Zanussi ZDF14001KA dishwasher User manual

EN
User manual
Dishwasher
ZDF14001WA
ZDF14001KA
ZDF14001SA
Contents
Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Options _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Before first use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
2
4
4
5
6
7
Hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ 10
Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11
Technical information _ _ _ _ _ _ _ _ _ _ _ 12
Environment concerns _ _ _ _ _ _ _ _ _ _ _ 13
Subject to change without notice.
Safety instructions
Before the installation and use of the appliance, carefully read the supplied instructions.
The manufacturer is not responsible if an incorrect installation and use causes injuries and
damages. Always keep the instructions with
the appliance for future reference.
Children and vulnerable people safety
Warning! Risk of suffocation, injury or
permanent disability.
• Do not let persons, children included, with
reduced physical sensory, reduced mental
functions or lack of experience and knowledge use the appliance. They must have supervision or instruction for the operation of
the appliance by a person who is responsible for their safety.
• Do not let children play with the appliance.
• Keep all packaging away from children.
• Keep all detergents away from children.
• Keep children and pets away from the appliance door when it is open.
Installation
• Remove all the packaging.
• Do not install or use a damaged appliance.
• Do not install or use the appliance where
the temperature is less than 0 °C.
• Obey the installation instruction supplied
with the appliance.
Electrical connection
Warning! Risk of fire and electrical
shock.
• Make sure that the electrical information on
the rating plate agrees with the power supply. If not, contact an electrician.
• Always use a correctly installed shockproof
socket.
• Do not use multi-plug adapters and extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable. Contact
the service or an electrician to change a
damaged mains cable.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after
the installation.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
• Only for UK and Ireland. The appliance
has a 13 amp mains plug. If it is necessary
to change the fuse in the mains plug, use a
13 amp ASTA (BS 1362) fuse.
•
This appliance complies with the E.E.C. Directives.
Water connection
• Make sure not to cause damage to the water hoses.
• The appliance is to be connected to the water mains using the new supplied hose-sets.
Old hose sets must not be reused.
• Before you connect the appliance to new
pipes or pipes not used for a long time, let
the water flow until it is clean.
• The appliance must be earthed.
2
www.zanussi.com
• The first time you use the appliance, make
sure that there is no leakage.
Use
• This appliance is intended to be used in
household and similar applications such as:
– Staff kitchen areas in shops, offices and
other working environments
– Farm houses
– By clients in hotels, motels and other residential type environments
– Bed and breakfast type environments.
Warning! Risk of injury, burns, electrical
shock or fire.
• Do not change the specification of this appliance.
• Put knives and cutlery with sharp points in
the cutlery basket with the points down or in
a horizontal position.
• Do not keep the appliance door open without supervision to prevent to fall on it.
• Do not sit or stand on the open door.
• Dishwasher detergents are dangerous.
Obey the safety instructions on the detergent packaging.
• Do not drink and play with the water in the
appliance.
• Do not remove the dishes from the appliance until the programme is completed.
There can be detergent on the dishes.
www.zanussi.com
• The appliance can release hot steam if you
open the door while a programme operates.
• Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
• Do not use water spray and steam to clean
the appliance.
Disposal
Warning! Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children
and pets to get closed in the appliance.
Service
• Contact the Service to repair the appliance.
We recommend only the use of original
spare parts.
• When you contact the Service, ensure that
you have the following information that is
available on the rating plate.
Model :
PNC :
Serial Number :
3
Control panel
1
3
2
8
1 On/off button
2 Programme marker
5 Start button
6 Delay button
3 Indicators
4 Display
7 Multitab button
8 Programme knob
Indicators
7
4
6 5
Description
Washing phase indicator.
Drying phase indicator.
Rinse aid indicator. This indicator is off while the programme operates.
Salt indicator. This indicator is off while the programme operates.
Multitab indicator.
Programmes
Programme
1)
2)
4
Degree of soil
Type of load
Normal soil
Crockery and cutlery
Programme
phases
Prewash
Wash 50 °C
Rinses
Dry
Duration
(min)
195
Energy
(kWh)
1.03
Water
(l)
11
www.zanussi.com
Programme
1)
3)
4)
5)
Degree of soil
Type of load
Programme
phases
Duration
(min)
Energy
(kWh)
Water
(l)
All
Crockery, cutlery,
pots and pans
Prewash
Wash from 45 °C to 70
°C
Rinses
Dry
40 - 150
0.6 - 1.4
8 - 14
Heavy soil
Crockery, cutlery,
pots and pans
Prewash
Wash 70 °C
Rinses
Dry
130 - 150
1.3 - 1.4
13 - 15
Fresh soil
Crockery and cutlery
Wash 60 °C
Rinse
30
0.8
9
All
Prewash
14
0.1
4
1) The pressure and the temperature of the water , the variations of the mains supply, the options and the
quantity of dishes can change the values.
