
5
6 Replace the battery cover in place and press down
to close.
12
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 13 Jeudi, 12. février 2015 11:31 11
2 Now do move your remote control right and left
arrow moves as you move.
Notice
Remote Control (RF) pairing
If the Screeneo does not react to RF remote
control commands, the remote control has to
be paired with the USB receiver again. For
renewing the pairing please connect the USB
receiver to a rear USB port of the Screeneo.
Then pressing the red and blue key on the
remote control together for 5 s to 10 s at the
same time.
2
Using the RF remote control
Your remote uses radio waves to communicate with
your device.
Notice
The range of your remote control is
15 meters in direct line.
1 To activate the RF remote control, position yourself
in front the camera. Touch and hold the OK button
until the pointer
on the screen appears.
1
Stand ye in the desired menu or setting and press
OK to access.
3 When you enter the text, return your RF remote
control and use the keyboard to enter your text.
3
Initial Operation
TEXT_
13
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 14 Jeudi, 12. février 2015 11:31 11
3D glasses
The 3D glasses are equipped with a battery. They have
to be charged before first use.
1 Take USB mini cable (supplied), connect the USB
mini on the 3D glasses and the another plug on a
USB port of the device.
Charging takes several hours and is complete when
the LED on the glasses is on green.
When the LED turns red, do a new charge.
Activate 3D glasses
1 Press the ON / OFF button on the top of the
glasses.
2 On the remote control, press the 3D button.
3 The 3D menu appears, select your choice and press
OK.
4 Press the ON/OFF button for one second and a half
on the 3D glasses .
3x
1.5 SEC
The LED flashes green three times and becomes
fixed. Your glasses are ready.
14
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 15 Jeudi, 12. février 2015 11:31 11
Initial Installation
ECO mode
1 To turn on the projector, push the POWER B button once.
2 Turn the device towards a suitable projection surface or wall. Note that the distance to the projection surface must be a minimum of 0.1 meter and a
maximum of 0.5 meter (see Setting up the Device,
page 4). Make sure the projector is in a secure position.
3 Use the focus wheel on the font of the device to
adjust the image sharpness.
4 The first time you turn on the device, you should
set the following settings.
Press shortly the B button on the panel control or on
the remote control to put the device in ECO mode.
To wake up the device, press shortly again on the
B button.
Setting up the Language
The device has already been installed. In order to
change the menu language, proceed as follows:
1 Use the navigation keys to select Settings.
Notice
During the first installation, use OK key to
validate your choice and continue to the next
step, and the ¿ key to return on the previous step.
5 Use the keys / to select the language and
confirm with OK.
6 Use the keys //À/Á to select the symbol
+ or - to set the date (day, month and year) and
confirm with .
7 Use the keys / to select the date format and
confirm with .
8 Use the keys / to select the time zone and
confirm with .
9 Use the keys //À/Á to select the symbol
+ or - to set the date (hour and minute) and confirm with .
10 Use the keys / to select the time format (12h
or 24h) and confirm with .
11 Use the keys / to select the location (Home
or Shop) and confirm with .
Home: for normal use.
Shop: when you choose this option, the projector
starts in demonstration mode. In this mode, the
projector automatically displays the pictures or videos stored in the internal memory in loop.
2
3
4
5
6
7
8
9
Confirm with .
Select Language/ Language with /.
Confirm with .
Select Menu Language with /.
Confirm with .
Select you desired language with /.
Confirm with .
Exit with u.
Notice
The demonstration mode can be activated or
deactivated on the menu Setting/Maintenance/Demo mode.
12 A message is displayed «Open User Manual?»,
use the keys À/Á for select Yes or No. Press
to continue.
The manual is displayed or the address web site
where the user manual can be downloaded.
Turning off the projector
Press the B button on the panel control of the device
or on the remote control more than 5 seconds.
Initial Operation
15
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 16 Jeudi, 12. février 2015 11:31 11
4 Connect to the Playback Device
Connecting to Devices with
HDMI Output
Connecting to a Computer
(VGA)
Use the HDMI cable to connect the projector to a computer, laptop or others devices.
Notice
Many laptops do not activate the external
video output automatically when you connect
a second display such as a projector. Check
your laptop's manual to find out how to activate the external video output.
Notice
Use any of the HDMI sockets to connect the
projector to a DVD player when a 3D signal
is broadcasted.
1 Switch the device on using the on/off key.
2 Connect the cable to the projector's HDMI
socket.
Use the VGA cable (not included) to connect the projector to a computer, laptop, or some PDAs. The projector supports the following resolutions: VGA/SVGA/
XGA. For best results, please check the best resolution.
PHILIPS
S/PDIF
OPTICAL
1
2
L
VGA
R
AUDIO
OUT
AV
IN
TRIG
OUT
PHILIPS
S/PDIF
OPTICAL
1
2
VGA
PHILIPS
VGA
L
R
AUDIO
OUT
AV
IN
TRIG
OUT
HDMI 3
HDMI 1 & HDM 2
3 Connect the cable to the HDMI socket of the playback device.
4 From the main menu, select HDMI 1,2 or 3
depending on the external device is connected.
1 Switch the device on using the on/off key.
2 Connect the VGA cable to the projector's VGA
socket.
3 Connect the VGA plug to the VGA socket of the
computer.
4 Adjust the computer's resolution to the correct
setting and switch the VGA signal to an external
monitor. The following resolutions are supported:
Resolution
Image
refresh rate
VGA
640 x 480
60 Hz
SVGA
800 x 600
60 Hz
XGA
1024 x 768
60 Hz
WXGA
1280 x 768
60 Hz
FULL HD
1920 x 1080
60 Hz
Notice
Screen Resolution
For best results, please check the best resolution.
5 From the main menu, select VGA.
16
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 17 Jeudi, 12. février 2015 11:31 11
Connecting Using an Audio/
Video (CVBS) Adapter
Cable
Use the projector's audio/video adapter cable (A/V
cable) (not included) to connect camcorders, DVD
players or digital cameras. The jacks for these devices
are yellow (video), red (audio right) and white (audio
left).
Connecting to a home
cinema amplifier
Use a S/PDIF optical cable (cable not provided) to connect the DIGITAL AUDIO output on the projector to
the input of your home cinema amplifier.
For example, to show digital channels in DTS or
DOLBY DIGITAL quality sound.
PHILIPS
PHILIPS
S/PDIF
OPTICAL
1
S/PDIF
OPTICAL
2
L
VGA
1
2
VGA
L
R
AUDIO
OUT
AV
IN
R
TRIG
OUT
AV
IN
AUDIO
OUT
S/PDIF
OPTICAL
AV
IN
TRIG
OUT
1 Connect the A/V adapter to the socket of the
projector.
2 Connect the video device's audio/video sockets to
the A/V cable using a conventional composite video
(RCA) cable.
3 From the main menu, select AV-in.
Connecting to mobile multimedia devices
Some video devices (e.g.: pocket multimedia players, ...)
require specific connection cables. There are either
supplied with the device or acquired from the manufacturer of the multimedia device. Please note that only the
original cables from the device manufacturer may function.
