Operating and installation instructions
Ceramic hobs with induction
KM 6357 / KM 6358
KM 6379
KM 6386 / KM 6387
To avoid the risk of accidents or
damage to the appliance it is
essential to read these instructions
before it is installed and used for the
first time.
en - GB
M.-Nr. 09 524 060
Contents
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
KM 6357 / KM 6358 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
KM 6379 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
KM 6386 / KM 6387 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cooking zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Before using for the first time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cleaning for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Before using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Induction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
The induction principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Noises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Pans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Power level range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
How the hob is operated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
To switch the hob on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Activating the cooking zones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Setting the power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Altering the power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
PowerFlex cooking area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Auto heat-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Booster function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Keeping warm function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Switching off and residual heat indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Tips on saving energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Minute minder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
To switch a cooking zone off automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
To use both timer functions at the same time . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Safety features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Safety lock / System lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Stop and Go. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2
Contents
Safety switch-off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Overheating protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Con|ctivity and Miele|home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Signing on the hob. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Signing off the hob. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Safety instructions for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Safety distances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Hob with frame or bevelled edge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Installation notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Building-in dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
KM 6357 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
KM 6379 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
KM 6386 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Installing the hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Flush-fitted hobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Building-in dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
KM 6358 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
KM 6387 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Installing the hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
After sales service, data plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
3
Warning and Safety instructions
This appliance complies with all relevant safety requirements.
Inappropriate use can, however, lead to personal injury and
damage to property.
To avoid the risk of accidents and damage to the appliance,
please read these instructions carefully before installation and
before using it for the first time. They contain important notes on
installation, safety, use and maintenance.
Miele cannot be held liable for damage caused by
non-compliance with these Warning and Safety instructions.
Keep these instructions in a safe place and ensure that new users
are familiar with the content. Pass them on to any future owner.
4
Warning and Safety instructions
Correct application
~ This hob is not designed for commercial use. It is intended for
use in domestic households and similar working and residential
environments.
~ The appliance is not intended for outdoor use.
~ It is intended for domestic use only to cook food and keep it
warm. Any other use is not supported by the manufacturer and
could be dangerous.
~ The appliance can only be used by people with reduced
physical, sensory or mental capabilities, or lack of experience and
knowledge, if they are supervised whilst using it, or have been
shown how to use it in a safe way and understand the hazards
involved.
5
Warning and Safety instructions
Safety with children
~ Children under 8 years of age must be kept away from the
appliance unless they are constantly supervised.
~ Children 8 years and older may only use the appliance
unsupervised if they have been shown how to use it in a safe way
and understand the hazards involved.
~ Children must not be allowed to clean the appliance
unsupervised.
~ This appliance is not a toy! To prevent the risk of injury, do not
allow children to play with the appliance or its controls.
~ The appliance gets hot when in use and remains hot for a while
after being switched off. Keep children well away from the appliance
until it has cooled down and there is no danger of burning.
~ Danger of suffocation. Packaging, e.g. cling film, polystyrene and
plastic wrappings, must be kept out of the reach of babies and
children. Whilst playing, children could become entangled in
packaging, or pull it over their head and suffocate.
~ Danger of burning.
Do not store anything which might arouse a child's interest in
storage areas above or behind the appliance. Otherwise they could
be tempted into climbing onto the appliance
~ Danger of burning or scalding.
Place pots and pans on the cooking zone in such a way that
children cannot pull them down and burn themselves.
~ Activate the system lock to ensure that children cannot switch on
the appliance inadvertently. Use the safety lock when the hob is in
use to prevent children from altering the settings selected.
6
Warning and Safety instructions
Technical safety
~ Installation, maintenance and repairs may only be carried out by
a Miele authorised service technician. Installation, maintenance and
repairs by unqualified persons could be dangerous.
~ A damaged appliance can be dangerous. Check the appliance
for visible signs of damage. Do not use a damaged appliance.
~ The electrical safety of this appliance can only be guaranteed if
correctly earthed. It is most important that this basic safety
requirement is observed and regularly tested, and where there is
any doubt, the household wiring system should be inspected by a
qualified electrician.
~ To avoid the risk of damage to the appliance, make sure that the
connection data (frequency and voltage) on the data plate
corresponds to the household supply, before connecting the
appliance to the mains supply.
Consult a qualified electrician if in any doubt.
~ Do not connect the appliance to the mains electrical supply by a
multi-socket adapter or extension lead. These are a fire hazard and
do not guarantee the required safety of the appliance.
~ For safety reasons, this appliance may only be used after it has
been built in.
~ This appliance must not be used in a non-stationary location (e.g.
on a ship).
~ Do not open the casing of the appliance.
Tampering with electrical connections or components and
mechanical parts is highly dangerous to the user and can cause
operational faults.
7
Warning and Safety instructions
~ While the appliance is under guarantee, repairs should only be
undertaken by a service technician authorised by Miele. Otherwise
the guarantee is invalidated.
~ The manufacturer can only guarantee the safety of the appliance
when original Miele replacement parts are used. Faulty components
must only be replaced by genuine Miele original spare parts.
~ The hob is not intended for use with an external timer switch or a
remote control system.
~ The hob must be connected to the electrical supply by a qualified
electrician. If the connection cable is faulty, it must be replaced with
a special connection cable installed by a qualified electrician. See
"Electrical connection".
~ The appliance must be disconnected from the mains electricity
supply during installation, maintenance and repair work. Ensure that
power is not supplied to the appliance until after it has been
installed or until any maintenance or repair work has been carried
out.
~ If the hob is fitted with a communication module, in addition to
disconnecting the hob, this module must also be disconnected from
the mains electricity during installation and maintenance of the hob
as well as while any repair work is being carried out.
~ Danger of electric shock.
Do not use the hob if it is faulty, or if the ceramic surface is cracked,
chipped or damaged in any way. Switch it off immediately, and
disconnect it from the mains electricity supply.
~ In areas which may be subject to infestation by cockroaches or
other vermin, pay particular attention to keeping the appliance and
its surroundings in a clean condition at all times. Any damage which
may be caused by cockroaches or other vermin will not be covered
by the guarantee.
8
Warning and Safety instructions
Correct use
~ Oil and fat can overheat and catch fire. Do not leave the
appliance unattended when cooking with oil or fat.
If oil or fat does catch fire, do not attempt to put out the flames with
water. Disconnect the appliance from the mains and use a suitable
fire blanket, saucepan lid, damp towel or similar to smother the
flames.
~ Flames could set the grease filters of a cooker hood on fire. Do
not flambé under a cooker hood.
~ Spray canisters, aerosols and other inflammable substances can
ignite when heated. Therefore do not store such items or
substances in a drawer under the appliance. Cutlery inserts must be
heat-resistant.
~ Do not heat an empty pan.
~ Do not heat up unopened tins of food on the hob, as pressure will
build up in the tin, causing it to explode.
~ Do not cover the hob, e.g. with a hob cover, a cloth or protective
foil. The material could catch fire, shatter or melt if the appliance is
switched on by mistake or if residual heat is still present.
~ When using an electrical appliance, e.g. a hand-held food
blender, near the appliance, ensure that the cable of the electrical
appliance cannot come into contact with the hot appliance. The
insulation on the cable could become damaged.
9
Warning and Safety instructions
~ If the appliance is installed behind a kitchen furniture door, it may
only be used with the furniture door open. Do not close the door
whilst the hob in use or whilst there is any residual heat present.
~ The appliance gets hot when in use and remains hot for a while
after being switched off. There is a danger of burning until the
residual heat indicators go out.
~ You could burn yourself on the hot hob. Protect your hands with
heat-resistant pot holders or gloves when handling hot pots and
pans. Do not let them get wet or damp, as this causes heat to
transfer through the material more quickly with the risk of scalding or
burning yourself.
