TO QT- LED - Underwater Lights Limited

BULLEYT & UL Ti MATE
TO
QT- LED
Just to let you know Underwater Lights Limited have made a
conversion package to change our original
metal halide underwater lights manufactured since 1991
to LED without changing the insert or screwed hull fitting.
The conversion uses our standard cool white LED
which is shown in a recent retro fit.
Picture above shows the light output.
The conversion can also use our
colour changing R.G.B + White LED
This does requires the addition of DMX cabling on board.
The additional documents show the underwater lights that can
be converted to LED.
Please consult us for further information at RETRO@ UNDERWATERLIGHTS.COM
TM
underwater lights limited
TM
Manufacturer of the Original underwater lights
Brand Marine Lighting Products since 1991
QT LED -RETRO
For sales and information visit WWW.QTLED.COM
CONVERSION FROM
CUTE ON SIZE - BIG ON LIGHT
RETRO
75 RETRO
CONVERSION FROM
QT- LED
PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO
WWW.REGISTER-UWL.COM
For sales telephone numbers visit www.qtled.com
THE QT-LED RANGE IS DESIGNED AND MANUFACTURED BY UNDERWATER LIGHTS LTD IN THE U.K.
QT LED -RETRO
For sales and information visit WWW.QTLED.COM
TO
CUTE ON SIZE - BIG ON LIGHT
BULLEYT & UL Ti MATE
Bulleyts 316L Stainless Steel
ORDERING NUMBER FOR 120 VOLT AND 230 VOLT MODELS
A00310-120, A00324-120, A00338-120, A00350-120
A00310-230, A00324-230, A00338-230, A00350-230
OPERATIONAL CONDITIONS AND CONSIDERATIONS
Do not attempt to remove the glass lens while afloat.
The Bulleyt is serviced from inside the hull. Allow access
The projector must be correctly assembled with lid
for maintenance and space for ventilation.
and secured to the Bulleyt whilst afloat.
Do not use the Bulleyt in dry-dock or out of the water.
Allow a minimum of 70mm behind the projector lid
(item 2) for lamp replacements.
ELECTRICAL INFORMATION
Cable specification from electronic ballast to projector (Pt.No. S00111)
Shielded 3 core, Temperature -60C to +180C, Voltage 2000 volts.
Maximum distance between ballast and projector with the shield
earthed 20 meters.
120 volt 150 watt ballast - running current 1.5 amps
230 volt 150 watt ballast - running current 0.75 amps
ELECTRONIC BALLAST COMPLETE
WITH ALUMINIUM ENCLOSURE -S00800-120 OR 230
FLUSH - A00310
0-24 DEGREE - A00324
50 DEGREE - A00350
24-38 DEGREE - A00338
Recommended Spares
Part No
Lamp (150w HQI)
91004
Glass with gaskets
S00C01-2
Electronic ballast-120v S00801-120
Electronic ballast-230v S00801-230
Part Description
Part No
1: Projector cable
S00111
2: Projector lid complete
S00C102
3: "O" Ring
00108
4: Projector case
00101
5: Lamp (150w HQI)
91004
6: Reflector
91791
7: Connecting ring
000C03
8: Gaskets
000C07
9: S.S. M6 socket screws
93306
10: Glass retaining ring
000C04
11: Gaskets
000C02
12: Glass
000C01
13: Electronic ballast-120v S00801-120
13: Electronic ballast-230v S00801-230
LENS FITTING INSTRUCTIONS
Check the glass landing surface is clean and apply a suitable silicone grease to the gaskets. Fit 6
the glass, gaskets and retaining ring as shown above. Hand tighten the screws with a 5mm
“Allen key” making sure the glass retaining ring is square. Torque the screws to 9Nm (7ft/lbs)
in the sequence shown, check the ring again and re-torque the screws again to the same setting. 4
1
3
5
2
PLEASE REGISTER YOUR PRODUCT WARRANTEE DIRECT TO WWW.REGISTER-UWL.COM
FOR TECHNICAL INFORMATION PLEASE EMAIL T@UNDERWATERLIGHTS.COM
SALES, PRODUCT INFORMATION AND NEWS GO TO
WWW.UNDERWATERLIGHTS.COM
BULLEYT
UL Ti MATE 70 316L Stainless Steel
ORDERING NUMBERS FOR 100-277 VOLT 150 WATT LIGHTS
FLUSH - S00310-70A-V1, 20 DEGREE - S00320-70A-V1,
24-38 DEGREE - S00338-70A-V1, 50 DEGREE - S00350-70A-V1
OPERATIONAL CONDITIONS AND CONSIDERATIONS
The UL Ti MATE is serviced from inside the hull. Allow
Do not attempt to remove the glass lens while afloat.
