NIGHT VisionAire

®

Instruction Manual

Bedienungsanleitung

Manuel d’utilisation

Manuale di Istruzioni

EN

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product.

Meaning of Special Language:

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superfi cial injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by

Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

14+ AGE RECOMMENDATION:

Not for children under 14 years. This is not a toy.

WARNING AGAINST COUNTERFEIT PRODUCTS: If you ever need to replace your Spektrum receiver found in a Horizon Hobby product, always purchase from Horizon Hobby, LLC or a Horizon Hobby authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with

DSM or Spektrum.

Safety Precautions and Warnings

As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or the property of others.

• Always keep a safe distance in all directions around your model to avoid collisions or injury. This model is controlled by a radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control.

• Always operate your model in open spaces away from full-size vehicles, traffi c and people.

• Always carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.).

• Always keep all chemicals, small parts and anything electrical out of the reach of children.

• Always avoid water exposure to all equipment not specifi cally designed and protected for this purpose. Moisture causes damage to electronics.

• Never place any portion of the model in your mouth as it could cause serious injury or even death.

• Never operate your model with low transmitter batteries.

• Always keep aircraft in sight and under control.

• Always use fully charged batteries.

• Always keep transmitter powered on while aircraft is powered.

• Always remove batteries before disassembly.

• Always keep moving parts clean.

• Always keep parts dry.

• Always let parts cool after use before touching.

• Always remove batteries after use.

• Always ensure failsafe is properly set before fl ying.

• Never operate aircraft with damaged wiring.

• Never touch moving parts.

2

To register your product online, visit www.e-fl iterc.com

Box Contents

Quick Start Information

Transmitter

Setup

Set up your transmitter using the transmitter setup chart.

Dual Rates

High

100%

Low

70%

Flight Timer

Setting

First fl ight 4 Min.

6 Min.

Specifi cations

Motor: BL10 Brushless outrunner

1250Kv

ESC: 40-Amp Lite Pro Switch

Mode BEC Brushless ESC (V2)

(EFLA1040LB)

(4) Servos (EFLR7155)

Receiver: Spektrum ™ AR636

6-Channel Sport Receiver

Battery: 2200mA 11.1V 3S 25C

Li-Po (EFLB22003S30)

Battery Charger: 3-cell Li-Po battery balancing charger

Recommended Transmitter:

Full-Range 2.4GHz with

Spektrum ™ DSM2 ® /DSMX ® technology. (DX4e and above)

45 in (1143mm)

Included

Installed

Installed

Installed

Required to

Complete

Required to

Complete

Required to

Complete

51.0 oz

(1450 g)

539 sq in

(34.8 sq dm)

SAFE ® Technology Flight Modes .........................................................4

Transmitter Setup for this SAFE ® Technology Aircraft .........................5

Model Assembly ................................................................................6

Model Assembly Continued ................................................................7

Trimming ...........................................................................................8

Control Horn and Servo Arm Settings .................................................8

Transmitter and Receiver Binding .......................................................9

Battery Installation and ESC Arming .................................................10

Center of Gravity (CG) .....................................................................11

Control Direction Tests .....................................................................11

AS3X Control Direction Test ............................................................12

Flying Tips and Repairs ....................................................................13

Guidlines for Flying 3D .....................................................................14

Post Flight .......................................................................................14

Power Component Service ...............................................................15

Troubleshooting Guide SAFE ............................................................15

Troubleshooting Guide .....................................................................16

AMA National Model Aircraft Safety Code .........................................17

Limited Warranty .............................................................................18

Contact Information .........................................................................19

FCC Information ...............................................................................19

IC Information ..................................................................................19

Compliance Information for the European Union ...............................19

Replacement Parts ...........................................................................70

Optional Parts ..................................................................................71

Prefl ight

1 Remove and inspect contents.

2 Read this instruction manual thoroughly.

3 Charge fl ight battery.

4 Setup Transmitter using transmitter setup chart.

5 Fully assemble airplane.

6 Install the fl ight battery in the aircraft (once it has been fully charged).

7 Check the Center of Gravity (CG).

8 Bind aircraft to your transmitter.

9 Make sure linkages move freely.

10 Perform the Control Direction Test with the transmitter.

11 Perform the AS3X Control Direction Test with the aircraft.

12 Adjust fl ight controls and transmitter.

13 Perform a radio system Range Test.

14 Find a safe open area to fl y.

15 Plan fl ight for fl ying fi eld conditions.

3

EN

EN

SAFE

®

Technology Flight Modes

This aircraft has 2 selectable fl ight modes and a Panic Recovery feature. It is extremely important to follow the Transmitter Setup section of this manual before binding your transmitter to this aircraft .

Precision Mode:

This mode uses low rates and low gains to deliver precise response at high airspeeds. Use this mode to trim the aircraft and fl y fast precision maneuvers.

3D Mode:

This mode uses high rates and high gains to deliver extreme maneuverability with maximum stability at low airspeeds. Use this mode for slow fl ying and 3D maneuvers such as Hovers and Harriers. Flying at high speed in this mode could cause oscillation.

2 Position Gear/Ch 5 Switch Transmitters

DX6i and DX5e,

DX4e (older versions)

Precision Mode (Low Rate)

Position 0 is Precision Mode

3D Mode (High Rate)

Position 1 is 3D Mode

Important: DX6i ch5 has to be reversed.

3 Position Gear/Ch 5 Switch Transmitters

DX4e, DX5e, DX6,

DX7S, DX8, DX9,

DX18, DX10t

Precision Mode (Low Rate)

Positions 0 and 1 are

Precision Mode

3D Mode (High Rate)

Position 2 is 3D Mode

Panic Recovery Mode

If you feel you have lost control of the aircraft (in any mode), hold the Panic

Recovery button/switch. The SAFE technology will return the aircraft to upright fl ight.

Always fl y at a safe altitude, as Panic Recovery may cause the aircraft to lose altitude while returning to upright fl ight. Release the Panic Recovery button/ switch to turn off Panic mode and return to the current SAFE fl ight mode with full stick control again.

IMPORTANT: If the aircraft is upside down when the Panic Recovery button/ switch is pressed, suffi cient altitude may be required for the aircraft to return to upright fl ight.

CH 5

DX4e shown. Panic Button /

Switch may vary depending on Transmitter model. See

Transmitter setup for more info.

