Samsung WD90J6410AW washer dryer

Washing Machine
User manual
WD90J6***** / WD80J6*****
SSEC SEC
WD80J6410AX-EN.indd 1
2015/2/7 11:39:00
Contents
Contents
Safety information
3
What you need to know about the safety instructions
Important safety symbols
Important safety precautions
Instructions about the WEEE
3
3
4
14
Installation
15
What’s included
Installation requirements
Step-by-step installation
15
17
19
Before you start
25
Initial settings
Laundry guidelines
Detergent drawer guidelines
25
26
28
Operations
31
Control panel
31
Simple steps to start
33
Dry clothes only
34
Course overview
35
Settings38
Maintenance
39
Eco Drum Clean
39
Smart Check
40
USING DRY COURSE
41
AIR WASH
42
Emergency drain
43
Cleaning44
Recovery from freezing
47
Care against an extended time of disuse
47
Troubleshooting
48
Checkpoints48
Information codes
53
Specifications
56
Fabric care chart
Protecting the environment
Specification sheet
56
57
58
2 English
WD80J6410AX-EN.indd 2
2015/2/7 11:39:00
Safety information
What you need to know about the safety instructions
Please read this manual thoroughly to ensure that you know how to safely and efficiently
operate the extensive features and functions of your new appliance. Please store the manual
in a safe location close to the appliance for future reference. Use this appliance only for its
intended purpose as described in this instruction manual.
Warnings and Important Safety Instructions in this manual do not cover all possible
conditions and situations that may occur. It is your responsibility to use common sense,
caution and care when installing, maintaining and operating your washing machine.
Because the following operating instructions cover various models, the characteristics of your
washing machine may differ slightly from those described in this manual and not all warning
signs may be applicable. If you have any questions or concerns, contact your nearest service
centre or find help and information online at www.samsung.com.
Safety information
Congratulations on your new Samsung washing machine. This manual contains important
information on the installation, use and care of your appliance. Please take some time to read
this manual to take full advantage of your washing machine’s many benefits and features.
Important safety symbols
What the icons and signs in this user manual mean:
WARNING
Hazards or unsafe practices that may result in severe personal injury, death and/or property
damage.
CAUTION
Hazards or unsafe practices that may result in personal injury and/or property damage.
NOTE
Indicates that a risk of personal injury or material damage exists.
English 3
WD80J6410AX-EN.indd 3
2015/2/7 11:39:01
Safety information
Safety information
These warning signs are here to prevent injury to yourself and others.
Please follow them explicitly.
After reading this manual, store it in a safe place for future reference.
Read all instructions before using the appliance.
As with any equipment that uses electricity and moving parts, potential hazards exist. To
safely operate this appliance, familiarize yourself with its operation and exercise care when
using it.
Important safety precautions
WARNING
To reduce the risk of fire, electric shock, or injury to persons when
using your appliance, follow basic precautions, including the following:
Do not let children (or pets) play in or on your washing machine.
The washing machine door does not open easily from the inside and
children may be seriously injured if trapped inside.
This appliance is not to be used by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not play with the
appliance.
For use in Europe: This appliance can be used by children aged from 8
years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved. Children shall not play
with the appliance. Cleaning and user maintenance shall not be made
by children without supervision.
4 English
WD80J6410AX-EN.indd 4
2015/2/7 11:39:01
This appliance should be positioned so that the power plug, the water
supply taps, and the drain pipes are accessible.
Safety information
If the supply cord is damaged, it must be replaced by the manufacturer,
its service agent or similarly qualified persons in order to avoid a
hazard.
For appliances with ventilation openings in the base, that a carpet must
not obstruct the openings.
The new hose-sets supplied with the appliance are to be used and that
old hose-sets should not be reused.
CAUTION
In order to avoid a hazard due to inadvertent resetting of the thermal
cut-out, this appliance must not be supplied through an external
switching device, such as a timer, or connected to a circuit that is
regularly switched on and off by the utility.
The tumble dryer is not to be used if industrial chemicals have been
used for cleaning.
The lint trap has to be cleaned frequently, if applicable.
Lint must not to be allowed to accumulate around the tumble dryer. (not
applicable for appliances intended to be vented to the exterior of the
building)
Adequate ventilation has to be provided to avoid the back flow of gases
into the room from appliances burning other fuels, including open fires.
Do not dry unwashed items in the tumble dryer.
Items that have been soiled with substances such as cooking oil,
acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and
wax removers should be washed in hot water with an extra amount of
detergent before being dried in the tumble dryer.
English 5
WD80J6410AX-EN.indd 5
2015/2/7 11:39:01
Safety information
Safety information
Items such as foam rubber (latex foam), shower caps, waterproof
textiles, rubber backed articles and clothes or pillows fitted with foam
rubber pads should not be dried in the tumble dryer.
Fabric softeners, or similar products, should be used as specified by the
fabric softener instructions.
The final part of a tumble dryer cycle occurs without heat (cool down
cycle) to ensure that the items are left at a temperature that ensures
that the items will not be damaged.
Remove all objects from pockets such as lighters and matches.
WARNING
Never stop a tumble dryer before the end of the drying cycle unless all
items are quickly removed and spread out so that the heat is dissipated.
Exhaust air must not be discharged into a flue which is used for
exhausting fumes from appliances burning gas or other fuels.
The appliance must not be installed behind a lockable door, a sliding
door or a door with a hinge on the opposite side to that of the tumble
dryer, in such a way that a full opening of the tumble dryer door is
restricted.
For use in Europe: Children of less than 3 years should be kept away
unless continuously supervised.
6 English
WD80J6410AX-EN.indd 6
2015/2/7 11:39:01
WARNING
The installation of this appliance must be performed by a qualified technician or service
company.
• Failure to do so may result in electric shock, fire, an explosion, problems with the product,
or injury.
Safety information
Critical installation warnings
The appliance is heavy, therefore take care when lifting it.
Plug the power cord into an AC 220 - 240 V / 50 Hz wall socket or higher and use the socket
for this appliance only. Never use an extension cord.
• Sharing a wall socket with other appliances using a power strip or extending the power
cord may result in electric shock or fire.
• Ensure that the power voltage, frequency, and current are the same as those of the
product specifications. Failure to do so may result in electric shock or fire. Plug the power
plug into the wall socket firmly.
Remove all foreign substances such as dust or water from the power plug terminals and
contact points using a dry cloth on a regular basis.
• Unplug the power plug and clean it with a dry cloth.
• Failure to do so may result in electric shock or fire.
• Plug the power plug into the wall socket so that the cord is running towards the floor.
If you plug the power plug into the socket in the opposite direction, the electric wires
within the cable may be damaged and this may result in electric shock or fire.
Keep all packaging materials out of the reach of children as these may be dangerous.
• If a child places a bag over its head, it may suffocate.
When the appliance, power plug or power cord is damaged, contact your nearest service
centre.
This appliance must be properly grounded.
Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line.
• This may result in electric shock, fire, an explosion, or problems with the product.
• Never plug the power cord into a socket that is not grounded correctly and make sure
that it is in accordance with local and national regulations.
Do not install this appliance near a heater or any inflammable material.
Do not install this appliance in a humid, oily or dusty location, or in a location exposed to
direct sunlight or water (rain drops).
Do not install this appliance in a location exposed to low temperatures.
• Frost may cause the tubes to burst.
English 7
WD80J6410AX-EN.indd 7
2015/2/7 11:39:01
Safety information
Safety information
Do not install this appliance in a location where gas may leak.
• This may result in electric shock or fire.
Do not use an electric transformer.
• This may result in electric shock or fire.
Do not use a damaged power plug, damaged power cord, or loose wall socket.
• This may result in electric shock or fire.
Do not pull or excessively bend the power cord.
Do not twist or tie the power cord.
Do not hook the power cord over a metal object, place a heavy object on the power cord,
insert the power cord between objects, or push the power cord into the space behind the
appliance.
• This may result in electric shock or fire.
