EN
User Manual
Oven
ZOP37907
ZOP37909
Contents
Safety information
Safety instructions
Product description
Before first use
Daily use
Clock functions
Using the accessories
2
3
6
6
7
9
10
Additional functions
Hints and tips
Care and cleaning
Troubleshooting
Installation
Energy efficiency
10
11
19
21
23
25
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an
incorrect installation and use causes injuries and damages.
Always keep the instructions with the appliance for future
reference.
Children and vulnerable people safety
•
•
•
•
•
•
•
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Do not let children play with the appliance.
Keep all packaging away from children.
Keep children and pets away from the appliance when it
operates or when it cools down. Accessible parts are hot.
If the appliance has a child safety device, we recommend you
activate it.
Cleaning and user maintenance shall not be made by children
without supervision.
Children of less than 3 years should be kept away unless
continuously supervised.
General Safety
•
2
Only a qualified person must install this appliance and replace
the cable.
www.zanussi.com
•
•
•
•
•
•
•
•
•
Internally the appliance becomes hot when in operation. Do not
touch the heating elements that are in the appliance. Always
use oven gloves to remove or put in accessories or ovenware.
Before maintenance cut the power supply.
Ensure that the appliance is switched off before replacing the
lamp to avoid the possibility of electric shock.
Do not use a steam cleaner to clean the appliance.
Do not use harsh abrasive cleaners or sharp metal scrapers to
clean the glass door since they can scratch the surface, which
may result in shattering of the glass.
If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
Excess spillage must be removed before the pyrolytic cleaning.
Remove all parts from the oven.
To remove the shelf supports first pull the front of the shelf
support and then the rear end away from the side walls. Install
the shelf supports in the opposite sequence.
The means for disconnection must be incorporated in the fixed
wiring in accordance with the wiring rules.
Safety instructions
Installation
Electrical connection
WARNING!
Only a qualified person must install
this appliance.
•
•
•
•
•
•
•
•
Remove all the packaging.
Do not install or use a damaged appliance.
Obey the installation instruction supplied
with the appliance.
Always be careful when you move the
appliance because it is heavy. Always wear
safety gloves.
Do not pull the appliance by the handle.
Keep the minimum distance from the other
appliances and units.
Make sure that the appliance is installed
below and adjacent safe structures.
The sides of the appliance must stay
adjacent to appliances or to units with the
same height.
www.zanussi.com
WARNING!
Risk of fire and electrical shock.
•
•
•
•
•
•
•
All electrical connections should be made by
a qualified electrician.
The appliance must be earthed.
Make sure that the electrical information on
the rating plate agrees with the power
supply. If not, contact an electrician.
Always use a correctly installed shockproof
socket.
Do not use multi-plug adapters and
extension cables.
Make sure not to cause damage to the
mains plug and to the mains cable. Should
the mains cable need to be replaced, this
must be carried out by our Authorised
Service Centre.
Do not let mains cables touch or come near
the appliance door, especially when the door
is hot.
3
•
•
•
•
•
•
•
•
The shock protection of live and insulated
parts must be fastened in such a way that it
cannot be removed without tools.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after
the installation.
If the mains socket is loose, do not connect
the mains plug.
Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
Use only correct isolation devices: line
protecting cut-outs, fuses (screw type fuses
removed from the holder), earth leakage trips
and contactors.
The electrical installation must have an
isolation device which lets you disconnect
the appliance from the mains at all poles.
The isolation device must have a contact
opening width of minimum 3 mm.
Fully close the appliance door, before you
connect the mains plug to the mains socket.
This appliance complies with the E.E.C.
Directives.
WARNING!
Risk of damage to the appliance.
•
•
•
•
•
Care and cleaning
Use
WARNING!
WARNING!
Risk of injury, fire, or damage to the
appliance.
Risk of injury, burns and electrical
shock or explosion.
•
•
•
•
•
•
•
•
•
•
•
•
4
To prevent damage or discoloration to the
enamel:
– do not put ovenware or other objects in
the appliance directly on the bottom.
– do not put aluminium foil directly on the
bottom of the appliance.
– do not put water directly into the hot
appliance.
– do not keep moist dishes and food in the
appliance after you finish the cooking.
– be careful when you remove or install
the accessories.
Discoloration of the enamel has no effect on
the performance of the appliance. It is not a
defect in the sense of the warranty law.
Use a deep pan for moist cakes. Fruit juices
cause stains that can be permanent.
This appliance is for cooking purposes only.
It must not be used for other purposes, for
example room heating.
Always cook with the oven door closed.
Use this appliance in a household only.
Do not change the specification of this
appliance.
Make sure that the ventilation openings are
not blocked.
Do not let the appliance stay unattended
during operation.
Deactivate the appliance after each use.
Be careful when you open the appliance
door while the appliance is in operation. Hot
air can release.
Do not operate the appliance with wet hands
or when it has contact with water.
Do not apply pressure on the open door.
Do not use the appliance as a work surface
or as a storage surface.
Open the appliance door carefully. The use
of ingredients with alcohol can cause a
mixture of alcohol and air.
