HT-J7500W
HT-J7750W
User manual
Blu-ray™
Home Entertainment System
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register your product at
www.samsung.com/register
This Nanum Gothic Eco font is provided by NAVER.
Safety Information
✎✎ The following also applies to the Wireless Receiver Module (SWA-7000).
This symbol indicates that high voltage
is present inside. It is dangerous to
make any kind of contact with any
internal part of this product.
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE THE COVER (OR BACK). THERE ARE NO
USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO
QUALIFIED PERSONNEL.
●●
●●
●●
●●
●●
●●
●●
The slots and openings in the cabinet and in
the back or bottom are provided for necessary
ventilation. To ensure reliable operation of this
apparatus, and to protect it from overheating,
these slots and openings must never be blocked or
covered.
-- Do not place this apparatus in a confined space,
such as a bookcase, or built-in cabinet, unless
proper ventilation is provided.
-- Do not place this apparatus near or over a
radiator or heat register, or where it is exposed
to direct sunlight.
-- Do not place vessels (vases etc.) containing
water on this apparatus. A water spill can cause
a fire or electric shock.
Do not expose this apparatus to rain or place it
near water (near a bathtub, washbowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool, etc.). If this apparatus accidentally
gets wet, unplug it and contact an authorized
dealer immediately.
This apparatus uses batteries. In your community,
there might be environmental regulations that
require you to dispose of these batteries properly.
Please contact your local authorities for disposal or
recycling information.
Do not overload wall outlets, extension cords or
adaptors beyond their capacity, since this can result
in fire or electric shock.
Route power-supply cords so that they are not
likely to be walked on or pinched by items placed
on or against them. Pay particular attention to
cords at the plug end, at wall outlets, and the point
where they exit from the apparatus.
To protect this apparatus from a lightning storm,
or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will
prevent damage to the set due to lightning and
power line surges.
Before connecting the AC power cord to the DC
adaptor outlet, make sure the voltage designation
of the DC adaptor corresponds to the local
electrical supply.
This symbol indicates that important
literature concerning operation and
maintenance has been included with
this product.
●●
●●
●●
●●
●●
●●
●●
●●
Never insert anything metallic into the open parts
of this apparatus. Doing so may create a danger of
electric shock.
To avoid electric shock, never touch the inside of
this apparatus. Only a qualified technician should
open this apparatus.
Make sure to plug the power cord in until it is
firmly seated. When unplugging the power cord
from a wall outlet, always pull on the power cord's
plug. Never unplug by pulling on the power cord.
Do not touch the power cord with wet hands.
If this apparatus does not operate normally - in
particular, if there are any unusual sounds or smells
coming from it - unplug it immediately and contact
an authorized dealer or service centre.
Maintenance of Cabinet.
-- Before connecting other components to this
product, be sure to turn them off.
-- If you move your product suddenly from a cold
place to a warm place, condensation may occur
on the operating parts and lens and cause
abnormal disc playback. If this occurs, unplug the
product, wait for two hours, and then connect
the plug to the power outlet. Then, insert the
disc, and try to play back again.
Be sure to pull the power plug out of the outlet
if the product is to remain unused or if you are
leaving the house for an extended period of time
(especially when children, elderly, or disabled
people will be left alone in the house).
-- Accumulated dust can cause an electric shock,
an electric leakage, or a fire by causing the
power cord to generate sparks and heat or the
insulation to deteriorate.
Contact an authorized service centre for
information if you intend to install your product
in a location with heavy dust, high or low
temperatures, high humidity, chemical substances,
or where it will operate 24 hours a day such as in
an airport, a train station, etc. Failing to do so may
lead to serious damage of your product.
Use only a properly grounded plug and wall outlet.
-- An improper ground may cause electric shock or
equipment damage. (Class l Equipment only.)
2 - English
●●
●●
●●
●●
●●
●●
●●
●●
●●
WARNING :
●● TO PREVENT THE SPREAD OF FIRE,
KEEP CANDLES AND OTHER ITEMS
WITH OPEN FLAMES AWAY FROM
THIS PRODUCT AT ALL TIMES.
●● To reduce the risk of fire or electric
shock, do not expose this appliance to rain or
moisture.
CLASS 1 LASER product
This product is classified as a CLASS 1 LASER product.
Use of controls, adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION :
●● INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED, AVOID EXPOSURE TO
BEAM.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1 PRODUCTO
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
LÁSER CLASE 1
3D Precautions
IMPORTANT HEALTH AND SAFETY INFORMATION
FOR 3D PICTURES.
Read and understand the following safety
information before using the 3D function.
●● Some viewers may experience discomfort while
viewing 3D TV such as dizziness, nausea, and
headaches.
If you experience any such symptom, stop viewing
3D TV, remove the 3D Active Glasses, and rest.
●● Watching 3D images for an extended period of
time may cause eye strain. If you feel eye strain,
stop viewing 3D TV, remove your 3D Active
Glasses, and rest.
●● A responsible adult should frequently check on
children who are using the 3D function.
If there are any reports of tired eyes, headaches,
dizziness, or nausea, have the child stop viewing
3D TV and rest.
●● Do not use the 3D Active Glasses for other
purposes (such as general eyeglasses, sunglasses,
protective goggles, etc.)
●● Do not use the 3D function or 3D Active Glasses
while walking or moving around. Using the 3D
function or 3D Active Glasses while moving around
may cause you to bump into objects, trip, and/or
fall, and cause serious injury.
●● If you want to enjoy 3D content, connect a 3D
device (3D compliant AV receiver or TV) to the
product’s HDMI OUT port using a high-speed HDMI
cable. Put on 3D glasses before playing the 3D
content.
●● The product outputs 3D signals only through an
HDMI cable connected to the HDMI OUT port.
●● The video resolution in 3D play mode is limited to
the resolution of the original 3D video. You cannot
change the resolution to your preference.
●● Some functions such as BD Wise, screen size
adjustment, and resolution adjustment may not
operate properly in 3D play mode.
●● You must use a high-speed HDMI cable for proper
output of the 3D signal.
●● Stay at least three times the width of the screen
from the TV when watching 3D images. For
example, if you have a 46 inch screen, stay 3.5
meters from the screen.
●● Place the 3D video screen at eye level for the best
3D picture.
●● When the product is connected to some 3D
devices, the 3D effect may not function properly.
●● This product does not convert 2D content into 3D.
●● "Blu-ray 3D" and "Blu-ray 3D" logo are trademarks
of the Blu-ray Disc Association.
3 - English
Safety Information
●●
To turn this apparatus off completely, you must
disconnect it from the wall outlet. Consequently,
the wall outlet and power plug must be readily
accessible at all times.
Do not allow children to hang on the product.
Store the accessories (battery, etc.) in a location
safely out of the reach of children.
Do not install the product in an unstable location
such as a shaky self, a slanted floor, or a location
exposed to vibration.
Do not drop or strike the product. If the product is
damaged, disconnect the power cord and contact
a service centre.
To clean this apparatus, unplug the power cord
from the wall outlet and wipe the product using
a soft, dry cloth. Do not use any chemicals such
as wax, benzene, alcohol, thinners, insecticide,
air fresheners, lubricants, or detergent. These
chemicals can damage the appearance of the
product or erase the printing on the product.
Do not expose this apparatus to dripping or
splashing. Do not put objects filled with liquids,
such as vases on the apparatus.
Do not dispose of batteries in a fire.
Do not plug multiple electric devices into the same
wall socket. Overloading a socket can cause it to
overheat, resulting in a fire.
There is danger of an explosion if you replace
the batteries used in the remote with the wrong
type of battery. Replace only with the same or
equivalent type.
Contents
Getting Started
Playing Content
5
Accessories
28 Playing Commercial Discs
5
Speaker Components
28 Playing Multimedia Files
6
Front Panel
30 Controlling Video Playback
7
Rear Panel
33 Controlling Music Playback
8
Remote Control
38 Using Bluetooth
40 Playing Photo Content
Connections
9
42 Using the Special Effects Remote Control
Buttons
Connecting the Speakers
13 Connecting to a TV and External Devices
Network Services
14 Connecting to a Network Router
43 Logging In to Your Samsung Account
Settings
43 Before Using SAMSUNG APPS
15 The Initial Settings Procedure
44 Using SAMSUNG APPS
15 The Home Screen at a Glance
46 Screen Mirroring
16 Accessing the Settings Screen
46 Using the Web Browser
16 Settings Menu Functions
22 Radio Setup
50 Linking your Internet Service Accounts to the
Product
23 Network Setup
50 BD-LIVE™
25 Wi-Fi Direct
Appendix
26 Upgrading Software
51 Additional Information
52 Disk and Format Compatibility
59 Troubleshooting
62 Specifications
64 Licences
Wiring the Main Power Supply Plug (UK Only)
IMPORTANT NOTICE : The mains lead on this equipment is supplied with a moulded plug incorporating
a fuse. The value of the fuse is indicated on the pin face of the plug and if it requires replacing, a fuse
approved to BS1362 of the same rating must be used. Never use the plug with the fuse cover removed. If
the cover is detachable and a replacement is required, it must be of the same colour as the fuse fitted in
the plug. Replacement covers are available from your dealer. If the fitted plug is not suitable for the power
points in your house or the cable is not long enough to reach a power point, you should obtain a suitable
safety approved extension lead or consult your dealer for assistance. However, if there is no alternative to
cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a
mains socket as there is a risk of shock hazard from the bared flexible cord. Never attempt to insert bare
wires directly into a mains socket. A plug and fuse must be used at all times.
IMPORTANT : The wires in the mains lead are coloured in accordance with the following code:– BLUE =
NEUTRAL BROWN = LIVE As these colours may not correspond to the coloured markings identifying the
terminals in your plug, proceed as follows:–The wire coloured BLUE must be connected to the terminal
marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the
terminal marked with the letter L or coloured BROWN or RED.
IMPORTANT : DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH LETTER
E OR BY THE EARTH SYMBOL U, OR COLOURED GREEN OR GREEN AND YELLOW.
4 - English
Getting Started
■■
■■
Getting Started
■■
Figures and illustrations in this User Manual are provided for reference only and may differ from
actual product appearance.
An administration fee may be charged if either
a.an engineer is called out at your request and there is no defect in the product (i.e. where you
have failed to read this user manual)
b.you bring the unit to a repair centre and there is no defect in the product (i.e. where you have
failed to read this user manual).
The amount of such administration charge will be advised to you before any work or home visit is
carried out.
Check the box for the accessories and speaker components listed or shown below.
Accessories
●●
Remote Control
●●
Lithium Battery
Power Cable (Main Unit, SWA-7000) x 2
●●
User Manual
FM Antenna
WARNING, DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD,
[The remote control supplied with] This product contains a coin/button cell battery.
If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and
can lead to death. Keep new and used batteries away from children. If the battery compartment does
not close securely, stop using the product and keep it away from children. If you think batteries might
have been swallowed or placed inside any part of the body, seek immediate medical attention.
Speaker Components
HT-J7500W - 5.1CH
Centre
L
R
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
ID SET
Front x 2
Surround x 2
Speaker Cable x 6
5 - English
Subwoofer
Wireless Receiver
Module (SWA-7000)
Getting Started
HT-J7750W - 7.1CH
Speaker Cable x 2
Screw (5x20) x 16
Stand Base x 4
Centre
L
R
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
D
H-EN
HIG
D
H-EN
HIG
Front/
Front Top x 2
VACUUM TUBE SO
UND
Stand x 4
VACUUM TUBE SO
UND
UBE S
ACTUU
BM
E STO
D VACU
DUVM
UND OUND
H-EN H-EN
HIG HIG
D
H-EN
HIG
D
H-EN
HIG
VACUUM TUBE SO
UND
D
H-EN
HIG
VACUUM TUBE SO
UND
ID SET
VACUUM TUBE SO
UND
Surround x 2
Subwoofer
Wireless Receiver
Module (SWA-7000)
Front Panel
DISPLAY ICONS
FUNCTION
STOP
OPEN/CLOSE
VOLUME
CONTROL
5V 0.5A
5V 0.5A
5V 0.5A
5V 0.5A
5V 0.5A
PLAY/PAUSE
POWER
VACUUM TUBE AMP
D
H-EN
HIG
VACUUM TUBE SO
UND
5V 0.5A
5V 0.5A
DISPLAY
5V 0.5A
DISC TRAY
REMOTE CONTROL SENSOR
USB
✎✎ Cellular phones or mobile devices placed near the vacuum tube amp or electronic products placed on
the top of the product can cause audio noise or distortion.
✎✎ When the product is on, do not let children touch the product's surface. It will be hot.
✎✎ To upgrade the product's software through the USB jack, you must use a USB flash drive.
6 - English
✎✎ When the product displays a Blu-ray Disc menu, you cannot start the movie by pressing the
button on the product or the remote. To play the movie, you must select Play Movie or Start in the
disc menu, and then press the OK button.
5V 0.5A the home
✎✎ If you are using the Internet or are playing content from a USB device on your TV through
cinema, you cannot select the BD/DVD mode with the SOURCE button. To select the BD/DVD mode,
exit the Internet or stop the content you are playing on the TV, and then select the BD/DVD mode.
Getting Started
Rear Panel
FRONT
R
SUBWOOFER
FRONT
IMPEDANCE : 3Ω
SPEAKERS OUT
L
CENTER
* In case of HT-J7500W
HDMI OUT
HDMI IN
COOLING FAN
AUX IN
* FM ANTENNA
FRONT TOP
FRONT
R
R
SUBWOOFER
FRONT TOP
FRONT
L
LAN
CENTER
SPEAKERS OUT
POWER CORD
L
IMPEDANCE : 3Ω
AUX IN
POWER
HDMI OUT
SPEAKER OUTPUT
CONNECTORS
1
HDMI IN
2
LAN TERMINAL
FM ANT
L
R
OPTICAL
DIGITAL
AUDIO IN
EXTERNAL DIGITAL
AUDIO IN (OPTICAL)
* Connecting the FM Antenna
1. Connect the supplied FM antenna to the FM ANT Jack.
2. Slowly move the antenna wire around until you find a location where reception is good, then fasten
it to a wall or other rigid surface.
✎✎ Maintain a minimum of 10 cm of clear space on all sides of the home cinema to ensure adequate
ventilation. Do not obstruct the cooling fan or ventilation holes.
✎✎ This product does not receive AM broadcasts.
7 - English
Getting Started
Remote Control
Tour of the Remote Control
Press to open and close the disc tray.
Turn the product on and off.
Press to select the Home Cinema's
mode (HDMI, AUX, BD/DVD, etc.).
Adjust the volume.
Cut off the sound temporarily.
Press to skip backwards([) or
forwards(])
or
Press and hold to search
backwards(() or forwards()).
Press to play disc or files.
or
Press to pause playing.
Press to use the Tools menu.
or
To display the number keypad
(may include function keys when
applicable) on the screen, press and
hold the button.
Press to move to the Home screen.
Select on-screen menu items and
change menu values.
,. : Search for active FM stations
and to change channels.
Press to stop the disc playing or to
exist the menu.
Return to the previous menu.
Use to enter the Popup menu/Title
menu.
Press to view the disc menu.
Use to display the playback information
when playing a Blu-ray/DVD disc or files.
Press to apply sound effects.
Press to record FM radio broadcasts.
Press to apply the DTS Neo:Fusion II /
3D sound effect.
These buttons are used both for
menus on the product and also
several Blu-ray Disc functions.
Press to select MANUAL/PRESET in
the Tuner function.
Set a Sleep time to shut off the product.
Select STEREO or MONO for radio
broadcasts.
Use to set a preset radio
frequency.
✎✎ While playing multimedia content in SAMSUNG APPS, press and hold 5 button on the remote to
pause playback. To stop playback, press and hold e (EXIT) button on the remote.
Installing batteries in the Remote Control
1
Use a coin to turn the remote
control cover anti-clockwise to
remove it as shown in the figure
above.
2
3
Insert a 3V lithium battery. Keep
the positive (+) pole upward
when inserting the battery. Put
the battery cover on and align
the '●' marks side by side as
shown in the figure above.
8 - English
Use a coin to turn the cover
clockwise as far as it will go to
fix it in place.
Connections
This section describes various methods of connecting the product to other external components.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Connecting the Speakers
Centre
Product
Front/
Front Top (R)
Surround (R)
Front/
Front Top (L)
Surround (L)
Wireless
Receiver Module
* The Front Top speaker applies to HT-J7750W only.
HT-J7500W :
Front Speakers
Place these speakers in front of your listening position, facing inwards
(about 45°) toward you. Place the front speakers so that their tweeters
will be at the same height as your ear. Align the front face of the front
speakers with the front face of the centre speaker or place them slightly in
front of the centre speakers.
HT-J7750W :
Front/Front Top
Speakers
Place these speakers in front of your listening position, facing inwards
(about 45°) toward you. Place the front speakers so that their tweeters will
be at the same height as your ear. Align the front face of the front/front
top speakers with the front face of the centre speaker or place them
slightly in front of the centre speakers.
HT-J7500W :
Centre Speaker
It is best to install the centre speaker at the same height as the front
speakers. You can also install it directly over or under the TV.
HT-J7750W :
Centre Speaker
It is best to install the centre speaker at the same height as the front/front
top speakers. You can also install it directly over or under the TV.
9 - English
Connections
Subwoofer
Position of the product
Place it on a stand or cabinet
shelf, or under the TV stand.
Selecting the Listening Position
The listening position should be
located about 2.5 to 3 times the
TV's screen size away from the
TV. For example, if you have a 46
inch screen, locate the listening
position 2.92 to 3.50 meters
from the screen.
Connections
Surround Speakers
Place these speakers to the side of your listening position. If there isn't
enough room, place these speakers so they face each other. Position them
about 60 to 90cm above your ear, facing slightly downward.
* Unlike the front and centre speakers, the surround speakers are used
mainly for sound effects. Sound will not come from them all the time.
Subwoofer
The position of the subwoofer is not so critical. Place it anywhere you like.
*Surround speakers must be connected to the wireless receiver module.
*The appearance of your speakers may differ from the illustrations in this manual.
*Each speaker has a coloured label on its back or underside. Each cable has a single coloured band
near its end. Match the band on each cable to the speaker label by colour, and then connect the cable
to the speaker. See page 11 for exact instructions.
Installing the Speakers on the Tallboy Stands
* HT-J7750W only
1. Find the speaker cable that is attached to the Stand.
Turn the Stand and Stand Base upside-down, unravel
the speaker cable, and then draw it through the hole
in the Stand Base.
1
2
✎✎ Handle the Stand carefully. It is heavy.
Stand
2. Connect the Stand Base to the bottom of the Stand.
3. Insert three 5x20 screws into the marked holes
in the Stand Base, and then tighten them with a
screwdriver as shown in the illustration.
3
4
5
6
4. Place the speaker cable into the slot on the bottom
of the stand base.
5. Connect the assembled stand and a speaker together
by matching the labels on the stand and speaker
with each other as shown in the picture.
6. Insert a screw (5x20) into the hole on the rear of the
speaker and tighten by turning it clockwise with a
screwdriver.
7. Repeat steps 1 through 6 with the other speaker and
stand.
10 - English
Speaker
Stand
Stand Base
Speaker Cable Connections
1. Match each speaker cable bundle to the correct speaker by matching the coloured band on each
bundle to the coloured sticker on the bottom or back of each speaker.
2. Connect the speaker wire plugs from each speaker to the back of the product by matching the
coloured band on each cable to the colours of the speaker jacks. When connecting, make sure to
match label colour on the back of speaker.
HT-J7500W
Connections
Front Speaker (R)
Front Speaker (L)
FRONT
Wireless Receiver Module
FRONT
R
SUBWOOFER
IMPEDANCE : 3Ω
SPEAKERS OUT
L
CENTER
R
L
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
Centre Speaker
ID SET
AUX IN
SPEAKERS OUT
FRONT
FRONT
R
SUBWOOFER
IMPEDANCE : 3Ω
Subwoofer
POWER
L
CENTER
LAN
1
HDMI OUT
Surround Speaker (L)
HDMI IN
FM ANT
L
OPTICAL
R
2
DIGITAL
AUDIO IN
Surround Speaker (R)
HT-J7750W
Front Top/
Front Speaker (L)
FRONT TOP
FRONT
Wireless Receiver Module
FRONT TOP
R
FRONT
R
SUBWOOFER
L
L
IMPEDANCE : 3Ω
Front Top/
Front Speaker (R)
CENTER
SPEAKERS OUT
L
R
Centre Speaker
SURROUND SPEAKERS OUT
SPEAKER IMPEDANCE : 3Ω
ID SET
POWER
AUX IN
FRONT TOP
FRONT
R
R
SUBWOOFER
FRONT TOP
FRONT
L
Surround Speaker (R)
11 - English
LAN
CENTER
SPEAKERS OUT
Surround Speaker (L)
L
IMPEDANCE : 3Ω
Subwoofer
HDMI OUT
1
HDMI IN
2
FM ANT
L
R
OPTICAL
DIGITAL
AUDIO IN
Connections
✎✎ If you place a speaker near your TV set, the screen colour may be distorted because of the magnetic
field.