~ When the appliance is switched on either deliberately or by
mistake, or when there is residual heat present, there is the risk of
any metal items left on the hob heating up, with the danger of
burning.
Depending on the material, other items left on the hob could also
melt or catch fire.
Damp pan lids might adhere to the ceramic surface and be difficult
to dislodge.
Do not use the appliance as a resting place.
Switch the cooking zones off after use.
~ Do not allow solid or liquid sugar, or pieces of plastic or
aluminium foil to get onto the cooking zones when they are hot, as
they can damage the ceramic surface when it cools down. If this
should occur, switch off the appliance and scrape off all the sugar,
plastic or aluminium residues whilst still hot, using a shielded
scraper blade. Wear oven gloves.
Allow the cooking zones to cool down and then clean them with a
suitable ceramic hob cleaning agent.
~ Pans which boil dry can cause damage to the ceramic glass. Do
not leave the appliance unattended whilst it is being used.
10
Warning and Safety instructions
~ Do not use pots or pans on the hob with bases with pronounced
edges or ridges. These could scratch or scour the ceramic glass
surface permanently. Only use pots and pans with smooth bases.
~ Grains of salt, sugar and sand (e.g. from cleaning vegetables)
can cause scratches if they get under pan bases. Make sure that
the ceramic surface is clean before placing pans on it.
~ Even a light object could cause damage in certain
circumstances. Do not drop anything on the ceramic surface.
~ Placing hot objects on the sensors and displays could damage
the electronics underneath them. Do not place hot pans on the
sensors and displays.
~ Induction heating works extremely quickly and so the base of the
pan could heat up to the temperature at which oil or fat self-ignites
within a very short time. Do not leave the appliance unattended
whilst it is being used.
~ Heat oil or fat for a maximum of one minute. Do not use the
Booster function to heat oil or fat.
~ For people fitted with a heart pacemaker:
Please note that the area immediately surrounding the hob is
electromagnetically charged. It is unlikely to affect a pacemaker.
However, if in any doubt, consult the manufacturer of the pacemaker
or your doctor.
~ To prevent damage to items which are susceptible to magnetic
fields, e.g. credit cards, digital storage devices, pocket calculators,
etc, do not leave them in the immediate vicinity of the hob.
11
Warning and Safety instructions
~ Metal utensils stored in a drawer under the hob can become hot if
the appliance is used intensively for a long time. Do not store any
metal items or utensils in a drawer under the hob
~ This hob is fitted with a cooling fan. If a drawer is fitted directly
underneath the hob, ensure that there is sufficient space between
the drawer and its contents and the underside of the appliance in
order to ensure sufficient ventilation of the hob.
Do not store pointed or small items or paper in the drawer. They
could get in through the ventilation slots or be sucked into the
housing by the fan and damage the fan or impair cooling.
~ Do not use two pans on a cooking zone, extended zone or
PowerFlex zone at the same time.
Cleaning and care
~ Do not use a steam cleaning appliance to clean this appliance.
The steam could reach electrical components and cause a short
circuit.
~ If the hob is built in over a pyrolitic oven or cooker, the hob
should not be used whilst the pyrolitic process is being carried out,
as this could trigger the overheating protection mechanism on the
hob (see relevant section).
12
Guide to the appliance
Models
KM 6357 / KM 6358
c
b
a
d
e
a Cooking zone with TwinBooster
b Cooking zone with Booster
cd PowerFlex cooking zones with TwinBooster
c + d can be combined to form a PowerFlex cooking area
e Control panel
13
Guide to the appliance
KM 6379
ad Cooking zones with Booster
bc PowerFlex cooking zones with TwinBooster
b + c can be combined to form a PowerFlex cooking area
e Control panel
14
Guide to the appliance
KM 6386 / KM 6387
b
c
a
f
d
e
ab Cooking zones with Booster
c Cooking zone with TwinBooster
de PowerFlex cooking zones with TwinBooster
d + e can be combined to form a PowerFlex cooking area
f Control panel
15
Guide to the appliance
Control panel
(Example)
i
h
g
j
0 1 2 3 4 5 6 7 8 9
k
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
88
0 1 2 3 4 5 6 7 8 9
h
0 1 2 3 4 5 6 7 8 9
m
n
pl
c adb e
16
f
o
Guide to the appliance
Sensor controls
a On/Off
b Safety lock
c Hours
d - For selecting the timer
- For switching between the timer functions
- For selecting the switch-off time (see "Switching off a cooking zone
automatically")
e Stop and Go
f For setting the power level
g Booster/TwinBooster
h For switching on the PowerFlex cooking area
i - For setting the time
- For setting the power level for the middle rear cooking zone, if present
j For keeping food warm
Indicator lights
k Residual heat indicator
l Indicator light for half hours with a minute minder time of more than 99 minutes
m Safety lock
n Indicator light for relevant zone, e.g. the rear right cooking zone
o TwinBooster
¤ Level 1
¥ Level 2
p Timer display
00 to 99 = Time in minutes
0.^ to 9^ = Time in hours
17
Guide to the appliance
Cooking zones
Cooking
zone
KM 6357 / KM 6358
Minimum to maximum
C in cm*
Rating in watts for 230 V**
y
18–28
Normal
TwinBooster level 1
TwinBooster level 2
2600
3000
3700
w
10–16
Normal
Booster
1400
2200
b
15–23
Normal
TwinBooster level 1
TwinBooster level 2
2100
3000
3700
x
15–23
Normal
TwinBooster level 1
TwinBooster level 2
2100
3000
3700
b+x
22–23 /
15 x 23 – 23 x 39
Normal
TwinBooster level 1
TwinBooster level 2
3400
4800
7400
Total:
7400
* Pans of any diameter within the given range may be used.
** The wattage quoted may vary depending on the size and material of the pans
used.
18
Guide to the appliance
Cooking
zone
KM 6379
Minimum to maximum
C in cm*
Rating in watts for 230 V**
y
14–20
Normal
Booster
1850
3000
w
15–23
Normal
TwinBooster level 1
TwinBooster level 2
2100
3000
3700
x
15–23
Normal
TwinBooster level 1
TwinBooster level 2
2100
3000
3700
z
10–16
Normal
Booster
1400
2200
w+x
22–23 /
15 x 23 – 23 x 39
Normal
TwinBooster level 1
TwinBooster level 2
3400
4800
7400
Total:
7400
* Pans of any base diameter within the given range may be used.
** The wattage quoted may vary depending on the size and material of the pans
used.
19
Guide to the appliance
Cooking
zone
KM 6386 / KM 6387
Minimum to maximum
C in cm*
Rating in watts for 230 V**
y
14–20
Normal
Booster
1850
3000
w
10–16
Normal
Booster
1400
2200
b
18–28
Normal
TwinBooster level 1
TwinBooster level 2
2600
3000
3700
x
15–23
Normal
TwinBooster level 1
TwinBooster level 2
2100
3000
3700
z
15–23
Normal
TwinBooster level 1
TwinBooster level 2
2100
3000
3700
x+z
22–23 /
15 x 23 – 23 x 39
Normal
TwinBooster level 1
TwinBooster level 2
3400
4800
7400
Total:
11100
* Pans of any base diameter within the given range may be used.
** The wattage quoted may vary depending on the size and material of the pans
used.
20
Caring for the environment
Disposal of the packing
material
Disposing of your old
appliance
The transport and protective packing
has been selected from materials
which are environmentally friendly for
disposal and should be recycled.
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not dispose of it with
household waste.
Recycling the packaging reduces the
use of raw materials in the
manufacturing process and also
reduces the amount of waste in landfill
sites. Ensure that any plastic
wrappings, bags, etc are disposed of
safely and kept out of the reach of
babies and young children. Danger of
suffocation.
Please dispose of it at your local
community waste collection / recycling
centre or contact your dealer for
advice.
Ensure that it presents no danger to
children while being stored for
disposal.
