EN
User Manual
Cooker
ZCK68300B
ZCK68300W
ZCK68300X
GB
IE
Contents
Safety information
Safety instructions
Product description
Before first use
Hob - Daily use
Hob - Hints and tips
Hob - Care and cleaning
2
3
6
7
8
9
9
Oven - Daily use
Oven - Clock functions
Oven - Hints and tips
Oven - Care and cleaning
Troubleshooting
Installation
Energy efficiency
10
11
13
18
20
21
24
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an
incorrect installation and use causes injuries and damages.
Always keep the instructions with the appliance for future
reference.
Children and vulnerable people safety
WARNING!
Risk of suffocation, injury or permanent disability.
•
•
•
•
•
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Do not let children play with the appliance.
Keep all packaging away from children.
Keep children and pets away from the appliance when it
operates or when it cools down. Accessible parts are hot.
Cleaning and user maintenance shall not be made by children
without supervision.
General Safety
•
•
2
Only a qualified person must install this appliance and replace
the cable.
Do not operate the appliance by means of an external timer or
separate remote-control system.
www.zanussi.com
•
•
•
•
•
•
•
•
•
•
•
•
Unattended cooking on a hob with fat or oil can be dangerous
and may result in fire.
Never try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire blanket.
Do not store items on the cooking surfaces.
Do not use a steam cleaner to clean the appliance.
Metallic objects such as knives, forks, spoons and lids should
not be placed on the hob surface since they can get hot.
Remove any spillage from the lid before opening. Let the hob
surface cool down before closing the lid.
Internally the appliance becomes hot when in operation. Do not
touch the heating elements that are in the appliance. Always
use oven gloves to remove or put in accessories or ovenware.
Before maintenance cut the power supply.
Ensure that the appliance is switched off before replacing the
lamp to avoid the possibility of electric shock.
Do not use harsh abrasive cleaners or sharp metal scrapers to
clean the glass door since they can scratch the surface, which
may result in shattering of the glass.
If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
The means for disconnection must be incorporated in the fixed
wiring in accordance with the wiring rules.
Safety instructions
This appliance is suitable for the following
markets: GB IE
Installation
WARNING!
•
•
•
•
•
•
•
•
Only a qualified person must install
this appliance.
•
Remove all the packaging.
Do not install or use a damaged appliance.
Obey the installation instruction supplied
with the appliance.
Always be careful when you move the
appliance because it is heavy. Always wear
safety gloves.
Do not pull the appliance by the handle.
•
www.zanussi.com
•
•
The kitchen cabinet and the recess must
have suitable dimensions.
Keep the minimum distance from the other
appliances and units.
Make sure that the appliance is installed
below and adjacent safe structures.
Parts of the appliance carry current. Close
the appliance with furniture to prevent
touching the dangerous parts.
The sides of the appliance must stay
adjacent to appliances or to units with the
same height.
Do not install the appliance on a platform.
Do not install the appliance adjacent to a
door or under a window. This prevents hot
cookware to fall from the appliance when the
door or the window is opened.
3
•
Make sure to install a stabilizing means in
order to prevent tipping of the appliance.
Refer to Installation chapter.
•
•
Electrical Connection
WARNING!
Risk of fire and electrical shock.
•
•
•
•
•
•
•
•
•
•
•
•
•
All electrical connections should be made by
a qualified electrician.
The appliance must be earthed.
Make sure that the electrical information on
the rating plate agrees with the power
supply. If not, contact an electrician.
Always use a correctly installed shockproof
socket.
Do not use multi-plug adapters and
extension cables.
Do not let mains cables touch or come near
the appliance door, especially when the door
is hot.
The shock protection of live and insulated
parts must be fastened in such a way that it
cannot be removed without tools.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after
the installation.
If the mains socket is loose, do not connect
the mains plug.
Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
Use only correct isolation devices: line
protecting cut-outs, fuses (screw type fuses
removed from the holder), earth leakage trips
and contactors.
The electrical installation must have an
isolation device which lets you disconnect
the appliance from the mains at all poles.
The isolation device must have a contact
opening width of minimum 3 mm.
Fully close the appliance door, before you
connect the mains plug to the mains socket.
Gas connection
•
•
•
4
All gas connections should be made by a
qualified person.
Before installation, make sure that the local
distribution conditions (nature of the gas and
gas pressure) and the adjustment of the
appliance are compatible.
Make sure that there is air circulation around
the appliance.
The information about the gas supply is on
the rating plate.
This appliance is not connected to a device,
which evacuates the products of
combustion. Make sure to connect the
appliance according to current installation
regulations. Pay attention to requirements
regarding adequate ventilation.
Use
WARNING!
Risk of injury and burns.
Risk of electrical shock.
•
•
•
•
•
•
•
•
Use this appliance in a household only.
Do not change the specification of this
appliance.
Make sure that the ventilation openings are
not blocked.
Do not let the appliance stay unattended
during operation.
Deactivate the appliance after each use.
Be careful when you open the appliance
door while the appliance is in operation. Hot
air can release.
Do not operate the appliance with wet hands
or when it has contact with water.
Do not use the appliance as a work surface
or as a storage surface.
WARNING!
Risk of fire and explosion
•
•
•
•
•
•
Fats and oil when heated can release
flammable vapours. Keep flames or heated
objects away from fats and oils when you
cook with them.
The vapours that very hot oil releases can
cause spontaneous combustion.
