Extractor hood
[en] Instructions for installation and use
Ú Table of contents
e[nuoIrs]acitlfde
INSTRUCTION MANUAL............................................................ 2
Important safety information................................................ 2
Environmental protection ..................................................... 4
Operating modes................................................................... 4
Operation ............................................................................... 5
Cleaning and maintenance................................................... 8
Trouble shooting ................................................................... 9
After-sales service .............................................................. 10
INSTALLATION INSTRUCTIONS............................................. 11
Important safety information.............................................. 11
General information ............................................................ 13
Installation ........................................................................... 14
INSTRUCTION MANUAL
Produktinfo
Additional information on products, accessories, replacement
parts and services can be found at www.bosch-home.com and
in the online shop www.bosch-eshop.com
: Important safety information
Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for
future use or for subsequent owners.
The appliance can only be used safely if it
is correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly
at its installation location.
This appliance is intended for domestic use
and the household environment only. The
appliance is not intended for use outside.
Do not leave the appliance unattended
during operation. The manufacturer is not
liable for damage which is caused by
improper use or incorrect operation.
This appliance may be used by children
over the age of 8 years old and by persons
with reduced physical, sensory or mental
capabilities or by persons with a lack of
experience or knowledge if they are
supervised or are instructed by a person
responsible for their safety how to use the
appliance safely and have understood the
associated hazards.
2
Children must not play with, on, or around
the appliance. Children must not clean the
appliance or carry out general maintenance
unless they are at least 8 years old and are
being supervised.
Keep children below the age of 8 years old
at a safe distance from the appliance and
power cable.
Check the appliance for damage after
unpacking it. Do not connect the appliance
if it has been damaged in transport.
This appliance is not intended for operation
with an external clock timer or a remote
control.
Danger of suffocation!
Packaging material is dangerous to
children. Never allow children to play with
packaging material.
Danger of death!
Risk of poisoning from flue gases that are
drawn back in.
Always ensure adequate fresh air in the
room if the appliance is being operated in
exhaust air mode at the same time as room
air-dependent heat-producing appliance is
being operated.
Room air-dependent heat-producing
appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters
or water heaters) obtain combustion air
from the room in which they are installed
and discharge the exhaust gases into the
open air through an exhaust gas system
(e.g. a chimney).
In combination with an activated vapour
extractor hood, room air is extracted from
the kitchen and neighbouring rooms - a
partial vacuum is produced if not enough
fresh air is supplied. Toxic gases from the
chimney or the extraction shaft are sucked
back into the living space.
■ Adequate incoming air must therefore
always be ensured.
■ An incoming/exhaust air wall box alone
will not ensure compliance with the limit.
Safe operation is possible only when the
partial vacuum in the place where the heatproducing appliance is installed does not
exceed 4 Pa (0.04 mbar). This can be
achieved when the air needed for
combustion is able to enter through
openings that cannot be sealed, for
example in doors, windows, incoming/
exhaust air wall boxes or by other technical
means.
In any case, consult your responsible
Master Chimney Sweep. He is able to
assess the house's entire ventilation setup
and will suggest the suitable ventilation
measures to you.
Unrestricted operation is possible if the
vapour extractor hood is operated
exclusively in the circulating-air mode.
Risk of fire!
■ Grease deposits in the grease filter may
catch fire.
Clean the grease filter at least every
2 months.
Never operate the appliance without the
grease filter.
■ Grease deposits in the grease filter may
catch fire. Never work with naked flames
close to the appliance (e.g. flambéing). Do
not install the appliance near a heatproducing appliance for solid fuel (e.g.
wood or coal) unless a closed, nonremovable cover is available. There must
be no flying sparks.
■ Hot oil and fat can ignite very quickly.
Never leave hot fat or oil unattended.
Never use water to put out burning oil or
fat. Switch off the hotplate. Extinguish
flames carefully using a lid, fire blanket or
something similar.
■ When gas burners are in operation without
any cookware placed on them, they can
build up a lot of heat. A ventilation
appliance installed above the cooker may
become damaged or catch fire. Only
operate the gas burners with cookware on
them.