21
Before using for the first time
Please stick the extra data plate for the appliance supplied
with this documentation in the space provided in the "After
sales service, data plate, guarantee" section of this booklet.
Cleaning for the first time
^ Remove any protective wrapping and adhesive labels.
^ Before using for the first time, clean the appliance with a
damp cloth only and then wipe dry.
Before using for the first time
On hobs with bevelled glass edges, a small gap may be
visible between the hob and the worktop during the first
few days after installation. This gap will reduce with time as
the appliance is used and will not affect the electrical
safety of your appliance.
The metal components have a protective coating which may
give off a slight smell when heated up for the first time. The
induction coils may also give off a slight smell for the first few
hours of operation. This smell will be less noticeable with
each subsequent use before dissipating completely.
The smell and any vapours given off do not indicate a faulty
connection or appliance and they are not hazardous to
health.
Please note that the heating up time on induction hobs is
very much shorter than on conventional hobs.
22
Induction
The induction principle
An induction coil is located under each cooking zone. When
a cooking zone is switched on, this coil creates a magnetic
field which impacts directly on the base of the pan and heats
it up. The cooking zone itself is heated up indirectly by the
heat given off by the pan.
An induction cooking zone only works when a ferromagnetic
pan is placed on it (see "Pans"). The induction cooking zone
automatically recognises the size of the pan
The numbers 1 to 9 on the numerical keypad concerned will
flash
– if it is switched on without a pan in place, or if the pan is
unsuitable (non-magnetic base),
– if the diameter of the base of the pan is too small,
– or if the pan is taken off the cooking zone when it is
switched on.
If a suitable pan is placed on the cooking zone within 3
minutes, the ß will go out and you can continue as normal.
If no pan or an unsuitable pan is placed on the cooking zone,
the cooking zone will switch off automatically after 3 minutes.
Danger of burning.
Do not use the hob as a resting place for metal items (e.g.
cutlery). When the appliance is switched on either
deliberately or by mistake, or when there is residual heat
present, there is the risk of the metal items heating up,
with the danger of burning.
Switch the hob off after use.
23
Induction
Noises
When using an induction cooking zone, the following noises
can occur in the pan, depending on what it is made of and
how it has been constructed.
– On the higher power levels, it might buzz. This will
decrease or cease altogether when the power level is
reduced.
– If the pan base is made of layers of different materials (e.g.
in a sandwiched base), it might emit a cracking sound.
– Whistling might occur if linked zones (see "Booster") are
being used at the same time, and the pans also have
bases made of layers of different materials.
– You might hear a clicking sound from the electronic
switches, especially on lower power levels.
– You might hear a whirring sound when the cooling fan
switches on. It switches on to protect the electronics when
the hob is being used intensively. The fan may continue to
run after the appliance has been switched off.
24
Induction
Pans
Suitable pans include:
– stainless steel pans with a magnetic base
– enamelled steel pans
– cast iron pans
Unsuitable pans:
– stainless steel pans without a magnetic base
– aluminium and copper pans
– glass, ceramic or earthenware pots and pans
To test whether a pot or pan is suitable for use on an
induction hob, hold a magnet to the base of the pan. If the
magnet sticks, the pan is suitable.
Please be aware that the properties of the pan base can
affect the eveness with which food heats up in the pan.
To make optimum use of the cooking zones, choose pans
with diameters larger than the innermost markings but smaller
than the outermost markings. If the diameter of the pan is
smaller than the innermost marking, the induction heating will
not work. The zone will behave as if it had no pan on it.
Often the maximum diameter quoted by manufacturers refers
to the diameter of the top rim of the pot or pan. The diameter
of the base (generally smaller) is more important.
Danger of burning. Make sure that pans are placed
centrally on the cooking zone. If a pan is placed only
partially on a zone, there is a risk that the handle could get
very hot.
25
Power level range
The appliance is delivered with 9 power levels programmed as standard. If you
wish to fine-tune a setting, you can extend the power level range (see
"Programming").
Settings
Standard
factory settings
(9 power levels)
Extended
settings
(17 power levels)
1 to 2
1 to 2+
Making milk puddings
2
2 to 2+
Warming small quantities of liquid
Cooking rice
3
3 to 2+
Defrosting frozen vegetables
3
2+ to 3
Making porridge
3
2+ to 3+
Warming liquid and semi-solid foods
Making omelettes and lightly frying eggs
Steaming fruit
4
4 to 4+
Cooking dumplings
4
4 to 5+
Steaming vegetables and fish
5
5
Defrosting and heating frozen food
5
5 to 5+
Bringing large quantities of food to the boil, e.g.
casseroles Thickening custard and sauces, e.g. hollandaise
6
5+ to 6
Gently frying eggs (without overheating the fat)
6
5+ to 6+
Gently braising meat, fish and sausages (without overheating
the fat)
7
6+ to 7+
Frying pancakes etc.
7
6+ to 7
Cooking stew
8
8 to 8+
Boiling large quantities of water
Bringing to the boil
9
9
Melting butter
Dissolving gelatine
These settings should only be taken as a guide.
The power of the induction coils will vary depending on the size and material of
the pan. For this reason it is possible that the settings will need to be adjusted
slightly to suit your pans. As you use the hob, you will get to know which settings
suit your pans best.
26
Operation
How the hob is operated
The hob is equipped with electronic sensor controls which
react to finger contact.
When the hob is switched off only the symbols for the sensors
for switching the hob on and off and the safety lock are
visible.
When the hob is switched on all the other sensors light up as
well. On each of the numerical keypads, "0" lights up at
brightness level 2, and numbers 1-9 at brightness level 1.
If a power level is selected, the numbers from "0" to the level
set will light up in brightness level 2.
If the booster or keeping warm function is selected, the
relevant sensor will light up at brightness level 2.
To operate the hob, touch the relevant sensor. Each time you
touch a sensor, an audible tone sounds.
Take care to keep the control panel clean and do not
place anything on top of it. The sensors may fail to react or
they could mistake the article or any dirt for a fingertip
contact, thereby activating a function or even causing the
hob to switch off automatically (see " Safety switch-off").
Do not place hot pans on the sensors. The electronic unit
underneath could get damaged.
27
Operation
Do not leave the appliance unattended whilst it is being
used.
To switch the hob on
^ Touch the s sensor.
All the sensors will light up. If no further entry is made, the
hob will switch itself off after a few seconds for safety
reasons.
Activating the cooking zones
A cooking zone is not active if only the "0" is lit up in the
numerical keypad.
^ Touch the "0" to activate the zone.
All the power levels will light up.
Setting the power level
Standard power level range
^ Touch the appropriate number on the numerical keypad of
the cooking zone you wish to use.
Extended power level range
(see "Power level range")
^ Touch the area between the numbers.
For example, if you have selected power level 7+, the
numbers 7 and 8 will light up more brightly than the other
numbers.
Altering the power level
^ Touch the appropriate number on the numerical keypad of
the cooking zone you wish to use.
28
Operation
PowerFlex cooking area
The PowerFlex cooking zones can be combined to form a
PowerFlex cooking area. The settings for the cooking area
are controlled by the rear or left Powerflex cooking zone and
the other numerical keypad goes out, except for the symbol y
which remains lit.
Activating/deactivating
^ Touch the y sensor.
29
Operation
Auto heat-up
When Auto heat-up has been activated, the cooking zone
switches on automatically at the highest power setting and
then switches to the continued cooking setting selected. The
heat-up time depends on which continued cooking setting
has been chosen (see chart).
Activating
^ Touch the number of the continued cooking setting you
require until a tone sounds and the continued cooking
setting selected starts flashing.
The continued cooking setting selected will flash during the
heat-up time.
If the range of power levels/settings has been extended (see
"Programming") and one of the intermediate continued
cooking settings has been selected (e.g. 3+) the power level
before and after the intermediate setting will flash (e.g. 3 and
4).