Used oil, that can contain food remnants,
can cause fire at a lower temperature than
oil used for the first time.
Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
Do not let sparks or open flames to come in
contact with the appliance when you open
the door.
Open the appliance door carefully. The use
of ingredients with alcohol can cause a
mixture of alcohol and air.
WARNING!
Risk of damage to the appliance.
•
To prevent damage or discoloration to the
enamel:
www.zanussi.com
•
•
•
•
•
•
•
•
•
•
•
•
•
•
– do not put ovenware or other objects in
the appliance directly on the bottom.
– do not put water directly into the hot
appliance.
– do not keep moist dishes and food in the
appliance after you finish the cooking.
– be careful when you remove or install
the accessories.
Discoloration of the enamel has no effect on
the performance of the appliance. It is not a
defect in the sense of the warranty law.
Use a deep pan for moist cakes. Fruit juices
cause stains that can be permanent.
Do not keep hot cookware on the control
panel.
Do not let cookware boil dry.
Be careful not to let objects or cookware fall
on the appliance. The surface can be
damaged.
Do not activate the cooking zones with
empty cookware or without cookware.
Do not put aluminium foil on the appliance or
directly on the bottom of the appliance.
Cookware made of cast iron, aluminium or
with a damaged bottom can cause
scratches. Always lift these objects up when
you have to move them on the cooking
surface.
Provide good ventilation in the room where
the appliance is installed.
Use only stable cookware with the correct
shape and diameter larger than the
dimensions of the burners.
Make sure the flame does not go out when
you quickly turn the knob from the maximum
to the minimum position.
Use only the accessories supplied with the
appliance.
Do not install a flame diffuser on the burner.
This appliance is for cooking purposes only.
It must not be used for other purposes, for
example room heating.
•
•
•
•
•
•
•
•
Lid
•
•
•
•
•
•
Risk of injury, fire, or damage to the
appliance.
•
•
Before maintenance, deactivate the
appliance.
Disconnect the mains plug from the mains
socket.
Make sure the appliance is cold. There is the
risk that the glass panels can break.
www.zanussi.com
Do not change the specification of the lid.
Clean the lid regularly.
Do not open the lid, when there are spills on
the surface.
Before you close the lid turn all burners off.
Do not close the lid until the hob and oven
are completely cold.
Glass lid can shatter, when heated (if
applicable).
Internal light
•
The type of light bulb or halogen lamp used
for this appliance is only for household
appliances. Do not use it for house lighting.
WARNING!
Risk of electrical shock.
Care and Cleaning
WARNING!
Replace immediately the door glass panels
when they are damaged. Contact the
Authorised Service Centre.
Be careful when you remove the door from
the appliance. The door is heavy!
Clean regularly the appliance to prevent the
deterioration of the surface material.
Remaining fat or food in the appliance can
cause fire.
Clean the appliance with a moist soft cloth.
Only use neutral detergents. Do not use
abrasive products, abrasive cleaning pads,
solvents or metal objects.
If you use an oven spray, obey the safety
instructions on the packaging.
Do not clean the catalytic enamel (if
applicable) with any kind of detergent.
Do not clean the burners in the dishwasher.
•
•
Before replacing the lamp, disconnect the
appliance from the power supply.
Only use lamps with the same specifications.
Disposal
WARNING!
Risk of injury or suffocation.
•
Contact your municipal authority for
information on how to discard the appliance
correctly.
5
•
•
•
•
Disconnect the appliance from the mains
supply.
Cut off the mains cable and discard it.
Remove the door catch to prevent children
and pets to get closed in the appliance.
Flat the external gas pipes.
Service
•
•
To repair the appliance contact an
Authorised Service Centre.
Use original spare parts only.
Product description
General overview
1
2
3
6
3
2
1
4
5
4
3
2
1
1
2
3
4
5
6
Control panel and hob
Air vents for the cooling fan
Heating element
Lamp
Fan
Shelf positions
4
5
Cooking surface layout
1
6
5
2
4
3
1 Steam outlet - number and position depend
on the model
2 Semi-rapid burner
3 Auxiliary burner
4 Rapid burner
5 Semi-rapid burner
www.zanussi.com
Cooker control panel
1
2
3
6
4
1
5
Accessories
•
•
Wire shelf
For cookware, cake tins, roasts.
Grill- / Roasting pan
To bake and roast or as pan to collect fat.
Knobs for the hob
Knob for the main oven functions
Electronic programmer
Knob for the top oven functions
Temperature lamp / symbol / indicator for
the top oven
6 Temperature lamp / symbol / indicator for
the main oven
1
2
3
4
5
•
Trivet
For roasting and grilling.
Use the trivet only with the Grill- /
roasting pan.
Before first use
WARNING!
Refer to Safety chapters.
Initial Cleaning
Remove all accessories from the appliance.
Refer to "Care and cleaning"
chapter.
Changing the time
You cannot change the time of day if
the Duration
operates.
or End
function
Press
again and again until the indicator for
the Time of Day function flashes.
To set a new time, refer to "Setting the time".
Clean the appliance before first use.
Put the accessories back to their initial position.
Preheating
Setting the time
Preheat the empty appliance to burn off the
remaining grease.
You must set the time before you operate the
oven.
Only the top oven works without the
set time.
The indicator for the Time of day function
flashes when you connect the appliance to the
electrical supply, when there was a power cut
or when the timer is not set.
Press the
or
button to set the correct
time.