Do not pull the power cord when unplugging the power plug.
• Unplug the power plug by holding the plug.
• Failure to do so may result in electric shock or fire.
8 English
WD80J6410AX-EN.indd 8
2015/2/7 11:39:01
Safety information
Installation cautions
CAUTION
This appliance should be positioned in such a way that the power plug is easily accessible.
• Failure to do so may result in electric shock or fire due to electric leakage.
Install your appliance on a solid, level floor that can support its weight.
• Failure to do so may result in abnormal vibrations, movement, noise, or problems with
the product.
Critical usage warnings
WARNING
If the appliance is flooded, turn off the water & power supplies immediately and contact your
nearest service centre.
• Do not touch the power plug with wet hands.
• Failure to do so may result in electric shock.
If the appliance generates a strange noise, a burning smell, or smoke, unplug the power plug
immediately and contact your nearest service centre.
• Failure to do so may result in electric shock or fire.
In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate immediately without
touching the power plug. Do not touch the appliance or power cord.
• Do not use a ventilating fan.
• A spark may result in an explosion or fire.
Do not let children play in or on the washing machine. In addition, when disposing of the
appliance, remove the washing machine door lever.
• If trapped inside the product, children may suffocate to death.
Make sure to remove the packaging (sponge, styrofoam) attached to the bottom of the
washing machine before using it.
Do not wash items contaminated with gasoline, kerosene, benzene, paint thinner, alcohol or
other inflammable or explosive substances.
• This may result in electric shock, fire, or an explosion.
Do not open the washing machine door by force while it is operating (high-temperature
washing/drying/spinning).
• Water flowing out of the washing machine may result in burns or cause the floor to be
slippery. This may result in injury.
English 9
WD80J6410AX-EN.indd 9
2015/2/7 11:39:01
Safety information
Safety information
•
Opening the door by force may result in damage to the product or injury.
Do not insert your hand under the washing machine while an operation is in progress.
• This may result in injury.
Do not touch the power plug with wet hands.
• This may result in electric shock.
Do not turn the appliance off by unplugging the power plug while an operation is in progress.
• Plugging the power plug into the wall socket again may cause a spark and result in
electric shock or fire.
Do not let children or the infirm use this washing machine without proper supervision. Do
not let children climb in or onto the appliance.
• This may result in electric shock, burns or injury.
Do not insert your hand or a metal object under the washing machine while it is operating.
• This may result in injury.
Do not unplug the appliance by pulling the power cord. Always grip the plug firmly and pull
it straight out of the outlet.
• Damage to the power cord may cause a short-circuit, fire and/or electric shock.
Do not attempt to repair, disassemble, or modify the appliance yourself.
• Do not use a fuse (such as copper, steel wire, etc.) other than a standard fuse.
• When the appliance needs to be repaired or reinstalled, contact your nearest service
centre.
• Failure to do so may result in electric shock, fire, problems with the product, or injury.
If the water supply hose comes loose from the water tap and floods the appliance, unplug the
power plug.
• Failure to do so may result in electric shock or fire.
Unplug the power plug when the appliance is not being used for long periods of time or
during a thunder or lightning storm.
• Failure to do so may result in electric shock or fire.
If any foreign substance enters into the appliance, unplug the power plug and contact you
nearest Samsung Customer Service.
• This may result in electric shock or fire.
10 English
WD80J6410AX-EN.indd 10
2015/2/7 11:39:01
Safety information
Usage cautions
CAUTION
When the washing machine is contaminated by a foreign substance such as detergent, dirt,
food waste, etc., unplug the power plug and clean the washing machine using a damp, soft
cloth.
• Failure to do so may result in discolouration, deformation, damage, or rust.
The front glass may be broken by a strong impact. Take care when using the washing
machine.
• If the glass is broken, it may result in injury.
After a water supply failure or when reconnecting the water supply hose, open the water tap
slowly.
Open the water tap slowly after a long period of non-use.
• The air pressure in the water supply hose or the water pipe may damage a product part
or result in a water leak.
If a draining error occurs during an operation, check if there is a draining problem.
• If the washing machine is used when it is flooded because of a draining problem, it may
result in electric shock or fire.
Insert the laundry into the washing machine completely so that the laundry does not get
caught in the door.
• If laundry gets caught in the door, it may result in damage to the laundry or the washing
machine, or result in a water leak.
Turn the water supply off when the washing machine is not being used.
Ensure that the screws on the water supply hose connector are properly tightened.
• Failure to do so may result in property damage or injury.
Ensure that the rubber seal and front door glass are not contaminated by a foreign substance
(e.g. waste, thread, hair, etc.).
• If a foreign substance is caught in the door or the door is not completely closed, it may
cause a water leak.
Open the water tap and check if the water supply hose connector is firmly tightened and that
there is no water leak before using the product.
• If the screws on the water supply hose connector are loose, it may result in a water leak.
The product you have purchased is designed for domestic use only.
English 11
WD80J6410AX-EN.indd 11
2015/2/7 11:39:01
Safety information
Safety information
Using the product for business purposes qualifies as a product misuse. In this case, the
product will not be covered by the standard warranty provided by Samsung and no
responsibility can be attributed to Samsung for malfunctions or damages resulting from such
misuse.
Do not stand on the appliance or place objects (such as laundry, lighted candles, lighted
cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.
• This may result in electric shock, fire, problems with the product, or injury.
Do not spray volatile material such as insecticide onto the surface of the appliance.
• As well as being harmful to humans, this may result in electric shock, fire or problems
with the product.
Do not place objects that generate electromagnetic fields near the washing machine.
• This may result in injury due to a malfunction.
Water drained during a high-temperature wash or drying cycle is hot. Do not touch the water.
• This may result in burns or injury.
Do not wash, spin, or dry water-proof seats, mats, or clothing (*) unless your appliance has a
special cycle for washing these items.
(*): Woollen bedding, rain covers, fishing vests, ski pants, sleeping bags, diaper covers, sweat
suits, and bicycle, motor cycle and car covers, etc.
• Do not wash thick or hard mats even if the washing machine mark is on the care label.
This may result in injury or damage to the washing machine, walls, floor, or clothing due
to abnormal vibrations.
• Do not wash throw rugs or doormats with rubber backing. The rubber backing may come
off and stick to inside the drum, and this may result in malfunction such as a drainage
error.
Do not operate the washing machine when the detergent drawer is removed.
• This may result in electric shock or injury due to a water leak.
Do not touch the insides of the drum during or just after drying as it is hot.
• This may result in burns.
Do not insert your hand into the detergent drawer.
• This may result in injury as your hand may be caught by the detergent input device.
• The liquid detergent guide (applicable models only) is not used for powder detergent.
Remove the guide when using powder detergent.
Do not place any objects (such as shoes, food waste, animals) other than laundry into the
washing machine.
• This may result in damage to the washing machine, or injury and death in the case of
pets due to the abnormal vibrations.
12 English
WD80J6410AX-EN.indd 12
2015/2/7 11:39:01
Do not wash laundry contaminated by oils, creams or lotions usually found in skincare shops
or massage clinics.
• This may cause the rubber seal to become deformed and result in a water leak.
Do not leave metal objects such as safety pins, hair pins or bleach in the drum for long
periods of time.
• This may cause the drum to rust.
• If rust starts appearing on the surface of the drum, apply a (neutral) cleansing agent to
the surface and use a sponge to clean it. Never use a metal brush.
Safety information
Do not press the buttons using sharp objects such as pins, knifes, fingernails, etc.
• This may result in electric shock or injury.
Do not use dry cleaning detergent directly and do not wash, rinse, or spin laundry
contaminated by dry cleaning detergent.
• This may result in spontaneous combustion or ignition due to the heat from the oxidation
of the oil.
Do not use water from water cooling/heating devices.
• This may result in problems with the washing machine.
Do not use natural hand-washing soap for the washing machine.
• If it hardens and accumulates inside the washing machine, it may result in problems with
the product, discolouration, rust, or bad odours.
