1 2 Single Channel HD Video Active UTP Receiver User

Single channel HD Video Active UTP
receiver
UTP101AT
Single Channel HD Video Active UTP Receiver
User Manual
Board Diagram
VerB 1.0
7
2
The product adopts Cat 5/5e/6 UTP cable as transmission medium, It can receive color or
mono PAL/NTSC/SECAM video or HDCVI、AHD、HDTVI HD video in real time. It features
long transmission distance, good transmission effect, super anti-interference, wide CCTV
surveillance system.
Application
1
Mo
nit
Mo
or
C
DV
NO.
nit
or
oa
x
R
3
4
5
6
Description
Component
Po
w
er
H
D
Power supply block
Power supply input
2
Green terminal block
Grounding
3
4
Green terminal block
For UTP cable
switches
For color adjustment
5
switches
For brightness adjustment
6
BNC-M
Video Output
7
MIT Pole
For MIT Installation
e
U
iv
ct
A
o r
de ve
Vi ei
g c
lo Re
na P
A UT
1
TP
C
at
5/
5e
/6
H
Installation Steps
D
A
ss
Pa
o
de un
Vi al
g B
lo P
na UT
iv
e
Feature
DC12V~36V/AC 9V~24V;
Real time transfer of PAL、NTSC、SECAM video, HDCVI、AHD、HDTVI HD video;
Recommendation transmission distance as below:
1) HDCVI1080p: 330m; HDCVI 720P: 500m; ( passive to active);
2)HDTVI 720p/1080p: 300m ( passive to active);
3)AHD-L/M 720P/960P: 480m; AHD-H 1080P: 450m(passive to active);
4)Analog video: 650m ( passive to active);
Adopts UTP cable for the transmission, support DIP adjustment;
Wide range voltage AC/DC power input, strong surge protection and anti-interference
Delicate design, support MIT rack.
Please check the following items before installation. If it’s missing, please contact the
dealer
Receiver
1set
User Manual
1set
Please follow the next installation steps:
1) Please power off the camera and monitor before installation;
2) Please connect the camera port and the transmitter's input port (BNC) with coaxial;
3) Please plug the monitor port and the receiver's output port (BNC) with coaxial
4) Please connect the UTP cable with the receiver and transmitter (VIDEO + - port);
5) Please adjust the DIP adjustment according to the instruction;
6) Please examine the system.
Notice
Please use standard UTP cable and coaxial to provide the transmission quality.
1
2
Single channel HD Video Active UTP
receiver
UTP101AT
Single channel HD Video Active UTP receiver
Specification
连接接口
Item
Description
Transmission Channel
1 ch
Output
2ch
Distance
Please refer to table 1
Voltage Range
DC12V~36V or AC 9V~24V
Table 1:
Function
Power
Video
Transmission
DIP
Status
Power Rate
< 1W
Coaxial Port
Female BNC
UTP Cable Port
5pin port
Video System
PAL、NTSC、SECAM video,
HDCVI、AHD、HDTVI HD video .
Signal Bandwidth
0-7 5 MHz
Anti-interference
> 75dB
DIP Switch
Switch
Adjustment mode
Rotate
Power LED
Red
Signal LED
Yellow
Power Port Protection
2KV / 1KA Per:IEC61000 - 4 - 5
Coaxial Port Protection
2KV(different mode) 4KV(common mode)
Per:IEC61000-4-5
Protection
Signal Source
HDCVI
(720P)
Recommendation
500m
distance
HDCVI
(1080P)
HDTVI
(720P/1080P)
AHD-L/M
(720P/960P)
AHD-H
(1080P)
Analog
Video
330m
300m
480m
450m
650m
Instruction:
The test data in table 1 is required under lab environment by passive to passive,In
actual case, there maybe some differences due to different cable and environment.
1a contact discharge Level 2
ESD
1b a ir discharge Level 2
Per: IEC61000-4-2
Environment
Structure
Working Temperature
0℃~ 55℃
Storage Temperature
-40℃~ 85℃
Humidity
0 ~ 95 %
Size
115mm×82mm×22mm
Case
Iron
Color
Silver w hite
N.W.
180g
Specification change will not be noticed.
Problem Examination
连接接口
Please find the following solution when the device doesn't work
Please make sure the installation is according to the instruction;
Please make sure the RJ45 cable plug support 568A or 568B;
Please make sure each UTP cable is according to the related channel;
Please examine the port of BNC,RJ45;
Please make sure the distance exceed the max distance range;
Please make sure the transmission cable is reliable;
Please replace the failure product with a working one;
Please contact your local dealer if the problem still exist.
3
4