✎✎ Place the wireless receiver module at the rear of the listening position. If the wireless receiver module
is too close to the product, sound from the speakers may be disrupted because of interference.
✎✎ If you use a device such as a microwave oven, wireless LAN Card, Bluetooth device, or any other
device that uses the 2.4/5.8GHz frequencies near the product, sound from the speakers may be
disrupted because of interference.
✎✎ The maximum transmission distance from the product to the wireless receiver module is about 10m,
but may vary depending on your operating environment. If a steel-concrete wall or metallic wall is
between the product and the wireless receiver module, the system may not operate at all, because
the radio waves cannot penetrate metal.
✎✎ If the product doesn't make a wireless connection, you need to run an ID Set between the product
and wireless receiver module. With the product turned off, press and hold (MUTE) button on the
remote control for 5 seconds. Turn on the wireless receiver module. Then, press and hold the "ID
SET" button on the back of the wireless receiver module for 5 seconds, and then turn the product
on.
| CAUTION |
▶▶ If you want to install the speakers on the wall, fasten screws or nails (not provided) firmly to the wall
wherever you want to hang a speaker, and then, using the hole in the rear of each speaker, carefully
hang each speaker on a screw or nail.
▶▶ Do not let children play with or near the speakers. They could get hurt if a speaker falls.
▶▶ When connecting the speaker wires to the speakers, make sure that the polarity (+/­–) is correct.
▶▶ Keep the subwoofer speaker out of reach of children to prevent children from inserting their hands
or alien substances into the duct (hole) of the subwoofer speaker.
▶▶ Do not hang the subwoofer on the wall by the duct (hole).
▶▶ The wireless receiving antenna is built into the wireless receiver module. Keep it away from water
and moisture.
▶▶ For optimal listening performance, make sure that the area around the wireless receiver module
location is clear of any obstructions.
▶▶ In 2-CH mode, you will hear no sound from the wireless surround speakers.
12 - English
Connecting to a TV and External Devices
AUX IN
FRONT TOP
FRONT
R
R
SUBWOOFER
FRONT TOP
FRONT
L
L
IMPEDANCE : 3Ω
AUX IN
POWER
LAN
CENTER
SPEAKERS OUT
HDMI OUT
1
HDMI IN
2
OPTICAL
DIGITAL
AUDIO IN
LAN
HDMI OUT
W
White
1
HDMI IN
Method 1
HDMI IN (ARC)
External
Devices
L
R
2
Method 2
HDMI OUT
OPTICAL
DIGITAL
AUDIO IN
Method 3
AUDIO OUT
OPTICAL OUT
Connecting to a TV
Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the HDMI
IN jack on your TV. If the TV supports ARC, you can hear the audio from your TV through the home cinema
with only this cable connected. See page 19 in this manual and the section on ARC in your TV's user's
manual for details.
Connecting to External Devices
Method 1 HDMI IN : Connecting to an External Component with an HDMI Cable
Connect an HDMI cable (not supplied) from the HDMI IN jack on the back of the product to the HDMI
OUT jack on your digital device.  Select the HDMI1 or HDMI2 mode.
Method 2 AUX IN : Connecting an External Analogue Component
Using an RCA audio cable (not supplied), connect the AUDIO In jack on the product to the AUDIO Out
jack on the external analogue component.  Select the AUX mode.
●● Be sure to match the colours on the cable plugs to the colours on the input and output jacks.
Method 3 OPTICAL : Connecting an External Digital Audio Component
Use to connect the digital audio output of digital signal components such as Cable Boxes and Satellite
Receivers (Set-Top-Boxes) to the home cinema. Using a digital optical cable (not supplied), connect the
Optical Digital Audio In jack on the product to the Digital Optical Out jack of the external digital device
using a digital optical cable.  Select the D. IN mode.
✎✎ To see video from your Cable Box/Satellite receiver, you must connect its video output directly to your TV.
✎✎ This system supports Digital sampling frequencies of 32 kHz or higher from external digital
components.
✎✎ This system supports only DTS and Dolby Digital audio. MPEG audio, a bitstream format, is not supported.
Selecting an External Device to Use
To select an external device after you have connected it, press the SOURCE button. Each time you press
the button, the mode changes in this order : BD/DVD ; D. IN ; AUX ; HDMI1 ; HDMI2 ; FM ; BT
13 - English
Connections
R
Red
FM ANT
FM ANT
L
R
Connections
Connecting to a Network Router
Wireless Network
You can connect your product to your network
router using one of the methods illustrated
below.
Wired Network
FRONT TOP
FRONT
R
R
SUBWOOFER
FRONT TOP
FRONT
L
L
IMPEDANCE : 3Ω
AUX IN
POWER
LAN
CENTER
SPEAKERS OUT
HDMI OUT
1
HDMI IN
2
FM ANT
L
R
OPTICAL
Wireless IP sharer
DIGITAL
AUDIO IN
Broadband modem
(with integrated router)
Broadband
service
Broadband
service
Or
✎✎ If your wireless IP router supports DHCP, this
Router
Broadband
service
Broadband
modem
product can use a DHCP or static IP address to
connect to the wireless network.
✎✎ Set your wireless IP router to Infrastructure
mode. Ad-hoc mode is not supported.
✎✎ The product supports only the following
wireless security key protocols:
-- WEP (OPEN/SHARED), WPA-PSK (TKIP/
AES), WPA2-PSK (TKIP/AES)
✎✎ Select a channel on the wireless IP router that
✎✎ Your router or your Internet Service Provider's
policies may prevent the product from
accessing Samsung's software update server.
If this occurs, contact your Internet Service
Provider (ISP) for more information.
✎✎ DSL users, please use a router to make a
network connection.
✎
✎ Try to use the CAT 7 cable to connect.
✎✎ You cannot use the product if the network
speed is slower than 10Mbps.
✎✎ To use the DLNA function, you must connect
your PC to your network as shown in the
illustrations above.
The connection can be wired or wireless.
is not currently being used. If the channel set
for the wireless IP router is currently being
used by another device nearby, it will result in
interference and communication failure.
✎✎ In compliance with the newest Wi-Fi
certification specifications, Samsung home
cinemas do not support WEP, TKIP, or TKIPAES (WPS2 Mixed) security encryption in
networks running in the 802.11n mode.
✎✎ Wireless LAN, by its nature, may cause
interference, depending on the operating
conditions (AP performance, distance,
obstacles, interference by other radio devices,
etc.).
14 - English
Settings
The Initial Settings Procedure
●●
●●
●●
1 PLAY DISC
The Home menu will not appear if you do
not configure the initial settings.
The OSD (On Screen Display) may change in
this product after you upgrade the software
version.
The access steps may differ depending on
the menu you selected.
Displays information about the disc currently in
the disc tray. Press OK to start playing the disc.
2 MULTIMEDIA
Play photos, videos, or music content from
Discs, USB devices, PCs, mobile devices.
3 SAMSUNG APPS
After you have finished connecting the home
cinema to your TV, turn on the TV, and then turn
on the home cinema. The first initial setup screen
appears. The setup screens appear in this order:
Language, Network Configuration, Terms and
Conditions, Screen Resolution (Aspect Ratio),
and Speaker Layout (HT-J7500W only). Follow
the instructions displayed on each screen, which
will guide you through the easy setup procedure.
When the initial setup is completed, a tutorial
screen guiding the Home menu will appear. To
exit this screen, press the e (EXIT) button on the
remote.
Download/Access various for pay or free-ofcharge applications.
✎✎ To edit your settings after the initial setup,
Set up the wireless mirroring function between
the home cinema and a smart phone or tablet.
1
PLAY DISC
A list of useful and popular apps we
recommend you download.
5 MY APPS
Displays downloaded and installed apps. You
can change the display order. (See page 44)
6 Screen Mirroring
✎✎ Depending on your country, this menu
function may not be supported.
7 Source
The Home Screen at a Glance
2
3
MULTIMEDIA
SAMSUNG APPS
Select the desired source such as Digital In,
AUX, HDMI IN 1, HDMI IN 2, Tuner (FM Radio)
or Bluetooth depending on what external
device is connected and its status. You can also
use the remote's SOURCE button or the main
unit's
button.
8 Settings
Set various functions
to suit your personal
5V 0.5A
preferences.
No Disc
RECOMMENDED
App 1
App 2
4
MY APPS
App 3
App 4
App 5
5
App 6
Screen Mirroring
6
Source
Settings
7
8
Settings
select Settings > System > Setup in the Home
screen or select the Reset option. (See page
21)
4 RECOMMENDED
15 - English
D
H-EN
HIG
VACUUM TUBE SO
UND
Settings
■■
Selecting an Option on the Home Screen
1. To select an option on the Home screen,
move the cursor using the 78:; buttons
until it highlights the option of your choice,
and then press the OK button.
3
OK / DIRECTION Button :
Press 78:; to move the cursor or
select an item.
●● Press the OK button to activate the
currently selected item or confirm a
setting.
4
e (EXIT) Button : Press to exit the
current menu.
●●
✎✎ If you leave the product in the stop mode for
more than 5 minutes without using it, a screen
saver appear on your TV. If the product is left
in the screen saver mode for more than 20
minutes, the power will automatically turn off.
Detailed Function Information
Accessing the Settings Screen
1. Select Settings on the Home screen, and
then press OK. The Settings screen appears.
Settings
Picture
Picture
Sound
Network
Smart Hub
System
Support
UHD Output
Auto
3D Settings
TV Aspect Ratio
16:9 Original
BD Wise
Off
Resolution
Auto
Movie Frame (24 fps)
Auto
DVD 24 fps Conversion
Off
Each Settings function, menu item, and individual
option is explained in detail on-screen. To view
an explanation, use the 78:; buttons to
select the function, menu item, or option. The
explanation will usually appear on the right of the
screen.
A short description of each Settings function
starts below. Additional information on some
of the functions is also in the Appendix of this
manual.
Settings Menu Functions
Picture
UHD Output
2. To access the menus, sub-menus, and
options on the Settings screen, please refer
to the remote control illustration below.
This option outputs HDMI video at UHD (Ultra
High Definition) resolution. This is only available
when Movie Frame is set to Auto.
Buttons on the Remote Control Used
for the Settings Menu
✎✎ To use this feature, you must connect the
3D Settings
1
3
2
product to a device that supports UHD
resolution and you must have content that
plays at 24 fps (film speed).
4
1
HOME Button : Press to move to the
Home screen.
2
' (RETURN) Button : Press to return to
the previous menu.
Set up the 3D related functions.
3D Blu-ray Playback Mode: Select whether
to play a Blu-ray Disc with 3D contents in 3D
Mode. If you move to the Home or Smart Hub
Home menu while in 3D mode, the product will
switch to 2D automatically.
Screen Size: Enter the size of the TV attached
to the product. The product will automatically
adjust the 3D output to the screen size of the
TV.
✎✎ Carefully read the health and safety
information before viewing 3D content. (See
page 3)
16 - English
TV Aspect Ratio
HDMI Deep Colour
Lets you adjust the output of the product to
the screen size of your TV. (See page 51)
Lets you set the product to output video
from the HDMI OUT jack with Deep Colour.
Deep Colour provides more accurate colour
reproduction with greater colour depth.
BD Wise
BD Wise is Samsung’s latest inter-connectivity
feature. When you connect a Samsung product
and a Samsung TV with BD Wise to each
other via HDMI, and BD Wise is on in both the
product and TV, the product outputs video at
the video resolution and frame rate of the Bluray/DVD Disc.
Progressive Mode
Lets you improve picture quality when viewing
DVDs.
Sound
Lets you set the output resolution of the HDMI
video signal to BD Wise, Auto, 1080p, 1080i,
720p, 576p/480p. The number indicates the
number of lines of video per frame. The i and
p indicate interlaced and progressive scan,
respectively.
The more lines, the higher quality.
Movie Frame (24 fps)
Setting the Movie Frame (24 fps) feature to
Auto lets the product adjust its HDMI output
to 24 frames per second automatically for
improved picture quality if attached to a 24 fps
compatible TV.
●● You can enjoy the Movie Frame (24 fps)
feature only on a TV supporting this frame
rate.
●● Movie Frame is only available when the
product is in the HDMI 1080p output
resolution modes.
DVD 24 fps Conversion
Converts DVD playback to 24 frames per
second and outputs it via HDMI. This option is
only available when Movie Frame (24 fps) is set
to Auto.
✎✎ This feature applies to NTSC discs only.
Fit Screen Size
Lets you select the optimal size for the Smart
Hub or Screen Mirroring Screen.
HDMI Colour Format
Lets you configure the settings of the speakers
you have connected to obtain the best possible
surround sound.
Normal Mode : Select if you have set up your
speakers in the recommended speaker layout
with the surround speakers next to or behind
the listening positions.
Simple Mode : Select if you have put your
surround speakers in front of the listening
position. Downmixes the front sound to the
surround sound speakers.
✎✎ SFE, Virtual 7.1 will not operate when the
Simple Mode is on.
Speaker Settings
Sound Output : Lets you select which speakers
are active, either the TV's speakers or the home
cinema's speakers.
Settings (Home theatre speakers) : Lets you
adjust the following speaker settings and turn
the test tone on and off so you can test the
speakers.
-- Volume Level : Lets you adjust the relative
loudness of each speaker from 6dB to
-6dB. For example, if you like deep bass,
you can increase the loudness of the
subwoofer by 6dB.
-- Distance : Lets you adjust the relative
distance of each speaker from the listening
position up to 9 meters. The farther the
distance, the louder the speaker will be.
-- Speaker Test : Begins a test to set the best
surround sound configuration. Press Stop
Test to stop the test while it is in progress.
Lets you set the colour space format for the
HDMI output to match the capabilities of the
connected device (TV, monitor, etc).
17 - English
Settings
Simple Speaker Setup (HT-J7500W only)
Resolution
Settings
✎✎ Speaker Test Order
HT-J7500W : Front Left ; Front Right ;
Centre ; Surround Left ; Surround Right
; Subwoofer
HT-J7750W : Front Left ; Front Right ;
Centre ; Surround Left ; Surround Right
; Front Top Left ; Front Top Right ;
Subwoofer
Speaker Settings (Multiroom Link) : You can
enjoy sound through a remote speaker that is
connected to the home cinema through your
home network. To use the network speaker,
select Multiroom. If there is a network speaker
available, it will appear on the screen.
-- Don't Use : The network speaker is not
used.
-- Multiroom : The network speaker outputs
audio. All network speakers output the
same audio regardless of channel using the
PCM format only.
✎✎ SOUND EFFECT and 3D SOUND are not
applied if Multiroom is set to on.
✎✎ The network speaker is not available when
Screen Mirroring is active.
✎✎ For further details, refer to the Multiroom
Link manual from the web site.
www.samsung.com > Support > Search
for the product name > Multiroom Link >
Download PDF
Sound Customiser
Sound Customiser lets you calibrate the home
cinema for the optimal sound quality based on
your hearing level and the ambient conditions.
To create a Custom Sound Profile, follow these
steps:
1. In the Sound Customiser Menu, select Add
Custom Sound.
2. On the next screen, select Start. The
Preview screen appears.
3. Select Preview to preview the Test
Sound. Select Next, and then press OK to
continue.
4. A 6-step test will start. During each stage,
the TV will sound a test tone at a different
frequency. The tone will begin softly and
increase in volume. Select Yes when you
can hear the test tone. If you want to
listen to it again, select Retry. Each time
you select Yes, the TV will move on to the
next tone. Once the test is complete, a
screen appears that lets you compare the
original sound to the calibrated sound.
5. Select Next, and then press the OK button
to continue. The on-screen keyboard
appears with a default profile name.
6. Enter a name for the calibrated sound
profile or accept the default name, select
Done, and then press the OK button.
7. Select Done on the next screen, and
then press the OK button. The Sound
Customiser screen reappears.
Custom Sound Profile : Select a Sound Profile
you created to activate it. Or select Hearing
Impaired, a Custom Sound Profile especially
composed of large sounds for those with
hearing disorders.
✎✎ If there are more than 3 Custom Sounds
registered, Family mode will be activated
which is composed of the average value of
all registered profiles.
Add Custom Sound : Create and add a new
Custom Sound Profile. See the instructions
above.
Edit Custom Sound : Choose a Custom Sound
Profile to modify it. Follow the same steps
you used when creating a sound profile. This
function is only available if you have added
a Custom Sound Profile using Add Custom
Sound. (See above.)
Manage Custom Sound : Rename or delete
Custom Sound Profiles. This function is only
available if you have added a Custom Sound
Profile using Add Custom Sound. To select a
profile, highlight the check box to the right of
the profile, and then select Rename or Delete.
Equaliser
Lets you configure the Equaliser settings
manually.
18 - English
Smart Volume
Audio Sync
Lets you set the product so that the volume
remains stable when a scene change occurs or
when you change the channel.
When the product is attached to a digital TV,
lets you adjust the audio delay so that the
audio syncs with the video. You can set the
delay between 0 and 300 milliseconds.
Audio Return Channel
✎✎ The Auto function in Audio Sync is
Digital Output
Lets you set the Digital Output to match the
capabilities of the AV receiver you’ve connected
to the product. For more details, please refer
to the digital output selection table. (See page
57)
Dynamic Range Control
Lets you apply dynamic range control to Dolby
Digital, Dolby Digital Plus, and Dolby TrueHD
audio.
Auto: Automatically controls the dynamic range
of Dolby TrueHD audio, based on information
in the Dolby TrueHD soundtrack. Also turns
dynamic range control off for Dolby Digital and
Dolby Digital Plus.
Off: Leaves the dynamic range uncompressed,
letting you hear the original sound.
On: Turns dynamic range control on for all three
Dolby formats. Quieter sounds are made louder
and the volume of loud sounds is reduced.
Downmixing Mode
Lets you select the multi-channel downmix
method that is compatible with your stereo
system. You can choose to have the product
downmix to Normal Stereo or to Surround
Compatible.
guaranteed to work only with a Samsung
TV that supports the ARC function (the
Anynet+ function).
Network
Network Status
Lets you check the current network and
Internet status.
Network Settings
Lets you configure the network connection so
you can enjoy various features such as Internet
services or DLNA Wi-Fi functionality, and
perform software upgrades.
Wi-Fi Direct
Lets you connect a Wi-Fi Direct device to the
product using a peer-to-peer network, without
the need for a wireless router. Note that if the
product is connected to a wireless network,
it may be disconnected when you use Wi-Fi
Direct. (See page 25)
✎✎ Text files, such as files with a .TXT or .DOC
extension, will not display when you are using
the Wi-Fi Direct function.
Multimedia Device Settings
Allow other devices on your network, such as
smart phones and tablets, to share content with
your product.
Device Name
Lets you assign an identifying name to the
product. You use this name to identify the
product when you are connecting external WiFi devices (smart phones, tablets, etc.) to it.
19 - English
Settings
Lets you direct the sound from the TV to the
Home Cinema speakers. Requires an HDMI
connection and an Audio Return Channel (ARC)
compatible TV.
●● If Audio Return Channel is set to On and
you are using an HDMI cable to connect
the product to the TV, digital optical input is
disabled.
●● If Audio Return Channel is set to Auto and
you are using an HDMI cable to connect
the product to the TV, ARC or digital optical
input is selected automatically.
Settings
BD-Live Settings
System
Lets you set various BD-Live functions. BD-Live
allows you to access extra features available on
some Blu-ray Discs if you are connected to the
Internet.
BD-Live Internet Connection : Lets you fully
allow, partly allow, or prohibit a BD-Live
Internet connection.
BD Data Management : Manage BD data
downloaded from a BD-Live service or Blu-ray
Disc.
✎✎ To use BD-Live, you must insert a USB
storage device into the home cinema's USB
port.
Smart Hub
Caption
Use to modify captions on VOD playback that
supports closed captions. Lets you change
displayed caption's font colour and size.
✎✎ The Caption function does not work with
VOD services that don't support closed
captions. For some VOD services that do
support closed captions, the functions
settings may not be applied.
✎✎ Depending on your country, this menu
function may not be supported.
Lets you re-run the Initial Settings procedure.
Refer to the descriptions displayed on the screen.
Quick start
Lets you set the product to turn on quickly by
decreasing the boot time.
