SP3000 DDR3 DIMM Tester
DDR3
1600
CST Inc, leading worldwide manufacturer of
memory tester and automation is proud to
introduce the most affordable, high
performance and stand alone DDR3 Memory
DIMM Tester. The SP3000 tester is specially
designed for high volume memory
distributors, memory module manufacturers,
dealers and service depots.
The SP3000 DDR3 Tester comes with a
standard 240pin DIMM socket for testing the
latest 1600, 1333, 1066 MHz DDR3 memory
modules at “Real Bus Speed ~ 1600Mhz” and
“Real Cycle Time Testing”.
The SP3000 DDR3 DIMM Tester is built with
flexible architecture to support DRAM,
SDRAM, DDR & DDR2 Memory Module testing
with a change of optional adapter.
SP3000 DDR3 Feature
Auto Identify:
Memory Type: 240pin DIMM Unbuffered and
Registered DIMM
Memory Configuration
Memory Size
Memory Frequency
ECC or Non-ECC
Real Bus Speed Testing
Real Cycle Time and At-Speed Testing (True
1600Mhz Frequency)
Uses state-of-the-art DDR3 controller
Super Fast Detail Test time(4GB in 20secs)
Effective Test Algorithm
Automatic Read/ Write Leveling & ZQ
Calibration
Quick test, checks for assembly faults
Detail March test, checks for functional failures
Programming and check SPD
Fault Focusing – pinpoints to faulty chip(s)
Ease of Use
Easy to read LCD display
5 Easy Push Button Selection
Output bad results to printer
Audible buzzer for pass/fail indication
- Colored LED for Test, Pass and Fail status
Ez Upgrading
Firmware upgradeable
Support wide range of test adapters
Support RoboFlex2 & RoboFlex3 Handler
- Interface with PC software via RS232 Port
Technical Specification
Clock Frequency
Data-rate
Address depth
Data width
No of Ranks
Voltage range
CAS Read Latency
Trcd & Trp Adjustment
Cas Write Latency
Internal bank
Burst Chop Mode
Dynamic ODT selection
ZQ adjustment
Refresh Cycle
Static Test Pattern
Dynamic Test Pattern
SPD Programming
: 400,533,666,800 MHz selectable
: 800 ,1066 ,1333 & 1600 Mhz
: 4 Giga-word (16 Row x 12 Col)
: Up to 72 bit
: 1,2 and 4 Rank
: 1.35, 1.4, 1.5, 1.6, 1.7, 1.8, 1.9 & 2.0
: 5, 6, 7,8,9,10 & 11 Clocks
: 5, 6, 7 ,8,9,10 & 11 Clocks
: 5, 6, 7, 8, 9 & 10 Clocks
: 8 Banks
: Fixed BL8, BL4 & On the Fly
: 40, 60 & 120 ohm (Auto Select)
: Auto Calibration
: Auto / Self Refresh
: Walk Data , Walk Address , DQS,
DQM, CKE, CS, CKE Test
: Mat-S, March-C, March-X,
March Y and Moving Inversion
: Read/Write & Editable Byte 0 – 255
Reversible SPD Write Protect
General Specification
DDR3 Test Adapter
: 240 Pin DDR3 DIMM (Standard)
204 Pin SODIMM Converters
Power Adapter
: input 100 /250 Vac, 50 /60Hz
Output 12 VDC @ 3A
Operating Temperature : 15 ~110 Degree F
Dimension
: 9.25” x 9.25” x 2”
Weight
: 6 pounds
CST Inc , 2336 Lu Field Road , Dallas Texas 75229 Tel : (972) 241-2662 Fax : (972) 241-2661
www.simmtester.com
Email : info@simmtester.com
1
The SP3000 DDR3 Memory Tester
The CST SP3000 DDR3 1700Mhz Adapter is the latest test adapter for the SP3000. It supports testing
of 240-pin PC3-6400, PC3-8500, PC3-10600, and PC3-12800 DDR3 memory, including unbuffered
(UDIMM) and registered modules (RDIMM), both ECC and non-ECC, that comply with JEDEC
standards.
The SP3000 DDR3 adapter plugs into the existing SP3000 base tester. This makes the DDR3 adapter
by far the most cost-effective solution for testing high-speed DDR3 modules.
2
No special setup is required. As with all of CST products, the adapter is simple to use. Insert the DDR3 adapter,
turn the SP3000 tester on, insert a DDR3 DIMM module into the heavy duty Yamaichi test socket, then press the
start button to begin testing.
CST has incorporated latest state-of-the-art technology "Memory Controller” in the design of the new SP3000
DDR3 1600Mhz DDR3 Adapter.
DDR3 Advanced Technology
•
Main Adapter DDR3 controller featuring improved 1600MHz test engine.
•
High efficiency switching power regulator to generate the DDR3 STTL-15 interface power source.
•
Build in analog circuit for measuring the module's current, voltages and the board's temperature.
•
User Programmable controlled Vtt regulator.
•
400-1700 MHz DDR3 clock generator.
•
High resolution VDD high efficiency switching power regulator.
The SP3000 DDR3 1700Mhz adapter includes many new features which are relevant to the differences between
DDR3 technology and the older DDR2 and DDR technology. As with all of CST SP3000 testers, each DIMM
module's size, structure, and type are automatically detected, without the need for user's setup. The test flow
follows our standard Basic Test, Extensive Test, and Auto-Loop process. The SP3000 DDR3 adapter is very
simple to operate, with little training or setup required.
DDR3 Test Features
•
Supports Burst Length of 4 & 8
•
Supports CAS LATENCY (CL) in the range of 5,6,7,8,9,10 & 11.
•
Trcd & Trp is supported in the range of 5,6,7,8,9,10 and 11.
•
Support On-Die-Termination (ODT)
•
DDR3 Data rates: 800,1066,1333,1600 MHz Test engine. Higher speed DDR3 modules such as 1866
MHz ,2 GHz can still be tested at a lower frequency.
•
Supports new DDR3 reset function and the mode registers enhancements.
•
Improved current and temperature sensing circuitry.
•
True 1.5V testing with a wide support range of 1.35V to 2.0V
•
Parallel testing capability of 64/72-bits.
•
Heavy Duty , 240-pin test-quality for convenient module handling.
•
Automatic detection and support for Registered/Unbuffered DIMM modules.
•
Automatic detects x4 or x8 chip type
•
Support up to 16 rows and 12 column address lines to support 32 GB modules.
•
Complete SPD programming support.
•
Option 204-pin SODIMM Stacked converter modules available.
3
BASIC Operation
4
For ordering:
SP3000 DDR3 1600Mhz DIMM Tester set: SP3-DDR3-1600
SP3000 DDR3 1600Mhz SODIM Tester set: S3P-DDR3-1600S
5