Connecting to a Hi-Fi unit
It is possible to use an analog audio connection, just
connect the right and left audio outputs of the Projector
to the auxiliary input of your Hi-Fi system (cable not
provided).
PHILIPS
S/PDIF
OPTICAL
1
2
VGA
PHILIPS
L
R
AUDIO
OUT
AV
IN
TRIG
OUT
S/PDIF
OPTICAL
1
2
VGA
L
R
AV
IN
AUDIO
OUT
AV
IN
TRIG
OUT
AUDIO
OUT
Notice
Switching to the Multimedia Device Signal Output
See the multimedia device instruction manual
to find out how to switch the signal output to
this jack.
Connect to the Playback Device
17
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 18 Jeudi, 12. février 2015 11:31 11
Connecting the headphones
1 Before connecting the headphones, turn down the
volume on the device.
2 Connect the headphones to the projector's headphone slot. The device speakers deactivate automatically when the headphones are connected.
PHILIPS
3 After connecting the headphones, increase the volume to a comfortable level.
DANGER!
Danger of Hearing Damage
Do not use the device over a longer time at
high volume – especially when using headphones. This could lead to the risks of hearing
damage. Before connecting the headphones,
turn down the volume on the device. After
connecting the headphones, increase the volume to a comfortable level.
WiFiDisplay (Miracast)
7 Connect the external device (smartphone or tablet) to the same WiFi network that the projector.
8 Select on the WifiDisplay application of the external device the name of the projector connection (in
the example Screeneo_5f31).
9 Connect the external device (smartphone or tablet) to the projector, it will show up connecting.
10 In the WifiDisplay application of the projector, it
will show up the message Invitation to connect,
Decline or Accept, select Accept.
Directly Connecting
Projector to Computer using
WLAN (WiFi Streaming)
With the ScreeneoWLink software you can connect the
projector to a computer or a laptop over your wireless
network. For this purpose, both devices must be connected to the same wireless network.
1 Intall the ScreeneoWlink software on your computer. The ScreeneoWlink software is stored in the
Download folder, you can get it by SD card or USB
disk from the address: APPs_explorer_internal
flash_Download.
2 Connect the device with the wireless network (see
also Wireless Network (WLAN), page 22).
3 Start ScreeneoWLink (Viewer) on your computer.
4 Click the ScreeneoWLink icon in the notification
area and start the manager window.
You are now able to search for projectors in the network (Search WIFI projector) and start the projection
(Start projection).
ScreeneoWLink software
Notice
Only the Miracast-certified devices can be
used with this function.
1 Switch the device on using the on/off key.
2 After the initial screen the main menu appears.
Notice
The projector must be connected to a WiFi
network.
3
4
5
6
Use the navigation keys to select APPs.
Confirm with .
Use the navigation keys to select WifiDisplay.
Confirm with .
It allows to connect the projector to a desktop PC or
laptop via the wireless or wired network and to use the
Screeneo as computer screen.
For this, both devices must be connected to the same
wireless or wired network.
Screeneo firmware version 1.20 must be installed on
your projector.
Check the version of firmware installed on your projector by going to the Settings menu > Maintenance >
Firmware version.
If the Screeneo firmware version is 1.20, refer to paragraph Install the ScreeneoWLink software on my computer.
If the Screeneo firmware version is less than 1.20, refer
to paragraph Update the software in my projector.
Notice
The name used to identify the projector can
be modified in the Setting menu.
18
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 19 Jeudi, 12. février 2015 11:31 11
Update the software in my
projector
20 The device turns off and on again. After around 5
minutes the Language Selection screen appears. The
firmware update is now completed.
You can find the Screeneo firmware version on the site
« Philips »: www.philips.com/screeneo for loading the
file proceed as following
You must download the file on SD-card formatted
FAT16 or FAT32, on USB stick or on USB digital support in order to update your Screeneo.
Get yourself a suitable digital media and insert it into
your computer.
1 Launch an Internet browser, in the address bar, type
the address: www.philips.com/screeneo.
2 Choose your country and click on the language.
3 Click on View All 4 Products for select your model.
4 Select exactly your model with mouse.
5 In the new screen, research Support and click on.
6 The "Screeneo Smart LED projector" screen
appears. In the "Software & drivers" select your
language and click Download file.
Notice
Notice
The file on the website is a zip file. It has to be
unpacked and put on the root folder of the
SD-card or USB-stick.
7 Depending on the browser used, save the file in the
root of your digital media.
8 On the Screeneo projector, to check that it is turned
off (OFF).
9 Remove the digital media on your computer and
insert it into the port of Screeneo for your digital
media.
10
DANGER!
Inserting the digital media!
Never pull out the digital media while the
device is accessing it. This could cause data
to be damaged or lost.
Switch the device off in order to make sure
that the device does not access the
memory card.
11 Long press the ON/OFF button on the projector to
turn it on.
12 After the initial screen, the main menu appears. Use
the navigation keys to select Settings.
13 Confirm with OK.
14 Use / to select Maintenance.
15 Confirm with OK.
16 Use / to select Firmware Update.
17 Confirm with OK.
18 Use / to select Install.
19 Confirm with OK.
Connect to the Playback Device
If an error occurs during the firmware update
process retry the procedure or contact your
dealer.
Copy the software on digital
media (eg USB-stick)
Use the USB ports on the projector to insert digital
media.
1 Use / to select APPs.
2 Confirm with OK.
3 Use / to select Explorer.
4 Confirm with OK.
5 Use / to select Internal Flash.
6 Confirm with OK.
7 Use to select Download.
8 ScreeneoWLink_Setup.exe file appears in the main
window.
9 Press long OK button on the remote control.
10 Use / to select Copy.
11 Confirm with OK.
12 Use //À/Á you move on to the digital
media that you have connected.
13 Confirm with OK.
14 Press long OK button on the remote control.
15 Use / to select Paste.
16 Confirm with OK.
17 ScreeneoWLink_Setup.exe file is copied to the digital media. Wait that it appears in the browser window before removing the digital media projector.
Install the ScreeneoWLink
software on my computer
1 Insert the digital media containing the ScreeneoWLink_Setup.exe file on an appropriate port on
your computer.
2 On desktop PC or laptop, select the digital media
containing the file and double click the executable.
3 Follow the instructions that appear on the screen.
4 Agree to have the ScreeneWLink icon on your desktop.
5 When installation is complete, restart your computer.
19
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 20 Jeudi, 12. février 2015 11:31 11
Link your projector and computer
with WiFi
4 Click Search.
Both devices must be connected to the same access
point, no other network connection must be activated.
As a precaution, note the name and the key to protection of your access point.
On the Screeneo,
Use / to select Settings.
Confirm with OK.
Using / select Wireless and Networks.
Confirm with OK.
Using / select WIFI.
Confirm with OK.
Using / select the desired wireless network.
