function and controls 1. lamp shade 2. display 3. light on

UR220 / English Manual
FUNCTION AND CONTROLS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
LAMP SHADE
DISPLAY
LIGHT ON-OFF
TO SET THE LIGHT INTENSITY LOW
TO SET THE LIGHT INTENSITY HIGH
MOOD LIGHT ON –OFF / MOOD LIGHT SELECT
TIME SET / TEMPERATURE / MEMORY / MEMORY+
SNOOZE / SLEEP / DIMMER
SOURCE/ DISPLAY OFF
<< / TUNE - / YEAR/MONTH-DAY / C-F / BETWEEN DISPLAY CONTENTS
ON-OFF / NATURAL SOUND SELECT <<
>> / TUNE + / NAP / DST / NATURAL SOUND SELECT >>
ALARM 1 CONTROL / VOLUME DOWN
ALARM 2 CONTROL / VOLUME UP
ON / OFF / ALARM OFF
AUX IN JACK
DC POWER INPUT
TEMPERATURE SENSOR (IN DOOR)
SPEAKER
RATING LABEL (BOTTOM OF UNIT)
FM ANTENNA
BATTERY COMPARTMENT (BOTTOM OF UNIT)
UR220 / English Manual
REMOTE CONTROL
The remote control works on one 3V "CR2025 type" lithium battery (included). To
active the remote control, remove the insulation tab inserted in the battery
compartment. To remove the tab, pull it in the direction of the arrow as shown in
the illustration.
If the operation of the remote control becomes unsatisfactory, replace the original
battery with a new 3-volt lithium battery of the same type.
1. Slide out the battery holder from the remote control case. (see diagram).
2. Replace the weak/dead battery with a new one. Be sure the battery is
installed correctly. The remote control will not work if the battery is
installed with wrong polarity,
CAUTION: Danger of explosion if the battery is replaced incorrectly.
Replace only with the same or equivalent type of battery.
3. Insert the battery holder back into the battery slot.
NOTE: Only use a well-known brand of cell battery to ensure the longest life and
best performance.
UR220 / English Manual
1. ON/OFF / ALARM OFF
2. SOURCE / DISPLAY OFF
3. SNOOZE / SLEEP / DIMMER
4. LIGHT ON/OFF
5. MOOD LIGHT ON / OFF
6. TEMPERATURE / C-F
7. << / TUNE - / BETWEEN DISPLAY CONTENTS ON-OFF
8. ALARM 1 CONTROL
9. VOLUME DOWN
10. ALARM 2 CONTROL
11. >> / TUNE + / NAP / DST
12. TIME SET / MEMORY / MEMORY+
13. YEAR/MONTH-DAY
14. VOLUME UP
15. NATURAL SOUND SELECT
16. MOOD LIGHT SELECT (To turn the unit RGB color changing or to stop the
MOOD LIGHT color changing.)
17. TO SET THE LIGHT INTENSITY HIGH
18. TO SET THE LIGHT INTENSITY LOW
UR220 / English Manual
LED DISPLAY MODE
Get started
•Select a proper place for the device such as a dry, and even non slip area
where you can easily operate the device.
•Inserting the Battery (Backup)
INSTALLING/REPLACING THE BACK-UP BATTERY
This unit is equipped with a battery back-up system, requiring one DC3V
CR2032 lithium battery (not included) to maintain the time/calendar settings and
radio presets during AC power outage.
1. Unscrew and remove the BATTERY COMPARTMENT COVER.
2. Install one fresh CR2032 lithium battery into the battery compartment following
the polarity diagram on the BATTERY COMPARTMENT COVER. Use only the
specified size and type of battery.
3. Replace the BATTERY COMPARTMENT COVER and tighten its screw.
Note: The unit will operate without a battery installed but your time & alarm
setting and radio presets will be lost and will have to be reset in the event of
power interruption or failure.
IMPORTANT:
Be sure that the battery is installed correctly. Wrong polarity may damage the unit
and void the warranty. For best performance and longer operating time, we
recommend the use of good quality alkaline battery.