Place socks and brassieres in a washing net and wash them with the other laundry.
Do not wash large laundry items such as bedding in the washing net.
• Failure to do so may result in injury due to abnormal vibrations.
Do not use hardened detergent.
• If it accumulates inside the washing machine, it may result in a water leak.
Make sure that the pockets of all the clothing items to be washed are empty.
• Hard, sharp objects such as coins, safety pins, nails, screws, or stones can cause extensive
damage to the appliance.
Do not wash clothing with large buckles, buttons or other heavy metal objects.
Sort the laundry by color on the basis of its colorfastness and select the recommended cycle,
water temperature and additional functions.
• This may result in discoloration or fabric damage.
Take care that children’s fingers are not caught in the door when you close it.
• Failure to do so may result in injury.
English 13
WD80J6410AX-EN.indd 13
2015/2/7 11:39:01
Safety information
Safety information
Critical cleaning warnings
WARNING
Do not clean the appliance by spraying water directly onto it.
Do not use the a strong acidic cleaning agent.
Do not use benzene, thinner or alcohol to clean the appliance.
• This may result in discolouration, deformation, damage, electric shock or fire.
Before cleaning or performing maintenance, unplug the appliance from the wall socket.
• Failure to do so may result in electric shock or fire.
Instructions about the WEEE
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
(Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that
the product and its electronic accessories (e.g. charger, headset,
USB cable) should not be disposed of with other household waste
at the end of their working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle
them responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where they
purchased this product, or their local government office, for details
of where and how they can take these items for environmentally
safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product and its electronic
accessories should not be mixed with other commercial wastes for
disposal.
14 English
WD80J6410AX-EN.indd 14
2015/2/7 11:39:01
Installation
Follow these instructions carefully to ensure proper installation of the washing machine and
to prevent accidents when doing laundry.
What’s included
01
02
Installation
Make sure all the parts are included in the product package. If you have a problem with
the washing machine or the parts, contact a local Samsung customer centre or the retailer.
09
03
10
11
04
05
12
06
07
08
01 Release lever
02 Detergent drawer
03 Control panel
04 Door
05 Drum
06 Lint filter
07 Emergency drain tube
08 Filter cover
09 Worktop
10 Power plug
11 Drain hose
12 Levelling feet
English 15
WD80J6410AX-EN.indd 15
2015/2/7 11:39:02
Installation
Bolt caps
Hose guide
Cold water hose
Hot water hose
Liquid detergent container
Installation
Spanner
Cap fixer
NOTE
•
•
•
Bolt caps : The provided number (3 to 6) of bolt caps depends on the model.
Hot water supply hose: Applicable models only.
Liquid detergent container: Applicable models only.
16 English
WD80J6410AX-EN.indd 16
2015/2/7 11:39:02
Installation requirements
Water supply
AC 220-240 V / 50 Hz fuse or circuit
breaker is required
• Use an individual branch circuit specific
to the washing machine
To ensure proper grounding, the washing
machine comes with a power cord featuring
a three-prong grounding plug for use in a
properly installed and grounded outlet.
Check with a qualified electrician or
serviceperson if you are not sure about the
grounding.
Do not modify the provided plug. If it does
not fit the outlet, call a qualified electrician
to install a proper outlet.
A proper water pressure for this washing
machine is between 50 kPa and 800 kPa.
Water pressure less than 50 kPa may cause
the water valve not to close completely. Or,
it may take longer to fill the drum, causing
the washing machine to turn off. Water taps
must be within 120 cm from the rear of the
washing machine so that the provided inlet
hoses reach the washing machine.
To reduce the risk of leaks:
• Make sure water taps are easily
accessible.
• Turn off the taps when the washing
machine is not in use.
• Check for any leaks at the water inlet
hose fittings on a regular basis.
•
WARNING
•
•
•
•
Do NOT use an extension cord.
Use only the power cord that comes
with the washing machine.
Do NOT connect the ground wire to
plastic plumbing, gas lines, or hot water
pipes.
Improperly connected grounding
conductors may cause electric shock.
Installation
Electrical supply and grounding
CAUTION
Before using the washing machine for the
first time, check all connections at the water
valve and taps for any leaks.
Drain
Samsung recommends a standpipe in
height of 60~90 cm. The drain hose must
be connected through the hose clip to the
standpipe, and the standpipe must fully
cover the drain hose.
English 17
WD80J6410AX-EN.indd 17
2015/2/7 11:39:02
Installation
Installation
Flooring
Alcove or closet installation
For best performance, the washing
machine must be installed on a solid floor.
Wood floors may need to be reinforced
to minimize vibration and/or unbalanced
loads. Carpeting and soft tile surfaces are
not a good resistance to vibrations and may
cause the washing machine to move slightly
during the spin cycle.
Minimum clearance for stable operation:
CAUTION
Do NOT install the washing machine on a
platform or a poorly supported structure.
Sides
25 mm
Rear
50 mm
Top
25 mm
Front
550 mm
If both the washing machine and a dryer
are installed in the same location, the front
of the alcove or closet must have at least
a 550 mm unobstructed air opening. Your
washing machine alone does not require a
specific air opening.
Water temperature
Do not install the washing machine in areas
where water may freeze as the washing
machine always retains some water in its
water valves, pumps, and/or hoses. Frozen
water left in the connection parts may
cause damage to belts, the pump, and other
components of the washing machine.
18 English
WD80J6410AX-EN.indd 18
2015/2/7 11:39:02
Step-by-step installation
STEP 1 Select a location
Installation
Location requirements:
• Solid, level surface without carpeting or flooring that may obstruct ventilation
• Away from direct sunlight
• Adequate room for ventilation and wiring
• The ambient temperature is always higher than the freezing point (0 ˚C)
• Away from a heat source
STEP 2 Remove the shipping bolts
Unpack the product package and remove all
shipping bolts.
1. Loosen all shipping bolts on the rear of
the machine using the supplied spanner.
2. Fill the holes with the supplied plastic
bolt caps.
Keep the shipping bolts for future use.
WARNING
Packaging materials can be dangerous to children. Dispose all packaging material (plastic
bags, polystyrene, etc.) out of children’s reach.
English 19
WD80J6410AX-EN.indd 19
2015/2/7 11:39:03
Installation
STEP 3 Adjust the levelling feet
Installation
1. Gently slide the washing machine into
position. Excessive force may damage
the levelling feet.
2. Level the washing machine by manually
adjusting the levelling feet.
3. When levelling is complete, tighten the
nuts using the spanner.
STEP 4 Connect the water hose
Connect the water supply hose to the
water tap.
A
1. Remove the adaptor (A) from the water
supply hose (B).
B
2. Use a Philips screwdriver to loosen four
screws on the adaptor.
20 English
WD80J6410AX-EN.indd 20
2015/2/7 11:39:03
3. Hold the adaptor and turn part (C) in the
arrow direction to loosen it by 5 mm (*).

C
Installation
C
4. Insert the adaptor into the water tap,
and tighten the screws while lifting up
the adaptor.
5. Turn part (C) in the arrow direction to
tighten it.
6. While holding down part (E), connect the
water supply hose to the adaptor. Then,
release part (E). The hose fits into the
adaptor with a clicking sound.
E
7. Connect the other end of the water
supply hose to the inlet valve on the
back of the washing machine. Turn the
hose clockwise to tighten.
English 21
WD80J6410AX-EN.indd 21
2015/2/7 11:39:04
Installation
Installation
8. Open the water tap and check if there
are any leaks around the connection
areas. If there are water leaks, repeat the
steps above.
•
If using a screw type of water tap,
connect the water hose to the water tap
as shown.
WARNING
Stop using the washing machine if there is a water leak, and contact a local Samsung service
centre. Otherwise, this may cause electric shock.
CAUTION
Do not stretch the water supply hose by force. If the hose is too short, replace the hose with
a longer, high-pressure hose.
