Always there to help you
Register your product and get support at
www.philips.com/support
Question?
Contact
Philips
User manual
AZ328
Release notes
This version has the following updates compared with V2.0 version:
• Max Output Power changes to Rated Output Power.
• Operation Power Comsumption changes to 10W.
• Dimensions changes to: 300 x 134 x 240mm.
• The weight of the product changes to 1.5 kg.
Contents
1Important
2
Safety2
Notice2
2 Your CD Soundmachine
4
Introduction4
What's in the box
4
Overview of the main unit
4
3 Get started
6
6
7
7
4Play
7
7
8
8
8
9
Connect power
Turn on
Turn off
Play a CD
Play from an external device
Play from USB devices
Play tape
Tune to FM radio stations
5 Play options
Control play
Program tracks
Adjust sound
10
10
10
10
6 Product information
11
Specifications
11
Maintenance11
7Troubleshooting
13
EN
1
1Important
•
•
Safety
•
•
•
•
•
•
•
•
•
•
•
•
2
Read these instructions.
Follow all instructions.
Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
Protect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the unit.
Only use attachments/accessories specified
by the manufacturer.
Unplug this unit during lightning storms or
when unused for long periods of time.
Recording is permissible insofar as
copyright or other rights of third parties
are not infringed upon.
Refer all servicing to qualified service
personnel. Servicing is required when the
unit has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have
fallen into the apparatus, the unit has been
exposed to rain or moisture, does not
operate normally, or has been dropped.
Battery usage CAUTION – To prevent
battery leakage which may result in bodily
injury, property damage, or damage to the
unit:
• Install all batteries correctly, + and - as
marked on the unit.
• Do not mix batteries (old and new or
carbon and alkaline, etc.).
• Remove batteries when the unit is not
used for a long time.
EN
•
Batteries (battery pack or batteries
installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
CAUTION: Danger of explosion if battery
is incorrectly replaced. Replace only with
the same or equivalent type.
The unit shall not be exposed to dripping
or splashing.
Do not place any sources of danger on
the unit (e.g. liquid filled objects, lighted
candles).
Where the MAINS plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
Warning
•• Never remove the casing of this apparatus.
•• Never place this apparatus on other electrical
equipment.
•• Never look into the laser beam inside this apparatus.
Caution
•• Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
Notice
This product complies with the radio
interference requirements of the European
Community.
Any changes or modifications made to this
device that are not expressly approved by
WOOX Innovations may void the user’s
authority to operate the equipment.
Disposal of your old product
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU. Inform yourself about the local
separate collection system for electrical and
electronic products. Follow local rules and never
dispose of the product with normal household
waste. Correct disposal of old products
helps prevent negative consequences for the
environment and human health.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
paper pulp (buffer) and polyethylene (bags,
protective foam sheet.)
This symbol indicates that the apparatus has a
double insulation system.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offence.
This equipment should not be used for such
purposes.
The USB-IF Logos are trademarks of Universal
Serial Bus Implementers Forum, Inc.
Note
•• The type plate is located on the bottom of the
apparatus.
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
This apparatus includes these labels:
Class II equipment symbol
EN
3
2 Your CD
Soundmachine
Overview of the main unit
a
e
b
f
g
h
Introduction
With this CD Soundmachine, you can:
• listen to FM radio;
• enjoy audio from discs, tapes, USB device,
and other external audio devices;
• program the play sequence of tracks.
c
d
i
j
k
p
l
q
The unit offers you Dynamic Bass Boost (DBB)
to enrich sound.
AUDIO IN
CD USB FM TAPE / OFF
What's in the box
Check and identify the contents of the package:
• Main unit
• Power cord
• Short User Manual
• Safety sheet
m
n
o
a DBB
• Turn dynamic bass boost on/off.
•
Stop playing.
b - ALBUM +
• Skip to the previous or next album.
c
/
• Skip to the previous or next track.
• Search within a track.
d OPEN•CLOSE
• Open or close the disc compartment.
e Tape controls
•
Start tape play.
•
/
Fast rewind or fast forward the tape.
Stop the tape play or open the tape
door.
•
Pause tape play.
4
EN
f
• Start or pause play.
• Press to wake up the unit from
standby mode.
g PROG
• Program the play sequence of tracks.
h MODE
• Select a play mode.
i Display panel
• Display current status.
j FM antenna
• Improve FM reception.
k + TUNING • Tune to FM radio stations.
l
• USB socket.
m Source selector
• Select a source.
n + VOLUME • Adjust volume
o AC~MAINS
• Power supply socket.
p AUDIO-IN
• Connect an external audio device.
EN
5
3 Get started
Caution
•• Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
AC~MAINS
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of your apparatus. The
model number and serial number are on the
bottom of your apparatus. Write the numbers
here:
Model No. __________________________
Option 2: Battery power
Caution
•• Batteries contain chemical substances, so they should
be disposed of properly.
Serial No. ___________________________
Note
Connect power
The unit can be powered by either AC power
or batteries.
•• Batteries are not supplied with the accessories.
1
2
Open the battery compartment.
3
Close the battery compartment.
Option 1: AC power
Warning
•• Risk of product damage! Make sure that the power
supply voltage corresponds to the voltage printed on
the back or the underside of the unit.
•• Risk of electric shock! When you disconnect the AC
power, always pull the plug from the socket. Never pull
the cord.
Connect the AC power cord to the wall socket.
Tip
•• To save energy, turn the unit off after use.
6
EN
Insert 6 batteries (type: 1.5V R14/UM2/C
CELL) with correct polarity (+/-) as
indicated.
Turn on
4Play
Switch the source selector on the main unit to
FM/USB/AUDIO-IN/CD.
»» When the source selector is in the
AUDIO-IN/CD position, CD is
displayed.
Play a CD
Switch to standby mode
• The unit switches to standby mode
automatically when there is no audio
detected for over 15 minutes.
• Press
to wake up the unit from
standby mode.
Turn off
Switch the source selector on the main unit to
OFF.
Note
•• You cannot play CDs encoded with copyright
protection technologies.
•• When an audio-in cable is plugged, CD/USB playback
stops, and the unit switches to audio in mode
automatically.
You can play commercially available audio CDs:
• CD-Recordables (CD-R)
• CD-Rewritables (CD-RW)
• MP3-CDs
1
2
3
•
•
•
•
Switch the source selector to CD.
Open the CD compartment.
Insert a CD with the printed side facing up
and close the CD lid gently.
»» The total number of tracks displays.
»» Your CD sound machine starts to play
automatically.
To select a track,press
/ .
To pause CD play, press
.
»» [ ] and track number flash.
To resume CD play, press
again.
To stop CD play, press .
AUDIO IN
CD USB FM TAPE / OFF
EN
7
Play from an external device
You can also listen to an external audio device
through this unit.
1
Switch the source selector to AUDIO-IN/
CD.
2
Connect an audio cable (3.5mm, not
supplied) to:
• the AUDIO-IN socket on the unit.
• the headphone socket on an external
device.
3
Play the external device (see the device's
user manual).
AUDIO IN
CD USB FM TAPE / OFF
Note
•• The AUDIO-IN socket is not for headphones.
•• The display panel lights off when the unit plays from the
external device and "ÄU" displays on the screen.
Play tape
AUDIO-IN
Play from USB devices
Note
•• Make sure that the USB device contains playable audio
content.
1
2
Slide the source selector to TAPE.
3
Load the tape with the open side upward
and the full spool to the right.
4
Press on main unit to start play.
• To pause/resume play, press on main
unit .
• To rewind or fast-forward, press
/
on main unit .
• To stop play, press
.
Press
door.
on main unit to open the tape
Note
•• In playback mode, cassette will be stopped
1
2
Switch the source selector to USB.
8
EN
Insert the USB device into the
socket.
»» Play starts automatically. If not, press
.
automatically when playback reaches the end.
AUDIO IN
CD USB FM TAPE / OFF
Tune to FM radio stations
Note
•• For optimal reception, fully extend and adjust the
position of the FM antenna.
1
2
3
Switch the source selector to FM.
Rotate TUNING to select a station.
Repeat step 2 to tune to more stations.
AUDIO IN
CD USB FM TAPE / OFF
EN
9
5 Play options
Program tracks
In CD and USB mode, you can program a
maximum of 20 tracks.
Control play
In CD mode, you can control play through the
following operations.
/
Press:skip to the previous/next
track
PROG
+VOLUME- ALBUM +
MODE
Hold:search within play, then
release to resume play.
Start or pause play.
Stop play.
Program tracks.
Adjust volume.
Skip the the previous or next
album.
Select a play mode.
[ ]: Play the current track
repeatedly.
[
]: Play all tracks
repeatedly.
[
]: Repeat all tracks
randomly.
To return to normal play, press
MODE repeatedly until the
repeat icons disappear.
Tip
•• Only[
] and [
] can be selected when you
play the programmed tracks.