■ Operating several gas burners at the
same time gives rise to a great deal of
heat. A ventilation appliance installed
above the cooker may become damaged
or catch fire. Never operate two gas
burners simultaneously on the highest
flame for longer than 15 minutes. One
large burner of more than 5 kW (wok) is
equivalent to the power of two gas
burners.
Risk of burns!
The accessible parts become very hot when
in operation. Never touch hot parts. Keep
children at a safe distance.
Risk of injury!
■ Components inside the appliance may
have sharp edges. Wear protective gloves.
■ Items placed on the appliance may fall
down. Do not place any objects on the
appliance.
■ The light emitted by LED lights is very
dazzling, and can damage the eyes (risk
group 1). Do not look directly into the
switched on LED lights for longer than
100 seconds.
Risk of fire!
Risk of fire!
Risk of fire!
Risk of fire!
Risk of injury!
Risk of injury!
3
Risk of electric shock!
■ A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in
the fuse box. Contact the after-sales
service.
■ Incorrect repairs are dangerous. Repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the
appliance from the mains or switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
■ Do not use any high-pressure cleaners or
steam cleaners, which can result in an
electric shock.
Risk of electric shock!
Causes of damage
Caution!
Risk of damage due to corrosion. Always switch on the
appliance while cooking to avoid condensation. Condensate
can produce corrosion damage.
Always replace faulty bulbs to prevent the remaining bulbs from
overloading.
Risk of damage due to ingress of humidity into the electronic
circuitry. Never clean operator controls with a wet cloth.
Surface damage due to incorrect cleaning. Clean stainless
steel surfaces in the direction of the grain only. Do not use any
stainless steel cleaners for operator controls.
Surface damage due to strong or abrasive cleaning agents.
Never use strong and abrasive cleaning agents.
Risk of damage from returning condensate. Install the exhaust
duct in such a way that it falls away from the appliance slightly
(1° slope).
Risk of electric shock!
Environmental protection
Environmentally-friendly disposal
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning used
electrical and electronic appliances (waste electrical
and electronic equipment - WEEE). The guideline
determines the framework for the return and recycling
of used appliances as applicable throughout the EU.
Dispose of packaging in an environmentally-friendly manner.
Operating modes
This appliance can be used in exhaust-air mode or circulatingair mode.
Circulating-air mode
The air which is drawn in is cleaned by the
grease filters and an activated carbon filter
and conveyed back into the kitchen.
Exhaust air mode
The air which is drawn in is cleaned by the
grease filters and conveyed to the exterior
by a pipe system.
Note: The exhaust air must not be conveyed into a functioning
smoke or exhaust gas flue or into a shaft which is used to
ventilate installation rooms which contain heat-producing
appliances.
■
■
4
Before conveying the exhaust air into a non-functioning
smoke or exhaust gas flue, obtain the consent of the heating
engineer responsible.
If the exhaust air is conveyed through the outer wall, a
telescopic wall box should be used.
Notes
■ To bind odours in circulating-air mode, you must install an
activated carbon filter. The different options for operating the
appliance in circulating-air mode can be found in the
brochure. Alternatively, ask your dealer. The required
accessories are available from specialist retailers, from
customer service or from the Online Shop.
■
For appliances with an additional internal filter, only the
CleanAir recirculation module (see Accessories for
circulating-air mode) can be used.
Operation
These instructions apply to several appliance variants. It is
possible that individual features are described which do not
apply to your appliance.
Note: Switch on the extractor hood when you start cooking and
switch it off again several minutes after you have finished
cooking. This is the most effective way of removing the kitchen
fumes.
Control panel model 1
Control panel
ERRVW
Saturation display
When the metal mesh grease filters or the activated carbon
filter are saturated, a signal sounds for approx. 4 seconds after
the fan is switched off.
In addition, the corresponding symbol appears in the display:
■
Metal mesh grease filter: #
■
Activated carbon filter: ’#
If you have not yet done so, the metal mesh grease filters
should be cleaned or the activated carbon filter changed now.