NOTE
•
•
After connecting the water supply hose to the adaptor, check if it is connected properly
by pulling the water supply hose downwards.
Use a popular type of water taps. If the tap is square-shaped or too big, remove the
spacer ring before inserting the tap into the adaptor.
22 English
WD80J6410AX-EN.indd 22
2015/2/7 11:39:04
For models with an additional hot water
inlet:
Aqua hose (applicable models only)
Installation
1. Connect the red end of the hot water
supply hose to the hot water inlet on the
back of the machine.
2. Connect the other end of the hot water
supply hose to the hot water tap.
The aqua hose alerts users of a risk of water
leaks. It senses the water flow and turns red
on the centre indicator (A) in case of a leak.
A
English 23
WD80J6410AX-EN.indd 23
2015/2/7 11:39:04
Installation
STEP 5 Position the drain hose
The drain hose can be positioned in three ways:
Installation
Over the edge of a wash basin

The drain hose must be placed at a height
of between 60 cm and 90 cm (*) from the
floor. To keep the spout of the drain hose
bent, use the supplied plastic hose guide (A).
Secure the guide to the wall using a hook to
ensure stable drainage.
A
ln a sink drain pipe
The drain pipe must be above the sink
siphon so that the end of the hose is at least
60 cm above the floor.
ln a drain pipe

The drain pipe should be between 60 cm
and 90 cm high (*). It is advisable to use
a 65 cm high vertical pipe. Make sure the
drain hose is connected to the stand pipe at
a slant.
Drain standpipe requirements:
• Minimum diameter of 5 cm
• Minimum carry-away capacity of 60
litres per minute
STEP 6 Turn on the washing machine
Plug the power cord into a wall socket featuring an AC 220-240 V / 50 Hz approved electrical
outlet protected by a fuse or circuit breaker. Then, press the Power button to turn on the
washing machine.
24 English
WD80J6410AX-EN.indd 24
2015/2/7 11:39:05
Before you start
Initial settings
Run Calibration (recommended)
Calibration ensures accurate weight
detection by the washing machine. Make
sure the drum is empty before running
Calibration.
Before you start
1. Power off, and then power on the
washing machine.
2. Hold down Temp. and Delay End
simultaneously for 3 seconds to enter
Calibration mode. The “CB” message
appears.
3. Press Start/Pause to run the Calibration
cycle.
4. The drum will rotate clockwise and
counter-clockwise for about 3 minutes.
5. When the cycle is complete, “0” appears
on the display and the washing machine
will turn off automatically.
6. The washing machine is now ready for
use.
English 25
WD80J6410AX-EN.indd 25
2015/2/7 11:39:05
Before you start
Laundry guidelines
STEP 1 Sort
STEP 2 Empty pockets
Sort the laundry according to these
criteria:
Empty all the pockets of your laundry
items
Before you start
•
•
•
•
Care Label: Sort the laundry into cottons,
mixed fibres, synthetics, silks, wools, and
rayon.
Colour: Separate whites from colours.
Size: Mixing different-sized items
together in the drum improves the
washing performance.
Sensitivity: Wash delicate items
separately using an Easy Iron option for
pure, new woollen items, curtains, and
silk items. Check the labels on the items.
•
Turn clothing with buttons and
embroideries inside out
•
•
NOTE
Make sure to check the care label on the
clothing, and sort them accordingly before
starting the wash.
Metal objects such as coins, pins, and
buckles on clothing may damage other
laundry items as well as the drum.
If pants or jacket zippers are open while
washing, the drum may be damaged.
Zippers should be closed and fixed with
a string.
Clothing with long strings may become
entangled with other clothes. Make sure
to tie the strings before starting the
wash.
STEP 3 Use a laundry net
•
•
•
Brassieres (water washable) must be
placed in a laundry net. Metal parts of
the brassieres may break through and
tear other laundry items.
Small, light clothing such as socks,
gloves, stockings, and handkerchiefs
may become caught around the door.
Place them inside a fine laundry net.
Do not wash the laundry net by itself
without other laundry. This may cause
abnormal vibrations that could move the
washing machine and result in injury.
26 English
WD80J6410AX-EN.indd 26
2015/2/7 11:39:05
STEP 4 Prewash (if necessary)
Select the Prewash option for the selected
course if the laundry is heavily soiled. Do
not use the Prewash option when detergent
is manually added into the drum.
STEP 5 Determine the load capacity
The type of detergent depends on the type
of fabric (cotton, synthetic, delicate items,
wool), colour, wash temperature, and degree
of soiling. Always use “low suds” laundry
detergent, which is designed for automatic
washing machines.
NOTE
•
NOTE
When washing bedding or bedding covers,
the wash time may be lengthened or the
spin efficiency may be reduced. For bedding
or bedding covers, the recommended
maximum spin cycle speed is 800 rpm, and
the load capacity is 2.0 kg or less.
CAUTION
If the laundry is unbalanced and the “UE”
error code is displayed, redistribute the
load. Unbalanced laundry may reduce the
spinning performance.
•
Follow the detergent manufacturer’s
recommendations based on the weight
of the laundry, the degree of soiling, and
the hardness of the water in your local
area. If you are not sure about the water
hardness, contact a local water authority.
Do not use detergent that tends to be
hardened or solidified. This detergent
may remain after the rinse cycle,
blocking the drain outlet.
Before you start
Do not overload the washing machine.
Overloading may cause the washing
machine to not wash properly. For the load
capacity for the type of clothing, see page
35.
STEP 6 Apply a proper detergent
type
CAUTION
When washing wool using the wool course,
use only a neutral liquid detergent. If used
with the Wool course, powder detergent
may remain on the laundry and discolour
the laundry.
English 27
WD80J6410AX-EN.indd 27
2015/2/7 11:39:05
Before you start
Detergent drawer guidelines
The washing machine provides a three-compartment dispenser: the left compartment for the
main wash, the front-right for fabric softeners, and the rear-right for the preliminary wash.
01
Prewash detergent compartment
02
Main wash detergent compartment:
powder detergents, water softeners,
pre-soaking agents, bleach, and stain
removers
A
Before you start
03
Fabric softener compartment
CAUTION
•
•
•
Do not open the detergent drawer while the washing machine is operating.
Do not use the following types of detergent:
• Tablet or capsule types
• Ball or net types
To prevent the compartment clogging, concentrated or highly-enriched agents (fabric
softener or detergent) must be diluted with water before being applied.
The detergent drawer is located at the top-left corner of the washing machine.
1. Slide open the detergent drawer.
2. Apply laundry detergent to the
.
main-wash compartment as instructed
or recommended by the manufacturer.
To use liquid detergent, see page 31.
28 English
WD80J6410AX-EN.indd 28
2015/2/7 11:39:06
3. Apply an appropriate amount of fabric
softener to the front-right compartment
if necessary.
Do not exceed the max line (A) which is
marked on the compartment.
A
Before you start
4. If selecting the Prewash option, apply an
appropriate amount of detergent to the
.
rear-right compartment
5. Slide the detergent drawer inward to
close it.
Liquid detergent container (Applicable models only)
To use a liquid detergent, first put the
provided liquid detergent container in the
.
main wash detergent compartment
Then, apply an appropriate amount of
detergent to the container. Do not exceed
the max line which is marked on the inner
of the container.
CAUTION
Remove the liquid detergent container if
using a powder detergent.
English 29
WD80J6410AX-EN.indd 29
2015/2/7 11:39:06
Before you start
To use liquid detergent (applicable models only)
First insert the provided liquid container
in the
main-wash compartment. Then,
apply liquid detergent to the container
below the marked max line (A).
CAUTION
A
•
Before you start
•
Do not exceed the max line that is
marked inside the container.
Remove the liquid container if using
powder detergent.
30 English
WD80J6410AX-EN.indd 30
2015/2/7 11:39:06
Operations
Control panel
09
02
10
01
08
03
04
05
06
07
11
Turn the dial to select a cycle.