4

Transmitter Setup for this SAFE

®

Technology Aircraft

It is extremely important to folow these transmitter setup charts to assign your transmitter switches correctly to operate the fl ight modes and Panic Recovery correctly.

The installed AR636 receiver has been programmed for operation specifi cally in this aircraft. The fl ight modes can be changed in fl ight using a toggle switch

(Gear/Channel 5 Switch).

Use the provided charts to guide you through transmitter setup. Locate your specifi c transmitter in the chart and follow the numbered setup sequence. The ending results will be:

Non-Computerized Transmitter Setup

(DX4e and DX5e)

Before binding a non-computerized transmitter, ensure all servo reversing is set to normal and trim is at center.

DX6i

Flight Modes

Panic Switch

DX7S/DX8

Panic Switch

Flight Modes

DX6, DX9, DX18

Flight Modes

Panic Switch

DX10t

Flight Modes

Trainer/Bind button (DX7S, DX8)

Bind button (DX6, DX9, DX18)

Panic Switch

Computerized Transmitter Setup

(DX6i) • (DX7S, DX8) • (DX6, DX9 and DX18) • (DXt10)

Start all transmitter programming with a blank ACRO model (do a model reset), then name the model.

Set Dual Rates to: HIGH 100% LOW 70%

Set Servo Travel to: 100%

DX6i

1. Go to the SETUP LIST MENU

2. Set MODEL TYPE: ACRO

3. Set REVERSE: Gear Channel

4. Go to ADJUST LIST MENU

5. Set FLAPS: Norm …100, LAND †100

Resulting in:

The Gear switch operates the 2 SAFE modes.

Gear 0: = Precision Mode

Gear 1: = 3D Mode

The Flap switch operates Panic Recovery:

0=Off

Position 1=On. (not a momentary switch)

DX7S and DX8

1. Go to the SYSTEM SETUP

2. Set MODEL TYPE: AIRPLANE

3. Set SWITCH SELECT: Change all to INH:

Then TRAINER: AUX1

Then GEAR

4. Go to the FUNCTION LIST

5. Set SERVO SETUP: Reverse AUX1

Resulting in:

F-Mode Switch operates the 2 SAFE modes.

0 and 1 = Precision Mode

2 = 3D Mode

The Trainer/Bind button operates Panic Recovery

DX6, DX9, DX18 and DX10t

1. Go to the SYSTEM SETUP

2. Set MODEL TYPE: AIRPLANE

3. Set WING TYPE: NORMAL

4. Go to CHANNEL ASSIGN:

NEXT:

Channel Input Confi g:

Set GEAR: B (DX10t: GEAR: A)

Set AUX1: I (DX10t: AUX1: R-TIP)

5. Go to the FUNCTION LIST

6. Set SERVO SETUP: Reverse AUX1

Resulting in:

Switch B (DX10t: A) operates the 2 SAFE modes.

0 and 1 = Precision Mode

2 = 3D Mode

The Bind/I button (DX10t: R-TIP) operates Panic

Recovery

IMPORTANT: After you set up your model, always rebind the transmitter and receiver to set the desired failsafe positions.

EN

5

EN

Model Assembly

Landing Gear Installation

1. Install the landing gear strut (A) with the wheels raked forward as shown.

2. Install the cover (B) on the fuselage using 4 screws (C).

Disassemble in reverse order.

A

B

C

Horizontal Tail Installation

1. Slide the horizontal tail tube (A) into the hole in the rear of the fuselage.

2. Install the 2 piece (left and right) horizontal tail as shown. Ensure the control horn faces down.

3. Connect the LED connectors to either side of the LED light harness in the fuselage.

4. Apply 8 pieces of tape (B) to the fuselage mounts (two on the top and bottom of each half of the horizontal tail).

5. Attach the clevis to the elevator control horn (see instructions for clevis connection).

6. When needed, disassemble in reverse order.

A

B

6

Model Assembly Continued

SFG Installation

1. Carefully apply the included tape (A) to the wing fence base.

2. Align and install the left and right (marked L and R) top and bottom wing fences (B) into the respective wing slots (C). The bottom fences have integrated plastic skids, as shown.

If desired, apply a small amount of thin CA (cyanoacrylate adhesive) to the fences and wings.

C

A

B

Wing Installation

1. Slide the wing tube (A) into the fuselage.

CAUTION: DO NOT crush or otherwise damage the wiring when attaching the wing to the fuselage.

2. Install the left and right wing (B and C) over the wing tube and into the wing slot of the fuselage while inserting the aileron servo and LED connectors through the provided holes.

3. Invert the fuselage so the landing gear is facing up. Secure the left and right wings to the fuselage using the included screws (D).

4. Remove the screw (E) and the receiver cover (F) from the bottom of the fuselage.

Tip: If needed, use hemostats or pliers to pull the servo and LED connectors into the fuselage.

5. Connect the aileron servos from the wings to the Y-harness connectors in the fuselage. The left and right aileron servos can be connected to either side of the Y-harness.

6. Connect the LED connectors to either side of the LED light harness in the fuselage.

7. Replace the receiver cover and the screw.

Disassemble in reverse order.

IMPORTANT: Correct operation of the AS3X ® system requires connection of both ailerons to the included Y-harness and the AILE channel of the receiver.

D

B

A

C

EN

7

EN

Clevis Installation

• Pull the tube from the clevis to the linkage.

• Carefully spread the clevis, then insert the clevis pin into the desired hole in the control horn.

• Move the tube to hold the clevis on the control horn.

1.

2.

3.

Control Surface Centering

After assembly and transmitter setup, confi rm that the control surfaces are centered. If the control surfaces are not centered, mechanically center the control surfaces by adjusting the linkages.

If adjustment is required, turn the clevis on the linkage to change the length of the linkage between the servo arm and the control horn.

After binding a transmitter to the aircraft receiver, set the trims and sub-trims to 0, then adjust the clevises to center the control surfaces.

4.

5.

6.

Trimming

IMPORTANT: Only trim this aircraft in Precision Flight Mode.

After adjusting transmitter trim in the air or on the ground, do not touch the

control sticks for 2 seconds. This allows the receiver to learn the correct settings to optimize AS3X performance.

Failure to do so could affect fl ight performance.

2 Seconds

8

Control Horn and Servo Arm Settings

The table to the right shows the factory settings for the control horns and servo arms. Fly the aircraft at factory settings before making changes.