For instructions on how to clean the metal mesh grease filters,
please refer to the section Cleaning and maintenance.
While the saturation displays are flashing, they can be reset. To
do this, press the – button.
Explanation
Switching over the display for circulating-air mode
Fan on/off
For circulating-air mode, the electronic control display must be
switched over accordingly:
-
Reduce the fan settings/fan run-on time
■
+
Increase the fan settings/intensive setting 1, 2
■
%
B
Light on/off/dimming
Setting the fan
Switching on the appliance
■
■
Press the % button.
The fan starts at setting ƒ.
Press the + or - button to change the fan strength.
■
The extractor hood must be connected and switched off.
Press the % and - button at the same time until the
™# display for starter sets for circulating-air mode or
’# display for CleanAir circulating air modules
lights up.
Repeatedly press the button combination to switch the
electronic control display back to exhaust air mode (#
display).
Audible signal
Switching off
Switching on the acoustic signal
Press the % button.
When the fan is switched off, press the % and + buttons at the
same time for approx. three seconds. An acknowledgement
signal sounds.
Intensive setting
You can use the intensive setting if there is a large build-up of
odours and fumes/vapours.
Switching off the acoustic signal
Repeat the "Switching on the acoustic signal" process.
Press the + button when the fan is at setting „.
The intensive boost setting‚ is activated. Pressing the + button
again activates the intensive boost ƒsetting.
After approx. six minutes, the electronics automatically reduce
the fan to a lower setting . If you want to end the intensive
setting before the preset time expires, press the - button until
the required fan setting is reached.
Fan run-on time
Press the - button until ‚r appears.
After approx. ten minutes, the fan switches off automatically.
Lighting
The lighting can be switched on and off independently of the
fan.
Press the B button.
Setting the brightness
Press and hold the B button until the desired brightness is
reached.
5
Control panel model 2
Saturation display
Control panel
When the metal mesh grease filters or the activated carbon
filter are saturated, a signal sounds for approx. 4 seconds after
the fan is switched off.
ERRVW
Explanation
%
Fan on/off
#
Switch off the saturation display
-
Reduce the fan settings
+
Increase the fan settings/intensive setting 1, 2
r
B
Fan run-on time
Light on/off/dimming
Setting the fan
Switching on the appliance
■
■
Press the % button.
The fan starts at setting ƒ.
■
Metal mesh grease filter: #
■
Activated carbon filter: ’#
If you have not yet done so, the metal mesh grease filters
should be cleaned or the activated carbon filter changed now.
For instructions on how to clean the metal mesh grease filters,
please refer to the section Cleaning and maintenance.
While the saturation displays are flashing, they can be reset. To
do this, press the # button.
Switching over the display for circulating-air mode
For circulating-air mode, the electronic control display must be
switched over accordingly:
■
■
Press the + or - button to change the fan strength.
Switching off
Press the % button.
Intensive setting
You can use the intensive setting if there is a large build-up of
odours and fumes/vapours.
Press the + button when the fan is at setting „.
The intensive boost setting‚ is activated. Pressing the + button
again activates the intensive boost ƒsetting.
After approx. six minutes, the electronics automatically reduce
the fan to a lower setting . If you want to end the intensive
setting before the preset time expires, press the - button until
the required fan setting is reached.
Fan run-on time
The fan run-on time is possible at every fan setting (except
boost‚ and boost ƒ).
Select the desired fan setting and press the r button.
Šminr appears on the display.
Once this time has elapsed, the fan switches off automatically.
Setting the run-on time
When Šminr appears on the display, press the + or - button.
You can set a run-on time of between 1 and 9 minutes.
Lighting
The lighting can be switched on and off independently of the
fan.
Press the B button.
Setting the brightness
Press and hold the B button until the desired brightness is
reached.
6
In addition, the corresponding symbol appears in the display:
■
The extractor hood must be connected and switched off.
Press the % and r buttons at the same time until the
™# display for starter sets for circulating-air mode or
’# display for CleanAir circulating air modules
lights up.