Do not let sparks or open flames to come in
contact with the appliance when you open
the door.
Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
•
•
•
•
•
•
•
•
•
Before maintenance, deactivate the
appliance and disconnect the mains plug
from the mains socket.
Make sure the appliance is cold. There is the
risk that the glass panels can break.
Replace immediately the door glass panels
when they are damaged. Contact the
Authorised Service Centre.
Be careful when you remove the door from
the appliance. The door is heavy!
Clean regularly the appliance to prevent the
deterioration of the surface material.
Remaining fat or food in the appliance can
cause fire.
Clean the appliance with a moist soft cloth.
Only use neutral detergents. Do not use
abrasive products, abrasive cleaning pads,
solvents or metal objects.
If you use an oven spray, obey the safety
instructions on the packaging.
Do not clean the catalytic enamel (if
applicable) with any kind of detergent.
www.zanussi.com
Pyrolytic cleaning
Risk of Injury / Fires / Chemical
Emissions (Fumes) in Pyrolitic Mode.
•
•
•
•
•
•
Before carrying out a Pyrolitic self-cleaning
function or the First Use please remove from
the oven cavity:
– any excess food residues, oil or grease
spills / deposits.
– any removable objects (including
shelves, side rails etc., provided with the
product) particularly any non-stick pots,
pans, trays, utensils etc.
Read carefully all the instructions for
Pyrolytic cleaning.
Keep children away from the appliance while
the Pyrolytic cleaning is in operation.
The appliance becomes very hot and hot air
is released from the front cooling vents.
Pyrolytic cleaning is a high temperature
operation that can release fumes from
cooking residues and construction materials,
as such consumers are strongly advised to:
– provide good ventilation during and after
each Pyrolytic cleaning.
– provide good ventilation during and after
the first use at maximum temperature
operation.
Unlike all humans, some birds and reptiles
can be extremely sensitive to potential fumes
emitted during the cleaning process of all
Pyrolytic Ovens.
– Remove any pets (especially birds) from
the vicinity of the appliance location
during and after the Pyrolytic cleaning
and first use maximum temperature
operation to a well ventilated area.
Small pets can also be highly sensitive to the
localized temperature changes in the vicinity
www.zanussi.com
•
•
of all Pyrolytic Ovens when the Pyrolytic self
cleaning program is in operation.
Non-stick surfaces on pots, pans, trays,
utensils etc., can be damaged by the high
temperature Pyrolytic cleaning operation of
all Pyrolytic Ovens and can be also a source
for low level harmful fumes.
Fumes released from all Pyrolytic Ovens /
Cooking Residues as described are not
harmful to humans, including infants or
persons with medical conditions.
Internal light
•
The type of light bulb or halogen lamp used
for this appliance is only for household
appliances. Do not use it for house lighting.
WARNING!
Risk of electrical shock.
•
•
Before replacing the lamp, disconnect the
appliance from the power supply.
Only use lamps with the same specifications.
Disposal
WARNING!
Risk of injury or suffocation.
•
•
•
Disconnect the appliance from the mains
supply.
Cut off the mains cable and discard it.
Remove the door catch to prevent children
and pets to get closed in the appliance.
Service
•
•
To repair the appliance contact an
Authorised Service Centre.
Use original spare parts only.
5
Product description
General overview
1 2
3
4
5
5
6
4
9
3
7
2
1
1
2
3
4
5
6
7
8
9
Control panel
Knob for the oven functions
Electronic programmer
Knob for the temperature
Heating element
Lamp
Fan
Shelf support, removable
Shelf positions
8
Accessories
•
•
•
Wire shelf
For cookware, cake tins, roasts.
Grill- / Roasting pan
To bake and roast or as pan to collect fat.
Trivet
For roasting and grilling.
Use the trivet only with the Grill- /
roasting pan.
Before first use
WARNING!
Initial Cleaning
2. Press
to confirm. This is necessary only
when you set the time for the first time.
Later the new time will be saved
automatically after 5 seconds.
Remove all accessories and removable shelf
supports from the appliance.
The display shows
flashes.
Refer to Safety chapters.
Refer to "Care and cleaning"
chapter.
3. Press
or
and the set hour. "00"
to set the current minutes.
Clean the appliance before first use.
Put the accessories and the removable shelf
supports back to their initial position.
4. Press
to confirm. This is necessary only
when you set the time for the first time.
Later the new time will be saved
automatically after 5 seconds.
The display shows the new time.
Setting the time
Changing the time
After the first connection to the mains, all
symbols in the display are on for some seconds.
For the subsequent few seconds the display
shows the software version.
You can change the time of day only if the oven
is off.
After the software version goes off, the display
flashes in the display.
the time of day
To set a new time, refer to "Setting the time".
shows
1. Press
6
and "12:00". "12" flashes.
or
Press
again and again until the indicator for
to set the current hour.
www.zanussi.com
Preheating
Preheat the empty appliance to burn off the
remaining grease.
1. Set the function
and the maximum
temperature.
2. Let the appliance operate for 1 hour.
3. Set the function
temperature.
