HP-1000 - Time Clock Supplies

HP-1000
Terminal User’s Guide

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy, and, if not installed and used in accordance with the Installation Manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference, in which case the user will be required to correct the interference at the user’s own expense.
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numerique de la classe A respecte toutes les exigences du Reglemente sure le materiel brouilleur du
Canada.
© 1998 through 2011 Schlage Biometrics, Inc. – ALL RIGHTS RESERVED
Document Part Number: 70100-6009 – Revision 3.3 – July, 2011
HandPunch is a trademark of Schlage Biometrics, Inc.
The trademarks used in this Manual are the property of the trademark holders. The use of these trademarks in
this Manual should not be regarded as infringing upon or affecting the validity of any of these trademarks.
Schlage Biometrics, Inc. reserves the right to change, without notice, product offerings or specifications.
No part of this publication may be reproduced in any form without the express written permission from Schlage
Biometrics, Inc.
Table of Contents
Introduction
3
Biometrics
Principle of Operation
Specifications
3
4
6
Planning an Installation
8
Site Preparation
HandPunch Placement
Wiring
Power Input
Battery Backup Operation
HandPunch to Host Computer Connection
RS-232 Host Computer Connection
Modem Host Computer Connection
8
8
9
9
9
10
10
11
Mechanical Installation
12
Wall Plate Installation
12
Wiring Connections
16
Erasing the Memory
19
Erasing HandPunch Memory
19
Closing the HandPunch
20
Enter Command Menu
21
If No One is Enrolled in the HandPunch
If Users are Enrolled in the HandPunch
Navigating Command Menus
21
21
23
Programming the HandPunch
24
System Management
Service Menu
Setup Menu
Management Menu
Enrollment Meunu
Special Menu
26
27
29
32
34
38
HandPunch Maintenance
39
Appendix A - Installation Tips
41
Appendix B - Differences in Board Layout
42
Appendix C - Old Board Configuration
43
Appendix D - Troubleshooting
54
Glossary
56
Limited Warranty
57
Introduction
The HandPunch 1000 is a member of the Schlage Biometrics’ line of biometric hand
geometry Time and Attendance Terminals1. The HandPunch records and stores the threedimensional shape of the human hand for comparison and identity verification. Upon
verification, the HandPunch records the time, date, user ID number, and collected time
and attendance data for collection by a host computer. The HandPunch can communicate
with a host computer.
The HandPunch provides proof-positive employee identification combined with the
sophisticated operating features one expects in a modern Time and Attendance Terminal.
Because of this unique combination of capabilities, the HandPunch provides the most
accurate Time and Attendance data collection terminal available. The key features of the
HandPunch include:
• Transaction Buffer
-- 5,120 event capacity
• Programmable Clock and Date Formats and Daylight Savings Switch-over
Biometrics
Biometrics is a term describing the automatic measurement and comparison of human
characteristics. While its origins are ancient, the evolution of advanced scanning and
microprocessor technology brought biometrics into everyday life. Electronic hand
geometry technology first appeared in the 1970s. Schlage Biometrics Inc., founded
in 1986, built the first mass-produced hand geometry readers and made biometric
technology affordable for the commercial market. Today, Schlage Biometrics’ products are
in use in every imaginable application from protecting cash vaults to verifying employee
attendance in hospitals.
1 For the sake of using a consistent name throughout the manual, the HandPunch 1000 terminal
is referred to as the HandPunch for the remainder of this manual.
Introduction
Principle of
Operation
The HandPunch uses low-level infrared light, optics, and a CMOS (IC chip) camera
to capture a three-dimensional image of the hand. Using advanced microprocessor
technology, the HandPunch converts the image to an electronic template. It stores the
template in a database with the user’s ID number.
To gain punch, the user enters his or her ID number at the HandPunch’s keypad or uses
an external card reader. The HandPunch prompts the user to place his or her hand on
the HandPunch’s platen2. The HandPunch compares the hand on the platen with the
user’s unique template. If the images match, the HandPunch records the transaction for
processing.
The
HandPunch
Terminal
The HandPunch is a time and attendance terminal designed for use with time and
attendance software. Refer to Figure 1-1 on page 5 when reviewing the information in this
section.
The HandPunch has an integrated keypad for ID entry (see “Figure 1-1”). The CLEAR and ENTER keys are used
for data entry and programming.
Four different features assist the user with hand placement and read verification.
1. A light emitting diode (LED) hand placement display on the HandPunch’s top panel
assists users with hand placement on the platen.
2. A liquid crystal display (LCD) shows operational data and programming menus.
3. “Red light/Green light” verification LEDs quickly inform users if their verification
attempts were rejected or accepted.
4. An internal beeper provides audible feedback during keypad data entry and user
verification.
2 The Platen is the flat surface at the base of the HandPunch (see Figure 1-1). This is where
users place their hands for enrollment and verification. It has guide pins to assist positioning
the fingers during use.
4
HandPunch 1000 Manual
HAND
PLACEMENT
DISPLAY
VERIFICATION
LIGHTS
LCD DISPLAY
Recog
nition
NUMERICAL
KEYPAD
1
4
7
*
No
8
0
2
3
5
6
System
s Inc.
Clea
r
9
#
Nos
Ye
Ente
r
PLATEN AND GUIDE PINS
Figure 1-1: The HandPunch 1000
5
Introduction
Specifications
Table 1: Specifications
6
Size:
8.85 inches wide by 11.65 inches high by 8.55 inches deep
22.3 cm wide by 29.6 cm high by 21.7 cm deep
Power:
12 to 24 VDC or 12 to 24 VAC 50-60 Hz, 7 watts
Weight:
6 lbs (2.7 kg) – 7 lbs (3.2 kg) with optional backup battery
Temperature:
-10°C to +60°C – non-operating/storage (14°F to 140°F)
5°C to 40°C – operating (40°F to 110°F)
Relative Humidity
Non-Condensing:
5% to 95% – non-operating/storage (non-condensing)
20% to 80% – operating
Verification Time:
1 second or less
Memory Retention:
5 years using a standard internal lithium battery
Transaction Buffer:
5,120 transactions
ID Number Length:
1 to 10 digits
Baud Rate:
300 to 28.8 K bps
Communications:
RS-232, optional Modem
User Capacity:
HP­1000 50 ­ 512 users
HP­1000­E 100 users only
HandPunch 1000 Manual
Options
The HandPunch has the following options available.
• Backup Battery Support
• Modem Communication
UL Compliance
See Technical Note 70200-0012 rev C
See Technical Note 70200-0013 rev C
Hand Readers are UL Listed as stand alone units only (i.e. the card reader function
has not been evaluated by UL).
The HandKey ll has not been tested for UL 294 in an Outdoor configuration.
approved
recyclable
7
Planning an Installation
Site
Preparation
Before you begin installation, check the site blueprints, riser diagrams, and specifications
for important information about HandPunch location and for other systems that connect to
the HandPunch. Look for any existing wall preparations and wiring that other contractors
may have installed for the HandPunch. A wire routing layout diagram (see Figure 3-2 on
page 14) is provided to assist in planning wire routing.
HandPunch
Placement
The recommended height for the HandPunch platen is 40 inches (102 cm) from the
finished floor. The HandPunch should be out of the path of pedestrian and vehicular
traffic, and convenient to the door it is controlling. Avoid placing the HandPunch where
users must cross the swing path of the door. The HandPunch should be in an area where
it is not exposed to excessive airborne dust, direct sunlight, water, or chemicals.