Altering the continued cooking setting will deactivate auto
heat-up.
Deactivating
^ Touch the continued cooking setting which has been
selected until the display lights up constantly
or
^ select a different power level.
30
Operation
Continued
cooking setting*
Heat-up time
in minutes and seconds (approx.)
1
0 : 15
1+
0 : 15
2
0 : 15
2+
0 : 15
3
0 : 25
3+
0 : 25
4
0 : 50
4+
0 : 50
5
2 : 00
5+
5 : 50
6
5 : 50
6+
2 : 50
7
2 : 50
7+
2 : 50
8
2 : 50
8+
2 : 50
9
-
* The continued cooking settings with + after the number are
only available if the power level range has been extended
(see "Programming").
31
Operation
Booster function
The cooking zones are equipped with a Booster or
TwinBooster (see "Guide to the appliance").
When activated, the power is boosted for a maximum of 15
minutes so that large quantities can be heated up quickly,
e.g. when boiling water for cooking pasta.
The booster function can only be used on two cooking zones
at the same time.
If the Booster function is switched on when
– no setting has been selected, the cooking zone will revert
automatically to setting 9 at the end of the booster time or if
the booster function is switched off before this.
– a setting has been selected, the cooking zone will revert
automatically to the setting selected at the end of the
booster time or if the booster function is switched off
before this.
Taking a pan off the zone whilst the booster is in operation
interrupts the booster function, but not the total Booster time
of 15 minutes.
Cooking zones are networked in pairs to supply power for the
Booster function.
When the Booster function is selected a proportion of energy
is taken away from the linked cooking zone. the following
happens within the pairs:
- Auto heat-up is deactivated
- The power level is reduced
- The linked cooking zone is switched off.
32
Operation
Whilst the booster is switched on, the B sensor and all of the
numbers in the relevant numerical keypad are lit up at
brightness level 2.
To switch on the Booster
^ Touch the "0" on the numerical keypad of the cooking zone
you wish to use.
^ Select a power level if you wish.
^ Touch the B sensor.
To switch on the TwinBooster
Level 1
^ Touch the "0" on the numerical keypad of the cooking zone
you wish to use.
^ Select a power level if you wish.
^ Touch the B sensor.
The indicator light for TwinBooster level 1 ¤ lights up.
Level 2
^ Touch the "0" on the numerical keypad of the cooking zone
you wish to use.
^ Select a power level if you wish.
^ Touch the B sensor twice.
The indicator light for TwinBooster level 2 ¥ lights up.
To switch off the Booster/TwinBooster
^ Touch the B sensor
- once (for the Booster)
- repeatedly until the indicator lights go out
(for the TwinBooster).
or
^ select a different power level.
33
Operation
Keeping warm function
Some cooking zones have a keeping warm function.
This function is for keeping food that has just been cooked
warm, i.e. food that is still hot. It is not for reheating food
that has gone cold.
If the keeping warm function has been activated, the cooking
zone will switch off automatically after a maximum of 2 hours.
To switch the keeping warm function on/off
^ Touch the 2 sensor for selecting the cooking zone you
want.
Useful tips
– Only use pans for keeping food warm. Cover the pan with
a lid.
– You do not have to stir food while it is being kept warm.
– Nutrients are lost when food is cooked, and this will
continue when food is kept warm. The longer food is kept
warm for, the greater the loss of nutrients. Try to ensure
that food is kept warm for as short a time as possible.
34
Operation
Switching off and residual heat indicators
Switching off a cooking zone
^ Touch the "0" on the numerical keypad of the cooking zone
you wish to use.
The numbers 1 to 9 will go out after a few seconds. If the
cooking zone is still hot, residual heat will then be indicated in
the display.
Switching off the hob
^ Touch the s sensor.
This switches off all cooking zones. All the sensors will go out.
Residual heat indicator
If there is any residual heat, the numbers 1 to 9 in the
numerical keypads will go out after a few seconds. The
residual heat indicator will appear in the display of any
cooking zone which is still hot.
The lines of the residual heat indicator go out one after
another as the cooking zone cools down. The "0" will go out at
the same time as the last line.
Danger of burning and fire hazard.
Do not touch the cooking zones whilst the residual heat
indicators are lit up.
35
Tips on saving energy
– Use a pan lid whenever possible to minimise heat loss.
uncovered
covered
– Select a smaller pan when cooking small quantities. A
smaller pan uses less energy than a larger pan with very
little in it.
– Cook with as little water as possible.
– Once food has come to the boil or the oil in the pan is hot
enough for frying, reduce the heat to a lower setting.
– Cooking times are greatly reduced when using a pressure
cooker.
36
Timer
The hob must be switched on to use the timer.
The timer can be used for two different functions:
– to set the minute minder
– to set a cooking zone to switch off automatically.
You can select a time from 1 minute (01) to 9 hours (9^).
A time of up to 99 minutes is set and displayed in minutes.
Example:
To set a time of more than 99 minutes, the timer must be set
to hours (h). The time is then set in half hour stages. The half
hour is indicated by a dot after the number.
Example (2 h 30 min):
h
When the set time has elapsed 00 will appear in the timer
display. At the same time an audible tone will sound for a few
seconds.
37
Timer
Minute minder
To set the minute minder time
Minutes
Example: You want to set 15 minutes.
^ Switch the hob on.
^ Touch the m sensor.
The m indicator light will flash. 00 will appear in the timer
display. The 0 on the right will flash.
h
Enter the tens first and then the units.
^ Touch the number on the numerical keypad which
corresponds to the tens position (1 in this case).
The timer display will change and 1 will start flashing.
h
^ Touch the number on the numerical keypad which
corresponds to the units position (5 in this case).
The timer display will change. The 1 moves to the left and 5
appears on the right.
h
After a few seconds the m sensor will light up constantly and
the minute minder time will begin to count down.
38
Timer
Hours
Whole hours are set by touching the relevant number on the
numerical keypad.
Half hours are set by touching the area between the relevant
two numbers.
Example: You want to set 2 hours 30 minutes.
^ Switch the hob on.
^ Touch the m sensor.
The m indicator light will flash. 00 will appear in the timer
display. The 0 on the right will flash.
h
^ Touch the h sensor, to change the display to show the
hours.
h
^ Touch the area between the numbers 2 and 3 on the
numerical keypad.
h
After a few seconds the m sensor and the timer display will
light up constantly. The minute minder time will begin to count
down.
39
Timer
To change the minute minder time
^ Touch the m sensor.
^ Set the time you want, as described above.
To delete the minute minder time
^ Touch the m sensor.
^ Touch 0 on the numerical keypad.
40
Timer
To switch a cooking zone off automatically
You can set a time at the end of which a cooking zone will
switch off automatically.
All the cooking zones can be programmed at the same time.
If the time programmed is longer than the maximum
operational time allowed, the cooking zone will switch off
after the maximum time allowed (see "Safety switch-off").
^ Select a power level for the cooking zone you require.
^ Touch the m sensor repeatedly until the indicator light for
this cooking zone flashes.
If more than one cooking zone is switched on, the indicator
lights will flash clockwise beginning with the front left zone.
^ Set the time you want.
The time set will then count down in minutes. The time
remaining will be shown in the timer display. You can change
this at any time.
If you want to set another cooking zone to switch off
automatically, follow the same steps as described above.
If more than one switch-off time is programmed, the shortest
time remaining will show in the display, and the
corresponding indicator light will flash. All the other indicator
lights will light up constantly. If you want to check on the time
remaining for another zone, touch the m sensor repeatedly
until the indicator light for the zone you require flashes.
41
Timer
To use both timer functions at the same time
The minute minder and automatic switch-off functions can be
used at the same time.
If you have programmed in one or more switch-off times, and
would like to use the minute minder as well:
Touch the m sensor repeatedly until the indicator lights for
the cooking zones you have programmed light up constantly
and 00 appears in the timer display.