NOTICE: If control throws are changed from the factory settings, the AR636 gain values may need to be adjusted. Refer to the Spektrum AR636 manual for adjustment of gain values.

IMPORTANT: Adjusting the programming of the AR636 receiver is not recommended. If the programming is adjusted the receivers SAFE function could be compromised. Refer to the AR636 receiver instruction manual online.

After fl ying, you may choose to adjust the linkage positions for the desired control response.

Elevator

Rudder

Horns

Ailerons

Arms

Transmitter and Receiver Binding

Binding is the process of programming the receiver to recognize the GUID

(Globally Unique Identifi er) code of a single specifi c transmitter. You need to

‘bind’ your chosen Spektrum ™ DSM2 ® /DSMX ® technology equipped aircraft transmitter to the receiver for proper operation.

IMPORTANT: Before binding a transmitter, read the Transmitter Setup section of this manual to ensure that your transmitter is properly programmed for this aircraft.

Binding Procedure

IMPORTANT: The included AR636 receiver has been programmed for operation specifi cally for this aircraft. Refer to the receiver manual for correct setup if the receiver is replaced or is used in another aircraft.

Read the transmitter instructions for binding to a receiver (location of transmitter’s Bind control). Please visit www.bindnfl y.com for a com- plete list of compatible transmitters.

CAUTION: When using a Futaba ® transmitter with a Spektrum DSM module, you must reverse the throttle channel and rebind. Refer to your

Spektrum module manual for binding and failsafe instructions. Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.

1. Make sure the transmitter is powered off.

2. Move the transmitter controls to neutral (fl ight controls: rudder, elevators and ailerons) or to low positions (throttle, throttle trim).**

3. Install a bind plug in the receiver bind port extension.

4. Connect the fl ight battery to the ESC. The ESC will produce a series of sounds. One long tone, then 3 short tones confi rm that the LVC is set correctly for the ESC. The orange bind LED on the receiver will begin to fl ash rapidly.

5. Power on the transmitter while holding the transmitter bind button or switch. Refer to your transmitter’s manual for binding.

6. When the receiver binds to the transmitter, the orange bind light on the receiver will turn solid and the ESC will produce a series of three ascending tones. The tones indicate the ESC is armed, provided the throttle stick and throttle trim are low enough to trigger arming.

7. Remove the bind plug from the bind port extension.

8. Safely store the bind plug (some owners attach the bind plug to their transmitter using two-part loops and clips).

9. The receiver should retain the binding instructions received from the transmitter until another binding is done.

* The throttle will not arm if the transmitter’s throttle control is not put at the lowest position. If you encounter problems, follow the binding instructions and refer to the transmitter troubleshooting guide for other instructions. If needed, contact the appropriate Horizon Product Support offi ce.

**Failsafe

If the receiver loses transmitter communication, the failsafe will activate.

When activated, the airplane controls return to the neutral position established during step 2 of the binding procedure.

Bind Plug Installation

BIND PLUG

EN

9

EN

Battery Installation and ESC Arming

Battery Selection

We recommend the E-fl ite ® 2200mAh 11.1V 3S 30C Li-Po battery

(EFLB22003S30). Refer to the Optional Parts List for other recommended batteries. If using a battery other than those listed, the battery should be within the range of capacity, dimensions and weight of the E-fl ite Li-Po battery packs to fi t in the fuselage. Be sure the model balances at the recommended CG.

1. Lower the throttle and throttle trim to the lowest settings. Power on the

Transmitter, then wait 5 seconds.

2. Apply hook and loop tape to the bottom of your battery.

3. Push the button (A) into the fuselage and remove the battery hatch.

4. Install the fully charged battery (B) in the battery compartment as shown.

See the Adjusting the Center of Gravity instructions for more information.

5. Make sure the fl ight battery is secured using the hook and loop strap (C).

6. Connect the battery to the ESC (the ESC is now armed).

7. Keep the aircraft immobile and away from wind or the system will not initialize.

• The ESC will sound a series of tones (refer to step 6 of the binding

instructions for more information).

• An LED will light on the receiver.

If the ESC sounds a continuous double beep after the fl ight battery is connected, recharge or replace the battery.

8. Reinstall the battery hatch. Push the rear of the battery hatch securely to ensure the latch is fully engaged.

B

A

C

CAUTION: Always keep hands away from the propeller. When armed, the motor will turn the propeller in response to any throttle movement.

10

Center of Gravity (CG)

The CG location is measured from the leading edge of the wing at the root.

This CG location has been determined with the recommended Li-Po battery installed near the center of the battery compartment.

Tip: You can fl y your aircraft inverted to confi rm CG is correct. The aircraft should fl y level when fl ying inverted at ¾ throttle with little or no elevator down pressure. If the aircraft CG is too far forward (nose-heavy), signifi cant down elevator is required to fl y level. If the aircraft CG is too far aft (tail-heavy), up elevator is required to fl y level.

Control Direction Tests

Assemble the aircraft and bind your transmitter to the receiver before performing this test.

After binding a transmitter to the aircraft receiver, set the trims and sub-trims to 0, then adjust the clevises to center the control surfaces.

Move the controls on the transmitter to make sure the aircraft control surfaces move in the proper direction.

125-130mm back from leading edge at the root.

Transmitter

Command

Up Elevator

Command

Down

Elevator

Command

Stick Right

Aircraft Reaction

Stick Left

Stick Right

Stick Left

EN

11

EN

AS3X Control Direction Test

This test ensures that the AS3X control system is functioning properly.

Assemble the aircraft and bind your transmitter to the receiver before performing this test.

1. Raise and then lower the throttle to activate AS3X.

2. Move the entire aircraft as shown and ensure the control surfaces move in the direction indicated in the graphic. If the control surfaces do not respond as shown, do not fl y the aircraft. Refer to the receiver manual for more information.

Once the AS3X system is active, control surfaces may move rapidly. This is normal. AS3X is active until the battery is disconnected.

Aircraft movement

AS3X Reaction

12

Flying Tips and Repairs

Consult local laws and ordinances before choosing a fl ying location.

Range Check your Radio System

Before you fl y, range check the radio system. Refer to your specifi c transmitter instruction manual for range test information.

