Always there to help you
Register your product and get support at
www.philips.com/support
SD700
Question?
Contact
Philips
User manual
Contents
1Important
Hearing safety
2
2
2 Your Portable Speaker
4
Introduction4
What's in the box
4
Overview of the product
5
3 Get started
Power supply
Turn on or off
Select a source
6
6
6
7
4Play
8
Play from Bluetooth-enabled devices
8
Play from a Micro SD card or USB device 9
Play from an external device
9
Listen to FM radio
10
Listen through a headphone
10
Adjust volume
10
5 Product information
11
11
11
6Troubleshooting
13
13
Specifications
USB playability information
About Bluetooth device
7Notice
14
Compliance14
Care of the environment
14
Trademark notice
15
EN
1
1Important
Hearing safety
Warning
•• Never remove the casing of this product.
•• Never lubricate any part of this product.
•• Never place this product on other electrical equipment.
•• Keep this product away from direct sunlight, naked
flames or heat.
•
•
•
•
•
•
•
•
•
•
2
Read these instructions.
Follow all instructions.
Do not use this apparatus near water.
Do not block any ventilation openings.
Install in accordance with the
manufacturer's instructions.
Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that
produce heat.
Only use attachments/accessories specified
by the manufacturer.
Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
The battery shall not be exposed to
excessive heat such as sunshine, fire or the
like.
Apparatus shall not be exposed to
dripping or splashing.
Do not place any sources of danger on the
apparatus (e.g. liquid filled objects, lighted
candles).
EN
Listen at a moderate volume.
• Using headphones at a high volume can
impair your hearing. This product can
produce sounds in decibel ranges that may
cause hearing loss for a normal person,
even for exposure less than a minute. The
higher decibel ranges are offered for those
that may have already experienced some
hearing loss.
• Sound can be deceiving. Over time your
hearing 'comfort level' adapts to higher
volumes of sound. So after prolonged
listening, what sounds 'normal' can actually
be loud and harmful to your hearing. To
guard against this, set your volume to a safe
level before your hearing adapts and leave
it there.
To establish a safe volume level:
• Set your volume control at a low setting.
• Slowly increase the sound until you can
hear it comfortably and clearly, without
distortion.
Listen for reasonable periods of time:
• Prolonged exposure to sound, even
at normally 'safe' levels, can also cause
hearing loss.
• Be sure to use your equipment reasonably
and take appropriate breaks.
Be sure to observe the following guidelines
when using your headphones.
• Listen at reasonable volumes for
reasonable periods of time.
• Be careful not to adjust the volume as your
hearing adapts.
• Do not turn up the volume so high that
you can't hear what's around you.
• You should use caution or temporarily
discontinue use in potentially hazardous
situations.
Note
•• The type plate is located on the bottom of the
apparatus.
EN
3
2 Your Portable
Speaker
Congratulations on your purchase, and
welcome to Philips! To fully benefit from the
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this speaker, you can:
• listen to FM radio; and
• enjoy audio from Micro SD card, USB
devices, Bluetooth-enabled devices, and
other external devices.
What's in the box
Check and identify the contents of your
package:
• Speaker
• USB cable for charging
• FM antenna
• Short user manual
• Safety & notice leaflet
4
EN
Overview of the product
abcb
d
efg
h
m
i
l
j
k
a SRC
• Select an audio source.
b
c
/
• Select a track.
• Search within play.
• Tune to FM radio stations.
•
•
•
•
/PAIRING
In SD, USB, or Bluetooth mode, press
to pause or resume play.
In Bluetooth mode, press and hold for
three seconds to disconnect Bluetooth
connection or enter pairing mode.
In FM mode, press and hold for two
seconds to store FM radio stations
automatically.
In FM mode, press to select a preset
radio station.
j AUDIO IN/
• Connect an external audio device.