If you are using the minute minder, and would like to
programme in one or more switch-off times as well:
Touch the m sensor repeatedly until the indicator light for the
cooking zone you require flashes.
Shortly after the last entry, the timer display switches to the
function with the shortest remaining time.
If you want to show the times remaining which are counting
down in the background, touch the m repeatedly until
- the indicator lamp for the cooking zone you want flashes
(automatic switch-off).
- only the timer display is flashing (minute minder).
Starting with the shortest time remaining which is shown in
the display, all cooking zones which are switched on and the
minute minder are selected clockwise.
42
Safety features
Safety lock / System lock
Keep children away from the hob for their own safety.
Your appliance is equipped with a safety lock to prevent the
hob and the cooking zones being switched on or any settings
being altered.
The safety lock is set with the hob switched on. When
activated:
– The cooking zone power levels and the timer settings
cannot be changed.
– The cooking zones, the hob and the timer can be switched
off, but once switched off cannot be switched on again.
The system lock is set with the hob switched off. When
activated, the hob cannot be switched on and the timer
cannot be used.
The default setting for activating the system lock is manual.
The system lock can also be set for manual and automatic
activation, in which case it will be activated automatically five
minutes after the hob has been switched off, unless you set it
manually (see "Programming").
If an unavailable sensor is touched whilst the safety lock or
system lock is activated, the safety lock indicator will light up
and LC will appear in the timer display for a few seconds.
The hob is programmed at the factory for three-finger
operation. You can alter the setting from three-finger to
one-finger operation (see "Programming").
If there is an interruption to the power supply, the safety
lock and the system lock will be deactivated.
43
Safety features
Activating
Three-finger operation (standard default setting)
^ Touch the $ sensor and the "0" setting of both right-hand
cooking zones at the same time until the safety lock
indicator lights up and LC appears in the timer display.
The safety lock indicator and LC will go out after a short while.
One-finger operation
^ Touch the $ sensor until the safety lock indicator lights up
and LC appears in the timer display.
The safety lock indicator and LC will go out after a short while.
Deactivating
Three-finger operation (standard default setting)
^ Touch the $ sensor and the "0" setting of both right-hand
cooking zones at the same time until the safety lock
indicator and LC in the timer display go out.
One-finger operation
^ Touch the $ sensor until the safety lock indicator and LC in
the timer display go out.
44
Safety features
Stop and Go
Your appliance has a Stop and Go feature which, when
activated, reduces the power of all cooking zones in use to
power level 1. When Stop and Go is activated, the cooking
zone power levels and the setting of the timer cannot be
altered and the hob can only be switched off.
When Stop and Go is deactivated, the cooking zones resume
at the power level which was last set.
If Stop and Go is not deactivated, the hob switches off after 1
hour.
When Stop and Go is activated
- the countdown of a time programmed in for automatic
switch-off will be interrupted. When deactivated, the time
will continue to run.
- the minute minder will continue without interruption.
Activating
^ Touch the ž sensor.
The power of the cooking zones in use will be reduced to
power level 1.
Deactivating
^ Touch the ž sensor.
The cooking zones will now run at the level that was
previously set.
45
Safety features
Safety switch-off
Safety switch-off with an over-long cooking time
If one of the cooking zones is heated for an unusually long
period of time (see chart) and the power level is not altered,
the hob will switch itself off automatically and the relevant
residual heat indicator will light up.
To use the cooking zone again, switch it back on in the usual
way.
Power level*
Maximum operating time in hours
1 / 1+
10
2 / 2+
5
3 / 3+
5
4 / 4+
4
5 / 5+
3
6 / 6+
2
7 / 7+
2
8 / 8+
2
9
1
* The continued cooking settings with + after the number are
only available if the power level range has been extended
(see "Programming").
Safety switch-off if the sensors are covered
Your hob will switch off automatically if one or several of the
sensors remain covered for more than about 10 seconds, for
example by finger contact, food boiling over, or by an object
such as an oven glove or a tea towel.
F will appear in the timer display.
^ Clean the control panel or remove the obstruction.
F will disappear. You can now use the hob again.
46
Safety features
Overheating protection
All the induction coils and the cooling elements for the
electronics are fitted with an overheating protection
mechanism. Before the induction coils or cooling elements
get too hot, the overheating protection mechanism cuts in in
one of the following ways:
Induction coils
– If the booster function is being used, this will be switched
off.
– The power level will be reduced.
– The cooking zone will switch off automatically.
"FE" will flash in the timer display alternately with "44".
You will be able to use the cooking zones again as usual
when the fault code has gone out.
Cooling elements
– If the booster function is being used, this will be switched
off.
– The power level will be reduced.
– The cooking zones will switch off automatically.
The affected cooking zones can only be used again as usual
once the cooling element has cooled down to a safe level.
The overheating mechanism can be triggered by:
– Heating up an empty pan.
– Fat or oil being heated up on a high power level.
– Insufficient ventilation to the underside of the appliance.
– A hot cooking zone being switched on after a power cut.
If the overheating protection mechanism triggers again,
contact the Service department.
47
Cleaning and care
Danger of injury.
Do not use a steam cleaning appliance to clean this
appliance. The steam could reach electrical components
and cause a short circuit.
The appliance should be cleaned after each use. Let it cool
down to room temperature before cleaning.
To avoid water marks and limescale deposits, use a soft cloth
to dry the appliance after cleaning.
To avoid damaging the surface of your appliance, do not
use:
– washing-up liquid,
– cleaning agents containing soda, alkalines, ammonia,
acids or chlorides,
– cleaning agents containing descaling agents,
– stain or rust removers,
– abrasive cleaning agents, e.g. powder cleaners and cream
cleaners,
– solvent-based cleaning agents,
– dishwasher cleaner,
– grill and oven cleaners,
– glass cleaning agents,
– hard, abrasive brushes or sponges, e.g. pot scourers, or
sponges which have been previously used with abrasive
cleaning agents,
– melamine eraser blocks,
– sharp, pointed objects which could damage the seal
between the ceramic surface and the surrounding frame,
and between the frame and the worktop.
48
Cleaning and care
Do not use washing-up liquid to clean the ceramic surface.
Washing-up liquid will not remove all soiling and deposits.
It will form an invisible coating which will cause permanent
discolouration of the ceramic surface.
Clean the hob regularly with a suitable ceramic hob
cleaning agent.
Wipe off all coarse soiling using a damp cloth. Stubborn
soiling may need to be removed with a shielded scraper
blade.
Then clean the hob with Miele ceramic and stainless steel
hob cleaner (see "Optional accessories") applied with kitchen
paper or a clean cloth. Do not apply cleaner whilst the
appliance is still hot, as this could result in marking. Please
follow the manufacturer's instructions.
Finally wipe the hob with a damp cloth, then dry with a soft,
dry cloth. Residues can burn onto the appliance the next time
it is used, and cause damage to the ceramic surface. Ensure
that all cleaning agent residues are removed.
Spots caused by limescale, water and aluminium residues
(spots with a metallic appearance) can be removed using
Miele's ceramic and stainless steel hob cleaner.
Danger of burning.
Protect your hands with oven gloves before using a
shielded scraper blade to remove sugar, plastic or
aluminium residues from the hot hob.
Should any sugar, plastic or aluminium foil spill or fall onto
a hot cooking zone while it is in use, first switch off the
appliance. Then carefully scrape off all the sugar, plastic or
aluminium residues from the hob immediately whilst they are
still hot, using a shielded scraper blade.
Allow the appliance to cool down and then clean as
described above.
49
Programming
You can change the default settings of the programme
options (see chart). Several settings can be altered in
succession.
After selecting programming mode, P (Programme) and S
(Status) will appear in the timer display. On hobs with 3
cooking zones, an additional indicator will appear at the rear
left.