Repeatedly press the button combination to switch the
electronic control display back to exhaust air mode (#
display).
Audible signal
Switching on the acoustic signal
When the fan is switched off, press the % and + buttons at the
same time for approx. three seconds. An acknowledgement
signal sounds.
Switching off the acoustic signal
Repeat the "Switching on the acoustic signal" process.
Control panel model 3
Control panel
1. When the fan is switched off, press the 1 button and hold it
ERRVW
HFR
If the sensor control responds too quickly or too slowly, it can
be changed accordingly:
HFR
for approx. 4 seconds. The setting is displayed.
2. Press the + or - button to change the setting of the sensor
control.
3. To confirm the entries, press and hold the 1 button for
approx. 4 seconds.
Explanation
%
Fan on/off
1
Eco function (automatic mode)
-
Reduce the fan settings
+
Increase the fan settings/intensive setting 1, 2
r
Fan run-on time
B
Light on/off/dimming
Fan run-on time
The fan run-on time is possible at every fan setting (except
boost‚ and boost ƒ).
Select the desired fan setting and press the r button.
Šminr appears on the display.
Once this time has elapsed, the fan switches off automatically.
Setting the run-on time
Setting the fan
When Šminr appears on the display, press the + or - button.
Switching on the appliance
You can set a run-on time of between 1 and 9 minutes.
■
■
Press the % button.
The fan starts at setting ƒ.
Press the + or - button to change the fan strength.
Lighting
The lighting can be switched on and off independently of the
fan.
Switching off
Press the B button.
Press the % button.
Setting the brightness
Intensive setting
Press and hold the B button until the desired brightness is
reached.
You can use the intensive setting if there is a large build-up of
odours and fumes/vapours.
Saturation display
Press the + button when the fan is at setting „.
The intensive boost setting‚ is activated. Pressing the + button
again activates the intensive boost ƒsetting.
After approx. six minutes, the electronics automatically reduce
the fan to a lower setting . If you want to end the intensive
setting before the preset time expires, press the - button until
the required fan setting is reached.
Automatic mode
Switching on the appliance
■
■
Press the % button.
The fan starts at ƒ setting.
Press the 1 button.
The optimum fan setting ‚, ƒ or „ is automatically set via a
sensor.
Switching off the appliance
Press the 1 or % button to switch off automatic mode.
The fan switches off automatically if the sensor no longer
detects a change in the air quality of the room.
When the metal mesh grease filters or the activated carbon
filter are saturated, a signal sounds for approx. 4 seconds after
the fan is switched off.
In addition, the corresponding symbol appears in the display:
■
Metal mesh grease filter: #
■
Activated carbon filter: ’#
If you have not yet done so, the metal mesh grease filters
should be cleaned or the activated carbon filter changed now.
For instructions on how to clean the metal mesh grease filters,
please refer to the section Cleaning and maintenance.
While the saturation displays are flashing, they can be reset. To
do this, press the – button.
Switching over the display for circulating-air mode
For circulating-air mode, the electronic control display must be
switched over accordingly:
■
■
The automatic mode lasts 4 hours at most.
Sensor control
In automatic mode, a sensor in the extractor hood detects the
intensity of the cooking and roasting fumes. Depending on the
setting of the sensor, the fan automatically switches to another
fan setting.
Default sensitivity setting: †
Lowest sensitivity setting: ‹
Highest sensitivity setting: Š
■
The extractor hood must be connected and switched off.
Press the % and r buttons at the same time until the
™# display for starter sets for circulating-air mode or
’# display for CleanAir circulating air modules
lights up.
Repeatedly press the button combination to switch the
electronic control display back to exhaust air mode (#
display).
Audible signal
Switching on the acoustic signal
When the fan is switched off, press the % and + buttons at the
same time for approx. three seconds. An acknowledgement
signal sounds.
Switching off the acoustic signal
Repeat the "Switching on the acoustic signal" process.
7
Cleaning and maintenance
: Risk of burns!
Cleaning the metal mesh grease filters
The appliance will become hot during operation, especially
near the bulbs. Allow the appliance to cool down before
cleaning.