• Connect FM antenna.
k Display panel
• Show current status.
l
• Connect a USB storage device.
m SD slot
• Connect a Micro SD card.
d -/+
• Adjust volume.
e
• Turn the product on or off.
f Bluetooth indicator
g Hole for attaching the string
h DC 5V
• Recharge the built-in battery.
i
• Connect a headphone.
EN
5
3 Get started
Battery status
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of this apparatus. The
model number and serial number are on the
bottom of the apparatus. Write the numbers
here:
Model No. __________________________
Serial No. ___________________________
Low battery
While charging
Fully charged or charging
stopped
Battery icon (
behavior
Flashing
Solid on
Off
)
Turn on or off
•
To turn the product on, slide the switch
to the right.
»» The product switches to the last
selected source.
•
To turn the product off, slide the switch to
the left.
Power supply
The speaker can operate on the built-in
rechargeable battery.
Note
•• Before use, fully charge the built-in battery.
•• Rechargeable battery has a limited number of charge
cycles. Battery life and number of charge cycles vary by
use and settings.
To recharge the built-in battery:
Connect the supplied USB cable to:
• the DC 5V socket on the speaker.
• the USB socket on a computer.
Switch to ECO standby mode
DC 5V
6
EN
In SD, USB, Audio-in, or Bluetooth mode,
the product switches to ECO standby mode
automatically in the following situations:
• Music playback is stopped for 15 minutes;
• There is no Micro SD card, USB device or
Audio-in cable connected for 15 minutes;
or
• Bluetooth connection is disconnected for
15 minutes.
To return to the SD/USB/Audio-in/Bluetooth
mode:
• Press
to resume playback; or
• Slide the switch to turn the product off
first, then turn it on.
Select a source
Press SRC repeatedly to select an audio source:
FM tuner, USB, SD, Bluetooth, or Audio-in.
EN
7
4Play
Play from Bluetooth-enabled
devices
With this product, you can listen to audio from
Bluetooth-enabled devices.
Connect a device
Note
•• Make sure that your Bluetooth device is compatible
with this product.
•• Before pairing a device with this product, read its user
manual for Bluetooth compatibility.
•• The product can memorize a maximum of 4 paired
devices. The fifth connected device will replace the
first one.
•• Make sure that Bluetooth function is enabled on your
device, and your device is set as visible to all other
Bluetooth devices.
•• Any obstacle between this product and a Bluetooth
device can reduce the operational range.
•• Keep away from any other electronic device that may
cause interference.
•• The operational range between this product and a
Bluetooth device is approximately 10 meters (30 feet).
1
2
3
8
Press SRC repeatedly to select Bluetooth
source.
»» [bt] is displayed, and the Bluetooth
indicator flashes blue slowly.
Press and hold PAIRING until you hear
beep sound.
»» The product is ready for pairing.
»» The Bluetooth indicator flashes blue
quickly.
On your Bluetooth device, enable
Bluetooth and search for Bluetooth
devices.
EN
4
Select [Philips SD700] on your device to
start pairing and connection. If necessary,
enter default password “0000”.
»» After successful connection, the
speaker beeps twice, and the
Bluetooth indicator stop flashing.
Bluetooth indicator Status
Flashing blue quickly Ready for pairing a new
device
Flashing blue slowly Trying to connect a
paired device
Solid blue
Connected
To disconnect the Bluetooth-enabled device:
• Press and hold PAIRING for three seconds;
• Disable Bluetooth on your device; or
• Move the device beyond the
communication range.
»» The product beeps twice, and the
Bluetooth indicator flashes blue.
To reconnect the Bluetooth-enabled device:
• Next time when this product enters
Bluetooth mode, it will reconnect the last
connected device automatically; or
• On your Bluetooth device, select "Philips
SD700" on your Bluetooth menu to start
connection.
To connect another Bluetooth-enabled device:
1
2
Press and hold PAIRING for three seconds
to disconnect the currently connected
device.
»» The product enters Bluetooth pairing
mode.
Connect another Bluetooth device.
Play from Bluetooth device
After successful Bluetooth connection, play
audio on the Bluetooth device.