40 in. (102 cm.)
Figure 2-1: HandPunch Placement Rules
NOTE For the following sections, Schlage Biometrics does not supply hardware items such as
power or communications wiring.
HandPunch 1000 Manual
Wiring
Two basic circuits typically connect to the HandPunch:
• Power Input
• HandPunch to Host Computer
-- RS-232
-- modem
The minimum wire size for these circuits is AWG 22; the maximum is AWG 18.
Power Input
The HandPunch uses an internal switching regulator to obtain internal operational
power. It accepts input voltages from 12 to 24 VDC or 12 to 24 VAC at 50 to 60 Hz.
The HandPunch comes with a 120 VAC to 13.5 VDC power supply (Class 2, Model No.
P48131000A010G – 120 VAC, 60 Hz, 21 W, 13.5 VDC output @ 1000mA). An optional
220 VAC to 13.5 VDC power supply is also available.
To power the HandPunch with this power supply, a 120 VAC (or 220 VAC as applicable)
duplex outlet must be within 5 feet of the HandPunch. The power supply has a 6-foot
cable to provide a comfortable reach between power outlet and HandPunch. The barrel
jack at the end of the power supply’s cable is connected to J12 on the HandPunch PCB.
NOTE Do not connect a HandPunch’s power supply to a switched duplex outlet. The
HandPunch must have a constant source of power for proper operation.
Battery Backup
Operation
An optional power-fail protection circuit board can be attached to the main circuit board
to provide and control battery backup. The battery backup option uses a 12 volt 800 ma/
hour sealed lead acid battery to provide backup battery power. This battery is located
immediately inside the rear panel of the HandPunch and plugs into jack J4 on the keypad
control circuit board located in the top of the chassis.
The design of the HandPunch’s internal power supply is such that any range of the
above input voltages may be used and still provide proper battery charge voltage and
battery backup operation. Switch-over to battery power is automatic and occurs when the
input voltage falls to approximately 10.5 volts. At that time the backup battery charger is
disabled to save power, and uninterrupted operation continues on battery power.
When input power is restored, the HandPunch switches off of battery operation and the
battery charger is re-enabled to recharge the battery. Battery charge voltage is set at
approximately 13.65 volts, and battery charge current is limited to approximately 50 mA.
A fully discharged battery requires approximately 12 hours of charge to fully recover.
9
Planning an Installation
Additional options installed and specific configurations within the HandPunch make it
difficult to predict precisely how long battery support will last, but in general two hours
of battery operation can be expected. While operating on battery backup due to loss of
main input power, the battery output voltage is constantly monitored by internal circuitry.
If the battery voltage reaches approximately 9.5 volts the HandPunch automatically shuts
down. This is done to prevent full exhaustion of the battery. A yellow indicator on the
top panel illuminates to indicate that the HandPunch is running on battery power. This
indicator turns off when main input power is restored.
Shunt J7, which is located immediately in front of the DIP switches on the main logic
board (see Figure 4-1 on page 16), enables or disables battery operation on those
HandPunches equipped with optional battery backup. If a HandPunch does not have the
optional battery backup package installed, J7 is not used. On HandPunches equipped
with the battery backup option, J7 allows service personnel a mechanism for disabling
battery backup operation before removal of main input power.
To fully power down a HandPunch equipped with battery backup, remove or reposition
shunt J7 so that the two pins protruding up from the main logic board are not connected
to each other. This effectively opens the circuit, removing the battery from any internal
circuitry. Main input power can then be removed and the HandPunch will fully shut down.
Once the HandPunch has fully shut down, shunt J7 may be reinstalled.
The design of the power supply is such that main input power must be reapplied to reenable the battery protection mechanism. If shunt J7 is not properly installed, the internal
backup battery will not be charged, and in the event of a main input power loss, the
HandPunch will shut down.
HandPunch to
Host Computer
Connection
HandPunch/host computer communications can be configured in one of two ways:
RS-232 Host
Computer
Connection
A direct HandPunch connection to a host computer can be made through an 4- conductor
cable in an RS-232 serial configuration. A 6’ or 50’ cable may be purchased through RSI
or a wiring diagram for the RS-232 to host computer connection is found on Table 2 on
page 17.
10
• via a direct RS-232 connection
• via an optional Modem connection
HandPunch 1000 Manual
Modem Host
Computer
Connection
The HandPunch is also available with an optional modem module for telephone line
communications between the HandPunch network and the host computer. When
connecting via modem, one HandPunch terminal must be configured with the modem
option. This terminal will communicate with the host computer.
To make the modem connection, a telephone jack must be installed on or in the wall
behind the modem HandPunch terminal. Position the RJ-11 jack location using the
template provided in this manual (see Figure 3-2 on page 14). The short black cable
provided with the modem HandPunch connects the terminal to the telephone jack. Figure
4-4 on page 18 a wiring diagram for a modem to host computer connection.
11
Mechanical Installation
Select an installation location based on the guidelines provided in the Planning an
Installation section beginning on page 8.
Wall Plate Installation
Wall Preparation
NOTE For the following procedure protect the HandPunch from the dust and debris generated
during the wall plate installation process.
1. Remove the wall plate from the packing carton. Refer to Figure 3-1 for all wall plate
references in the following section.
HOLE
2 UPPER SCREWS
SURFACE
CONDUIT
ENTRY
Figure 3-1: Wall Plate
2. Measure and mark a point 48 1/2 inches (123 cm) from the surface of the finished
floor. This point will correspond to the Leveling Hole where the top-center point of the
HandPunch should be mounted.
3. For a hollow wall, drive a small nail into the wall at the mark and hang the wall plate
from the Leveling Hole located near the top of the wall plate.
4. For a solid wall, hold the wall plate against the wall, centering the Leveling Hole over
the mark in the wall.
HandPunch 1000 Manual
5. Align a bubble level with the top edge of the wall plate and gently rotate the wall plate
until the bubble level shows that the top edge of the wall plate is level.
6. Secure the plate to the wall using heavy masking tape.
7. Using the wall plate as a template, mark the locations of the two upper screw holes
and the three lower screw holes.
8. For a concealed wiring connection, trace the outline of the open area in the center
of the wall plate. Identify and mark a 1/2 inch hole through which the HandPunch’s
wiring will be mounted.
9. For a surface conduit wiring connection, mark the two conduit clamp holes at the right
side of the wall plate.
10. Remove the wall plate, masking tape, and the nail (if used).
Mounting the
Wall Plate
1. For a hollow wall, use the provided hardware to mount the wall plate. Use the two
auger style fasteners for the upper two mounting holes. Use the toggle bolts for the
three lower mounting holes.
2. For a solid wall, use expansion bolts to mount the wall plate. For all five mounting
holes, drill a 1/4 inch diameter hole, 1/4 of an inch deeper than the length of the
expansion anchor.
Routing the
Wire
1. Refer to Figure 3-2 on page 14 for a template diagram to assist in routing wiring.
2. For a concealed wiring connection, drill a 1/2 inch hole in a convenient location within
the open area of the wall plate. Pull the wiring to enter the HandPunch through this
hole in the open area.