The programme is shown in the numerical keypad displays at
the front left and rear left. Example:
Programme 3 = front left 3, rear left 0
Programme 14 = front left 4, rear left 1
The status is shown in the numerical keypad display at the
rear right.
Once you have left the programming mode, the hob will be
reset automatically. This is completed when an indicator
above the s sensor lights up briefly.
Do not switch the hob on again until the reset process is
completed.
To call up programming mode
^ With the hob switched off, touch the s and $ sensors at
the same time until the safety lock indicator light flashes.
To set the programme setting
^ To set the units position touch the relevant number on the
front left numerical keypad.
^ To set the tens position touch the relevant number on the
rear left numerical keypad.
To set the status setting
^ Touch the appropriate number on the front right numerical
keypad.
To save settings
^ Touch the s sensor until all the displays go out.
To not save settings
^ Touch the $ sensor until all the displays go out.
50
Programming
Programme*
P
P
P
P
P
P
P
*
0
1
2
3
4
5
6
Demonstration mode and
factory default settings
Stop and Go
Power level range
Induction warning tone
when there is no pan or
the pan is unsuitable
Keypad tone when a
sensor is touched
Timer audible tone
Safety lock
Status** Setting
S
0
Demonstration mode on
S
1
Demonstration mode off
S
9
Factory default settings reinstated
S
0
Off
S
1
On
S
0
9 power levels
(1, 2, 3 ... to 9)
S
1
17 power levels/settings
(1, 1+, 2, 2+, 3 ... to 9)
S
0
Off
S
1
Quiet
S
2
Medium
S
3
Loud
S
0
Off
S
1
Quiet
S
2
Medium
S
3
Loud
S
0
Off
S
1
Quiet for 10 seconds
S
2
Medium for 10 seconds
S
3
Loud for 10 seconds
S
0
One-finger locking using $
S
1
Three-finger locking using $ and
"0" on the two right-hand cooking
zones
Programme /Status numbers not shown here have no allocation.
** The factory default settings are shown in bold.
51
Programming
Programme*
P
P
P
P
P
7
8
10
15
16
System lock
Status** Setting
S
0
Manual activation of the system
lock only
S
1
Manual and automatic activation
of the System lock
S
0
Off
S
1
On
Miele|home
- only on
communication-enabled
appliances fitted with a
communication module.
S
0
Feature not fitted
S
1
Signed off
S
2
Signed on
Audible tone if a sensor
is covered
S
0
Off
S
1
On
Sensor reaction speed
S
0
Slow
S
1
Standard
S
2
Rapid
Auto heat-up
* Programmes / Status numbers not shown here have no allocation.
** The factory default settings are shown in bold.
52
Problem solving guide
With the help of the following notes, minor faults in the performance of the
appliance, some of which may result from incorrect operation can be put right
without contacting the Service Department.
Installation work and repairs to electrical appliances must only be carried out
by a suitably qualified and competent person in strict accordance with current
local and national safety regulations. Do not attempt to open the casing of the
appliance. Repairs and other work by unqualified persons could be dangerous
and Miele cannot be held liable for unauthorised work.
Problem
Possible cause
The hob or cooking
zones cannot be
switched on.
The mains fuse has tripped. Reset the trip switch in the
mains fuse box (minimum
fuse rating - see data
plate).
There may be a technical
fault.
Remedy
Disconnect the appliance
from the electricity supply
for approx. 1 minute. To do
this:
– switch off at the isolator,
or
– disconnect the mains
fuse.
Reset the trip switch in the
mains fuse box, and switch
the appliance back on. If it
still will not switch on,
contact a qualified
electrician or the Miele Service Department.
53
Problem solving guide
Problem
Possible cause
Remedy
The smell and vapours will
be less noticeable with
each subsequent use
before dissipating
completely.
A smell and vapours
are given off when a
new appliance is
being used.
The power levels 1 to
9 flash.
There is no pan on the
Use a suitable pan (see
cooking zone, or the pan is "Pans").
unsuitable.
After the hob is
switched on "LC"
appears in the timer
display for a few
seconds.
The system lock is
activated.
Deactivate the system lock
(see "Safety lock / System
lock").
After the hob is
The appliance is in
switched on "dE"
demonstration mode.
appears in the timer
display for a few
seconds.
The cooking zones do
not heat up.
Deactivate demonstration
mode (see
"Programming").
A cooking zone or the A cooking zone has been
whole hob switches
in use for too long.
off automatically.
You can use the cooking
zone again by switching it
back on (see "Safety
switch-off").
The overheating protection See "Overheating
mechanism has triggered. protection".
The Booster has
deactivated early
automatically.
The cooking zone is
not working in the
usual way at the
power level set.
54
The overheating protection See "Overheating
mechanism has triggered. protection".
Problem solving guide
Problem
Possible cause
Remedy
Power level 9 is
automatically reduced
if you select power
level 9 on two linked
cooking zones or
extended zones at the
same time.
Operating both zones
at power level 9 would
exceed the permitted
maximum power level
for the two zones.
The hob switches off
while it is in use and an
F flashes in the timer
display.
Clean the control panel or
One or more of the
remove the obstruction (see
sensors have been
covered, e.g. by finger "Safety switch-off").
contact, food boiling
over or by an object
such as an oven glove.
The food in the pan
does not heat up when
the Auto heat-up
function is switched
on.
There is too much food Start cooking at the highest
in the pan.
power level and then turn
down to a lower one
manually later on.
The cooling fan
continues to run even
after the appliance has
been switched off.
The fan will continue
running until the
appliance has cooled
down. It will then
switch itself off
automatically.
The pan is not
conducting heat
properly.
55
Problem solving guide
Problem
Possible cause
Remedy
The sensors are
over-sensitive or do
not react at all.
The sensitivity level of the Make sure that there is no
sensors has changed.
direct light (from the sun or
from an artificial source)
falling onto the hob and that
the surrounding area is not
too dark.
Make sure that there is
nothing covering the sensors
or the hob. Take any pans off
the hob and wipe away any
food deposits. Interrupt the
power supply to the hob for
approx. 1 minute. If this does
not solve the problem, please
call the Miele Service
department.
FE flashes alternately
with numbers in the
timer display.
FE 44
The overheating protection See "Overheating protection".
mechanism has triggered.
FE 47
The fan is either blocked
or faulty.
FE 48
Other fault messages There is an electronic
FE..
fault.
56
Make sure it has not been
blocked by something like a
fork. Remove the cause of the
blockage. If the fault message
appears again, call the Miele
Service Department.
Interrupt the power supply to
the hob for approx. 1 minute.
If the problem persists after
reconnecting the appliance to
the power supply, please
contact the Miele Service
department.
Optional accessories
Miele offer a comprehensive range of useful accessories as
well as cleaning and conditioning products for your Miele
appliances.
These can be ordered online at:
or from Miele (see back cover for contact details)
Pans
Miele offer a wide range of pans which are perfect for Miele
hobs. Please refer to the Miele website for more details on
individual products.
Pans in various sizes
Frying pan with lid
Non-stick pans
Wok
Gourmet oven dish
Cleaning products
Ceramic and stainless steel hob cleaner 250 ml
Removes heavy soiling, limescale deposits and aluminium
residues.
E-Cloth (microfibre cloth)
Removes finger marks and light soiling.
57
Optional accessories
Miele|home system
The Miele{home system allows communication-enabled
appliances to send operating and status information to a
display appliance via the household electrical supply system
(Powerline Technology).
SuperVision appliances can display status information from
other domestic appliances. For your hob, the main status
displayed is: On, Off, Fault
Status information for domestic appliances can be displayed
and some controls operated within the home network area on
a PC, Notebook or iPod* / iPhone* (mobile terminals) via a
Miele|home Gateway.
For your hob, for example, the following information is
displayed: Setting of each cooking zone, minute minder,
switching off time for each cooking zone. The only available
control command is "switch hob off".
* * iPod und iPhone are registered trade marks of Apple Inc.
