Siemens WM14Y591GB washing machine

Washing machine
WM14Y591GB, WM16Y591GB
siemens-home.com/welcome
en :DVKLQJPDFKLQH
,QVWUXFWLRQ0DQXDODQG,QVWDOODWLRQ,QVWUXFWLRQV
Register
your
product
online
Your new washing machine
You have chosen a Siemens washing machine.
Please take a few minutes to read and become familiar with the
advantages of your washing machine.
To meet the high quality demands required by Siemens, every
washing machine that leaves our factory is carefully checked to
ensure that it functions correctly and is in perfect condition.
For more information on our products, accessories, replacement
parts and services, see our website www.siemens-home.com or
contact our after-sales service centres.
If the operating and installation instructions describe different
models, any differences will be pointed out at the relevant points
in the text.
Read these operating and installation instructions before
switching on the washing machine.
Display rules
m Warning!
This combination of symbol and signal word indicates a possibly
dangerous situation. Not heeding the warning can cause death
or injuries.
m Caution!
This signal word indicates a possibly dangerous situation. Not
heeding the caution can cause property and/or environmental
damage.
²
Information about the optimum use of the appliance/any other
useful information.
1. 2. 3. / a) b) c)
The steps are represented by numbers or letters.
Ø /Lists are represented by a small box or a dash.
2
Contents
enWashgi
macnheiuoIrst
Manul
and
Before washing
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Intended use
Safety instructions
Protection of the environment
The main points in brief
Getting to know your appliance
Detergent drawer
Operating elements/Display elements
Operating the appliance
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Before each washing
Washing
After washing
Programme overview
Programme settings
Consumption values
Appliance settings
Sensors – Your washing machine is so intelligent
Cleaning and maintenance
Ø
Ø
Ø
Ø
Ø
Care and maintenance
Emergency release
Information on the display panel
Faults, what to do?
Customer service
Installing the appliance
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Index
Standard accessories
Installation
Remove transportation protection devices
Connecting the water
Alignment
Electrical connection
Before the 1st washing
Transportation, e.g. if moving house
oanitlIs
nuoIrscti
4
5
7
8
9
10
11
12
18
21
22
26
28
29
30
31
35
36
37
39
40
42
45
47
50
51
52
53
54
3
Intended use
Beofr
Ø For use in the household only.
Ø The washing machine is suitable for washing machine-
washable textiles and hand-washable wool in wash liquor.
Ø The washing machine is suitable to be operated with cold
drinking water and commercially available detergents and
care products which are suitable for use in washing
machines.
Ø When dosing all detergents, cleaning aids, cleaning products
and cleaning agents, always follow the manufacturer's
instructions.
Ø The washing machine may be operated by children from 8
years of age, by persons who have limited physical, sensory
or mental abilities and by persons who have inadequate
experience or knowledge, provided they are supervised or
have been instructed by a responsible person.
Ø Keep pets away from the washing machine!
Read and follow the operating and installation instructions and all
other information enclosed with the washing machine.
Retain documents for subsequent use.
4
wasnhgi
Safety instructions
m Warning!
Danger of death from electric shock!
Danger of death if live parts are touched.
– Never pull out the mains plug by tugging the power cord.
– Insert/pull out the mains plug with dry hands only.
m Warning!
Risk to children!
– Do not leave children unsupervised near the washing machine.
– Children must not play with the washing machine.
– This will prevent children from locking themselves in and
suffocating.
On redundant appliances:
– Pull out the mains plug!
– Sever the power cord and discard together with the plug.
– Destroy the lock on the washing-machine door.
– Children must not perform any cleaning or maintenance work
without supervision.
– When playing, children may become entangled in the
packaging/film and packaging parts or pull them over their
heads and suffocate.
Keep packaging, plastic film and packaging parts out of the reach
of children.
– When washing at high temperatures, the glass of the washing
machine door becomes hot.
Prevent children from touching the hot washing machine door.
– Detergents and care products may cause intoxication if
consumed or eye and skin irritation if touched.
Keep detergents and care products out of the reach of children.
m Warning!
Risk of explosion!
Items of washing pretreated with solvent detergents, e.g. stain
remover/petroleum ether, may cause an explosion when the
washing machine has been loaded.
Before hand thoroughly rinse items of washing by hand.
5
m Caution!
Danger of scalding!
When washing at high temperatures, you may be scalded if you
touch the hot wash liquor (e.g. if draining hot wash liquor into a
washbasin or if draining the washing machine in an emergency).
Allow detergent solution to cool down.
m Caution!
Risk of damaging appliance!
– Cover plate may break!
Do not climb on the washing machine.
– Opened washing machine door may break off or washing
machine may overturn!
Do not lean on the open washing machine door.
m Caution!
Danger when reaching into/gripping the rotating drum!
If you reach into the rotating drum, you may injure your hands.
Do not grip the rotating drum. Wait until the drum stops rotating.
m Caution!
Risk of coming into contact with liquid detergents/care products!
If the detergent drawer is opened while the washing machine is
running, detergent/care product may spray out.
Caution when opening the detergent drawer.
In case of eye/skin contact, rinse thoroughly.
If accidentally swallowed, seek medical advice.
6
Protection of the environment
Packaging/Old appliance
)
Dispose of packaging in an environmentally friendly manner.
This appliance is labelled in accordance with European Directive
2012/19/EU concerning used electrical and electronic
appliances (waste electrical and electronic equipment - WEEE).
The guideline determines the framework for the return and
recycling of used appliances as applicable throughout the EU.
Hints and tips
Ø Utilise the maximum amount of washing for the particular
programme.
Ø Wash normally soiled washing without Pre-wash.
Ø Energy saving mode: The display panel light goes out after
several minutes, Start/Reload Ü flashes. To activate the
light, select any button.
The energy-saving mode is not activated if a programme is
running.
Ø The selectable temperatures apply to the care labels on the
textiles. The temperatures in the machine may deviate from
this so that you get the optimum mix of energy-saving and
washing results.
Ø Automatic switch off: If the appliance is not operated for a
prolonged period, it automatically switches off before the
programme starts and when the programme has ended to
save energy. Switch on by pressing main switch # button.
Ø If the washing is then dried in the tumble dryer, select spin
speed according to the instructions of the dryer
manufacturer.
7
The main points in brief
1
@
Insert mains plug.
Turn the tap on.
2
@
Open the washing
machine door.
@
Sort the washing.
3
@
To switch on, press
the # button.
Select the
programme, e.g.
Cotton.
@
Insert the washing.
Do not exceed maximum load.