4. Let the appliance operate for 15 minutes.
Accessories can become hotter than usual. The
appliance can emit an odour and smoke. This is
normal. Make sure that the airflow in the room is
sufficient.
and the maximum
Daily use
WARNING!
Refer to Safety chapters.
Retractable knobs
To use the appliance, press the control knob.
The control knob comes out.
1. Turn the knob for the oven functions to
select an oven function.
2. Turn the knob for the temperature to select
a temperature.
3. To deactivate the appliance turn the knobs
for the oven functions and temperature to
the off position.
Activating and deactivating the
appliance
It depends on the model if your
appliance has knob symbols,
indicators or lamps:
• The indicator comes on when the
oven heats up.
• The lamp comes on when the
appliance operates.
• The symbol shows whether the
knob controls the oven functions
or the temperature.
Oven functions
Oven function
Application
Off position
The appliance is off.
True Fan Cooking
To bake on up to 3 shelf positions at the same time and to dry
food. Set the temperature 20 - 40 °C lower than for Conventional Cooking.
Conventional Cooking
To bake and roast food on 1 shelf position.
Grilling
To grill flat food and to toast bread.
www.zanussi.com
7
Oven function
Application
Fast Grilling
To grill flat food in large quantities and to toast bread.
Turbo Grilling
To roast larger meat joints or poultry with bones on 1 shelf position. Also to make gratins and to brown.
Pizza Setting
To bake food on 1 shelf position for a more intensive browning
and a crispy bottom. Set the temperature 20 - 40 °C lower than
for Conventional Cooking.
Meat
To prepare very tender and juicy roasts.
Keep Warm
To keep food warm.
Defrost
To defrost frozen food.
Pyrolysis
To activate the automatic pyrolytic cleaning of the oven. This
function burns off residual dirt in the oven.
Display
A
G
F
B
E
C
D
A)
B)
C)
D)
Timer
Heat-up and residual heat indicator
Water drawer (selected models only)
Core temperature sensor (selected models
only)
E) Door lock (selected models only)
F) Hours / minutes
G) Clock functions
Buttons
Button
Function
MINUS
To set the time.
CLOCK
To set a clock function.
PLUS
To set the time.
Heat-up indicator
When you activate an oven function, the bars in
the display
8
Description
show that the oven temperature increases or
decreases.
come on one by one. The bars
www.zanussi.com
Clock functions
Clock functions table
Clock function
Application
TIME OF DAY
To set, change or check the time of day. Refer to "Setting the
time".
MINUTE MINDER
Use to set a countdown time (maximum 23 h 59 min). This function has no effect on the operation of the appliance. You can set
the MINUTE MINDER at any time, also if the appliance is off.
DURATION
To set how long the appliance operates. Use only when an oven
function is set.
END
To set when the appliance must deactivate. Use only when an
oven function is set. You can use Duration and End at the same
time (time delay), if the appliance is to be activate and deactivate
automatically later.
Press
again and again to switch
between the clock functions.
To confirm the settings of the clock
functions, press
or wait 5
seconds for an automatic
confirmation.
Setting the DURATION or END
1. Press
again and again until the display
shows
or
or
.
flashes in the display.
2. Press
press
For Duration
or
to the set the values and
to confirm.
first you set the minutes and
then the hours, for End
first you set the
hours and then the minutes.
An acoustic signal sounds for 2 minutes after
the time ends.
or
symbol and time
setting flash in the display. The oven stops.
3. Turn the knob for the oven functions to the
off position.
4. Press any button or open the oven door to
stop the acoustic signal.
If you press
when you set the
Setting the MINUTE MINDER
1. Press
again and again until
flash in the display.
and "00"
2. Press
or
to set the MINUTE
MINDER.
First you set the seconds, then the minutes
and then the hours.
At first, the time is calculated in minutes and
seconds. When the time you set is longer
than 60 minutes, the symbol
comes on
in the display.
The appliance now calculates the time in hours
and minutes.
3. The MINUTE MINDER starts automatically
after five seconds.
After 90% of the set time, an acoustic
signal sounds.
4. When the set time ends, an acoustic signal
sounds for two minutes. "00:00" and
flash in the display. Press any button or
open the oven door to stop the acoustic
signal.
If you set the MINUTE MINDER
when the DURATION
or END
function operates, the symbol
comes on in the display.
hours for DURATION
, the
appliance goes to setting of the
END
function.
www.zanussi.com
9
Count Up Timer
The Count Up Timer cannot be used
Use the Count Up Timer to monitor how long
the oven operates. It is on immediately when the
oven starts to heat.
with the functions: Duration
End
,
.
To reset the Count Up Timer, press and hold
and
. The timer starts to count up again.
Using the accessories
WARNING!
Refer to Safety chapters.
Trivet and Grill- / Roasting pan
WARNING!
Be careful when you remove the
accessories from a hot appliance.
There is a risk of burns.
2. Put the deep pan into the oven on the
necessary shelf position.
You can use the trivet to grill flat dishes in large
quantities and to toast.