✎✎ If this function is set to On, Standby power
consumption will increase. (About 12W ~
20W)
Language
Lets you select the language you prefer for the
on-screen menu, disc menu, audio, subtitles, etc.
●● The language you select for the disc menu,
disc audio, or subtitles will only appear if it is
supported on the disc.
Device Manager
Lets you connect a wireless USB keyboard or
mouse to the USB port on the front of the
product.
Keyboard Settings: Lets you configure a
wireless USB keyboard connected to the
product.
✎✎ You can use the keyboard only when a
QWERTY keyboard screen or window
appears in the Web Browser.
Terms & Policy
Samsung account Terms and Conditions,
Privacy Policy
You can view the terms of use and privacy
policy for Smart Hub, Samsung accounts, and
various other services.
Mouse Settings: Lets you configure a wireless
USB mouse connected to the product. You
can use the mouse in the product's menu in
the same way you use a mouse on your PC.
■■ To use a mouse with the product's menu:
1. Connect the USB mouse to the product.
Reset Smart Hub
Resets all Smart Hub settings to their default
settings. To use, you must enter the security
PIN. Press and hold the 123 button until the Num
pad appears on the screen. When the Num pad
appears, select a number using the 78:;
button and then press the OK button.
✎✎ The default security PIN is 0000.
Setup
2. Click the primary button you selected
in Mouse Settings. The Simple Menu
appears.
3. Click the menu options you want.
✎✎ Some USB HID keyboards and mice may not
be compatible with your product.
✎✎ Some HID keyboard keys may not work.
✎✎ Wired USB keyboards are not supported.
✎✎ Some applications may not be supported.
20 - English
✎✎ If a wireless HID Keyboard does not operate
because of interference, move the keyboard
closer to the product.
Security
1. Remove any disc or USB storage device.
2. Press and hold the @ button on the front
panel for 5 seconds or more.
All settings will revert to the factory
default settings.
✎✎ When the factory default settings are
restored, all the user stored BD data is
deleted.
1)Connect the product to an Anynet+
(HDMI-CEC)-compliant Samsung TV using
HDMI Cable.
2)Set the Anynet+ (HDMI-CEC) feature to
On in both the TV and the product.
3)Search for and then select the product
in the TV's Anynet+ (HDMI-CEC) list. For
more exact instructions, see the Anynet+
section of the TV's user's manual.
DivX® Video On Demand
View DivX® VOD Registration Codes to
purchase and play DivX® VOD contents.
Support
Remote Management
When activated, lets Samsung Call Centre
agents diagnose and fix problems with the
product remotely. Requires an active Internet
connection. Remote Management service
might not be available in some countries.
Software Update
For more information about the Software
Update function, see "Upgrading Software" on
page 26.
Usage Mode
General
Lets you specify the display brightness and time
zone.
Front Display: Lets you change the brightness
of the front panel.
Time Zone: You can specify the time zone
that is applicable to your area.
Menu Transparency: Lets you adjust the
transparency of the menu box.
Lets you set the Usage Mode. If you are using
the home cinema at home, always select Home
Use. Store Demo is for retail display settings
only.
Contact Samsung
Provides contact information for assistance
with your product.
Reset
Anynet+ (HDMI-CEC)
Anynet+ is a convenient function that offers
linked operations with other Samsung products
that have the Anynet+ feature, and lets you
control those products with one Samsung TV
remote. To operate this function, you must
connect this product to an Anynet+ Samsung
TV using an HDMI cable.
Reverts all settings to their defaults except for
the network and Smart Hub settings. Requires
that you enter your security PIN. Press and hold
the 123 button until the Num pad appears on
the screen. When the Num pad appears, select
a number using the 78:; button and then
press the OK button. The default security PIN is
0000.
21 - English
Settings
Press and hold the 123 button until the Num
pad appears on the screen. When the Num pad
appears, select a number using the 78:;
button and then press the OK button. The
default security PIN is 0000. Enter the default
PIN to access the security function if you
haven't created your own PIN.
BD Parental Rating: Prevents playback of
Blu-ray Discs with a rating equal to or above
a specific age rating you have set unless you
enter the PIN.
DVD Parental Rating: Prevents playback of
DVDs with a rating above a specific numerical
rating you have set unless you enter the PIN.
Change PIN: Lets you change the 4-digit PIN
used to access security functions.
■■ If you forget your PIN
To use an Anynet+ (HDMI-CEC) function,
follow the instructions below.
Settings
Radio Setup
●●
●●
To listen to the radio, you must connect the
supplied FM antenna.
To tune to a preset station, press the
PRESET button to select PRESET, and then
press the 78 buttons to select the preset
station.
Recording FM Radio
You can record your favorite radio broadcast on a
inserted USB storage device.
Operating the Radio with the Remote
Control
1. Press the SOURCE button to select FM.
2. Tune to the desired station.
●● Preset Tuning 1 : Press the PRESET button
to select PRESET, and then press the 78
buttons to select a preset station.
-- Before you can tune to preset stations,
you must add preset stations to the
product's memory.
●● Manual Tuning : Press the PRESET button
to select MANUAL, and then press the
78 buttons to tune to a lower or higher
frequency.
●● Automatic Tuning : Press the PRESET
button to select MANUAL, and then press
and hold the 78 buttons to automatically
search the band.
Selecting Mono or Stereo
Press the ST/MO button.
●● Each time you press the button, the sound
switches between STEREO and MONO.
●● In a poor reception area, select MONO for a
clear, interference-free broadcast.
Presetting Stations
Example : Presetting FM 89.10 into memory.
1. Press the SOURCE button to select FM.
2. Press the 78 buttons to select <89.10>.
3. Press the MEMORY button.
●● NUMBER flashes on the display.
4. Press the MEMORY button again.
●● Press the MEMORY button before
NUMBER disappears from the display on its
own.
●● After you press the MEMORY button,
NUMBER disappears from the display and
the station is stored in memory.
5. To preset another station, repeat steps 2 to 4.
1. Insert a USB device into the USB jack on the
front of the product.
2. Press the SOURCE button to select FM, and
then then press the 78 buttons to select
the station you want to record.
3. Press the A (Red) button to start recording
the radio broadcast. Recording begins.
●● The recorded time is displayed on the left
and the recording time still available, based
on the amount of free space in the USB
storage device, is displayed on the right.
D
H-EN
HIG
D
H-EN
HIG
VACUUM TUBE SO
UND
VACUUM TUBE SO
UND
4. Press the e (EXIT) button to finish your
recording. The recording is stopped and
saved as an .mp3 file at the same time. To
play the recorded file, refer to "Playing Files
on a Storage Device".
✎✎ The recorded file is saved in the Tuner folder
which is created automatically.
(OPEN/CLOSE), (POWER), e
(EXIT), (MUTE), and VOL +/ -, buttons are
operable while FM radio is being recorded.
✎✎ If you don't press any buttons while recording,
the screen saver will be enabled.
✎✎ Sound effects, such as DSP, EQ, etc., are not
recorded during FM radio recording.
✎
✎ The radio is recorded at a set, default volume
even if you change the volume or press the
(MUTE) button during the recording process.
✎✎ If you remove the USB device or Power Cable
during the recording process, the portion of
the file which has already been recorded may
not play back.
✎✎ Recording will not start if the remaining free
space in the USB storage device is less than
2MB.
✎✎ If the USB device is removed or has insufficient
space (under 2MB), the appropriate message
is displayed and the recording stops.
✎✎ Only the
5V 0.5A
5V 0.5A
22 - English
Network Setup
ĞĞ
When you connect this product to a network,
you can use network based applications and
functions such as Smart Hub and BD-LIVE, and
upgrade the product's software through the
network connection. For more information about
accessing and using Internet services, see the
Network Services chapter of this manual on pages
43~50. Instructions for configuring the
network connection start below.
Configuring Your Network Connection
1. In the Home screen, select Settings, and then
press the OK button.
1. In the Network Settings screen, change
Network type to Wired. Then, select Connect
and press the OK button.
The product searches for a network, and
then displays the connection failed message.
✎✎ If it is possible to connect the home cinema
to your network wirelessly, select Change
Network at this point, change the Network
type to Wireless, and then go to the
instructions for wireless networks on the next
page.
Network Settings
Wired network connection failed.
MAC Address
IP Address
Subnet Mask
Gateway
DNS Server
XX:XX:XX:XX:XX:XX
0. 0. 0. 0
0. 0. 0. 0
0. 0. 0. 0
0. 0. 0. 0
Unable to connect to the network. Try the following: check if your IP address is set
correctly in IP Settings. Contact your Internet service provider for more information.
Change Network
IP Settings
Retry
Close
2. Select Network, and then press the OK
button.
2. Use the :; buttons to select IP Settings,
and then press the OK button. The IP Settings
screen appears.
3. Select Network Settings, and then press the
OK button.
3. Select the IP setting field, and then set it to
Enter manually.
4. Go to the instructions for Wired networks
starting or the instructions for Wireless
networks starting on the next page.
4. Select a parameter to enter (IP Address, for
example), and then press OK. Use the 78
buttons on the remote control to enter the
numbers for the parameter. Or use the Num
keypad to enter a parameter number. Press and
hold the 123 button until the Num pad appears
on the screen. When the Num pad appears,
select a number using the 78:; button
and then press the OK button. Use the :;
buttons on the remote control to move from
entry field to entry field within a parameter.
When done with one parameter, press the
OK button.
Wired Network
ĞĞ
Wired – Automatic
After following Steps 1 to 3 above:
1. In the Network Settings screen, change
Network type to Wired. Then, select Connect
and press the OK button. The product
detects the wired connection, verifies the
network connection, and then connects to
the network.
2. When it is done, highlight OK, and then
press OK button.
5. Press the 7 or 8 button to move to another
parameter, and then enter the numbers for
that parameter following the instructions in
Step 4.
23 - English
Settings
If you didn't configure your network connection
during the initial settings procedure or you need
to reset the network connection, follow the
directions below.
Before you begin, contact your Internet Service
Provider to find out if your IP address is static or
dynamic. If it is dynamic, and you have a wired
or wireless network, we recommend using the
Automatic configuration procedures described
below.
If you are connecting to a wired network, connect
the product to your router using a LAN cable
before you start the configuration procedure.
To begin configuring your network connection,
follow these steps:
Wired - Manual
If you have a static IP address or the automatic
procedure does not work, you'll need to set the
Network Settings values manually.
After following Steps 1 to 3 above:
Settings
6. Repeat Steps 4 and 5 until you have filled in
all parameters.
✎✎ You can get the network parameter values
from your Internet provider.
7. When finished entering all the parameter
values, select OK, and then press the OK
button. The home cinema verifies the
network connection and then connects to
the network.
Wireless Network
You can set up a wireless network connection in
three ways:
-- Wireless Automatic
-- Wireless Manual
-- WPS(PBC)
Before you configure the wireless network
connection, disconnect any wireless network
devices currently connected to the product
or, if applicable, the product's current wired
connection.
ĞĞ
Wireless - Automatic
After following Steps 1 to 3 in "Configuring Your
Network Connection" on page 23:
1. In the Network Settings screen, change
Network type to Wireless. The product
searches for and then displays a list of the
available networks.
Network Settings
Select your network type.
Network type
4. When finished, select Done, and then press
the OK button. The product verifies the
network connection and then connects to
the network.
✎✎ You should be able to find the security code or
pass phrase on one of the set up screens you
used to set up your router or modem.
ĞĞ
Wireless - Manual
If you have a static IP address or the Automatic
procedure does not work, you'll need to set the
Network Settings values manually.
After following Steps 1 to 3 in "Configuring Your
Network Connection" on page 23:
1. In the Network Settings screen, change
Network type to Wireless. The product
searches for and then displays a list of the
available networks.
2. Scroll through the list, select the desired
network or Add Network, and then press the
OK button.
3. If you selected a network in Step 2, go to
Step 6.
If you selected Add Network, go to Step 4.
4. Enter your wireless network or wireless
router's name.
●● Enter letters by selecting a letter with the
78:; buttons, and then pressing the
OK button.
●● To display capital letters (or redisplay lower
case letters if capital letters are displayed),
select
, and then press the OK button.
To display symbols and punctuation, select
123#&, and then press the OK button. To
redisplay letters, select 123#&, and then
press the OK button.
When finished, select Done, and then press
the OK button.
●●
Wireless
Wireless network
si-ap
You can connect your Bluray player to the internet.
Please select which wireless
network to use.
iptime
KIMING_VTOWER
Refresh
WPS(PBC)
2. Select the desired network, and then press
the OK button.
3. On the Security screen, enter your network's
security code or pass phrase.
Enter letters by selecting a letter with
78:; buttons, and then pressing OK
button.
5. On the Security type screen that appears,
use the ,. buttons to select the network's
Security type, and then press the OK button.
On the next screen, enter your network's
security code or pass phrase.
●● Enter letters by selecting a letter with the
78:; buttons, and then pressing the
OK button.
When finished, select Done, and then press
the OK button. The product searches for the
network.
24 - English
✎✎ You can get the Network parameter values
from your Internet provider.
11. When finished, select OK, and then press the
OK button. The Security screen appears.
12. On the Security screen, enter your network's
security code or pass phrase. Enter letters by
selecting a letter with the 78:; buttons,
and then pressing the OK button.
13. When finished, select Done at the right of
the screen, and then press the OK button.
The product verifies the network connection
and then connects to the network.
14. After the home cinema verifies the network,
select OK, and then press the OK button.
✎✎ You can also begin the Manual Network setup
by going to Settings > Network > Network
Status.
ĞĞ
WPS(PBC)
One of the easiest ways to set up the wireless
network connection is using the WPS(PBC)
function. If your wireless router has a WPS(PBC)
button, follow these steps:
After following Steps 1 to 3 in "Configuring Your
Network Connection" on page 23:
1. In the Network Settings screen, change
Network type to Wireless. The product
searches for and then displays a list of the
available networks.
2. Scroll the list down, select WPS(PBC), and
then press the OK button.
3. Press the WPS(PBC) button on your
router within two minutes. Your product
automatically acquires all the network
settings values it needs and connects to your
network after the network connection is
verified.
4. When it is done, highlight OK, and then
press the OK button.
✎✎ For a WPS connection, set your wireless
router’s security encryption to AES. WEP
security encryption does not support a WPS
connection.
Wi-Fi Direct
The Wi-Fi Direct function allows you to connect
Wi-Fi Direct devices to the product and each other
using a peer-to-peer network, without a wireless
router.
✎✎ Some Wi-Fi Direct devices may not support
the DLNA function if connected via Wi-Fi
Direct. If this is the case, change the network
connection method you used to connect the
device to the home cinema.
✎
✎ Wi-Fi Direct transmissions can interfere
with Bluetooth signals. Before you use the
Bluetooth function, we strongly recommend
that you turn off the Wi-Fi Direct function on
any device in which it is currently on.
1. Turn on the Wi-Fi Direct device and activate
its Wi-Fi Direct function.
2. In the Home screen, select Settings, and then
press the OK button.
3. Select Network, and then press the OK
button.
4. Select Wi-Fi Direct, and then press the OK
button.
The Wi-Fi Direct devices that you can connect
the home cinema to appear.
25 - English
Settings
6. The Network connection fail screen appears.
Use:; buttons to select IP Settings, and
then press the OK button.
7. Select the IP setting field, and then set it to
Enter manually.
8. Select a network parameter to enter (IP
Address, for example), and then press
OK button. Use the 78 buttons on the
remote control to enter the numbers for
the parameter. Or use the Num keypad to
enter a parameter number. Press and hold the
123 button until the Num pad appears on the
screen. When the Num pad appears, select a
number using the 78:; button and then
press the OK button. Use the :; buttons on
the remote control to move from entry field
to entry field within a parameter. When done
with one value, press the OK button.
9. Press the , or . button to move to another
parameter, and then enter the numbers for
that parameter following the instructions in
Step 8.
10. Repeat Steps 8 and 9 until you have filled in
all parameters.
Settings
2. The PIN pop-up appears.
3. Note the PIN code in the pop-up, and then
enter it into the appropriate field in the Wi-Fi
Direct device you want to connect.
4. The Connecting pop-up appears, followed by
the Connected pop-up. When it closes, you
should see the device listed as connected on
the Wi-Fi Direct screen.
Settings
Wi-Fi Direct
Device Name : [HTS]J7500W
Select your Wi-Fi Direct device to connect to.
AndroidXXXXXXX
Disconnected
Refresh
Close
✎✎ The current wired or wireless network
5. You have three ways to complete the Wi-Fi
connection:
●● Through the Wi-Fi device.
●● Through the product using PBC.
●● Through the product using a PIN.
Each is covered below.
Through the Wi-Fi Device
1. On the Wi-Fi device, follow the device's
procedure for connecting to another Wi-Fi
Direct device. See the device's user manual
for instructions.
2. When you have completed the procedure,
you should see a pop-up on your TV screen
saying that a device that supports Wi-Fi
Direct has requested to connect. Select OK,
and then press the OK button to accept.
3. The Connecting pop-up appears, followed by
the Connected pop-up. When it closes, you
should see the device listed as connected on
the Wi-Fi Direct screen.
●●
The PBC and PIN procedures connect devices
automatically.
Through the Product Using PBC
connection will be disconnected when you use
the Wi-Fi Direct function.
✎
✎ Text files, such as files with a .TXT or .DOC
extension, will not display when you are using
the Wi-Fi Direct function.
Upgrading Software
The Software Update menu allows you to
upgrade the product’s software for performance
improvements or additional services.
●●
Never turn the product off or back on
manually during the update process.
1. In the Home menu, select Settings, and then
press the OK button.
2. Select Support, and then press the OK
button.
3. Select Software Update, and then press the
OK button.
4. To download update software and update
now, select Update now, and then press the
OK button. See "Update now" on the next
page for details.
5. To let the product download update software
automatically when available, select Auto
update, and then press the OK button. (See
page 27)
1. Select the Wi-Fi Direct device you want to
connect to this product, and then press the
OK button.
✎✎ The upgrade is complete when the product
2. The Connecting pop-up appears, followed by
the Connected pop-up. When it closes, you
should see the device listed as connected on
the Wi-Fi Direct screen.
responsibility for product malfunction
caused by an unstable Internet connection
or consumer negligence during a software
upgrade.
✎✎ If you want to cancel the upgrade while the
upgrade software is downloading, press the
OK button.
✎✎ When a system upgrade is in progress,
"UPDATE" is displayed on the front panel.
Through the Product Using a PIN
1. Select the Wi-Fi Direct device you want to
connect to this product, and then press the
OK button.
turns off, and then turns on again by itself.
✎✎ Samsung Electronics takes no legal
26 - English
Update now
Update by USB
You can use Update now to update the software
through your network connection or by using
a USB flash drive. The network instructions are
below. The USB flash drive instructions are on this
page.
1. Visit www.samsung.com.
✎✎ When the system upgrade is done, check the
software details in the Product Information
section of the Contact Samsung screen.
✎✎ Do not turn off the product during the
Software Upgrade. It may cause the product
to malfunction.
3. On the next screen, enter the product's
model number into the search field. As
you enter the model number, a drop down
will display products that match the model
number.
4. Left click your product's model number in the
drop down list.
5. On the page that appears, select Downloads.
6. Find the Upgrade File (USB type) in the
Description column. Click the ZIP icon in the
Download File column on the right.
7. Click Send in the pop-up that appears. The
file downloads to your PC.
8. Unzip the zip archive to your computer. You
should have a single folder with the same
name as the zip file.
9. Copy the folder to a USB flash drive.
10. Make sure no disc is inserted in the product,
and then insert the USB flash drive into the
USB port of the product.
11. In the product’s menu, go to Settings >
Support > Software Update.
Auto update
12. Select Update now.
You can set the Auto update function so that the
product downloads new upgrade software when
it is in Auto update mode.
In Auto update mode, the product is on, but
its Internet connection is active. This allows
the product to download upgrade software
automatically, when you are not using it.
13. The product searches for the software on the
USB drive. When it finds the software, the
Update Request pop-up appears.
1. Press the 78 buttons to select Auto update
mode, and then press the OK button.
2. Select On or Off.
If you select On, the product will
automatically download new upgrade
software when it is in Auto update mode
with the power on. If it downloads new
upgrade software, the product will ask you
if you want to install it when you turn the
product on.
14. Select OK. The product upgrades the
software, turns off, and then turns on
automatically.
✎✎ There should be no disc in the product when
you upgrade the software using the USB jack.
✎✎ When the system upgrade is done, check the
software details in the Product Information
section of the Contact Samsung screen.
✎✎ Do not turn off the product during the
software upgrade. It may cause the product to
malfunction.
✎✎ Software upgrades using the USB jack must
be performed with a USB flash drive only.