10
EN
1
2
Press
3
Press
/
to select a track number,
then press PROG to confirm.
4
5
Repeat steps 3 to program more tracks.
to stop playback.
Press PROG to activate the program
mode.
»» [PROG] (program) begin to blink.
Press
to play the programmed tracks.
»» During play, [PROG] (program) is
displayed.
• To erase the program, press
twice.
Adjust sound
During play, you can adjust volume and select
the sound effects.
Key
+VOLUMEDBB
Function
Increase or decrease volume.
Turn dynamic bass
enhancement on or off.
6Product
information
Note
•• Product information is subject to change without prior
Tape deck
Frequency response
125 - 8000
Hz (8 dB)
- Normal tape (type I)
Signal-to-noise ratio
35 dBA
- Normal tape (type I)
Wow and flutter
≤ 0.4%
DIN
notice.
General
Power supply
Specifications
Amplifier
Rated Output Power
Frequency Response
Signal to Noise Ratio
Total Harmonic Distortion
Audio-in Input
2x 1 W RMS
125 -16000
Hz, -3dB
>55 dBA
<1 %
650 mV RMS
Disc
Laser Type
Disc Diameter
Support Disc
Audio DAC
Total Harmonic
Distortion
Frequency Response
S/N Ratio
Semiconductor
12cm/8cm
CD-DA, CD-R, CDRW, MP3-CD
24Bits / 44.1kHz
<1%
125 -16000 Hz, -3dB
>55 dBA
Tuner
Tuning Range
Total Harmonic Distortion
Signal to Noise Ratio
87.5 108MHz
<3%
>50 dBA
- AC Power
220-240V~, 50/60 Hz;
- Battery
DC 9 V, 6 x 1.5 V
type: R14/UM2/C
CELL
10 W
Operation Power
Consumption
Standby Power
Consumption
Dimensions
<0.5 W
- Main Unit
300 x 134 x 240 mm
(W x H x D)
Weight (Main Unit)
1.5 kg
Maintenance
Clean the cabinet
• Use a soft cloth slightly moistened with
a mild detergent solution. Do not use a
solution containing alcohol, spirits, ammonia
or abrasives.
Clean discs
• When a disc becomes dirty, clean it with
a cleaning cloth. Wipe the disc from the
centre out.
EN
11
•
Do not use solvents such as benzene,
thinner, commercially available cleaners,
or antistatic spray intended for analogue
records.
Clean the disc lens
• After prolonged use, dirt or dust may
accumulate at the disc lens. To ensure good
play quality, clean the disc lens with Philips
CD lens cleaner or any commercially
available cleaner. Follow the instructions
supplied with cleaner.
Clean the heads and the tape paths
• To ensure good recording and play quality,
clean the heads A, the capstan(s) B, and
pressure roller(s) C after every 50 hours
of tape operation.
• Use a cotton swab slightly moistened with
cleaning fluid or alcohol.
•
You can also clean the heads by playing a
cleaning tape once.
Demagnetise the heads
• Use a demagnetising tape available at your
dealer.
12
EN
7Troubleshooting
Warning
•• Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
••
••
••
Wait until the moisture condensation at
the lens has cleared.
Replace or clean the disc.
Use a finalized CD or correct format disc.
Poor radio reception
•• Increase the distance between the unit and
your TV or VCR.
•• Fully extend the FM antenna.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support). When you contact Philips,
make sure that the device is nearby and the
model number and serial number are available.
No power
• Ensure that the Mains cord is connected
securely.
• Ensure that there is power at the AC
Mains.
• Ensure that the batteries are inserted
correctly.
No sound or poor sound
•• Adjust the volume.
No response from the unit
•• Disconnect and reconnect the AC power
plug, then turn on the system again.
•• As a power-saving feature, the unit
switches off automatically 15 minutes after
track play reaches the end and no control
is operated.
Poor cassette sound quality
• Ensure that heads in the cassette holder
are clean.
• Ensure that a NORMAL (IECI) cassette
tape is used for record.
Cassette does not work for record
• Ensure that cassette tabs are not broken.
No disc detected
•• Insert a disc.
•• Check if the disc is inserted upside down.
EN
13
Specifications are subject to change without notice
2014 © WOOX Innovations Limited. All rights reserved.
Philips and the Philips’ Shield Emblem are registered trademarks of Koninklijke Philips N.V. and
are used by WOOX Innovations Limited under license from Koninklijke Philips N.V.
AZ328_12_UM_V3.0