02 Display
The display shows current cycle information and estimated time
remaining, or an information code when a problem occurs.
03 Temp.
Press to change the water temperature for the current cycle.
04 Rinse
Press to change the rinse times for the current course.
You can set the rinse times up to 5.
05 Spin
Press to change the spinning speed for the current cycle.
: The final rinse process is suspended so that the
• Rinse Hold
laundry remains in the water. To unload the laundry, run a drain or
spin process.
• No Spin
: The drum does not spin after the final drain process.
06 Dry Level
Press this button to select proper drying option.
07 Bubble Soak
Press to activate/deactivate the Bubble Soak function. This function
helps remove a wide variety of stubborn stains.
08 Options
Press to select an Option from Intensive, Prewash, and
Intensive+Prewash. Press again to deselect.
Operations
01 Course
Selector
English 31
WD80J6410AX-EN.indd 31
2015/2/7 11:39:07
Operations
10 Power
Press to turn on/off the washing machine.
11 Start/Pause
Press to start or stop an operation.
Operations
09 Delay End
Delay End lets you set the end time of the current cycle. Based
on your settings, the start time of the cycle will be determined by
the machine’s internal logic. For example, this setting is useful for
programming your machine to finish a wash at the time you normally
return home from work.
• Press to choose a preset unit of hours.
32 English
WD80J6410AX-EN.indd 32
2015/2/7 11:39:07
Simple steps to start
2
1
6
4
3
7
5
Press the Power button to turn on the washing machine.
Turn the Course Selector to select a course.
Change the course settings (Temp., Rinse, Spin and Dry Level) as necessary.
To add an option, press the Options button repeatedly until the corresponding option
icon(s) turns on.
5. To select a preferred mode, press the Bubble Soak button repeatedly until the
corresponding mode icon turns on.
6. To add a frequent option, press the corresponding button (Delay End).
7. Press the Start/Pause button.
1.
2.
3.
4.
Operations
To change the course during operation
1. Press the Start/Pause button to stop operation.
2. Select a different course.
3. Press the Start/Pause button again to start the new course.
English 33
WD80J6410AX-EN.indd 33
2015/2/7 11:39:07
Operations
Dry clothes only
1
2
4
3
Operations
You can dry your clothes directly or dry the washed clothes according to the following
procedures.
1. Press Power button on the washing machine.
2. Use the Cycle Selector to select the appropriate drying cycle.
3. Press Dry Level button to select the appropriate drying mode.
4. Press Start/Pause button to start dry.
34 English
WD80J6410AX-EN.indd 34
2015/2/7 11:39:07
Course overview
Standard courses
Course
Description & Max load (kg)
Max
•
For blouses or shirts that are made of polyester
(diolen, trevira), polyamide (perlon, nylon), or the like.
3.5
•
Specific for machine-washable wool for loads less than
2.0 kg.
The wool course features gentle cradling and soaking
to protect the wool fibres from shrinkage/distortion.
A neutral detergent is recommended.
2
•
Featuring a high-temperature wash and extra rinses to
ensure that no powder detergent remains.
4
•
For outdoor clothes, skiwear, and sportswear that are
made of functional materials such as spandex, stretch,
and micro-fibre.
2
•
Featuring an additional rinse after applying fabric
softener to the laundry.
-
•
Cleans the drum by removing dirt and bacteria from
the drum.
Perform once every 40 washes with no detergent or
bleach applied.
Make sure the drum is empty.
Do not use any cleaning agents for cleaning the drum.
-
This course is useful for removing bad odors. Turning
the Cycle Selector cycles through the following
operating modes.(Deodorization > Sanitization)
Deodorization - Reduces bad smells from the laundry.
Sanitization - Deodorize and sanitize the laundry by
stronger AIR Wash action with higher temp.
-
COTTON
SYNTHETICS
WOOL
•
•
BABY CARE
OUTDOOR CARE
RINSE + SPIN
ECO DRUM CLEAN
•
•
•
•
AIR WASH
•
•
Operations
For cottons, bed linens, table linens, underwear, towels,
or shirts.
The washing time and the number of rinse cycles are
automatically adjusted according to the load.
•
English 35
WD80J6410AX-EN.indd 35
2015/2/7 11:39:08
Operations
Course
COTTON DRY
SYNTHETICS DRY
SUPER ECO WASH
Description & Max load (kg)
•
Use to dry laundry such as cotton, underwear, and
linen.
-
•
Use to dry heat-sensitive garments. This protects the
fibers of the garment by dying it at low temperatures.
-
•
Low-temperature Eco Bubble contributes to power
saving.
4
•
Press this button if you need to shorten the washing
time, applicable for Intensive, Pre Wash, or Delay End
cycles. The shortened time may differ depending on
the Cycle/Load/Option.
5
For lightly soiled garments in less than 2.0 kg that you
want to wash quickly.
2
SUPER SPEED
Operations
15’ QUICK WASH
•
Options
Option
Intensive
Pre Wash
Description
•
For badly soiled laundry. The operation time for each cycle is
longer than normal.
•
This will add a preliminary washing cycle before the main
wash cycle.
•
•
Bubble Soak helps remove a variety of stubborn stains.
With Bubble Soak selected, laundry is thoroughly soaked in
water bubbles for effective washing.
Bubble Soak is available with and adds up to 30 minutes (or
20 minutes) to 3 cycles: Cotton, Synthetics, and Baby Care.
Bubble Soak
•
•
Use this option to dry the laundry for the specifiedperiod of
time depending on the fibes, amount of laundry quantity and
moisture.
•
Use this option to dry laundry such as cotton, underwear, and
linen.
•
The displayed time refers to the end time of a selected course.
Time Dry
Cupboard
Delay End
36 English
WD80J6410AX-EN.indd 36
2015/2/7 11:39:08
Delay End
You can set the washing machine to finish our wash automatically at a later time, choosing a
delay of between 1 to 19 hours (in 1 hour increments). The hour displayed indicates the time
the wash will finish
1. Select a course. Then change the course settings if necessary.
2. Press the Delay End button repeatedly until a desired end time is set.
3. Press Start/Pause button.
The corresponding indicator turns on with the clock running.
4. To cancel the Delay End, restart the washing machine by pressing the POWER button.
Use case
You want to finish a two-hour course 3 hours later from now. For this, you add the Delay End
option to the current course with the 3-hour setting, and press the Start/Pause button at 2:00
p.m. Then, what happens? The washing machine starts operating at 3:00 p.m., and ends at
5:00 p.m. Provided below is the time line for this example.
3:00 pm
Start
5:00 pm
End
Operations
2:00 pm
Set the Delay End to 3 hours
English 37
WD80J6410AX-EN.indd 37
2015/2/7 11:39:09
Operations
Operations
Settings
Child Lock
Sound On/Off
To prevent accidents involving children, the
Child Lock function locks all buttons.
However, Child Lock does not activate until
you press Start/Pause.
In the holding state, you can open the
door or change settings by pressing
corresponding buttons. However, once
you press Start/Pause to start the washing
machine, the Child Lock will be reactivated.
• Child Lock locks all buttons except for
Power.
• To activate or deactivate Child Lock, hold
down Temp. and Rinse simultaneously
for 3 seconds.
You can turn on or off the key tone, beep,
or alarm. Your setting will remain effective
after you restart the machine.
• To mute the sound, hold down the Rinse
and Spin buttons simultaneously for 3
seconds. The [icon] indicator turns on.
• To unmute the sound, hold down again
for 3 seconds.
NOTE
To add detergent, put more laundry in the
drum, or change the cycle settings whilst
in the Child Lock state, you must first
deactivate the Child Lock.
38 English
WD80J6410AX-EN.indd 38
2015/2/7 11:39:09
Maintenance
Keep the washing machine clean to prevent deteriorated performance and to preserve its life
cycle.
Eco Drum Clean
Perform this course regularly to clean the
drum and to remove bacteria from it.
1. Press the Power button to turn on
washing machine.