Confirm with OK.
If your network is protected by a password, a window appears. Select the input field with the navigation buttons on the remote and press OK.
A virtual keyboard appears, using the navigation keys
on the remote control, witch a mouse or external
keyboard.
Enter your password.
10 Click Connect.
1
2
3
4
5
6
7
8
9
5 Select and click on the Screeneo where you want to
connect.
6 If necessary, enter password of acces point selected.
You can enjoy the Screeneo as screen for your PC.
Start ScreeneoWLink on your PC
1 Open the Start menu. Locate and open the ScreeneoWLink tab. Click on ScreeneoWLink or double
click on ScreeneoWLink icon of your desktop.
2 The ScreeneoWLink V1.2 software opens on the
screen.
3 Stand on the projector image with the magnifying
glass and click it.
20
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 21 Jeudi, 12. février 2015 11:31 11
5 Memory
Inserting a Memory Card
Connecting USB Storage
Medium
PHILIP
S
PHILIP
S
1 Insert a memory card with the contacts facing downwards into the / slot at the back of the
device. Your device supports the following memory
cards: SD/SDHC/SDXC/MMC.
2 Insert the memory card into the slot until it snaps
into position.
DANGER!
Inserting a Memory Card!
Never pull out the memory card while the
device is accessing it. This could cause data
to be damaged or lost.
Switch the device off in order to make sure
that the device does not access the memory card.
3 Press lightly on the memory card to remove it.
4 The memory card is ejected.
Memory
PHILIPS
S/PDIF
OPTICAL
1
2
VGA
L
R
AUDIO
OUT
AV
IN
TRIG
OUT
1 Connect the USB storage medium to one USB port
of the device.
DANGER!
Inserting a Memory Card!
Never pull out the memory card while the
device is accessing it. This could cause data
to be damaged or lost.
Switch the device off in order to make sure
that the device does not access the memory card.
21
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 22 Jeudi, 12. février 2015 11:31 11
6 Network
The projector can be connected to the network by a
network hard-wired cable or through a wireless (Wi-Fi)
connection.
Use the procedure below appropriate to the type of
connection you want.
LAN Network
Notice
Connection!
The LAN connection takes priority over the
Wi-Fi connection.
Connecting to the LAN network
1 Connect one end of a LAN cable (not supplied) to
the ETHERNET port of your projector.
PHILIPS
S/PDIF
OPTICAL
1
2
VGA
L
R
AUDIO
OUT
AV
IN
TRIG
OUT
2 Connect the other end of the LAN cable to the
network.
3 Configure the LAN network settings in manual or
automatic configuration.
Automatic configuration
The automatic configuration of the local network settings may be considered, if your local network features
a DHCP or BOOTP server that can dynamically assign
addresses to the peripheral devices present on the
LAN.
To automatically configure the local network settings:
1 Switch the device on using the on/off key.
2 After the initial screen, the main menu appears.
3 Use the navigation keys to select Settings.
4 Confirm with .
5 Using / select Wireless and Networks.
6 Confirm with .
7 Using / select Lan.
22
8 Confirm with .
9 Using / select On.
10 Confirm with .
11 Using / select Advanced.
12 Confirm with .
13 Using / select Network address.
14 Confirm with .
15 Check that Automatic is selected.
Manual configuration
To configure your projector manually, you should
obtain the usual information used to set a peripheral
device (IP address, sub-network mask, network and
gateway address).
To configure the local network setting manually:
1 Switch the device on using the on/off key.
2 After the initial screen the main menu appears.
3 Use the navigation keys to select Settings.
4 Confirm with .
5 Using / select Wireless and Networks.
6 Confirm with .
7 Using / select Lan.
8 Confirm with .
9 Using / select On.
10 Confirm with .
11 Using / select Advanced.
12 Confirm with .
13 Using / select Network address.
14 Confirm with .
15 Using / select Use static IP.
16 Confirm with .
17 Enter the settings IP-Address, Gateway, Netmask, DNS1 and DNS2.
18 Confirm with .
Wireless Network (WLAN)
In a wireless network (Wireless Local Area Network,
WLAN) at least two computers, printers or other additional devices communicate with each other over radio
waves (high frequency waves). Data transmission in the
radio network is based on the standards 802.11a,
802.11b, 802.11g and 802.11n.
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 23 Jeudi, 12. février 2015 11:31 11
DANGER!
Information on Using WLAN!
The functioning of security systems, medical
equipment or sensitive devices can be disrupted by the transmission power of the
device. Observe any usage regulations (or
restrictions) in the vicinity of such equipment.
The use of this device can affect the operation
of insufficiently shielded medical devices and
hearing aids and pacemakers through the
release of high frequency radiation. Also consult a doctor or the manufacturer of the medical device to establish whether these are sufficiently shielded from external high frequency
radiation.
Setting up a Wireless
Network (WLAN)
1 Switch the device on using the on/off key.
2 After the initial screen the main menu appears.
Infrastructure Wireless Network
In an infrastructure network, multiple devices communicate via a central access point (gateway, router). All
data are sent to the access point (gateway, router) and
distributed from there.
Switching Wireless
Networking (WLAN) on/off
Wireless networking is deactivated by default. You have
the option of turning this function on.
1 Switch the device on using the on/off key.
2 After the initial screen the main menu appears.
3 Use the navigation keys to select Settings.
4 Confirm with .
5 Using / select Wireless and Networks.
6 Confirm with .
7 Using / select WIFI Selection.
8 Confirm with .
9 Use / to select the desired wireless network.
10 Confirm with .
11 If your wireless network is password protected, an
input window appears. Select the input field (see
Navigation for setting menu, page 8) using the navigation keys of the remote control and press OK.
12 Enter the password with the virtual keyboard using
the navigation keys of the remote control or with
an external keyboard.
13 Click on Connect.
The ¿ key takes you one step back in the menu.
Setting up a Wireless
Network (WLAN) using the
Wizard
3 Use the navigation keys to select Settings.
4 Confirm with .
5 Using / select Wireless and Networks.
6 Confirm with .
7 Using / select WIFI.
8 Confirm with .
9 Modify the settings with /.
10 Confirm with .
The ¿ key takes you one step back in the menu.
Network
You can integrate your device very quickly and easily
into an existing wireless network using Wi-Fi Protected
Setup (WPS) or using a wireless network scan. Using
WPS, all important settings like network name (SSID)
are automatically configured and the connection protected with secure WPA Encryption.
Using Wi-Fi Protected Set-up
(WPS)
Using Wi-Fi Protected Setup (WPS), you can integrate
your device into an existing wireless network in two different ways very quickly and easily. You can activate the
login with a pin code or using Push Button Configuration (PBC), if your access point (Access Point, Router)
supports this method.
23
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 24 Jeudi, 12. février 2015 11:31 11
Using WPS with Push Button
Configuration (PBC)
Wifi Hotspot
Notice
1 Switch the device on using the on/off key.
2 After the initial screen the main menu appears.
Important!