@
@
FODFN
4
Open the detergent
drawer.
Dose detergent according to dosing
recommendation.
Close the washing
machine door.
@
If required, change presettings of the selected programme and/or select
programme settings.
5
@
End of the programme
8
Select
Start/Reload Ü.
@
For switching the
machine on, press
the # button.
Turn off the mains
supply (for models
without Aqua-Stop).
Getting to know your appliance
2SHUDWLQJ
HOHPHQWV
'LVSOD\
HOHPHQWV
'HWHUJHQWGUDZHU
'UXPOLJKW
GHSHQGLQJ
RQPRGHO
'RRU
6HUYLFHIODS
FODFN
2SHQLQJ
DQGFORVLQJWKHGRRU
6HUYLFHIODS
9
Detergent drawer
Dispenser I
Dispenser i
Dispenser II
Insert A
Detergent for prewash
Softener, starch. Do not exceed the maximum load.
Detergent for main wash, water softener, bleach, stain
remover
for dosing liquid detergent (not for all models)
For models with insert for liquid detergent:
The detergent drawer features an insert which is used as a dosing aid for liquid detergent.
².Do not use insert:
– For gel-like detergents and washing powders.
– For programmes with Prewash or Ready in option.
Position insert for dosing liquid detergent:
Completely remove detergent drawer.
Push insert forwards.
For models without insert for liquid detergent:
Dose liquid detergent according to the manufacturer’s instructions.
10
Operating elements/Display elements
LM
V
N
O
P
Q
R
S
T KU
² All buttons are sensitive, they only need to be touched gently.
i Press the main switch # button. Switch h Change appliance settings. Hold down
on and off the appliance.
Basic Settings 3 sec buttons for
appliance settings (end signal, button
signal, language, autom. switch off) for
in either direction. Programme overview
approx. 3 seconds. Overview of all
refer to ~ Page 22
settings ~ Page 29
r Temperature selection, Select spin
Programme settings:
speed, End time preselection button
~ Page 15, ~ Page 22
~ Page 26
k ecoPerfect ¦
s
Display
panel for settings and
l speedPerfect G
information.
m Less Ironing {
n Prewash !
o Extra Rinse «
p Rinse Hold $
q Start/Reload Ü button to start, interrupt
and cancel the programme
(e.g. Topping up the washing).
j Programme selector can be rotated
11
Before each washing
Opneagirt
²
hte
– Install and connect washing machine properly. Refer
to ~ Page 42
– Before the 1st wash, wash once without any washing.
~ Page 52
1. Preparing the washing
Sorting the washing according to:
Ø Type of fabric/fibre.
Ø Colour.
Ø Soiling.
Ø Follow manufacturer’s care information.
Ø Care label specifications:
<;
:98
B A>
AL>
K
WAL
>K
Ž
Cotton 95 °C, 90 °C
Coloureds 60 °C, 40 °C, 30 °C
Easy-Care 60 °C, 40 °C, 30 °C
Delicates 40 °C, 30 °C
Hand and machine-washable silk and woollens cold, 40 °C,
30 °C
Do not wash laundry in the washing machine.
Protecting the washing and the machine:
²
12
– When dosing all detergents, cleaning aids, cleaning products
and cleaning agents, always follow the manufacturer's
instructions.
– Keep detergents and agents for the pretreatment of washing
(e.g. stain remover, prewash sprays, ...) away from the
surfaces of the washing machine. Using a damp cloth,
immediately remove any fine spray residue and other
residue/droplets.
– Empty pockets.
– Remove metal parts (paper clips, etc.).
– Wash delicates in the net/bag (tights, underwired bras).
– Close zips, button up covers.
– Brush sand out of pockets and collars.
– Remove curtain fittings or include in the net/bag.
– Wash new items separately.
apnicle
2. Preparing the appliance
Insert mains plug.
Turn on water tap.
3. Selecting programme and loading laundry in the drum
1. Open the washing machine door.
2. Check whether the drum has been completely emptied. If
required, empty. Otherwise, the load display may malfunction.
~ Page 30
3. Press the # button. The appliance is switched on.
Then always the Cotton programme preset at the factory is
displayed.
Displays for the Cotton programme:
– The indicator lamp is lit on the programme selector and
the main menu for the selected programme is indicated
on the display panel.
– For appliances with drum light:
After switching on the appliance, after opening and
closing the washing machine door as well as after starting
the programme, the drum is lit. The light goes out
automatically.
13
4. Select the programme.
You can use the displayed programme
or select another programme. Programme overview, refer to
~ Page 22
5. Insert laundry
The load screen for the selected programme (e.g. for Cotton) is
indicated on the display panel. The load screen is indicated
when the door is opened or when the amount of washing
is changed.
²
– Unfold and load presorted items of washing. Mix large and
small items. Washing items of different size distribute
themselves better during the spin cycle. Individual items
of washing may cause an unbalanced load. ~ Page 30
– Do not load the laundry until the main menu for the
programme is displayed.
– The load bar progresses as the washing machine is loaded.
If the max. load is exceeded, the bar flashes. Do not exceed
indicated max. load. Overfilling reduces the washing result
and encourages creasing.
4. Add detergent and fabric care product
1. Pull out the detergent drawer.
2. Dosing in dispenser ~ Page 10 according to:
– Dosage recommendation on the display panel,
e.g. for Cotton:
Depending on the amount of washing in the washing
machine, a dosing recommendation is indicated on the
display panel. The indicated % refers to the dosage
recommendation of the detergent manufacturer.
2 = 40 % of the recommendation of the detergent
manufacturer
14
3 = 60 %
4 = 75 %
5 = 100 %
– Soiling,
– Water hardness (depending on model can be determined
using enclosed water hardness strip or is available from
your water utility company).
– Manufacturer’s instructions.
²
– When dosing all detergents, cleaning aids, cleaning products
and cleaning agents, always follow the manufacturer's
instructions.
– Dilute viscous fabric softener and fabric conditioner with
water.
Prevents blockage of the overflow!
5. Changing programme settings
Take care not to trap any items of clothing between the loading
door and rubber seal.
Close the washing machine door.
FODFN
The main menu for the selected programme is indicated again
on the display panel.
You can use the displayed presettings or adjust the selected
programme optimally to the items of washing by changing the
presettings or selecting additional settings.
15
Ø Change presettings for temperature, spin speed, finished in
time; ,
E.g. select and change Temp. °C buttons – and +:
The settings are active without acknowledgement and are
displayed in the main menu.
²
– If the buttons are held down, the set values automatically run
through (– downwards, + upwards).