3. For a surface conduit wiring connection, drill a 1/4 inch diameter hole, 1/4 of an inch
deeper than the length of the expansion anchor for each of the two conduit clamp
holes. Route 1/2 inch, flexible conduit to the HandPunch, ending the conduit between
the two conduit clamp holes. Pull the wiring to enter the HandPunch through the
conduit. Pull 18 inches of wire past the end of the conduit to allow enough space for
final connection to the HandPunch.
4. Clear all dust and debris away from the HandPunch mounting location.
13
Mechanical Installation
Wall Plate
SURFACE
CONDUIT
ENTRY POINT
CL
50" Reference
(127 cm)
to Top of
Wall Plate
42.75"
(108.6 cm)
CL
HandPunch
42.5"
(108 cm)
Finished Floor
Figure 3-2: HandPunch Wire Routing Layout
NOTE Dust and debris surrounding the HandPunch can drastically affect the terminal’s
operation. It is important to ensure the HandPunch mounting location is free from dust
and debris.
Attaching the
HandPunch
14
1. Remove the HandPunch from its carton.
2. Align the sleeves of the back plate with the pins of the wall plate and slide the
HandPunch to the left as shown in “Figure 3-3”.
HandPunch 1000 Manual
HOLE
2 UPPER SCREWS
SURFACE
CONDUIT
ENTRY
REAR OF TERMINAL
Figure 3-3: Attaching the HandPunch to the Wall Plate
15
Wiring Connections
Once the HandPunch is attached to the wall plate the wiring connections to the
HandPunch can be made (see Figure 4-1).
WALL
Power
Connectors
Reset
Switch
J7 Battery
Jumper
Wall Plate
Optional Modem Serial RS-232
Top of
Terminal
Top of HandPunch
Figure 4-1: Board Layout
Wiring
Examples
Table 2 on page 17 provides the pinouts for the RS-232 Serial Host Computer Connection.
Figure 4-2 on page 17 provides a diagram of the RS-232 Connector.
Figure 4-3 on page 18 provides a Serial Connection diagram
Figure 4-4 on page 18 provides a Host PC to HandPunch Modem Network wiring diagram
(Modem wiring is a HandPunch option).
HandPunch 1000 Manual
Table 2: RS-232 Serial Connection
J8 Pin
Signal
Connection
1
GND
Ground
2
RXD
Receive Data Input (from external device)
3
TXD
Transmit Data Output (to external device)
4
RTS
Ready to Send Output (to external device)
RS-232 Pins
1
2
3
4
Figure 4-2: J4 - RS-232 Jack Pinout
17
Wiring Connections
Recogn
ition
1
4
7
*
No
2
3
5
8
0
9
System
s Inc.
Serial Cable
Connection
to Host
Computer
Clea
r
6
F1
F2
#
No
Yes
HandPunch
Serial Port
Ente
r
RS-232 Serial Unit
Host Computer
Figure 4-3: Host PC to RS-232 Connection
Recog
nition
1
4
7
*
No
2
3
5
8
0
s Inc.
Clea
HandPunch
RJ-11
Modem Port
RSI Supplied Cable (Black)
RJ-11
Jack
r
6
9
F1
F2
#
No
Yes
System
Ente
r
Modem Unit
Figure 4-4: Host PC to HandPunch Modem Connection
18
RJ-11 Telephone Outlet
Erasing the Memory
There are two options when erasing the memory of the HandPunch.
1. Setup
2. All
The erasing of the setup will set the HandPunch’s address, passwords, etc. back to
factory defaults.
Choosing the All option will take the HandPunch’s setup back to factory defaults plus
erase all user databases and datalogs. This action can not be undone. If there is a
software that is managing the system then the users can be downloaded back to the
HandPunch if needed.
Erasing
HandPunch
Memory
The erase memory function allows a HandPunch’s setup and/or user database to be
erased.
Perform the following steps to erase the setup programs but retain the user database.
1. With system power OFF, depress reset switch.
2. Turn system power ON and wait 5 seconds.
3. LCD screen will display
ERASE
:1 SETUP
:9 ALL!!!
Closing the HandPunch
Before closing the HandPunch clear all dust and debris away from the HandPunch. With
the wall mount latch in the unlocked position, swing the body of the HandPunch up and
lock the latch into place with the key provided with the HandPunch (see Figure 6-1).
NOTE Dust and debris surrounding the HandPunch can drastically affect the terminal’s
operation. It is important to ensure the HandPunch is free from dust and debris before
closing the terminal.
NOTE Do not force the HandPunch onto the wall mount latch when the latch is in the locked
position.
Wa l l P l a t e
etsyS
m
.cnI s
goceR
noitin
Latch
Key
oN
LOCK
Unlocked Position
Wa l l P l a t e
Latch
Key
Locked Position
Figure 6-1: Closing the Handpunch
Enter Command Menu
If No One is
Enrolled in the
HandPunch
Press the CLEAR and ENTER keys simultaneously to enter a command menu.
1. The display appears as follows.
ENTER PASSWORD
2. Press the default password for the menu you wish to enter.
Press 1 for the Service Menu.
Press 2 for the Setup Menu.
Press 3 for the Management Menu.
Press 4 for the Enrollment Menu.
Press 5 for the Security Menu.
3. Press ENTER and the first command option in the selected menu appears.
If Users are
Enrolled in the
HandPunch
1. The display appears as follows.
ENTER ID
*:
2. Enter your ID number on the keypad and place your hand on the platen for
verification.
3. If verification is successful, the display appears as follows.
Enter Command Menu
ENTER PASSWORD
4. Press the default password for the menu you wish to enter.
Press 1 for the Service Menu.
Press 2 for the Setup Menu.
Press 3 for the Management Menu.
Press 4 for the Enrollment Menu.
Press 5 for the Security Menu.
5. Press ENTER
6. If you are authorized to use this command the first command option in the selected
menu appears.
7. If you are not authorized to enter this command the display appears as follows.
ENTER
*:
NOTE To access these menus you must be the first person enrolled in a new system installation
or you must have been enrolled as a supervisor. If you are blocked from the supervisory
menus, verify your access rights with management personnel. If enrollment information
has been incorrectly changed and you must have supervisory access to all menus, make
these changes through software.
NOTE It is possible to physically reset the HandPunch’s memory, however resetting memory
sets all unit parameters back to the factory default values. Resetting memory allows
access to all menus by the first person enrolled (as if it is a new system installation), but
this means that all employee information programmed into the HandPunch is lost and
must be re-entered manually. Be sure you need to reset memory before performing this
function. To reset memory, refer to the Erasing HandPunch Memory section on page 19.
22
HandPunch 1000 Manual
Navigating
Command
Menus
Once you have entered a command menu, there are three options available for navigating
the command menu system.
1. Press # to enter the command shown on the display.
2. Press * to step to the next command in the menu.
3. Press CLEAR to exit the command menu (pressing any numeric key also exits the
command menu). If you are in a command’s sub-menu, you may have to press
ENTER multiple times to completely exit the command menu.
23
Programming the HandPunch
The HandPunch is programmed via a series of command menus. A summary of the
menus and commands is given in Table 3.
Table 3: Basic Command Mode Structure
Service Menu
Setup Menu
Management Menu
Enrollment Menu
Security Menu
Password 1
Password 2
Password 3
Password 4
Password 5
Calibrate
Set Language
List Users
Add Employee
Status Display
Set Date Format
Set User Data
Add Supervisor
Set Time and Date
Special Enroll
Remove User
Set Address
Set ID Length
Set Serial
Upgrade
To control access to the command menus, each menu has a unique password. This
password is requested as a part of the process for accessing each menu. A supervisor
must enter the correct password for that menu to access that menu. The default menu
passwords are given in Table 3.