access for maintenance and space for ventilation.
The projector must be correctly assembled with lid
Do not use the UL Ti MATE in dry-dock or out of the water secured to the UL Ti MATE 70 whilst afloat.
Allow a minimum of 70mm behind the projector lid
(item 2) for lamp replacements.
UL Ti MATE to be fitted 250mm below the yachts water
line when loaded with 50% fuel and 50% freshwater onboard.
ELECTRICAL INFORMATION
Cable specification from electronic ballast to projector (Pt.No. S00111)
Shielded 3 core, Temperature -60C to +180C, Voltage 2000 volts.
Maximum distance between ballast and projector with the shield
earthed 10 meters.
Ballast power 100/277 volt 150 watt ballast - running current 2.0/07.A
Ballast will not ignite a hot lamp. The ballast has a cycle
ELECTRONIC BALLAST COMPLETE WITH IP65
of three atempts to ignite the lamp then will wait for four
ENCLOSURE -S00800-V1W2 (V1=100-277 VOLTS, W2=150 WATTS)
minutes before repeating the cycle.
FLUSH - S00310-70A
20 DEGREE - S00320-70A
50 DEGREE - S00350-70A
24-38 DEGREE - S00338-70A
Recommended Spares
Lamp (150w HQI)
Glass with gaskets
Electronic ballast
Part No
91205
S00C01-70A
95322
Part Description
Part No
1: Projector cable
S00111
2: Projector lid complete
S00C102
3: "O" Ring
00108
4: Projector case
00101
5: Lamp (150w HQI)
91205
6: Reflector
91791-1A
7: Connecting ring
000C03
8: Gaskets
000C07
9: S.S. M6 socket screws
93334
10: Glass retaining ring
00304-70A
11: Gaskets
00278-A
12: Glass
00280-70A
13:Electronic ballast-100/277v S00800-V1W2
LENS FITTING INSTRUCTIONS
6
Check the glass landing surface is clean and apply a suitable silicone grease to the gaskets. Fit
the glass, gaskets and retaining ring as shown above. Hand tighten the screws with a 5mm
Allen key making sure the glass retaining ring is square. Torque the screws to 10Nm (7.5ft/lbs)
in the sequence shown, check the ring again and re-torque the screws again to the same setting. 4
1
3
5
2
PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW,REGISTER-UWL.COM
FOR TECHNICAL INFORMATION PLEASE EMAIL T@UNDERWATERLIGHTS.COM
SALES, PRODUCT INFORMATION AND NEWS GO TO
WWW,UNDERWATERLIGHTS.COM
Ul ti mate 70 SS
316 S.S. UL Ti MATE 75 SA-ICE
‘submersible through hull light’
ORDERING NUMBERS
FLUSH - S00300-75-SA-ICE. 30 DEG - S00330-75-SA-ICE. 50 DEG -S00350-75-SA-1CE
WITH 120 (V3) / 230 (V2) VOLT BALLAST AND 150W (W2) OR 250W (V2,W1) WATT LAMP.
UL Ti MATE™ to be fitted a minimumof 250mm below the yachts water
line when loaded with 50% fuel and 50% freshwater onboard
ELECTRICAL INFORMATION
150 WATT Maximum distance between ballast and projector -10 meters
250 WATT Maximum distance between ballast and projector - 10 meters.
Ballast power 150 watt ballast 120/230 volt, running current 1.4/0.7.A
Ballast power 250 watt ballast 230 volt, running current 1.2.A
Ballast will not ignite a hot lamp. The ballast has a cycle of three atempts
to ignite the lamp then will wait for six minutes before repeating the cycle.