These instructions apply to several appliance variants. It is
possible that individual features are described which do not
apply to your appliance.
: Risk of electric shock!
: Risk of fire!
Penetrating moisture may result in an electric shock. Clean the
appliance using a damp cloth only. Before cleaning, pull out the
mains plug or switch off the circuit breaker in the fuse box.
: Risk of electric shock!
Do not use any high-pressure cleaners or steam cleaners,
which can result in an electric shock.
Grease deposits in the grease filter may catch fire.
Clean the grease filter at least every 2 months.
Never operate the appliance without the grease filter.
Notes
Do not use any aggressive, acidic or alkaline cleaning
agents.
■
■
: Risk of injury!
Components inside the appliance may have sharp edges. Wear
protective gloves.
Cleaning agents
Observe the information in the table to ensure that the different
surfaces are not damaged by using the wrong type of cleaning
agent. Do not use
■
harsh or abrasive cleaning agents,
■
cleaning agents with a high concentration of alcohol,
■
hard scouring pads or sponges,
■
high-pressure cleaners or steam cleaners.
■
When cleaning the metal mesh grease filters, also clean the
holder for the metal mesh grease filters in the appliance
using a damp cloth.
The metal mesh grease filters can be cleaned in the
dishwasher or by hand.
In the dishwasher:
Note: If the metal mesh grease filters are cleaned in the
dishwasher, slight discolouration may occur. This has no effect
on the function of the metal mesh grease filters.
■
■
Do not clean heavily soiled metal mesh grease filters together
with utensils.
Place the metal mesh grease filters loosely in the dishwasher.
The metal mesh grease filters must not be wedged in.
Wash new sponge cloths thoroughly before use.
By hand:
Follow all instructions and warnings included with the cleaning
agents.
Note: You can use a special grease solvent for stubborn dirt. It
can be ordered via the Online Shop.
Area
Cleaning agents
■
Soak the metal mesh grease filters in a hot soapy solution.
Stainless steel
Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth.
■
Clean the filters with a brush and then rinse them thoroughly.
■
Leave the metal mesh grease filters to drain.
Clean stainless steel surfaces in the
direction of the grain only.
Special stainless steel cleaning products are available from our after-sales
service or from specialist retailers.
Apply a very thin layer of the cleaning
product with a soft cloth.
Painted surfaces
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth/towel.
Do not use any stainless steel cleaners.
Aluminium and plas- Glass cleaner:
tic
Clean with a soft cloth.
Glass
Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Operating controls
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth.
Risk of damage to the electronics from
penetrating moisture. Never clean operator controls with a wet cloth.
Do not use any stainless steel cleaners.
8
Removing metal grease filter
1. Open the lock and fold down the metal grease filter. While
doing this, place the other hand under the metal grease filter.
For additional filters, open the lock and fold down the metal
grease filter. While doing this, place the other hand under the
metal grease filter.
2. Take the metal grease filter out of the holder.
Notes
For edge extraction filters, pull the metal grease filter
downwards. While doing this, place the other hand under the
metal grease filter.
■
■
Grease can accumulate in the bottom of the metal grease
filter.
Hold the metal grease filter level, otherwise grease will drip
out.
3. Clean the metal grease filter.
Installing the metal mesh grease filter
1. Insert the metal mesh grease filter.
While doing this, place the other hand under the metal mesh
grease filter.
2. Fold the metal mesh grease filter upwards, locking it in place.
Trouble shooting
Malfunctions often have simple explanations. Please read the
following notes before calling the after-sales service.
: Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be carried
out and damaged power cables replaced by one of our trained
after-sales technicians. If the appliance is defective, unplug the
appliance from the mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
Malfunction table
Problem
Possible cause Solution
The appliance
does not work
The plug is not
plugged in.
Connect the appliance to
the electricity supply
Power cut
Check whether other
kitchen appliances are
working
The lighting
does not work.
Faulty fuse
Check in the fuse box to
make sure that the fuse for
the appliance is OK
The bulbs are
faulty.