»» Audio streams from your Bluetooth
device to the product.
• To pause or resume play, press PAIRING.
Play from a Micro SD card or
USB device
Button
/
Note
•• Make sure that the USB storage device or Micro SD
card contains playable audio content.
Shuffle play
Play from a Micro SD card
1
2
Function
Press to skip to the previous or next
track.
Press and hold to fast forward or fast
reverse the track during playback,
then release to resume play.
Press to start, pause, or stop play.
Press SRC repeatedly to select the SD
card source.
»» [SD] is displayed.
Insert a Micro SD card into the card slot.
»» Play starts automatically.
During play, press and hold
and
simultaneously for 2 seconds.
»» [
] is displayed.
»» All tracks are played randomly.
Play from an external device
With this product, you can listen to an external
audio device such as an MP3 player.
1
2
Play from a USB storage device
1
2
Press SRC repeatedly to select the USB
source.
»» [USB] is displayed.
Insert the USB device into the
»» Play starts automatically.
socket.
3
Press SRC repeatedly to select AUX
source.
Connect an audio input cable with a 3.5
mm connector on both ends to
• the AUDIO IN socket on the speaker.
• the headphone socket on an external
device.
Play audio on the device (refer to its user
manual).
Control play
In USB or SD mode, follow the instructions
below to control play.
EN
9
Listen to FM radio
Tip
•• You can press
/
to stop auto scan.
Tune to FM radio stations
Note
•• Keep the product away from other electronic devices
to avoid radio interference.
1
Plug the FM antenna into the AUDIO IN/
socket.
Select a preset radio station
In tuner mode, press
preset station.
repeatedly to select a
Listen through a headphone
Plug a headphone into the
product.
socket on the
Adjust volume
During play, press -/+ to increase or decrease
volume.
2
3
4
Press SRC repeatedly to select FM tuner
source.
Press and hold
/
for two seconds.
»» The product tunes to a station with
strong reception automatically.
Repeat step 3 to tune to more radio
stations.
To tune to a station manually:
• Press
/
repeatedly until you find
better reception.
Store FM radio stations automatically
Note
•• You can store a maximum of 20 preset radio stations.
In FM tuner mode, press and hold
for two
seconds.
»» All available radio stations are stored
automatically, then the first stored
radio station is broadcast.
10
EN
Tip
•• You can press and hold -/+ for 2 seconds to increase or
decrease volume continuously.
5Product
information
Speaker
Speaker Impedance
Speaker Driver
Sensitivity
4 ohm
4cm full range
>79±3dB/m/W
Note
•• Product information is subject to change without prior
notice.
Specifications
Amplifier
Rated Output Power
Frequency Response
Signal to Noise Ratio
Aux Input
2 X 1.5W RMS
60 -20000 Hz, ±3 dB
>70 dBA
600mV RMS 22kohm
Tuner (FM)
Tuning Range
Tuning Grid
- Mono, 26dB S/N Ratio
- Stereo, 46dB S/N Ratio
Search Selectivity
Total Harmonic Distortion
Signal to Noise Ratio
FM: 87.5-108
MHz
50 KHz
<22 dBf
>43 dBf
>28 dBf
<2%
>55dB
Bluetooth
Bluetooth Version
Bluetooth Frequency
Band
Bluetooth Distance
V3.0+EDR
2.402GHz ~
2.48GHz ISM Band
10 m (Free space)
General information
Power Supply (through
Micro USB socket)
Built-in Battery (Lipolymer battery)
Eco Standby Power
Consumption
Dimensions - Main Unit
(W x H x D)
Weight - Main Unit
5V
500 mA
3.7 V, 850 mAh
<0.5 W
164 x 63 x 33 mm
0.35 kg
USB playability information
Compatible USB devices:
• USB flash memory (USB2.0)
• USB flash players (USB2.0)
• memory cards (requires an additional
card reader to work with this unit;
Some multi-card USB reader may not
be supported.)