Oscillation

Once the AS3X system is active (after advancing the throttle for the fi rst time), you will normally see the control surfaces react to aircraft movement. In some fl ight conditions you may see oscillation (the aircraft rocks back and forth on one axis due to overcontrol). If oscillation occurs, decrease airspeed. If oscillation persists, refer to the Troubleshooting Guide for more information.

NOTICE: Fast fl ight in 3D Mode will cause oscillation and may damage the aircraft.

Takeoff

Place the aircraft in position for takeoff (facing into the wind). Select low rates for fi rst takeoff and gradually increase the throttle to 3/4 to full and steer with the rudder. Pull back gently on the elevator and climb to a comfortable altitude.

Wind can also be landed in a three-point attitude, where all three wheels touch down at the same time. When the aircraft touches down, reduce back pressure on the elevator stick to prevent the plane from becoming airborne again.

If landing on grass, it is best to hold full up elevator after touchdown and when taxiing to prevent nosing over.

Once on the ground, avoid sharp turns until the plane has slowed enough to prevent scraping the wingtips.

NOTICE: If a crash is imminent, reduce the throttle and trim fully. Failure to do so could result in extra damage to the airframe, as well as damage to the ESC and motor.

WARNING:

Always decrease throttle at propeller strike.

NOTICE: After any impact, always ensure the receiver is secure in the fuselage. If you replace the receiver, install the new receiver in the same orientation as the original receiver or damage may result.

NOTICE: Crash damage is not covered under warranty.

NOTICE: When you are fi nished fl ying, never leave the aircraft in direct sunlight or in a hot, enclosed area such as a car. Doing so can damage the foam.

Fly in this area

600 feet (182.8 m)

Stand here

Low Voltage Cutoff (LVC)

When a Li-Po battery is discharged below 3V per cell, it will not hold a charge.

The ESC protects the fl ight battery from over-discharge using Low Voltage

Cutoff (LVC). Before the battery charge decreases too much, LVC removes power supplied to the motor. Power to the motor pulses, showing that some battery power is reserved for fl ight control and safe landing.

Disconnect and remove the Li-Po battery from the aircraft after use to prevent trickle discharge. Charge your Li-Po battery to about half capacity before storage. During storage, make sure the battery charge does not fall below 3V per cell. LVC does not prevent the battery from over-discharge during storage.

NOTICE: Repeated fl ying to LVC will damage the battery.

Tip: Monitor your aircraft battery’s voltage before and after fl ying by using a

Li-Po Cell Voltage Checker (EFLA111, sold separately).

Flying

Fly the aircraft and trim it for level fl ight in Precision Mode at 3/4 throttle. After landing, adjust the linkages mechanically to account for trim changes and then reset the trims to neutral. Ensure the aircraft will fl y straight and level with no trim or sub-trim.

Night Flying

Fly in an open and familiar fl ying area, where there are no obstacles to night fl ying. Switch ON the LED switch in the battery compartment.

For your fi rst night fl ights, start in low light conditions, not complete darkness.

Landing

For your fi rst fl ights with the recommended battery pack (EFLB22003S30), set your transmitter timer or a stopwatch to 4 minutes. After fi ve minutes, land the aircraft. Adjust your timer for longer or shorter fl ights once you have fl own the model. If at any time the motor pulses, land the aircraft immediately to

recharge the fl ight battery. See the Low Voltage Cutoff (LVC) section for more details on maximizing battery health and run time.

To land the aircraft, fl y the aircraft down to the ground using 1/4 –1/3 throttle to allow for enough energy for a proper fl are. The aircraft is easiest to land doing a wheel landing (two point), where the aircraft touches down on the main landing gear fi rst while the tailwheel is still off the ground. The aircraft

Repairs

Thanks to the Z-Foam ™ material in this aircraft, repairs to the foam can be made using virtually any adhesive (hot glue, regular CA, epoxy, etc). When parts are not repairable, see the Replacement Parts List for ordering by item number.

For a listing of all replacement and optional parts, refer to the list at the end of this manual.

NOTICE: Use of CA accelerant on your aircraft can damage paint. DO NOT handle the aircraft until accelerant fully dries.

13

EN

EN

Guidlines for Flying 3D

Getting Started

This aircraft and its SAFE ® system were designed together to help an intermediate pilot apply standard fl ying skills to the demands of 3D fl ying. The calmer the wind conditions, the easier it is to execute maneuvers.

Select the SAFE fl ight mode that supports the maneuver you want to perform.

Hold the panic recovery button/switch to help you escape diffi culty in a maneuver. You may want to fl y low airspeed, high rate maneuvers at an altitude that allows you space to escape into forward fl ight. For your fi rst hover attempts, fl y with the canopy toward you for easier orientation.

When you fl y 3D, manage your throttle smoothly, but quickly respond to keep your model in the air and oriented the direction you want. If desired, use spotters to keep others from distracting you. Advanced 3D maneuvers always seem to attract a curious audience.

Building Your Skills

Increasing your skills takes time. Practice regularly and try following a plan for increasing your skills. Mastering one maneuver at a time may be more benefi cial than trying to learn everything all at once. Always stay aware of your aircraft’s performance in different conditions and attitudes:

What response can you consistently get from your aircraft?

• Set up your aircraft for consistent response in all attitudes and fl ight

conditions where you choose to fl y. Not all challenges are due to the equipment, just as not all challenges are due to the pilot’s skills.

• If you feel you reach a plateau in your skills, see if you have built the right habits in the fundamentals of 3D fl ying. Play to your strengths and the strengths of your aircraft while minimizing reliance on areas of weakness.

• Know yourself and your equipment well enough so you can confi dently

take on greater challenges. Push yourself, but avoid pushing past your aircraft’s performance envelope.

• Seek fun ways to safely share your enjoyment of 3D fl ying.

You may want to master the Harrier fi rst, an essential maneuver used to enter and exit other 3D maneuvers.

Advanced 3D Maneuvers

Harrier:

Inverted

Harrier:

Hover:

Torque Roll

Harrier Roll:

Waterfall:

Inverted

Waterfall:

The aircraft fl ies forward slowly in a nose high (approximately 45 degrees) attitude.

The inverted aircraft fl ies forward slowly in a nose high (approximately 45 degrees) attitude.

The aircraft nose is pointed up while the prop thrust keeps the model in the air with little or no change in altitude.

The aircraft hovers with little or no change in altitude while rotating left around its roll axis.