Ballast must be installed in dry space. Maximum ambient temperature 40C
DO NOT swich ballast on and off.
TM
OPERATIONAL CONDITIONS AND CONSIDERATIONS
The UL Ti MATE 75 SA is serviced from inside the hull.
Do not attempt to remove the glass lens while afloat.
Allow access for maintenance and space for ventilation.
The projector must be correctly assembled with lid
Do not use the UL Ti MATE™ in dry-dock or out of water
secured to the UL Ti MATE™ whilst afloat.
Allow a minimum of 170mm behind the cable gland for
lamp replacements on 150w and 150mm behind the.ignitor on 250w.
120 & 230 VOLTAGE SUPPLY FOR 150 & 250
WATT ELECTRONIC BALLAST COMPLETE
WITH ENCLOSURE .
CABLE SPECIFICATION TO PROJECTOR
High tempereture (180C) silicone
screened three core. Cable diameter 9mm
PART NUMBER
S00111-180 EWKF 3G0,0.75
Part Description 75-SA
1: Projector lid securing plate
2: M6 Nut
3: 'O' Ring
4: Gasket NAF
5: Connecting ring
6: Lamp holder screw
7: Lamp holder (250W)
7: Lamp holder (150W)
8: Reflector collar bush
9: M4 Lock nut
10: Lamp (250W)
10: Lamp (150W)
11: Reflector adjustment rod
12: Reflector complete
13: Gasket NAF
14: AB2 Connecting ring
15: Projector barrel
16: Gasket NAF
30: Glass gaskets NAF
31: Glass lens
39: Body Flush (s.s)
40: Body 50 deg (s.s.)
41: Body 30 deg (s.s.)
42: Glass retaining ring
43: Cap head screws
Part No
00283-B
93381
00108
00285-A
00274-C
00290
91195
91191
00288-A
93374
91209
91210
00284
S91791
00285-A
00503-75-A
00101-C
000C07-B
00286-A
00281
S00300-75 ICE
S00350-75-B ICE
S00330-75 ICE
S00350-75 ICE (40)
Part Description 75-SA
22: Gland
23: Projector cover
24: Ballast 250 watt 230v
24: Ballast 150 watt 230v
24: Ballast 150 watt 120v
Part No
92011
00102-E
S00820-V2 W1
S00800-V2W2
S00800-V3W2
S00330-75 ICE (41)
FLUSH
150 & 250 watt
Recommended Spares
Lamp ( 250w = W1 )
Lamp ( 150w = W2 )
Glass with gaskets
Ballast
Part No
91209
91210
S00281-A
S00300-75 ICE (39)
00304-ICE 75B
93334
LENS FITTING INSTRUCTIONS
Check the glass landing surface is clean and apply a suitable silicone grease to the gaskets. Fit
the glass, gaskets and retaining ring as shown above. Hand tighten the screws with a 5mm
“Allen key” making sure the glass retaining ring is square. Torque settings for all retaining
screws - 10 Nm (7.5 ft/lbs). Torque the screws in the sequence shown. Check the ring again
and re-torque the screws again to the same torque setting.
PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW,REGISTER-UWL.COM
FOR TECHNICAL INFORMATION PLEASE EMAIL T@UNDERWATERLIGHTS.COM
SALES, PRODUCT INFORMATION AND NEWS GO TO
WWW,UNDERWATERLIGHTS.COM
UL Ti MATE 75-SA-ICE-SS-H-14-10-2011
130 RETRO
CONVERSION FROM
PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO
WWW.REGISTER-UWL.COM
For sales telephone numbers visit www.qtled.com
THE QT-LED RANGE IS DESIGNED AND MANUFACTURED BY UNDERWATER LIGHTS LTD IN THE U.K.