To increase the security of the HandPunch, Schlage Biometrics recommends changing
the passwords for the command menus to new numbers. These password numbers can
be up to 10 digits long. This is done with the Set Passwords command described on.
Autority Level
A second method for controlling access to the command menus is through the use
of Authority Levels. Authority Levels control whether or not a user has access to the
command menus.
• Level 0 is for a user who does not need access to any of the command menus.
• Level 5 is assigned to Supervisors who need access to all of the command menus.
HandPunch 1000 Manual
The HandPunch automatically assigns Authority Level 0 to users enrolled by the Add
Employee command. Authority Level 5 is automatically assigned to users enrolled by the
Add Supervisor command.
NOTE Until a user has been assigned to Supervisor, every user can access every menu. Once
a user has been enrolled using the Add Supervisor (designated as a supervisor), all
further user authority levels are assigned. The first person enrolled should be enrolled
using the Add Supervisor command. This protects the integrity of the system. Schlage
Biometrics strongly recommends enrolling at least two users as supervisors to ensure
that more than one person has the authority to access all menus and all commands.
Programming Order
When setting up HandPunch operations there is a general programming/operations order
that should be followed.
Set HandPunch Site Parameters – Set the HandPunch site parameters to meet site-
specific needs and usage: change the language used by the display, set the HandPunch’s address, and set the serial communication baud rate (used if you have installed a serial printer – see page 30).
Enroll Supervisory Staff – Enroll yourself and the supervisors who will have responsibility for HandPunch management. This is done through the Enrollment Menu (see Supervisor Enrollment on page 37).
NOTE The time, date, and ID number length are normally set by the host computer. However,
a supervisor can change these parameters at a HandPunch after setup information has
been downloaded from the host computer.
These tasks are done through the Setup Menu. The instructions for reader setup parameters begin on page 30.
Train and Enroll Users – Train each user regarding HandPunch usage and then Enroll each user. This is done through the Enrollment Menu. The instructions for employee enrollment begin on page 37. Special enrollment allows you to enroll people with disabilities that prevent them from using the HandPunch properly. Employees with special enrollment ID numbers can punch in without biometric verification.
NOTE This means that anyone who knows a special enrollment ID number can punch in.
This function should only be used if absolutely necessary. The instructions for special
enrollment begin on page 38
25
Programming the HandPunch
System Management
Once a HandPunch system is in operation the following commands are used for system
management.
List Users – List the Users authorized to use a HandPunch. This is done through the Management Menu. The instructions for listing employees begin on page 33.
Set User Data – Set a user’s reject threshold (adjusting the sensitivity applied when a HandPunch reads a hand) this task is done through the Management Menu. The instructions for setting user data begin on page 33.
Remove User – Remove employees (and supervisors) from a HandPunch. This is done through the Enrollment Menu. The instructions for removing employees begin on page 37.
26
HandPunch 1000 Manual
Service Menu
The Service menu commands provide information that help you determine if the
HandPunch is performing within normal operating parameters and identify the status
of the unit’s inputs and outputs. The following section provides a brief summary of the
Service Menu commands.
NOTE There are no user serviceable parts inside the HandPunch.
Navigating
the Service
Command
Menu
Enter the appropriate password to enter the Service command menu. Once you have
entered the command menu, there are three options available for navigating the
command menu system.
• Press # to enter the command shown on the display.
• Press * to step to the next command in the menu.
• Press CLEAR to exit the command menu (pressing any numeric key also exits the
command menu). If you are in a command’s sub-menu, press ENTER multiple times to
completely exit the command menu.
Service
Commands
There are two commands available from the Service command menu.
• Calibrate
• Status Display
Refer to Table 4 and identify the command you need to perform. Step through all previous
commands until you reach the desired command.
Table 4: Service Command Menu
Service Menu
Password = 1
Calibrate
Recal (Y/N)
Status Display
On/Off (Y/N)
27
Programming the HandPunch
Calibrate
The Calibrate command displays the HandPunch’s exposure values, allowing you to verify
these values are within normal operating parameters. The standard operating parameters
are shown in Table 5
.
Table 5: Normal Operating Parameters
Parameter
Status Display
Normal Range
Row “r”
0 +/- 2
Column “c”
0 +/- 2
Exposure “e”
100 +/- 20
The status display command allow you to enable or disable the displaying of the following
information.
• the status values of HandPunch inputs and outputs
• the hand read score of the last user to verify on the system
When the status display is enabled, Figure 8-1 identifies each status display field value
- ENTER ID O C O C O H L H L NN
O C O C O
H L H L NN
Last Hand Read Score
Aux Out 2
Aux Out 1
* Aux Out 0
* Lock
Aux In 2
Request to Exit
Aux In 1
Door Monitor Switch
Tamper
These Input/Output
values do not apply to
the HandPunch 1000
* These status values are inactive if the
reader is in Card Reader Output Mode.
O = Circuit Open
C = Circuit Closed
Figure 8-1: Status Display Chart
28
H = Output is OFF (High)
L = Output is ON (Low)
.
HandPunch 1000 Manual
Setup Menu
The Setup menu commands allow you to set the basic operating parameters for the
HandPunch unit. The following section provides a brief summary of all the parameters
that may be set on a HandPunch unit.
NOTE Once in the Command Menu, you can step through and set the parameters for each
command sequentially. You do not have to exit command mode after setting any
individual command.
Navigating
the Setup
Command
Menu
Enter the appropriate password to enter the Setup command menu. Once you have
entered the command menu, there are three options available for navigating the
command menu system.
• Press # to enter the command shown on the display.
• Press * to step to the next command in the menu.
• Press CLEAR to exit the command menu (pressing any numeric key also exits the
command menu). If you are in a command’s sub-menu, press CLEAR multiple times to
completely exit the command menu.
Setup
Commands
There are six commands available from the Setup command menu.
•
•
•
•
•
•
Set Language
Set Date Format
Set Date and Time
Set Address
Set ID Length
Set Serial
Refer to Table 6 on page 30 and identify the command you need to perform. Step through
all previous commands until you reach the desired command.
29
Programming the HandPunch
Table 6: Setup Command Menu
Setup Menu
Password = 2
Set Language
Select Language
Set Date Format
Select Date Format
Set Time and Date
Month (MM)
Day (DD)
Year (YY)
Hour (HH)
Minute (MM)
Set Address
New Address
Set ID Length
New ID Length
Set T & A Mode
Set Serial
RS-232
Select Baud Rate
Upgrade
Code
30
HandPunch 1000 Manual
Set Language
Set Date
Format
The Set Language command allows the language shown on the HandPunch’s display to
be “localized” for a variety of countries.
- English
- German
- Japanese
- Russian
- French
- Indonesian
- Italian
- Portuguese
- Spanish
- Polish
The Set Date Format command allows the date format shown on the HandPunch’s
display to be “localized” for a variety of countries.
mm/dd/yy
-mm-dd-yy
dd-MMM-yy
-MMM dd,yy
dd-mm-yy
-ddMMMyyyy
dd/mm/yy
Set Time and
Date
The Set Time and Date command allows the HandPunch’s time and date to be set. This is
normally not necessary as the HandPunch’s time and date are set by the host computer.