The aircraft does a harrier while rotating around its roll axis.

The aircraft turns over completely (360 degrees) in the pitch axis with very little forward motion or change in altitude.

The inverted aircraft turns over completely (360 degrees) in the pitch axis with very little forward motion or change in altitude.

Post Flight

1

Disconnect the fl ight battery from the ESC (Required for Safety and battery life).

2 Power OFF the transmitter.

3 Remove the fl ight battery from the aircraft.

4 Recharge the fl ight battery.

5 Repair or replace all damaged parts.

6

Store the fl ight battery apart from the aircraft and monitor the battery charge.

7

Make note of the fl ight conditions and fl ight plan results, planning for future fl ights.

14

Power Component Service

CAUTION: Always disconnect the fl ight battery before performing motor service.

Disassembly

1. Remove the screw (A) and spinner (B) from the collet (G).

2. Remove the spinner nut (C), propeller (D), backplate (E) and collet from the motor shaft (H). You will need a tool to turn the spinner nut.

3. Remove 3 screws (I) from the cowling (J). Carefully remove the cowling from the fuselage. Paint may keep the cowling attached to the fuselage.

4. Remove the 4 screws (K) from the motor mount (L) and the fuselage.

5. Disconnect the motor wires from the ESC wires.

6. Remove the 4 screws (M) and motor (N) from the motor mount.

Assembly

Assemble in reverse order.

• Correctly align and connect the motor wire colors with the ESC wires.

• The propeller size numbers (12 x 4) must face out from the motor for correct propeller operation.

• A tool is required to tighten the lock nut on the collet.

A B C E G I J

H N

D

K L

Not all wiring shown.

M

EN

Troubleshooting Guide SAFE

Problem Possible Cause

Flying too fast in 3D mode

Flying over recommended airspeed

Change to Precision Mode

Reduce air speed

Solution

Oscillation

Damaged propeller or spinner Replace propeller or spinner

Imbalanced propeller

Balance the propeller. For more information, view John Redman’s propeller balancing video at www.

horizonhobby.com

Motor vibration

Loose receiver

Loose aircraft controls

Worn parts

Irregular servo movement

Trim change when fl ight mode is switched

Incorrect response to the AS3X Control

Direction Test

Receiver did not save trim

Incorrect direction settings in the receiver, which can cause a crash

Replace parts or correctly align all parts and tighten fasteners as needed

Align and secure receiver in fuselage

Tighten or otherwise secure parts (servo, arm, linkage, horn and control surface)

Replace worn parts (especially propeller, spinner or servo)

Replace servo

After adjusting transmitter trim in the air or on the ground, do not touch the control sticks for 2 seconds

DO NOT fl y. Correct the direction settings (refer to the receiver manual), then fl y

15

EN

Troubleshooting Guide

Problem Possible Cause Solution

Aircraft will not respond to throttle but responds to other controls

Extra propeller noise or extra vibration

Throttle not at idle and/or throttle trim too high

Throttle servo travel is lower than 100%

Throttle channel is reversed

Motor disconnected from ESC

Damaged propeller and spinner, collet or motor

Propeller is out of balance

Prop nut is too loose

Spinner is not tight or fully seated in place

Flight battery charge is low

Reset controls with throttle stick and throttle trim at lowest setting

Make sure throttle servo travel is 100% or greater

Reverse throttle channel on transmitter

Make sure motor is connected to the ESC

Replace damaged parts

Balance or replace propeller

Tighten the prop nut

Tighten the spinner or remove the spinner and turn it 180 degrees

Completely recharge fl ight battery

Reduced fl ight time or aircraft underpowered

Aircraft will not Bind

(during binding) to transmitter

Aircraft will not connect (after binding) to transmitter

Propeller installed backwards

Flight battery damaged

Flight conditions may be too cold

Battery capacity too low for flight conditions

Install propeller with numbers facing forward

Replace fl ight battery and follow fl ight battery instructions

Make sure battery is warm before use

Transmitter too near aircraft during binding process

Flight battery/transmitter battery charge is too low

Bind switch or button not held long enough during bind process

Transmitter too near aircraft during connecting process

Aircraft or transmitter is too close to large metal object, wireless source or another transmitter

Replace battery or use a larger capacity battery

Move powered transmitter a few feet from aircraft, disconnect and reconnect fl ight battery to aircraft

Aircraft or transmitter is too close to large metal object, wireless source or another transmitter

Move aircraft and transmitter to another location and attempt binding again

The bind plug is not installed correctly in the bind port Install bind plug in bind port and bind the aircraft to the transmitter

Replace/recharge batteries

Power off transmitter and repeat bind process. Hold transmitter bind button or switch until receiver is bound

Move powered transmitter a few feet from aircraft, disconnect and reconnect fl ight battery to aircraft

Move aircraft and transmitter to another location and attempt connecting again

Bind plug left installed in bind port

Aircraft bound to different model memory

(ModelMatch TM radios only)

Rebind transmitter to the aircraft and remove the bind plug before cycling power

Select correct model memory on transmitter

Replace/recharge batteries

Control surface does not move

Flight battery/Transmitter battery charge is too low

Transmitter may have been bound to a different aircraft using different DSM protocol

Control surface, control horn, linkage or servo damage

Wire damaged or connections loose

Transmitter is not bound correctly or the incorrect airplanes was selected

Flight battery charge is low

BEC (Battery Elimination Circuit) of the ESC is damaged

Bind aircraft to transmitter

Replace or repair damaged parts and adjust controls

Do a check of wires and connections, connect or replace as needed

Re-bind or select correct airplanes in transmitter

Fully recharge fl ight battery

Replace ESC

Controls reversed

Motor power pulses then motor loses power

Transmitter settings are reversed

ESC uses default soft Low Voltage Cutoff (LVC)

Weather conditions might be too cold

Battery is old, worn out, or damaged

Battery C rating might be too small

Perform the Control Direction Test and adjust the controls on transmitter appropriately

Recharge fl ight battery or replace battery that is no longer performing

Postpone flight until weather is warmer

Replace battery

Use recommended battery

16

AMA National Model Aircraft Safety Code

Effective January 1, 2014

A. GENERAL

A model aircraft is a non-human-carrying aircraft capable of sustained fl ight in the atmosphere. It may not exceed limitations of this code and is intended exclusively for sport, recreation, education and/or competition. All model fl ights must be conducted in accordance with this safety code and any additional rules specifi c to the fl ying site.