✎✎ To use the Auto update function, your product
must be connected to the Internet.
27 - English
Settings
1. Select Update now, and then press the OK
button. The Update now pop-up appears.
2. The product searches on line for the latest
software version.
3. If it does not find an update, the "There are
no new updates for you at the moment."
pop-up appears. Press the OK button to exit.
4. If it finds a new version, the Update Request
pop-up appears.
5. Select OK. The product upgrades the
software, turns off, and then turns on
automatically.
6. If you do not select OK or Cancel in one
minute, the product stores the new upgrade
software. You can upgrade the software later
using Auto update.
7. If you select Cancel, the product cancells the
upgrade.
2. Click OWNERS & SUPPORT on the top
right of the page, and then select Manuals
& Downloads from the drop down that
appears.
Playing Content
Your home cinema can play content located on
Blu-ray/DVD/CD discs, USB devices, PCs, smart
phones, tablets, and on the Web.
To play content located on your PC or a mobile
device, you must connect the PC or mobile device
and the product to your network. To play content
on your PC, you must also download and install
DLNA network software or already have DLNA
network software on your PC.
✎✎ PCs running Windows 7 and Windows 8 have
DLNA software (Play To) built in.
-- When cleaning, wipe gently from the inside
to the outside of the disc.
-- Disc Storage
`` Do not keep in direct sunlight.
`` Keep in a cool ventilated area.
`` Keep in a clean protective jacket and
store vertically.
Playing Multimedia Files
1. In the Home screen, select MULTIMEDIA,
and then press the OK button. The Recently
Played screen appears.
Playing Commercial Discs
1. Press the ^ button to open the disc tray.
2. Place a disc gently into the disc tray with the
disc’s label facing up.
2. Select Storage, Network Device at the
bottom of the screen.
●● Storage - Displays storage devices
connected to the product.
●● Network Device - Displays mobile devices,
PCs, tablets, and similar devices connected
through the network.
✎✎ When you select an item, information about
the item scrolls across the bottom of the item's
listing window.
3. Press the ^ button to close the disc tray.
Playback starts automatically.
4. If playback does not start automatically, press
the p button on the remote.
Disc Storage & Management
●●
●●
Holding Discs
-- Fingerprints or scratches on
a disc may reduce sound and
picture quality or cause skipping.
-- Avoid touching the surface of a disc where
data has been recorded.
-- Hold the disc by the edges so that fingerprints
will not get on the surface.
-- Do not stick paper or tape on the disc.
Cleaning Discs
-- If you get fingerprints or dirt
on a disc, clean it with a mild
detergent diluted in water and
wipe with a soft cloth.
3. Select an item or device, and then press
the OK button. A screen appears listing the
contents of the item or device. Depending
on how the contents are arranged, you will
see either folders, individual files, or both.
4. If necessary, use the 78:; buttons to
select a folder, and then press the OK button.
5. Use the 78:; buttons to select a file to
view or play, and then press the OK button.
6. The selected file plays.
7. Press the ' (RETURN) button to exit a folder
or the e (EXIT) button to return to the
Home screen.
8. Go to pages 30~42 for instructions that
explain how to control playback of videos,
music, and pictures on a storage device.
✎✎ To list only one type of media file, use the Filter
( ) function in the top-right corner of the
item or device screen.
28 - English
✎✎ In the Filter(
) drop down, select Photos,
Videos, or Music.
✎✎ Even though the product will display folders
that contain all content types, it will only
display files of the content type you selected
For example, if you selected Music, you will
only be able to see music files.
Playing Files on a Storage Device
Method 1 : If the product is turned on after
you connect a storage device
1. Turn the product on.
Method 2 : If you connect a USB device while
the product is turned on
1. Connect the storage device to the product.
(a recorded CD, a USB device, etc.) The "New
device connected." pop-up appears. If two or
more storage devices are connected, use the
:; buttons to switch between devices.
PLAY DISC
MULTIMEDIA
SAMSUNG APPS
STORAGE DEVICE
) drop down, select Photos,
Videos, or Music.
✎✎ Even though the product will display folders
that contain all content types, it will only
display files of the content type you selected
For example, if you selected Music, you will
only be able to see music files.
3. If necessary, use the 78:; buttons to
select a folder, and then press the OK button.
4. Select a file to view or play, and then press
the OK button.
5. Press the ' (RETURN) button to exit a folder
or the e (EXIT) button to return to the
Home screen.
6. Go to pages 30~42 for instructions that
explain how to control playback of videos,
music, and pictures on a storage device.
✎✎ If you insert a disc while playing a USB device
or phone, the device mode changes to "Disc"
automatically.
✎✎ If your cellular phone is DLNA compatible,
you can play content on the phone without
connecting a USB cable.
You can play media content on the Home cinema
that is stored on a computer or mobile device
connected to the same network as the Home
cinema.
All
Photos
No Disc
✎✎ In the Filter(
Playing Media Content Saved on a
Computer/Mobile Device
New device connected.
Videos
RECOMMENDED
Filter( ) function in the top-right corner of
the item or device screen.
MY APPS
Music
✎✎ You may experience compatibility issues when
App 1
App 2
App 3
App 4
App 5
App 6
Screen Mirroring
Source
Settings
✎✎ If the pop-up does not appear, go to Method
1.
2. Use the 78 buttons to select All, Photos,
Videos, or Music, and then press the OK
button. Depending on how the contents
are arranged, you will see either folders,
individual files, or both.
attempting to play media files via a third-party
DLNA server.
✎✎ The content shared by a computer or a
mobile device may not play depending on the
encoding type and file format of the content.
In addition, some functions may not be
available.
✎✎ The media content may not play smoothly
depending on the network status. If this
occurs, use a USB storage device.
29 - English
Playing Content
2. Follow the directions in “Playing Multimedia
Files” on page 28. In Step 2, select
Storage.
✎✎ To list only one type of media file, use the
Playing Content
1. In the Home screen, select MULTIMEDIA, and
then press the OK button.
2. Select Network Device at the bottom of
the screen, and then press the OK button.
Storages devices connected to the same
network as the Home cinema are listed.
3. Select a storage device, and then press the
OK button. The folders and files shared by
the selected storage device are listed.
4. If necessary, use the 78:; buttons to
select a folder, and then press the OK button.
Controlling Video Playback
You can control the playback of video content
located on a Blu-ray/DVD disc, USB device, mobile
device, or PC. Depending on the disc or contents,
some of the functions described in this manual
may not be available.
Buttons on the Remote Control used
for Video Playback
5. Select a file to view or play, and then press
the OK button.
1
6. Press the ' (RETURN) button to exit a folder
or the e (EXIT) button to return to the
Home screen.
2
7. Go to pages 30~42 for instructions that
explain how to control playback of videos,
music, and pictures on a storage device.
✎✎ To list only one type of media file, use the
Filter( ) function in the top-right corner of
the item or device screen.
✎✎ In the Filter(
) drop down, select Photos,
Videos, or Music.
✎✎ Even though the product will display folders
that contain all content types, it will only
display files of the content type you selected
For example, if you selected Music, you will
only be able to see music files.
✎✎ Alternatively, move to the media content
to play and press the OK button to play the
content.
sing the disc menu, title menu, popup
1U
menu, and title list
DISC MENU
During playback, press this button to display
the Disc menu.
TITLE MENU
During playback, press this button to display
the Title menu or Popup menu.
●● If your disc has a playlist, press the Sort By
button to go to the playlist.
2 Playback related buttons
The product does not play sound in Search, or
Slow mode.
●● To return to normal speed playback, press the
p button.
30 - English
p
e (EXIT)
Select Scene
Starts/Pauses playback.
Stops playback.
Fast
Motion
Play
During playback, press and hold
the [ or ] button.
Each time you press and hold
the [ or ] button, the
playback speed will change.
Slow
Motion
Play
In pause mode, press and hold
the ] button.
Each time you press and hold
the ] button, the playback
speed will change.
During playback, press the [
or ] button.
Each time you press the [ or
] button, the disc moves to
the previous or next chapter or
file.
✎✎ If the index information in the file is
damaged or the file does not support
indexing, you will not be able to use the
Select Scene function.
✎✎ If you are using the DLNA function after
connecting to a computer through
your network, Select Scene may not be
supported.
Search Titles : If there is more than one
movie on the disc or device, select to start a
different title.
1. Select Search Titles, and then press the
OK button.
2. Use the 78 buttons to select a title,
and then press the OK button.
✎✎ To search in a DVD title, press and hold the
TOOLS button while playback is stopped.
Enter the number 00 and then desired
chapter/track number (01, 02, … etc.).
Using the TOOLS Menu
Commercial Discs
Chapter Search : Select to play the chapter of
your choice.
During playback, press the TOOLS button.
File-based Video
During playback, press the TOOLS button.
Use the :; buttons to select Settings(T) in the
upper right corner, and then press the OK button.
Play from the beginning
Select to return to the beginning of the movie,
and then press the OK button.
3D
Use 3D menu to select the Side by Side or
Top Bottom option if the 3D content currently
playing does not appear properly in 3D mode.
✎✎ Use 3D menu for 3D content only. If you
apply the Side by Side or Top Bottom format
to 2D content, it will not be displayed
properly.
1. Select Chapter Search, and then press
the OK button.
2. Use the 78 buttons to select a chapter,
and then press the OK button.
Search Time Bar : Select to play the movie
from a selected time point.
1. Select Search Time Bar, and then press
the OK button.
2. Press and hold the 123 button until the
Num pad appears on the screen. When
the Num pad appears, select a number
using the ,.:; button and then press
the OK button.
✎✎ You can also use the:; buttons to
advance or rewind the movie. The movie
advances or rewinds one minute each time
you press the :; buttons.
31 - English
Playing Content
Skip
Motion
Play
You can use the Select Scene function during
playback to view or start a movie from the
scene of your choice.
Playing Content
Repeat Mode
Equaliser Settings
Lets you repeat a title, chapter, or specific
section.
-- Off : Select to return to normal playback.
-- Title : Choose to repeat a selected title.
-- Chapter : Choose to repeat a specific chapter.
-- Repeat A-B : Choose to repeat a specific
section.
Lets you set the equaliser.
1. Press the OK button at the point where
you want repeat play to start (A).
2. Press the OK button at the point where
you want repeat play to stop (B).
✎✎ Depending on the disc, the screen may not
display all repeat options.
✎✎ Off, Repeat One, and Repeat All appear
when you play a video recorded as a digital
file.
✎
✎ The screen may not display Chapter or
Title immediately. Continue to press the
78 buttons until your choice is inside the
applicable field.
✎✎ The screen may not display Repeat A-B
immediately. Continue to press the 78
buttons until Repeat A-B is inside the
applicable field.
✎✎ You must set point (B) at least 5 seconds of
playing time after point (A).
✎✎ Equaliser Settings only appears when
Equaliser Mode is On.
Audio
Select to set the desired audio language.
Audio Sync
In some cases when the product is connected
to a digital TV, the audio signal may not
synchronize with the video signal. If this occurs,
use Audio Sync to adjust the audio delay time
to match the video signal.
Subtitle
Lets you set the desired subtitle language.
Subtitle Settings
Lets you set the desired subtitle options.
Angle
To view a scene from another angle. The Angle
option displays the number of angles available
to view (1/1, 1/2, 1/3, etc.).
BONUSVIEW Video
BONUSVIEW Audio
Picture Mode
Lets you set the desired Bonusview option.
Lets you set the Picture Mode.
-- Dynamic : Increases sharpness and
brightness.
-- Standard : Choose this setting for most
viewing applications.
-- Movie : The best setting for watching movies.
-- User : Lets you adjust the sharpness and
noise reduction function respectively.
Rotate
✎✎ When you use the BD Wise function, this
menu will not appear.
Equaliser Mode
Set Equaliser Mode on to use the equaliser.
You can rotate the screen clockwise or
counterclockwise by 90 degrees.
Full Screen
Lets you set the size of the video image.
Choose Original, Mode1 (larger), or Mode2
(largest).
Information
Select to view video file information.
✎✎ Depending on the disc or storage device, the
Tools menu may differ.
✎✎ Video files with high bitrates of 20Mbps or
more strain the product’s capabilities and may
stop playing during playback.
32 - English
✎✎ The Sort By and Options menus are usually
Using the Sort By & Options Menus
Select the Filter( ) function, and then Videos to
display videos only.
✎✎ Even though the product will display folders
that contain all content types, it will only
display files of the content type you selected
For example, if you selected Videos, you will
only be able to see video files.
On the screen that lists the video files, use the
78:; buttons to select Sort By or Options in
the upper right, and then press the OK button.
Videos
Sort By
■■
■■
Date
Displays all the folders with videos by date. If
you select a folder, and then press OK button,
displays all the video files in the folder by
date.
Title
Displays all the video files on the media or
storage device by title.
Folder
Displays all the folders on the media or
storage device.
Controlling Music Playback
You can control the playback of music content
located on a DVD, CD, USB, mobile device, or PC.
Depending on the disc or contents, some of the
functions described in this manual may not be
available.
Buttons on the Remote Control used
for Music Playback
4
13
2
Options
■■
■■
Play Selected
Play Selected lets you create a playlist by
selecting specific files to play. It works
essentially the same way for all media. See
"Using Play Selected with a Commercial CD"
on page 36.
Send
Select Send to upload selected files to on-line
sites (Picasa, Facebook, etc.) or to devices.
To use Send with an on-line site, you need
to establish an account with the on-line site,
and then log in using the Log In function.
Send works essentially the same way for
music, photos, and videos. For general
instructions, see "Using the Send Function"
on page 41.
1
[ ] buttons : Move to the previous/
next track.
2
e (EXIT) button : Stops a track.
3
Fast Play (Audio CD [CD-DA] only)
During playback, press and hold the [
or ] button.
Each time you press and hold the [
or ] button, the playback speed will
change.
4
p button : Plays/Pause a track.
✎✎ Depending on the disc or storage device, the
Options and Sort By menus may differ. All
options may not be displayed.
33 - English
Playing Content
■■
available when you are viewing video files on
a USB flash drive, a PC, a disc you recorded
yourself, or a mobile device. They are usually
not available if you are viewing a commercial
Blu-ray, DVD, or CD disc.
Playing Content
Music Screen Controls
Rewind the track.
TRACK 001
TRACK 001
00:00/00:00
00:43
TRACK 002
03:56
TRACK 003
04:41
TRACK 004
04:02
TRACK 005
03:43
TRACK 006
03:40 1
TRACK 007
04:06
TRACK 008
03:52
TRACK 009
03:04
TRACK 010
04:02
The Track List screen appears initially, and the
first track begins to play. If you are playing a
commercially recorded disk and don't press a
button on the remote momentarily, the Playback
screen appears. To return to the Track List screen,
press the ' (RETURN) button.

1
1
,
1
1
00:03:35
Repeat one track or all tracks.
Play tracks in random order.
Display the Equaliser.
On the
Music List
screen only.
TRACK 001
00:00:40
Advance the track.
Equaliser Settings : Adjust the
equaliser manually. (Available
only when Equaliser Mode is on)
Play Selected : Play Selected
lets you select specific files to
play. It works essentially the
same way for all media. See
"Using Play Selected with SelfRecorded Media (CDs, USB
Devices, etc.)" on page 36.
Ripping : The Ripping function
converts CD audio to the
mp3 format and saves the
converted files on a USB device
or a mobile device connected
to the product. See Ripping on
page 38.
Information : Shows the track
information.
To access the controls, play a track, and then use
the 78:; buttons to move to the control of
your choice.
✎✎ The music screen controls are only accessible
On the Track List screen, use 78 buttons to
move the highlight to the track you want. Press
the OK button to play the track.
On Screen Music Controls
1
when a track is playing.
✎✎ All controls do not appear at the same time.
✎✎ For file-based contents, the available Settings
(
) options will differ.
Using the Sort By & Options Menus
Pause a track.
Select the Filter( ) function, and then Music to
display music files only.
Play a track.
✎✎ Even though the product will display folders
Move to the previous track.
1
Move to the next track.
that contain all content types, it will only
display files of the content type you selected
For example, if you selected Music, you will
only be able to see music files.
34 - English
On the screen that lists the music files, use the
78:; buttons to select Sort By or Options in
the upper right, and then press the OK button.
Music
Sort By
■■
■■
■■
■■
Options menu may differ. All options may not
be displayed.
✎✎ Rename Playlist and Delete Playlist appear only
if a playlist exists.
Repeating Tracks on an Audio CD
Track
Displays all the music tracks on the media or
storage device.
Album
Displays all the music on the media or
storage device by album.
Artist
Displays all the music files on the media or
storage device by artist
Genre
Displays all music on the media or storage
device by genre.
Folder
Displays all the folders on the media or
storage device.
You can set the product to repeat tracks on an
audio CD (CD-DA/MP3).
1. On the Track List screen during playback,
in the
use the 78:; buttons to select
lower left corner of the screen, and then
press the OK button.
1
2. Use the 78 to select the Repeat mode you
want - Off, One Song, or All - and then press
the OK button.
TRACK 001
Options
■■
■■
■■
■■
■■
■■
Play Selected
Play Selected lets you select specific files to
play. It works essentially the same way for
all media. See "Using Play Selected with a
Commercial CD" on page 36 and "Using
Play Selected with Self-Recorded Media (CDs,
USB Devices, etc.)" on page 36.
Send
Select Send to upload selected files to on line
sites (Picasa, Facebook, etc.) or to devices. To
use Send, you need to establish an account
with the on-line site, and then log in using
the Log In function. Send works essentially
the same way for music, photos, and videos.
For general instructions, see "Using the Send
Function" on page 41.
Encoding
Select to manage the text encoding options.
Rename Playlist
Lets you modify the name of a playlist.
Delete Playlist
Lets you delete a playlist.
Add to Playlist
Lets you add additional files to a playlist.
TRACK 001
00:00/00:00
00:43
TRACK 002
03:56
TRACK 003
04:41
TRACK 004
04:02
TRACK 005
03:43
TRACK 006
03:40
TRACK 007
04:06
TRACK 008
03:52
TRACK 009
03:04
TRACK 010
04:02
Track List screen

TRACK 001
00:00:40
00:03:35
Playback screen
Press the ' (RETURN) button on the remote to
return to the Track List screen.
35 - English
Playing Content
■■
✎✎ Depending on the disc or storage device, the
Playing Content
Shuffling Tracks on an Audio CD
You can set the product to play tracks on an audio
CD (CD-DA/MP3) at random.
1. During playback, use the ,.:; buttons
in the lower left corner of the
to select
screen, and then press the OK button.
2. Use the 78 to set the Shuffle mode Off or
On, and then press the OK button.
1
Using Play Selected with a Commercial
CD
1. On the Track List screen, select Settings ( )
on the bottom left, and then press the OK
button. The Settings menu appears.
2. Select Play Selected, and then press the OK
button. The Play Selected screen appears.
3. Use the 78 buttons to select a track, and
then press the OK button. A check appears
to the left of the track.
4. Repeat Step 3 to select and check additional
tracks.
5. To remove a track from the list, move to the
track, and then press the OK button again.
The check on the track is removed.
6. When done, select Play on the bottom
left, and then press the OK button. The
Track List screen reappears listing only the
tracks you checked. The selected tracks play
automatically.
7. To cancel the Play Selected list, select Settings
( ) on the bottom left of the Track list
screen. On the Settings menu select Play All.
The Track List screen reappears with all tracks
on the CD listed.
✎✎ You can select up to 99 tracks from an Audio
CD (CD-DA) using Play Selected.
✎✎ On the Play Selected screen, you can also
choose Select All, Clear All, and Cancel.
- Use Select All to select all tracks. This cancels
your individual track selections. When you
press the ' (RETURN) button on your remote
or select Play and then press the OK button,
all tracks will appear on the Track List screen,
and the product will begin to play all tracks
from Track 001.
- Use Clear All to deselect all selected tracks
at once. Then, select individual tracks or
use Select All to select all the tracks, and
then press the ' (RETURN) button on your
remote or select Play and then press the OK
button. If you do not use Select All or select
individual tracks, the Play Selected list will
not change.
- Cancel cancels any changes you made on the
Play Selected screen. When you return to the
Track List screen, the Play Selected list will be
unchanged.
Using Play Selected with Self-Recorded
Media (CDs, USB Devices, etc.)
1. Insert a self-recorded CD or USB device with
self-recorded files into the home cinema. The
New device connected. pop-up appears.
2. Select Music, and then press the OK button
on your remote. The File List screen appears
displaying icons for tracks, folders, or both.
3. If necessary, use the 78:; buttons to
select a folder, and then press the OK button.
4. When the tracks you want to play are
displayed, select Options in the upper right,
and then press the OK button.