2. Turn the Course Selector to select ECO
DRUM CLEAN.
3. Press the Start/Pause button.
NOTE
The water temperature for ECO DRUM
CLEAN is set to 70 °C, which cannot be
changed.
ECO DRUM CLEAN reminder
•
•
The ECO DRUM CLEAN reminder appears
on the main screen once every 40
washes. It is advisable to perform the
ECO DRUM CLEAN regularly.
When you first see this reminder,
you can ignore the reminder for 6
consecutive times. From the 7th wash,
the reminder does not appear. However,
it appears again on the second 40th
wash.
CAUTION
Do not use any cleaning agents for cleaning
the drum. Chemical residue in the drum
deteriorates the washing performance.
Maintenance
English 39
WD80J6410AX-EN.indd 39
2015/2/7 11:39:09
Maintenance
Smart Check
To enable this function, you must first download the Samsung Smart Washer at the Play Store
or the Apple Store, and install it on a mobile device featuring the camera operation.
Maintenance
The Smart Check function has been
optimized for Galaxy & iPhone series
(applicable models only).
1. Press and hold the Spin and Dry Level
buttons simultaneously for 3 seconds to
enter the Smart Check mode.
2. The washing machine starts the selfdiagnosis procedure and display
an information code if a problem is
detected.
3. Run the Samsung Smart Washer app
on your mobile device, and tap Smart
Check.
4. Put the mobile device close to the
washing machine’s display so that the
mobile device and the washing machine
face each other. Then, the information
code will be recognized automatically by
the app.
5. When the information code is
recognized correctly, the app provides
detailed information about the problem
with applicable counteractions..
NOTE
•
The function name, Smart Check, may
differ depending on the language.
•
If the washing machine reflects light
on the display, the app may fail to
recognize the information code.
•
If the app fails to recognize the Smart
Check code consecutively, enter the
information code manually onto the app
screen.
40 English
WD80J6410AX-EN.indd 40
2015/2/7 11:39:09
USING DRY COURSE
All drying options except for the Time Dry option detect the weight of the laundry in order to
display a more accurate drying time and dry the laundry more effectively.
Refer to the chart below to select the appropriate drying option according to the type and
amount of laundry and the moisture you want to leave.
Mode
Drying option
Usage
Auto Drying
Cupboard
Time Dry
Manual Drying
Load capacity(kg)
Cotton Dry
Synthetics Dry
Use this option to dry laundry such
as cotton, underwear, and linen.
5 kg
3 kg
Use this option to dry the laundry
for the specified peiod of time
depending on the fibes, amount of
laundry quantity and moisture.
30 ~ 270 min.
(in 30 minutes
increments).
30 ~ 270 min.
(in 30 minutes
increments).
NOTE
The drying result may differ depending
on the selected washing cycle and the
type/amount of laundry.
•
If both washing and drying cycles are
selected, the spin speed is automatically
set to enhance the drying efficiency.
•
•
•
Do not use the drying function after
applying a chlorine bleach agent to the
laundry during a wash or drying cycle.
Otherwise, the laundry may become
discolored or the material may be
damaged.
In case you want to dry laundry after
a hand wash, turn the cycle selector to
select the spin cycle, and then select a
drying option for best performance.
•
Do not use the drying function for
clothing with fur lining or made from
acrylic material. This may result in the
drying function being degraded.
When drying is complete, dust from
the dry surface of the clothes may
remain on the diaphragm due to the
ironing effect that prevents wrinkles.
The dus will be washed away during the
following wash. Alternatively, you can
easily remove it with a damp towel or
cloth.
•
Do not touch the insides of the drum or
the washing machine surface during or
just after drying as it may be hot. This
may result in burns.
Maintenance
•
CAUTION
English 41
WD80J6410AX-EN.indd 41
2015/2/7 11:39:09
Maintenance
AIR WASH
The Air Wash function refreshes garments through Samsung’s unique air-washing
technology without the need for water.
Refer to the chart below for the usage and cycle time of each Air Wash cycle.
Cycle
Usage
Cycle time
Deodorization
Use this cycle to remove bad odors from the
laundry.
29min
Sanitization
Use this cycle to remove bad odors and bacteria
from the laundry.
59min
NOTE
•
The recommended maximum load
capacity for the Air Wash cycles is 1
kg or less (one or two items). If you
overload the drum,, the deodorization or
sanitization efficiey may be reduced.
•
You can add a fragrance sheet to the
laundry to add fragrance during the Air
Wash cycle.
Maintenance
CAUTION
Do not use any Air Wash cycles for the
following items
•
Heat-sensitive garments made from
leather, mink, fur, silk, etc.
•
Underwear trimmed with lace, doll
cushions, and trims on dress suits may
become loose.
•
Clothes trimmed with buttons can cause
them to break.
•
Clothes full of starch may become
deformed.
•
Hard bedding
•
Electric blankets, furry or bulky blankets
•
Latex pillows
42 English
WD80J6410AX-EN.indd 42
2015/2/7 11:39:09
Emergency drain
In case of a power failure, drain the water inside the drum before taking out the laundry.
1. Power off and unplug the washing
machine from the electrical outlet.
2. Open the filter cover (A) using a coin or
thin metal object.
A
3. Put an empty, spacious container around
the cover, and stretch the emergency
drain tube to the container while holding
the tube cap (B).
B
Maintenance
C
4. Open the tube cap and let water in the
tube (C) flow into the container.
5. When done, close the tube cap, and
reinsert the tube. Then, close the filter
cover.
NOTE
Use a spacious container because the water
in the drum may be more than expected.
English 43
WD80J6410AX-EN.indd 43
2015/2/7 11:39:09
Maintenance
Cleaning
Surface of the washing machine
Use a soft cloth with a nonabrasive household detergent. Do not spray water onto the
washing machine.
Mesh filter
Clean the mesh filter of the water supply hose once or twice a year.
1. Turn off the washing machine, and
unplug the power cord.
2. Close the water tap.
3. Loosen and disconnect the water supply
hose from the back of the washing
machine. Cover the hose with a cloth to
prevent water from gushing out.
Maintenance
4. Use pliers to pull out the mesh filter
from the inlet valve hole.
5. Submerge the mesh filter deeply in
water so that the threaded connector is
also submerged.
6. Dry the mesh filter completely in the
shade.
7. Reinsert the mesh filter into the water
supply hose, and place the water supply
hose in the original position.
8. Open the water tap.
NOTE
If the mesh filter is clogged, an error code of “4C” appears on the screen.
44 English
WD80J6410AX-EN.indd 44
2015/2/7 11:39:10
Debris filter
It is advisable to clean the debris filter 5 or 6 times a year to prevent its clogging. A clogged
debris filter may reduce the bubble effect.
A
1. Turn off the washing machine, and
unplug the power cord.
2. Drain the remaining water inside the
drum drum. See the “Emergency drain”
section.
3. Open the filter cover using a coin or key.
4. Turn the pump filter (A) knob to the left,
and drain off the remaining water.
5. Clean the pump filter using soft brushes.
Make sure the drain pump propeller
inside the filter is unclogged.
6. Reinsert the pump filter, and turn the
filter knob to the right.
•
•
Some pump filters feature a safety knob
that is designed to prevent accidents
by children. To open the safety knob
of the pump filter, push in and turn it
anticlockwise. The spring mechanism of
the safety knob helps open the filter.
To close the safety knob of the pump
filter, turn it clockwise. The spring makes
a rattling sound, which is normal.
Maintenance
NOTE
NOTE
If the debris filter is clogged, an error code of “5C” appears on the screen.
English 45
WD80J6410AX-EN.indd 45
2015/2/7 11:39:10
Maintenance
CAUTION
•
•
Make sure the filter cap is closed properly after cleaning the filter. Otherwise, this may
cause a leak.
Make sure the filter is inserted properly after cleaning it. Otherwise, this may cause an
operational failure or a leak.
Detergent Drawer
A
1. While holding down the release lever (A)
on the inner of the drawer, slide open
the drawer.