The projector can work as an access point, if
only a wired lan network is installed in the
location of use.
Use the portable Wi-Fi hotspot to share the device’s
network connection with computers or other devices
through the Wi-Fi network.
Notice
Connection!
When the WiFi hotspot mode is activated, it
takes priority over the other connections.
3
4
5
6
7
8
9
Use the navigation keys to select Settings.
Confirm with .
Using / select Wireless and Networks.
Confirm with .
Using / select WIFI Selection.
Confirm with .
Use / to select the desired wireless network..
10 Confirm with .
11 Activate Push Button Configuration on the WLAN
access point. The WLAN access point and device
connect automatically and create a WPA protected
connection.
Activating WiFi hotspot
1 Switch the device on using the on/off key.
2 After the initial screen, the main menu appears.
3 Use the navigation keys to select Settings.
4 Confirm with .
5 Using / select Wireless and Networks.
6 Confirm with .
7 Using / select WiFi Hotspot.
8 Confirm with .
9 Using / select Portable WiFi Hotspot.
10 Confirm with .
11 Using / select On.
12 Confirm with .
The projector is now visible by other Wifi devices.
24
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 25 Jeudi, 12. février 2015 11:31 11
Setting up a WiFI hotspot
To modify the WiFi hotspot name and define the security level.
1 Switch the device on using the on/off key.
2 After the initial screen the main menu appears.
3 Use the navigation keys to select Settings.
Digital Living Network
Alliance (DLNA)
This device supports Digital Living Network Alliance
(DLNA). Using this standard you can quickly interconnect your multimedia devices.
Switching DLNA on and off
The DLNA function is switched on by default. You have
the option of turning this function off.
1 Switch the device on using the on/off key.
2 After the initial screen the main menu appears.
4 Confirm with .
5 Using / select Wireless and Networks.
6 Confirm with .
7 Using / select WiFi Hotspot.
8 Confirm with .
9 Using / select Setup WiFi hotspot.
10 Confirm with .
11 To modify the settings, use / keys to select
the desired parameter.
Item
Description
Network SSID
Name of the WiFi hotspot.
This is the name used to identify your projector when it is
detected by another WiFi device.
To modify the name, select the
field and press . With the
keyboard, enter the new
name.
Security
Select among the 3 levels of security.
• Open (without security)
• WPA PSK
• WPA2 PSK
Password
Select the field and press .
With the keyboard, enter the
new password.
Show password
Check the box to display the
password.
3 Use the navigation keys to select Settings.
4 Confirm with .
5 Using / select Wireless and Networks.
6 Confirm with .
7 Using / select DLNA Sharing.
8 Confirm with .
9 Modify the settings with /.
10 Confirm with .
The ¿ key takes you one step back in the menu.
Play Media Using DLNA
If DLNA enabled devices are located in the connected
network, then you can access them in media playback
and file management (see Media Playback, page 28).
DLNA Control
You can control the projector using another device (e.g.
a smartphone) using DLNA. To do this, see the instruction manual for the device in question.
12 Using / select Save.
13 Confirm with .
Network
25
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 26 Jeudi, 12. février 2015 11:31 11
7 Bluetooth
Activating the Bluetooth
connection
1 Switch the device on using the on/off key.
2 After the initial screen, the main menu appears.
9 Using / select the desired setting.
10 Confirm with .
11 Modify the desired settings.
Menu
Description
Select device
The list shows all paired devices.
Paired device
To unconnect or unpair the
paired device.
Bluetooth speaker
The projector can be used as Bluetooth speaker. In this
mode, you can play music from smartphones or tablets.
The projector can only connect to, and play audio from
one device at a time.
3 Use the navigation keys to select Settings.
4 Confirm with .
5 Using / select Wireless and Networks.
6 Confirm with .
7 Using / select Bluetooth.
8 Confirm with .
9 Use / to select on.
10 Confirm with .
The projector is now visible for the near external Bluetooth devices.
Activating Bluetooth speaker
Notice
Bluetooth speaker connection!
Depending on the model of your device, the
bluetooth speaker can be activated from the
main menu (BT Speaker icon) or from the
APPs menu.
1 Switch the device on using the on/off key.
2 After the initial screen, the main menu appears.
Setting up Bluetooth
parameters
1 Switch the device on using the on/off key.
2 After the initial screen, the main menu appears.
3 Depending on model, use the navigation keys to
select BT Speaker or APPs>BT Speaker.
Notice
3
4
5
6
7
8
26
Use the navigation keys to select Settings.
Confirm with .
Using / select Wireless and Networks.
Confirm with .
Using / select Bluetooth.
Confirm with .
Remote control
You can also use the SOURCE or
OPTIONS key of the remote control.
Press the SOURCE key and select BT
Speaker or press OPTIONS key then
select SOURCE and BT Speaker.
4 Confirm with OK.
5 Press the Red key to power on the speaker.
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 27 Jeudi, 12. février 2015 11:31 11
6 Press the Green key to make the speaker discoverable during 60 seconds.
7 On your external device, activate the Bluetooth
connection and select the speaker name from the
list.
When the device is connected, his name is displayed on the top of the screen.
8 Press the Green key to play music.
During music playback, the following actions are
available:
Red key: To stop the connection.
Green key: To make a pause.
Yellow key: To play the previous music.
Blue key: To play the next music.
Changing the name of the
Bluetooth speaker connection
This is the name used to identify your projector when
it is detected by another Bluetooth® device.
1 Switch the device on using the on/off key.
2 After the initial screen, the main menu appears.
3 Depending on model, use the navigation keys to
select BT Speaker or APPs>BT Speaker.
4 Press the Yellow key to rename the connection.
5 Use the keyboard to enter the new name.
6 Press OK to confirm.
Bluetooth
27
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 28 Jeudi, 12. février 2015 11:31 11
8 Media Playback
Notice
Navigation Keys
All the keys shown are buttons on the remote
control.
Keys
Action
Green key of the
remote control
Allows to set the slide show
parameters for picture files.
or
Allows to set the shuffle
mode for music files:
Notice
Best Settings for Optimal Use
Read the informations on the best settings in
the chapter settings (see Settings, page 36) for
optimal use of your device.
Navigating in the media
Playback
To navigate in the memory media, use the following
keys:
Keys
Action
or To select folders or files in the
displayed list.
Á or For directories, goes one level
down.
For files, starts the selected
media file.
À or ¿
Goes one level up in the directory structure.
u
Exits to main screen.
Red key of the remote control
Allows to set the repeat
mode for movie and music
files:
28
•
: Play mode deactivate (greyed).
•
: Play only the
selected movie in loop.
•
: Play all movies in
the selected directory
in loop.
•
: Play all movies in
the media in loop.
•
: Shuffle mode
deactivate (greyed).
•
: Shuffle mode activate.
Yellow key of the
remote control
Allows to display the pictures
as miniatures or in a list.
Blue key of the remote control
Allows to delete the selected
file.
