- Computers & electronics
- Audio & home theatre
- Supplementary music equipment
- MarkBass
- CMD 103H
- Owner's manual
advertisement
▼
Scroll to page 2
of 8
v. 26.march.2013 owner’s manual LITTLE MARK III ~ LITTLE MARK 250 ~ LITTLE MARK 800 ~ COMBO HEAD II / LITTLE MARK TUBE ~ LITTLE MARK TUBE 800 1. IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions; 2) Keep these instructions; 3) Heed all warnings; 4) Follow all instructions; 5) Do not use this apparatus near water; 6) Clean only with dry cloth; 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions; 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat; 9) Do not defeat the safety purpose of the polarized or ground-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet; 10) Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus; 11) Only use attachments/accessories specified by the manufacturer; 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from the tip-over (and Fig 21 DU Tipping Cart Symbol). 13) Unplug this apparatus during lightning storms or when unused for long periods of time; 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped; 15) “Warning: to reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture; and objects filled with liquids, such as vases, should not be placed on this apparatus”; 16) The socket outlet shall be installed near the equipment and shall be easily accessible; 17) The power cord must be unplugged prior to servicing. 1. PRÉCAUTIONS D’EMPLOI 1) Lire ces instructions; 2) Conserver ces instructions; 3) Suivre tous les conseils d’utilisations; 4) Suivre toutes les instructions; 5) Ne pas utiliser cet appareil au bord de l’eau; 6) Nettoyer uniquement avec un chiffon humide; 7) Ne pas bloquer le système de ventilation. Installer conformément aux instructions du fabricant; 8) Ne pas installer l’appareil près d’une source de chaleur tel qu’un radiateur, un fourneau, ou bien un autre appareil qui produit de la chaleur; 9) Ne pas modifier le système de sécurité de la fiche polarisée ou de de la fiche pour les prises de terre. Une fiche polarisée a deux broches, l’une étant plus distante de l’autre. Une fiche pour prise de terre a deux broches et une pointe pour la masse. La broche plus distante et la pointe pour la masse ont été installées pour votre sécurité. Si la fiche fournie de rentre pas dans votre prise de courant consulter un électricien pour la substitution; 10) Protéger le cordon d’alimentation afin qu’il ne soit pas piétiné ou écrasé tout particulièrement au niveau des fiches, des prises de courant femelles, et des parties qui sortent de l’appareil; 11) Utiliser uniquement les accessoires recommendés par le fabricant; 12) Utilisez uniquement avec le chariot, le socle, le trépied, le support ou la table spécifiés par le fabricant ou vendu avec l’appareil. Lorsque vous utilisez un chariot, soyez prudent lorsque vous déplacez l’ensemble chariot / appareil pour éviter toute blessure du renversement (et la figure 21 DU Tipping panier Symbol). 