– The respective programme duration is displayed by selecting
the programme. The programme duration is adjusted while
the programme is running if the programme duration requires
changing, e.g. due to changes in the programme settings,
foam detection, unbalanced load detection, the load
or soiling.
Ø Select addition programme settings:
~ Page 22, ~ Page 26
– ecoPerfect ¦
Energy-optimised washing by reducing the temperature
while achieving a consistent washing result. When
selected, the display lamp is lit.
– speedPerfect G
For a shorter wash time with a comparable washing effect
to the standard programme. Observe maximum load.
~ Page 22
When selected, the display lamp is lit.
²
16
The washing temperature is lower than the selected
temperature. For special hygiene requirements, the
Hygiene programme is recommended. ~ Page 24
Other settings can be selected depending on the model,
e.g. Rinse Hold $ button:
When selected, the button indicator lamp is lit and
a corresponding symbol is indicated on the display panel:
Button Less Ironing – {
Button Prewash – !
Button Extra Rinse – « + Ë, Ì, Í (Rinse cycles)
Button Rinse Hold – $
6. Starting the programme
Ø Select Start/Reload Ü. The indicator light is on.
17
Washing
Programme sequence
While the programme is running, the programme progress
is indicated on the display panel via corresponding symbols and
a progress bar. The bar progresses in the course of the wash
cycles.
The combined symbol Æ indicates the following programme
states:
¿ Pre-wash
¼ Wash
½ Rinse
¾ Drain
Other symbols:
0 Spin
w Childlock has been activated
Å Overdosage of the detergent detected, additional rinse
cycles activated.
Ä is lit when the door is locked or unlocked.
During the washing
Ø Childlock
To prevent the set functions of the washing machine from
being accidentally changed, the childproof lock
can be activated when the programme has started.
Activate/deactivate: press Finish in for approx. 5 seconds.
18
The activated childproof lock is indicated on the display
panel by the symbol w.
If the programme selector is adjusted or a button is selected
while the childproof lock is active, the w symbol flashes
briefly.
Ø Topping up laundry
When the programme has started, washing can be reloaded
or taken out as required.
Select Start/Reload Ü.
²
– If there is a high water level, high temperature or if the drum
is rotating, the washing machine door remains locked for
reasons of safety and reload is not possible. Follow the
information on the display panel. To continue the programme,
select the Start/Reload Ü button. The washing machine
door is locked and the programme continues automatically.
– Load display is not active during reloding.
– Do not leave washing machine door open for a prolonged
period – water could run out of the washing.
Ø Changing the programme
if you have mistakenly started a wrong programme.
1. Select Start/Reload Ü.
2. Select another programme.
3. Select Start/Reload Ü. The new programme starts from
the beginning.
Ø Cancelling the programme
For programmes at high temperature:
1. Select Start/Reload Ü.
2. Cool down laundry: select Rinse.
3. Select Start/Reload Ü.
For programmes at low temperature:
1. Select Start/Reload Ü.
2. Select Spin or Empty.
3. Select Start/Reload Ü.
19
Ø End of programme by Rinse Hold $. Programme stops
in the last rinse cycle.
– Select Start/Reload Ü. The programme continues with
the drain and spin cycles (if required change spin speed).
– If only the drain cycle, but not the spin cycle, is required,
select and start the Empty programme.
End of the programme
FINISHED is indicated on the display panel.
If the symbol Å is also indicated on the display panel,
the washing machine has detected too much foam during the
wash programme and therefore automatically activates additional
rinse cycles to eliminate the foam.
²
20
Dose less detergent in the next wash cycle with the same load.
After washing
1. Open washing machine door and remove washing.
²
– Do not leave any items of washing in the drum. In the next
wash they may shrink or discolour something else.
– Remove any foreign objects from the drum and the rubber
seal – risk of rust.
– Leave detergent drawer and door open so that residual water
can evaporate.
Before switching the machine off:
²
– Always remove the washing. Otherwise, the load display may
malfunction.
– Always wait until the programme ends, as the appliance
could still be locked. Then switch the appliance on and wait
for the unlocking device.
2. Press the # button. Appliance is switched off.
3. Turn off the tap.
Not required for Aqua-Stop models. ~ Page 56
21
Programme overview
The presettings
of the programmes are
highlighted in bold.
Õ
Programme/Type of washing
Settings/Information
Name of the programme
Brief explanation of the programme and
for which textiles it is suitable.
max. load
selectable temperature as °C
selectable spin speeds in rpm,
the max. spin speed and
the presetting depends on the
model
possible programme settings
at the “anti-crease” programme
setting: possible spin speeds
in rpm
Cotton
Hard-wearing textiles, heat-resistant
textiles made of cotton or linen.
².* reduced load for speedPerfect G
option ~ Page 16
max. 8 kg/5 kg*
cold - 60 - 90 °C
0 ... 1400 ... 1600 rpm
¦,G,{,!,«,$
at {: 0 ... 800 rpm
Easy-Care
Textiles made of synthetic materials
or blended fabrics.
max. 4 kg
cold - 40 - 60 °C
0 ... 1200 rpm
¦,G,{,!,«,$
at {: 0 ...600 ...800 rpm
Mixed Fabrics
Mixed load consisting of textiles made
of cotton and synthetics.
max. 4 kg
cold - 40 °C
0 ... 1400 ... 1600 rpm
¦,G,{,!,«,$
at {: 0 ... 600 ... 800 rpm
22
The presettings
of the programmes are
highlighted in bold.
Programme/Type of washing
Settings/Information
Delicates/Silk
For delicate, washable textiles, e.g. made
of silk, satin, synthetic fibres or blended
fabrics (e.g. silk blouses, silk scarf).
max. 2 kg
².For machine wash use detergent
¦,G,{,!,«,$
suitable for delicates or silk.
at {: 0 ... 600 rpm
: Wool
max. 2 kg
Hand or machine-washable wool or richwool textiles.
Especially gentle wash programme
to prevent shrinkage, longer programme
pauses (textiles rest in wash liquor).
cold - 30 - 40 °C
0 ... 600 ... 800 rpm
cold - 30 - 40 °C
0 ... 800 rpm
$
².Wool is of animal origin, e.g.: angora,
alpaca, lama, sheep.
².For machine wash use detergent
suitable for wool.
Rinse
Extra rinse with spin.
0 ... 1200 ... 1600 rpm
{,«,$
at {: 0 ... 800 rpm
Spin
Extra spin with selectable spin speed.