2. Remove the release lever and the liquid
detergent container from the drawer.
Maintenance
3. Clean the drawer components in flowing
water using a soft brush.
4. Clean the drawer recess using a soft
brush.
5. Reinsert the release lever and the liquid
detergent container to the drawer.
6. Slide the drawer inward to close it.
46 English
WD80J6410AX-EN.indd 46
2015/2/7 11:39:11
NOTE
To remove remaining detergent, perform the RINSE+SPIN course with the drum being empty.
Recovery from freezing
The washing machine may freeze when it drops below 0 °C.
1.
2.
3.
4.
5.
Turn off the washing machine, and unplug the power cord.
Pour warm water over the water tap to loosen the water supply hose.
Disconnect the water supply hose, and soak it in warm water.
Pour warm water into the drum and leave it for about 10 minutes.
Reconnect the water supply hose to the water tap.
NOTE
If the washing machine still doesn’t operate normally, repeat the above steps until it operates
normally.
Care against an extended time of disuse
Avoid leaving the washing machine unused for an extended time.
If this is the case, drain the washing machine and unplug the power cord.
Turn the Course Selector to select a RINSE+SPIN.
Empty the drum, and press Start/Pause button.
When the course is complete, close the water tap and disconnect the water supply hose.
Turn off the washing machine, and unplug the power cord.
Open the door to let air circulate through the drum.
Maintenance
1.
2.
3.
4.
5.
English 47
WD80J6410AX-EN.indd 47
2015/2/7 11:39:11
Troubleshooting
Checkpoints
If you encounter a problem with the washing machine, first check the table below and try the
suggestions.
Problem
Action
•
Make sure the washing machine is plugged in.
Make sure the door is properly closed.
Make sure the water taps are open.
Make sure to press or tap Start/Pause to start the washing
machine.
Make sure Child Lock is not activated.
Before the washing machine starts to fill, it will make a series
of clicking noises to check the door lock and does a quick
drain.
Check the fuse or reset the circuit breaker.
•
•
•
•
•
Fully open the water tap.
Make sure the door is properly closed.
Make sure the water supply hose is not frozen.
Make sure the water supply hose is not kinked or clogged.
Make sure there is sufficient water pressure.
•
Make sure the washing machine is running with sufficient
water pressure.
Make sure the detergent is added to the centre of the
detergent drawer.
Make sure the rinse cap is inserted properly.
If using granular detergent, make sure the detergent selector
is in the upper position.
Remove the rinse cap and clean the detergent drawer.
•
•
•
•
Does not start.
Water supply is
insufficient, or no
water is supplied.
Troubleshooting
Troubleshooting
After a cycle,
detergent remains in
the detergent drawer.
•
•
•
•
•
•
48 English
WD80J6410AX-EN.indd 48
2015/2/7 11:39:11
Problem
Action
•
Excessive vibrations
or makes noise.
•
•
•
•
•
•
•
•
•
Does not drain and/ or
spin.
•
•
•
•
The door does not
open.
•
•
•
Make sure the drain hose is straightened all the way to the
drain system. If you encounter a drain restriction, call for
service.
Make sure the debris filter is not clogged.
Close the door and press or tap Start/Pause. For your safety,
the washing machine will not tumble or spin unless the door
is closed.
Make sure the drain hose is not frozen or clogged.
Make sure the drain hose is connected to a drain system that
is not clogged.
If the washing machine is not supplied with sufficient power,
the washing machine temporarily will not drain or spin.
As soon as the washing machine regains sufficient power, it
will operate normally.
Troubleshooting
•
•
Make sure the washing machine is installed on a level, solid
floor that is not slippery.
If the floor is not level, use the levelling feet to adjust the
height of the washing machine.
Make sure the shipping bolts are removed.
Make sure the washing machine is not contacting any other
object.
Make sure the laundry load is balanced.
The motor can cause noise during normal operation.
Overalls or metal-decorated clothes can cause noise while
being washed. This is normal.
Metal objects such as coins can cause noise. After washing,
remove these objects from the drum or filter case.
Press or tap Start/Pause to stop the washing machine.
It may take a few moments for the door lock mechanism to
disengage.
The door will not open until 3 minutes after the washing
machine has stopped or the power turned off.
Make sure all the water in the drum is drained.
The door may not open if water remains in the drum. Drain
the drum and open the door manually.
Make sure the door lock light is off. The door lock light turns
off after the washing machine has drained.
English 49
WD80J6410AX-EN.indd 49
2015/2/7 11:39:11
Troubleshooting
Problem
Action
•
•
Excessive suds.
•
•
•
•
Cannot apply
additional detergent.
•
•
•
•
•
Stops.
•
Troubleshooting
Troubleshooting
•
•
Make sure the Auto Detergent and Auto Softener settings are
properly configured.
Make sure you use the recommended types of detergent as
appropriate.
Use high efficiency (HE) detergent to prevent oversudsing.
Reduce the detergent amount for soft water, small loads, or
lightly soiled loads.
Non-HE detergent is not recommended.
Make sure the remaining amount of detergent and fabric
softener is not over the limit.
Make sure the Auto Dispense function is activated, with both
the Water Hardness and Concentration settings properly
specified.
Plug the power cord into a live electrical outlet.
Check the fuse or reset the circuit breaker.
Close the door and press or tap Start/Pause to start the
washing machine.
For your safety, the washing machine will not tumble or spin
unless the door is closed.
Before the washing machine starts to fill, it will make a series
of clicking noises to check the door lock and does a quick
drain.
There may be a pause or soak period in the cycle. Wait briefly
and the washing machine may start.
Make sure the mesh filter of the water supply hose at the
water taps are not clogged. Periodically clean the mesh filter.
If the washing machine is not supplied with sufficient power,
the washing machine temporarily will not drain or spin. As
soon as the washing machine regains sufficient power, it will
operate normally.
50 English
WD80J6410AX-EN.indd 50
2015/2/7 11:39:11
Problem
Action
•
•
•
•
•
Fills with the wrong
water temperature.
•
•
Load is wet at the end
of a cycle.
•
•
•
•
Fully open both taps.
Make sure the temperature selection is correct.
Make sure the hoses are connected to the correct taps. Flush
water lines.
Make sure the water heater is set to supply a minimum
120 °F (49 °C) hot water at the tap. Also, check the water
heater capacity and recovery rate.
Disconnect the hoses and clean the mesh filter. The mesh filter
may be clogged.
While the washing machine fills, the water temperature may
change as the automatic temperature control feature checks
incoming water temperature. This is normal.
While the washing machine fills, you may notice just hot and/
or just cold water going through the dispenser when cold or
warm temperatures are selected.
This is a normal function of the automatic temperature
control feature as the washing machine determines the water
temperature.
Use the High or Extra High spin speed.
Use high efficiency (HE) detergent to reduce oversudsing.
Load is too small. Small loads (one or two items) may become
unbalanced and not spin completely.
Make sure the drain hose is not kinked or clogged.
Has odours.
•
•
•
•
Excessive suds collect in recesses and can cause foul odours.
Run cleansing cycles to sanitize periodically.
Clean the door seal (diaphragm).
Dry the washing machine interior after a cycle has finished.
No bubbles are seen
(Bubbleshot models
only).
•
•
Overloading may screen bubbles.
Severely contaminated laundry may not generate bubbles.
Leaks water.
Troubleshooting
•
•
Make sure the door is properly closed.
Make sure all hose connections are tight.
Make sure the end of the drain hose is correctly inserted and
secured to the drain system.
Avoid overloading.
Use high efficiency (HE) detergent to prevent oversudsing.
•
•
•
English 51
WD80J6410AX-EN.indd 51
2015/2/7 11:39:11
Troubleshooting
Problem
Action
•
Wi-Fi does not work
(Wi-Fi models only).
•
•
Make sure the Internet connection to your house is properly
established.
Make sure the router turns on and operates normally.
Make sure you have installed the latest version of the Smart
Control App.