Con|ctivity is the communication between the hob and the
cooker hood. Operation of the cooker hood occurs
automatically in conjunction with the hob.
The hob sends information on its operating status via the
household electrical supply.
To enjoy the benefits of this feature, your appliance needs to
be fitted with a communication module.
Detailed information about the Miele|home system can be
found at www.miele.de.
XKM 2100 KM
Communication module including installation accessories
- for Miele hobs -
XGW 2000
Miele|home Gateway
The gateway is the bridge between the Powerline
communication of the appliances and your home network.
58
Optional accessories
Miele|home
a Communication enabled appliances (examples)
b Communication module
c SuperVision appliance
d Electrical supply (Powerline)
e Miele|home Gateway
f WLAN) Router
Possible connections (optional)
g PC, Notebook
h iPod* or iPhone*
i Connection with a domestic bus system display
j Possible internet connection
* * iPod und iPhone are registered trade marks of Apple Inc.
59
Optional accessories
Con|ctivity
a Communication module XKM 2000 DA
b Communication module XKM 2100 KM
c Electrical supply (Powerline)
60
Con|ctivity and Miele|home
Signing on the hob
If you want to sign the hob
– on to the Miele{home system, first prepare the signing on
procedure on the master appliance (see the "Miele|home"
fitting and installation instructions)
– on to the Con|ctivity system, first sign on the cooker
hood (see the "Con|ctivity" fitting and installation
instructions).
^ With the hob switched off, touch the s and $ sensors at
the same time until the safety lock indicator light flashes.
After selecting programming mode, P (Programme) and S
(Status) will appear in the timer display.
The programme number will appear on the left of the
numerical keypad and the status currently set will appear on
the right.
^ Touch number 1 on the rear left numerical keypad (set
Programme 10).
^ Touch number 2 on the front right numerical keypad (set
Status 2 = sign on).
The signing on process will begin and the number 2 will flash
in the front right numerical keypad. The signing on process
will take a few minutes. The number 2 will light up constantly
when the process has been completely successfully.
^ To save the setting, touch the s sensor until all the
displays go out.
^ Proceed as described in the "Miele|home" or Con|ctivity
fitting and installation instructions.
61
Con|ctivity and Miele|home
Signing off the hob
If you want to sign off from the Miele{home system, first
prepare the signing off procedure on the master appliance
(see the "Miele|home" fitting and installation instructions).
^ With the hob switched off, touch the s and $ sensors at
the same time until the safety lock indicator light flashes.
After selecting programming mode, P (Programme) and S
(Status) will appear in the timer display.
The programme number will appear on the left of the
numerical keypad and the status currently set will appear on
the right.
^ Touch number 1 on the rear left numerical keypad (set
Programme 10).
^ Touch number 1 on the front right numerical keypad (set
Status 1 = sign off).
The signing off process will begin and the number 1 will flash
in the front right numerical keypad. The signing off process
will take a few minutes. The number 1 will light up constantly
when the process has been completely successfully.
^ To save the setting, touch the s sensor until all the
displays go out.
^ Proceed as described in the "Miele|home" or Con|ctivity
fitting and installation instructions.
62
Safety instructions for installation
The appliance must only be installed
and connected to the electricity
supply by a suitably qualified and
competent person in strict
accordance with current national
and local safety regulations.
Fit the wall units and extractor hood
before fitting the hob to avoid
damaging the appliance.
~ After installation, ensure that the
connection cable is without hindrance
and that there is no mechanical
obstruction which could damage it.
All dimensions in this instruction booklet
are given in mm.
~ The veneer or laminate coatings of
worktops (or adjacent kitchen units)
must be treated with 100 °C
heat-resistant adhesive which will not
dissolve or distort.
Any backmoulds must be of
heat-resistant material.
This appliance must not be installed
over a fridge, fridge-freezer, freezer,
dishwasher, washing machine,
washer-dryer or tumble dryer.
~ This hob must not be installed
above ovens or cookers unless these
have a built-in cooling down fan.
63
Safety distances
Safety distance above the appliance
When two or more appliances which
have different safety distances are
installed together below a cooker
hood, you should observe the
greater safety distance of the two.
A minimum safety distance must be
maintained between the appliance and
the cooker hood above it. See the
cooker hood manufacturer's operating
and installation instructions for details.
If the manufacturer's instructions are
not available for the cooker hood, a
minimum safety distance of at least
760 mm must be maintained. For any
flammable objects, e.g. utensil rails,
wall units etc. a minimum distance of at
least 760 mm must be maintained
between them and the appliance
below.
64
Safety distances
Safety distances to the sides and
back of the hob
Ideally the hob should be installed with
plenty of space on either side. There
may be a wall at the rear or a tall unit or
wall on one side (right or left) (see
illustrations).
a Minimum distance of 50 mm
between the back of the worktop
cut-out and the rear edge of the
worktop.
Not allowed
b Minimum distance of 50 mm
between the worktop cutout and a
wall or tall unit to the right of it.
c Minimum distance of 50 mm
between the worktop cutout and a
wall or tall unit to the left of it.
Recommended
Not recommended
Not recommended
65
Safety distances
Safety distances underneath the hob
Interim shelf
To ensure sufficient ventilation to the
hob, a certain gap must be left between
the underside of the hob and any oven,
interim shelf or drawer.
It is not necessary to fit an interim shelf
underneath the hob, but one may be
fitted if you wish.
The minimum gap between the
underside of the hob and
– the top of an oven is 15 mm.
– the top of an interim shelf is 15 mm.
– the base of a drawer is 75 mm.
66
Leave a gap of 10 mm at the back of
the shelf to accommodate the cable.
We recommend a gap at the front of the
shelf of 20 mm to ensure good
ventilation.
Safety distances
Safety distance when installing the appliance near a wall with additional
niche cladding
A minimum safety distance must be maintained between the worktop cut-out and
any niche cladding to protect it from heat damage.
If the niche cladding is made from a combustible material (e. g. wood) a
minimum safety distance e of 50 mm must be maintained between the cut-out
and the cladding.
If the niche cladding is made from a non-combustible material (e. g. metal,
natural stone, ceramic tiles) a minimum safety distance e of 50 mm less the
thickness of the cladding must be maintained between the cut-out and the
cladding.
Example: 15 mm niche cladding
50 mm - 15 mm = minimum safety distance of 35 mm
Flush-fitted hobs
Hob with frame or bevelled edge
a Masonry
b Niche cladding
Dimension x = thickness of niche cladding material
c Worktop
d Worktop cut-out
d Minimum safety distance
for combustible materials is 50 mm
for non-combustible materials is 50 mm less dimension x
67
Hob with frame or bevelled edge
Installation notes
Tiled worktop
Seal between the hob and the
worktop
Do not use sealant between the hob
and the worktop. This could result in
damage to the hob or the worktop if
the hob ever needs to be removed
for servicing.
The sealing strip under the edge of the
top part of the appliance provides a
sufficient seal for the worktop.
68
Grout lines a and the hatched area
underneath the hob frame must be
smooth and even. If they are not the
hob will not sit flush with the worktop
and the sealing strip underneath the
hob will not provide a good seal
between the hob and the worktop.
Hob with frame or bevelled edge
Building-in dimensions
KM 6357
a Front
b Casing depth
c Connection for Miele|home
d Mains connection box
The mains connection cable (1440 mm long) is supplied separately.
69
Hob with frame or bevelled edge
KM 6379
a Front
b Casing depth
c Connection for Miele|home
d Mains connection box
The mains connection cable (1440 mm long) is supplied separately.
70
Hob with frame or bevelled edge
KM 6386
a Front
b Casing depth
c Connection for Miele|home
d Mains connection box
The mains connection cable (1440 mm long) is supplied separately.
71
Hob with frame or bevelled edge
Installing the hob
Installing the hob
Preparing the worktop
^ Feed the mains connection cable
down through the cut-out.