QT LED - 130-RETRO
For sales and information visit WWW.QTLED.COM
TO QT- LED -130
CUTE ON SIZE - BIG ON LIGHT
UL Ti MATE 130
UL Ti MATE 130 Aluminium Bronze
Fixed Screwed Underwater Lights
ORDERING NUMBER FOR 230 VOLT 150WATT LIGHTS S00475-V2(H)W2
ORDERING NUMBER FOR 120 VOLT 150WATT LIGHTS S00475-V3(H)W2
UL Ti MATE 130 INSTALLATION (The UL Ti MATE 130 should be no less than 250mm/10” below the water line)
Qualified/Approved personnel must be used to carry out installation
Cut and prepare a 4 inch / 100 mm clearance hole for the body (16). Coat the flange of the body and the area around the
hole with 3M 4200FC sealant then slide the body into the hole. From the inside fit the compensating ring (17) and screw
the securing ring (18) up “hand tight”. Adjust the screws (19) so the compensating ring is flush to the hull and check the
sealant has flowed completely around the flange. Do “NOT” over tighten the screws as this will squeeze the sealant from
the surface. Allow the sealant to solidify and remove surplus. Finally tighten the adjustment bolts to 4Nm / 3ft.lbs
Note for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface
through it, thus protecting the internal core of the hull.
Maximum hull thickness should not exceed 4.75 inches - 120mm Minimum wall thickness 0.375inches.- 10mm
After completing the installation procedure it is highly recmmended to coat the exposed body with antifouling.
EARTHING LIGHT FOR CATHODIC PROTECTION-tighten the earth screw on the securing ring so that it
bites into the screwed barrel. Check there is continuity to the front face. This prevents galvanic corrosion.
OPERATIONAL CONDITIONS AND CONSIDERATIONS
The UL Ti MATE 130 is serviced from inside the hull. Allow a minimum of 170mm behind the cable gland for lamp
replacements on 150w and 150mm behind the.ignitor on 250w
ELECTRICAL INFORMATION
CABLE SPECIFICATION TO PROJECTOR
150 Watt High temp silicone three core part number. S00111
150 WATT Max distance between ballast and projector with -10 meters
.Ballast power 150 watt ballast 120/230 volt, running current 1.4/0.7.A
Ballast will not ignite a hot lamp. The ballast has three attempts to ignite
the lamp then will wait for four minutes before repeating the cycle.
Do not attempt to remove the glass lens while afloat
ELECTRONIC BALLAST COMPLETE
WITH IP65 ENCLOSURE
Part Description
Part No
1: Cable
S00111
2: Projector lid complete
S00102-C
3: "O" Ring
00108
4: Connecting Ring
00274-B
5: Body
S00475-A
6: Screws (M6X 25 ALU.)
93610
7: Gasket - NAF
00286-A
8: Glass
00281
9: Glass retaining ring
00476-C
10: Comp. ring
00277-B
11: Securing ring
00275-B
13: Electronic ballast-230 volt
95322-V2HW2
13: Electronic ballast-120 volt
95322-V3HW2
12: Reflector Tube with Reflector
S00273
14: Lamp (MSD-150W/70)
91210
15: Gasket - NAF
000C07-A
16: Cable gland
92010
17: Screws (M6X 16 S.S.)
93333
Recommended Spares
Part No
Lamp (MSD-150W/70)
91210
Glass with gaskets
S00279-A
Electronic ballast
95322
EARTH TAB AND SCREW
LENS FITTING INSTRUCTIONS
Check the glass landing surface is clean and apply a suitable silicone grease to the gaskets. Fit
the glass, gaskets and retaining ring as shown above. Hand tighten the screws with a 5mm
Allen key making sure the glass retaining ring is square. Torque the screws to 6 Nm (4.5ft/lbs)
in the sequence shown, check the ring again and re-torque the screws again to the same setting
PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW,REGISTER-UWL.COM
FOR TECHNICAL INFORMATION PLEASE EMAIL T@UNDERWATERLIGHTS.COM
SALES, PRODUCT INFORMATION AND NEWS GO TO
WWW,UNDERWATERLIGHTS.COM
UL Ti MATE 130-FIXED 1-7-2010
UL Ti MATE 130 SA
‘submersible through hull light’
ORDERING NUMBERS
250 WATT LIGHTS - 230V. S00475-SA-V2W1.
150 WATT LIGHTS - 120V. S00475-SA-V3W2. 230V. S00475-SA-V2W2
OPERATIONAL CONDITIONS AND CONSIDERATIONS
The UL Ti MATE 130 is serviced from inside the hull. Allow a minimum of 170mm behind the cable gland for lamp
replacements.