0 ... 1200 ... 1600 rpm
{
at {: 0 ... 800 rpm
Low Spin
Extra spin cycle at reduced speed and with
especially gentle spin mechanism.
0 ... 800 ... 1200 rpm
{
at {: 0 ... 600 rpm
23
The presettings
of the programmes are
highlighted in bold.
Programme/Type of washing
Settings/Information
Empty
the rinsing water, e.g. after Flot $ (Rinse
Hold) (without final spin cycle).
-
Dark Wash
Dark textiles made of cotton and dark
easy-care textiles.
Wash textiles inside out.
max. 3,5 kg
cold - 30 - 40 °C
0 ... 800 ... 1200 rpm
¦,G,{,!,«,$
at {: 0 ... 600 ... 800 rpm
Rapid 15’
Extra short programme approx.
15 minutes, suitable for lightly soiled
washing as a small amounts of laundry.
max. 2 kg
cold - 30 - 40 °C
0 ... 800 ... 1200 rpm
$
Hygiene
Hard-wearing textiles made of cotton or
linen.
².Especially suitable for increased
hygienic demands or particularly sensitive
skin on account of prolonged washing at a
defined temperature, with a higher water
level and longer rinsing cycle.
max. 7,5 kg/5 kg*
cold - 60 °C
0 ... 1200 ... 1600 rpm
¦,G,{,!,«,$
at {: 0 ... 800 rpm
².* reduced load for speedPerfect (
option ~ Page 16
Shirts/Blouses
Non-iron shirts/blouses made of cotton,
linen, synthetics fibres or blended fabrics.
For the Less Ironing { option, shirts/
blouses are given a short spin only,
hang up dripping wet.
~ Self-smoothing effect.
².Wash shirts/blouses made of silk/
delicate materials in the Delicates/Silk
programme.
24
max. 2 kg
cold - 40 - 60 °C
0 ... 800 rpm
¦,G,{,!,«,$
at {: 0 ... 400 rpm
The presettings
of the programmes are
highlighted in bold.
Programme/Type of washing
Settings/Information
Textile Guard
Washing followed by water proofing
of weatherproof and outdoor clothing with
membrane coating and water-resistant
textiles.
max. 1 kg
².Use special detergents suitable for
cold - 30 - 40 °C
0 ... 800 rpm
¦,G,«
machine wash. Dosage according to
manufacturer’s instructions.
– Pour into dispenser II special detergent
and
– textile guard agent (max. 170 ml) into
dispenser M.
².The laundry must not be treated with
fabric softener.
².Before washing, remove all fabric
softener residue from detergent drawer (all
dispensers).
Starching
²
The washing should not be treated with fabric softener.
Liquid starch can be used in all wash programmes. Pour starch
into the dispenser M according to manufacturer’s specifications
(if required clean beforehand).
Dyeing/Discolouring
Dye in household quantities only. Salt may attack stainless
steel!Observe specifications of the dye manufacturer! Do not
discolourwashing in the washing machine!
Soaking
Pour soaking agent/detergent into dispenser II according to the
manufacturer’s instructions. Set programme selector
to Cotton 30 °C and select Start/Reload Ü. After approx.
10 minutes select Start/Reload Ü. After the required soaking
time reselect Start/Reload Ü, if the programme is to be
continued or change the programme.
²
Insert washing of the same colour. No additional detergent
required, the soaking solution is used for washing.
25
Programme settings
Depending on the programme, you can use the programme
settings to adjust the washing process even more efficiently
to your items of washing.
Programme settings:
²
– are active without acknowledgement.
– not retained after appliance is switched off.
– can be selected or deselected or changed depending
on the programme progress.
Buttons
Notes
–Temp. °C +
– Spin +
– Finish in +
Before and during the programme the presettings
can be changed depending on the programme
progress. ~ Page 16
Maximum spin speed depends on the programme
and model.
Delays the Finished in time (end of programme).
Before the programme starts, the end of the
programme can be preselected in h steps
up to maximum 24h.
When the programme has started, the preselected
time is displayed e.g. for 8h and counts down until
the wash programme starts. Then the programme
duration is displayed, e.g. 2:30h.
When the programme has started, the preselected
time can be changed as follows:
1. Select Start/Reload Ü.
2. Select Finish in button and change Finish in time.
3. Select Start/Reload Ü.
Finish in +
To activate/deactivate the Childlock ~ Page 18
ecoPerfect ¦
For saving energy. ~ Page 16
speedPerfect G
For a shorter wash time. ~ Page 16
Less Ironing
Reduces creasing by special spin sequence followed
by fluffing and reduced spin speed.
².Residual moisture of the washing is slightly
increased.
26
Buttons
Notes
Prewash
For heavily soiled washing.
Pour detergent into dispensers I and II.
Extra Rinse
« + 1 Rinse
« + 2 Rinses
« + 3 Rinses
Additional rinse cycles depending on the
programme, prolonged programme duration.
Rinse Hold
².Recommended application: for particularly
sensitive skin and/or in areas with very soft water.
The washing remains in the water after the last rinse
cycle. End the programme. ~ Page 20
27
Consumption values
Programme
Load
Energy
consumption **
Water **
Programme
duration **
Cotton 20 °C
8 kg
0,25 kWh
57 l
2^ h
Cotton 40 °C
8 kg
1,09 kWh
57 l
2_ h
Cotton 60 °C
8 kg
1,43 kWh
57 l
2_ h
Cotton 90 °C
8 kg
2,40 kWh
69 l
2^ h
Easy-Care 40 °C
4 kg
0,65 kWh
46 l
2 h
Mixed Fabrics
4 kg
0,59 kWh
44 l
1] h
Delicates/Silk
2 kg
0,15 kWh
34 l
_h
Wool 30 °C
2 kg
0,19 kWh
39 l
_h
Programme
Additonal function
Load
Annual energy
consumption
Annual water
consumption
Cotton û ú
ü ecoPerfect *
8/4 kg
137 kWh
10120 l
*
Programme setting for testing and energy labelling according to directive 2010/30/EU
with cold water (15 °C).
** The values may deviate from the stated values depending on water pressure and
hardness, room temperature, type and amount of laundry, detergents used, fluctuations
in the mains voltage and selected additional functions.
28
Appliance settings
The Basic Settings 3 sec. buttons (Spin + and Finished in +) can
be used to change the set values of the appliance settings, e.g.
the volume of the button signals.
Simultaneously hold down Basic Settings 3sec. buttons
for approx. 3 seconds:
Ø The access menu for changing the appliance settings
appears on the display panel.
Ø The – Finished in + button can be used to change the set
values.