B. RADIO CONTROL

1. All pilots shall avoid fl ying directly over unprotected people, vessels, vehicles or structures and shall avoid endangerment of life and property

1. Model aircraft will not be fl own:

(a) In a careless or reckless manner.

(b) At a location where model aircraft activities are prohibited.

2. Model aircraft pilots will:

(a) Yield the right of way to all man carrying aircraft.

(b) See and avoid all aircraft and a spotter must be used when appropriate.

(AMA Document #540-D.)

(c) Not fl y higher than approximately 400 feet above ground level within three (3) miles of an airport, without notifying the airport operator.

(d) Not interfere with operations and traffi c patterns at any airport, heliport or seaplane base except where there is a mixed use agreement.

(e) Not exceed a takeoff weight, including fuel, of 55 pounds unless in compliance with the AMA Large Model Aircraft program. (AMA

2. A successful radio equipment ground-range check in accordance with manufacturer’s recommendations will be completed before the fi rst fl ight of a new or repaired model aircraft.

3. At all fl ying sites a safety line(s) must be established in front of which all fl ying takes place (AMA Document #706.)

(a) Only personnel associated with fl ying the model aircraft are allowed at or in front of the safety line.

(b) At air shows or demonstrations, a straight safety line must be

established.

(c) An area away from the safety line must be maintained for spectators.

(d) Intentional fl ying behind the safety line is prohibited.

4. RC model aircraft must use the radio-control frequencies currently allowed by the Federal Communications Commission (FCC). Only individuals properly licensed by the FCC are authorized to operate equipment on

Amateur Band frequencies.

(f) Ensure the aircraft is identifi ed with the name and address or AMA number of the owner on the inside or affi xed to the outside of the model aircraft. (This does not apply to model aircraft fl own indoors).

(g) Not operate aircraft with metal-blade propellers or with gaseous boosts except for helicopters operated under the provisions of AMA Document

#555.

(h) Not operate model aircraft while under the infl uence of alcohol or while using any drug which could adversely affect the pilot’s ability to safely control the model.

(i) Not operate model aircraft carrying pyrotechnic devices which explode or burn, or any device which propels a projectile or drops any object that creates a hazard to persons or property.

Exceptions:

• Free Flight fuses or devices that burn producing smoke and are

securely attached to the model aircraft during fl ight.

• Rocket motors (using solid propellant) up to a G-series size may

be used provided they remain attached to the model during fl ight.

Model rockets may be fl own in accordance with the National

Model Rocketry Safety Code but may not be launched from

5. RC model aircraft will not operate within three (3) miles of any pre-existing fl ying site without a frequency-management agreement (AMA Documents

#922 and #923.)

6. With the exception of events fl own under offi cial AMA Competition

Regulations, excluding takeoff and landing, no powered model may be fl own outdoors closer than 25 feet to any individual, except for the pilot and the pilot’s helper(s) located at the fl ight line.

7. Under no circumstances may a pilot or other person touch a model aircraft in fl ight while it is still under power, except to divert it from striking an

individual.

8. RC night fl ying requires a lighting system providing the pilot with a clear view of the model’s attitude and orientation at all times. Hand-held illumi- nation systems are inadequate for night fl ying operations.

9. The pilot of a RC model aircraft shall:

(a) Maintain control during the entire fl ight, maintaining visual contact without enhancement other than by corrective lenses prescribed for • Offi cially designated AMA Air Show Teams (AST) are authorized to

use devices and practices as defi ned within the Team AMA

Program Document (AMA Document #718).

(j) Not operate a turbine-powered aircraft, unless in compliance with the

AMA turbine regulations. (AMA Document #510-A).

(b) Fly using the assistance of a camera or First-Person View (FPV) only in accordance with the procedures outlined in AMA Document #550.

(C) Fly using the assistance of autopilot or stabilization system only in accordance with the procedures outlined in AMA Document #560.

3. Model aircraft will not be fl own in AMA sanctioned events, air shows or model demonstrations unless:

(a) The aircraft, control system and pilot skills have successfully demonstrated all maneuvers intended or anticipated prior to the

Please see your local or regional modeling association’s guidelines for proper, safe operation of your model aircraft.

(b) An inexperienced pilot is assisted by an experienced pilot.

4. When and where required by rule, helmets must be properly worn and fastened. They must be OSHA, DOT, ANSI, SNELL or NOCSAE approved or comply with comparable standards.

EN

17

EN

Limited Warranty

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage,

(ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modifi cation of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v)

Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations. for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.com/content/_service-center_renderservice-center. If you do not have internet access, please contact Horizon

Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER

WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL

IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED

WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY

ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE

REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER

THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL

OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR

COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS

BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR

ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF

THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, fi nal assembly, modifi cation or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.

Law

These terms are governed by Illinois law (without regard to confl ict of law principals). This warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.

NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please contact the appropriate Horizon Product

Support offi ce.

Warranty Requirements

For Warranty consideration, you must include your original sales

receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of

Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be completed and payment will be required without notifi cation or estimate of the expense unless the expense exceeds 50% of the retail

purchase cost. By submitting the item for service you are agreeing to payment of the service without notifi cation. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American

Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby.com/content/_service-center_render-servicecenter.

ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold noncompliant Product for a period of 60 days from notifi cation, after which it will be discarded.

WARRANTY SERVICES

Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service

Contact Information section to speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online

Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance

18

Contact Information

Country of Purchase

United States of

America

United Kingdom

Germany

France

China

Horizon Hobby

Horizon Service Center

(Repairs and Repair Requests)

Horizon Product Support

(Product Technical Assistance)

Sales

Service/Parts/Sales:

Horizon Hobby Limited

Horizon Technischer Service

Sales: Horizon Hobby GmbH

Service/Parts/Sales:

Horizon Hobby SAS

Service/Parts/Sales:

Horizon Hobby – China

Phone Number/Email Address servicecenter.horizonhobby.com/

RequestForm/ www.quickbase.com/db/ bghj7ey8c?a=GenNewRecord

888-959-2305 [email protected]

888-959-2305 [email protected]

+44 (0) 1279 641 097 [email protected]

+49 (0) 4121 2655 100 [email protected]

+33 (0) 1 60 18 34 90 [email protected]

+86 (021) 5180 9868

IC Information

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not

Address

4105 Fieldstone Rd

Champaign, Illinois, 61822 USA

Units 1–4 , Ployters Rd, Staple Tye

Harlow, Essex, CM18 7NS, United Kingdom

Christian-Junge-Straße 1

25337 Elmshorn, Germany

11 Rue Georges Charpak

77127 Lieusaint, France

Room 506, No. 97 Changshou Rd.