Set Address
The Set Address command allows a unique address to be set for each HandPunch in
a network. For proper operation, each HandPunch in the network must have a unique
address. All units may use any address from 0 to 254. All units are sent with the address
set to 1.
Set ID Length
The Set ID Length command allows you to reduce the number of keystrokes required to
enter the ID number by eliminating the use of the ENTER key to complete an ID number
entry. Once the ID Length is set, the HandPunch will automatically accept an ID number
entry once the correct number of characters have been entered.
Set ID Length does not apply when ID entry is made from a card reader. Once the ID
Length is set, the T & A Mode Set command appears, allowing you to configure the
HandPunch to prepare punch data for time and attendance software.
Set Serial
The Set Serial command allows you to set the baud rate communication parameters.
Upgrade
This Upgrade Menu is where the HandPunch code gets input to allow for a Memory
Upgrade
31
Programming the HandPunch
Management Menu
The Management menu commands allow you to manage employee data stored in a
HandPunch unit. The following section provides a brief summary of the employee data
that may be manipulated on a HandPunch unit.
Navigating
the Setup
Command
Menu
Enter the appropriate password to enter the Setup command menu. Once you have
entered the command menu, there are three options available for navigating the
command menu system.
• Press # to enter the command shown on the display.
• Press * to step to the next command in the menu.
• Press CLEAR to exit the command menu (pressing any numeric key also exits the
command menu). If you are in a command’s sub-menu, press CLEAR multiple times to
completely exit the command menu.
Management
Commands
There are four commands available from the Management command menu.
• List Users
• Set User Data
Refer to Table 7 and identify the command you need to perform. Step through all previous
commands until you reach the desired command.
Table 7: Setup Command Menu
Setup Menu
Password = 3
List Users
Display
Print
Set User Data
User Reject
32
HandPunch 1000 Manual
List Users
The List Users command allows you to display or print a list of all the employees enrolled
in a HandPunch.
Set User Data
The Set User Data command allows you to set an employee’s Reject Threshold, adjusting
the hand read threshold for one employee without affecting the threshold of other
employees. This task should be done through your user software, however it can be done
through the Management Menu.
33
Programming the HandPunch
Enrollment Menu
Enrollment is the process of recording a hand image and associating it with an ID
number. The first person to enroll in the HandPunch has access to all command menus.
This person should enroll using the Add Supervisor command (see page 37). Once a
supervisor has been enrolled, all further enrollments use the following rules:
• A user enrolled through the Add Employee command (page 37) is assigned Authority
Level 0. This allows the user to punch in and/or gain access through a door secured by
the HandPunch.
• A user enrolled through the Add Supervisor command (see page 37) is assigned
Authority Level 5. This allows the supervisor to punch in and gain access through a
door secured by the HandPunch, and it allows the supervisor to access all command
menus.
NOTE Until a user has been assigned to Authority Level 5 using the Add Supervisor command,
every user with Authority Level 0 can access every menu. This is done to ensure that
the first person enrolled is able to access all the menus to perform all the programming
required to support the HandPunch. Once a user has been enrolled using the Add
Supervisor command, all further user authority levels are assigned as per the list above.
This protects the integrity of the system by enacting the Authority Level rules described
above. Schlage Biometrics strongly recommends enrolling at least two users as
supervisors to ensure that more than one person has the authority to access all menus
and all commands.
Advance planning and training make enrollment fast and easy. Users should be informed
on what to expect and how to place their hands on the HandPunch before you enroll
them.
Navigating
the Setup
Command
Menu
Enter the appropriate password to enter the Setup command menu. Once you have
entered the command menu, there are three options available for navigating the
command menu system.
• Press # to enter the command shown on the display.
• Press * to step to the next command in the menu.
• Press CLEAR to exit the command menu (pressing any numeric key also exits the
command menu). If you are in a command’s sub-menu, press CLEAR multiple times to
completely exit the command menu.
34
HandPunch 1000 Manual
Preparation
Here are a few guidelines to help you prepare for an enrollment session.
• You can enroll one person or a group of people during an enrollment session.
• Each user must have a unique personal identification (ID) number. It will save you
considerable time if you assign the ID numbers in advance.
• The HandPunch will not accept two people with the same ID number.
• If you enroll people using the last four digits of their phone numbers or social security
numbers, you may get duplicate numbers.
• If you are enrolling large groups of people you may consider using an enrollment
trainer. It is a replica of a platen that is available through your Schlage Biometrics
reseller.
User Education
The HandPunch is easy to use and non-threatening. However, most people have never
used a biometric HandPunch. Training users on how the HandPunch works and how to
use it will eliminate most fears and concerns before they occur. Inform the users of these
facts.
•
•
•
•
•
•
Proper Hand
Placement
The HandPunch reads the shape of the hand, not the fingerprints or palmprints.
It does not identify people. It confirms people’s identity.
It scans with an invisible light of the type used in TV remote controls.
It does not transfer germs any more than a doorknob or money.
It does not invade privacy; it guarantees it.
The enrollment process requires three or more reads to collect enough information to
create a template.
For correct, consistent hand reads it is very important that your hand is placed on
the platen in the same manner every time. The following rules apply for proper hand
placement on the platen also refer to Figure 8-2 bellow.
• If you are wearing a ring, rotate the ring so the stone faces up in its normal position.
• Slide your right hand onto the platen rather like an airplane landing at the airport.
• Slide your hand forward until the web between your index and middle finger stops
against the Web Pin.
• Keep your hand flat. You should feel the surface of the platen on your palm and the
underside of your fingers.
• Close your fingers together until they touch the Finger Pins and watch the hand
diagram light display on the top panel.
• The lights go out when you have properly placed your fingers. If a light remains on, a
finger is not in proper contact with its Finger Pin.
WEB PIN
Figure 8-2: Placing Your Hand on the Platen
35
Programming the HandPunch
Left Hand
Enrollment
Some right hands cannot be used in the HandPunch due to disabilities such as missing
fingers. You can enroll a user with the left hand facing palm side up. The techniques for
left hand enrollment are the same as for standard enrollment. The user should keep the
back of the hand flat against the platen and move the fingers against the web pin and
the finger pins in the same manner as in standard enrollment. Users enrolled with the
left hand must always verify with the left hand. Extra practice on placing the hand on the
platen may be required to ensure correct, consistent hand reads.
Read Score
When a user uses the HandPunch the display appears as follows.
OKAY (USER ID)
SCORE IS: (SCORE NUMBER)
The score number on the display reflects how accurately the user’s hand is placed on
the platen. Scores that vary greatly between low and high numbers are indicative of
inconsistent hand placement. Scores above 50 are indicative of improper hand placement
or of a drastic change in the physical appearance of the hand.
When this occurs, emphasize the importance of sliding the hand onto the platen and
keeping the hand flat. Re-training and practice should lower a user’s score. It might
be necessary to change a user’s reject threshold if the user has a mild disability. Reenrollment might be necessary to create a new user template.
36
HandPunch 1000 Manual
Enrollment
Commands
There are three commands available from the Enrollment command menu.
• Add Employee
• Add Supervisor
• Remove User
Refer to Table 12 to identify the command you need to perform. Step through all previous
commands until you reach the desired command.
Table 8: Enrollment Command Menu
Service Menu
Password = 4
Add Employee
ID #
Add Supervisor
ID
Remove User
ID
Add Employee
The Add Employee command allows you to enroll a new employee into the HandPunch.