If the buttons are held down, the set values automatically run
through.
Ø The – Spin + button can be used to select other settings.
If the buttons are held down, the settings automatically run
through.
Ø To end the settings, wait or hold down the
Basic Settings 3 sec. buttons again.
²
Settings are retained after appliance is switched off.
Settings
Set values
Notes
´½³ ¸¶½°»
Ê = off
Ë = quiet
Ì = medium
Í = loud
Î = very loud
Adjust volume of the end signal.
±ÄÃþ½ ¸¶.
Ê = off
Ë = quiet
Ì = medium
Í = loud
Î = very loud
Adjust volume of the button signals.
»°½¶Ä°¶´
³´ = German
¶± = English
...
Change displayed language.
°Äþ ¾μμ
ËÏ (min.)
ÍÊ (min.)
Ë:ÊÊ (h=hour)
¾μμ
The appliance automatically switches off after
the selected time (=0 kWh energy
consumption). to switch on, press main switch
button # .
29
Sensors – Your washing machine is so
intelligent
Load adjust
Depending on the type of textile and load, the load adjust
optimally adjusts the water consumption in each programme.
Aqua-Sensor depending on model
During the rinse cycle the Aqua sensor checks the degree
of turbidity (turbidity is caused by dirt and detergent residue)
of the rinsing water. The duration and the number of rinse cycles
depend on the turbidity of the water.
Load sensor/Load display
The load sensor detects the load level in the washing machine
when the door is open. This is indicated by a progressing bar on
the display panel.
²
To ensure that the load sensor measures all the laundry, the drum
must be empty before the washing machine is switched on.
Dosing recommendation
A detergent dosage recommendation is displayed depending
on the selected programme and the detected load. ~ Page 14
²
By observing the recommended dosage, you will protect
the environment and reduce your household costs.
Unbalanced load detection system
The automatic unbalanced load detection system spins the
laundry several times to ensure even distribution.
For reasons of safety the speed is reduced or does not perform
a spin cycle if the washing is very unevenly distributed.
²
30
Distribute small and large items of washing in the drum. Faults,
what to do? ~ Page 37
Care and maintenance
Cealngi
and
mnaetic
m Warning!
Danger of death from electric shock!
Danger of death if live parts are touched.
Switch off the appliance. Pull out the mains plug!
m Caution!
Fire and explosion hazard!
If solvent cleaning agents, e.g. petroleum ether, are
used in the washing machine, components may be
damaged and toxic fumes generated.
Do not use solvent-based cleaning agents.
m Caution!
Washing machine may be damaged!
If solvent cleaning agents, e.g. petroleum ether, are
used on the washing machine, the surfaces may be
damaged.
Do not use solvent-based cleaning agents.
Machine housing/Control panel
Ø Remove detergent residue immediately.
Ø Wipe with a soft, damp cloth.
Ø Do not clean the appliance with a water jet.
Drum
Use chlorine-free cleaning agent, not steel wool.
If there is an odour in the washing machine, run Cotton 90 °C
programme. Use standard detergent.
Descaling
Not required if detergent dosed correctly. However, if this does
occur, follow the instructions of the descaling agent
manufacturer. Suitable descalers can be purchased on our
website or from customer service. ~ Page 39
31
Cleaning the detergent drawer
If it contains detergent or fabric softener residue:
1. Pull out, depress insert, take out drawer all the way.
2. Take out insert: using your finger, press insert upwards.
3. Clean detergent dispenser and insert with water and a brush
and dry.
4. Attach insert and lock into position (push cylinder onto guide
pin).
5. Insert detergent drawer.
²
Leave detergent drawer open so that residual water can
evaporate.
Drain pump blocked
m Warning!
Danger of scalding!
Wash liquor is hot when washing at high temperatures.
You may be scalded if you touch the hot wash liquor.
Allow wash liquor to cool down.
²
Turn the tap off to prevent more water from flowing in and to
ensure that it is drained via the pump.
1. Switch off the device. Pull out the mains plug.
2. Open service flap.
3. Remove service flap.
32
4. Take the drainage hose out of the holder. Remove the
sealing cap, drain water into a suitable receptacle.
Press on sealing cap and insert drainage hose into the
holder.
Note: Residual water may run out.
5. Carefully unscrew the pump cover. Clean the interior, pump
cover thread and pump housing (fan impeller in the
detergent-solution pump must rotate).
6. Reinsert and screw on pump cover. Handle should be
vertical.
7. Insert service flap (1), engage (2) and close (3).
²
To prevent unused detergent from flowing into the outlet during
the next wash cycle: Pour approx. 1 litre of water into dispenser II
and start the Drain programme.
Drainage hose on the siphon blocked
1. Switch off the appliance. Pull out the mains plug!
Note: Residual water may run out!
2. Loosen hose clip, carefully remove drainage hose.
3. Clean drainage hose and siphon spigot.
4. Re-attach drainage hose and secure connection point with
hose clip.
33
Filter blocked in water inlet hose
First, release water pressure in the supply hose:
1. Turn off the tap!
2. Select any programme (except Spin/Drain).
3. Select Start/Reload Ü. Leave programme for approx. 40
seconds.
4. Press the # button. Appliance is switched off. Pull out the
mains plug!
5. Clean the filter:
Disconnect the hose from the water tap.
Clean filter with small brush.
and/or for standard and Aqua-Secure models:
Remove hose from the rear of the appliance.
Take out filter with pliers and clean.
6. Connect the hose and check for leaks.
34
Emergency release
The programme continues running when the power supply is
restored. If the washing is still to be removed, the door can be
opened as described below:
m Warning!
Danger of scalding!
Wash liquor and washing may be hot. If touched, there
is a risk of scalding.
If required, leave to cool down.
m Caution!
Danger when reaching into/gripping the rotating
drum!
If you reach into the rotating drum, you may injure your
hands.
Do not grip the rotating drum. Wait until the drum stops
rotating.
m Caution!
Water damage possible!
Leaking water may cause damage.
Do not open the door if you can still see water through
the glass.
1. Switch off the appliance. Pull out the mains plug!
2. Drain the water.
3. Pull down emergency release with a tool and release.
Door can then be opened.
35
Information on the display panel
Display
Cause/Remedy
CLOSE
DOOR
– Washing may be caught. Please open and close washing
machine door again and select Start/Reload Ü.
– If required, shut washing machine door or remove washing and
shut again.
– If required, switch appliance off and on again; set programme
and make individual settings; start programme.
LOW WATER
PRESSURE
OPEN TAP
– Turn on tap fully.