Shanghai, China 200060

FCC Information

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifi cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.

cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Compliance Information for the European Union

Declaration of Conformity

(in accordance with ISO/IEC 17050-1)

No. HH2014092602

NightVisionAire

Item Number(s): EFL7150

Equipment class: 1

The object of declaration described above is in conformity with the requirements of the specifi cations listed below, following the provisions of the European R&TTE directive 1999/5/EC and EMC Directive 2004/108/EC:

EN301 489-1 V1.9.2: 2012

EN301 489-17 V2.1.1: 2009

Instructions for disposal of WEEE by users in the

European Union

This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city offi ce, your household waste disposal service or where you purchased the product.

EN55022:2010 + AC:2011

EN55024:2010

EN

Signed for and on behalf of:

Horizon Hobby, LLC

Champaign, IL USA

September 26, 2014

Mike Dunne

Executive Vice President Product Divisions

Horizon Hobby, LLC

19

IT

Informazioni per i contatti

Paese di acquisto

Germania

Horizon Hobby

Horizon Technischer Service

Sales: Horizon Hobby GmbH

Telefono / indirizzo e-mail [email protected]

+49 (0) 4121 2655 100

Indirizzo

Christian-Junge-Straße 1

25337 Elmshorn, Germania

Informazioni sulla conformità per l’Unione Europea

Dichiarazione di conformità

(in conformità con ISO/IEC 17050-1))

No. HH2014092602

Codice componente:

Classe dei dispositivi:

EFL7150

1

L’oggetto della dichiarazione di cui sopra è conforme ai requisiti delle specifi che elencate qui di seguito, secondo le disposizioni delle direttive europee R&TTE 1999/5/EC e EMC 2004/108/EC:

EN301 489-1 V1.9.2: 2012

EN301 489-17 V2.1.1: 2009

Istruzioni per lo smaltimento RAEE da parte degli utenti dell’Unione Europea

Questo prodotto non deve essere smaltito assieme ai rifi uti domestici. Al contrario, l’utente è responsabile dello smaltimento di tali rifi uti, che devono essere portati in un centro di raccolta designato per il riciclaggio di rifi uti elettrici e apparecchiature elettroniche.

La raccolta differenziata e il riciclaggio di tali rifi uti provenienti da apparecchiature, nel momento dello smaltimento aiuteranno a preservare le risorse naturali e garantiranno un riciclaggio adatto a proteggere il benessere dell’uomo e dell’ambiente. Per maggiori informazioni sui centri di raccolta, contattare il proprio uffi cio locale, il servizio di smaltimento rifi uti o il negozio presso il quale è stato acquistato il prodotto.

EN55022:2010 + AC:2011

EN55024:2010

Firmato a nome e per conto di:

Horizon Hobby LLC

Champaign IL USA

26 settembre 2014

Mike Dunne

Executive Vice President Product Divisions

Horizon Hobby, LLC

70

Replacement Parts • Ersatzteile • Pièces de rechange • Pezzi di ricambio

Part # | Nummer

Numéro | Codice

Description Beschreibung Description Descrizione

EFL7138

EFL7108

PKZ6503

PKZ6521

EFL7113

PKZ6537

PKZ6533

EFL7167

PKZ6528

EFL7120

EFL7124

EFL7125

PKZ6529

EFL7126

EFLM7225

EFLM72252

EFLA1040LB

SPMAR636

Decal Set: NIGHTVisionAire

Spinner: NIGHTVisionAire

Landing gear set: VisionAire

Dekorbogen: NIGHTVisionAire

Spinner: NIGHTVisionAire

Fahrwerk-Set: VisionAire

Planche de décalcomanies : NIGHTVisionAire

Cône : NIGHTVisionAire

Jeu de train d'atterrissage principal :

VisionAire

Foglio con decalcomanie: NIGHTVisionAire

Ogiva: NIGHTVisionAire

Set del carrello di atterraggio: Vision-

Aire

Wing & H. Tail Tube: NIGHTVisionAire

Hatch Set: NIGHTVisionAire

Parkzone VisionAire: Tragfl ächen- und

Leitwerksverbinder

E-fl ite NIGHTvisionaire: Sender- u.

Akkuklappe

Parkzone VisionAire SFG Set

Clé d’aile et de stabilisateur : VisionAire Ala & tubo coda orizz: NIGHTVisionAire

Set de trappes : NIGHTVisionAire Set portello: NIGHTVisionAire

SFG Set: VisionAire Set de SFG : VisionAire Set SFG: VisionAire

Horns & Pushrod: VisionAire

Parkzone VisionAire Ruderhorn und

Gestängeset

Tringleries et guignols : VisionAire Squadrette e comandi: VisionAire

Fuselage w/ LED’s: NIGHTVisionAire E-fl ite NIGHTvisionaire: Rumpf m. LEDs Fuselage avec DELs : NIGHTVisionAire Fusoliera con LED: NIGHTVisionAire

Motor mount: VisionAire Parkzone VisionAire Motorträger Support moteur : VisionAire

Wing Set w/LED’s: NIGHTVisionAire E-fl ite NIGHTvisionaire: Tragfl ächen

Horizontal Tail w/LED’s: NIGHTVisionAire

Rudder: NIGHTVisionAire

E-fl ite NIGHTVisionAire: Höhenleitwerk m. LEDs

E-fl ite NIGHTvisionaire: Seitenruder

Tray & Gear Mount: VisionAire

Cowl: NIGHTVisionAire

BL10 Motor: VisionAire

Prop Adapter: VisionAire

40-Amp Lite Pro Switch-Mode BEC

Brushless ESC (V2)

Spektrum 6-Channel AS3X Sport

Receiver

Parkzone VisionAire Akkuträger und

Fahrwerksabdeckung

E-fl ite NIGHTVisionaire: Motorhaube

E-fl ite BL10 Brushless Aussenläufer,

1,250 Kv

E-Flite VisionAire: Propelleradapter

E-fl ite 40-Amp Pro Switch-Mode BEC

Brushless Regler (V2)