After approximately five seconds, the flashing
stops and the display shows the time of day you
set.
www.zanussi.com
Preheat the two ovens. Heat up one
oven at a time.
1. Set the maximum temperature.
2. Let the appliance operate for 1 hour.
3. Set the function .
4. Let the appliance operate for 15 minutes.
Accessories can become hotter than usual. The
appliance can emit an odour and smoke. This is
normal. Make sure that the airflow is sufficient.
7
Hob - Daily use
WARNING!
The spark generator can start
automatically when you switch on
the mains, after installation or a
power cut. It is normal.
Refer to Safety chapters.
Ignition of the hob burners
Always light the burner before you
put on the cookware.
Burner overview
WARNING!
Be very careful when you use open
fire in the kitchen environment. The
manufacturer declines any
responsibility in case of the flame
misuse.
A
B
I
1. Turn the knob for the hob to the position
and push it down. When you push the knob,
the spark generator activates automatically.
2. Keep the knob for the hob pushed for equal
or less than 10 seconds to let the
thermocouple warm up. If not, the gas
supply is interrupted.
3. Adjust the flame after it is regular.
H
C
D
G
E
F
WARNING!
Do not keep the knob pushed for
more than 15 seconds. If the burner
does not light after 15 seconds,
release the knob, turn it into the off
position and try to light the burner
again after minimum 1 minute.
If after some tries the burner does
not light, check if the crown and its
cap are in the correct position.
In the absence of electricity you can
ignite the burner without an
electrical device. In this case
approach the burner with a flame,
push the relevant knob down and
turn it to maximum position. Keep
the knob pushed for equal or less
than 10 seconds to let the
thermocouple warm up.
If the burner accidentally goes out,
turn the knob to the off position and
try to light the burner again after
minimum 1 minute.
8
A)
B)
C)
D)
E)
F)
G)
H)
I)
Burner cap
Burner crown
Ignition candle
Thermocouple
Hob
Slots
Burner body
Location peg
Hole
Replacing burner parts
1. Put carefully the burner crown on the burner
body. Let the crown fall freely onto the
body. Do not use force.
Make sure that the hole in the crown is
above the ignition candle.
Make sure that the location pegs are in the
slots in the burner body.
Make sure that you can move the crown a
small distance from side to side.
2. Put the burner cap centrally on top of the
crown (enamel side up).
Make sure that the cap is correctly installed
and you can move the cap from side to side
and front to back.
3. Try to light the burner.
www.zanussi.com
If the burner does not ignite, adjust the crown
and cap again.
Turning the burner off
To put the flame out, turn the knob to the off
position
Lid Safety Device
Lid has safety device, which cuts off the gas
supply for the hob. It works only when the lid is
closed.
WARNING!
.
Always use the knob for the hob to
switch off a burner. Do not use the
lid as a cut-off device.
WARNING!
Always turn the flame down or
switch it off before you remove the
pans from the burner.
Hob - Hints and tips
WARNING!
Diameters of cookware
Refer to Safety chapters.
WARNING!
Use cookware with diameters
applicable to the size of burners.
Cookware
WARNING!
Do not put the same pan on two
burners.
WARNING!
Do not put unstable or damaged
pots on the burner to prevent from
spill and injury.
CAUTION!
Burner
Diameter of cookware (mm)
Rapid
180 - 260
Semi-rapid
120 - 220
Auxiliary
80 - 160
Make sure that pot handles are not
above the front edge of the cooktop.
CAUTION!
Make sure that the pots are placed
centrally on the burner in order to
get maximum stability and to get
lower gas consumption.
Hob - Care and cleaning
WARNING!
Refer to Safety chapters.
General information
•
•
•
•
•
Clean the hob after each use.
Always use cookware with clean bottom.
Scratches or dark stains on the surface have
no effect on how the hob operates.
Use a special cleaner applicable for the
surface of the hob.
Wash stainless steel parts with water, and
then dry them with a soft cloth.
www.zanussi.com
Pan supports
The pan supports are not resistant
to washing in a dishwasher. They
must be washed by hand.
1. Remove the pan supports to easily clean
the hob.
Be very careful when you
replace the pan supports to
prevent the hob top from
damage.
2. The enamel coating occasionally can have
rough edges, so be careful when you wash
9
the pan supports by hand and dry them. If
necessary, remove stubborn stains with a
paste cleaner.
3. After you clean the pan supports, make sure
that they are in correct positions.
4. For the burner to operate correctly, make
sure that the arms of the pan supports are
aligned with the centre of the burner.
Cleaning the hob
•
Remove immediately: melted plastic,
plastic foil, and food with sugar. If not, the
dirt can cause damage to the hob.
•
Remove when the hob is sufficiently
cool: limescale rings, water rings, fat stains,
shiny metallic discoloration. Clean the hob
with a moist cloth and some detergent. After
cleaning, rub the hob dry with a soft cloth.
Cleaning the spark plug
This feature is obtained through a ceramic
ignition candle with a metal electrode. Keep
these components well clean to prevent difficult
lighting and check that the burner crown holes
are not obstructed.
Oven - Daily use
WARNING!
Refer to Safety chapters.
Activating and deactivating the top /
main oven
1. Turn the knob for the top / main oven
functions to select an oven function.
2. To deactivate the oven turn the knob for the
top / main oven functions to the off position.
It depends on the model if your
appliance has knob symbols,
indicators or lamps:
• The indicator comes on when the
oven heats up.