Supported formats:
• USB or memory file format: FAT12,
FAT16, FAT32 (sector size: 512 bytes)
• MP3 bit rate (data rate): 32-320 Kbps
and variable bit rate
• Directory nesting up to a maximum of
8 levels
• Number of albums/ folders: maximum
99
• Number of tracks/titles: maximum 999
• File name in Unicode UTF8 (maximum
length: 16 bytes)
EN
11
Unsupported formats:
• Empty albums: an empty album is an
album that does not contain MP3/
WMA files, and is not be shown in the
display.
• Unsupported file formats are skipped.
For example, Word documents (.doc)
or MP3 files with extension .dlf are
ignored and not played.
• AAC, WAV, PCM audio files
• DRM protected WMA files (.wav, .m4a,
.m4p, .mp4, .aac)
• WMA files in Lossless format
12
EN
6Troubleshooting
Warning
•• Never remove the casing of this device.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
device, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips Web page (www.
philips.com/support). When you contact Philips,
make sure that the device is nearby and the
model number and serial number are available.
No power
• Recharge the battery.
No sound or poor sound
•• Adjust volume on this product.
•• Adjust volume on the connected device.
•• Check if you have selected the correct
audio source.
No response from the product
•• Turn on the product.
•• Recharge the battery.
•• Turn the product off first, then turn it
on to activate the product from standby
mode.
About Bluetooth device
The audio quality is poor after connection
with a Bluetooth-enabled device.
•• The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between them.
Fail to search out SD700 on your device for
pairing.
•• Press and hold PAIRING for three seconds,
and then try again.
Cannot connect with the device.
•• The Bluetooth function of the device is not
enabled. Refer to the user manual of the
device for how to enable the function.
•• This product is already connected with
another Bluetooth-enabled device.
Disconnect that device and then try again.
The paired device connects and disconnects
constantly.
•• The Bluetooth reception is poor. Move the
device closer to this product or remove
any obstacle between them.
•• For some devices, Bluetooth connection
may be deactivated automatically as a
power-saving feature. This does not indicate
any malfunction of this product.
Poor radio reception
•• Increase the distance between the product
and other electrical appliances.
•• Plug the FM antenna into the AUDIO IN/
socket for better reception.
•• Fully extend and adjust the position of the
antenna.
USB device not supported
•• The USB device is incompatible with the
unit. Try another one.
EN
13
7Notice
Any changes or modifications made to this
device that are not expressly approved by
Gibson Innovations may void the user’s
authority to operate the equipment.
Compliance
2522
Hereby, Gibson Innovations declares that this
product is in compliance with the essential
requirements and other relevant provisions
of Directive 1999/5/EC. You can find the
Declaration of Conformity on www.philips.com/
support.
European Directive 2013/56/EU which cannot
be disposed of with normal household waste.
We strongly advise you to take your product to
an official collection point or a Philips service
centre to have a professional remove the
rechargeable battery.
Inform yourself about the local separate
collection system for electrical and electronic
products and rechargeable batteries. Follow
local rules and never dispose of the product
and rechargeable batteries with normal
household waste. Correct disposal of old
products and rechargeable batteries helps
prevent negative consequences for the
environment and human health.
Caution
•• Removal of the built-in battery invalidates the warranty
and may destroy the product.
Always bring your product to a professional to
remove the built-in battery.
Care of the environment
Disposal of your old product and battery
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This symbol means that the product contains
a built-in rechargeable battery covered by
14
EN
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
Trademark notice
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Gibson
is under license. Other trademarks and trade
names are those of their respective owners.
EN
15
Specifications are subject to change without notice.
2015 © Gibson Innovations Limited. All rights reserved.
This product has been manufactured by, and is sold under the responsibility of Gibson
Innovations Ltd., and Gibson Innovations Ltd. is the warrantor in relation to this product.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V.
and are used under license from Koninklijke Philips N.V.
SD700_00_UM_V2.0