UR220 / English Manual
AC POWER CONNECTION
Plug the AC power cord into a household outlet AC source.
SETTING THE CALENDAR AND TIME
1. In standby mode, press and hold the unit button (7) or the remote control
button (12) for about 2 seconds to enter the calendar/time set mode.
2. The year indicator will flash on the LED DISPLAY for up to 30 seconds
prompting for a new entry.
3. While the display is flashing, repeatedly tap the unit buttons (10), (11) or the
remote control button (7), (11) to adjust to the correct year. Press and hold the
unit (10), (11) button or the remote control button (7), (11) for faster scanning
backward or forward. Tap the unit button (7) or the remote control button (12) to
confirm.
4. Repeat steps #2 to #3 to adjust the month, day, time format, current hour and
finally current minute in the same way.
Notes:
-The display sequence in calendar / time set mode will be as follows:
Year → Month → Date → 12/24 Hour Time Format → Real Time Hour →
Real Time Min → Normal Time
-To check the year while current time is displayed, tap the unit button (10) or the
remote control button (13) once. The LED DISPLAY will change to year display
for 5 seconds and then revert to current time automatically.
-To check the date while current time is displayed, tap the unit button (10) or the
remote control button (13) twice. The LED DISPLAY will change to date display
for 5 seconds and then revert to current time automatically.
-During the time set, if no button is being pressed within 10 seconds, the current
display time will be automatically stored.
-Make sure the hour is set so that the PM indicator is displayed correctly for
afternoon/night times.
Switching the Unit On/Off
Press the unit on/off button (14) or the remote control on/off button (1) to switch
the unit on or off.
Volume Adjust
Press the unit (12) and (13) button or the remote control button (9) and (14)
button to set the desired volume level. The volume level reading will appear in
the LED DISPLAY.
UR220 / English Manual
Display Brightness (in standby)
In standby mode, Press the unit DIMMER button (8) or the remote control
DIMMER button (3) to adjust the display brightness.
Display on/off function
•In standby mode, press and hold unit SOURCE button (9) or the remote control
SOURCE button (2) for 3 seconds. “ON” appears on the display (2).
•After 15 seconds, the display (2) turns off.
•Press any button to turn the display (2) on for another 15 seconds.
•To deactivate the display on/off function, press and hold unit SOURCE button (9)
or the remote control SOURCE button (2) for 3 seconds. “OFF” appears on the
display (2).
Reading light function
1. Press the unit button (3) or the remote control button (4) to turn on the
function.
2. Use the unit button (5) or the remote control button (17) to increase the
brightness. use the unit button (4) or the remote control button (18) to reduce the
brightness.
3. In order to turn off the function, press the button again.
Mood light
1. Press the unit button (6) or the remote control button (5) to turn on the mood
light. The light will alternate in different colors.
2. Press and hold the unit button (6) for about 3 seconds or Press the remote
control button (16) to stop or start the mood light color changing.
3. In order to turn off the mood light, press the unit button (6) or the remote
control button (5) again.
Toggle temperature display between °C (Celsius) and °F (Fahrenheit)
1. Press the device to standby mode using the unit button (14) or the remote
control button (1).
2. Press the unit button (7) or the remote control button (6) to display the
temperature.
3. While the temperature is displayed, press the unit button (10) or the remote
control button (6) for about 3 seconds to switch between °C and °F.
RADIO TUNING
1. In standby mode, Press the unit on/off button (14) or the remote control on/off
button(1) to turn the unit ‘On’.
2. The LED DISPLAY will show the radio frequency for about 5 seconds and then
revert to normal time display.
UR220 / English Manual
AUTOMATIC SEARCH FOR RADIO STATIONS
To automatically search for stations with strong signals, press and hold the main
unit button (10) and (11) or the remote control button (7) and (11) until the
frequency readout on the display begins to scan. Release the button. The tuner
will stop on the first strong station it finds.