1. Put the trivet into the deep pan so that the
supports of the wire shelf point down.
You can use the trivet to roast larger pieces of
meat or poultry on one shelf position.
1. Put the trivet into the deep pan so that the
supports of the wire shelf point up.
2. Put the deep pan into the oven on the
necessary shelf position.
Additional functions
Using the Child Lock
Residual heat indicator
The Child Lock prevents an accidental
operation of the appliance.
When you deactivate the appliance, the display
If the Pyrolysis function operates, the
door is locked.
SAFE comes on in the display when
you turn a knob or press a button.
1. Do not set an oven function.
2. Press and hold
and
at the same time
for 2 seconds.
An acoustic signal sounds. SAFE comes on in
the display.
To deactivate the Child Lock, repeat step 2.
10
shows the residual heat indicator
if the
temperature in the oven is more than 40 °C.
Turn the knob for the temperature left or right to
show the oven temperature.
Automatic Switch-off
For safety reasons the appliance deactivates
automatically after some time if an oven function
operates and you do not change any settings.
www.zanussi.com
Cooling fan
Temperature (°C)
Switch-off time (h)
30 - 115
12.5
120 - 195
8.5
200 - 245
5.5
250 - maximum
3
After an automatic switch-off, press a any
button to operate the appliance again.
The Automatic switch-off does not
work with the functions: Light,
Duration, End.
When the appliance operates, the cooling fan
activates automatically to keep the surfaces of
the appliance cool. If you deactivate the
appliance, the cooling fan can continue to
operate until the appliance cools down.
Safety thermostat
Incorrect operation of the appliance or defective
components can cause dangerous overheating.
To prevent this, the oven has a safety
thermostat which interrupts the power supply.
The oven activates again automatically when the
temperature drops.
Hints and tips
on the components when you cook. This can
change the baking results and cause
damage to the enamel.
WARNING!
Refer to Safety chapters.
The temperature and baking times in
the tables are guidelines only. They
depend on the recipes and the
quality and quantity of the
ingredients used.
General information
•
•
•
•
•
The appliance has five shelf positions. Count
the shelf positions from the bottom of the
appliance floor.
The appliance has a special system which
circulates the air and constantly recycles the
steam. With this system you can cook in a
steamy environment and keep the food soft
inside and crusty outside. It decreases the
cooking time and energy consumption to a
minimum.
Moisture can condense in the appliance or
on the door glass panels. This is normal.
Always stand back from the appliance when
you open the appliance door while cooking.
To decrease the condensation, operate the
appliance for 10 minutes before cooking.
Clean the moisture after each use of the
appliance.
Do not put the objects directly on the
appliance floor and do not put aluminium foil
www.zanussi.com
Baking cakes
•
•
Do not open the oven door before 3/4 of the
set cooking time is up.
If you use two baking trays at the same time,
keep one empty level between them.
Cooking meat and fish
•
•
•
Use a deep pan for very fatty food to prevent
the oven from stains that can be permanent.
Leave the meat for approximately 15 minutes
before carving so that the juice does not
seep out.
To prevent too much smoke in the oven
during roasting, add some water into the
deep pan. To prevent the smoke
condensation, add water each time after it
dries up.
Cooking times
Cooking times depend on the type of food, its
consistency, and volume.
Initially, monitor the performance when you
cook. Find the best settings (heat setting,
cooking time, etc.) for your cookware, recipes
and quantities when you use this appliance.
11
Baking and roasting table
Cakes
Food
Conventional Cooking
Temperature (°C)
Shelf position
True Fan Cooking
Temperature (°C)
Time
(min)
Comments
Shelf position
Whisked
recipes
170
2
160
3 (2 and 4)
45 - 60
In a cake
mould
Shortbread
dough
170
2
160
3 (2 and 4)
20 - 30
In a cake
mould
Buttermilk
cheesecake
170
1
165
2
80 - 100
In a 26 cm
cake mould
Apple cake
170
2
160
2 (left and
right)
80 - 100
In two 20 cm
cake moulds
on a wire
shelf
Strudel
175
3
150
2
60 - 80
In a baking
tray
Jam-tart
170
2
165
2 (left and
right)
30 - 40
In a 26 cm
cake mould
Sponge cake 170
2
150
2
40 - 50
In a 26 cm
cake mould
Christmas
cake / Rich
160
2
150
2
90 - 120
In a 20 cm
cake mould
Plum cake1)
175
1
160
2
50 - 60
In a bread tin
Small cakes
170
3
150 - 160
3
20 - 30
In a baking
tray
-
-
140 - 150
2 and 4
25 - 35
In a baking
tray
-
-
140 - 150
1, 3 and 5
30 - 45
In a baking
tray
Biscuits /
140
pastry stripes
- one level
3
140 - 150
3
25 - 45
In a baking
tray
Biscuits /
pastry stripes
- two levels
-
140 - 150
2 and 4
35 - 40
In a baking
tray
(Apple pie)1)
fruit cake1)
- one level1)
Small cakes
- two levels1)
Small cakes
- three levels
1)
12
www.zanussi.com
Food
Conventional Cooking
Temperature (°C)
Shelf position
True Fan Cooking
Temperature (°C)
Time
(min)
Comments
Shelf position
Biscuits /
pastry stripes
- three levels
-
140 - 150
1, 3 and 5
35 - 45
In a baking
tray
Meringues one level
120
3
120
3
80 - 100
In a baking
tray
Meringues -
-
-
120
2 and 4
80 - 100
In a baking
tray
Buns1)
190
3
190
3
12 - 20
In a baking
tray
Eclairs - one
level
190
3
170
3
25 - 35
In a baking
tray
Eclairs - two
levels
-
-
170
2 and 4
35 - 45
In a baking
tray
Plate tarts
180
2
170
2
45 - 70
In a 20 cm
cake mould
Rich fruit
cake
160
1
150
2
110 - 120
In a 24 cm
cake mould
Victoria
170
1
160
2 (left and
right)
30 - 50
In a 20 cm
cake mould
two levels1)
sandwich1)
1) Preheat the oven for 10 minutes.