– Supply hose kinked/jammed.
– Water pressure too low. Clean the filter. ~ Page 34
PUMP IS
BLOCKED
CLEAN PUMP
– Drain pump blocked. Clean the drain pump. ~ Page 32
– The water drainage pipe/drain hose is blocked. Clean the
drainage hose on the siphon. ~ Page 33
DOOR IS
LOCKED
Water level or temperature is too high.
Select Start/Reload Ü to continue the programme.
LOCKING ...
UNLOCKING ...
If the Start/Reload Ü button is pressed too frequently
(e.g. repeatedly reloading items of washing), the door lock may
overheat. Wait for the door lock to lock or unlock.
´: ÌÍ
not applicable without AquaStop
Water in the base pan, appliance leaking.
Call customer service! ~ Page 39
ERROR ´: XXX
Switch off appliance, wait 5 seconds and switch on again. If the
display is indicated again, call customer service. ~ Page 39
36
Faults, what to do?
Faults
Cause/Remedy
Water is running out.
– Correctly attach/replace drainage hose.
– Tighten screw-fitting on the supply hose.
Water not flowing in.
Detergent not
washed in.
–
–
–
–
Washing-machine
door cannot be
opened.
– Safety function active. Stop programme? ~ Page 19
– Rinse Hold $ (without final spin) selected? ~ Page 20
– Can be opened via emergency release only? ~ Page 35
Programme does
not start.
– Start/Reload Ü or Finish in time selected?
– Door closed?
– Childlock active? Deactivate. ~ Page 18
Detergent solution is
not drained.
– Rinse Hold $ (without final spin) selected? ~ Page 20
– Clean the drain pump. ~ Page 32
– Clean outlet pipe and/or drainage hose.
Water not visible in
the drum.
Not a fault – water below the visible area.
Spin result not
satisfactory.
Washing wet/too
damp.
– Not a fault – unbalanced load detection system has stopped the
spin cycle, washing unevenly distributed.
Distribute small and large items of washing in the drum.
– Less Ironing { selected? ~ Page 17
– Too low speed selected? ~ Page 22
Spin cycle actuated
several times.
Not a fault – unbalanced load detection system adjusts imbalance.
Residual water in the
dispenser for care
product.
– Not a fault – effect of the care product not impaired.
– If required, clean insert. ~ Page 32
Odour formation in
the washing
machine.
Run Cotton 90 °C programme without washing.
Use standard detergent.
Loud noise
formation, vibrations
and “wandering”
during spin cycle.
– Appliance aligned?
Align the appliance. ~ Page 50
– Appliance feet fixed?
Secure appliance feet. ~ Page 50
– Transportation safety devices removed?
Remove transportation protection devices. ~ Page 45
Start/Reload Ü not selected?
Tap not open?
Filter blocked? Clean the filter. ~ Page 34
Supply hose kinked or jammed?
37
Faults
Cause/Remedy
Display panel/
indicator lights do
not function while
the appliance is
running.
– Power failure?
– Fuse tripped? Switch on/replace fuse.
– If the fault occurs repeatedly, call customer service. ~ Page 39
The programme
takes longer than
usual.
– Not a fault – unbalanced load detection system adjusts
imbalance by repeatedly distributing the washing.
– Not a fault – foam detection system active – several rinse cycles
are switched on.
Detergent residue
on the washing.
– Occasionally phosphate-free detergents contain water-insoluble
residue.
– Select Rinsing or brush the laundry after washing.
In the pause status
Start/Reload Ü
flashes very quickly
and a signal sounds.
– Water level too high. Washing cannot be reloaded. Immediately
close washing machine door.
– Select Start/Reload Ü to continue the programme.
If a fault cannot be rectified (switching the machine on and off) or a repair is required:
– Switch off the appliance and pull out the mains plug.
– Turn off the tap and call customer service. ~ Page 39
38
Customer service
If you cannot rectify the fault yourself, Faults, what to do?
~ Page 37, please contact our customer service. We will always
finds a suitable solution to avoid unnecessary visits by
technicians.
Please give customer service the product number (E-Nr.) and the
production number (FD) of the appliance.
(1U
Product number
)'
Production number
These instructions can
be found on: inside of
washing machine
door */open service
flap * and rear of the
appliance.
* depending on model
Rely on the competence of the manufacturer.
Contact us. You can therefore be sure that the repair is carried
out by trained service technicians who carry original spare parts.
39
Standard accessories
ngilIast
hte
apnicle
GHSHQGLQJRQPRGHO
$TXD6WRS
6WDQGDUG$TXD6HFXUH
0DLQVFDEOH
:DWHURXWOHW
:DWHULQOHW
,QVWUXFWLRQPDQXDODQG
,QVWDOODWLRQLQVWUXFWLRQV
&RYHUV
(OERZ
IRUVHFXULQJWKH
ZDWHURXWOHWKRVH
6SDQQHU
Also required for connection of the water drainage hose to a
siphon:
1 hose clip Ø 24–40 mm (DIY store) is also required for
connection to a siphon. Connecting the water ~ Page 49
Useful tools:
Ø Spirit level for alignment.
Ø Socket wrench
size 13: for loosening the transportation protection devices
~ Page 45 and
size 17: for aligning the appliance feet. ~ Page 50
40
Hose and cable lengths
GHSHQGLQJRQPRGHO
&RQQHFWLRQRQOHIWVLGH
aFP
aFP
aFPaFP
²
RU
&RQQHFWLRQRQULJKWVLGH
aFP
aFP
aFPaFP
PD[
FP
If the hose holders are used, the possible hose lengths are
reduced!
Available from dealer/customer service:
Ø Extension for Aqua-Stop or cold water inlet hose
(approx. 2.50 m).
Order no. WMZ2380, WZ10130, CZ11350, Z7070X0
Ø Longer supply hose (approx. 2.20 m), for standard model.
Technical specifications
Dimensions
60 x 59 x 85 cm
(width x depth x height)
Weight
depending on modell: 63–83 kg
Mains connection
Nominal voltage 220–240 V, 50 Hz
Nominal current 10 A
Nominal power 2300 W
Water pressure
100–1000 kPa (1–10 bar)
41
Installation
²
Humidity in the drum is caused by the final inspection.
Secure installation
m Warning!
Risk of injury!
– The washing machine is heavy – caution: take care
when lifting it.
– If the washing machine is raised by protruding
components (e.g. washing machine door), the
components may break off and cause injuries.
Donot lift the washing machine by its projecting
parts.
m Caution!
Risk of stumbling!