MANUAL SEARCH FOR RADIO STATIONS
1. Tap the unit (10) and (11) button or the remote control button (7) and (11)
repeatedly to choose your desired radio station.
2. Tap the unit (12) and (13) button or the remote control button (9) and (14) to
set the desired volume level. The volume level reading will appear in the LED
DISPLAY.
Notes:
- Use manual tuning to select weaker stations that might be skipped during
automatic tuning.
- If the automatic tuning does not stop on the exact frequency of the station, for
example, it stops on 88.9 MHz instead of 88.8 MHz, use the manual tuning
method to “fine tune” to the exact frequency of the desired station.
HINTS FOR BEST RECEPTION
FM - To insure maximum FM tuner reception, unwrap and fully extend the
EXTERNAL FM WIRE ANTENNA for best FM radio reception.
TO SET/RECALL RADIO STATION PRESETS
1. Press the unit button (10) and (11) or the remote control button (7) and (11)
select the desired radio station.
2. Press and hold the unit (7) button or the remote control button (12), the next
available preset memory number will flash on the LED display. (Note: “P01” will
flash in the display if you are programming presets for the first time.)
3. Press the unit button (10) and (11) or the remote control button (7) and (11) to
change to the desired preset number P01 thru P10.
4. Repeat steps #1 thru #3 to preset up to10 FM stations.
5. To recall one of the preset stations already programmed, Press the unit
button (7) or the remote control button (12) repeatedly until you reach the desired
preset number/radio station.
UR220 / English Manual
ALARM SETTING
You can set two alarm times. 6 different alarm options are available: Radio +
Light / Radio / Buzzer + Light / Buzzer / Natural sound + Light / Natural sound.
The setting sequence for AL1 and AL2 is as follows:
In radio off mode, Press the main unit alarm set buttons (12) and (13) or the
remote control buttons (8) and (10) to show the alarm time. Afterwards keep
depress the unit alarm set button (12) and (13) or the remote control button (8)
and (10) over 2 seconds to enter the alarm set mode. After enter the setting
mode, press the unit alarm set button (12) and (13) to change the mode cycle as
follows:
SETTING THE ALARM 1 (BEEPER)
Normal Time→ AL 1 Hour → AL 1 Min → AL 1 weekday Alarm → AL 1 beeper
→Light → Light intensity → Normal Time.
SETTING THE ALARM 1 (RADIO)
Normal Time → AL 1 Hour → AL 1 Minute → AL 1 weekday → AL 1 beeper
→ AL 1 radio → AL 1 final radio volume →AL 1 Light → AL 1 Light intensity →
Normal Time.
SETTING THE ALARM 1 (NATURAL SOUND)
Normal Time → AL 1 Hour → AL 1 Minute → AL 1 weekday → AL 1 beeper
→ AL 1 radio →AL 1 natural sound →(Use the unit buttons (10) and (11) or the
remote control buttons (7) and (11) to select the desired natural sound) →AL 1
final natural sound volume →AL 1 Light → AL 1 Light intensity → Normal Time
SETTING THE ALARM 2 (BEEPER)
Normal Time→ AL 2 Hour → AL 2 Min → AL 2 weekday Alarm → AL 2 beeper
→Light → Light intensity → Normal Time.
SETTING THE ALARM 2 (RADIO)
Normal Time → AL 2 Hour → AL 2 Minute → AL 2 weekday → AL 2 beeper
→ AL 2 radio → AL 2 final radio volume →AL 2 Light → AL 2 Light intensity →
Normal Time.
SETTING THE ALARM 2 (NATURAL SOUND)
Normal Time → AL 2 Hour → AL 2 Minute → AL 2 weekday → AL 2 beeper
→ AL 2 radio →AL 2 natural sound →(Use the unit buttons (10) and (11) or the
remote control buttons (7) and (11) to select the desired natural sound) →AL 2
final natural sound volume →AL 2 Light → AL 2 Light intensity → Normal Time.
UR220 / English Manual
Proceed as follows:
1. In standby mode, Press the unit Alarm1 button (12) or the remote control
button (8). The currently set alarm time is shown.