13)Ne pas branché l’appareil en cas d’orage accompagné d’éclairs. Le débrancher en cas de non utilisation prolongée; 14) S’adresser à un service assistance agréé si l’appareil a subi des dommages, si le cordon d’alimentation ou la fiche a été endommagé, si un liquide a été renversé sur l’appareil ou bien si un object est tombé dans l’appareil, si ce dernier a été exposé à la pluie ou à l’humidité, s’il ne fonctionne pas correctement ou s’il est tombé; 15) “Avertissant: pour réduire le risque du feu ou de décharge électrique, n’exposez pas cet appareil à la pluie ou l’humidité et les objets remplis de liquides; tels que des vases, ne devraient pas être placés sur cet appareil”; 16) La prise de courant doit être installée près de l’appareil et doit être facilement accessible; 17) La fiche principale doit être débranchée avant toute opération d’entretien. MORE INFORMATION For warrantee and service information, please contact your local Markbass distributor (contact information available at www.markbass.it). For more technical information, please visit us at www.markbass.it and fill out the form on the Contact Us page. We hope you enjoy your amp and use it to make great music! “The Lightning Flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product enclosure that may be of sufficient magnitude to constitute a risk of shock to persons.” 02 “The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.” 2. LITTLE MARK III / LITTLE MARK 250 / LITTLE MARK 800 / COMBO HEAD II FRONT PaneL 3. LITTLE MARK TUBE / LITTLE MARK TUBE 800 FRONT PaneL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 UNBALANCED 1/4” JACK INPUT BALANCED XLR INPUT SOLID STATE GAIN CLIP LED LOW EQUALIZATION CONTROL KNOB MID LOW EQUALIZATION CONTROL KNOB MID HIGH EQUALIZATION CONTROL KNOB HIGH EQUALIZATION CONTROL KNOB VLE FILTER LEVEL CONTROL KNOB VPF FILTER LEVEL CONTROL KNOB MASTER VOLUME LEVEL KNOB LINE OUT LEVEL KNOB POWER ON LED MAIN ON/OFF SWITCH UNBALANCED 1/4” JACK INPUT BALANCED COMBO XLR / 1/4” JACK INPUT 1/4” JACK INPUT GAIN COMBO XLR / 1/4” JACK GAIN CLIP LED PHANTOM POWER 48V ON/OFF SWITCH (ON BALANCED COMBO XLR / 1/4” JACK INPUT) LINE OUT LEVEL KNOB MIX LEVEL CONTROL KNOB LOW EQUALIZATION CONTROL KNOB MID LOW EQUALIZATION CONTROL KNOB MID HIGH EQUALIZATION CONTROL KNOB HIGH EQUALIZATION CONTROL KNOB VLE FILTER LEVEL CONTROL KNOB MASTER VOLUME LEVEL KNOB (PULL OUT TO MUTE) VPF FILTER LEVEL CONTROL KNOB POWER ON LED MAIN ON/OFF SWITCH 4. LITTLE MARK III / LITTLE MARK 250 / LITTLE MARK 800 / COMBO HEAD II / LITTLE MARK TUBE / LITTLE MARK TUBE 800 REAR PaneL 1 2 3 4 5 6 7 8 9 AC POWER SOCKET SPEAKER OUT SPEAKON / 1/4” COMBO JACK SPEAKER OUT 1/4” JACK TUNER OUT 1/4” JACK RETURN EFFECT 1/4” JACK SEND EFFECT 1/4” JACK PRE/POST EQUALIZATION CONTROL SWITCH GROUND LIFT CONTROL SWITCH LINE OUT XLR 2 1 3 4 5 6 7 8 9 03 5. LITTLE MARK III / LITTLE MARK 250 / LITTLE MARK 800 / COMBO HEAD II Technical Details INPUTS INPUT BALANCED RETURN EFFECT CONTROLS GAIN LINE OUT PRE/POST EQ (for line out) GROUND LIFT MASTER VOLUME impedance: 500 Kohm, max. voltage: 15 Vpp impedance: 100 Kohm, max. voltage: 25 Vpp impedance: 33 Kohm, max. voltage: 10 Vpp –60 dB to +23 dB range level control on front panel switch on rear panel switch on rear panel EQUALIZATION LOW MID LOW MID HIGH HIGH VLE (Vintage Loudspeaker Emulator) VPF (Variable Pre-shape Filter) center frequency 40 Hz; level: ±16 dB center frequency 360 Hz; level: ±16 dB center frequency 800 Hz; level: ±16 dB center frequency 10 kHz; level: ±16 dB max cut range: 250 Hz – 20 kHz center frequency 380 Hz (cut) OUTPUTS SEND EFFECTS TUNER OUT LINE OUT SPEAKER OUT unbalanced, max. voltage 20 Vpp unbalanced, max. voltage 2 Vpp balanced XLR, max. voltage 20 Vpp speakon/1/4” combo, 1/4” OTHER HEIGHT WIDTH DEPTH WEIGHT 2 rack units (3.16 in. / 80.3 mm) 10.87 in. / 27.6 cm (19 in. / 48.3 cm with rack ears) 10.04 in. / 25.5 cm 6.39 lbs / 2.9 kg (LITTLE MARK III) 6.15 lbs / 2.79 kg (LITTLE MARK 800) 5.73 lbs / 2.6 kg (LITTLE MARK 250) OUTPUT POWER 300W RMS @ 8 ohm, 500W RMS @ 4 ohm (LITTLE MARK III, COMBO HEAD II) 450W RMS @ 8 ohm, 750W RMS @ 4 ohm (LITTLE MARK 800) 150W RMS @ 8 ohm, 250W RMS @ 4 ohm (LITTLE MARK 250) POWER REQUIREMENT 100V; 120V; 230V; 240V 50/60Hz (Voltage is factory preset according to region of sale). Markbass amps/combos are manufactured to be sold and used in the country of purchase, and are factory preset to that country’s voltage. Due to homologation issues, the voltage may not be changed. FUSE LITTLE MARK III, COMBO HEAD II: EUROPE AUSTRALIA/UK USA/CANADA JAPAN 4 A 250V T 5x20 4 A 250V T 5x20 8 A 250V T 5x20 10 A 250VT 5x20 LITTLE MARK 800: EUROPE AUSTRALIA/UK USA/CANADA JAPAN 6.3 A 250V T 5x20 6.3 A 250V T 5x20 8 A 250V T 5x20 10 A 250VT 5x20 LITTLE MARK 250: EUROPE AUSTRALIA/UK USA/CANADA JAPAN 04 3.15 A 250V T 5x20 3.15 A 250V T 5x20 6.3 A 250V T 5x20 6.3 A 250VT 5x20 6. COMBOS: TECHNICAL DETAILS COMBO SERIES CMD 102P CMD 103H MINI CMD 121P CMD 121H MINI CMD 151P CMD 151P CMD JB JEFF BERLINPLAYER SCHOOL Speaker Size (inches) 2x10” 3x10” 1x12” 1x12” 1x15” 1x15” 1x15” TweeterPiezo Tweeter 1” HF Comp. Driver Piezo Tweeter 1” HF Comp. Driver Piezo Tweeter None None Crossover Frequency 3.5 kHz 3.5 kHz 3.5 kHz 3.5 kHz 3.5 kHz NoneNone CAB Power Handling (AES Standard) 400W RMS 600W RMS 400W RMS 400W RMS 400W RMS 400W RMS 250W RMS Frequency Response 40Hz to 18kHz 40Hz to 20kHz 45Hz to 18kHz 45Hz to 20kHz 40Hz to 18kHz 40Hz to 5kHz 45HZ TO 5KHZ Cabinet Sensitivity (dB SPL) 1011039999100100 99 Cabinet Impedance 8 Ω 6 Ω 8 Ω 8 Ω 8 Ω 8 Ω 8Ω ReflexFRONTRearRearRearRearRearRear Weight kg. Weight lbs. 2028.713.317.918.521.218.5 44.09 63.27 29.32 39.46 40.79 46.74 40.79 Width mm. Widht inches 594 594 390 390 464 464 464 23.3923.33915.3515.3518.2718.2718.27 Height mm. Height inches 479 18.86 699 27.52 432 17.01 599 23.58 464 18.27 557 21.93 464 18.27 Depth mm. Depth inches 475 18.70 480 18.90 357 14.06 464 18.27 480 18.90 480 19.90 480 18.90 PreampSolid-stateSolid-stateSolid-stateSolid-stateSolid-stateSolid-stateSolid-state Power Amp 300W @ 8 Ω / 500W @ 4 Ω Power Supply All models are equipped with custom-designed Markbass digital power supplies 300W @ 8 Ω / 500W @ 4 Ω 300W @ 8 Ω / 500W @ 4 Ω 300W @ 8 Ω / 500W @ 4 Ω 300W @ 8 Ω / 500W @ 4 Ω 300W @ 8 Ω / 500W @ 4 Ω 150W @ 8 Ω / 250W @ 4 Ω 05 7. LITTLE MARK TUBE / LITTLE MARK TUBE 800 Technical Details INPUTS INPUT 1 INPUT 2 RETURN EFFECT CONTROLS GAIN 1 GAIN 2 LINE OUT PRE/POST EQ (for line out) GROUND LIFT MUTE MASTER VOLUME impedance: 500 Kohm, max. voltage: 15 Vpp balanced XLR, impedance: 500 Kohm, max. voltage: 15 Vpp impedance: 33 Kohm, max. voltage: 10 Vpp –60 dB to +23 dB range –60 dB to +23 dB range level control on front panel switch on rear panel switch on rear panel pulling out the Master knob EQUALIZATION LOW MID LOW MID HIGH HIGH VLE (Vintage Loudspeaker Emulator) VPF (Variable Pre-shape Filter) center frequency: 40 Hz; level: ±16 dB center frequency: 360 Hz; level: ±16 dB center frequency: 800 Hz; level: ±16 dB center frequency: 10 kHz; level: ±16 dB max. range cut: 250 Hz – 20 kHz center frequency 380 Hz (cut) OUTPUTS SEND EFFECT TUNER OUT LINE OUT SPEAKER OUT unbalanced, max. voltage 20 Vpp (pre-EQ) unbalanced, max. voltage 2 Vpp balanced XLR, max. voltage 20 Vpp speakon/1/4” combo, 1/4” OTHER HEIGHT2 rack units (3.16 in. / 80.3 mm) WIDTH10.87 in. / 27.6 cm (19 in. / 48.3 cm with rack ears) DEPTH10.04 in. / 25.5 cm WEIGHT 6.55 lbs / 2.97 kg (LITTLE MARK TUBE) 6.31 lbs / 2.86 kg (LITTLE MARK TUBE 800) 06 OUTPUT POWER 300W RMS @ 8 ohm, 500W RMS @ 4 ohm (LITTLE MARK TUBE) 450W RMS @ 8 ohm, 750W RMS @ 4 ohm (LITTLE MARK TUBE 800) POWER REQUIREMENT 100V; 120V; 230V; 240V 50/60Hz (Voltage is factory preset according to region of sale). Markbass amps/combos are manufactured to be sold and used in the country of purchase, and are factory preset to that country’s voltage. Due to homologation issues, the voltage may not be changed. FUSE LITTLE MARK TUBE: EUROPE AUSTRALIA/UK USA/CANADA JAPAN 4 A 250V T 5x20 4 A 250V T 5x20 8 A 250V T 5x20 10 A 250VT 5x20 LITTLE MARK TUBE 800: EUROPE AUSTRALIA/UK USA/CANADA JAPAN 6.3 A 250V T 5x20 6.3 A 250V T 5x20 8 A 250V T 5x20 10 A 250VT 5x20 8. TROUBLESHOOTING TIPS THERMAL PROTECTION SYMPTOM The amp gets hot and shuts down. PROBABLE CAUSE The amp has overheated, either as a result of inadequate ventilation or a damaged cooling system fan. When the amplifier cools down to a safe level, the amp will automatically restart. SUGGESTIONS Please verify that the fan is working properly, and that the cooling system ports are not obstructed. CURRENT PROTECTION SYMPTOM The amp turns on, but there is no signal coming from the speaker/s. PROBABLE CAUSE Low impedance load (minimum impedance for Markbass amps is 4 ohms), or a bad speaker cable. SUGGESTIONS Please verify the impedance of the speaker/s connected to the amp. Note that two 4 ohm cabinets, or an 8 ohm and a 4 ohm cabinet, will result in an impedance below 4 ohms. Please check the speaker cable/s. After checking these two things, please turn the amp off and turn it on again. If the troubleshooting steps outlined above do not solve your problem, please contact your Markbass distributor/dealer for service information. For more TROUBLESHOOTING TIPS, please check the FAQ section on the SUPPORT page of our website at www.markbass.it. 07 Product specifications are subject to change without notice Italy - 66020 San Giovanni Teatino (Ch) - Via Po, 52 - Tel. +39 085 446 3755 - Fax +39 085 440 7764 www.markbass.it - [email protected]
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project