• The lamp comes on when the
oven operates.
• The symbol shows whether the
knob controls one of the cooking
zones, the oven functions or the
temperature.
Top oven functions
Symbol
100 - 250
10
Oven function
Application
Off position
The appliance is off.
Oven Lamp
To activate the lamp without a cooking function.
Conventional Cooking
To bake and roast food on 1 shelf position.
Dual Circuit Grill
To grill food items in medium quantities in the middle of the
shelf. To make toasts.
Full Grill
To grill flat food and to toast bread.
www.zanussi.com
Main oven functions
Symbol
100 - 250
Oven function
Application
Off position
The appliance is off.
Oven Lamp
To activate the lamp without a cooking function.
Defrost
To defrost frozen food.
Thermaflow®
To bake on up to 2 shelf positions at the same time and to
dry food. Set the temperature 20 - 40 °C lower than for
Conventional Cooking.
Cooling fan
When the appliance operates, the cooling fan
activates automatically to keep the surfaces of
the appliance cool. If you deactivate the
appliance, the cooling fan can continue to
operate until the appliance cools down.
2. Put the deep pan into the oven on the
necessary shelf position.
You can use the trivet to grill flat dishes in large
quantities and to toast.
1. Put the trivet into the deep pan so that the
supports of the wire shelf point down.
Trivet and Grill- / Roasting pan
WARNING!
Be careful when you remove the
accessories from a hot appliance.
There is a risk of burns.
You can use the trivet to roast larger pieces of
meat or poultry on one shelf position.
1. Put the trivet into the deep pan so that the
supports of the wire shelf point up.
2. Put the deep pan into the oven on the
necessary shelf position.
Oven - Clock functions
Display
The electronic programmer works
only with the main oven.
www.zanussi.com
11
A
B
A) Function indicators
B) Time display
C) Function indicator
C
Buttons
Button
Function
Description
MINUS
To set the time.
CLOCK
To set a clock function.
PLUS
To set the time.
Clock functions table
Clock function
Application
Time of day
To set, change or check the time of day.
Minute Minder
To set countdown time. This function has no effect on the operation of
the appliance.
Duration
To set the cooking time of the oven.
End
To set the time of day when the oven should deactivate.
You can use the functions Duration
and End
at the same time to
set the time for how long the
appliance should operate and when
the appliance should deactivate.
This lets you activate the appliance
with a delay in time. First set the
Duration
and then the End
.
Setting the clock functions
For Duration
and End
, set an oven
function and temperature of cooking. This is not
necessary for the Minute Minder
.
1. Press
again and again until the indicator
for the necessary clock function starts to
flash.
12
2. Press
or
to set the time for the
necessary clock function.
The clock function operates. The display shows
the indicator for the clock function you set.
For the Minute Minder function the
display shows the time left.
3. When the time ends the indicator of the
clock function flashes and an acoustic
signal sounds. Press a button to stop the
signal.
4. Turn the knob for the oven functions and
the knob for the temperature to the off
position.
With the Duration
and End
functions, the appliance deactivates
automatically.
The functions work only for the main
oven.
www.zanussi.com
Cancelling the clock functions
2. Press and hold .
The clock function goes out after some
seconds.
1. Press the
again and again until the
necessary function indicator flashes.
Oven - Hints and tips
WARNING!
Refer to Safety chapters.
The temperature and baking times in
the tables are guidelines only. They
depend on the recipes and the
quality and quantity of the
ingredients used.
Top oven
The top oven is the smaller of the two ovens. It
has 3 shelf positions. Use it to cook smaller
quantities of food. It gives especially good
results when used to cook fruitcakes, sweets
and savoury flants or quiche.
Main oven
The main oven is particularly suitable for
cooking larger quantities of food.
Baking
•
settings (temperature, cooking times) and
shelf positions to the values in the tables.
• The manufacturer recommends that you use
the lower temperature the first time.
• If you cannot find the settings for a special
recipe, look for the one that is almost the
same.
• You can extend baking times by 10 – 15
minutes if you bake cakes on more than one
shelf position.
• Cakes and pastries at different heights do
not always brown equally at first. If this
occurs, do not change the temperature
setting. The differences equalize during the
baking procedure.
• With longer baking times, you can deactivate
the oven approximately 10 minutes before
the end of the baking time and then use the
residual heat.
When you cook frozen food, the trays in the
oven can twist during baking. When the trays
become cold again, the distortions are gone.
Your oven can bake or roast differently to the
appliance you had before. Adapt your usual
Tips on baking
Baking results
Possible cause
Remedy
The bottom of the cake is not
browned sufficiently.
The shelf position is incorrect.
The cake sinks and becomes
soggy, lumpy or streaky.
The oven temperature is too high. The next time you bake, set a
slightly lower oven temperature.
The cake sinks and becomes
soggy, lumpy or streaky.
The baking time is too short.
Set a longer baking time. You
cannot decrease baking
times by setting higher temperatures.
The cake sinks and becomes
soggy, lumpy or streaky.
There is too much liquid in the
mixture.
Use less liquid. Be careful with
mixing times, especially if you use
a mixing machine.
The cake is too dry.
The oven temperature is too low.
The next time you bake, set a
higher oven temperature.
www.zanussi.com
Put the cake on a lower shelf.
13
Baking results
Possible cause
Remedy
The cake is too dry.
The baking time is too long.
The next time you bake, set a
shorter baking time.
