- Industrial & lab equipment
- Electrical equipment & supplies
- Batteries & accessories
- Battery chargers
- Anton/Bauer
- 84750102
- Owner's manual
Anton/Bauer 84750102 Owner's manual
Add to my manuals7 Pages
Anton/Bauer 84750102 is a three-hour fast charger designed solely for the CINE VCLX/2 battery system, employing the Logic Series circuits used in every Anton/Bauer charger. This lightweight (2.5 lbs.) charger features the InterActive charge programming that provides all charge termination and protection routines for safe, dependable charging.
advertisement
Approved Copy
One
Wor ld. O ne S mar t Ch oice
.
™
®
CINE VCLX/2 CHARGER
Only for use with CINE VCLX/2 battery
Owner’s Manual
7595-0339 Rev. B
1 INTRODUCTION
FEATURES
SAFEGUARDS
GROUNDING/EARTHING
CHARGING
APPLICATIONS
2 THREE STAGE CHARGING METHODOLOGY
LED INDICATIONS
3 FCC NOTICE
SPECIFICATIONS
FUSE/TYPE REPLACEMENT
4 WARRANTY
GROUNDING/EARTHING
The CINE VCLX/2 charger is a three (3) hour fast charger designed specially for the CINE VCLX/2 battery system. It incorporates all of the
Logic Series® circuits that are employed in every Anton/Bauer charger.
The InterActive® charge programming provides all charge termination and protection routines for safe, reliable, chemistry independent charging.
IMPORTANT WARNING: THIS APPARATUS MUST BE EARTHED.
To ensure safe operation, the three pin plug supplied must be inserted only into a standard three-pin power point which is effectively grounded through the normal household wiring. Extension cords used with the equipment must be three-conductor and be correctly wired to provide connection to earth ground. Improperly wired extension cords are a dangerous electrical hazard.
Like all Anton/Bauer chargers, everything is automatic. Once a battery is plugged into the charger, it will automatically go into the charging mode.
FEATURES
The fact that the equipment operates satisfactorily does not imply that the power point is properly grounded and that the installation is completely safe. If any doubt exists about the correct grounding of the power point, consult a qualified electrician.
• Three (3) hour charge time
• Red and Green status LED’s
IMPORTANT: The wires in this mains lead are colored in accordance with the following code:
•
•
Wide Range Input (100-240vac 50/60Hz)
Six (6) Independent Charge Termination Systems
Green and Yellow
Blue
Brown
Earth
Neutral
Live
• Lightweight (2.5lbs.)
SAFEGUARDS CHARGING
Power Sources: This unit was designed to operate at mains volt
ages from 100 to 240 Volts AC, 50-60 Hz.
Important: When powering charger using a generator, the generator
must produce a sine wave or modified sine wave output,
otherwise charger may be damaged.
Risk of Electrical Shock: Refer servicing to qualified service per-
sonnel.
As with all Anton/Bauer chargers, charging with CINE VCLX/2 charger is fully automatic. Attach the CINE VCLX/2 battery to the CINE VCLX/2 charger and it will automatically determine the appropriate charge routine and execute it.
APPLICATIONS
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
UNIT TO RAIN OR MOISTURE.
NOTE: A battery can remain on an Anton/Bauer charger indefinitely.
The CINE VCLX/2 charger incorporates the exclusive InterActive communication between battery and charger, which allows the charger to identify an Anton/
Bauer battery when attached and determine the precise charge routine for that battery under the prevailing conditions.
WARNING: USE OF THIS CHARGER WITH ANY BATTERY NOT
MANUFACTURED BY ANTON/BAUER MAY RESULT
IN BATTERY DAMAGE AND CAUSE RISK OF FIRE
OR PERSONAL INJURY. ANTON/BAUER ACCEPTS
NO RESPONSIBILITY FOR ANY INJURY OR DAMAGE
ASSOCIATED WITH THE USE OF BATTERIES NOT
MANUFACTURED (OR BATTERIES SERVICED OTHER
THAN) BY ANTON/BAUER. SUCH USE WILL VOID ANY
WARRANTY.
1
In general, the CINE VCLX/2 charger will deliver a three stage charge
routine to each battery.
