for training purposes only dated material

N
LY
O
S
SE
O
FO
D R
AT T
ED RA
M INI
AT NG
ER P
IA UR
L P
Aperio® Hub
AH40
Installation Instructions
ASSA ABLOY, the global leader
in door opening solutions
1
AH40 - Table of Contents
3
N
LY
AH40 - FCC and Industry Canada Statements
AH40 - Placement of Communication Hub
4
O
AH40 - Connectors5
S
AH40 - Jumpers
7
AH40 - Technical Data 8
FO
D R
AT T
ED RA
M INI
AT NG
ER P
IA UR
L P
O
SE
AH40 - Communication Hub LED Indications
ETL marking
Recognized component
4002570
Conforms to ANSI/UL standard 294, ANSI/UL 60950-1
Certified to CAN/CSA standard C22.2 No. 60950-1
For more detailed information about the Aperio system please read
ST-001279-Aperio Technology Installation Guide AH40.
2
6
7
8
N
LY
O
S
6
SE
5
O
4
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FO
D R
AT T
ED RA
M INI
AT NG
ER P
IA UR
L P
3
AH40 - FCC and Industry Canada Statements
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry
Canada. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that
may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
1. l’appareil ne doit pas produire de brouillage, et
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
The term “IC:” before the equipment certification number only signifies that the
Industry Canada technical specifications were met.
Le terme “IC” devant le numéro de certification signifie seulement que les
spécifications techniques Industrie Canada ont été respectées.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
IEEE 802.15.4 operation of this product in U.S.A. and Canada is limited to
channels 11-25 by Aperio® Programming Application. Outside of U.S.A. and
Canada another version of the Aperio programming application allow use of
channels 11-26.
3
/~
80
ft
FO
D R
AT T
ED RA
M INI
AT NG
ER P
IA UR
L P
5m
O
<2
SE
S
O
N
LY
AH40 - Placement of Communication Hub
Placement of the Hub, 1-8 doors
Note: AH40 must be installed into a junction box ex European
2-Gang, Aperio bottom cover or with Americas adaptor plate to
junction box. AH40 must be installed by qualified and trained
personal. Indoor installation only!
4
EXT INT
O
ANTENNA
N
LY
AH40 - Connectors
J321
FO
D R
AT T
ED RA
M INI
AT NG
ER P
IA UR
L P
- +
8-24V
SE
PAIR
O
LINK
S
J201
Connectors
Description
J201
Ethernet connector. Connection to the Electronic Access
Control system through a 10BASE-T / 100BASE-TX Local
Area Network. Can also be used for power supply if
connected to a IEEE 802.3af compliant Power Sourcing
Device (PSE). Wire requirements CAT5 or higher.
J321
Power supply input, 8-24 VDC, 3.5 W. The power supply
shall be a Limited Power Source (LPS) according to EN
60950-1. The power supply shall be 3 A over current
protected. Wire requirements 16-22 AWG.
Note: When PoE (Power over Ethernet) is used, no power supply
should be connected to J321. The installation must comply with
national wiring regulations.
5
EXT INT
O
ANTENNA
N
LY
AH40 - Jumpers
J321
FO
D R
AT T
ED RA
M INI
AT NG
ER P
IA UR
L P
- +
8-24V
SE
PAIR
O
LINK
S
J201
Jumpers
Description
ANTENNA
Select external antenna by connecting the two left pins.
Select internal antenna by connecting the two right pins.
PAIR
Select pairing mode by connecting the two left pins.
Note: To install an external antenna use a thin screw driver and
gently bend the antenna cap loose. Be careful, there are sensitive
components behind the cap!
6
AH40 - Communication Hub LED Indications
Green
O
Online
N
LY
The Communication Hub has a status LED visible through the front
cover. It supports optical schemes with red, green and yellow. The
indication schemes are described by the figure below:
Aperio Lock
Offline
Green + One
Red Flash
EAC Offline
Green + Two
Red Flashes
SE
S
®
O
Aperio® Lock and
EAC Offline
FO
D R
AT T
ED RA
M INI
AT NG
ER P
IA UR
L P
UHF
Communication
Pairing Active
Green + Three
Red Flashes
Yellow + Off,
Fast Flash
Yellow
Note: With the software tool Aperio® Programming Application
and an USB radio dongle, further system installation parameters
can be set.
ANTENNA
J201
LINK
EXT INT
The “LINK” LED on the
communication Hub
indicates both status of the
Ethernet Link level and if
communication is ongoing.
Note: LED on the Ethernet
connector is not used.
PAIR
J321
- +
8-24V
7
AH40 - Technical Data
82 mm x 82 mm x 37 mm (H x W x T)
Power Supply
8-24 VDC or Power over Ethernet (PoE)
Power Rating
Power supply
The power supply shall be able to deliver minimum
3.5 W. The power supply shall be 3 A over current
protected.
PoE
IEEE 802.3af compliant class 1 Powered device (PD)
Ethernet
10BASE-T / 100BASE-TX Local Area Network
Radio Standard
IEEE 802.15.4 (2400 – 2483,5 MHz)
16 channels (11-26)
15 channels in USA and Canada (11-25)
AES 128 bit encryption
FO
D R
AT T
ED RA
M INI
AT NG
ER P
IA UR
L P
O
SE
S
O
N
LY
Physical Dimensions
Receiver Sensitivity
-100 dBm
Wireless Transmit
Power
10 dBm/MHz according to EN ETSI 300 328.
Maximum spectral density.
Wireless Operating
Range
Indoors up to 25 m depending upon installed
environment.
Internal Antenna
Two port cross polarized patch antenna.
External Antenna
8
One reverse polarity SMA external antenna
connector. AH40 is certified to be used with ASSA
ABLOY external antenna AH ANTENNA 1. If other
external antenna is used it must be of same type
(dipole) and not have larger antenna gain than
3,9 dBi.
Operating
Temperature
5 °C to 35 °C
Humidity
< 95 % non-condensing
IP Classification
IP20
Safety and
Emissions
FCC 47CFR Part 15 subpart B and subpart C
IC RSS-210
EN ETSI 301 489-17 v2.2.1
EN ETSI 300 328 v1.8.1
EN 60950-1 2006 / A11:2009 / A12:2011 / A1:2010
/ AC:2011
UL 294-2010
FO
D R
AT T
ED RA
M INI
AT NG
ER P
IA UR
L P
S
SE
O
N
LY
O
NOTE
9
FO
D R
AT T
ED RA
M INI
AT NG
ER P
IA UR
L P
S
SE
O
N
LY
O
NOTE
10
FO
D R
AT T
ED RA
M INI
AT NG
ER P
IA UR
L P
S
SE
O
N
LY
O
NOTE
11
www.assaabloy.com/aperio
12
M3035.1302
ST-001566-B-EN
FO
D R
AT T
ED RA
M INI
AT NG
ER P
IA UR
L P
O
SE
S
O
N
LY
ASSA ABLOY, the global leader
in door opening solutions
Download PDF
Similar pages