The cake browns unevenly.
The oven temperature is too high
and the baking time is too short.
Set a lower oven temperature
and a longer baking time.
The cake browns unevenly.
The mixture is unevenly distributed.
Spread the mixture evenly on the
baking tray.
The cake is not ready in the baking time given.
The oven temperature is too low.
The next time you bake, set a
slightly higher oven temperature.
Conventional Baking - Top Oven
Food
Temperature (°C)
Time (min)
Shelf position
Biscuits
170 - 190
10 - 20
2
Bread
200 - 220
30 - 35
2
Bread rolls / buns
200 - 220
10 - 15
2
Cakes: Small & Queen
160 - 180
18 - 25
2
Cakes: Sponges
160 - 175
20 - 30
2
Cakes: Victoria Sandwich
160 - 170
18 - 25
2
Cakes: Madeira
140 - 150
75 - 90
2
Cakes: Rich Fruit
140 - 150
120 - 150
2
Cakes: Gingerbread
140 - 150
80 - 90
2
Cakes: Meringues
90 - 100
150 - 180
2
Cakes: Flapjack
160 - 170
25 - 30
2
Cakes: Shortbread
130 - 150
45 - 60
2
Cakes: Apple Pie
170 - 180
50 - 60
2
Casseroles: Beef / Lamb
160 - 170
150 - 180
2
Casseroles: Chicken
160 - 180
80 - 90
2
Convenience Foods
Follow manufacturer`s instructions.
2
Fish
170 - 190
20 - 30
2
Fish Pie (Potato Topped)
190 - 200
20 - 30
2
Fruit Pies, Crumbles
190 - 200
30 - 50
2
Milk Puddings
150 - 170
90 - 120
2
Pasta Lasagne etc.
170 - 180
40 - 50
2
14
www.zanussi.com
Food
Temperature (°C)
Time (min)
Shelf position
Pastry: Choux
180 - 190
30 - 40
2
Pastry: Eclairs, Profiteroles
180 - 190
30 - 40
2
Pastry: Flaky / Puff Pies
210 - 220
30 - 40
2
Shortcrusts: Mince Pies
190 - 200
15 - 20
2
Shortcrusts: Meat Pies
190 - 210
25 - 35
2
Shortcrusts: Quiche, Tarts, Flans
180 - 200
25 - 50
2
Scones
220 - 230
8 - 12
3
Shepard`s Pie
190 - 200
30 - 40
2
Souffles
170 - 180
20 - 30
2
Vegetables: Baked Jacket Potatos
180 - 190
60 - 90
2
Vegetables: Roast Potatos
180 - 190
60 - 90
2
Yorkshire Pudding Large
220 - 210
25 - 40
2
Yorkshire Pudding Individual
210 - 220
15 - 25
2
Roasting Meat, Poultry
Refer to the Roasting table.
2
Thermaflow® Baking - Main Oven
Shelf positions are not critical but
ensure that the oven accessories are
evenly spaced when more than one
is used.
Food
Temperature (°C)
Time (min)
Shelf position
Biscuits
180 - 190
10 - 20
1–3
Bread
190 - 210
30 - 35
2
Cakes: Small & Queen
150 - 170
18 - 25
1–3
Cakes: Sponges
160 - 170
20 - 25
3
Cakes: Madeira
140 - 160
60 - 80
3
Cakes: Rich Fruit
130 - 140
120 - 150
3
Cakes: Christmas
130 - 140
180 - 270
3
Cakes: Apple Pie
160 - 170
50 - 60
3
- Shortbread
130 - 150
45 - 60
1–3
www.zanussi.com
15
Food
Temperature (°C)
Time (min)
Shelf position
Fish
160 - 180
30 - 40
3
Fruit Pies, Crumbles
170 - 180
30 - 50
3
Milk Puddings
140 - 160
60 - 90
3
Pastry: Choux
180 - 190
30 - 40
3
Pastry: Shortcrust
180 - 190
25 - 35
3
Pastry: Flaky
180 - 190
30 - 40
3
Pastry: Puff
Follow manufacturer`s instructions. Reduce
the temperature for Fan oven by 20 °C.
3
Plate Tarts
180 - 190
25 - 45
3
Quiches / Flans
170 - 180
25 - 45
3
Scones
210 - 230
8 - 12
1–3
Roasting: Meat, Poultry
160 - 180
Refer to the Roasting 2
table.
Roasting
•
•
Use heat-resistant ovenware to roast (refer
to the instructions of the manufacturer).
You can roast large roasting joints directly in
the deep pan (if present) or on the wire shelf
above the deep pan.
Roast lean meats in the roasting tin with the
lid. This keeps the meat more succulent.
All types of meat that can be browned or
have crackling can be roasted in the roasting
tin without the lid.
We recommend that you cook meat and fish
weighing 1 kg and above in the appliance.
•
•
•
•
•
•
•
To prevent the meat juices or fat from
burning onto the pan, put some liquid into
the deep pan.
If necessary, turn the roast (after 1/2 - 2/3 of
the cooking time).
Baste large roasts and poultry with their
juices several times during roasting. This
gives better roasting results.
You can deactivate the appliance
approximately 10 minutes before the end of
the roasting time, and use the residual heat.