For information on changing the bulbs, see the
"Replacing Bulbs" section.
Replacing bulbs
These instructions apply to several appliance variants. It is
possible that individual features are described which do not
apply to your appliance.
: Risk of electric shock!
When changing the bulbs, the bulb socket contacts are live.
Before changing the bulb, unplug the appliance from the mains
or switch off the circuit breaker in the fuse box.
Important Only use a bulb of the same type and same power
(see the bulb holder or rating plate inside the appliance) – to
do this, remove the metal mesh grease filter.
Replacing halogen bulbs
Note: When inserting halogen bulbs, do not touch the glass
tube. Use a clean cloth to insert the halogen bulbs.
1. Carefully remove the bulb ring using a suitable tool.
2. Pull out the bulb and replace it with a bulb of the same type.
--------
3. Insert the bulb cover.
4. Insert the mains plug or switch on the fuse again.
LED lights
Defective LED lights may be replaced by the manufacturer, their
customer service or a qualified technician (electrician) only.
: Risk of injury!
The light emitted by LED lights is very dazzling, and can
damage the eyes (risk group 1). Do not look directly into the
switched on LED lights for longer than 100 seconds.
9
After-sales service
Our after-sales service is there for you if your appliance needs
to be repaired. We will always find the right solution in order to
avoid unnecessary visits from a service technician.
Basic equipment: Starter set for circulating-air mode - wide
3
When calling us, please give the product number (E no.) and
the production number (FD no.) so that we can provide you with
the correct advice. The rating plate with these numbers can be
found inside the appliance (remove the metal mesh grease
filter to gain access).
You can make a note of the numbers of your appliance and the
telephone number of the after-sales service in the space below
to save time should it be required.
E no.
FD no.
Throw-away filter
4
After-sales serviceO
Please be aware that a visit by an after-sales engineer will be
charged if a problem turns out to be the result of operator error,
even during the warranty period.
Basic equipment: CleanAir recirculation module - narrow
Please find the contact data of all countries in the enclosed
customer service list.
5
[
To book an engineer visit and product advice
GB
0344 892 8979
Calls charged at local or mobile rate.
IE
01450 2655
0.03 € per minute at peak. Off peak 0.0088 € per
minute.
Rely on the professionalism of the manufacturer. You can
therefore be sure that the repair is carried out by trained service
technicians who carry original spare parts for your appliances.
Accessories for circulating-air mode
[
Throw-away filter
6
(not included in the delivery)
Notes
■ Follow the installation instructions supplied with the
accessories.
■
For appliances with an additional internal filter, only the
CleanAir recirculation module can be used.
Basic equipment: CleanAir recirculation module - wide
7
[
Basic equipment: Starter set for circulating-air mode - narrow
1
Throw-away filter
8
Throw-away filter
2
10
1
DHZ 5365 channel width 260 mm
2
DHZ 5326 channel width 260 mm
3
DHZ 5385 channel width 345 mm
4
DHZ 5346 channel width 345 mm
5
DSZ 6220 channel width 260 mm
6
DSZ 5201 channel width 260 mm
7
DSZ 6230 channel width 345 mm
8
DSZ 5201 channel width 345 mm
[
INSTALLATION INSTRUCTIONS
Installation instructions
HOHFWUR
JD]
! PP
! PP
[
[
[
[
[
[
[
[
[
■
■
■
[
This appliance is fitted to the kitchen ceiling or a sturdy
suspended ceiling.
Follow the enclosed installation instructions for additional
special accessories (e.g. for circulating-air mode).
The surfaces of the appliance are sensitive. Avoid damaging
them during installation.
: Important safety information
Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for
future use or for subsequent owners.
The appliance can only be used safely if it
is correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly
at its installation location.
The width of the extractor hood must
correspond at least with the width of the
hob.
For the installation, observe the currently
valid building regulations and the
regulations of the local electricity and gas
suppliers.
When conveying the exhaust air, official and
legal regulations (e.g. state building
regulations) must be followed.
Risk of death!
