MG245X
XPORT Setting User’s Guide
(VER.1.0)
MG245X-XPORT-001
MG245X XPORT Setting User’s Guide
REVISION HISTORY
Version
Date
VER.1.0
2007.8.31
Description
▪ First Version Release
VER.1.0
Page:2/8
www.radiopulse.co.kr
MG245X-XPORT-001
MG245X XPORT Setting User’s Guide
CONTENTS
1.
INTRODUCTION ............................................................................................................................. 4
2.
SET IP ADDRESS ........................................................................................................................... 4
3.
CONFIGURE XPORT ................................................................................................................... 5
3.1. WEB CONFIGURATION ................................................................................................................. 5
3.1.1.
Connection Setting (Ethernet Port setting) .................................................................. 6
3.1.2.
Serial Settings.................................................................................................................. 6
VER.1.0
Page:3/8
www.radiopulse.co.kr
MG245X-XPORT-001
MG245X XPORT Setting User’s Guide
1. INTRODUCTION
RadioPulse uses XPORT to support Ethernet (TCP/IP) communication method. In addition, Device
Installer program is used to set up Ethernet or Serial environment for XPORT.
For more detailed information, please refer to the online user manual
(http://www.lantronix.com/support/webhelp/device-installer/DeviceInstaller.htm) for Device Installer.
2. SET IP ADDRESS
The following describes the procedure for setting IP Address.
①
Connect XPORT to PC or to desired Ethernet network by a LAN cable.
②
Open Device Installer.
③
When searching XPORT, which is acted in Ethernet, by clicking Search(
enabled XPORT is displayed as shown in [Figure 1] below.
) button, the list of
Search XPORT
connected to network.
Assign IP Address of
XPORT.
Hardware Address of
XPORT selected.
Figure 1. GUI of Device Installer
④
⑤
Click Assign IP(
) button to set IP Address of XPORT.
To set IP Address, type the hardware Address of desired XPORT of XPORT searched in step
③ above. After that, click Next button.
As shown in right side in [Figure1], you can check the hardware address. As well, there is a
label of the hardware address on XPORT. Please refer to it.
VER.1.0
Page:4/8
www.radiopulse.co.kr
MG245X-XPORT-001
MG245X XPORT Setting User’s Guide
⑥
Click ‘Assign a specific IP Address radio button’ below and then click Next button.
⑦
Type desired IP Address and then click the Next button.
⑧ Click Assign (
) button to assign IP Address.
3. CONFIGURE XPORT
There are Web Configuration and Telnet Configuration in XPORT configuration. This section
describes Web Configuration.
3.1. Web Configuration
To execute Web Configuration on Device Installer, please follow step ①~③ in [Figure 2]. You will
see the web page for configuration of XPORT.
②
Click Web
Configuration tab.
③
①
Click IP Address of
XPORT to be
configured.
Check corresponding IP Address
and click GO button
Figure 2. Web Configuration on Device Installer
VER.1.0
Page:5/8
www.radiopulse.co.kr
MG245X-XPORT-001
MG245X XPORT Setting User’s Guide
In addition, Web Configuration can be performed on the general web browser by typing
corresponding address.
3.1.1.
Connection Setting (Ethernet Port setting)
This section describes the connection setting. Please follow the step below after executing Web
Configuration on Device Installer or Web Browser.
①Click the Connection in the left menu.
②Type the desired Port number in the Local Port of Endpoint Configuration section on
Connection Settings window(Default Value is 10001).
③Click OK (
)button on the bottom of Connection Settings window.
④Finally, apply port setting by clicking Apply Settings in the left menu.
3.1.2.
Serial Settings
This section describes the Serial setting. Please follow the step below after executing Web
Configuration on Device Installer or Web Browser.
①Click the Serial Settings in the left menu.
VER.1.0
Page:6/8
www.radiopulse.co.kr
MG245X-XPORT-001
MG245X XPORT Setting User’s Guide
② Please set the parameters(Flow Control, Baud Rate, Data Bits, Parity and Stop Bits) in Port
Settings section based on the module which is connected by XPORT.
③Click OK (
)button on the bottom of Connection Settings window.
④ Finally, apply serial setting by clicking Apply Settings in the left menu.
VER.1.0
Page:7/8
www.radiopulse.co.kr
MG245X-XPORT-001
MG245X XPORT Setting User’s Guide
RadioPulse Inc
3rd Fl., Hans B/D II, 111-6 Seongnae-Dong,
Gangdong-Gu, Seoul, Korea, 134-883, Korea
URL: www.radiopulse.co.kr
Tel: +82-2-478-2963~5
Fax: +82-2-478-2967
sales@radiopulse.co.kr
About RadioPulse Inc.
RadioPulse is a Being Wireless solution provider offering wireless communication & network
technologies and developing next generation wireless networking technologies.
The new wireless networking solutions envisioned by RadioPulse will enable user to enjoy wireless
technologies with easy interface.
Founded in April of 2003, the company maintains it headquarters and R&D center in Seoul, Korea.
Copyright (c) 2009 RadioPulse. All rights reserved.
VER.1.0
Page:8/8
www.radiopulse.co.kr