Thermaflow® - Main Oven
Roasting
Food
Temperature (°C)
Time (min)
Beef / Beef boned
170 - 190
20 - 35 minutes per 0.5 kb (1 lb) and 20 - 30 minutes
over
Mutton / Lamb
170 - 190
20 - 35 minutes per 0.5 kb (1 lb) and 25 - 35 minutes
over
Pork / Veal / Ham
170 - 190
30 - 40 minutes per 0.5 kb (1 lb) and 30 - 40 minutes
over
Chicken
180 - 200
20 - 25 minutes per 0.5 kb (1 lb) and 20 minutes over
16
www.zanussi.com
Food
Temperature (°C)
Time (min)
Turkey / Goose
170 - 190
15 - 20 minutes per 0.5 kg (1 lb) up to 3.5 kg (7 lb)
then 10 minutes per 0.5 kg (1 lb) over 3.5 kg (7 lb)
Duck
180 - 200
25 - 35 minutes per 0.5 kb (1 lb) and 25 - 30 minutes
over
Pheasant
170 - 190
35 - 40 minutes per 0.5 kb (1 lb) and 35 - 40 minutes
over
Rabbit
170 - 190
20 minutes per 0.5 kb (1 lb) and 20 minutes over
Grilling in general
•
WARNING!
Always preheat an empty oven with the
grill functions for 5 minutes.
Always grill with the oven door
closed.
•
•
•
•
•
Always grill with the maximum
temperature setting.
Set the shelf into the shelf position as
recommended in the grilling table.
Always set the deep pan to collect the fat
into the first shelf position.
Set the deep pan and the trivet as
recommended in the grilling table.
Grill only flat pieces of meat or fish.
The grilling area is set in centre of the shelf.
Dual Grill - Top Oven
Food
Time (min)
Shelf position
Bacon Rashers
5-6
3
Beefburgers
10 - 20
3
Chicken Joints
20 - 40
2
Chops - Lamb
15 - 25
2-3
Chops - Pork
20 - 25
2-3
Fish - Whole / Trout / Makarel
10 - 12
2
Fillets - Plaice / Cod
4-6
2
Kebabs
12 - 18
2-3
Kidneys - Lamb / Pig
6 - 10
2-3
Sausages
20 - 30
3
Steaks: Rare
4-6
3
Steaks: Medium
6-8
3
www.zanussi.com
17
Food
Time (min)
Shelf position
Steaks: Well Done
12 - 15
3
Toasted Sandwiches
3-4
3
Defrost
•
•
Remove the food packaging. Put the food on
a plate.
Do not cover it with a bowl or a plate. This
can extend the defrost time.
•
Use the first shelf position. The one on the
bottom.
Oven - Care and cleaning
WARNING!
Refer to Safety chapters.
Notes on cleaning
•
•
•
•
•
•
Clean the front of the appliance with a soft
cloth with warm water and a cleaning agent.
To clean metal surfaces, use a usual
cleaning agent.
Clean the appliance interior after each use.
Fat accumulation or other food remains may
result in a fire. The risk is higher for the grill
pan.
Clean stubborn dirt with a special oven
cleaner.
Clean all accessories after each use and let
them dry. Use a soft cloth with warm water
and a cleaning agent.
If you have nonstick accessories, do not
clean them using aggressive agents, sharpedged objects or a dishwasher. It can cause
damage to the nonstick coating.
Stainless steel or aluminium appliances
Clean the oven door with a wet
sponge only. Dry it with a soft cloth.
Do not use steel wool, acids or
abrasive materials as they can
damage the oven surface. Clean the
oven control panel with the same
precautions.
18
Catalytic cleaning
CAUTION!
Do not clean the catalytic surface
with oven sprays, abrasive cleaning
agents, soap or other cleaning
agents. This will damage the
catalytic surface.
Spots or discolouration of the
catalytic surface have no effect on
catalytic properties.
WARNING!
Keep children away when you clean
the oven at a high temperature. The
oven surface becomes very hot and
there is a risk of burns.
CAUTION!
Always turn the oven light on while
using the catalytic cleaning (if
applicable).
Before activating the catalytic
cleaning remove all the accessories
from the oven.
The walls with a catalytic coating are selfcleaning. They absorb fat which collects on the
walls while the appliance operates.
To support the self-cleaning procedure, heat
the empty oven on a regular basis.
www.zanussi.com
Catalytic cleaning works only in the main oven.
1. Push the door trim at one side to remove it.
1. Clean the oven floor with warm water and
washing up liquid, then dry it.
2. Set the oven temperature to 250 °C and let
the oven operate for 1 hour.
3. When the appliance is cool, clean it with a
soft and moist sponge.
A
Removing and cleaning the door
glasses - top oven
2
The door glass in your product can
be different in type and shape from
the examples you see in the image.
The number of glasses can also be
different.
1
1. Open the door.
2. Hold the door trim on the top edge of the
door at the two sides and push inwards to
release the clip seal.
2. Pull up the trim.
3. Remove the glass panels.
To replace the glass panels, do the
same steps in reverse. Before you
lower the trim, attach the A trim part
to the door. Refer to the image.
1
Replacing the lamp
Put a cloth on the bottom of the interior of the
appliance. It prevents damage to the lamp glass
cover and the cavity.
WARNING!
2
1
3. Pull the door trim to the front to remove it.
4. Remove the glass panels.
To install the panels, do the same steps in
reverse.
Removing and cleaning the door
glasses - main oven
The door glass in your product can
be different in type and shape from
the example you see in the image.