Troubleshooting
Troubleshooting
If a problem persists, contact a local Samsung service centre.
52 English
WD80J6410AX-EN.indd 52
2015/2/7 11:39:11
Information codes
If the washing machine fails to operate, you may see an information code on the screen.
Check the table below and try the suggestions.
Problem
4C
Action
Water is not supplied.
• Make sure the water taps are open.
• Make sure the water hoses are not clogged.
• Make sure the water taps are not frozen.
• Make sure the washing machine is operating with sufficient
water pressure.
• Make sure that the cold water tap and the hot water tap are
properly connected.
• Clean the mesh filter as it may be clogged.
NOTE
When the washer displays the “4C” code, the washer do
draining for 3 minutes. During this time, the Power button is
inoperative.
•
4C2
Make sure the cold water supply hose is firmly connected to
the cold water tap.
If it is connected to the hot water tap, the laundry may be
deformed with some cycles.
DC
Operating the washer with the door open.
• Make sure the door is properly closed.
• Make sure laundry is not caught in the door.
OC
Water is overflowed.
• Restart after spinning.
• If the information code remains on the display, contact a local
Samsung service centre.
Troubleshooting
5C
Water is not draining.
• Make sure the drain hose is not frozen or clogged.
• Make sure the drain hose is positioned correctly, depending
on the connection type.
• Clean the debris filter as it may be clogged.
• Make sure the drain hose is straightened all the way to the
drain system.
• If the information code remains, contact a customer service
centre.
English 53
WD80J6410AX-EN.indd 53
2015/2/7 11:39:11
Troubleshooting
Problem
LC
Action
Check the drain hose.
• Make sure the end of the drain hose is placed on the floor.
• Make sure the drain hose is not clogged.
• If the information code remains, contact a customer service
centre.
NOTE
When the washer displays the “LC”/“LC1” code, the washer do
draining for 3 minutes. During this time, the Power button is
inoperative.
LC1
UB
Spinning does not work.
• Make sure laundry is spread out evenly.
• Make sure the washing machine is on a flat, stable surface.
• Redistribute the load. If only one item of clothing needs
washing, such as a bathrobe or pair of jeans, the final spin
result might be unsatisfactory, and an “UB” check message
will be shown in the display.
3C
Check the motor for operation.
• Try restarting the cycle.
• If the information code remains, contact a customer service
centre.
The electronic control needs to be checked (Over Voltage Error).
•
•
•
Troubleshooting
Troubleshooting
UC
Check the PCB and wire harness.
Check if power is supplied properly
If the information code remains, contact a customer service
centre.
Low voltage detected.
•
•
HC
Check if the power cord is plugged in.
If the information code remains, contact a customer service
centre.
High temperature heating check.
• If the information code remains, contact a customer service
centre.
54 English
WD80J6410AX-EN.indd 54
2015/2/7 11:39:11
Problem
1C
Action
The Water Level sensor is not working properly.
• Try power off and restarting the cycle.
• Check Water Level Sensor wire harness.
• If the information code remains, contact a customer service
centre.
NOTE
When the washer displays the “1C” code, the washer do
draining for 3 minutes. During this time, the Power button is
inoperative.
AC
Check communications between main and sub PBAs.
• Try power off and restarting the cycle.
• If the information code remains, contact a customer service
centre.
If any information code keeps appearing on the screen, contact a local Samsung service
centre.
Troubleshooting
English 55
WD80J6410AX-EN.indd 55
2015/2/7 11:39:11
Specifications
Fabric care chart
The following symbols provide garment care directions. The care labels include four symbols
in this order: washing, bleaching, drying and ironing (and dry cleaning when necessary).
The use of symbols ensures consistency among garment manufacturers of domestic and
imported items. Follow the care label directions to maximize garment life and reduce laundry
problems.
Resistant material
Do not iron
Delicate fabric
Can be dry cleaned using any
solvent
Item can be washed at 95 ˚C
Dry Clean
Item can be washed at 60 ˚C
Dry clean with perchloride,
lighter fuel, pure alcohol or
R113 only
Item can be washed at 40 ˚C
Dry clean with aviation fuel,
pure alcohol or R113 only
Item can be washed at 30 ˚C
Do not dry clean
Hand wash only
Dry flat
Dry clean only
Can be hung to dry
Can be bleached in cold water
Dry on clothes hanger
Do not bleach
Tumble dry, normal heat
Can be ironed at 200 ˚C max
Tumble dry, reduced heat
Can be ironed at 150 ˚C max
Do not tumble dry
Specification
Can be ironed at 100 ˚C max
56 English
WD80J6410AX-EN.indd 56
2015/2/7 11:39:14
Protecting the environment
•
•
•
•
This appliance is manufactured from recyclable materials. If you decide to dispose of this
appliance, please observe local waste disposal regulations. Cut off the power cord so that
the appliance cannot be connected to a power source. Remove the door so that animals
and small children cannot get trapped inside the appliance.
Do not exceed the detergent quantities recommended in the detergent manufacturer’s
instructions.
Use stain removal products and bleaches before the wash cycle only when strictly
necessary.
Save water and electricity by only washing full loads (the exact amount depends upon the
program used).
Specification
English 57
WD80J6410AX-EN.indd 57
2015/2/7 11:39:14
Specification
Specification sheet
“ * ” Asterisk(s) means variant model and can be varied (0-9) or (A-Z).
Type
Front loading washing machine
Model name
WD90J6*****
WD80J6*****
Dimensions
W600 x D650 x
H850 (mm)
W600 x D600 x
H850 (mm)
Water pressure
50 kPa ~ 800 kPa
Water volume
63 L
58 L
NET weight
70 kg
71 kg
Wash and spin capacity
9.0 kg
8.0 kg
Dry Capacity
6.0 kg
6.0 kg
220 V
100 W
240 V
100 W
220 V
2000 W
240 V
2400 W
220 V
1600 W
240 V
1600 W
220 ~ 240 V
450 W
Washing
Power
consumption
Washing and
heating
Drying
Spin
Pumping
Spin revolutions
30 W
1400 rpm
NOTE
Specification
The design and specifications are subject to change without notice for quality improvement
purposes.
58 English
WD80J6410AX-EN.indd 58
2015/2/7 11:39:14
According to Regulation (EU) No. 90/60/EC
“ * ” Asterisk(s) means variant model and can be varied (0-9) or (A-Z).
Samsung
Model Name
WD90J6*****
WD80J6*****
A
A
Energy Efficiency Class
A (highest efficient) to G (lowest efficient)
Energy Consumption
Washing, spinning, and drying
kWh
6.12
5.44
Washing and spinning only
kWh
1.17
1.04
A
A
A
A
%
44
44
rpm
1400
1400
Washing
kg
9
8
Drying
kg
6
6
Washing Performance Class
A (highest efficient) to G (lowest efficient)
Water Extraction Efficiency Class
A (highest efficient) to G (lowest efficient)
Residual moisture
Maximum Spin Speed
Capacity
Water Consumption
Washing, spinning, and drying
ℓ
99
88
Washing and spinning only
ℓ
54
44
Washing, spinning, and drying
min
592
517
Washing and spinning only
min
262
262
Program Duration
Programs to which the information on the label
and the Sheet relate
Wash
Cotton 60 ºC + Intensive
Dry
Cotton Dry + Cup board
Estimatd annual consumption for a 4-person household, always using the dries (200 cycles)
Energy Consumption
kWh/yr
1224
1088
Water Consumption
ℓ
19800
17600
Energy Consumption
kWh/yr
234
208
Water Consumption
ℓ
10800
9600
Specification
Estimatd annual consumption for a 4-person household, never using the drier (200 cycles)
English 59
WD80J6410AX-EN.indd 59
2015/2/7 11:39:14
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
UK
0330 SAMSUNG (7267864)
www.samsung.com/uk/support
DC68-03591A-00_EN
WD80J6410AX-EN.indd 60
2015/2/7 11:39:15