Bread and pizza
Food
Conventional Cooking
Temperature (°C)
White bread
Shelf position
True Fan Cooking
Temperature (°C)
Time
(min)
Comments
Shelf position
190
1
190
1
60 - 70
1 - 2 pieces,
500 gr per
piece
Rye bread
190
1
180
1
30 - 45
In a bread tin
Bread rolls1)
190
2
180
2 (2 and 4)
25 - 40
6 - 8 rolls in
a baking tray
Pizza1)
230 - 250
1
230 - 250
1
10 - 20
In a baking
tray or a
deep pan
1)
www.zanussi.com
13
Food
Conventional Cooking
Temperature (°C)
Scones1)
200
Shelf position
3
True Fan Cooking
Temperature (°C)
190
Time
(min)
Comments
Shelf position
3
10 - 20
In a baking
tray
1) Preheat the oven for 10 minutes.
Flans
Food
Conventional Cooking
Temperature (°C)
Shelf position
True Fan Cooking
Temperature (°C)
Time
(min)
Comments
Shelf position
Pasta flan
200
2
180
2
40 - 50
In a mould
Vegetable
flan
200
2
175
2
45 - 60
In a mould
Quiches1)
180
1
180
1
50 - 60
In a mould
Lasagne1)
180 - 190
2
180 - 190
2
25 - 40
In a mould
Cannelloni1)
180 - 190
2
180 - 190
2
25 - 40
In a mould
1) Preheat the oven for 10 minutes.
Meat
Food
Conventional Cooking
Temperature (°C)
Shelf position
True Fan Cooking
Temperature (°C)
Time
(min)
Comments
Shelf position
Beef
200
2
190
2
50 - 70
On a wire
shelf
Pork
180
2
180
2
90 - 120
On a wire
shelf
Veal
190
2
175
2
90 - 120
On a wire
shelf
English roast
beef, rare
210
2
200
2
50 - 60
On a wire
shelf
English roast
beef, medium
210
2
200
2
60 - 70
On a wire
shelf
English roast
beef, well
done
210
2
200
2
70 - 75
On a wire
shelf
14
www.zanussi.com
Food
Conventional Cooking
Temperature (°C)
Shelf position
True Fan Cooking
Temperature (°C)
Time
(min)
Comments
Shelf position
Shoulder of
pork
180
2
170
2
120 - 150
With rind
Shin of pork
180
2
160
2
100 - 120
2 pieces
Lamb
190
2
175
2
110 - 130
Leg
Chicken
220
2
200
2
70 - 85
Whole
Turkey
180
2
160
2
210 - 240
Whole
Duck
175
2
220
2
120 - 150
Whole
Goose
175
2
160
1
150 - 200
Whole
Rabbit
190
2
175
2
60 - 80
Cut in
pieces
Hare
190
2
175
2
150 - 200
Cut in
pieces
Pheasant
190
2
175
2
90 - 120
Whole
Fish
Food
Conventional Cooking
Temperature (°C)
Shelf position
True Fan Cooking
Temperature (°C)
Time
(min)
Comments
Shelf position
Trout / Sea
bream
190
2
175
2
40 - 55
3 - 4 fish
Tuna fish /
Salmon
190
2
175
2
35 - 60
4 - 6 fillets
Grilling
Preheat the empty oven for 3
minutes before cooking.
Food
Quantity
Pieces
Temperature (°C)
(g)
Time (min)
1st side
Shelf position
2nd side
Fillet steaks
4
800
max.
12 - 15
12 - 14
4
Beef steaks
4
600
max.
10 - 12
6-8
4
www.zanussi.com
15
Food
Quantity
Pieces
Temperature (°C)
Time (min)
(g)
1st side
Shelf position
2nd side
Sausages
8
-
max.
12 - 15
10 - 12
4
Pork chops
4
600
max.
12 - 16
12 - 14
4
Chicken (cut
in 2)
2
1000
max.
30 - 35
25 - 30
4
Kebabs
4
-
max.
10 - 15
10 - 12
4
Breast of
chicken
4
400
max.