2) With this programme you have the most efficient use of water and energy consumption for crockery and
cutlery with normal soil. (This is the standard programme for test institutes).
3) The appliance senses the degree of soil and the quantity of items in the baskets. It automatically adjusts
the temperature and quantity of the water, the energy consumption and the programme duration.
4) With this programme you can wash a load with fresh soil. It gives good washing results in a short time.
5) Use this programme to quickly rinse the dishes. This prevents the remaining food to bond on the dishes
and bad odours to come out from the appliance.
Do not use detergent with this programme.
Information for test institutes
For all the necessary information for test performance. send an email to:
[email protected]
Write down the product number (PNC) that is on the rating plate.
Options
Multitab
Activate or deactivate the Multitab option
before the start of a programme. You
cannot activate or deactivate this option while
a programme operates.
This option deactivates the flow of rinse aid
and salt. The related indicators stay off.
1. Press Multitab, the Multitab indicator
comes on.
• The option will stay on until you deactivate it.
If you stop to use the combi detergent
tablets, before you start to use
www.zanussi.com
separately detergent, rinse aid and
dishwasher salt, do these steps:
1. Set the water softener to the highest level.
2. Make sure that the salt container and the
rinse aid dispenser are full.
3. Start the shortest programme with a rinsing phase, without detergent and without
dishes.
4. Adjust the water softener to the water
hardness in your area.
5. Adjust the released quantity of rinse aid.
This option is not applicable to
.
5
Before first use
1. Make sure that the set level of the water
softener agrees with the water hardness in
your area. If not, adjust the water softener.
Contact your local water authority to know
the water hardness in your area.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Processing residues can stay in the appliance. Start a programme to remove them.
Do not use detergent and do not load the
baskets.
If you use the combi detergent tablets,
activate the Multitab option.
Adjusting the water softener
Water softener
adjustment
Water hardness
German
degrees
(°dH)
French
degrees
(°fH)
mmol/l
Clarke
degrees
Level
47 - 50
84 - 90
8.4. - 9.0
58 - 63
10
43 - 46
76 - 83
7.6 - 8.3
53 - 57
9
37 - 42
65 - 75
6.5 - 7.5
46 - 52
8
29 - 36
51 - 64
5.1 - 6.4
36 - 45
7
23 - 28
40 - 50
4.0 - 5.0
28 - 35
6
19 - 22
33 - 39
3.3 - 3.9
23 - 27
5 1)
15 - 18
26 - 32
2.6 - 3.2
18 - 22
4
11 - 14
19 - 25
1.9 - 2.5
13 - 17
3
4 - 10
7 - 18
0.7 - 1.8
5 - 12
2
<4
<7
< 0.7
<5
12)
1) Factory position.
2) Do not use salt at this level.
How to adjust the level of the water
softener
1. Press the on/off button to activate the appliance. Make sure that the appliance is in
setting mode, refer to “Setting and starting
a programme”.
2. Turn the programme knob until the pro.
gramme marker is aligned with
3. Press and hold, at the same time, Multi,
tab and Delay until the indicators
, and
start to flash.
4. Press Multitab.
• The indicators
and
go off.
6
• The indicator
continues to flash.
• The display shows the current setting of
= level 5.
the water softener, e.g.
5. Press Multitab again and again to change
the setting.
6. Press the on/off button to deactivate the
appliance and to confirm the setting.
Filling the salt container
Caution! Water and salt can come out
from the salt container when you fill it.
Risk of corrosion. To prevent it, after you fill
the salt container, start a programme.
www.zanussi.com
3
1
4
1
2
2
1
2
3
4
To adjust the released quantity of rinse aid,
turn the selector between position 1 (lowest
quantity) and position 4 (highest quantity).
3
4
Put 1 litre of water in the salt container (only
for the first time).
Filling the rinse aid dispenser
2
1
1
2
Daily use
1. Open the water tap.
2. Press the on/off button to activate the appliance. Make sure that the appliance is in
setting mode, refer to “Setting and starting
a programme”.
• If the salt indicator is on, fill the salt container.
• If the rinse aid indicator is on, fill the
rinse aid dispenser.
3. Load the baskets.
www.zanussi.com
4. Add the detergent.
• If you use the combi detergent tablets,
activate the Multitab option.
5. Set and start the correct programme for
the type of load and the degree of soil.
7
Using the detergent
1
2
Starting a programme with delay start
2
1
A
30
B
30
20
3
20
4
Put the detergent or the tablet in compartment
(A) If the programme has a prewash phase,
put a small quantity of detergent in compartment (B).