Add Supervisor
The Add Supervisor command allows you to enroll a new supervisor into the HandPunch.
Remove User
The Remove User command allows you to remove an employee or supervisor from the
HandPunch.
37
Programming the HandPunch
Special Menu
The Special menu has one command – Special Enroll. This command accommodates
users with disabilities that make it difficult or impossible to use a HandPunch in its
standard way. The following section provides a brief description of the Special Menu
command.
Navigating
the Special
Command
Menu
Enter the appropriate password to enter the Special command menu. Once you have
entered the command menu, there are three options available for navigating the
command menu system.
• Press # to enter the command shown on the display.
• Press * to step to the next command in the menu.
• Press CLEAR to exit the command menu (pressing any numeric key also exits the
command menu). If you are in a command’s sub-menu, press CLEAR multiple times to
completely exit the command menu.
Special
Command
There is one command available from the Special command menu.
• Special Enroll
Refer to Table 9 and identify the command you need to perform. Step through all previous
commands until you reach the desired command.
Table 9: Special Command Menu
Special Menu
Password = 5
Special Enroll
ID
On/Off (Y/N)
Special Enroll
The Special Enroll command allows a user to be enrolled such that the ID number is the
primary criteria for determining access. A hand read is required, but is not verified against
any stored identification data. A time zone value can be applied to the Special Enrollment
ID number to limit access times. The HandPunch default is for no time zone to be applied.
NOTE Special Enrollment affects the integrity of the HandPunch terminal and should only be
used as a last resort. Anyone who knows a Special Enroll ID number is granted access
when the ID number is used. Before specially enrolling a user, try to alleviate verification
problems by adjusting the individual user’s reject threshold (see page 36) or by using left
hand enrollment (see page 36).
38
HandPunch Maintenance
A minimum amount of system maintenance is required to keep HandPunchs fully
functional. HandPunchs should be cleaned periodically to prevent an accumulation
of dust from affecting the HandPunch’s readability. User Scores should be reviewed
periodically to ensure the HandPunch is performing properly.
NOTE There are NO user serviceable parts inside the HandPunch.
Once a HandPunch system is in operation there are two HandPunch commands that can
assist with system maintenance. These commands are performed through the Service
Menu. The instructions for these commands begin on page 24.
• Calibrate – View HandPunch exposure values.
• Status Display – Display HandPunch input/output status, the hand read score of the
last user to verify on the system.
Cleaning the
HandPunch
Inspect and clean the HandPunch regularly to maintain optimum performance. Clean
the platen, side mirror, reflector, and the window above the platen using a clean cloth
dampened with ordinary, non-abrasive window cleaner (see Figure 9-1). Start at the rear
corners of the platen and work your way forward.
NOTE DO NOT SPRAY CLEANING FLUID DIRECTLY INTO OR ON THE HandPunch.
Figure 9-1: HandPunch Cleaning
HandPunch Maintenance
User Score
40
Periodically check users’ scores (refer to the Read Score section on page 36). Scores
should average under 30. Occasionally a user will score above 30. This is not necessarily
an indication of poor performance. If a number of scores average over 30, clean the
HandPunch and check scores again. If scores remain high, or if users are experiencing
frequent rejections, run the Calibration command (see page 28).
HandPunch 1000 Manual
Appendix A
Tips for a successful Installation
HandPunch
• Think of the HandPunch as a camera
• Clean the HandPunch before it gets dirty
• Use non-abrasive cleaners such as glass cleaners and non-abrasive and clean cloths
• Make cleaning the HandPunch part of Janitorial program
• Do not remove the foam backing from the wall mounting plate
• Seal any holes made in the wall for wire routing, so that dust will not blow into the
HandPunch
Location
• Mount all HandPunchs in a network so that the top of the platen is 40” off of the floor
• If an enrollment HandPunch is used make sure that it is placed with the top platen 40”
off of the floor and not sitting directly on top of a desk, this will help to eliminate “bad
enrollments”
• Mount the HandPunch so that it is not difficult or dangerous to verify then open the
door
• It is not recommended to mount the HandPunch in an area where there is airborne
dust, in the path of direct sunlight, or where the HandPunch can be exposed to water
or corrosive gasses
Enrollment
• Educate the Enrollee on Hand Geometry
• Explain enrollment process
• Train Enrollee on hand placement
-- Practice placing hand on platen
-- Rotate rings to be stone-up
-- Make sure hand is flat on platen
-- Close finger towards the center of hand
-- Fingers gently touch finger pins
• Let the enrollee enter in their own ID number during the enrollment process, this forces
the Enroller to step aside allowing the Enrollee to stand in front of the HandPunch
helping to eliminate “bad enrollments”
• If an enrollment transaction fails:
-- Retrain the user on correct placement and ensure that rings are rotated to be
stone-up then Rotate rings to be stone-up
-- Try again to enroll the same handClose finger towards the center of hand
-- try to enroll the other hand (with the hand placed upside-down so the thumb still
contacts the thumb-pin on the platen)
• After enrollment, it is a good idea to let the enrollee enter their ID number and practice
a verification transaction to ensure that the enrollment was high-quality
• If a user consistently fails during verifications days/months/years later, re-enroll the
user to ensure a high quality and up-to-date enrollment record
41
Appendix B - Board Configuration Differences
Appendix B
Noted Board Configuration Differences
Because of Schlage Biometrics’ camera retrofit of the HandPunch some changes have
been made to the main PCB and they are listed as follows:
• Dipswitches have been removed
-- memory is reset with a push-button reset and user interface with keypad and LCD
• Power has moved to the right side of the PCB
• The RS-232 RJ-45 receptacle has been replaced with a 4 pin Molex connector on the
left side of the PCB
• A 2 pin Molex connector (J5) has been added to the board, next to the reset button,
to supply power for the LEDs. This connector should never be unplugged. unless a
modem or Ethernet is added to the PCB
• The upgrading of the memory is now handled through software codes at the
HandPunch. Contact Order Entry for memory upgrades
Memory Reset
To reset the memory of the HandPunch follow these steps1. Remove power and battery jumper, if a back up battery is installed
2. Press down on reset button and apply power
3. Release button
4. Reader will boot to
ERASE
:1 SETUP
:9 ALL!!!
• Press 1 to erase setup i.e. address, outputs, passwords, but retain user database and
datalogs
• Press 9 to erase everything i.e. HandPunch goes back to factory defaults
42
HandPunch 1000 Manual
Appendix C
Mechanical Installation
Select an installation location based on the guidelines provided in the Planning an
Installation section beginning on page 8.
Wall Plate Installation
Wall Preparation
For the following procedure protect the HandPunch from the dust and debris generated
during the wall plate installation process.
1. Remove the wall plate from the packing carton. Refer to Figure 12-1 for all wall plate
references in the following section.
LEVELING HOLE
2 UPPER SCREWS
SURFACE
CONDUIT
ENTRY
3 LOWER SCREWS
Figure 12-1: Wall Plate
2. Measure and mark a point 48 1/2 inches (123 cm) from the surface of the finished
floor. This point will correspond to the Leveling Hole where the top-center point of the
HandPunch should be mounted.
3. For a hollow wall, drive a small nail into the wall at the mark and hang the wall plate
from the Leveling Hole located near the top of the wall plate.