5. Select Play Selected, and then press the OK
button. Check boxes appear on the upper
left sides of the track icons.
6. Use the 78:; buttons to select a track,
and then press the OK button. A check
appears in the check box.
7. Repeat Step 6 to check and select additional
tracks.
8. To remove a track from the list, move to the
track, and then press the OK button again.
The check on the track is removed.
9. When done, select Play, and then press the
OK button. The Track List screen appears
listing only the tracks you checked. The
selected tracks play automatically.
10. To cancel the Play Selected list, press the '
(RETURN) button or the e (EXIT) button. If
you press ' (RETURN), you return to the File
List screen. If you press e (EXIT), you go to
the Home screen.
36 - English
✎✎ If you want to use Play Selected to watch
videos, use the Filter( ) function to select
Videos instead of Music.
Using Play Selected Starting from the
Home Screen
✎✎ Select PLAY DISC or MULTIMEDIA depending
on the media you are using.
- If you selected PLAY DISC, the Track List
screen appears. Use the Filter( ) function
to select Music, and then follow the
directions starting at Step 3 above.
Creating and Editing a Playlist Stored in
a Storage Device
Playing a playlist
1. Connect the USB device with the playlist to
the home cinema's USB port.
Creating a playlist
2. Navigate to the playlist (Home screen ;
MULTIMEDIA ; Storage ; USB device ;
playlist).
1. Connect a USB device with stored music to
the home cinema's USB jack, and then turn
on the home cinema.
3. Select the playlist, and then press OK. The
Track List screen appears and the first track
of the playlist starts to play.
2. On the Home screen, select MULTIMEDIA,
and then press the OK button.
3. On the MULTIMEDIA screen, select Storage,
and then press the OK button.
4. Select the USB device, and then press the OK
button.
Editing a playlist
5. At the top of the screen, select Filter( ) ;
Music.
6. After the screen re-displays, select Options
( ) ; Add to Playlist.
7. On the next screen, select an existing playlist,
and then press the OK button.
OR
Select New Playlist, and then press the OK
button. If you selected an existing playlist, go
to Step 9. If you selected New Playlist, go to
Step 8.
1. While playing a playlist, select Settings
) ; Edit Playlist at the bottom-left corner
of the Track List screen.
(
2. Use the 78:; buttons to select a track,
and then press the OK button. A check mark
appears next to the track.
3. To cancel a selection, select the track again,
and then press the OK button.
✎✎ To select all tracks at once, use Select All. To
cancel all selections at once, use Deselect All.
37 - English
Playing Content
- If you selected MULTIMEDIA, select Storage
or Network Device on the MULTIMEDIA
screen. Then, select your storage media on
the Storage screen or device on the Network
Device screen. The File List screen appears.
Use the Filter( ) function to select Music,
and then follow the directions starting at
Step 3 above.
8. On the on-screen keyboard, accept the
default name for the new playlist or enter
a new name. When finished, select Done,
press OK, and then go to Step 9.
9. Navigate to the screen that displays the
music you want to put into the playlist.
10. Use the 78:; buttons to select a track,
and then press the OK button. A check
appears in the check box on the left side of
the track icon.
11. Repeat Step 10 to check and select additional
tracks.
12. To remove a track from the list, move to the
track, and then press the OK button again.
The check on the track is removed.
13. When finished, select Add at the top of the
screen, and then press the OK button. The
playlist is saved to the USB device and the
Added pop-up appears. Press the OK button.
Playing Content
4. When finished, select Delete at the bottom
left of the screen, and then press the OK
button.
A confirmation pop-up appears.
5. Select Yes, and then press the OK button.
✎✎ Deleting all files included in a playlist will
10. If you want to cancel ripping after ripping
has begun, press the OK button and then
select Yes. Select No to continue ripping.
11. When ripping is complete, the "Successfully
ripped." message appears. Press the OK
button. The Track List screen reappears.
delete the playlist itself, too.
Using Bluetooth
✎✎ You can save up to 5 playlists.
Ripping
1. Insert a USB device into the USB jack on the
front of the product. This is the device you
will rip the files to.
2. Put a music CD into the home cinema. In a
few moments, the Track List screen appears.
3. On the Track List screen, select Settings
( ) on the lower left of the screen, and
then press the OK button. The Settings menu
appears.
4. Use the 78 buttons to select Ripping, and
then press the OK button. The Ripping screen
appears.
5. Use the 78 buttons to select a track, and
then press the OK button. A check appears
to the left of the track.
6. Repeat Step 5 to select and check additional
tracks.
✎✎ To select all tracks at once, select Select All on
the bottom left of the screen, and then press
the OK button.
7. To remove a track from the list, move to the
track, and then press the OK button again.
The check on the track is removed.
8. When done, select the Rip button using the
78 buttons, and then press the OK button.
The Rip pop-up appears.
9. Use the 78 buttons to select the device to
store the ripped files to, and then press the
OK button. Ripping begins.
✎✎ Do not disconnect the device while ripping is
You can use a Bluetooth device to enjoy music
with high quality stereo sound, all without wires!
●●
●●
Pairing distance : max. 2M,
Operating distance : max. 10M
Actual Bluetooth performance may differ
depending on your environment, even if
you use your Bluetooth device within the
specified operating distance.
What is Bluetooth?
Bluetooth is a technology that enables Bluetoothcompliant devices to interconnect with each other
easily using a short, wireless connection.
●● A Bluetooth device may hum or malfunction:
-- When a part of your body is in contact with
the receiving/transmitting system of the
Bluetooth device or the Home Cinema.
-- When the device is subject to electrical
variation from obstructions caused by a wall,
corner, or office partitioning.
-- When the device is exposed to electrical
interference from same frequency-band
devices including medical equipment,
microwave ovens, and wireless LANs.
●● Pair the Home Cinema with the Bluetooth
device while the two are close together.
●● The further the distance is between the Home
Cinema and the Bluetooth device, the worse
the quality is.
If the distance exceeds the Bluetooth
operational range, the connection is lost.
●● In poor reception areas, the Bluetooth
connection may not work properly.
in progress.
38 - English
●●
●●
The Home Cinema has an effective reception
range of up to 10 meters in all directions if
there are no obstacles. The connection will be
automatically cut off if the device is out of this
range. Even within this range, the sound quality
may be degraded by obstacles such as walls or
doors.
This wireless device may cause electrical
interference. during its operation.
To connect the Home Cinema to a Bluetooth
device
✎✎ The AVRCP feature is supported. It's
functionality will differ, depending on the
specifications of the connected device.
✎✎ Connect only to a Bluetooth device that
supports the A2DP Profile.
✎✎ Only one Bluetooth device can be paired at a
time.
✎✎ The search or connection functions may not
work properly in the following cases:
-- If there a strong electric field near or around
the home cinema.
-- If several Bluetooth devices are simultaneously
paired with product.
-- If the Bluetooth device is turned off, not in
place, or malfunctions.
Connect
1. Press the SOURCE button on the remote
control to display the BT message.
✎✎ For the best operational compatibility between
the home cinema and a Bluetooth device or
any other device, such as a Mobile Phone, we
recommend you update the device's OS to the
latest version.
2. Select the Bluetooth menu on the Bluetooth
device you want to connect. For instructions,
refer to the Bluetooth device's manual.
To disconnect the Bluetooth device from the
3. Select "[HTS]Jxxxxx" from the list.
●● When the Home Cinema is connected to
the Bluetooth device, the device name of
the connected Bluetooth device, followed
by the name of home cinema, will appear
on the front display of the home cinema.
You can disconnect the Bluetooth device from
the Home Cinema. For instructions, refer to the
Bluetooth device's manual.
●● When the Home Cinema is disconnected from
the Bluetooth device, the Home Cinema will
display DISCONNECTED on the front display.
4. Play music on the connected device.
●● You can listen to the music playing on the
connected Bluetooth device over the Home
Cinema system.
✎✎ The Home Cinema only supports Middle
Quality SBC data (up to 237kbps@48kHz),
and does not support High Quality SBC data
(328kbps@44.1kHz).
Home Cinema
To disconnect the Home Cinema from the
Bluetooth device
Press the (F) button on the front panel of the
Home Cinema to switch from BT to another mode
or turn off the Home Cinema.
●● Except when you disconnect the Home Cinema
by changing functions, the connected Bluetooth
device will wait a certain amount of time for
a response from the Home Cinema before
terminating the connection. (Disconnection
time may differ, depending on the Bluetooth
device.)
39 - English
Playing Content
Bluetooth device
Before you begin, confirm that the Bluetooth
device supports the Bluetooth compliant stereo
headset function.
Note that such devices as microwave ovens,
wireless LAN adapters, fluorescent lights, and
gas stoves use the same frequency range as
the Bluetooth device, and can cause electric
interference.
Playing Content
✎✎ In Bluetooth connection mode, the Bluetooth
connection will be lost if the distance
between the Home Cinema System and the
Bluetooth device exceeds 10 meters. When
the Bluetooth device comes back into effective
range or you restart the Bluetooth device, you
will have to pair the device and home cinema
again to reconnect.
✎✎ In Bluetooth mode, the screen saver will start
if the Bluetooth device stays in the Ready state
for 5 minutes. To reconnect the Bluetooth
device, turn off the screen saver, and then
connect the device. To turn off the screen
saver, press any button on the remote control
(the Volume button, an 78:; buttons,
etc.).
Playing Photo Content
You can play photo content located on a DVD,
USB, mobile device, or PC.
Using the Tools Menu
While displaying a photo, press the TOOLS button
on the remote.
Select Settings(T) in the upper right corner of
the screen, and then press the OK button. The
Tools menu drop down list appears.
Slideshow Settings
■■
■■
Using the Bluetooth Quick start
Speed : Select to set a slide show's speed.
Effects : Select to set a slide show's special
effects.
When the home cinema is turned off, connecting
a previously connected smart device to the product
via a Bluetooth connection can turn the home
cinema on.
Rotate
✎✎ The home cinema must be plugged in for
Zoom
Quick start to work.
✎✎ To use this function, set Settings > System >
Quick start to On.
✎✎ To use this function, the Bluetooth connection
between the home cinema and your smart
device should have been established before.
In other words, the home cinema should be
found on the list of Bluetooth devices your
smart device has already connected to.
1. Connect your previously connected smart
device to the product via Bluetooth. (For
information on Bluetooth connections, refer
to your smart device’s manual.)
2. Once connected, the home cinema turns
itself on automatically in BT mode.
●● Select the desired music to play on your
smart device.
Select to rotate the picture. (This will rotate the
picture either clockwise or counter clockwise.)
Select to enlarge the current picture. (Enlarge
up to 4 times)
Picture Mode
■■
■■
■■
■■
Dynamic : Choose to increase sharpness.
Standard : Choose for most viewing
applications.
Movie : This is the best setting for watching
movies.
User : Lets you adjust the sharpness and
noise reduction function respectively.
Background Music
Select to listen to music while viewing a slide
show.
Equaliser Mode
Set to On to use the equaliser. Customize your
own personal sound preferences using the
equaliser settings.
Equaliser Settings
This function is only available when Equaliser
Mode is On.
40 - English
Send
Photos
Select Send to upload selected files to on-line
sites (Picasa, Facebook, etc.) or devices. To use
Send with an on-line site, you need to establish
an account with the on-line site, and then
log in using the Log In function. Send works
essentially the same way for music, photos, and
videos. For general instructions, see "Using the
Send Function" on page 41.
Information
Sort By
■■
■■
■■
Displays the picture information.
✎✎ Depending on the disc or storage device, the
Using the Sort By and Options Menus
When the Photo File List is Displayed
Select the Filter( ) function, and then Photos to
display photos only.
✎✎ Even though the product will display folders
that contain all content types, it will only
display files of the content type you selected
For example, if you selected Photos, you will
only be able to see photo files.
On the screen that lists the photo files, use the
78:; buttons to select Sort By or Options in
the upper right, and then press the OK button.
Options
■■
■■
■■
Slide Show
Starts the slide show. Shows all the files in
the current folder, one after another. If you
want to create a slide show with a selected
group of photos, see Play Selected below.
Play Selected
Play Selected lets you select specific files to
play. It works essentially the same way for all
media. See "Using Play Selected with SelfRecorded Media (CDs, USB Devices, etc.)" on
page 36.
Send
Select Send to upload selected files to on line
sites (Picasa, Facebook, etc.) or to devices.
To use Send with an on-line site, you need
to establish an account with the on-line site,
and then log in using the Log In function.
✎✎ Depending on the disc or storage device, the
Options menu may differ. All options may not
be displayed.
Using the Send Function
1. Use the 78 buttons to select Send, and
then press the OK button. The Selection
screen appears.
2. Use the 78 buttons to select a picture, and
then press the OK button. A check appears
to the left of the picture.
3. Repeat Step 2 to select and check additional
pictures.
4. To remove a picture from the list, move to
the picture, and then press the OK button
again. The check on the picture is removed.
41 - English
Playing Content
Options menu may differ. All options may not
be displayed.
✎✎ To enable the Background Music function, the
photo file must be in the same storage media
as the music file. However, the sound quality
can be affected by the bitrate of the MP3
file, the size of the photo, and the encoding
method.
✎✎ You can't enlarge the subtitle and PG graphic
in the full screen mode.
Date
Groups all the photo files on the media or
storage device by date. Click a group to see
the photos in that group.
Title
Displays all the photo files on the media or
storage device by title.
Folder
Displays all the folders on the media or
storage device.
Playing Content
5. When done, press the 78 button to select
Send, and then press the OK button. The
Send pop-up appears listing the on-line sites
(Picasa, Facebook, etc.) or devices that you
can send the photos to.
6. Select a destination, and then press the OK
button.
7. If you are sending the photos to an on-line
site, the site starts. Log in and follow the
directions on the screen.
✎✎ To send photos to an on-line site, you must
have an account with that site.
Using the Special Effects Remote
Control Buttons
SOUND EFFECT Function
Virtual Surround
ĞĞ
SFE Mode
zzSymphony Hall in Boston (Hall 1) : Provides a
clear vocal as if listening in a concert hall.
zzPhilharmonic Hall in Bratislava (Hall 2) :
Also provides a clear vocal as if listening in a
concert hall, but less powerful than HALL1.
zzJazz Club in Seoul B : Recommended setting
for Jazz.
zzChurch in Seoul : Gives the feel of being in a
grand church.
zzAmphitheater (Rock) : Recommended setting
for Rock.
zzOff : Select for normal listening.
ĞĞ
Sports
✎✎ Depending on the disc or storage device,
Lets you select a mode that optimizes the
sound.
name of this function may differ.
1. Press the SOUND EFFECT button.
2. P
ress the 78 buttons to select the desired
mode: DSP, Virtual Surround, SFE Mode, or
Sports.
3. P
ress the :; buttons to select the desired
sound effect.
ĞĞ
ĞĞ
You can set a two-channel input source to
produce sound in 5.1 channel surround mode.
DSP
zzMP3 Enhancer : Helps enhance your sound
experience (ex. mp3 music). You can upscale
your MP3 level sound (24 kHz, 8bit) to CD
level sound (44.1 kHz, 16bit).
zzPower Bass : Increases the volume level of
bass tones and provides thudding sound
effects.
zzVirtual 7.1 (HT-J7500W only) : Creates a
virtual 7.1 CH sound using the 5.1 CH speaker
system.
zzOff : Select for normal listening.
zzAnnouncer : Emphasizes the commentator's
voice during a sports game to increase your
absorption in the game.
zzStadium : Emphasizes spectators' cheering
during a sports game to add immediacy.
zzOff : Select for normal listening.
DTS Neo:Fusion II / 3D Sound
You can enjoy more natural and vivid surround
sound with enriched tones by adjusting the
depth of sound using the level options.
●● DTS Neo:Fusion II : Off  On
●● 3D Sound (HT-J7500W only) :
Off  High  Low
✎✎ 3D Sound is not available in FM mode.
✎✎ The 3D Sound is displayed only if you
✎✎ If selecting the Simple Speaker Setup >
Simple Mode, the DSP is displayed as
following. (Simple Speaker Setup function is
available only in the HT-J7500W model.)
Enhanced Stereo  Mp3 Enhancer  Power
Bass  Virtual Surround
* Enhanced Stereo : A sound field effect
that makes the sound from front channel
extend to the surround channel.
42 - English
selected Simple Speaker Setup > Simple
Mode.
Network Services
You can enjoy various network services such as
streaming video or on-line apps by connecting the
product to your network.
To use network services, you must first:
✎✎ If you selected Sign me in automatically,
the next time you log in, the product will
automatically enter your e-mail and password.
All you need to do is select Sign In.
✎✎ If you press the
button after you have
logged in, the Sign In screen appears. You
can select Link Accounts, Edit Profile, Remove
Account, and Sign Out.
1. Connect the product to a network.
(See page 14)
2. Configure the network settings.
(See pages 23~25)
Before Using SAMSUNG APPS
Logging In to Your Samsung
Account
Before you access SAMSUNG APPS, we suggest
you log in to your Samsung account.
✎✎ If you do not have a Samsung account, create
one by selecting Create Account.
1. With the Home screen displayed, press the
button. The Sign In screen appears.
1. On the Home screen, select SAMSUNG APPS,
and then press the OK button.
2. The Smart Hub pop-up appears asking if
you want to set up Smart Hub. Select Yes,
and then press the OK button. The Welcome
screen appears.
2. Select the ID field, and then press the OK
button. The keyboard pop-up appears.
3. Select Start, and then press the OK button.
The Smart Hub Terms & Conditions, Privacy
Policy screen appears.
3. Using the keyboard, enter your e-mail
address. When finished, select the Done
button, and then press the OK button. The
Sign In screen re-appears.
4. On the Additional Services and Options
screen, you must review and agree to both
the Smart Hub Terms and Conditions and the
Privacy Policy to use Smart Hub.
4. Select the Password field, and then press the
OK button. The keyboard pop-up appears.
5. Scroll down, and then click the View details
buttons to review the full documents.
5. Using the keyboard, enter your password.
When finished, select the Done button, and
then press the OK button. The Sign In screen
re-appears.
✎✎ You do not need to consent to the
6. To make the log in process easier next time,
select Sign me in automatically, and then
press the OK button.
Supplemental Privacy Notice, but one or more
Smart TV features or functionalities may not
be available if you do not.
6. Select I agree to all, and then press the OK
button. The Setup Complete screen appears.
Press the OK button.
7. Select Sign In, and then press the OK button.
8. The Samsung account Terms and Conditions
screen appears.
9. Select I agree, and then press the OK button.
10. Select an image you want to use to identify
your account, and then press the OK button.
11. Select Done.
43 - English
Network Services
To create a Samsung account, follow these steps:
If you haven’t set up Smart Hub, when you use
SAMSUNG APPS for the first time, the product
will ask you to perform the Smart Hub set up
procedure.
Network Services
Using SAMSUNG APPS
Through the SAMSUNG APPS screen, you can
download applications from the Internet, and
launch and run downloaded applications on your
TV. To access some applications, you need to have
a Samsung account.
✎✎ While playing multimedia content in SAMSUNG
APPS, press and hold 5 button on the remote
to pause playback. To stop playback, press and
hold e (EXIT) button on the remote.
The SAMSUNG APPS Screen at a Glance
1
2
Downloading an App
SAMSUNG APPS
1. Select Most Popular, What's New, or
Categories, and then press the OK button.
RECOMMENDED
1
2
3
4
5
2
3
4
5
2. If you selected Categories, select a category
icon, and then press the OK button.
Otherwise, go to Step 3.
MY APPS
WebBrowser
The first time you open the SAMSUNG APPS
screen, the Home cinema automatically
downloads a group of free apps. Once these
apps have been downloaded, they appear on the
SAMSUNG APPS screen. To see additional apps,
select Most Popular, What's New, or Categories
on the bottom of the screen, and then press the
OK button.
Most Popular displays the most popular apps,
What's New the newest. Categories displays a
series of icons representing categories such as
Video, Game, and Sports. Select a category icon,
and then press the OK button. The Home cinema
displays the apps in that category.
6
Most Popular What's New
7
8
9
10
✎✎ On the Most Popular, What's New, and
Categories screens, a green arrow is displayed
on apps you have already downloaded.
3. Select an app you want to download,
and then press the OK button. The Detail
Information screen for the App appears.
Categories
3
1
RECOMMENDED : Displays recommended
contents managed by Samsung. You
cannot delete Recommended Apps.
2
MY APPS : Displays your personal gallery
of applications modifiable on the MY
APPS screen.
3
Most Popular, What’s New and Categories :
Select to view and download additional
apps.
4. Select the Download button on the screen,
and then press the OK button. Download
changes to Cancel and the app begins to
download.
5. If you want to cancel the download, select
Cancel, and then press the OK button.