2. Keep the button pressed for approx. 3 seconds when the alarm time is
displayed. The hours of the currently set alarm time start to flash.
3. Use the unit buttons (10) and (11) or the remote control button (7) and (11) for
setting.
4. Press the unit Alarm 1 button (12) or the remote control button (8) for
confirmation. The minutes start to flash.
5. Use the unit buttons (10) and (11) or the remote control button (7) and (11) for
setting.
6. Now select the days you want the alarm to sound. The following selections can
be made:
• 1-5 = Monday to Friday
• 1-7 = Monday to Sunday
• 6-7 = Saturday and Sunday
• 1-1 = Weekday
6a. When you have selected the setting 1-1:
1. Press the button to select the weekday.
2. Make your selection with the buttons and.
(1 = Monday, 2 = Tuesday, 3 = Wednesday, 4 = Thursday, 5 = Friday, 6 =
Saturday, 7 = Sunday)
7. Press the button to confirm. Then select how you want to be awakened. Select
from:
• “bu” (buzzer):
A buzzer sounds when the alarm time is reached.
The buzzer interval increases from slow to fast. The volume cannot be adjusted.
• Radio frequency is displayed:
As soon as your set alarm time is shown, the radio switches on. The last set
station is played. The volume increases slowly to the set volume. The volume
cannot be adjusted.
• NS (natural sound):
As soon as your set alarm time is shown, the natural sound switches on. The
natural sound is played. The volume increases slowly to the set volume. The
volume cannot be adjusted.
UR220 / English Manual
NOTE:
• The alarm function turns off automatically after 30 minutes until the next day.
7a. If you want to be awakened by a radio station, select the maximum alarm
volume using the unit (10) and (11) buttons or the remote control (7) and (11)
buttons.
8. Press the unit Alarm 1 button (12) or the remote control Alarm 1 button (8) to
confirm. Then select the light intensity (L ) for the alarm function. Selecting
“OFF ” will cancel this function.
NOTE:
The light inside the lamp shade (1) will turn on 30 minutes prior to the pre-set
alarm time. The brightness will gradually increase, starting at the intensity level
previously set.
9. Finally, press the button again. The first alarm time is now activated.
To set the second alarm time, repeat the above steps with the main unit Alarm 2
button (13) or the remote control Alarm 2 button (10).
NOTE:
• If the alarm time has been activated, AL1 or AL2 will appear in the display.
• In order to briefly display the set alarm times, press the unit Alarm 1 button (12)
or the remote control Alarm 1 button (8) , respectively the unit Alarm 2 button (13)
or the remote control Alarm 2 button (10).
Turning off the Alarm Press the unit on/off button (14) or the remote control on/off
button (1) to stop the alarm.
Deactivate the Alarm Function
1. Switch the device to standby with the unit button (14) or the remote control
button (1).
2. To deactivate the alarm function, press and hold the main unit button (12) and
(13) or the remote control button (8) and (10) for about 3 seconds . AL1 or AL2
will disappear.
SNOOZE FUNCTION (MAIN UNIT)
When the alarm source is sounding, press the unit any buttons (except on/off
button (14)) or the remote control SNOOZE button(3) to suspend the alarm and
activate the snooze function. The Alarm will temporarily stop and sound again 9
minutes later but the AL1 (or AL2) indicator will keep flashing.
Notes:
This manual snooze operation can be repeated again and again.
To turn off the snooze function, Press the main unit on/off button(14) or the
remote control on/off button (1). The AL1 (or AL2) INDICATOR will stop flashing
UR220 / English Manual
SLEEP OPERATION
The sleep timer allows you to turn the unit off after a designated time has
elapsed.
1. While listening to the radio, tap the unit button SLEEP button (8) or the remote
control button (3) the sleep time ‘90’ (minutes) appears in the LED DISPLAY.
2. Repeatedly tap the SLEEP button to select a sleep timer of 90, 60, 30 or 15
minutes. Wait for about 10 seconds after your selection for the unit to confirm the
selection, the unit will play for the selected length of time then turn itself ‘Off’
automatically.