LED INDICATIONS
1. STAGE ONE will deliver a high rate charge matched to the capabilities of the battery. During this stage, six separate cutoff methods are in operation, simultaneously, ensuring the fastest, safest charge for that battery:
TCO - Temperature cutoff which stops the Stage one charge precisely when a temperature indicative of full charge is reached;
The CINE VCLX/2 charger has two sets of LEDs.
The red and green charge status LED’s indicate the charging status of the battery. The following table identifies all of the LED indications and their meaning.
Dt/dT - A microprocessor based algorithm which measures a rise in temperature over a specific time, very accurately indicating full charge.
-ΔV - A method to determine the end of stage one charging by identifying a characteristic “reverse slope” of a cell. Since this characteristic can be disguised by the age, temperature and the number of the cells in a battery, it can never be employed alone;
CCO - This method requires the identification of the particular battery size (capacity) and chemistry, an exclusive Anton/Bauer
Logic Series feature. The charger determines the maximum charge time for the particular battery and uses this information to ensure that overcharge conditions are avoided.
LED INDICATION
Alternating
Red & Green
Steady Red
MEANING
Indicates that the CINE VCLX/2 charger is evaluating the battery and/or communicating with a DIGITAL battery, loading battery parameters and determining the appropriate charge routine. A low voltage
(<11V) battery will cause this indication to continue until the battery reaches safe charging voltage.
FUL - This determination is made when a fully charged battery is returned to a charger within specified parameters of time, temperature, and battery voltage. The battery communicates its fully charged condition and the charger confirms the parameters and immediately indicates a fully charged condition, without additional verification.
Flashing Red
Indicates that the battery is being held by the charger to stabilize an out-of-range temperature condition.
Indicates that the battery is currently under Stage One charge.
TEMPERATURE COMPENSATED VCO – Optimizes VCO cutoff to operate only within certain temperature parameters.
In addition, a voltage limiting constant current Stage One routine address the critical parameters of li ion batteries.
Steady Green Indicates that the battery is
READY and in Stage Two or
Three Lifesaver mode.
2. STAGE TWO charging is a BALANCING or “stabilizing” mode which calculates each battery pack type to offset any imbalance of the battery’s cells, created by unequal self discharge or any capacity mismatch of the individual cells in the pack. This stage can vary in duration from zero to as much as 16 hours, depending on the condition of the battery. A battery will typically leave Stage Two in
2-4 hours under average operating conditions.
3. STAGE THREE charging is the Anton/Bauer exclusive
Lifesaver® maintenance mode. This patented pulse routine keeps batteries fully charged, free from self-discharge indefinitely without damaging heat associated with a so-called “trickle charge”.
Red/Green Charge Status LED
Green Status LED
4. NOTE: Batteries may be kept on a charger until ready for use.
The Lifesaver mode will keep them 100% charged.
2
This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This equipment has been approved by one or more agencies. All changes and/or modifications not expressly approved by Anton Bauer, Inc. could void the users’ warranty and authority to operate this equipment. There are no serviceable parts in this equipment.
SPECIFICATIONS
Size
Weight
Input Voltage
Output Voltage
Rated Power
Fuse Rating
2.25” x 5.75” x 6.25”
2.5lbs. (1.13kg)
100-240VAC 50/60 Hz
24 VDC 10 +/- 10%
85 watts
3 amps, 250V
FUSE/TYPE REPLACEMENT
The fuse of the CINE VCLX/2 charger is a PCB mounted device which should only be replaced by a qualified service technician.
3
This one (1) year limited warranty for the product specified in this document (“Product”) is given by Anton/Bauer, Inc. (“Anton/Bauer”),
14 Progress Drive, Shelton, Connecticut 06484. If you (the purchaser of the Product from Anton/Bauer, or the person for whom the Product was purchased, if it was a gift) have any questions regarding Product applications, Product specification, or to obtain warranty service on this or any Anton/Bauer product, contact the company at the address above.
THIS PRODUCT MUST BE REGISTERED WITH ANTON/BAUER
WITHIN 30 DAYS OF PURCHASE TO ASSURE WARRANTY COVER-
AGE. TO REGISTER YOU MAY EITHER:
(1)
(2)
MAIL WARRANTY REGISTRATION CARD or
REGISTER ON LINE AT www.antonbauer.com
The liability of Anton/Bauer hereunder is expressly limited to a claim for repair or replacement of the Product or as otherwise stated herein at Anton/Bauer’s sole discretion. Notice of any claim under this warranty shall be delivered to Anton/Bauer during the period of the warranty and the Product shall be returned with its packaging promptly, at your expense, to an Anton/Bauer Customer Support Center or to the address above. Upon receipt of the Product and a record of your compliance with the conditions of this warranty, Anton/Bauer will repair or replace the Product and return it to you, or issue a credit, as applicable. You are responsible for all shipping and handling charges to and from authorized facility.