6. When the download is complete, Cancel
changes to Open. Select Open, and then
press the OK button to start the application.
Alternately, press the ' (RETURN) button
until the SAMSUNG APPS screen reappears.
The app you downloaded will be displayed
on the App screen under MY APPS.
44 - English
Starting an Application
View Details
1. Select SAMSUNG APPS on the Home screen,
and then press the OK button.
1. On the MY APPS screen, select the app you
want to see detailed information for, and
then press the OK button for 3 seconds. The
Option menu appears.
2. On the SAMSUNG APPS screen, use the
78:; buttons to select an app, and then
press the OK button. The app starts.
The Option Menu
The Option menu lets you add apps to and delete
apps from MY APPS. It also lets you change the
position of an app in MY APPS and update apps.
Move
2. Select View Details, and then press the OK
button.
Change View
1. On the MY APPS screen, select an app, and
then press the OK button for 3 seconds. The
Option menu appears.
Delete
3. Select OK, and then press the OK button to
change the view.
1. On the MY APPS screen, select the app you
want to delete, and then press the OK button
for 3 seconds. The Option menu appears.
Lock/Unlock
2. Select Move, and then press the OK button.
3. Use the 78:; buttons to move the app.
2. Select Delete, and then press the OK button .
Locking an app makes it more difficult to delete
accidently.
3. Use the :; buttons to select Yes, and then
press the OK button.
1. On the MY APPS screen, select the app you
want to lock, and then press the OK button
for 3 seconds. The Option menu appears.
Delete Multiple
2. Select Lock/Unlock, and then press the OK
button.
1. On the MY APPS screen, select an app you
want to delete and then press the OK button
for 3 seconds. The Options menu appears.
2. Select the Delete Multiple, and then press
the OK button.
3. Use the 78:; buttons to select apps
you want to delete, and then press the OK
button.
4. Use the 8 button to select Delete, and then
press the OK button.
3. The PIN input pop-up appears. Enter your
PIN. Press and hold the 123 button until the
Num pad appears on the screen. When the
Num pad appears, select a number using the
button and then press the OK button.
,.
If you haven't set a PIN, enter the default
PIN: 0000.
4. A checkbox appears on each app icon. Use
the 78:; button to move to the app you
want to lock, and then press the OK button
to select it. A check mark appears on the
icon.
45 - English
Network Services
4. When the app is where you want it, press the
OK or e (EXIT) button.
2. Select Change View, and then press the OK
button. If the current view is Most Played,
you will be asked if you want to change to
Custom View. If the current view is Custom
View, you will be asked if you want to
change the view to Most Played. Most Played
sorts the apps by the number of times you
ran each app. Custom View lets you arrange
the apps to your liking.
1. On the MY APPS screen, select the app you
want to move, and then press the OK button
for 3 seconds. The Option menu appears.
Network Services
5. Repeat Step 4 to select other apps. Use
Select All or Deselect All on the bottom of
the screen to select or deselect all apps at
once. To deselect individual apps, select the
app again, and then press the OK button.
The check mark disappears.
6. When you have finished marking your
selections, move to Save on the bottom of
the screen, and then press the OK button.
7. A lock mark appears on the selected app’s
icon. You will be prompted to enter the PIN
number to delete or unlock a locked app.
Update Apps
1. On the MY APPS screen, select any app, and
then press the OK button for 3 seconds. The
Option menu appears.
2. Select Update Apps, and then press the OK
button.
3. The Update Apps screens lists all the apps
that have updates available. Select each app
you want to update, and then press the OK
button. You can also choose Select All to
update all the apps listed.
4. Select Update, and then press the OK button.
Screen Mirroring
The Screen Mirroring function lets you view the
screen of your smart phone or android tablet on
the TV you have connected to the product.
1. In the Home screen, select Screen Mirroring,
and then press the OK button.
2. Launch AllShare Cast or Screen Mirroring on
your device.
3. On your device, find the name of the product
in the list of available devices and then select
it.
4. The TV displays a connecting message (for
example, Connecting to Android_92gb...)
and then displays the connected message.
5. In a few moments, the screen of your device
appears on the TV screen.
✎✎ You can connect to a device that supports
AllShare Cast or Screen Mirroring. Note
that all devices that have AllShare Cast or
Screen Mirroring may not be fully supported,
depending on the manufacturer. For further
information on mobile connection support,
refer to the manufacturer’s web site.
✎✎ When you are using the Screen Mirroring
function, video stuttering or audio dropouts
may occur, depending on your environment.
✎✎ Bluetooth transmissions can interfere with
the Screen Mirroring signal. Before using
the Screen Mirroring function, we strongly
recommend that you turn off the Bluetooth
function on your smart phone or smart device
(tablet, etc.).
Using the Web Browser
You can access the Internet using the Web
Browser application.
1. Select SAMSUNG APPS on the Home screen
and then press the OK button.
2. On the SAMSUNG APPS screen, select
WebBrowser, and then press the OK button.
✎✎ When you run the Web Browser with the
product connected by HDMI to a BD Wise
compatible TV - and BD Wise is on - the
browser is maximized to fill the screen and the
TV's resolution is set to the optimal resolution
automatically.
✎✎ The Web Browser is not compatible with Java
applications.
✎✎ Flash Player contents cannot be played with
the Web browser.
✎
✎ If you attempt to download a file, and the file
cannot be saved, an error message will appear.
✎✎ E-commerce (purchasing products online) is
not supported.
✎✎ ActiveX is not supported.
✎✎ Access may be blocked to some websites or to
web browsers operated by certain businesses.
6. To stop Screen Mirroring, press the e
(EXIT) or ' (RETURN) button on the remote
control, or exit the Screen Mirroring function
on your smart phone.
46 - English
Link Browsing and Pointer Browsing
The Control Panel at a Glance
The Web Browser provides two types of browsing,
Pointer Browsing and Link Browsing. When you
launch the browser for the first time, Pointer
Browsing is active. If you are using a mouse to
navigate in the Web Browser, we recommend
leaving Pointer Browsing active. With Pointer
Browsing, you move the pointer using the
directional arrow keys on your remote. The pointer
moves freely around the screen, much like the
pointer on a computer when you use a mouse.
With Link Browsing, you use the directional arrow
keys to move a highlight from one link, button, or
entry field to the next. The highlight is restricted
to the links, buttons, and entry fields.
The Control Panel, which runs across the top
of the screen, has a series of icons which start
a number of useful functions. The icons are
described below, starting with the icon on the far
left of the screen.
http://www.samsung.com
100%
To activate Link Browsing, follow these steps:
●●
●●
●●
2. Press the OK button. Link Browsing is
activated and will remain active whenever
you bring up the Web Browser or until you
change to Pointer Browsing.
●●
●●
http://www.samsung.com
●●
http://www.samsung.com
●●
http://www.samsung.com
●●
http://www.samsung.com
●●
http://www.samsung.com
tp://www.samsung.com
www.samsung.com
100%
100%
100%
●●
●●
●●
http://www.samsung.com
: Moves to the
previous page.
: Moves tohttp://www.samsung.com
the next web page.
http://www.samsung.com
: Displays
the Bookmarks and History
screen. You can bookmark the current page,
select an existing bookmark, and edit and
delete bookmarks. You can also view your
browsing history and select a page to revisit.
http://www.samsung.com
: Moves
to the Home screen of the Web
Browser.
http://www.samsung.com : Lets you enter a page
address manually using the keyboard popup.
: Reloads the current 100%
page so that it is
refreshed on the screen.
: Adds the current 100%
page to your
bookmarks.
100%you search for
: Lets
information by entering words or characters
using the keyboard pop-up. See Using the
Keyboard Popup on the next page.
100% : Lets you enlarge or shrink the screen
by various percentages.
: Lets you switch between Pointer
/
Browsing and Link Browsing.
: Lets you configure the Browser’s settings.
See “Using the Settings Menu” on page 49.
: Closes the Web Browser.
47 - English
Network Services
1. Use the 78:; buttons on your remote to
move the pointer to the Link Browser icon on
the top right of the screen. The Link Browser
icon is the third icon from the right.
The pointer will be in the correct position
if the icon turns blue and the words “Link
Browsing” appear on the screen.
Network Services
Using the Keyboard Pop-up
Options on the Keyboard Pop-Up
http://www.samsung.com
When you click the
, the
or 100%
access a data or text entry 100%
field, and then press the OK button, the keyboard
pop-up appears.
//www.samsung.com
http://www.samsung.com
To access the keyboard pop-up
options, highlight
100%
the
button on the bottom left of the keyboard,
and then press the OK button.
Language
100%
Select the language for the keyboard. You can
select English, French, Russian, etc.
Recommend text
The keyboard suggests recommended words as you
enter text. You can turn this function On or Off.
As you enter characters, recommended text will be shown.
Caps
1
2
3
4
5
6
7
8
9
0
q
w e
r
t
y
u
i
o
p
^
*

j
k
l
~
@
!
Done
,
.
?
-
 


Cancel
/
123#& a
s
d
f
g
h
x
c
v
b
n
z
ENG
m
www. .com
Clear
:
To use the keyboard pop-up with your remote,
follow these steps:
1. Use the 78:; buttons on your remote to
move the highlight to a letter or number of
your choice.
2. Press the OK button to enter the letter or
number into the entry field.
3. To access capital letters, move the highlight
to the Caps key on the top left, and then
press the OK button. Press the OK button
again with the Caps key highlighted to access
small letters again.
Reset recommended text data
Reset erases the Samsung Keyboard's memory.
Select OK to erase everything that the Samsung
Keyboard has learned about your writing style,
including any new words you have used.
Predict Next Letter
The keyboard will predict the next letter as you
enter letters. The predictions appear in a ring
around the letter you have just entered. You
can select a predicted letter or move to another
letter. You can turn this function On or Off.
Accented Character Preview
Select if you want to type letters with accent
marks.
4. To access symbols and additional punctuation
marks, highlight the 123#& button on the
left, and then press the OK button.
5. To delete a character you entered, move the
highlight to the : button, and then press the
OK button.
6. To delete all the characters you entered,
move the highlight to the Clear button, and
then press the OK button.
7. When finished entering, move the highlight
to the Done button, and then press the OK
button.
✎✎ If you have a wireless keyboard connected
to your product, you can use the wireless
keyboard to enter letters, numbers, symbols,
and punctuation. Note that the wireless
keyboard will work only when the keyboard
popup appears and can only be used to enter
letters, numbers, symbols, and punctuation.
48 - English
Using the Settings Menu
100%
■■
The Settings menu contains functions that control
how the Browser operates and Browser security
functions. To open the Settings menu, highlight
the
icon in the Control Panel, and then press
the OK button. To select an option in the Settings
menu, highlight the option, and then press the
OK button.
http://www.samsung.com
100%
Enable Grabbing
Approved Sites
Private browsing on
Set Search Engine
Web Browser Settings
Help
Close
Manage Approved Sites : Lets you key in
URLs to add to the Approved Sites List and
delete sites from the Approved Sites list. If
you turn this function on and have not added
any sites to the Approved Sites list, you will
not be able to access any Internet sites.
Private browsing on/off
Enable or disable the Privacy mode. When the
Privacy mode is enabled, the browser does not
retain the URLs of sites you visit. If you want to
enable Privacy mode, select Yes.
If the Privacy mode is running, the “Stop” icon
appears in front of the URL at the top of the
screen. To disable Privacy mode, select it again
when Privacy mode is enabled.
Set Search Engine
You can set the desired Search Engine.
■■
Turns the Grabber function on and off. When
the Grabber function is on, you can move a
web page up and down without dragging the
scroll bar. The Grabber function is only available
in Pointer Browsing.
Approved Sites
■■
■■
■■
Lets you restrict your children’s access to
inappropriate web pages by allowing access
only to the web sites you have registered.
Every time you access this function, the PIN
screen appears. Press and hold the 123 button
until the Num pad appears on the screen. When
the Num pad appears, select a number using the
button and then press the OK button.
,.
The first time you access this function, enter
the default PIN, 0000.
You can change the PIN using the Reset
password for the Approved Sites function. See
below.
■■ Approved Sites feature : Turns the Approved
Sites function on or off.
■■ Reset password for Approved Sites : Change
the Approved Sites password.
■■ Add current site : Lets you add the currently
displayed web site to the Approved Sites list.
Set as homepage : You can set the Browser's
home page.
Pop-up Block : Turns the Pop-up Block on
and off.
Page Block : You can determine whether to
block advertisements and select the URLs for
which advertisements are blocked.
General : You can delete personal in
information such as website history and
browsing data (cookies, etc.), and reset
all web browser settings to their factory
defaults. You can also set the Security Mode.
✎✎ Set the Security Mode to On to avoid
■■
■■
■■
accessing malicious/phishing sites and
prevent malicious code from running.
Encoding : You can set the Encoding setting
for web pages to Automatic or select the
encoding format manually from a list.
Pointer : You can set the speed of the cursor
when the cursor is set to Pointer Browsing.
Browser Information : Displays the version
number and copyright information for the
Web Browser.
Help
Provides basic information about the operation
of the Web Browser.
49 - English
Network Services
Web Browser Settings
Enable/Disable Grabbing
Network Services
✎✎ Depending on the web site, some of the
Web Browser Settings functions may not be
activated. Functions that are not activated are
greyed out and cannot be used.
3. Select Network, and then press the OK
button.
4. Select BD-Live Settings, and then press the
OK button.
5. Select BD Data Management, and then press
the OK button.
Linking your Internet Service
Accounts to the Product
The Link Accounts function lets you link your
product to your accounts with Internet services
such as Pandora so that the product can log you
in to the service automatically when you start the
app for that service.
To create a service account link, follow these
steps:
1. On the Home screen, select the
button in
the upper right corner, and then press the OK
button to log in to your Samsung Account.
6. Select Select Device, and then press the OK
button.
7. Select USB device, and then press the OK
button.
8. Insert a Blu-ray Disc that supports BD-LIVE.
9. Select an item from the list of BD-LIVE service
contents provided by the disc manufacturer.
✎✎ The way you use BD-LIVE and the provided
contents may differ, depending on the disc
manufacturer.
2. After you have logged in, select the
button again, and then press the OK button.
3. Select Link Accounts in the My Account
screen, and then press the OK button.
4. On the Link Accounts screen, select the
service you want to link to the product, and
then press the OK button.
5. In the ID and Password screen, enter the ID
you use to log in to the service you selected
using the pop-up keyboard. When finished,
select Done, and then press the OK button.
6. Repeat the same process for the password.
When finished select Done, and then press
the OK button.
7. Select OK, and then press the OK button.
BD-LIVE™
Once the product is connected to your network,
you can enjoy various movie-related service
contents available on BD-LIVE compliant discs.
1. Attach a USB flash drive to the USB jack on
the front of the product, and then check
its remaining memory. The memory device
must have at least 1GB of free space to
accommodate the BD-LIVE services.
2. Select Settings on the Home screen, and
then press the OK button.
50 - English
Appendix
Additional Information
Digital Output
●●
Notes
●●
Connections
HDMI OUT
●●
●●
●●
●●
Certain HDMI output resolutions may not work,
depending on your TV.
You must have an HDMI connection to enjoy
videos with 3D technology.
A long HDMI cable may cause screen noise. If
this occurs, set HDMI Deep Colour to Off in the
menu.
Settings
●●
●●
●●
3D Settings
●●
TV Aspect Ratio
●●
●●
●●
●●
BD-Live Internet Connection
●●
Anynet+ (HDMI-CEC)
●●
●●
●●
Depending on the disc type, some aspect ratios
may not be available.
If you select an aspect ratio and option which is
different than the aspect ratio of your TV screen,
the picture might appear to be distorted.
If you select 16:9 Original, your TV may display
4:3 Pillarbox (black bars on the sides of the
picture).
●●
●●
When BD Wise is On, the Resolution setting
automatically defaults to BD Wise and BD Wise
appears in the Resolution menu.
If the product is connected to a device that does
not support BD Wise, you cannot use the BD
Wise function.
For proper operation of BD Wise, set the BD
Wise option in both the product and the TV to
On.
Depending on your TV, certain HDMI output
resolutions may not work. Please refer to the
user manual of your TV.
This function is not available if the HDMI cable
does not support CEC.
If your Samsung TV has an Anynet+ logo, then it
supports the Anynet+ function.
BD Data Management
●●
●●
BD Wise (Samsung Products only)
●●
The Internet connection may be restricted while
you are using BD-LIVE contents.
●●
●●
In the external memory mode, disc playback may
be stopped if you disconnect the USB device in
the middle of playback.
Only those USB devices formatted in the FAT file
system (DOS 8.3 volume label) are supported.
We recommend you use USB devices that
support the USB 2.0 protocol with 4 MB/sec or
faster read/write speeds.
The Resume Play function may not work after
you format the storage device.
The total memory available to BD Data
Management may differ, depending on
conditions.
DivX® Video On Demand
●●
For more information about DivX(R) VOD, visit
“http://vod.divx.com”.
51 - English
Appendix
●●
For some 3D discs, to stop a movie during 3D
playback, press the e (EXIT) button once. The
movie stops and the 3D mode option is deactivated.
To change a 3D option selection when you are
playing a 3D movie, press the e (EXIT) button
once. The Blu-ray menu appears. Press the e
(EXIT) button again, then select 3D Settings in
the Blu-ray menu.
Depending on the content and the position
of the picture on your TV screen, you may see
vertical black bars on the left side, right side, or
both sides.
Be sure to select the correct Digital Output or
you will hear no sound or just loud noise.
If the HDMI device (AV receiver, TV) is not
compatible with compressed formats (Dolby
Digital, DTS), the audio signal outputs as PCM.
Regular DVDs do not have BONUSVIEW audio
and Navigation Sound Effects.
Some Blu-ray Discs do not have BONUSVIEW
audio and Navigation Sound Effects.
This Digital Output setup does not affect the
analogue (L/R) audio or HDMI audio output to
your TV.
It affects the optical and HDMI audio output
when your product is connected to an AV
receiver.
If you play MPEG audio soundtracks, the audio
signal outputs as PCM regardless of your Digital
Output selections (PCM or Bitstream).
Digital Output can be activated when Sound
Output is set to TV Speaker.
Appendix
Front Display
●●
Playing JPEG files
●●
You cannot change the brightness of the
button and the VOL +, - button.
You can’t enlarge the subtitle and PG graphics in
the full screen mode.
Playing Content
Speaker Settings
●●
5V 0.5A
When Sound Output is set to TV Speaker, audio
is produced by the TV speakers.
●●
HDMI audio
●●
When HDMI audio is output to the TV speakers,
it is automatically down-mixed to 2 channels.
Audio Return Channel
●●
●●
●●
Using the TOOLS button while playing back
pictures
When Anynet+ (HDMI-CEC) is Off, the Audio
Return Channel function is not available.
Using an HDMI cable not certified for
ARC (Audio Return Channel) may cause a
compatibility problem.
The ARC function is only available if an ARCcompliant TV is connected.
Playback
●●
If the home cinema is connected to a BD Wise
compliant TV that has BD Wise On, the Picture
Settings menu will not appear.
The Background Music function will not work
unless the music file and the photo file are
located on the same storage media. Also, sound
quality can be impacted by the bitrate of the
MP3 music file, the size of the photos, and the
encoding method.
Disk and Format Compatibility
Disc types and content your Product
can Play
Playing Video files
●●
Video files with high bitrates of 20Mbps or more
strain the product’s capabilities and may stop
playing during playback.
Media
●●
●●
The ◄► indicator will not appear on the screen
if the BONUSVIEW section does not contain any
BONUSVIEW audio settings.
The languages available through the Audio
Language function depend on the languages
that are encoded on the disc. This function or
certain languages may not be available.
Some Blu-ray Discs may allow you to select
either the PCM or Dolby Digital audio English
soundtrack.
Selecting the Subtitle Language
●●
●●
●●
●●
●●
Depending on the Blu-ray Disc/DVD, you may be
able to change the subtitle language in the Disc
Menu. Press the DISC MENU button.
This function depends on the selection of
subtitles that are encoded on the disc and may
not be available on all Blu-ray Discs/DVDs.
Information about the main feature BONUSVIEW
mode will also appear if the Blu-ray Disc has a
BONUSVIEW section.
This function changes both the primary and
secondary subtitles at the same time.
The total number of primary and secondary
subtitles, respectively, is displayed.
Details
Blu-ray Disc BD-ROM or BD-RE/-R
disc recorded in the BD3D Blu-ray Disc RE format.
Selecting the Audio Language
●●
Disc Type
DVD-VIDEO,
DVD-RW,
DVD-R,
DVD+RW,
DVD+R,
VCD
DVD-VIDEO, recorded
DVD+RW/DVDRW(V)/DVD-R/+R
discs that have been
recorded and finalised,
or a USB storage media
containing DivX, MKV,
MP4, VCD contents.