Risk of poisoning from flue gases that are
drawn back in. The exhaust air must not be
conveyed into a functioning smoke or
exhaust gas flue or into a shaft which is
used to ventilate installation rooms that
contain heating appliances. If the exhaust
air is to be conveyed into a non-functioning
smoke or exhaust gas flue, you must obtain
the consent of the heating engineer
responsible.
Danger of death!
Risk of poisoning from flue gases that are
drawn back in.
Always ensure adequate fresh air in the
room if the appliance is being operated in
exhaust air mode at the same time as room
air-dependent heat-producing appliance is
being operated.
11
Room air-dependent heat-producing
appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters
or water heaters) obtain combustion air
from the room in which they are installed
and discharge the exhaust gases into the
open air through an exhaust gas system
(e.g. a chimney).
In combination with an activated vapour
extractor hood, room air is extracted from
the kitchen and neighbouring rooms - a
partial vacuum is produced if not enough
fresh air is supplied. Toxic gases from the
chimney or the extraction shaft are sucked
back into the living space.
■ Adequate incoming air must therefore
always be ensured.
■ An incoming/exhaust air wall box alone
will not ensure compliance with the limit.
Safe operation is possible only when the
partial vacuum in the place where the heatproducing appliance is installed does not
exceed 4 Pa (0.04 mbar). This can be
achieved when the air needed for
combustion is able to enter through
openings that cannot be sealed, for
example in doors, windows, incoming/
exhaust air wall boxes or by other technical
means.
In any case, consult your responsible
Master Chimney Sweep. He is able to
assess the house's entire ventilation setup
and will suggest the suitable ventilation
measures to you.
Unrestricted operation is possible if the
vapour extractor hood is operated
exclusively in the circulating-air mode.
12
Danger of death!
Risk of poisoning from flue gases that are
drawn back in. If installing a ventilation
system in a room with a heat-producing
appliance connected to a chimney/flue, the
electricity supply to the hood must be
equipped with a suitable safety switch.
Risk of fire!
Grease deposits in the grease filter may
catch fire. The specified safety distances
must be observed in order to prevent an
accumulation of heat. Observe the
specifications for your cooking appliance. If
gas and electric hobs are operated
together, the largest specified distance
applies.
Only one side of the appliance may be
installed directly next to a high-sided unit or
a wall. The distance between the appliance
and wall or high-sided unit must be at least
50 mm.
Risk of injury!
■ Components inside the appliance may
have sharp edges. Wear protective gloves.
■ The appliance may fall down if it has not
been properly fastened in place. All
fastening components must be fixed firmly
and securely.
■ The appliance is heavy. To move the
appliance, 2 people are required. Use only
suitable tools and equipment.
Risk of electric shock!
Components inside the appliance may have
sharp edges. These may damage the
connecting cable. Do not kink or pinch the
connecting cable during installation.
Risk of electric shock!
It must always be possible to disconnect
the appliance from the electricity supply.
The appliance must only be connected to a
protective contact socket which has been
correctly installed. If the plug is no longer
accessible following installation of the
appliance, or a fixed connection is required,
an all-pole isolating switch must be present
on the installation side with a contact gap of
at least 3 mm. The fixed connection must
only be installed by an electrician.
Danger of suffocation!
Packaging material is dangerous to
children. Never allow children to play with
packaging material.
Risk of injury!
Risk of injury!
General information
Exhaust air mode
Electrical connection
: Risk of death!
: Risk of electric shock!
Risk of poisoning from flue gases that are drawn back in. The
exhaust air must not be conveyed into a functioning smoke or
exhaust gas flue or into a shaft which is used to ventilate
installation rooms that contain heating appliances. If the
exhaust air is to be conveyed into a non-functioning smoke or
exhaust gas flue, you must obtain the consent of the heating
engineer responsible.
Components inside the appliance may have sharp edges.
These may damage the connecting cable. Do not kink or pinch
the connecting cable during installation.
The required connection data can be found on the rating plate
inside the appliance; to do this, remove the metal mesh grease
filter.
Length of the cable: approx. 1.30 m
If the exhaust air is conveyed through the outer wall, a
telescopic wall box should be used.