^ Make the worktop cut-out according
to the dimensions given in the
building-in diagram. Remember to
maintain the minimum safety
distances (see "Safety instructions
for installation").
^ Seal the cut surfaces with a suitable
heat-resistant sealant to avoid
swelling caused by moisture.
Make sure that the sealant does not
come into contact with the top of the
worktop.
^ Place the hob centrally in the cut-out.
When doing this, make sure that the
seal under the hob sits flush with the
worktop on all sides. This is important
to ensure an effective seal all round.
Do not use sealant (e.g. silicone).
If the seal does not meet the worktop
correctly on the corners the corner
radius (ß R4) can be carefully
scribed to suit.
^ Connect the hob to the mains.
^ Check that the hob works.
No spring clamps are needed to
install the hob. The seal underneath
the hob will hold it securely on the
worktop.
Any gap between the frame and
worktop will reduce with time.
Connecting the mains cable to the
appliance
The mains cable must only be
connected to the appliance by a
qualified and competent electrician
in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
^ Follow the instructions in the wiring
diagram (see "Electrical connection Wiring diagram").
72
Flush-fitted hobs
Building-in dimensions
KM 6358
a Front
b Casing depth
c Connection for Miele|home
d Stepped cut-out for granite or marble
worktops
e Mains connection box
Please take careful note of the
detailed diagrams for the cut-out
dimensions in granite and marble
worktops.
The mains connection cable (1440 mm
long) is supplied separately.
73
Flush-fitted hobs
KM 6387
a Front
b Casing depth
c Connection for Miele|home
d Stepped cut-out for granite or marble
worktops
e Mains connection box
The mains connection cable (1440 mm
long) is supplied separately.
74
Please take careful note of the
detailed diagrams for the cut-out
dimensions in granite and marble
worktops.
Flush-fitted hobs
Installing the hob
Flush fit hobs are only suitable for
installation in granite, marble, tiled or
solid wood worktops.
When using a worktop made from
any other material, please check first
with the worktop manufacturer that it
is suitable for installing a flush fit
hob.
Certain models are suitable for
building into glass worktops - please
see advice under "Building-in
dimensions".
The hob can be installed
– in a suitable cut-out in a granite or
marble worktop.
– in a suitable cut-out in a tiled or solid
wood worktop or a glass worktop
with a wooden support frame. The
frame must be provided on site, and
is not supplied with the appliance.
The internal width of the base unit
must be at least as wide as the
internal cut-out width for the hob
(see "Building-in dimensions"). This
is to ensure that the casing can be
easily removed for maintenance.
If the underside of the hob is not
freely accessible after installation,
any sealant used to plug the gaps
around the appliance must be
removed to enable the hob to be
lifted out of the cut-out should this
be necessary.
75
Flush-fitted hobs
Granite and marble worktops
Connecting the mains cable to the
appliance
Preparing the worktop
The mains cable must only be
connected to the appliance by a
qualified and competent electrician
in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
^ Follow the instructions in the wiring
diagram (see "Electrical connection Wiring diagram").
a Worktop
b Hob
c Gap
As the ceramic glass and the
worktop cut-out have a certain
dimensional tolerance, the size of
gap c can vary (min. 1 mm).
^ Make the worktop cut-out as shown
in "Building-in dimensions".
Observe the safety distances (see
"Safety instructions for installation").
Installing the hob
^ Feed the mains connection cable
down through the cut-out.
^ Centre the hob b in the cut-out.
^ Connect the hob to the mains.
^ Check that the hob works.
^ Seal the remaining gap c with a
silicone sealant that is heat-resistant
to at least 160 °C.
For granite and marble worktops,
only use silicone sealant that is
especially formulated for granite and
marble, and observe the sealant
manufacturer's instructions.
76
Flush-fitted hobs
Solid wood, tiled and glass
worktops
Preparing the worktop
a Worktop
Connecting the mains cable to the
appliance
The mains cable must only be
connected to the appliance by a
qualified and competent electrician
in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
^ Follow the instructions in the wiring
diagram (see "Electrical connection Wiring diagram").
b Hob
c Gap
d Wooden frame 13 mm
(to be provided on site)
As the ceramic glass and the
worktop cut-out have a certain
dimensional tolerance, the size of
gap c can vary (min. 1 mm).
Installing the hob
^ Feed the mains connection cable
down through the cut-out.
^ Centre the hob b in the cut-out.
^ Connect the hob to the mains.
^ Check that the hob works.
^ Seal the remaining gap c with a
silicone sealant that is heat-resistant
to at least 160 °C.
^ Make the worktop cut-out as shown
in "Building-in dimensions".
Observe the safety distances (see
"Safety instructions for installation").
Observe the silicone sealant
manufacturer's instructions.
^ Fix the wooden frame d 7 mm
below the top edge of the worktop
(see diagram).
For granite and marble tiles, only
use silicone sealant that has been
especially formulated for granite and
marble.
77
Electrical connection
All electrical work should be carried
out by a suitably qualified and
competent person, in strict
accordance with current local and
national safety regulations (BS 7671
in the UK).
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
unauthorised work.
A damaged cable must be replaced
by a suitably qualified electrician
with a special connection cable of
type H 05 VV-F, available from
Miele.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
The appliance must only be
operated when built-in. This is to
ensure that all electrical parts are
shielded. Live parts must not be
exposed.
Connection should be made via a
suitable isolator which complies with
national and local safety regulations,
and the On/Off switch should be easily
accessible after the appliance has
been built in.
If the switch is not accessible after
installation (depending on country) an
additional means of disconnection must
be provided for all poles.
For extra safety it is advisable to protect
the appliance with a residual current
device (RCD). Please contact a
qualified electrician for advice.
When switched off there must be an
all-pole contact gap of at least 3 mm in
the isolator switch (including switch,
fuses and relays).
Important U.K.
The appliance is supplied for
connection to a 230-240 V, 50 Hz
supply with a 3-core cable.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
Please make sure that the connection
data quoted on the data plate match
the household mains supply.
78
Blue
= neutral
Brown
= live
WARNING
THIS APPLIANCE MUST BE
EARTHED
Electrical connection
The electrical safety of this appliance
can only be guaranteed when
continuity is complete between it and
an effective earthing system, which
complies with current local and national
safety regulations. It is most important
that this basic safety requirement is
present and regularly tested and where
there is any doubt, the electrical wiring
in the home should be inspected by a
qualified electrician. The manufacturer
cannot be held liable for the
consequences of an inadequate
earthing system such as an electric
shock.
The manufacturer cannot be held
liable for damage which is the direct
or indirect result of incorrect
installation or connection.
Wiring diagram
a b c d e L1
L2
L3
N
200-240 V~
200-240 V~
200-240 V~
a b c d e L1
L2
N
(L3)
200-240 V~
200-240 V~
a b c d e L1
N
200-240 V~
(L2)
79
After sales service, data plate
In the event of any faults which you cannot remedy yourself, please contact:
– your Miele dealer, or
– Miele (see back cover for contact details).
Please note that telephone calls may be monitored and recorded for training
purposes (UK only).
When contacting your Dealer or Miele, please quote the model and serial number
of your appliance. These are given on the data plate.
Space in which to stick the extra data plate supplied with the appliance. Ensure
that the model number is the same as the one on the front of these instructions.
Guarantee
For information on the appliance guarantee specific to your country please
contact Miele. See back cover for contact details. In the UK, your appliance is
guaranteed for 2 years from the date of purchase. However, you must activate
your cover by calling 0845 365 6640 or registering online at www.miele.co.uk.
80
81
82
83
Alteration rights reserved / 1113
M.-Nr. 09 524 060 / 01
Download PDF
Similar pages
CDA HG6320
CDA HC3620
Smeg SE32X hob
Indesit PI 604 WH
Smeg KTS75AC cooker hood
Miele KM 400-3 Operating instructions