If the hoses and power cord are installed improperly,
there is a risk of tripping and injury.
Lay hoses and cables in such a way that there is no
risk of stumbling.
m Caution!
Washing machine may be damaged!
– Frozen hoses may tear/burst.
Do not install the washing machine in an area where
there is a risk of frost or outdoors.
– If the washing machine is raised by protruding
components (e.g. washing machine door), the
components may break off and the washing
machine may be damaged.
Donot lift the washing machine by its projecting
parts.
²
42
– In addition to the safety information listed here, the local
water and electricity supplier may have special requirements.
– If in doubt, have the appliance connected by a technician.
m Warning!
Risk of injury!
– The washing machine is heavy – caution: take care
when lifting it.
– If the washing machine is raised by protruding
components (e.g. washing machine door), the
components may break off and cause injuries.
Do not lift the washing machine by its projecting
parts.
m Caution!
Risk of stumbling!
If the hoses and power cord are installed incorrectly,
there is a risk of tripping and injury.
Lay hoses and cables in such a way that there is no
risk of stumbling.
m Caution!
Washing machine may be damaged!
– Frozen hoses may tear/burst.
Do not install the washing machine in an area where
there is a risk of frost or outdoors.
– If the washing machine is raised by protruding
components (e.g. washing machine door), the
components may break off and the washing
machine may be damaged.
Do not lift the washing machine by its projecting
parts.
²
– In addition to the safety information listed here, the local
water and electricity supplier may have special requirements.
– If in doubt, have the appliance connected by a technician.
Installation area
²
Stability is important to prevent the washing machine from
wandering!
– The installation area must be firm and level.
– Soft floors/floor coverings are not suitable.
Installation on a platform with drawer
Platform: order no. WMZ 20490, WZ- 20490
43
Installing the appliance on a base or on a wooden joist
ceiling
m Warning!
Washing machine may be damaged!!
The washing machine may wander during the spin
cycle and topple/fall off the base.
Always secure the washing machine feet with fixing
brackets.
Holding brackets: order no. WMZ 2200, WX 9756,
CZ 110600, Z 7080X0
²
If installing on a wooden joist ceiling:
– If possible, install the washing machine in a corner.
– Screw a water-resistant wooden panel (min. 30 mm thick) to
the floor.
Appliance installed under/between kitchen units
m Warning!
Danger of death from electric shock!
Danger of death if live parts are touched.
The appliance cover plate must not be removed.
²
44
– 60 cm cavity width required.
– Install washing machine only under a continuous worktop
connected firmly to the adjacent cupboards.
Remove transportation protection
devices
m Caution!
Washing machine may be damaged!
Transit bolts which have not been removed may
damage e.g. the drum while the washing machine is
running.
Before using the appliance for the first time, remove
the 4 transportation protection devices completely
and keep in a safe place.
m Caution!
Washing machine may be damaged!
To prevent damage in transit when transporting the
washing machine subsequently, always re-install the
transit bolts prior to transportation.
Keep screw and sleeve screwed together.
1. Take the hoses out of the holders.
2. Take hoses out of the elbow and remove elbow.
45
3. Loosen and remove all 4 transportation lock screws.
4. Take the power cord out of the holders. Remove sleeves.
5. Insert covers.
²
46
Lock covers firmly by pressing on the locking hook.
Connecting the water
m Warning!
Danger of death from electric shock!
Danger of death if live parts are touched.
Do not immerse Aqua-Stop safety device in water
(contains an electric valve).
²
– To prevent leakage or water damage, follow the instructions
in this chapter!
– Operate the washing machine with cold drinking water only.
– Do not connect to the mixer tap of an unpressurised hotwater apparatus.
– Use only the supplied inlet hose or one purchased from an
authorised specialist outlet, not a used one!
– If in doubt, have the appliance connected by a technician.
Water inlet hose
²
Water inlet hose: do not kink, crush, modify or sever (strength is
no longer guaranteed).
Optimum water pressure in the mains: 100–1000 kPa
(1–10 bar)
Ø When the tap is turned on, the water flow is at least 8 l/min.
Ø If the water pressure is higher, install a pressure reducing
valve.
1. Connect the water supply hose.
m Warning!
Threads for screw connections may be damaged!
If the screw connections are tightened too tightly using
a tool (pliers), the threads may be damaged.
Tighten plastic screw-fittings by hand only.
to the tap (¾" = 26.4 mm):
PD[
ƒ
PLQPP
PD[
ƒ
Aqua-Stop and Aqua-Secure Standard
47
on the appliance:
for Standard and Aqua-Secure models
2. Carefully turn on the tap and check that the connection points
are not leaking.
²
Screw connection is under water pipe pressure.
Water drainage hose
²
– Do not kink or protract the the water supply hose.
– Height difference between the placement area and drainage
point: 0 – maximum 100 cm
Drainage into a wash basin
m Warning!
Water damage possible!
If the attached drainage hose slips out of the
washbasin due to high water pressure when draining
the washing machine, leaking water may cause
damage.
Secure the drainage hose to prevent it from slipping
out of the sink.
m Caution!
The appliance may be damaged.
If the end of the drainage hose is immersed in the
drained water, water may be drawn back into the
appliance!
– The plug must not be in the plug hole.
– When the water is being pumped out of the
washing machine, check that the water drains
away quickly enough.
– The end of the drainage hose must not be
immersed in the drained water!
Installing the drainage hose:
48
Drainage into a siphon
m Warning!
Water damage possible!
If the drainage hose slips off the siphon connection
due to high water pressure when draining the washing
machine, leaking water may cause damage.
Connection point must be secured with hose clip,
Ø 24–40 mm (specialist outlet).
Connecting
Drainage into a plastic pipe with rubber sleeve or into a gully:
m Warning!
Water damage possible!
If the drainage hose slips off the plastic pipe due to
high water pressure when draining the washing
machine, leaking water may cause damage.
Secure the drainage hose to prevent it from slipping
out of the sink.
Connecting
49
Alignment
1. Loosen lock nut in a clockwise direction with a wrench.
2. Check alignment of the washing machine with a spirit level
and, if required, correct. Adjust the height by rotating the foot.
50
²
All four feet must be firmly on the floor.
The washing machine must not wobble!
3. Tighten the lock nut against the housing.
Grip the foot and do not adjust the height.
²
– The lock nuts on all four appliance feet must be screwed
tightly against the housing!
– Loud noise formation, intense vibrations and “wandering”
may be due to incorrect alignment!
Electrical connection
Electrical safety
m Warning!
Danger of death from electric shock!