THIS WARRANTY DOES NOT APPLY TO AND IS VOID IN THE CASE
OF DEFECTS OR DAMAGE RESULTING FROM ACCIDENTS, DISAS-
TER, NEGLECT, MISUSE, IMPROPER INSTALLATION, IMPROPER
OR UNAUTHORIZED SERVICE OR MAINTENANCE, UNAUTHORIZED
REPLACEMENT PARTS OR ATTACHMENTS; OR DYSFUNCTION OR
MALFUNCTION OF, OR CAUSED BY, ANY OTHER PRODUCT OR
DEVICE. Misuse includes any use of the Product in other than its intended application, including the use of this Product with any charging device or accessory not manufactured by and/or specified by Anton/Bauer. This warranty does not cover, and Anton/
Bauer assumes no responsibility for, any equipment or devices
used in conjunction with the Product.
ANTON/BAUER DISCLAIMS ANY LIABILITY FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY WRITTEN OR
IMPLIED WARRANTY OF THE PRODUCT. UNDER NO CIRCUM-
STANCES WILL ANTON/BAUER BE RESPONSIBLE FOR ANY SPE-
CIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
This Warranty is to be construed and enforced in accordance with the law of the State of Connecticut, including the provisions of the Uniform Commercial Code as adopted and from time to time amended in the State of Connecticut, and not the Convention for the International Sale of Goods. This choice of Connecticut law is exclusive of any Connecticut law that would require reliance on any law foreign to
Connecticut. Should any action of law or in equity be brought by any person under this Warranty, such action shall be brought only in the
United States District Court for the District of Connecticut, or in any
Superior Court in Fairfield County, Connecticut, USA. Some states do not allow limitations on how long a warranty lasts, so the time period limitation herein may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may have other legal rights which may vary from state to state.
Use of unauthorized equipment in conjunction with Anton/Bauer products constitutes misuse under our warranties and may limit or void those warranties. Anton/Bauer does not authorize, condone, recommend, or otherwise assume any liability or responsibility resulting from the use of any battery, charger, or accessory made by Anton/Bauer with any battery, charger or accessory not manufactured, produced or sold by Anton/Bauer. Anton/Bauer only authorizes the use of original
Anton/Bauer products with this Product. Use only original Anton/
Bauer equipment with this Product.
4
Approved Copy
Anton/Bauer, Inc.
World Headquarters
Fax (203) 929-9935
The following are trademarks of Anton/Bauer, Inc.:
Anton/Bauer, Anton/Bauer logo and parallelogram design, Aspekt, Automatique,
DataTap, DIONIC, Elipz, Egripz, Elightz, Essentialz, Gold Mount, HubZ, HyTRON, Impac,
Interactive and design, LifeSaver, Logic Series, Logic Series Logo, Maxx man logo design,
Nexus, PowerStrap, Proformer, Probe, ProPac, RealTime, Satellight, Snap-On, Stasis, Stasis
Flex, Tandem, TrimPac, Ultrakit, Ultralight, “One World. One Smart Choice”, “The power behind the best cameras capturing the best images in the world.”, “The quality standard of the video industry”, “The worldwide standard”, and “There should always be choices. It makes it easier to recognize the best.”
Lexan is a registered trademark of G.E. Company Corp.
Cordura is a registered trademark of E.I. duPont de Nemours
14 Progress Drive, Shelton, CT U.S.A.
Tel (203) 929-1100 or (800) 541-1667 [email protected]
Anton/Bauer Europe, B.V.
Eurode Business Center, Eurode - Park 1-2
6461KB Kerkrade, The Netherlands
Tel (+31) 45 5639220
Fax (+31) 45 5639222 [email protected]
Anton/Bauer, Inc. - Signapore Office
6 New Industrial Road, # 02-02 Hoe
Huat Ind. Bld., Singapore 536199
Tel (+65) 62975784
Fax (+65) 62825235 [email protected]
www.antonbauer.com
Anton/Bauer
A Vitec Group brand
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project