The number of glasses can also be
different.
www.zanussi.com
Danger of electrocution! Disconnect
the fuse before you replace the
lamp.
The lamp and the lamp glass cover
can be hot.
1. Deactivate the appliance.
2. Remove the fuses from the fuse box or
deactivate the circuit breaker.
The back lamp
The lamp glass cover is at the back
of the cavity.
1. Turn the lamp glass cover counterclockwise
to remove it.
2. Clean the glass cover.
3. Replace the oven lamp with a suitable 300
°C heat-resistant oven lamp.
Use the same oven lamp type.
4. Install the glass cover.
19
Troubleshooting
WARNING!
Refer to Safety chapters.
What to do if...
Problem
Possible cause
Remedy
You cannot activate the appliance.
The appliance is not connected
to an electrical supply or it is
connected incorrectly.
Check if the appliance is correctly connected to the electrical
supply.
You cannot activate the appliance.
The fuse is released.
Make sure that the fuse is the
cause of the malfunction. If the
fuse releases again and again,
contact a qualified electrician.
The burners do not work.
There is no gas supply.
Check the gas connection.
There is no spark when you try to
activate the spark generator.
Burner cap and crown are placed Place the burner cap and crown
incorrectly.
correctly.
The flame extinguishes immediately after ignition.
Thermocouple is not heated up
sufficiently.
After lightning the flame, keep the
knob pushed for equal or less
than 10 seconds.
The flame ring is uneven.
Burner crown is blocked with
food residues.
Make sure that the injector is not
blocked and the burner crown is
clean.
The oven does not heat up.
The oven is deactivated.
Activate the oven.
The oven does not heat up.
The clock is not set.
Set the clock.
The oven does not heat up.
The necessary settings are not
set.
Make sure that the settings are
correct.
The lamp does not operate.
The lamp is defective.
Replace the lamp.
The display shows "12.00".
There was a power cut.
Reset the clock.
Steam and condensation settle
on the food and in the cavity of
the oven.
You left the dish in the oven for
too long.
Do not leave the dishes in the
oven for longer than 15 - 20 minutes after the cooking process
ends.
Service data
If you cannot find a solution to the problem
yourself, contact your dealer or an Authorised
Service Centre.
20
The necessary data for the service centre is on
the rating plate. The rating plate is on the front
frame of the appliance cavity. Do not remove
the rating plate from the appliance cavity.
www.zanussi.com
We recommend that you write the data here:
Model (MOD.)
.........................................
Product number (PNC)
.........................................
Serial number (S.N.)
.........................................
Installation
Levelling of the appliance
WARNING!
Refer to Safety chapters.
Technical data
Dimensions
Height
894 - 912 mm
Width
595 mm
Depth
600 mm
Use small feet on the bottom of appliance to set
the appliance top surface level with other
surfaces.
Location of the appliance
You can install your freestanding appliance with
cabinets on one or two sides and in the corner.
Anti-tilt protection
Adjust the appliance to the correct height and
put it in the correct area before you attach the
anti-tilt protection.
CAUTION!
Install the anti-tilt protection to
prevent the appliance from falling
under incorrect loads. The anti-tilt
protection only works when the
appliance is put in a correct area.
B
The anti-tilt protection has two parts (A + B).
You can find the anti-tilt protection (B) on the
right or left side of the rear wall of the appliance.
A
A
B
Minimum distances
Dimension
mm
A
2
B
685
www.zanussi.com
1. Install the anti-tilt protection (A) on the wall.
21
Make sure that the wall is made of a solid
material. If not, you need to make the wall
sufficiently strong to hold the weight.
Make sure that the surface behind the
appliance is smooth.
2. Put the appliance in the middle of the space
between the cupboards.
If the space is larger than the width of the
appliance, you must adjust the side
measurement.
3. Install the anti-tilt protection (A)
approximately 77 mm below the top surface
of the appliance and 50 mm from the left or
right side of the appliance into the circular
hole on the bracket. Screw it into the wall.
4. Check that the anti-tilt protection (A) fits
minimum 20 mm into the hole in the rear
wall of the appliance (B) when you push the
appliance.
Other technical data
WARNING!
These instructions are only valid in
the countries whose symbols appear
on this booklet's cover.
Gas category:
I2H
Gas supply G20 (2H) 20 mbar
50 mm
77 mm
A
Gas burners
BURNER
Auxiliary
Semi-rapid
Rapid
NORMAL POWER
kW
INJECTOR MARK 1/100 mm
Btu/h
1
70
3412
1.9
96
6483
3
119
10236
Gas Connection
Use a flexible pipe in compliance with the
regulation in force. Make sure they do not come
in touch with mobile parts and are not
squeezed.
WARNING!
Only a qualified and competent
person can do the gas installation.
Before you connect te gas,
disconnect the appliance from the
electricity supply or switch off the
fuse in the fuse box. Close the
primary valve of the gas supply.
22
Natural Gas
Supply piping should not be less
than R3/8. Connection is made to
the Rc 1/2 (1/2 “ B.S.P.) female
threaded. The entry pipe is located
just below the hob level on the rear
left hand side of the appliance.
The gas supply ramp is on the rear
side of the appliance.
WARNING!
Only liquid sealants can be used
when the inlet gas pipe is fitted i.e.:
do not use the P.T.F.E. sealant tape.
When the installation is complete,
carry out a gas tightness test and
make sure that the seal of each pipe
fitting does not leak.
www.zanussi.com
Checking the hob burners
Use flexible tubing, which comply
with the BS.669 current edition.