12 - 15
12 - 14
4
Hamburger
6
600
max.
20 - 30
-
4
Fish fillet
4
400
max.
12 - 14
10 - 12
4
Toasted
sandwiches
4-6
-
max.
5-7
-
4
Toast
4-6
-
max.
2-4
2-3
4
Turbo Grilling
Beef
Food
Quantity
Temperature
(°C)
Time (min)
Shelf position
Roast beef or fillet, rare per cm of thickness
190 - 200
5-6
1 or 2
Roast beef or fillet, me- per cm of thickness
dium1)
180 - 190
6-8
1 or 2
Roast beef or fillet, well per cm of thickness
done1)
170 - 180
8 - 10
1 or 2
1)
1) Preheat the oven.
Pork
Food
Quantity (kg)
Temperature
(°C)
Time (min)
Shelf position
Shoulder, neck, ham
joint
1 - 1.5
160 - 180
90 - 120
1 or 2
Chop, spare rib
1 - 1.5
170 - 180
60 - 90
1 or 2
Meat loaf
0.75 - 1
160 - 170
50 - 60
1 or 2
Pork knuckle (precooked)
0.75 - 1
150 - 170
90 - 120
1 or 2
16
www.zanussi.com
Veal
Food
Quantity (kg)
Temperature
(°C)
Time (min)
Shelf position
Roast veal
1
160 - 180
90 - 120
1 or 2
Knuckle of veal
1.5 - 2
160 - 180
120 - 150
1 or 2
Lamb
Food
Quantity (kg)
Temperature
(°C)
Time (min)
Shelf position
Leg of lamb, roast
lamb
1 - 1.5
150 - 170
100 - 120
1 or 2
Saddle of lamb
1 - 1.5
160 - 180
40 - 60
1 or 2
Poultry
Food
Quantity (kg)
Temperature
(°C)
Time (min)
Shelf position
Poultry portions
0.2 - 0.25 each
200 - 220
30 - 50
1 or 2
Chicken, half
0.4 - 0.5 each
190 - 210
35 - 50
1 or 2
Chicken, poulard
1 - 1.5
190 - 210
50 - 70
1 or 2
Duck
1.5 - 2
180 - 200
80 - 100
1 or 2
Goose
3.5 - 5
160 - 180
120 - 180
1 or 2
Turkey
2.5 - 3.5
160 - 180
120 - 150
1 or 2
Turkey
4-6
140 - 160
150 - 240
1 or 2
Fish (steamed)
Food
Whole fish
Quantity (kg)
1 - 1.5
Temperature
(°C)
210 - 220
Time (min)
40 - 60
Shelf position
1 or 2
Defrost
Food
Quantity
(g)
Defrosting
time (min)
Further defrosting time (min)
Comments
Chicken
1000
100 - 140
20 - 30
Place the chicken on an upturned saucer placed on a
large plate. Turn halfway
through.
Meat
1000
100 - 140
20 - 30
Turn halfway through.
www.zanussi.com
17
Food
Quantity
(g)
Defrosting
time (min)
Further defrosting time (min)
Comments
Meat
500
90 - 120
20 - 30
Turn halfway through.
Trout
150
25 - 35
10 - 15
-
Strawberries
300
30 - 40
10 - 20
-
Butter
250
30 - 40
10 - 15
-
Cream
2 x 200
80 - 100
10 - 15
Cream can also be whipped
when still slightly frozen in
places.
Gateau
1400
60
60
-
Drying - True Fan Cooking
•
Cover trays with grease proof paper or
baking parchment.
For a better result, stop the oven halfway
through the drying time, open the door and
•
let it cool down for one night to complete the
drying.
Vegetables
Food
Temperature
(°C)
Time (h)
Shelf position
1 position
2 positions
Beans
60 - 70
6-8
3
1/4
Peppers
60 - 70
5-6
3
1/4
Vegetables for sour 60 - 70
5-6
3
1/4
Mushrooms
50 - 60
6-8
3
1/4
Herbs
40 - 50
2-3
3
1/4
Fruit
Food
Temperature
(°C)
Time (h)
Shelf position
1 position
2 positions
Plums
60 - 70
8 - 10
3
1/4
Apricots
60 - 70
8 - 10
3
1/4
Apple slices
60 - 70
6-8
3
1/4
Pears
60 - 70
6-9
3
1/4
18
www.zanussi.com
Care and cleaning
Pyrolysis
WARNING!
Refer to Safety chapters.
CAUTION!
Notes on cleaning
•
•
•
•
•
•
Clean the front of the appliance with a soft
cloth with warm water and a cleaning agent.
To clean metal surfaces, use a usual
cleaning agent.
Clean the appliance interior after each use.
Fat accumulation or other food remains may
result in a fire. The risk is higher for the grill
pan.
Clean stubborn dirt with a special oven
cleaner.
Clean all accessories after each use and let
them dry. Use a soft cloth with warm water
and a cleaning agent.
If you have nonstick accessories, do not
clean them using aggressive agents, sharpedged objects or a dishwasher. It can cause
damage to the nonstick coating.