4. For a solid wall, hold the wall plate against the wall, centering the Leveling Hole over
the mark in the wall.Mechanical Installation
43
Appendix C
5.
6. Align a bubble level with the top edge of the wall plate and gently rotate the wall plate
until the bubble level shows that the top edge of the wall plate is level.
7. Secure the plate to the wall using heavy masking tape.
8. Using the wall plate as a template, mark the locations of the two upper screw holes
and the three lower screw holes.
9. For a concealed wiring connection, trace the outline of the open area in the center
of the wall plate. Identify and mark a 1/2 inch hole through which the HandPunch’s
wiring will be mounted.
10. For a surface conduit wiring connection, mark the two conduit clamp holes at the right
side of the wall plate.
11. Remove the wall plate, masking tape, and the nail (if used).
Mounting the
Wall Plate
1. For a hollow wall, use the provided hardware to mount the wall plate. Use the two
auger style fasteners for the upper two mounting holes. Use the toggle bolts for the
three lower mounting holes.
2. For a solid wall, use expansion bolts to mount the wall plate. For all five mounting
holes, drill a 1/4 inch diameter hole, 1/4 of an inch deeper than the length of the
expansion anchor.
Routing the
Wiring
1. Refer to Figure 12-2 on page 45 for a template diagram to assist in routing wiring.
2. For a concealed wiring connection, drill a 1/2 inch hole in a convenient location within
the open area of the wall plate. Pull the wiring to enter the HandPunch through this
hole in the open area.
3. For a surface conduit wiring connection, drill a 1/4 inch diameter hole, 1/4 of an inch
deeper than the length of the expansion anchor for each of the two conduit clamp
holes. Route 1/2 inch, flexible conduit to the HandPunch, ending the conduit between
the two conduit clamp holes. Pull the wiring to enter the HandPunch through the
conduit. Pull 18 inches of wire past the end of the conduit to allow enough space for
final connection to the HandPunch.
4. Clear all dust and debris away from the HandPunch mounting location.
44
HandPunch 1000 Manual
Wall Plate
SURFACE
CONDUIT
ENTRY POINT
CL
50" Reference
(127 cm)
to Top of
Wall Plate
42.75"
(108.6 cm)
CL HandPunch
42.5"
(108 cm)
Finished Floor
Figure 12-2: HandPunch Wire Routing Layout
NOTE Dust and debris surrounding the HandPunch can drastically affect the terminal’s
operation. It is important to ensure the HandPunch mounting location is free from dust
and debris.
Attaching the
HandPunch
1. Loosen the three bottom mounting screws until there is approximately 1/8 inch (3
mm) clearance between the screw head and the wall plate.
2. Remove the HandPunch from its carton.
3. At the base of the HandPunch is a piano hinge with three keyhole shaped slots that
correspond with the three lower mounting screws. Align and hang the HandPunch
from the three lower mounting screws (see Figure 12-3 on page 46).
4. Tighten all three lower mounting screws.
5. The HandPunch is now ready for its wiring connections.
45
Appendix C
LEVELING HOLE
2 UPPER SCREWS
SURFACE
CONDUIT
ENTRY
KEYHOLE
HOLES
3 LOWER
MOUNTING
SCREWS
REAR OF TERMINAL
Figure 12-3: Attaching the HandPunch to the Wall Plate
46
HandPunch 1000 Manual
Wiring Connections
Once the HandPunch is attached to the wall plate the wiring connections to the
HandPunch can be made (see Figure 12-4).
J7 Battery
Jumper
WALL
Serial RS-232
RJ-45 Jack
Power
Connectors
Wall Plate
Top of
Terminal
Optional Modem
5 4 3 2 1 OFF
ON
Top of HandPunch
Dip Switches
Figure 12-4: Wiring Connections and Dip Switches
Wiring
Examples
Table 10 on page 48 provides the pinouts for the RJ-45/RS-232 Serial Host Computer
Connection.
Figure 12-5 on page 48 provides a diagram of the RJ-45/RS-232 Connector.
Figure 12-7 on page 49 provides a Host PC to HandPunch Modem Network wiring diagram
(Modem wiring is a HandPunch option).
47
Appendix C
Table 10: RJ-45/RS-232 Serial Connection
J8 Pin
Signal
Connection
1
RJ
- not used -
2
CD
- not used -
3
DTR
- not used -
4
GND
Ground
5
Rx Data
Receive Data Input (from external device)
6
Tx Data
Transmit Data Output (to external device)
7
CTS
- not used -
8
RTS
- not used -
J4 Pins
1 2 3 4 5 6 7
Figure 12-5: J4 - RJ-45/RS-232 Jack Pinout
48
HandPunch 1000 Manual
Recogn
ition
1
4
7
*
No
2
3
5
8
0
9
System
s Inc.
Serial Cable
Connection
to Serial
Converter
Connection
to Host
Computer
Clea
r
6
F1
F2
#
No
Yes
HandPunch
RJ-45
Serial Port
Ente
r
RS-232 Serial Unit
Host Computer
Figure 12-6: Host PC to RS-232 Connection
Recog
nition
1
4
7
*
No
2
3
5
8
0
#
No
Yes
s Inc.
Clea
HandPunch
RJ-11
Modem Port
RSI Supplied Cable (Black)
RJ-11
Jack
r
6
9
System
F1
F2
Ente
r
Modem Unit
RJ-11 Telephone Outlet
Figure 12-7: Host PC to HandPunch Modem Connection
49
Appendix C
Setting the DIP Switches
The DIP Switch settings perform three tasks for the HandPunch (see Figure 12-8).
• Set End of Line (EOL) Termination to match the type of termination needed by the
network.
• Set the Communication Method to match the type of network used.
• Erase Memory to clear HandPunch memory to all factory default values and also clear
all user memory.
WA L L
5 4 3 2 1
OFF
ON
E O L Te r m i n a t i o n
E O L Te r m i n a t i o n
Communication Method
Erase Hand Reader Setup
Erase Hand Reader Setup and Database
TOP OF HAND READER
Figure 12-8: HandPunch Dip Switches
50
HandPunch 1000 Manual
End of Line
Termination
Termination helps to ensure clean data signals are transmitted through the network
wiring. Termination is applied to the end-of-line (EOL) HandPunch in the network daisychain. The factory default setting is for EOL termination to be disabled – switches 1 and 2
OFF. Refer to Figure 12-8 on page 50 for switch ON/OFF positioning.
• To enable EOL termination at a HandPunch, both switches 1 and 2 must be ON.
• To disable EOL termination at a HandPunch, both switches 1 and 2 must be OFF.
EOL Termination must be enabled for:
• A single HandPunch terminal installation.
• In a Modem to PC network the HandPunch terminal with the Modem option (for
communication with the host computer).
Communication
Method
The factory default setting and for standard operation, switch 3 must be OFF.
• Switch 3 must always be OFF.
Erasing
HandPunch
Memory
The erase memory function can perform either or both of the following:
• Erase a HandPunch’s configuration data.
• Erase a HandPunch’s user database and transaction buffer.
The factory default setting (and normal operation setting) is for switches 4 and 5 to be
OFF, retaining memory.
If the HandPunch is equipped with the battery backup option, remove shunt J7 in front
of the DIP switch array (see Figure 12-4 on page 47) before proceeding. Replace shunt J7
after completion of the following steps.
Erasing the HandPunch Setup
Perform the following steps to erase the configuration data but retain the user database.