Spektrum AR636 6-Kanal AS3X Sport

Empfänger

Ailes avec DELs : NIGHTVisionAire

Stabilisateur avec DELs : NIGHTVisionAire

Dérive : NIGHTVisionAire

Support de train d’atterrissage :

VisionAire

Capot : NIGHTVisionAire

Moteur BL10 : VisionAire

Adaptateur d’hélice : VisionAire

Contrôleur Brushless 40A Lite Pro

Switch mode BEC V2

Récepteur Spektrum 6 voies avec

AS3X

Supporto del motore: VisionAire

Set ala con LED: NIGHTVisionAire

Piano di coda orizzontale c/LED:

NIGHTVisionAire

Timone: NIGHTVisionAire

Sede e supporto carrello: VisionAire

Capottina motore: NIGHTVisionAire

Motore BL10: VisionAire

Adattatore elica: VisionAire

ESC brushless 40-Amp Lite Pro BEC a commutazione

Ricevitore sport AS3X Spektrum 6 canali

EFLP12040E Propeller: 12 x 4E Propeller: 12 x 4E Hélice 12x4E Elica: VisionAire

EFLR7155 13 g Digital Micro Servo

EFLM72251 BL10 Motor Shaft: VisionAire

EFLA631 LED power unit: NIGHTVisionAire

E-fl ite 13g Digital Micro Servo Micro servo digital 13g

E-Flite VisionAire: Motorwelle Axe de moteur BL10

E-fl ite NIGHTVisionAire: LED Powereinheit Module d’éclairage : NIGHTVisionAire

Micro servo digitale 13g

Albero motore BL10: VisionAire

Unità alimentazione LED: NIGHTVisionAire

Optional Parts • Optionale Bauteile • Pièces optionnelles • Pezzi opzionali

Part # | Nummer

Numéro | Codice

EFLA250

EFLAEC302

EFLAEC303

EFLC3025

EFLC3020

EFLC4010

DYNC2010CA

Description Beschreibung Description

Park Flyer Tool Assortment, 5 pc Park Flyer Werkzeugsortiment, 5 teilig Assortiment d'outils park fl yer, 5pc

EC3 Battery Connector, Female (2) EC3 Akkukabel, Buchse (2) Prise EC3 femelle (2pc)

EC3 Device/Battery Connector,

Male/Female

EC3 Kabelsatz, Stecker/Buchse Prise EC3 male/femelle

Celectra 80W AC/DC

Multi-Chemistry Battery Charger

200W DC multi-chemistry battery charger

Celectra 15VDC

250W Power Supply

Prophet Sport Plus 50W AC DC

Charger

Celectra 80 W AC/DC

Multi-Chemistry-Batterieladegerät

200W DC Multi-Batterie Ladegerät - EU Chargeur multiple DC 200W

Celectra 15 V DC

250-W-Netzstecker

Dynamite Ladegerät Prophet Sport

Plus 50W AC/DC EU

Chargeur de batterie AC/DC

Celectra 80 W multi-types

Alimentation Celectra

CC 15 V 250 W

Chargeur Prophet Sport Plus 50W AC

DC

Descrizione

Park Flyer assortimento attrezzi, 5 pc

EC3 Connettore femmina x batteria

(2)

EC3 Connettore batteria maschio/ femmina

Caricabatterie per batteria multichimica 80 W c.a./c.c.

200W DC Caricabatterie universale

Alimentatore Celectra 15V c.c., 250

W

Caricabatterie Prophet Sport Plus

50W AC DC

EFLA111

DYN1405

DYN1400

Li-Po Cell Voltage Checker Li-Po Cell Voltage Checker Testeur de tension d’éléments Li-Po

Li-Po Charge Protection Bag,

Large

Li-Po Charge Protection Bag,

Small

DX4e DSMX 4-Channel Transmitter

DX5e DSMX 5-Channel Transmitter

Dynamite LiPoCharge Protection Bag groß

Dynamite LiPoCharge Protection Bag klein

Spektrum DX4e DSMX 4 Kanal sender ohne Empfänger

Spektrum DX5e DSMX 5 Kanal sender ohne Empfänger

Sac de charge Li-Po, grand modèle.

Sac de charge Li-Po, petit modèle

Emetteur DX4e DSMX 4 voies

Emetteur DX5e DSMX 5 voies

DX6i DSMX 6-Channel Transmitter Spektrum DX6i DSMX 6-Kanal Sender Emetteur DX6i DSMX 6 voies

DX6 DSMX 6-Channel Transmitter Spektrum DX6 DSMX 6-Kanal Sender Emetteur DX6 DSMX 6 voies

DX7s DSMX 7-Channel Transmitter Spektrum DX7s DSMX 7 Kanal Sender Emetteur DX7s DSMX 7 voies

DX8 DSMX 8-Channel Transmitter Spektrum DX8 DSMX 8 Kanal Sender Emetteur DX8 DSMX 8 voies

DX9 DSMX 9-Channel Transmitter Spektrum DX9 DSMX 9 Kanal Sender Emetteur DX9 DSMX 9 voies

DX18 DSMX 18-Channel

Transmitter

Spektrum DX18 DSMX 18 Kanal

Sender

Emetteur DX18 DSMX 18 voies

Voltmetro verifi ca batterie LiPo

Sacchetto grande di protezione per carica LiPo

Busta protezione piccola par LiPo

DX4e DSMX Trasmettitore 4 canali

DX5e DSMX Trasmettitore 5 canali

DX6i DSMX Trasmettitore 6 canali

DX6 DSMX Trasmettitore 6 canali

DX7s DSMX Trasmettitore 7 canali

DX8 DSMX Trasmettitore 8 canali

DX9 DSMX Trasmettitore 9 canali

DX18 DSMX Trasmettitore 18 canali

71

© 2014 Horizon Hobby, LLC.

E-fl ite, VisionAire, SAFE, the SAFE logo, AS3X, DSM, DSM2, DSMX, the DSMX logo, the BNF logo, Z-Foam, ModelMatch, EC3, Celectra and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.

The Spektrum trademark is used with permission of Bachmann Industries, Inc.

Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan.

All other trademarks, service marks and logos are property of their respective owners.

Patents pending.

http://www.e-fl iterc.com/

EFL7150 Created 11/14 44762