In order to optimize the navigation, you can select a file
type on the list:
•
FOLDERS to view all files (photo, audio
and video).
•
MOVIES to view videos files only.
•
PICTURES to view photo files only.
•
MUSIC to view audio files only.
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 29 Jeudi, 12. février 2015 11:31 11
Video playback
Supported file formats
7 Use / to select the video file that you wish to
play.
Notice
Supported file formats are *.avi, *.mov, *.mp4, *.mkv,
*.flv, *.ts, *.m2ts, *.3gp.
Video Playback (USB/SD Card/
Internal Memory/DLNA)
1 Switch the device on using the on/off key.
2 The main menu appears.
Displaying Video Files
Only those videos that are compatible
with the projector will be displayed.
8 Press or Á to start playback.
9 Press ¿ to end the slide show and return to the
overview.
10 When you press ¿ again, you will return to the
main menu.
Notice
Navigation During Playback
Review / forward: Press :/; on the
remote control.
Press T to stop or continue playback.
3 Use the navigation keys to select the desired media
(USB, SD-card or DLNA):
Memory
Internal memory or SD card can be selected.
USB
- If only one USB key is connected the explorer
shows only the content of the USB.
- If more than one USB memory is connected,
select the desired USB memory first.
DLNA
The explorer searches for servers and shows them
in a list. Select the desired DLNA server.
4 Confirm with .
The content of selected media is displayed.
5 To only display the movies content, select Movie
using the keys /on the left of the screen.
6 Confirm with .
During playback you can adjust the volume using the
keys
/
or À/Á on the remote control. Press
or
repeatedly to shut off the volume completely.
Photo Playback
Supported file formats
Supported file formats are JPEG, BMP, PNG and GIF.
Photo Playback (USB/SD Card/
Internal Memory/DLNA)
1 Switch the device on using the on/off key.
2 The main menu appears.
Notice
The use of color keys
The Red key allows to set the repeat mode:
•
: Play mode deactivate (greyed).
•
: Play only the selected movie in
loop.
•
: Play all movies in the selected
directory in loop.
•
: Play all movies in the media in loop.
The Blue key alows to delete the selected
file.
Media Playback
3 Use the navigation keys to select the desired media
(USB, SD-card or DLNA):
SD-card
Internal memory or SD card can be selected!
USB
- If only one USB key is connected the explorer
shows only the content of the USB.
- If more than one USB memory is connected,
select the desired USB memory first.
DLNA
29
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 30 Jeudi, 12. février 2015 11:31 11
The explorer searches for servers and shows them
in a list. Select the desired DLNA server.
4 Confirm with .
The content of selected media is displayed.
5 To only display the picture content, select Picture
using the keys /on the left of the screen and
confirm with .
Notice
The use of color keys
The Green key allows to set the slide show
parameters.
The Yellow key allows to display the pictures
as miniatures or in a list.
The Blue key allows to delete the selected
file.
6 The list of photos are displayed on the screen as an
overview.
Notice
Many Photos on the Memory Card or
the USB Medium
If there are a lot of photos on the memory
card or the USB storage medium it can
take a moment before the overview
appears.
7 Use À/Á or / to select the image that you
want to start the slide show with.
8 Press Green key to start the slide show.
Notice
The slide show can be started with the OK
key if the parameters have already been
set up.
Slide Show with Background
Sound
1 During the slide show, press to display the menu
bar on the bottom of the screen.
2 Using À/Á select Ó.
3 Confirm with .
4 Use / to select the file that you wish to play.
Notice
Storage Location
Only files from the internal memory/Memory Card/USB Storage Medium can be
played.
5 To start the background sound confirm with .
6 Adjust the volume level with the volume keys on
the remote control.
7 If no input is made, the menu bar is hidden after 5
seconds.
Zoom and rotate functions
During the slide show, press OK key to display the contextual menu.
To perform a zoom, use the navigation keys to select
the
symbol then press OK.
To rotate a picture, use the navigation keys to select the
symbol then press OK to rotate the picture 90°
clockwise.
Press ¿ return to the slide show.
9 To modify the settings, use / keys to select
the desired parameter.
Item
Description
Time per slide
To modify the photo display
frequency.
Off, 0, 2, 5, 10, 20, 30 and 60s
Repeat
Off, Directory or All
Slide transition
To modify the type of transition from one photo to another (random or by theme).
Slideshow order
Random or by order
10 Press Green key to start the slide show.
11 Press to pause the slide show.
12 Press ¿ to end the slide show and return to the
overview.
13 When you press u, you will return to the main
menu.
30
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 31 Jeudi, 12. février 2015 11:31 11
Music Playback
5 To only display the music content, select Music
using the keys /on the left of the screen and
confirm with .
Notice
Notice
Switch off the Image Playback
You can switch off the screen while playing
music in order to save power by a long press
on the
The use of color keys
The Red key allows to set the repeat mode:
key.
Supported file formats
•
: Play mode deactivate (greyed).
•
: Play only the selected music in
loop.
•
: Play all musics in the selected
directory in loop.
•
: Play all musics in the media in loop.
Supported file formats are MP3 and WAV.
Music Playback (USB/SD Card/
Internal Memory/DLNA)
1 Switch the device on using the on/off key.
2 The main menu appears.
The Green key allows to set the shuffle
mode:
•
: Shuffle mode deactivate (greyed).
•
: Shuffle mode activate.
The Blue key allows to delete the selected
file.
6 Use / to select the file that you wish to play.
7 Press to start playback.
8 Press T to stop or continue playback.
Notice
3 Use the navigation keys to select the desired media
(USB, SD-card or DLNA):
SD-card
Internal memory or SD card can be selected!
USB
- If only one USB key is connected the explorer
shows only the content of the USB.
- If more than one USB memory is connected,
select the desired USB memory first.
DLNA
The explorer searches for servers and shows them
in a list. Select the desired DLNA server.
4 Confirm with .
The content of selected media is displayed.
Media Playback
Navigating when Image Playback is
Switched off
Press / to skip to the previous or
next song.
Press T to stop or continue playback.
Press ¿ to return to the selection.
During playback you can adjust the volume using the
keys
/
or À/Á on the remote control. Press
or
repeatedly to shut off the volume completely.
31
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 32 Jeudi, 12. février 2015 11:31 11
Managing Files
Delete Files
You can delete files from the internal memory, the connected USB storage medium or the memory card.
1 Switch the device on using the on/off key.
2 The main menu appears.
3 Use the navigation keys to select the desired media
(USB, Memory or DLNA).
4 Confirm with .
5 Use / to select the file that you want to
delete.
6 Press the Blue key on the remote control to
delete the file.
7 Confirm with .
Notice
Error
If errors occur during the deletion process, make sure that the storage medium is
not write-protected.
32
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 33 Jeudi, 12. février 2015 11:31 11
9 Digital TV Playback
(Depending on model)
Connecting the Aerial
First Playback
Notice
Notice
Aerial Size and Orientation
In some regions it is necessary to connect a
larger aerial in order to grant the reception.