Stainless steel or aluminium appliances
Clean the oven door with a wet
sponge only. Dry it with a soft cloth.
Do not use steel wool, acids or
abrasive materials as they can
damage the oven surface. Clean the
oven control panel with the same
precautions.
Removing the shelf supports
Remove all accessories and
removable shelf supports.
Do not start the Pyrolysis if you did
not fully close the oven door. In
some models, the display shows
"C3" when this error occurs.
WARNING!
The appliance becomes very hot.
There is a risk of burns.
CAUTION!
If there are other appliances installed
in the same cabinet, do not use
them at the same time as the
Pyrolysis function. It can cause
damage to the appliance.
1. Remove the worst dirt manually.
2. Clean the inner side of the door with hot
water, so that the residues do not burn from
the hot air.
3. Set the Pyrolysis function. Refer to "Oven
functions".
4. When
flashes, press
the necessary procedure:
Option
2
1
1 Pull the front of the
shelf support away
from the side wall.
2
2 Pull the rear end of
the shelf support
away from the side
wall and remove it.
Install the shelf supports in the opposite
sequence.
www.zanussi.com
to set
Description
P1
If the oven is not
very dirty. Time
of the procedure: 1 h.
P2
If you cannot
easily remove
the dirt. Time of
the procedure: 1
h 30 min.
To clean the oven, remove the shelf supports.
1
or
After 2 seconds the procedure starts.
You can use the End function to delay the start
of the cleaning procedure.
During the Pyrolysis the oven lamp is off.
5. When the oven is at its set temperature, the
door locks. The display shows the symbol
19
and the bars of the heat indicator until
the door unlocks.
To stop Pyrolysis before it is completed,
turn the knob for the oven functions to the
off position.
6. When Pyrolysis is completed, the display
shows the time of day. The oven door stays
locked.
7. When the appliance is cool again, an
acoustic signal sounds and the door
unlocks.
Cleaning reminder
To remind you that the Pyrolysis is necessary,
PYR flashes in the display for 10 seconds after
each activation and deactivation of the
appliance.
3
4
3 Close the oven door 4 Put the door on a soft
halfway to the first
cloth on a stable
opening position.
surface.
Then pull forward and
remove the door from
its seat.
5
6
The cleaning reminder goes out:
• after the end of the Pyrolysis
function.
•
if you press
and
at the
same time while PYR flashes in
the display.
Cleaning the oven door
The oven door has three glass panels.You can
remove the oven door and the internal glass
panels to clean them.
90°
5 Release the locking 6 Turn the two
system to remove the
fasteners by 90° and
glass panels.
remove them from
their seats.
7
The oven door can close if you try to
remove the glass panels before you
remove the oven door.
CAUTION!
Do not use the appliance without the
glass panels.
1
2
1
2
7 First lift carefully and
then remove the
glass panels one by
one. Start from the
top panel.
Clean the glass panels with water and soap.
Dry the glass panels carefully.
1 Open the door fully
and hold the two
door hinges.
20
2 Lift and turn the
levers on the two
hinges.
When the cleaning is completed, install the
glass panels and the oven door. Do the above
steps in the opposite sequence.
Make sure that you put the glass panels (A and
B) back in the correct sequence. The middle
panel (B) has a decorative frame. The screenprinting zone must face the inner side of the
door. Make sure that after the installation the
surface of the glass panel frame (B) on the
www.zanussi.com
screen-printing zones is not rough when you
touch it.
A
B
Replacing the lamp
Put a cloth on the bottom of the interior of the
appliance. It prevents damage to the lamp glass
cover and the cavity.
WARNING!
Danger of electrocution! Disconnect
the fuse before you replace the
lamp.
The lamp and the lamp glass cover
can be hot.
CAUTION!
Always hold the halogen lamp with a
cloth to prevent grease residue from
burning on the lamp.
1. Deactivate the appliance.
2. Remove the fuses from the fuse box or
deactivate the circuit breaker.
The back lamp
Make sure that you install the middle panel of
glass in the seats correctly.
1. Turn the lamp glass cover counterclockwise
to remove it.
2. Clean the glass cover.
3. Replace the lamp with a suitable 300 °C
heat-resistant lamp.
4. Install the glass cover.
Troubleshooting
WARNING!
Refer to Safety chapters.
What to do if...
Problem
Possible cause
Remedy
The oven does not heat up.
The oven is deactivated.
Activate the oven.
The oven does not heat up.
The clock is not set.
Set the clock.
The oven does not heat up.
The necessary settings are not
set.
Make sure that the settings are
correct.
The oven does not heat up.
The automatic switch-off is activated.
Refer to "Automatic switch-off".
www.zanussi.com
21
Problem
Possible cause
Remedy
The oven does not heat up.
The Child Lock is on.
Refer to "Using the Child Lock".
The oven does not heat up.
The fuse is released.
Make sure that the fuse is the
cause of the malfunction. If the
fuse releases again and again,
contact a qualified electrician.
The lamp does not operate.
The lamp is defective.
Replace the lamp.
It takes too long to cook the
dishes or they cook too quickly.