Danger of death if live parts are touched.
– Never pull out the mains plug by tugging the power
cord.
– Insert/pull out the mains plug with dry hands only.
– Never pull out the mains plug during operation.
– Connect the washing machine to an alternating
current via a correctly installed earthed socket only.
– The mains voltage and voltage specifications on
the washing machine (appliance rating plate) must
match.
– Connected load as well as required fuse are
indicated on the appliance rating plate.
Ensure that:
– Mains plug and socket match fit.
– Cable cross-section is adequate.
– Earthing system has been installed correctly.
– A damaged power cord may be replaced by
an electrician only. A replacement mains cable can
be obtained from customer service.
– Do not use multiple plugs/couplings or extension
cables.
– If a residual-current-operated circuit breaker is
used, use only a type which features this symbol:
z.
Only this symbol guarantees compliance with
currently valid regulations.
– The mains plug must be accessible at all times.
51
Before the 1st washing
The washing machine was inspected thoroughly before leaving
the factory. To remove any water left over from testing
procedures, the first washing cycle should be carried out without
laundry in the machine.
²
The washing machine must have been installed and connected
properly. See chapter Installing ~ Page 50
1. Check the machine.
²
Never switch on a damaged machine. Inform your customer
service. ~ Page 39
2. Remove protective film from the fascia.
3. Insert mains plug.
4. Turn the tap on.
5. Switch on the appliance.
6. Close the washing machine door. Do not load any washing.
7. Select the Cotton programme.
8. Select the temperature 90 °C.
9. Open the detergent drawer.
10. Pour approx. 1 litre of water (1¾ pt) into dispenser II.
11. Add standard detergent to dispenser II according
to manufacturer’s instructions for light soiling.
²
To prevent frothing, use only half the recommended amount
of detergent. Do not use any standard or mild detergents.
12. Close the detergent drawer.
13. Select Start/Reload Ü.
14. When the programme ends, switch off the appliance.
Your washing machine is now ready for use.
52
Transportation, e.g. if moving house
Preparatory work
1. Turn off the tap.
2. Release the water pressure in the supply hose. Maintenance
– Filter in the water inlet hose ~ Page 34
3. Drain any residual detergent solution. Maintenance – Drain
pump blocked ~ Page 32
4. Isolate the washing machine from the power supply.
5. Remove the hoses.
Installing transportation protection devices
1. Remove covers and keep in a safe place.
If required, use a screwdriver.
2. Insert all 4 sleeves.
Clamp mains cable on the holders. Insert and tighten the
bolts.
Before switching on the appliance:
²
– Remove the transportation protection devices! ~ Page 45
– To prevent unused detergent from flowing into the outlet
during the next wash: Pour 1 litre of water into dispenser II
and start the Drain programme.
53
Index
A
Alignment, 50
B
Basic Settings 3 sec., 11, 29
Button
ecoPerfect ¦, 11, 16, 26
Extra Rinse, 11, 17, 27
Finish in, 11, 16, 26
Less Ironing, 11, 17, 26
Prewash, 11, 17, 27
C
Cancelling
the programme, 19
Care, 31
Drum, 31
Machine housing/Control
panel, 31
Changing
the programme, 19
Childlock, 18, 26
Cleaning
the detergent drawer, 32
the filter, 34
the siphon, 33
Connecting the water, 47
Water drainage, 48
Water supply, 47
Consumption values, 28
Control panel, 11
Customer service, 39
D
Descaling, 31
Detergent drawer, 10
Display panel, 11
Dosing recommendation, 30
Drain pump blocked, 32
Drum light, 13
Dyeing/Discolouring, 25
E
ecoPerfect ¦, 11, 16, 26
Electrical connection, 51
Emergency release, 35
End of the programme, 20
Extra Rinse, 11, 17, 27
F
Faults, what to do?, 37
Finish in, 11, 16, 26
G
Getting to know your
appliance, 9
H
Hints and tips, 7
Hose and cable lengths, 41
54
Aqua-Sensor, 30
Rinse Hold, 11, 17, 27
speedPerfect G, 11, 16,
26
Spin, 11, 16, 26
Start/Reload, 11
Temperature, 11, 16, 26
I
Information on the display
panel, 36
Inserting
the laundry, 13, 14, 15
Installation, 42
Installing transportation
protection devices, 53
Intended use, 4
L
Less Ironing, 11, 17, 26
Load adjust, 30
Load sensor/Load display, 30
M
Maintenance, 31
O
Old appliance, 7
P
Packaging, 7
Prewash, 11, 17, 27
Programme overview, 22
Programme selector, 11
Q
Quick-reference instructions, 8
R
Rinse Hold, 11, 17, 20, 27
S
Safety instructions, 5, 25
Selecting
the programme, 14
Settings 3 sec., 29
Soaking, 25
Sorting
the washing, 12
speedPerfect G, 11, 16, 26
Spin, 11, 26
Standard accessories, 40
Starching, 25
Starting
the programme, 17
T
Taste
Basic Settings 3 sec., 29
Technical specifications, 41
Temperature, 11, 16, 26
Topping up
laundry, 19
Transport bolts, 45
U
Unbalanced load detection
system, 30
Unloading
the laundry, 21
Programme sequence, 18
Programme
settings, 15, 22, 26
Protection of the
environment, 7
55
Aqua-Stop warranty
For appliances with Aqua-Stop only
In addition to warranty claims against the seller based on the contract of sale and in addition
to our appliance warranty we shall pay damages under the following conditions:
1. If water damage is caused by a fault in our water safety system, we shall make
reparation for the damage with respect to private users.
2. The liability warranty applies to the service life of the appliance.
3. A claim can only be made under the warranty if the appliance and Aqua-Stop have
been correctly installed and connected according to our instructions; this also includes
a correctly installed Aqua-Stop extension (original accessory).
4. Our guarantee does not apply to defective cables/hoses or to fittings up to the
connection on the tap.
5. Appliances which feature Aqua-Stop can be left unattended during operation and it is
not necessary to turn off the tap afterwards.
6. The tap should only be turned off if you are away for a prolonged period, e.g. several
weeks holiday.
To book an engineer visit and product advice
GB
0844 8928999
Calls from a BT landline will be charged at up to 3 pence per
minute.
IE
01450 2655
0.03 € per minute at peak. Off peak 0.0088 € per minute.
Please find the contact data of all countries in the enclosed customer service list.
Siemens-Electrogeräte GmbH
Carl-Wery-Straße 34, 81739 München
siemens-home.com
*9000965198*
9000965198
(9404)