A
E
1. Lift the lid.
2. Put on the burner crowns and caps. Make
sure that they are correctly seated.
3. Put on the pan supports.
4. Light one of the hob burners.
To light the hob burner refer to the "Ignition
of the hob burners".
Check if the flame is regular.
Check each of the burners.
5. Turn the knob for the hob to the off position.
Checking the Lid Safety Device
D
B
C
C
WARNING!
The gas bayonet connector must be
in the marked area.
Dimension
1. Lift the lid.
2. Light one of the hob burners.
To light the hob burner refer to the "Ignition
of the hob burners".
3. Close the lid. There should be no gas
supply to the hob burners. The burner goes
out.
4. Turn the knob to the off position and lift the
lid. The gas supply should be restored to
the hob burners, when you turn the knob on.
Electrical installation
WARNING!
mm
The manufacturer is not responsible
if you do not follow the safety
precautions from Safety chapters.
A
250
B
680
C
50
This appliance is supplied without a main plug
or a main cable.
D
250
Covering terminal board
E
580
Pressure test
The Rapid injector is used as a pressure test
point.
1. Connect the pressure gauge to the Rapid
injector.
2. Examine the supply pressure by turning the
Rapid burner and one other burner fully on,
and lighting them. The pressure must be:
a) 20 mbar for Natural Gas
b) 29 mbar for LPG, butane only
c) 37 mbar for LPG, propane only.
3. Turn the taps off and disconnect the
pressure gauge.
4. Make sure that all burners work correctly.
www.zanussi.com
•
•
•
The recommended cross-section area is six
square millimetres (6 mm²).
When you refit the mains terminal cover,
make sure that the lower tabs are located
inside the bottom edge of the aperture,
before you fix the two screws into the top
edge of the mains terminal cover.
Make sure that the cover is securely
fastened.
23
To open the cover of terminal board
obey the procedure in opposite
sequence.
Terminal board
L
L
N
N
N
Do not remove blanking plates.
Make sure that the links are fitted as shown.
Energy efficiency
Product information for hob according to EU 66/2014
Model identification
ZCK68300B
ZCK68300W
ZCK68300X
Type of hob
Hob inside Freestanding Cooker
Number of gas burners
4
Energy efficiency per gas burner
(EE gas burner)
Left Front - Rapid
52.9 %
Left rear - Semi Rapid
54.6 %
Right front - Auxiliary
not applicable
Right rear- Semi Rapid
54.6 %
Energy efficiency for the gas hob (EE gas hob)
54.0 %
EN 30-2-1: Domestic cooking appliances
burning gas - Part 2-1 : Rational use of energy General
•
•
Hob - Energy saving
•
You can save energy during everyday cooking if
you follow below hints.
•
•
•
When you heat up water, use only the
amount you need.
If it is possible, always put the lids on the
cookware.
•
Before you use the burners and pan support
make sure they are assembled correctly.
The cookware bottom should have the
correct diameters for the burner size.
Put the cookware directly over the burner
and in the centre of it.
When the liquid starts to boil, turn down the
flame to barely simmer the liquid.
If it is possible, use a pressure cooker. Refer
to its user manual.
Product Fiche and information for ovens according to EU 65-66/2014
Supplier's name
Zanussi
Model identification
ZCK68300B
ZCK68300W
ZCK68300X
Energy Efficiency Index
Top oven: 105.6
Main oven: 104.7
24
www.zanussi.com
Energy efficiency class
Top oven: A
Main oven: A
Energy consumption with a standard load, conventional mode
Top oven: 0.75 kWh/cycle
Main oven: not applicable
Energy consumption with a standard load, fan-forced mode
Top oven: not applicable
Main oven: 0.89 kWh/cycle
Number of cavities
2
Heat source
Electricity
Volume
Top oven: 37 l
Main oven: 72 l
Type of oven
Oven inside Freestanding Cooker
Mass
EN 60350-1 - Household electric cooking
appliances - Part 1: Ranges, ovens, steam
ovens and grills - Methods for measuring
performance.
Oven - Energy saving
The appliance contains features which help you
save energy during everyday cooking.
•
General hints
– Make sure that the oven door is closed
properly when the appliance operates
and keep it closed as much as possible
during the cooking.
– Use metal dishes to improve the energy
saving.
•
•
ZCK68300B
57.5 kg
ZCK68300W
57.6 kg
ZCK68300X
55.5 kg
– When possible, put the food inside the
oven without heating it up.
– When the cooking duration is longer
than 30 minutes, reduce the oven
temperature to minimum, 3 - 10 minutes
before the end of the cooking time,
depending on the duration of the
cooking. The residual heat inside the
oven will continue to cook.
– Use the residual heat to warm up other
foods.
Cooking with fan - when possible, use the
cooking functions with fan to save energy.
Keep food warm - if you want to use the
residual heat to keep the meal warm, choose
the lowest possible temperature setting.
ENVIRONMENT CONCERNS
appliances marked with the symbol with the
household waste. Return the product to your
local recycling facility or contact your municipal
office.
Recycle the materials with the symbol . Put
the packaging in applicable containers to
recycle it. Help protect the environment and
human health and to recycle waste of electrical
and electronic appliances. Do not dispose
www.zanussi.com
25
*
26
www.zanussi.com
www.zanussi.com
27
867307997-A-432014
www.zanussi.com/shop