In some countries it is necessary to point the
aerial horizontally in order to grant the reception.
1 Connect the aerial to the aerial socket.
Navigation Keys
All the keys shown are buttons on the remote
control.
When the DVB-T function is first started, the automatic
channel search must be started.
1 Switch the device on using the on/off key.
2 The main menu appears.
PHILIPS
S/PDIF
OPTICAL
1
2
VGA
L
R
AUDIO
OUT
AV
IN
TRIG
OUT
3 Connect the aerial (see Connecting the Aerial,
page 33).
4 Use the navigation keys to select TV.
5 Confirm with .
6 Use / to highlight a setting and use the À/
Á to select a value.
- Select the country.
- Select the level of the parental control.
- Enter the PIN code for channel lock or parental
control. Enter the code with 4 digits (0000 is not
accepted) and enter again the same code to confirm.
7 Press OK to confirm the settings and continue the
installation.
The channel search starts automatically.
8 At the end of the search, press .
Your TV is now set. You can start watching and enjoying all your channels.
Digital TV Playback (Depending on model)
33
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 34 Jeudi, 12. février 2015 11:31 11
Television
Notice
Navigation Keys
All the keys shown are buttons on the remote
control.
1 Switch the device on using the on/off key.
2 The main menu appears.
3 Use the navigation keys to select TV.
4 Confirm with OK.
5 The last viewed channel is played. Change the channel using keys CH+/CH-, / or enter directly
the number with the keypad.
Notice
Displaying Channel Information
When changing channel, channel information is displayed on the bottom projection
edge. The information bar is hidden after 5
seconds.
6 Press u to end playback and return to the main
menu.
During playback you can adjust the volume using the
keys
/
or À/Á on the remote control. Press
or
repeatedly to shut off the volume completely.
Modifying the DVB-T
settings
To modify DVB-T settings, press the Menu key on the
remote control. Main menus are:
Edit channels: To display and modify the channel and
radio lists.
Installation: To launch an automatic or a manual
search for channels.
System Setup: To modify the parental lock settings,
the display settings and the favorite settings.
34
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 35 Jeudi, 12. février 2015 11:31 11
10 Android
Your projector uses the Android operating system.
Starting Android Apps
1 Switch the device on using the on/off key.
2 After the initial screen the main menu appears.
6 Confirm with OK.
7 Use the navigation keys to select ApkInstaller.
8 Confirm with OK.
9 Use the navigation keys to select Install.
10 Confirm with OK.
11 Navigate to the memory card and select the APK
package you want to install.
12 Press OK to execute the installation package.
13 The APK package is installed.
3 Use the navigation keys to select APPs.
4 Confirm with OK.
Exiting Android
Press the u key to return to the main menu.
Installing Android-Apps
CAUTION!
Trusted Sources!
Apps from third party sources may be malicious. Only use installation packets from
trusted sources.
You can install other apps. Use the APK installation
packets, proceed as follows:
1 Download the package APK and save it onto a memory card or USB-stick.
2 Insert the memory card into the device (see Inserting a Memory Card, page 21).
3 Switch the device on using the on/off key.
4 After the initial screen the main menu appears.
5 Use the navigation keys to select APPs
Android
35
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 36 Jeudi, 12. février 2015 11:31 11
11 Settings
1 Switch the device on using the on/off key.
2 After the initial screen the main menu appears.
3 Use the navigation keys to select Settings.
4 Confirm with OK.
5 Use / to select from the following settings.
6 Confirm with OK.
7 Modify the settings using OK, /,
8 Confirm with OK.
The ¿ key takes you one step back in the menu.
Overview of the Menu
Functions
Wireless and Network
WiFi – switching the wireless network (WLAN) off
and on.
Network Selection – select the wireless network
with which the device is to connect.
WiFi Hot Spot – activate and deactivate WLAN
tethering.
LAN – switching the LAN network (LAN) off and
on.
Advanced – (LAN mode only) check the Network
actual IP address or change the address by inputting
new address. You can also select Automatic or
Use static IP
DLNA Sharing – switching DLNA off and on.
Bluetooth – switching the Bluetooth connection off
and on.
Image settings
3D – set the picture modes with 2D/3D options.
Keystone – use / to set the keystone.
Fit Screen – use / to select the screen mode
to adjust the size of your screen.
Projection mode
Front – normal projection; the device is located
in front of the projection surface/screen
Rear – rear projection; the device is located
behind the projection surface; the image is
reflected horizontally.
36
Front Ceiling – the device is hanging from the
ceiling in an upside-down position; the image is
rotated by 180 degrees.
Rear ceiling – the device is located behind the
projection surface, hanging from the ceiling in an
upside-down position; the image is rotated by
180 degrees and reflected horizontally.
Wall color correction – colour correction of the
projected image to adjust to coloured projection
surfaces
Smart Settings – select predefined settings for
brightness / contrast / colour saturation. If you modify these settings, the setting is switched to Manual.
Brightness – use / to adjust the brightness
and press OK to confirm.
Contrast – use / to adjust the contrast and
press OK to confirm.
Advanced
Colour temperature – set to Warm to enhance
hotter colors such as red, or set to Cool to
make picture bluish.
Dynamic contrast – adjusts the contrast to
keep it at the best level according to the brightness of the screen.
Color space – to convert the color space setting to another standard.
Gamma – adjusts the gamma correction
according to the type of the projected image.
Manual colors RGB – manually adjust the hue, saturation and brightness of colors in RGB mode. Use
//À/Á to adjust the colors according to
your needs.
Manual colors CMY – manually adjust the hue, saturation and brightness of colors in CMY mode. Use
//À/Á to adjust the colors according to
your needs.
Reset – valid manual modifications of colors RGB
and CMY.
Sound Settings:
Volume – adjust the volume
Deep Bass – switching the deep bass on and off
Wide sound – switching the wide sound on and off
Equalizer – select the equalizer mode
Smart volume – turn on/off the volume level automatic control function
Key beep – turn key tones on and off
Speaker – switching the speaker on and off
System settings
Date and time – set date and time
Android Settings – set Android system
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 37 Jeudi, 12. février 2015 11:31 11
Sleep mode – With this function, the projector
automatically goes to ECO mode after a specified
period of time or at the end of a movie.
Auto Power Down (APD) – turn on/off the auto
power down.
The default setting is depending on the choice of:
- shop mode: APD off,
- dome mode on: APD off,
- home mode: APD on.
When the parameter is switched on, it works like
this:
- it should go into off mode after 3 hours.
If a video is displayed, the APD should take place 3h
after last user action, meaning that a pop-up will
appear after 2h58 for 2 minutes, indicating that the
product will go into off mode.
HDMI name – select this item to change the HDMI
names. Name that appears on the main screen.
Language/Language
Menu language – use / to select the desired
language and press OK to confirm.
Soundtrack – use / to select the desired language and press OK to confirm.
Sub Title – use / to select the desired language and press OK to confirm.