MUSIC
CD-RW/-R,
DVD-RW/-R,
BD-RE/-R
Music recorded on CDRW/-R, DVD-RW/-R,
BD-RE/-R discs or a
USB storage media
containing MP3 or WMA
contents.
PHOTO
CD-RW/-R,
DVD-RW/-R,
BD-RE/-R
Photos recorded on
CD-RW/-R, DVDRW/-R, BD-RE/-R
discs or a USB storage
media containing JPEG
contents.
VIDEO
52 - English
✎✎ The product may not play certain CD-RW/-R and
DVD-R because of the disc type or recording
conditions.
✎✎ If a DVD-RW/-R disc has not been recorded
properly in DVD video format, it will not be
playable.
✎✎ Your product will not play content that has been
recorded on a DVD-R at a bitrate that exceeds 10
Mbps.
✎✎ Your product will not play content that has been
recorded on a BD-R or USB device at a bitrate that
exceeds 30 Mbps.
✎✎ Playback may not work for some types of discs, or
when you use specific operations, such as angle
change and aspect ratio adjustment. Information
about the discs is written in detail on the disc box.
Please refer to this if necessary.
✎✎ When you play a BD-J title, loading may take longer
than a normal title or some functions may perform
slowly.
Logos of Discs the Product can Play
Blu-ray Disc
3D Blu-ray Disc
BD-LIVE
Dolby
DTS
Disc Types your Product cannot Play
●●
●●
●●
HD DVD
DVD-ROM/PD/MV-Disc,
etc
DVD-RW(VR mode)
CVD/CD-ROM/CDV/
CD-G/CD-I/LD
(CD-Gs play audio only,
not graphics.)
●●
●●
●●
DVD-RAM
Super Audio CD
(except CD layer)
3.9 GB DVD-R Disc for
Authoring.
DivX
Appendix
●●
Java
PAL broadcast system in
U.K, France, Germany,
etc.
Region Code
✎✎ This product may not respond to all operating
commands because some Blu-ray Disc, DVD, and
CD discs allow specific or limited operation and
provide only certain features during playback.
Please note that this is not a defect in the
product.
✎✎ Samsung cannot guarantee that this product
will play every disc bearing the Blu-ray Disc,
DVD, or CD logo because disc formats evolve,
and problems and errors may occur during the
creation of Blu-ray Disc, DVD, and CD software
and/or the manufacture of discs.
✎✎ Please contact the SAMSUNG Customer Care
Centre at, if you have questions or encounter
difficulty when playing Blu-ray Disc, DVD, or CD
discs in this product. Also, refer to rest of this user
manual for additional information on playback
restrictions.
✎
✎ Some commercial discs and DVD discs purchased
outside your region may not play on this product.
Both products and discs are coded by region. These
regional codes must match for a disc to play. If the
codes do not match, the disc will not play.
The Region Number for this product is displayed on
the rear panel of the product.
Disc Type
Blu-ray
Disc
53 - English
Region
Code
Area
a
North America, Central
America, South America,
Korea, Japan, Taiwan, Hong
Kong and South East Asia.
b
Europe, Greenland, French
territories, Middle East, Africa,
Australia and New Zealand.
c
India, China, Russia, Central
and South Asia.
Appendix
1
The U.S., U.S. territories and
Canada
2
Europe, Japan, the Middle
East, Egypt, Africa, Greenland
3
Taiwan, Korea, the
Philippines, Indonesia, Hong
Kong
4
Mexico, South America,
Central America, Australia,
New Zealand, Pacific Islands,
Caribbean
5
Russia, Eastern Europe, India,
North Korea, Mongolia
6
China
DVDVIDEO
✎✎ Some DivX, MKV and MP4 format discs may not
play, depending on their video resolution and
frame rate.
Supported Formats
Notes on the USB connection
●●
●●
●●
●●
●●
●●
●●
●●
✎✎If the Region number of a Blu-ray Disc/DVD
does not correspond to the Region number of
this product, the product cannot play the disc.
AVCHD (Advanced Video Codec High
Definition)
●●
●●
●●
●●
●●
●●
This product can play back AVCHD format discs.
These discs are normally recorded and used in
camcorders.
The AVCHD format is a high definition digital video
camera format.
The MPEG-4 AVC/H.264 format compresses images
with greater efficiency than the conventional
image compressing format.
Some AVCHD discs use the “x.v.Colour” format.
This product can play back AVCHD discs that use
the “x.v.Colour” format.
“x.v.Colour” is a trademark of Sony Corporation.
“AVCHD” and the AVCHD logo are trademarks of
Matsushita Electronic Industrial Co., Ltd. and Sony
Corporation.
✎✎ Some AVCHD format discs may not play,
●●
●●
●●
●●
●●
●●
●●
●●
Your product supports USB storage media, MP3
players, digital cameras, and USB card readers.
The product does not support folder or file names
longer than 128 characters.
Some USB/digital camera devices may not be
compatible with the product.
Your product supports the FAT 16, FAT 32, and
NTFS file systems.
Connect USB devices directly to the product’s USB
port. Connecting through a USB cable may cause
compatibility problems.
Inserting more than one memory device into a
multi-card reader may cause the reader to operate
improperly.
The product does not support the PTP (Peer to
Peer) protocol.
Do not disconnect a USB device while it is
transferring or recording data.
The bigger the image resolution, the longer the
image takes to display.
This product cannot play MP3 files with DRM
(Digital Rights Management) downloaded from
commercial sites.
Your product only supports video that is under
30fps (frame rate).
Your product only supports USB Mass Storage Class
(MSC) devices such as thumb drives and USB HDD.
(HUB is not supported.)
Certain USB HDD Devices, multi-card readers and
thumb drives may not be compatible with this
product.
If some USB devices require excessive power, they
may be limited by the circuit safety device.
If playback from a USB HDD is unstable, provide
additional power by plugging the HDD into a wall
socket. If the problem continues, contact the USB
HDD manufacturer.
SAMSUNG is not responsible for any data file
damage or data loss.
depending on the recording conditions.
✎✎ AVCHD format discs need to be finalised.
✎✎ “x.v.Colour” offers a wider colour range than
normal DVD camcorder discs.
54 - English
Video File Support
File
Extension
Container
Video Codec
Resolution
Frame rate
(fps)
Bitrate
(Mbps)
24/25/30
60
Audio Codec
*.avi
*.mkv
*.asf
*.wmv
*.mp4
*.mov
*.3gp
*.vro
*.mpg
*.mpeg
*.ts
*.tp
*.trp
*.mov
*.flv
*.vob
*.svi
*.m2ts
*.mts
*.divx
*.ps
AVI
MKV
ASF
MP4
3GP
MOV
FLV
VRO
VOB
PS
TS
SVAF
*.webm
WebM
VP8
1920x1080
6~30
20
Vorbis
*.rmvb
RMVB
RV8/9/10 (RV30/40)
1920x1080
6~30
20
RealAudio 6
MVC
Motion JPEG
H.264 BP/MP/HP
Divx 3.11 / 4 / 5 / 6
MPEG4 SP/ASP
1920x1080
Window Media Video
v9(VC1)
FHD :
MAX 30
HD :
MAX 60
AVS
30
MPEG2
MPEG1
Microsoft MPEG-4 v3
Window Media Video
v7(WMV1), v8(WMV2)
H 263 Sorrenson
VP6
MAX 30
720x576
640x480
6~30
4
`` Limitations
`` Video decoder
-- Files are not supported if there are some issues
with contents among the supported codecs listed
above.
-- Normal playback is not guaranteed if the file's
container information is wrong or the file itself is
corrupted.
-- Sound or video play may cutoff for contents with
bitrate/frame rates that are above standard.
-- The seek (skip) function is not available if the file's
index table is damaged.
-- Depending on your network status, play may
become disrupted when playing contents from the
network.
-- Some USB/Digital camera devices may not be
compatible with the product.
-- RMVB format is supported in China, Hong Kong
and Southeast Asia.
-- AVS codec is supported for contents for China only
-- *.ps extension is supported for contents for China
only
-- DivX codec is not supported for contents in the US
-- Supports up to H.264 Level 4.1 (except for
FMO/ASO/RS)
-- Does not support VC1 AP L4
-- Except for WMV v7, v8, MSMPEG4 v3, MVC, VP6
Below 1280 X 720: 60 frame max
Above 1280 X 720: 30 frame max
-- Does not support GMC 2 or higher
-- Supports SVAF Top/Bottom, Side by Side, Left/Right
view sequence type(2 ES) Only
-- Supports BD MVC Spec Only
`` Audio decoder
---------
Supports WMA 10 Pro (Up to 5.1)
Does not support WMA lossless audio.
Supports M2 profile
ReadlAudio 10 lossless is not supported for
contents for China and Hong Kong
Does not support QCELP, AMR NB/WB
vorbis : Supported up to 5.1 channel
DD+ : Supported up to 7.1ch
DTS LBR codec is supported in MKV/MP4/TS
containers only
55 - English
Appendix
Microsoft MPEG-4 v1, v2
1280x720
AC3
LPCM
ADPCM
(IMA, MS)
AAC
HE-AAC
WMA
DD+
MPEG(MP3)
DTS
(Core, LBR)
Appendix
Music File Support
File Extension
Type
Codec
Comments
*.mp3
MPEG
MPEG1 Audio Layer 3
-
*.m4a
*.mpa
*.aac
MPEG4
AAC
-
*.flac
FLAC
FLAC
Supports up to 2ch
*.ogg
OGG
Vorbis
Supports up to 2ch
*.wma
WMA
WMA
Supports WMA 10 Pro (Up to 5.1)
Does not support WMA lossless
audio
Supports up to M2 profile
*.wav
wav
wav
-
*.mid
*.midi
midi
midi
type 0 and type 1
Seek not supported
Supported on USB only
*.ape
ape
ape
NonSmart not supported
*.aif
*.aiff
AIFF
AIFF
-
*.m4a
ALAC
ALAC
-
Picture File Support
File Extension
Type
Resolution
Comments
*.jpg
*.jpeg
JPEG
15360x8640
-
*.png
PNG
4096x4096
-
*.bmp
BMP
4096x4096
-
*.mpo
MPO
15360x8640
-
56 - English
Digital Output Selections
Setup
PCM
Connection
Audio
Stream on
Blu-ray Disc
Bitstream
(Unprocessed)
Up to PCM 7.1ch
PCM
Dolby
Digital
Up to PCM 5.1ch
Dolby Digital
Dolby
Digital Plus
Dolby Digital Plus
Dolby
TrueHD
Dolby TrueHD
DTSHD High
Resolution
Audio
HT-J7500W :
Up to PCM 5.1ch
HT-J7750W :
Up to PCM 7.1ch
■■
Re-encoded
Dolby Digital *
DTS-HD High
Resolution Audio
DTS-HD Master
Audio
PCM
Definition
for Blu-ray
Disc
DTS re-encoded
DTS
Appendix
DTS-HD
Master
Audio
Audio
Stream on
DVD
Bitstream
(Re-encoded
Dolby D)
HDMI supported AV receiver
PCM
DTS
Bitstream
(Re-encoded DTS)
PCM 2ch
Dolby
Digital
Up to PCM 5.1ch
Dolby Digital
DTS
HT-J7500W :
Up to PCM 5.1ch
HT-J7750W :
Up to PCM 7.1ch
DTS
Any
Decodes the main
Decodes the main
Outputs only the
feature audio
feature audio
Decodes the main main feature audio
and BONUSVIEW
and BONUSVIEW
feature audio
stream so that your
audio stream
audio stream
and BONUSVIEW
AV receiver can
together into PCM
together into PCM
audio stream
decode the audio
audio and adds
audio and adds
together into PCM
bitstream.
Navigation Sound
Navigation Sound
audio and adds
You will not hear
Effects, then reEffects, then reNavigation Sound BONUSVIEW audio
encodes the PCM
encodes the PCM
Effects.
or Navigation
audio into Dolby
audio into DTS
Sound Effects.
Digital bitstream or
bitstream.
PCM.
If the Source Stream is 2ch or mono, “Re-encoded Dolby D” Setting are not applied. Output will be PCM 2ch.
Blu-ray Discs may include three audio streams :
-- Main Feature Audio : The audio soundtrack of the main feature.
-- BONUSVIEW audio : An additional soundtrack such as the director or actor’s commentary.
-- Navigation Sound Effects : When you choose some menu navigation options, Navigation Sound Effects may
sound. Navigation Sound Effects are different on each Blu-ray Disc.
57 - English
Appendix
Resolution according to the content type
Content Type
Setup
BD Wise
Auto
Movie Frame :
Auto
Blu-ray Disc
E-contents/
Digital contents
Resolution of Blu-ray Disc
1080p@60F
UHD Output : Auto
2160p@24F
2160p@24F
UHD Output : Off
1080p@24F
1080p@24F
Movie Frame : Off
Max. Resolution of TV input Max. Resolution of TV input
Movie Frame : Auto (24 fps)
 1080p only
1080p@24F
1080p@24F
1080p
1080p@60F
1080p@60F
1080i
1080i
1080i
720p
720p
720p
576p/480p
576p/480p
576p/480p
Content Type
Setup
BD Wise
Auto
Movie Frame :
Auto
DVD
576i/480i
DVD 24fps
Conversion : Auto
UHD Output : Auto
UHD Output : Off
DVD 24fps Conversion : Off
Movie Frame : Off
2160p@24F
1080p@24F
Max. Resolution of TV input
Max. Resolution of TV input
Movie Frame : Auto (DVD 24fps Conversion : Auto)
 1080p only
1080p@24F
1080p
1080p@60F
1080i
1080i
720p
720p
576p/480p
576p/480p
✎✎ If the TV you connected to the product does not support Movie Frame or the resolution you selected, the
message "If no pictures are shown after selecting 'Yes', please wait for 15 seconds to return to the previous
resolution. Do you want to change the resolution?" appears. If you select Yes, the TV's screen will go to
blank for 15 seconds, and then the resolution will revert to the previous resolution automatically.
✎✎ If the screen stays blank after you have changed the resolution, remove all discs, and then press and hold
the @ button on the top of the product for more than 5 seconds. All settings are restored to the factory
default. Run the Initial Settings procedure again. Then, go to Settings > Picture > Resolution in the Menu,
and select the correct resolution for your TV.
✎✎ When you run the Initial Settings procedure, re-select the language and aspect ratio (screen size and format)
only. Resetting does not affect your network settings, so you should be able to skip Network Setup and
Software Update.
✎✎ When the factory default settings are restored, all stored user BD data will be deleted.
✎✎ The Blu-ray Disc must have the 24 frame feature for the product to use the Movie Frame (24fps) mode.
58 - English
Troubleshooting
Refer to the table below when this product does not function properly. If the problem you are experiencing is
not listed below or if the instructions below do not help, turn off the product, disconnect the power cord and
contact the nearest authorized dealer or Samsung Electronics Service Centre.
Symptom
You cannot eject the disc.
Check/Remedy
●●
●●
Playback does not start.
●●
●●
●●
Playback does not start
immediately when you
press the p button.
●●
No sound.
●●
●●
●●
●●
●●
HT-J7750W : You can only
hear sound from a few
speakers, but not all 8.
●●
HT-J7500W : Dolby Digital
5.1 CH Surround Sound is
not produced.
●●
●●
●●
●●
HT-J7750W : Dolby Digital
7.1 CH Surround Sound is
not produced.
●●
●●
The remote control does
not work.
●●
●●
●●
●●
The disc is rotating but
there is no picture.
Picture quality is poor
and the picture is
shaking.
Audio language and
subtitles do not work.
●●
●●
●●
●●
●●
Check the region number of the Blu-ray/DVD disc.
A Blu-ray/DVD disc purchased from abroad may not be playable.
CD-ROMs and DVD-ROMs cannot be played on this product.
Make sure that the rating level is correct.
Are you using a deformed disc or a disc with scratches on the surface?
Wipe the disc clean.
The home cinema does not play sound during fast playback, slow playback,
and step motion playback.
Are the speakers connected properly? Is the speaker setup correctly
customized?
Is the disc severely damaged?
On certain Blu-ray/DVD discs, sound is output from the front speakers only.
Check if the speakers are connected properly.
Adjust the volume.
When playing audio from a CD, the radio, or a TV, the unit outputs sound to
the front speakers only.
Is there "Dolby Digital 5.1 CH" mark on the disc? Dolby Digital 5.1 CH
Surround Sound is produced only if the disc is recorded with 5.1 channel
sound.
Is the audio language correctly set to Dolby Digital 5.1-CH in the information
display?
Is there "Dolby Digital 7.1 CH" marked on the disc? Dolby Digital 7.1 CH
Surround Sound is produced only if the disc is recorded with 7.1 channel
sound.
Is the audio language correctly set to Dolby Digital 7.1-CH in the information
display?
Are you operating the remote within its operational range and within the
proper angle relative to the sensor?
Are the batteries drained?
Is the TV power on?
Are the video cables connected properly?
Is the disc dirty or damaged?
A poorly manufactured disc may not be playable.
The Audio Language and subtitle functions will not work if the disc does not
contain them.
59 - English
Appendix
HT-J7500W : You can only
hear sound from a few
speakers, but not all 6.
Is the power cord plugged securely into the outlet?
Turn off the power, and then turn it back on.
Appendix
Symptom
Check/Remedy
The menu screen does not
appear even when you
select the menu function.
●●
The aspect ratio cannot be
changed.
●●
The product is not
working.
(Example: The power
goes off or you hear a
strange noise.)
The Product is not
working normally.
●●
●●
●●
You have forgotten the
rating level password.
●●
Can't receive radio
broadcasts.
●●
While listening to TV audio
through the product, there
is no sound.
●●
"Not Available" appears on
screen.
●●
If the HDMI output is set to
a resolution your TV cannot
support (for example,
1080p), you may not see a
picture on your TV.
●●
No HDMI output.
●●
●●
●●
Abnormal HDMI output
appears on the screen.
●●
Are you using a disc that does not contain menus?
The home cinema can play 16:9 Blu-ray/DVD discs in 16:9 Full mode, 4:3
Letter Box mode, or 4:3 Pan-Scan mode, but plays 4:3 Blu-ray/DVD discs
in 4:3 mode only. Refer to the Blu-ray Disc jacket, and then select the
appropriate aspect ratio.
Press and hold the remote control's e (EXIT) button for 5 seconds in
STANDBY mode. This will reset the unit.
-- Using the RESET function will erase all stored settings.
Do not use this function unless necessary.
With no disc in the product, press and hold the product's @ button for
longer than 5 seconds. INIT appears on the display and all settings will return
to their default values.
-- Using the RESET function will erase all stored settings.
Do not use this function unless necessary.
Is the antenna connected properly?
If the antenna's input signal is weak, install an external FM antenna in an
area with good reception.
If you press the OPEN/CLOSE ^ button while listening to TV audio using the
D. IN or AUX functions, the Blu-ray/DVD disc functions are turned on and
the TV audio is muted.
The feature is unavailable or the action cannot be completed at this time
because:
1. The Blu-ray/DVD disc's software restricts it.
2. The Blu-ray/DVD disc's software doesn’t support the feature (e.g., angles)
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of
range.
Press and hold the @ button on front panel for more than 5 seconds with no
disc in the product. All settings will revert to their factory settings.
Check the connection between the TV and the HDMI jack of the product.
Check if your TV supports 576p/480p/720p/1080i/1080p HDMI input
resolution.
If random noise appears on the screen, it means that TV does not support
HDCP (High-bandwidth Digital Content Protection).
60 - English
Symptom
Check/Remedy
BD-LIVE
The home cinema cannot
connect to the BD-LIVE
server.
●●
●●
●●
●●
●●
When using the BD-LIVE
service, an error occurs.
●●
Test whether the network connection is active by using the Network Status
function.
Check whether a USB memory device is connected to the product.
The memory device must have at least 1GB of free space to accommodate
the BD-LIVE service.
You can check the available size in BD Data Management. (See page 51)
See if the BD-Live Internet Connection option is set to Allow(All).
If all above fails, contact the content provider or update to the latest
firmware.
The USB memory device must have at least 1GB of free space to
accommodate the BD-LIVE service.
You can check the available size in BD Data Management. (See page 51)
✎✎ When the factory default settings are restored, all stored user BD data is deleted.
Appendix
Hereby, Samsung Electronics, declares that this equipment is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
The original Declaration of Conformity may be found at http://www.samsung.com, go to Support >
Search Product Support and enter the model name.
This equipment may be operated in all EU countries.
This equipment may only be used indoors.