ELECTRICAL INFORMATION
CABLE SPECIFICATION TO PROJECTOR
150 Watt-250 Watt- High temp silicone three core part number. S00111-0.75150 WATT Max distance between ballast and projector with -10 meters.250 WATT Max distance 25 meters
.Ballast power 150 watt ballast 120/230 volt, running current 1.4/0.7.A
Part Description 130-S A
Ballast power 250 watt ballast 230 volt, running current 1.2.A
1: Projector lid securing plate
Ballast will not ignite a hot lamp. The ballast has three attempts to ignite
2: M6 Nut
3: 'O' Ring
the lamp then will wait for four minutes before repeating the cycle.
4: Gasket NAF
Do not attempt to remove the glass lens while afloat
Part No
00283-B
93381
00108
00285-A
5: Connecting ring
00274-C
6: Lamp holder screw
00290
7: Lamp holder (250W)
91195
7: Lamp holder (150W)
91191
8: Reflector collar bush
00288-A
9: M4 Lock nut
93374
10: Lamp (250W)
91209
10: Lamp (150W)
91210
11: Reflector adjustment rod
00284-2-D
12: Reflector complete
S91791
13: Glass retaining ring
00476-B
13A: Cap head screws
93325
14: Glass gaskets NAF
00286-A
16: Body
S00475-A
17: Compensating ring
00277
18: Securing ring
00275
19: Cap head screws
93610
20: Ignitor (250W)
S95325
21: Projector cover (250W)
00102-H
22: Gland
00107
23: Projector cover (150W)
00102-E
24: Ballast 250 watt
S00800-V1W2
24: Ballast 150 watt 230v
S00800-V2W2
24: Ballast 150 watt 120v
S00800V3W2
ELECTRONIC BALLAST COMPLETE
WITH IP65 ENCLOSURE
150 watt
250 watt
EARTH TAB AND SCREW
Recommended Spares
Lamp ( 250w = W1 )
Lamp ( 150w = W2 )
Glass with gaskets
Ballast
LENS FITTING INSTRUCTIONS
Check the glass landing surface is clean and apply a suitable silicone grease to the gaskets.
Fit the glass, gaskets and retaining ring as shown above. Hand tighten the screws with an
Allen key making sure the glass retaining ring is square. Torque the screws to 6 Nm (4.5ft/lbs)
in the sequence shown, check the ring again and re-torque the screws again to the same setting
PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW,REGISTER-UWL.COM
FOR TECHNICAL INFORMATION PLEASE EMAIL T@UNDERWATERLIGHTS.COM
SALES, PRODUCT INFORMATION AND NEWS GO TO
WWW,UNDERWATERLIGHTS.COM
UL Ti MATE 130 SA -20-8-2012
Part No
91209
91210
S00281-A
S00801
TM
UL Ti MATE 130 SA INSTALLATION (The UL Ti MATE 130 SA should be no less than 250mm/10” below the water line)
Qualified/Approved personnel must be used to carry out installation
Cut and prepare a 4 inch / 100 mm clearance hole for the body (16). Coat the flange of the body and the area around the
hole with 3M 4200FC sealant then slide the body into the hole. From the inside fit the compensating ring (17) and screw
the securing ring (18) up “hand tight”. Adjust the screws (19) so the compensating ring is flush to the hull and check the
sealant has flowed completely around the flange. Do “NOT” over tighten the screws as this will squeeze the sealant from
the surface. Allow the sealant to solidify and remove surplus. Finally tighten the adjustment bolts to 4Nm / 3ft.lbs
Note for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface
through it, thus protecting the internal core of the hull.
Maximum hull thickness should not exceed 4.75 inches - 120mm Minimum wall thickness 0.375inches.- 10mm
After completing the installation procedure it is highly recmmended to coat the exposed body with antifouling.
EARTHING LIGHT FOR CATHODIC PROTECTION-tighten the earth screw on the securing ring so that it
bites into the screwed barrel. Check there is continuity to the front face. This prevents galvanic corrosion.