Setting and starting a programme
Setting mode
For some settings it is necessary that the appliance is in setting mode.
The appliance is in setting mode when, after
the activation the programme duration flashes
in the display.
If the control panel does not show this condition, press and hold, at the same time, Multitab and Delay until the appliance is in setting
mode.
Starting a programme without delay start
1. Open the water tap.
2. Press the on/off button to activate the appliance.
3. Close the appliance door.
4. Turn the knob until the programme marker
is aligned with the programme you want to
set.
8
• The duration of the programme flashes
in the display.
5. Press Start.
• The programme starts and the indicator
of the running phase is on.
• The programme duration starts to decrease with steps of 1 minute.
1. Set the programme.
2. Press Delay again and again until the display shows the delay time you want to set
(from 1 to 24 hours).
• The delay time flashes in the display.
3. Press Start.
• The countdown starts to decreases with
steps of 1 hour.
When the countdown is completed, the programme starts and the indicator of the running
phase comes on.
Opening the door while the appliance
operates
If you open the door, the appliance stops.
When you close the door, the appliance continues from the point of interruption.
Cancelling the delay start while the
countdown operates
1. Press and hold, at the same time, Multitab and Delay until the programme duration flashes in the display.
2. Press Start to start the programme.
Cancelling the programme
1. Press and hold, at the same time, Multitab and Delay until the programme duration flashes in the display.
Make sure that there is detergent in the
detergent dispenser before you start a
new programme.
At the end of the programme
The display shows 0:00 and the phase indicators go off.
1. Press the on/off button to deactivate the
appliance.
www.zanussi.com
2. Close the water tap.
If you do not press the on/off button, the
AUTO OFF function automatically deactivates the appliance a few minutes after the
end of the programme.
This helps to decrease the energy consumption.
• First remove the items from the lower basket, then from the upper basket.
• There can be water on the sides and on the
door of the appliance. Stainless steel becomes cool more quickly than the dishes.
Important
• Let the dishes become cold before you remove them from the appliance. Hot dishes
can be easily damaged.
Hints and tips
The water softener
Hard water contains a high quantity of minerals that can cause damage to the appliance
and bad washing results. The water softener
neutralises these minerals.
The dishwasher salt keeps the water softener
clean and in good conditions. It is important to
set the right level of the water softener. This
makes sure that the water softener uses the
correct quantity of dishwasher salt and water.
Using salt, rinse aid and detergent
• Only use salt, rinse aid and detergent for
dishwasher. Other products can cause
damage to the appliance.
• The rinse aid helps, during the last rinsing
phase, to dry the dishes without streaks and
stains.
• Combi detergent tablets contain detergent,
rinse aid and other added agents. Be sure
that these tablets are applicable to the water hardness in your area. Refer to the instructions on the packaging of the products.
• Detergent tablets do not fully dissolve with
short programmes. To prevent detergent
residues on the tableware, we recommend
that you use the tablets with long programmes.
Do not use more than the correct quantity
of detergent. Refer to the instructions on
the detergent packaging.
www.zanussi.com
Loading the baskets
Refer to the supplied leaflet with examples of the load of the baskets.
• Only use the appliance to wash items that
are dishwasher-safe.
• Do not put in the appliance items made of
wood, horn, aluminium, pewter and copper.
• Do not put in the appliance items that can
absorb water (sponges, household cloths).
• Remove remaining food from the items.
• To remove easily remaining burned food,
soak pots and pans in water before you put
them in the appliance.
• Put hollow items (cups, glasses and pans)
with the opening down.
• Make sure that cutlery and dishes do not
bond together. Mix spoons with other cutlery.
• Make sure that glasses do not touch other
glasses.
• Put the small items in the cutlery basket.
• Put the light items in the upper basket.
Make sure that they do not move.
• Make sure that the spray arms can move
freely before you start a programme.
Before starting a programme
Make sure that:
• The filters are clean and correctly installed.
• The spray arms are not clogged.
9
• The position of the items in the baskets is
correct.
• The programme is applicable for the type of
load and for the degree of soil.
• The correct quantity of detergent is used.
• There is dishwasher salt and rinse aid (unless you use combi detergent tablets).
• The cap of the salt container is tight.
Care and cleaning
Warning! Before maintenance,
deactivate the appliance and disconnect
the mains plug from the mains socket.
Dirty filters and clogged spray arms decrease the washing results.
Make a check regularly and, if necessary,
clean them.
Cleaning the filters
7
To remove filters (B) and (C), turn the handle
counterclockwise and remove. Pull apart filter
(B) and (C). Wash the filters with water.