Maintenance
Reset settings – Reset settings to factory defaults.
Firmware Update – Update Firmware
Information – Display free space in the internal
memory and information on the device (Capacity: /
Free space: / Firmware version: / Device name: /
Model:)
Demo mode – switching demo mode on and off. In
this mode, Screeneo is continuously displayed on
the screen and video and/or audio files placed in
internal memory are read directly.
Settings
37
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 38 Jeudi, 12. février 2015 11:31 11
12 Service
Cleaning
DANGER!
Instructions for Cleaning!
Use a soft, lint-free cloth. Never use liquid or
easily flammable cleansers (sprays, abrasives,
polishes, alcohol, etc.). Do not allow any
moisture to reach the interior of the device.
Do not spray the device with any cleaning fluids.
Wipe over the surfaces gently. Be careful that
you do not scratch the surfaces.
Cleaning the Lens
12 The device turns off and on again. After around 5
minutes the Language Selection screen appears.
The firmware update is now completed.
DANGER!
Inserting a Memory Card!
Never pull out the memory card while the
device is accessing it. This could cause data
to be damaged or lost.
Notice
If an error occurs during the firmware update
process retry the procedure or contact your
dealer.
Use a brush or lens cleaning paper for cleaning the lens
of the projector.
DANGER!
Do not use any Liquid Cleaning Agents
Do not use any liquid cleaning agents for
cleaning the lens, to avoid damaging the coating film on the lens.
Device Overheated
A overheat symbol appears if the device is overheated.
Update Firmware with
Memory Card
1 Use SD memory card in the file system FAT16 or
FAT32.
DANGER!
All Data will be Deleted!
This procedure erases all your data that is
stored on the memory card.
2 Save the latest firmware update file to the root of
the memory card.
3 Insert the memory card (see Inserting a Memory
Card, page 21) and switch the device on.
4 Use the navigation keys to select Settings.
5 Confirm with à.
6 Use / to select Maintenance.
7 Confirm with à.
8 Use / to select Firmware Update.
9 Confirm with à.
10 Use / to select Install.
11 Confirm with à.
38
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 39 Jeudi, 12. février 2015 11:31 11
Troubleshooting
1 Switch the device off using the on/off key on the
panel control.
2 Wait at least ten seconds.
3 Switch the device on using the on/off key on the
panel control.
4 If the problem repeats, please contact our technical
customer service or your retailer.
Power Cycling
If a problem occurs that cannot be corrected with the
instructions in this user manual (see also the help
below), follow the steps given here.
Problems
Solutions
The projector cannot be switched on
•
Disconnect and Connect the power supply cable and
try again.
The projector cannot be switched off
•
Disconnect the power supply cable.
No sound
•
check that the speaker is activated (Settings /Sound
setting/Speaker).
•
Adjust the volume using the
remote control.
•
•
•
Check the cables to the external device
Set the volume on the external device
Only the original cables from the device manufacturer may function
No sound from DVB-T program or external HDMI out- •
put device.
Set the audio setting to Multichannel (Raw data) &
Stereo (PCM).
No sound when you connect your computer via HDMI
cable
•
Check that the sound is activated on the computer.
Video display problem when the source is a 3D signal
from a DVD player.
•
Check that the 3D mode is activated on the projector.
If the DVD player is connected to the projector via
HDMI, use any of the HDMI sockets.
No sound from the external connected device
•
Only the initial screen appears and not the image from
the external device
•
•
•
•
Only the initial screen appears and not the image from
the connected computer
•
•
Service
/
key on the
Check if the cables are connected to the right sockets.
Please check that the external device is switched on
Check if the video output of the external device is
switched on.
Check that the HDMI source selected on the user
interface corresponds to HDMI connector where
the external device is connected.
Please check that the VGA-output of the computer
is switched on.
Check if the resolution of the computer is set to
1280*800(for VGA connection) or 1080P(for HDMI
connection).
39
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 40 Jeudi, 12. février 2015 11:31 11
Problems
Solutions
The device turns itself off
•
•
•
The device changes from maximum level of brightness to •
minimum level of brightness when the device is connected over USB to play videos.
•
The device cannot connect with an Android device (for
example a mobile phone/smartphone with the Android
operating system) when connected via USB.
•
When the device is running for a long period of time,
the surface becomes hot and a warning symbol
appears on the projection (see Symbols in the Statusbar, page 9). The device automatically turns off when
it gets too hot. After the device has cooled down,
you can continue playback.
Check that the power cable is connected correctly.
Check the sleep mode status in the setting menu ().
When the sleep mode is activated, the device turn
off after the programmed duration.
When the environment temperature is too high, the
devices turns automatically from maximum level of
brightness to minimum level of brightness in order to
protect the high power LED.
Use the device with lower environment temperatures.
Deactivate the function „USB debugging“ in the settings menu of your Android device before connecting the Projector via USB; your Android device
should be recognized as USB storage medium.
Bad image or color quality when connecting with HDMI •
Use a high quality HDMI cable. Low quality cables
may cause signal distortions.
The device cannot read the SD card.
•
Check that the memory card is compatible (see the
list in the chapter Appendix).
The device cannot read the USB stick
•
•
The device does not support the exFAT file system.
Format the USB key in FAT format, then use it.
The TV icon doesn't appear while the DVB-T module is
installed.
•
Call the hot-line.
The projector does not react to remote control commands when using the RF remote control.
•
•
Check if the remote control batteries are new.
The remote control has to be paired with the USB
receiver again. For renewing the pairing please connect the USB receiver to a rear USB port of the
Screeneo. Then pressing the red and blue key on the
remote control together for 5 s to 10 s at the same
time.
40
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 41 Jeudi, 12. février 2015 11:31 11
13 Appendix
Technical Data
Accessories
Dimensions (L×H×W) .................... 287 × 148× 339 mm
Weight ........................................................................... 5,3 kg
Recommended Ambient......................................5 – 35 ºC
Relative Humidity ................15 – 85 % (non-condensing)
File format................................ *.avi, *.mov, *.mp4,*.mkv,
................................................ *.flv, *.ts, *.m2ts, *.3gp
Photo formats ................................. JPEG, BMP, PNG, GIF
Music formats..................................................... MP3, WAV
Video Standard (CVBS)................... PAL, SECAM, NTSC
Video connection .........................................HDMI sockets
Internal speaker ............... stereo with subwoofer, 26 W
Internal memory............................................................4 GB
Compatible Memory Cards ......SD/SDHC/SDXC/MMC
USB connection max. power...........................5V, 500mA
Following accessories are available for your device:
PVideo-(CVBS) cable.....................PPA1320 / 253526178
3D Glasses.......................................PPA5610 / 253569764
For HDP1650 an HDP1650TV models:
RF remote control.........................PPA5650 / 253588194
All data are provided for reference purposes only.
Sagemcom Documents SAS reserves the right to
make any changes without prior notice.