61 - English
Appendix
Specifications
General
Weight
2.7 kg
Dimensions
430.0 (W) x 55.0 (H) x 312.0 (D) mm
Operating Temperature Range
+5°C to +35°C
Operating Humidity Range
10 % to 75 %
Signal/noise ratio
55 dB
FM Tuner Usable sensitivity
12 dB
HDMI
Total harmonic distortion
0.5 %
Video
2D : 2160p, 1080p, 1080i, 720p, 576p/480p
3D : 1080p, 720p
Audio
PCM multichannel audio, Bitstream audio, PCM audio
Front speaker output
165W x 2(3Ω)
Front Top speaker output
(HT-J7750W only)
165W x 2(3Ω)
Centre speaker output
170W(3Ω)
Surround speaker output
165W x 2(3Ω)
Amplifier Subwoofer speaker output
Frequency response
170W(3Ω)
Analogue input : 20Hz~20kHz (±3dB)
Digital input : 20Hz~40kHz (±4dB)
S/N Ratio
70dB
Channel separation
60dB
Input sensitivity
(AUX)500mV
62 - English
HT-J7500W
Speaker
system
Impedance
Frequency Output sound
range
pressure level
Front
Surround
3Ω
Centre
140Hz~
20kHz
20Hz ~
200Hz
Subwoofer
87dB/W/M
88dB/W/M
Rated Maximum
input
input
165W
330W
170W
340W
Dimensions
(W x H x D) (Unit : mm)
Weights
(Unit : kg)
95.0 x 280.0 x 101.0
1.75
95.0 x 150.0 x 101.0
0.64
320.0 x 80.5 x 101.0
1.02
200.0 x 390.0 x 350.0
5.70
Dimensions
(W x H x D) (Unit : mm)
Weights
(Unit : kg)
95.0 x 1215.0 x 101.0
(Stand base: 276.0 x 23.0
x 264.0)
5.01
95.0 x 1160.0 x 101.0
(Stand base: 276.0 x 23.0
x 264.0)
4.73
320.0 x 80.5 x 101.0
1.02
200.0 x 390.0 x 350.0
5.70
HT-J7750W
Speaker
system
Impedance
Frequency Output sound
range
pressure level
Rated Maximum
input
input
Front/
Front Top
Surround
3Ω
140Hz~
20kHz
87dB/W/M
165W
330W
Subwoofer
20Hz ~
200Hz
88dB/W/M
170W
340W
✎✎ Network speeds equal to or below 10Mbps are not supported.
✎✎ Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
✎✎ Weight and dimensions are approximate.
✎✎ Design and specifications are subject to change without prior notice.
✎✎ For the power supply and Power Consumption, refer to the label attached to the product.
ĞĞ SWA-7000
Weight
0.73 kg
Dimensions (W x H x D)
50.0 X 201.3 X 132.0 mm
Operating Temperature Range
+5°C to +35°C
Operating Humidity Range
10 % to 75 %
Output
165W x 2 CH
Frequency range
20Hz~20KHz
S/N Ratio
65dB
63 - English
Appendix
Centre
Appendix
Licences
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
For DTS patents, see http://patents.dts.com. Manufactured
under license from DTS Licencing Limited. DTS, DTS-HD,
the Symbol, DTS and the Symbol together, & DTS-HD and
the Symbol together are registered trademarks of DTS,
Inc. DTS-HD Master Audio | Essential and DTS Neo:Fusion II are trademarks of DTS, Inc. © DTS, Inc. All Rights
Reserved.
This DivX Certified® device has passed rigorous testing to ensure it plays DivX® video.
To play purchased DivX movies, first register your device at vod.divx.com. Find your
registration code in the DivX VOD section of your device setup menu.
DivX Certified® to play DivX® video up to HD 1080p, including premium content.
DivX®, DivX Certified® and associated logos are trademarks of DivX, LLC and are used under license.
Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668; 7,515,710; 7,519,274.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo
are trademarks or registered trademarks of HDMI Licencing LLC in the United States
and other countries.
Oracle and Java are registered trademarks of Oracle and/or its affiliates. Other names may be
trademarks of their respective owners.
This item incorporates copy protection technology that is protected by U.S. patents and other intellectual
property rights of Rovi Corporation. Reverse engineering and disassembly are prohibited.
Blu-ray Disc™, Blu-ray™, and the logos are trademarks of Blu-ray Disc Association.
This product uses Cinavia technology to limit the use of unauthorized copies of some commercially-produced
film and videos and their soundtracks. When a prohibited use of an unauthorized copy is detected, a message
will be displayed and playback or copying will be interrupted.
More information about Cinavia technology is provided at the Cinavia Online Consumer Information Centre at
http://www.cinavia.com. To request additional information about Cinavia by mail, send a postcard with your
mailing address to: Cinavia Consumer Information Centre, P.O. Box 86851, San Diego, CA, 92138, USA."
This product incorporates proprietary technology under license from Verance Corporation and is protected
by U.S. Patent 7,369,677 and other U.S. and worldwide patents issued and pending as well as copyright and
trade secret protection for certain aspects of such technology. Cinavia is a trademark of Verance Corporation.
Copyright 2004-2010 Verance Corporation. All rights reserved by Verance. Reverse engineering or disassembly
is prohibited.
- Open Source Licence Notice
In the case of using open source software, Open Source Licences are available on the product menu.
64 - English
UNITED
UNITED
UNITED
KINGDOM
KINGDOM
KINGDOM
EIRE
EIRE EIR
beyond
beyondthe
thecontrol
control
beyond
ofofSamsung.
the
Samsung.
control
This
his Samsung
SamsungThis
product
product
Samsung
isiswarranted
warranted
product
for
for
isthe
the
warranted
period
periodofof
fortwelve
twelve
the period
(12)
(12)months
of
months
twelve
from
from
(12)the
the
months
origiorigi- from the original
al date
dateofofpurchase,
purchase,
nal date
against
against
of purchase,
defective
defective
against
materials
materials
defective
and
andworkmanship.
materials
workmanship.
and In
workmanship.
Inthe
theevent
eventthat
that
In the event
that
6.6.This
Thiswarranty
warranty
6. is
This
isvalid
valid
warranty
for
forany
anyisperson
perso
valid
This
Samsung
product
is warranted
for
the
period
4.from
product
is notwhom
considered
to
defective
warranty
arranty service
service
warranty
isisrequired,
required,
service
you
you
isshould
should
required,
return
return
youthe
the
should
product
product
return
to
tothe
the
theretailer
product
retailer
from
toThis
the
whom
whom
retailer
itit from
it
possession
possession
ofofbe
possession
the
the
product
productof
during
during
the pro
the
th
of
twelve
(12)
months
from
the original
date
in
materials
nor workmanship
by
thatrights
was
as purchased.
purchased.
was
However,
However,
purchased.
Samsung
Samsung
However,
Authorised
Authorised
Samsung
Dealers
Dealers
Authorised
and
andAuthorised
Authorised
Dealers and
Service
Service
Authorised
Centres
Centres
Service
Centres
7.7.The
7. reason
Theconsumers
consumers
The
statutory
statutory
consumers
rightsstatuto
ininany
an
of
purchase,
against
defective
materials
and
itpurchasers
requires
order
to
conform
nnother
otherEC
ECCountries
Countries
in other
will
will
ECcomply
comply
Countries
with
with
will
the
the
comply
warranty
warranty
with
on
on
the
the
the
warranty
terms
termsissued
issued
on thetoto
terms
purchasers
issuedadaptation
into
in purchasers
in arising
the
theinretailer
retailer
arising
the retailer
from
fromthe
the
arising
purchase
purchase
from
he
hecountry
countryconcerned.
concerned.
the country
InIncase
concerned.
case
difficulty,
difficulty,
In case
details
details
ofwarranty
difficulty,
ofofour
ourAuthorised
Authorised
details of our
Service
Service
Authorised
Centres
Service
are
are
Centres
are Unless
warranty.
warranty.
Unless
warranty.
there
thereisisUnless
national
national
there
leg
leg
workmanship.
Inofof
the
event
that
service
toCentres
national
or local
technical
or
safety
available
vailable from:
from:is
available
from:
warranty
warranty
are
arethe
the
warranty
are the
consumers
consumers
sole
sole
consu
righ
righ
required,
you should return the product to the
standards in force in
any Country
other
than
tors
tors
shall
shallnot
not
be
be
tors
liable
liable
shall
for
for
not
indirect
indirect
be liable
ororcc
retailer from whom it was purchased. However,
the one for which the
product
was
originally
Samsung
Samsung
Electronics
Electronics
Samsung
U.K.
U.K.
Electronics
Ltd.
Ltd.Customer
Customer
U.K.
Ltd.
Care
Care
Customer
CentrePO
CentrePO
Care
Box
Box
CentrePO
479
479 and
Box
479compact
compactdiscs,
discs,
videos
videosoror
discs,
audio
audio
videos
taper
tapero
Samsung
Authorised
Dealers
and
Authorised
designed
manufactured.
This compact
warranty
GATESHEAD
GATESHEADGATESHEAD
NE9
NE99BJ
9BJUnited
United
NE9
Kingdom
Kingdom
9BJ United Kingdom
Service Centres in other EC Countries will
will not cover, and no re-imbursement
will beSAMSU
SAMSUNG
SAMSUNG
ELEC
ELEC
comply with
the
warranty
on
the
terms
issued
made for such adaptation nor any damage
United
UnitedKingdom
Kingdom
United Kingdom
to purchasers
in0330
theSAMSUNG
country
In case(7267864) which may result.
Tel
Tel: :0330
SAMSUNG
Tel : concerned.
0330
(7267864)
(7267864)
SAMSUNG
of difficulty,
details
of our
Authorised
Service
Fax:
Fax:
03307260001
03307260001
Fax:
03307260001
5. This warranty covers none of the following:
Centres are
available from:
www.samsung.com
www.samsung.com
www.samsung.com
a)Periodic check ups, maintenance and repair
or replacement of parts due to normal
wear and tear.
b)Cost relating to transport, removal or
installation of the product.
c)Misuse, including the faiure to use this
■WARRANTY
WARRANTY ■WARRANTY
CONDITIONS
CONDITIONSCONDITIONS
product for its normal purposes or
United Kingdom
1.
. The
1.isisThe
Thewarranty
warranty
only
onlywarranty
valid
validif,if,when
is
when
onlywarranty
warranty
valid if, service
when
service
warranty
isisrequired,
required,
service
the
theis
warranty
warranty
required,
card
card
theisis
warranty
fully
fully card is fully
incorrect installation.
Teland
: 0330
SAMSUNG
and
andproperly
properlycompleted
completed
and properly
and
is
completed
ispresented
presented
and
with
with
is(7267864)
the
presented
theoriginal
originalwith
invoice
invoice
the original
ororsales
salesinvoice
slip
slipororconfiror
confirsales slip or confirDamage caused by Lightning, Water, Fire,
mation,
mation,and
andthe
themation,
serial
serialwww.samsung.com/uk/support
number
number
and theon
on
serial
the
theproduct
number
producthas
on
hasthe
not
notproduct
been
beendefaced.
defaced.
has not been d)
defaced.
Acts of
God, War, Public
2.
. Samsung’s
Samsung’sobligations
2.
obligations
Samsung’s
are
areobligations
limited
limitedtotothe
the
arerepair
repair
limited
or,
or,
toatat
the
its
itsrepair
discretion,
discretion,
or, atreplacement
its
replacement
discretion,
ofofreplacement
of Disturbances,
the
theproduct
productororthe
thedefective
product
defective
part.
the defective part.
incorrect mains voltage, improper
EIRE orpart.
3.
. Warranty
Warrantyrepairs
repairs
3. Warranty
must
must
repairs
carried
carried
must
out
outbe
by
byAuthorised
carried
Authorised
out by
Samsung
Samsung
Authorised
Dealers
Dealers
Samsung
oror
Dealers
ventilation
or or
any other cause beyond the
Tel be
:be
0818
717100
Authorised
AuthorisedService
Service
Authorised
Centres.
Centres.
Service
No
Nore-imbursement
re-imbursement
Centres. No re-imbursement
will
willbe
bemade
madefor
for
willrepairs
repairs
be made
carried
carried
for of
repairs
carried
control
Samsung.
out
outby
bynon
nonSamsung
Samsung
out bywww.samsung.com/ie/support
non
Dealers
Dealers
Samsung
and,
and,any
Dealers
anysuch
suchand,
repair
repair
any
work
work
such
and
and
repair
damage
damage
worktoto
and
the
thedamage
prodprod- to the prod6.byThis
ucts
uctscaused
causedby
by
ucts
such
such
caused
repair
repairby
work
work
such
will
will
repair
not
notbe
be
work
covered
covered
will not
by
bybe
this
this
covered
warranty.
warranty.
this warranty
warranty.is valid for any person who
acquired possession
of the product
4.
. This
Thisproduct
product4.isisThis
not
notconsidered
product
considered
is not
totobe
considered
bedefective
defectiveto
ininbe
materials
materials
defective
nor
nor
inworkmanship
workmanship
materialslegally
norby
by
workmanship
by
WARRANTY
during
the
warranty
period.
reason
reasonthat
thatit■
itrequires
requires
reason that
adaptation
adaptation
itCONDITIONS
requires
ininorder
order
adaptation
totoconform
conform
in order
totonational
national
to conform
ororlocal
local
to national
technical
technical
or local
technical
ororsafety
safetystandards
standards
safety
inin
force
force
standards
ininany
Country
inCountry
force
other
other
any
than
Country
than
the
theone
other
onefor
for
than
which
which
one
theproduct
product
for which the
productrights in any
1. orThe
warranty
isany
only
valid in
if,
when
warranty
7.thethe
The
consumers
statutory
was
wasoriginally
originallydesigned
was
designed
originally
and
manufactured.
designed
manufactured.
manufactured.
This
Thiswarranty
warranty
will
This
willnot
not
warranty
cover,
cover,and
will
andno
not
norecover,
reand no reservice
isand
required,
theand
warranty
card is fully
applicable national legislation whether
imbursement
imbursementwill
will
imbursement
be
bemade
madefor
for
will
such
such
be made
adaptation
adaptation
for such
nor
adaptation
any
anydamage
damage
norwhich
which
any damage
may
mayresult.
result.
which may result.
and
properly
completed
and
isnor
presented
against the retailer arising from the purchase
5.
. This
Thiswarranty
warranty
5. covers
This
covers
warranty
none
none
ofof
covers
the
theinvoice
following:
following:
noneorofsales
the following:
with
the
original
slip or
contract
or parts
otherwise
are not affected by this
a)a)Periodic
Periodiccheck
check
a) Periodic
ups,
ups,maintenance
maintenance
check ups,and
maintenance
andrepair
repairororreplacement
and
replacement
repair orofof
replacement
parts
partsdue
duetotoof
due to
confirmation,
warranty. Unless there is national legislation
normal
normalwear
wearand
and
normal
tear.
tear.wear and
and the
tear.serial number on the
hasremoval
not
the contrary, the rights under this warranty
b)b)Cost
b)toproduct
Costrelating
relating
toCost
transport,
transport,
relating
removal
to been
transport,
orordefaced.
installation
installation
removalofof
orthe
the
installation
product.
product.of the to
product.
c)c)Misuse,
Misuse,including
including
Misuse,
the
thefaiure
faiure
including
totouse
use
the
this
this
faiure
product
to use
for
for
its
itsnormal
product
normal for its normal
are the consumers sole rights and Samsung,
obligations
areproduct
limited
tothis
the
2. c)Samsung’s
purposes
purposesororincorrect
incorrect
purposes
installation.
installation.
installation.
its subsidiaries and distributors shall not be
repair
or,
atoritsincorrect
discretion,
replacement of the
d)d)Damage
Damagecaused
caused
d) Damage
by
byLightning,
Lightning,
causedWater,
Water,
by Lightning,
Fire,
Fire,Acts
Acts
Water,
ofofGod,
God,
Fire,War,
War,
ActsPublic
Public
of God,
War,
liable
forPublic
indirect or consequential loss or any
product or the defective part.
Disturbances,
Disturbances,incorrect
Disturbances,
incorrectmains
mains
incorrect
voltage,
voltage,mains
improper
improper
voltage,
ventilation
ventilation
improper
ororany
any
ventilation
other
othercause
cause
orto
any
other cause
damage
records,
compact discs, videos or
3. Warranty repairs must be carried out by
audio taper or any other related equipment
-2-2-2Authorised Samsung Dealers or Authorised
or material.
Service Centres. No re-imbursement will be
made for repairs carried out by non Samsung
SAMSUNG ELECTRONICS (U.K.) LTD.
Dealers and, any such repair work and
damage to the products caused by such repair
work will not be covered by this warranty.
Eire
Eire
Eire U.K. Ltd
Samsung
Electronics
Tel
Tel: :0818
0818
717100
717100
Tel : 0818
717100
Samsung
Customer
Support
Centre
Fax:
Fax:+44
+44117
117
Fax:
915
6736
6736
+44 117
Selectapost
38,915
Sheffield,
S97915
3FJ 6736
www.samsung.com
www.samsung.com
www.samsung.com
United Kingdom
© 2015 Samsung Electronics Co., Ltd. All rights reserved.
Area
` Europe
AUSTRIA
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please
contact the SAMSUNG customer care centre.
Contact Centre 
0800 - SAMSUNG (0800 - 7267864)
Web Site
www.samsung.com/at/support
www.samsung.com/be/support
(Dutch)
BELGIUM
02-201-24-18
www.samsung.com/be_fr/support (French)
BOSNIA
051 331 999
www.samsung.com/support
BULGARIA 07001 33 11 , sharing cost
www.samsung.com/bg/support
CROATIA
062 726 786
www.samsung.com/hr/support
800 - SAMSUNG (800-726786)
www.samsung.com/cz/support
CZECH
Samsung Electronics Czech and Slovak, s.r.o. V Parku 2343/24, 148 00 Praha 4
DENMARK 70 70 19 70
www.samsung.com/dk/support
Finland
030-6227 515
www.samsung.com/fi/support
FRANCE
01 48 63 00 00
www.samsung.com/fr/support
0180 6 SAMSUNG bzw.
0180 6 7267864*
GERMANY 0180 6 67267864*
www.samsung.com/de/support
(*0,20 €/Anruf aus dem dt. Festnetz, aus
dem Mobilfunk max. 0,60 €/Anruf)
CYPRUS
8009 4000 only from landline, toll free
80111-SAMSUNG (80111 726 7864) only
www.samsung.com/gr/support
from land line
GREECE
(+30) 210 6897691 from mobile and land
line
0680SAMSUNG (0680-726-786)
http://www.samsung.com/hu/
HUNGARY
0680PREMIUM (0680-773-648)
support
ITALIA
800-SAMSUNG (800.7267864)
www.samsung.com/it/support
LUXEMBURG 261 03 710
www.samsung.com/support
Area
MONTENEGRO
SLOVENIA
NETHERLANDS
NORWAY
POLAND
PORTUGAL
ROMANIA
SERBIA
SLOVAKIA
SPAIN
SWEDEN
Contact Centre 
020 405 888
Web Site
080 697 267
090 726 786
0900-SAMSUNG (0900-7267864) (€ 0,10/
Min)
815 56480
0 801-172-678* lub +48 22 607-93-33 **
*(całkowity koszt połączenia jak za 1 impuls
według taryfy operatora)
** (koszt połączenia według taryfy operatora)
808 20 7267
08008 SAMSUNG (08008 726 7864)
TOLL FREE No.
011 321 6899
0800 - SAMSUNG(0800-726 786)
0034902172678
0771 726 7864 (SAMSUNG)
Switzerland
0848 726 78 64 (0848-SAMSUNG)
U.k
EIRE
LITHUANIA
Latvia
ESTONIA
0330 SAMSUNG (7267864)
0818 717100
8-800-77777
8000-7267
800-7267
www.samsung.com/support
www.samsung.com/si/support
www.samsung.com/nl/support
www.samsung.com/no/support
www.samsung.com/pl/support
www.samsung.com/pt/support
www.samsung.com/ro/support
www.samsung.com/rs/support
www.samsung.com/sk/support
www.samsung.com/es/support
www.samsung.com/se/support
www.samsung.com/ch/support
(German)
www.samsung.com/ch_fr/support (French)
www.samsung.com/uk/support
www.samsung.com/ie/support
www.samsung.com/lt/support
www.samsung.com/lv/support
www.samsung.com/ee/support
Correct disposal of batteries in this product
(Applicable in countries with separate collection systems)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be
disposed of with other household waste at the end of their working life. Where marked, the chemical symbols
Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC
Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health
or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste
and recycle them through your local, free battery return system.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their
working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle them responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
AH68-02806A-00
AH68-02806A-00