Digital Output Module DOM4-8

Digital Output Module DOM4-8
Part-No. 583361.22
•
•
•
•
•
•
•
•
•
•
•
•
Compliant with EN 60849 and EN 50849
VdS approval: G 210122
EN 54-16 certified
16 audio slots giving a total of 1 hour memory
4 independent amplifier channels suitable for use with
spurs, zones or loop technology. Built in parametric
equalizer, compressor limiter and delay function (upto
9.9 seconds)
All functions of an alarm and evacuation system
Network into a large system via Ethernet connection
Offers full monitoring of the system functions
Automatic and dynamic switching to redundant
emergency amplifiers
Automatic volume control (AVC) even during
announcements
Remote monitoring and configuration via the network
24 V DC emergency power supply
The control unit DOM4-8 is equipped with 4 independent amplifier channels in
order to operate 8 loudspeaker areas or 4 loudspeaker circuits in VARIODYN D1
loop technology. There is also the option of mixing loop and spur technology with
a DOM.
Rated voltage
Rated frequency
Power consumption
Contact load relay
Ambient temperature
Air humidity
Weight
90 .. 264 V AC
47 ... 63 Hz
40 / 70 W
100 V DC/1 A
-5 °C ... 55 °C
15 ... 90 % (non-condensing)
approx. 5.7 kg
The newest DOM4-8 hardware is not compatible with the DOM firmware 2.6 up to 2.10. For projects requiring
extension or to replace a DOM4-8 featuring DOM firmware 2.6 up to 2.10, it is necessary to order instead
583361.22.UL. This DOM4-8 is fully compatible with firmware version 2.6 up to 2.10 and complies with the
EN54-16.
Accessories:
583451.21 Cable for cabinet rear panel DOM4-8
583486 Patch cable CAT5, 1 m yellow (Ethernet)
583487 Patch cable CAT5, 2 m yellow (Ethernet)
583488 Patch cable CAT5, 3 m yellow (Ethernet)
583496 End-of-line module (EOL)
581316 Microphone, for AVC
583703 Mounting set 1
583342 Loop Isolator Module
583708.HO Ventilation panel 1 HU with Honeywell logo
Novar GmbH a Honeywell Company
Dieselstr. 2 41469 Neuss
Phone: +49 2131 40615 600
Faximile: +49 2131 40615 606
www.ackermann-clino.com
info@ackermann-clino.com
Subject to change without notice!
Features:
The DOM (Digital Output Module) is the central control element of VARIODYN
D1. It has interfaces to all input/output assemblies, administers, and monitors the
loudspeaker circuits for voice alarm systems and electro-acoustic emergency
warning system per EN 60849 and EN 50849. Large or complex system
configurations can be implemented through the networking of multiple DOMs via
Ethernet. The DOM offers a high level of automatic and constant monitoring as
standard. All connected power amplifiers are permanently monitored by the DOM
and if.a power amplifier becomes faulty, it can be replaced dynamically by a
backup amplifier or a backup amplifier channel. The switchover is done
automatically by the DOM. The loudspeaker lines are permanently monitored for
short circuit, ground fault, and failure as well as impedance deviation. Faulty
loudspeaker zones are separated in a non-reacting manner. A DOM contains
storage capacity for preset announcements, which can be used for alarm texts
and signals (escape alarm, caution signal) and warning signals (gongs). The
volume of each source and each amplifier channel can be controlled. Additional
filters like parametric equalizer, high-and low pass filter are available. All errors
are recognized, displayed and recorded within few seconds meeting the
standards. For special applications such as e.g. tunnel, a delay in all four
channels can be programmed up to 9.9 sec.
With the new Firmware it is now possible to connect up to 400 units and get
advantage of the new logical functions which makes it much easier and efficient
to configure the DOM.
© Honeywell International Inc.
Approval: G 210122
Part of EN 54-16 approval