Remove filter (A). Wash the filter with water.
Before you put the filter (A) back, make sure
that there are no residues of food or soil in or
around the edge of the sump.
Make sure that filter (A) is correctly positioned
under the 2 guides (D).
Assemble filters (B) and (C). Put them back in
filter (A). Turn the handle clockwise until it
locks.
C
B
A
1
8
2
An incorrect position of the filters can
cause bad washing results and damage
to the appliance.
3
4
D
5
10
6
Cleaning the spray arms
Do not remove the spray arms.
If the holes in the spray arms are clogged, remove remaining parts of soil with a thin pointed object.
External cleaning
Clean the appliance with a moist soft cloth.
Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads or solvents.
www.zanussi.com
Internal cleaning
If you regularly use short duration programmes, these can leave deposits of grease
and limescale inside the appliance.
To prevent this, we recommend to run long
duration programmes at least 2 times per
month.
Troubleshooting
The appliance does not start or it stops during
operation.
Before you contact the Service, refer to the information that follows for a solution to the
problem.
With some problems, the display shows
an alarm code:
•
- The appliance does not fill with water.
Problem
You cannot activate the appliance.
•
- The appliance does not drain the water.
•
- The anti-flood device is on.
Warning! Deactivate the appliance
before you do the checks.
Possible solution
Make sure that the mains plug is connected to the mains
socket.
Make sure that there is not a damaged fuse in the fuse box.
The programme does not start.
Make sure that the appliance door is closed.
If the delay start is set, cancel the setting or wait for the end
of the countdown.
The appliance does not fill with water.
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too
low. For this information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the filter in the inlet hose is not clogged.
Make sure that the inlet hose has no kinks or bends.
The appliance does not drain the water.
Make sure that the sink spigot is not clogged.
Make sure that the drain hose has no kinks or bends.
The anti-flood device is on.
Close the water tap and contact the Service.
After the checks are completed, activate the
appliance. The programme continues from the
point of interruption.
If the problem occurs again, contact the Service.
If the display shows other alarm codes, contact the Service.
www.zanussi.com
If the washing and drying results are not
satisfactory
Whitish streaks or bluish layers on
glasses and dishes
• The released quantity of rinse aid is too
much. Adjust the rinse aid selector to a lower position.
• The quantity of detergent is too much.
11
Stains and dry water drops on glasses
and dishes
• The released quantity of rinse aid is not sufficient. Adjust the rinse aid selector to a
higher position.
• The quality of the detergent can be the
cause.
Dishes are wet
• The programme is without a drying phase or
with a low temperature drying phase.
• The rinse aid dispenser is empty.
• The quality of the rinse aid can be the
cause.
• The quality of the combi detergent tablets
can be the cause. Try a different brand or
activate the rinse aid dispenser and use
rinse aid together with the combi detergent
tablets.
Refer to ‘HINTS AND TIPS’ for other possible causes.
setting mode, refer to “Setting and starting
a programme”.
2. Turn the programme knob until the programme marker is aligned with
.
3. Press and hold, at the same time, Multi,
tab and Delay until the indicators
, and
start to flash.
4. Press Delay.
• The indicators
and
go off.
• The indicator
continues to flash.
• The display shows the current setting of
the rinse aid dispenser.
Off
On
5. Press Delay again and again to change
the setting.
6. Press the on/off button to deactivate the
appliance and to confirm the setting.
How to activate the rinse aid dispenser
1. Press the on/off button to activate the appliance. Make sure that the appliance is in
Technical information
Dimensions
Width / Height / Depth (mm)
Electrical connection
Refer to the rating plate.
Voltage
Frequency
600 / 850 / 625
220-240 V
50 Hz
Water supply pressure
Min. / max. (bar / MPa)
Water supply 1)
Cold water or hot water2)
(0.5 / 0.05 ) / (8 / 0.8 )
Capacity
Place settings
12
Power consumption
Left-on mode
0.99 W
Off-mode
0.10 W
max. 60 °C
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
2) If the hot water comes from alternative sources of energy, (e.g. solar panels, aeolian energy), use the hot
water supply to decrease energy consumption.
12
www.zanussi.com
Rating plate
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ...
Environment concerns
Recycle the materials with the symbol . Put
the packaging in applicable containers to
recycle it.
Help protect the environment and human
health and to recycle waste of electrical and
electronic appliances. Do not dispose
www.zanussi.com
appliances marked with the symbol with the
household waste. Return the product to your
local recycling facility or contact your
municipal office.
• Discard correctly the packaging material.
Recycle the materials with the symbol
.
13
14
www.zanussi.com
www.zanussi.com
15
156967010-B-332013
www.zanussi.com/shop