Technology / optical
Display technology ...............................WXGA 0.45" DLP
Light source ........................................................... RGB LED
Native resolution......................... 1280 x 800 Pixel (16:9)
Supported Resolutions..................... VGA/SVGA/WVGA
..............................................XGA/WXGA/FULL HD
Projected image size (inch)...........................50 up to 100
Screen distance (mm).................................. 108 up to 441
Display refresh rate ............................. 60Hz/50Hz/120Hz
Power supply
Input .......................................100V-240V, 4.0 A, 50/60HZ
Power consumption....................................................150W
Off mode power consumption .............................. <0,5W
Manufacturer .................................... JQH Group Co., Ltd.
Appendix
41
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 42 Jeudi, 12. février 2015 11:31 11
The CE marking certifies that the product meets the
main requirements of the European Parliament and
Council directives 1999/5/CE, 2006/95/CE, 2004/108/
CE and 2009/125/CE on information technology equipment, regarding safety and health of users and regarding
electromagnetic interference.
The declaration of compliance can be consulted on the
site www.screeneo.philips.com.
Preservation of the environment as part of a sustainable
development plan is an essential concern of Sagemcom
Documents SAS. The desire of Sagemcom Documents
SAS is to operate systems observing the environment.
The desire of Sagemcom Documents SAS is to operate
systems observing the environment and consequently it
has decided to integrate environmental performances in
the life cycle of this products, from manufacturing to
commissioning use and elimination.
Federal Communications Commission (FCC)
Statement: You are cautioned that changes or
modifications not expressly approved by the party
responsible for compliance could void the user's
authority to operate the equipment.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will
not occur in a particular installation.If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference;
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
42
FCC RF Radiation Exposure Statement: This
transmitter must not be co-location or operating in
conjunction with any other antenna or transmitter. This
equipment complies with FCC RF radiation exposure
limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a
minimum distance of 7.8 inches (20 centimeters)
between the radiator and your body.
Canada Regulatory Compliance: This device
complies with Industry Canada CAN ICES-3 (B)/NMB3(B)
RSS-Gen & RSS-210 statement: This device
complies with Industry Canada licence-exempt RSS
standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation of the
device.
RF Radiation Exposure statement: The device
meets the exemption from the routine evaluation limits
in section 2.5 of RSS102 and users can obtain Canadian
information on RF exposure and compliance.
This equipment should be installed and operated with a
minimum distance of 7.8 inches (20 centimeters)
between the radiator and your body.
Packaging: The presence of the logo (green dot)
means that a contribution is paid to an approved
national organisation to improve package recovery and
recycling infrastructures. Please respect the sorting
rules set up locally for this kind of waste.
Batteries: If your product contains batteries, they
must be disposed of at an appropriate collection point.
Product: The crossed-out waste bin stuck on the
product means that the product belongs to the family of
electrical and electronic equipment. In this respect, the
European regulations ask you to dispose of it selectively;
• At sales points in the event of the purchase of
similar equipment.
• At the collection points made available to you
locally(drop-off centre, selective collection, etc.).
In this way you can participate in the re-use and upgrading of Electrical and Electronic Equipment Waste, which
can have an effect on the environment and human
health.
The paper and cardboard packaging used can be disposed of as recyclable paper. Have the plastic wrapping
recycled or dispose of it in the non-recyclable waste,
depending on the requirements in your country.
Philips · HDP16x0 & HDP16x0TV
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 43 Jeudi, 12. février 2015 11:31 11
Trademarks: The mentioned references in this manual are trademarks of the respective companies. The
lack of the trademarks É and Ë does not justify the
assumption that these dedicated terminologies are free
trademarks. Other product names used herein are for
identification purposes only and may be trademarks of
their respective owners. Sagemcom Documents SAS
disclaims any and all rights in those marks.
Neither Sagemcom Documents SAS nor its affiliates
shall be liable to the purchaser of this product or third
parties for damages, losses, costs, or expenses incurred
by the purchaser or third parties as a result of accident,
misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or failure to strictly comply with Sagemcom Documents SAS
operating and maintenance instructions.
Sagemcom Documents SAS shall not be liable for any
damages or problems arising from the use of any
options or any consumable materials other than those
designated as original Sagemcom Documents SAS /
PHILIPS products or Sagemcom Documents SAS /
PHILIPS approved products.
Sagemcom Documents SAS shall not be held liable for
any damage resulting from electromagnetic interference
that occurs from the use of any interface cables other
than those designated as Sagemcom Documents SAS /
PHILIPS products.
All rights reserved. No part of this publication may be
reproduced, stored in a retrieval system or transmitted
in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the
prior written permission of Sagemcom Documents SAS.
The information contained herein is designed only for
use with this product. Sagemcom Documents SAS is not
responsible for any use of this information as applied to
other devices.
This user manual is a document that does not represent
a contract.
Errors, printing errors and changes are reserved.
Copyright È 2015 Sagemcom Documents SAS
Appendix
Imported for USA / Importé pour les États-Unis /
Importado para Estados Unidos
P&F USA, Inc.
PO Box 2248
Alpharetta, Ga 30023-2248
For further assistance, call the customer support
service in your country: 1 866 310 0788
Imported for Canada / Importé pour le Canada /
Importado para Canadas
Bigtech
5990 14th Avenue
Markham, Ontario L3S 4M4
Pour obtenir de l’aide supplémentaire, communiquez
avec le centre de service à la clientèle de votre
pays : 1 866 310 0788
Exclusivo para México. For Mexico only. Exclusivement
pour le Mexique
PROYECTOR (Screeneo)
Alimentación: 100 – 240V ~ 50/60Hz 4A
Consumo de Energía Eléctrica 150 Wh
Consumo de Energía Eléctrica del aparato en Modo de
Espera < 0,5 Wh
Importador:
P&F Mexicana. S.A. de C.V.
Av. La Palma No 6. Col. San Fernando La Herradura
Huixquilucan. Edo. de México. MEXICO C.P. 52787
Tel 52 (55) 52699000
EXPORTADOR: P&F USA INC.
HECHO EN CHINA
GARANTIA INCLUIDA EN EL INSTRUCTIVO DE
USO
MODEL N° (i.e. HDP1690/F7)
43
Screeneo_User-Manual_HDP16x0_V1-1_EN-US_253634032-A.book Page 43 Jeudi, 12. février 2015 11:31 11
PHILIPS and the PHILIPS’ Shield Emblem are registered trademarks of Koninklijke Philips N.V.
and are used by Sagemcom Documents SAS under license from Koninklijke Philips N.V.
È 2015 Sagemcom Documents SAS
All rights reserved
Sagemcom Documents SAS
Documents Business Unit
Headquarters : 250, route de l’Empereur
92848 Rueil-Malmaison Cedex · FRANCE
Tel: +33 (0)1 57 61 10 00 · Fax: +33 (0)1 57 61 10 01
www.sagemcom.com
Simplified Joint Stock Company · Capital 8.479.978 € · 509 448 841 RCS Nanterre
HDP16x0TV
EN-US
253637294-A