3. To cancel the sleep timer, repeatedly tap the SLEEP button until you see the
current time in the LED DISPLAY after last sleep timer option (15 minutes).
•This function can be cancelled with the button (14).
4. This function can be cancelled with the unit button (14) or the remote control
button (1).
Note:
There is no sleep indicator in this unit. To check the remaining sleep time, tap the
SLEEP button once.
Nap alarm
The nap alarm can be used for e.g. a short “nap”. The function only operates in
standby.
• Press the unit button (11) or the remote control button (11) to select the time
after which the device will beep. Select from 90 to 10 minutes or OFF (off) in
steps of 10 minutes.
• After the selected time has elapsed, an increasingly fast beep will sound. Use
the unit button (14) or the remote control button (1) to turn off the beep.
Note: When using the NAP alarm the wake up light function is inactive.
NATURAL SOUND
1. In standby mode, tap the unit ON-OFF button (14) or the remote control
ON-OFF button (1) to turn the unit ‘On’.
2. Press the unit button (9) or the remote control button (2) to switch to natural
sound mode.
3. Use the main unit buttons (10) and (11) or the remote control button (15) to
select the desired natural sound.
DAYLIGHT SAVING TIME (DST) MODE
If daylight saving time (DST) is available in the summer time in your State, you
may use this option to adjust to the correct time easily.
1. In standby mode, press and hold the unit DST button (11) or the remote
control button (11) for 2 seconds to advance the displayed time by one hour.
2. To cancel DST mode, repeat the above operation.
UR220 / English Manual
AUX IN JACK
(Cable not included)
1. If required, use a suitable adapter (not included).
Connect the external device as follows :
• With a 3.5 mm stereo jack plug to the AUX IN socket (15).
2. Turn the device on using the unit button (14) or the remote control button (1).
Press the unit button (9) or the remote control button (2) to switch to AUX IN
mode. AUX IN appears in the display.
3. Start the playback of your audio source. Listen to the sound playback via the
speaker. You can adjust the volume using the unit buttons (12/13) or the remote
control button (9/14).
4. For the further procedure, please refer to the user manual of the external audio
source.
NOTE:
If possible, adjust the volume of the external unit to a comfortable level.
Stop AUX IN operation
Disconnect the cable from the AUX IN jack. Press the unit on/off button (14) or
the remote control button (1) to turn the unit off.
UR220 / English Manual
ALTERNATE DISPLAY BETWEEN TIME AND TEMPERATURE MONTH-DATE
DISPLAY
1. In radio off mode, press and hold the unit button (10) or the remote control
button (7) for about 3 seconds until “ON” appears in the LED DISPLAY.
2. The DISPLAY will alternate between the current Time for 10 seconds and
month- date for 5 seconds and temperature for 5 seconds as follows:
To cancel this function, press and hold the unit button (10) or the remote control
button (7) for about 3 seconds until “OFF” appears on the LED DISPLAY. The
DISPLAY will switch back to normal time display.
NOTE
If you replace the battery, do not disconnect AC plug from AC outlet. Otherwise,
current time and alarm will be initialized.
RESETTING
If the system does not respond or exhibits erratic or intermittent operation, you
may have experienced an electrostatic discharge (ESD) or a power surge that
triggered the internal microcontroller to shut down automatically. If this occurs,
simply disconnect the ac power cord and remove the system backup battery, wait
for at least 3 minutes and then setup the unit again as if it is a brand new unit.
SPECIFICATIONS
Frequency range: FM 87.5 – 108 MHz
In door Temperature Sensor Range: 32 °F to 122 °F (0°C to +50°C)
Battery backup: 3V (CR2032 Flat Lithium battery x 1)
Power Adaptor: Input AC 100-240V 50- 60 Hz
Output DC 5V 1200mA
Specifications are subject to change without further notice.
Copyright by Wörlein GmbH, D 90556 Cadolzburg.