With system power OFF, set switch 4 ON.
Turn system power ON and wait for HandPunch boot information to appear on the display.
Turn switch 4 OFF.
51
Appendix C
Erasing the
HandPunch
Setup and User
Database
Perform the following steps to erase both the configuration data and the user database.
1. With system power OFF, set both switches 4 and 5 ON.
2. Turn system power ON and wait 5 seconds.
3. Turn both switches 4 and 5 OFF.
NOTE Before putting the HandPunch into service ensure DIP switches 4 and 5 are both OFF.
If switches 4 and 5 are not off, the next time the HandPunch’s power is cycled the
HandPunch’s memory will be erased.
52
HandPunch 1000 Manual
Closing the HandPunch
Before closing the HandPunch, ensure dip switches 4 and 5 are OFF (refer to Figure
12-8 on page 50). Clear all dust and debris away from the HandPunch. With the wall mount
latch in the unlocked position, swing the body of the HandPunch up and lock the latch into
place with the key provided with the HandPunch (see Figure 12-9).
NOTE Dust and debris surrounding the HandPunch can drastically affect the terminal’s
operation. It is important to ensure the HandPunch is free from dust and debris before
closing the terminal.
NOTE Do not force the HandPunch onto the wall mount latch when the latch is in the locked
position.
Wa l l P l a t e
etsyS
m
.cnI s
goceR
noitin
Latch
Key
oN
LOCK
Unlocked Position
Wa l l P l a t e
Latch
Key
Locked Position
Figure 12-9: Closing the HandPunch
53
Appendix D - Troubleshooting Guide
Appendix D
Troubleshooting Guide
Display Messages During Verification
Various messages can appear on the HandPunch’s display during hand verification.
These messages are defined in Table 18.
Table 11: Display Messages During Verification
Message
Definition
PLACE HAND
The platen is ready to receive your hand for verification.
ID VERIFIED
You are verified, proceed.
REMOVE HAND
Remove your hand and place it on the platen again. Follow
proper hand placement rules.
TRY AGAIN
Your attempt was rejected. Repeat verification following proper
hand placement rules.
ID REFUSED
Your rejections exceeded the maximum number of tries
allowed. Wait until another employee has verified and try again
or call your supervisor
ENTER ID
You entered your ID number incorrectly or your access time is
restricted.
• If the display shows TRY AGAIN, you are not verified. You may have made an error
in entering your ID number or in placing your hand on the platen. Re-enter your ID
number and try again, taking care to follow proper hand placement rules (see page 35).
•
• If the display shows TIME RESTRICTION, you are not authorized to punch in at this
time. If this seems to be in error, contact your supervisor about time restrictions.
•
• After a pre-programmed number of denied attempts, an ID number will no longer be
accepted and the display will appear as follows.
ID INVALID
TEMPORARILY
54
HandPunch 1000 Manual
This is called a “lockout.” Before the rejected ID number can be used again, another
employee or a supervisor must successfully verify at the HandPunch.
• If you enter your ID number, but do not place your hand on the platen, the HandPunch
will time-out in about 25 seconds. You can immediately end this time-out by pressing
the CLEAR key.
Beeper and LED Status During Verification
The HandPunch’s beeper and LED status display also display hand verification
information. This information is defined in Table 19.
Beeper and LED Status During Verification
Operation
Beeps
LED
Meaning
During Keypad
Entry
1 per Keystroke
­–
Keystroke Accepted
After ID Entry
–
–
OK - Proceed
After ID Entry
2
–
ID Number Not in
Database
After Hand
Placement
1
Green
ID Verified
After Hand
Placement
2
Red
ID Not Verified Try Again
After Hand
Placement
1 Long
Continuous
Red
ID Refused
55
Glossary
Address, HandPunch A HandPunch Address is a unique identification number
assigned to a HandPunch. Each HandPunch on a network
must be assigned a unique address.
AWG American Wire Gauge is a U.S. standard set of wire conductor
sizes. The “gauge” refers to the diameter of the wire. The higher
the gauge number, the smaller the diameter, the thinner the
wire, and the greater the electrical resistance. Thicker, smaller
gauge wire carries more current because it has less electrical
resistance over a given length. Thicker wire is better for long
wire distances.
HandPunch Address See Address, HandPunch
Platen The Platen is the flat surface at the base of the HandPunch,
on which a user places his/her hand for enrollment and
verification. The platen has guide pins to ensure the user’s
fingers are consistently positioned correctly.
Template A Template is a set of data generated for a user. It is made
up of the user’s enrollment information and any system
configuration parameters that are assigned to the user. The
template is stored at each HandPunch and can be stored at
the host computer with the Time and Attendance software.
Transaction A Transaction is any kind of event recorded at a HandPunch.
Transactions may include In or Out punches, department
transfers, and supervisor edits.
HandPunch 1000 Manual
Limited Warranty
Schlage Biometrics, Inc. (the “Company”) warrants to the original user the products
manufactured by the Company (the “Product”) to be free of defects in material and
workmanship for a period of three months from the date of purchase by such user or six
months from the date of shipment from the factory, whichever is sooner, provided:
1. The Company has been notified within such period by return of any alleged defective
product, free and clear of all liens and encumbrances, to the Company or its
authorized dealer, transportation prepaid; and
2. The Product has not been abused, misused, or improperly maintained and/or
repaired during such period; and
3. Such defect has not been caused by ordinary wear and tear; and
4. Such defect is not the result of voltage surges/brownouts, lightning, water damage/
flooding, fire, explosion, earthquakes, tornadoes, acts of aggression/war, or similar
phenomenon; and
5. Accessories used as integral to the Product have been approved by the Company.
The Company shall, at its option, either repair or replace, free of charge, the Product
found, upon the Company’s inspection, to be so defective, or if agreed upon, refund
the purchase price, less a reasonable allowance for depreciation, in exchange for the
Product.
THE COMPANY MAKES NO OTHER WARRANTY AND ALL IMPLIED WARRANTIES
INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE EXPRESSED
WARRANTY PERIOD AS SET FORTH ABOVE.
THE COMPANY’S MAXIMUM LIABILITY THEREUNDER IS LIMITED TO THE
PURCHASE PRICE OF THE PRODUCT. IN NO EVENT SHALL THE COMPANY
BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, INCIDENTAL, OR SPECIAL
DAMAGES OF ANY NATURE ARISING FROM THE SAME OR THE USE OF THE
PRODUCT.
Schlage Biometrics Inc. reserves the right to make changes in the design of any of its
products without incurring any obligation to make the same change on units previously
purchased.
57
Ingersoll Rand’s Security Technologies Sector is a leading global provider of products and services that
make environments safe, secure, and productive. The Sector’s market-leading products include electronic
and biometric access control systems; time and attendance and personnel scheduling systems; mechanical
locks and portable security, door closures and exit devices, steel doors and frames, architectural hardware
and technologies and services for global security markets.
866.861.2480
Schlage
Biometric Solutions
Ingersoll Rand Security Technologies
538 Oakmead Parkway
Sunnyvale, CA 94085
Office: 866-861-2480/512-712-1413 (international)
Fax: 866-303-1794/408-341-4101
E-mail: sbssupport@irco.com
www.schlage.com
©2011 Ingersoll-Rand Company Limited
www.ingersollrand.com
P/N 70100-6009 Rev. 3.3 07/11