This appliance complies with the EC interference suppression
regulations.
Exhaust duct
: Risk of electric shock!
Note: The device manufacturer does not assume any warranty
for complaints attributable to the pipe section.
It must always be possible to disconnect the appliance from the
electricity supply. The appliance must only be connected to a
protective contact socket which has been correctly installed. If
the plug is no longer accessible following installation of the
appliance, or a fixed connection is required, an all-pole isolating
switch must be present on the installation side with a contact
gap of at least 3 mm. The fixed connection must only be
installed by an electrician.
■
■
■
The device achieves its optimum performance by means of a
short, straight exhaust air pipe and as large a pipe diameter
as possible.
As a result of long rough exhaust air pipes, many pipe bends
or pipe diameters that are smaller than 150 mm, the optimum
extraction performance is not achieved and fan noise is
increased.
The pipes or hoses for laying the exhaust air line must
consist of non-combustible material.
Round pipes
An inner diameter of 150 mm, but at least 120 mm, is
recommended.
Flat ducts
The inner cross-section must correspond to the diameter of the
round pipes.
dia. 150 mm ca. 177 cm2
dia. 120 mm ca. 113 cm2
■
Flat ducts should not have any sharp deflections.
■
Use sealing strips for deviating pipe diameters.
Preparing the ceiling
■
■
■
■
The ceiling must be flat, horizontal and have adequate loadbearing capacity.
The depth of the bore holes must be the same length as the
screws. The wall plugs must have a secure grip.
The enclosed screws and wall plugs are suitable for solid
brickwork. Suitable fasteners must be used for other
structures (e.g. plasterboard, porous concrete, poroton
bricks).
The max. weight of the extractor hood is 50 kg.
13
Installation
Fitting the upper support frame
Fitting the lower support frame
1. Before fitting, determine the total height of the support frame
Fasten the upper and lower part of the support frame at the
specified total height using 10 screws.
and mark the screw holes.
Note: The height of the support frame can be adjusted in 20
mm intervals.
2. On the ceiling, mark the centre point of the appliance.
3. Using the enclosed template, mark the positions for the
screws on the ceiling.
Notes
■ Ensure that the lower support frame is in the correct position.
The open side must be facing the hob control elements.
■
The support frame can be subsequently re-positioned by
loosening the securing screws.
[
([KDXVWDLU
PP
[
&LUFXODWHGDLU
PP
[
4. Drill four 8 mm diameter holes to a depth of 80 mm for the
fasteners and press in the wall plugs flush with the ceiling.
5. Fasten the upper part of the support frame to the ceiling with
4 screws.
Note: Ensure that the support frame is in the correct position.
The middle bracket defines the preferred side and must be
facing the hob control elements.
14
[
Fitting the appliance
Attaching the flue duct
1. Hook the appliance from below into the support frame.
: Risk of injury!
Note: Ensure that the mains cable is not trapped.
2. Fasten the appliance to the support frame using 2 securing
screws.
From sharp edges during installation. Always wear protective
gloves while installing the appliance.
1. Separate the flue ducts.
To do this, remove the adhesive tape.
2. Remove the protective foil from both sides.
3. Place both parts of the upper flue on the appliance and push
together.
Note: The slots of the upper flue must point downwards.
[
4. Push up the upper flue part and secure with 2 screws.
3. Hook in the retaining clip and screw tight.
[
5. Insert both lower parts of the flue and push together.
Connecting the pipes
Note: If using an aluminium pipe, smooth the connection area
beforehand.
Exhaust-air pipe Ø 150 mm (recommended size)
Attach the exhaust-air pipe directly to the air-pipe connector
and seal.
Exhaust-air pipe Ø 120 mm
1. Attach the reducing connector directly to the air-pipe
connector.
2. Attach the exhaust air pipe to the reducing connector.
3. Seal both joints appropriately.
15
Robert Bosch Hausgeräte GmbH
Carl-Wery-Straße 34
81739 München
Germany
www.bosch-home.com
*9000904224*
9000904224
950114