The temperature is too low or too
high.
Adjust the temperature if necessary. Follow the advice in the
user manual.
Steam and condensation settle
on the food and in the cavity of
the oven.
You left the dish in the oven for
too long.
Do not leave the dishes in the
oven for longer than 15 - 20 minutes after the cooking process
ends.
The display shows "C3".
The cleaning function does not
operate. You did not fully close
the door, or the door lock is defective.
Fully close the door.
The display shows "F102".
•
•
•
•
You did not fully close the
door.
The door lock is defective.
•
The display shows an error code
that is not in this table.
There is an electrical fault.
•
•
22
Fully close the door.
Deactivate the oven with the
house fuse or the safety
switch in the fuse box and activate it again.
If the display shows "F102"
again, contact the Customer
Care Department.
Deactivate the oven with the
house fuse or the safety
switch in the fuse box and activate it again.
If the display shows the error
code again, contact the Customer Care Department.
www.zanussi.com
Problem
Possible cause
The appliance is activated and
does not heat up. The fan does
not operate. The display shows
"Demo".
The demo mode is activated.
Remedy
1. Deactivate the oven.
2. Press and hold the button
.
3. When an acoustic signal
sounds, turn the knob for the
oven functions clockwise to
the first function. "Demo"
flashes in the display.
4. Turn the knob for the oven
functions to the off position.
5. Release the button
.
6. Turn the knob for the temperature clockwise and hold
it for three seconds. The
acoustic signal sounds three
times. The demo mode is deactivated.
Service data
If you cannot find a solution to the problem
yourself, contact your dealer or an Authorised
Service Centre.
The necessary data for the service centre is on
the rating plate. The rating plate is on the front
frame of the appliance cavity. Do not remove
the rating plate from the appliance cavity.
We recommend that you write the data here:
Model (MOD.)
.........................................
Product number (PNC)
.........................................
Serial number (S.N.)
.........................................
Installation
WARNING!
Refer to Safety chapters.
www.zanussi.com
23
Securing the appliance to the cabinet
Building In
min. 550
A
558
min. 560
6
B
114
16
20
600
589
573
548
594
21
6
3
Electrical installation
min. 550
558
114
16
20
580
The manufacturer is not responsible
if you do not follow the safety
precautions from the Safety
chapters.
min. 560
589
573
This appliance is supplied without a main plug
and a main cable.
Applicable types of cables for Europe:
548
594
21
9
•
•
Minimum size Cable / flex: 1,5 mm²
Cable / flex type: H07 RN-F, H05 RN-F,
H05 RRF, H05 VV-F, H05 V2V2-F (T90),
H05 BB-F
Applicable types of cables for UK only
Connection via
Oven Control Circuit
24
Min. size cable /
flex
2,5 mm²
Cable / flex type
PVC / PVC twin and earth
Fuse
15 A min.
20 A min.
www.zanussi.com
Energy efficiency
Product Fiche and information according to EU 65-66/2014
Supplier's name
Zanussi
Model identification
ZOP37907XA
ZOP37909XA
Energy Efficiency Index
100.0
Energy efficiency class
A
Energy consumption with a standard load, conventional mode
0.93 kWh/cycle
Energy consumption with a standard load, fan-forced mode
0.85 kWh/cycle
Number of cavities
1
Heat source
Electricity
Volume
72 l
Type of oven
Built-In Oven
Mass
EN 60350-1 - Household electric cooking
appliances - Part 1: Ranges, ovens, steam
ovens and grills - Methods for measuring
performance.
Energy saving
The appliance contains features which help you
save energy during everyday cooking.
•
•
•
General hints
– Make sure that the oven door is closed
properly when the appliance operates
and keep it closed as much as possible
during the cooking.
– Use metal dishes to improve the energy
saving.
– When possible, put the food inside the
oven without heating it up.
– When the cooking duration is longer
than 30 minutes, reduce the oven
•
ZOP37907XA
33.6 kg
ZOP37909XA
33.7 kg
temperature to minimum, 3 - 10 minutes
before the end of the cooking time,
depending on the duration of the
cooking. The residual heat inside the
oven will continue to cook.
– Use the residual heat to warm up other
foods.
Cooking with fan - when possible, use the
cooking functions with fan to save energy.
Residual heat
– In some oven functions if a programme
with time selection (Duration, End) is
activated and the cooking time is longer
than 30 minutes, the heating elements
deactivate automatically 10% earlier.
The fan and lamp continue to operate.
Keep food warm - if you want to use the
residual heat to keep the meal warm, choose
the lowest possible temperature setting. The
display shows the residual heat temperature.
ENVIRONMENT CONCERNS
appliances marked with the symbol with the
household waste. Return the product to your
local recycling facility or contact your municipal
office.
Recycle the materials with the symbol . Put
the packaging in applicable containers to
recycle it. Help protect the environment and
human health and to recycle waste of electrical
and electronic appliances. Do not dispose
www.zanussi.com
25
*
26
www.zanussi.com
www.zanussi.com
27
867310600-B-372014
www.zanussi.com/shop