Contents The Range of Remote Control Signal Reception Description of The Projector’s Interface keystone correction horizontal(±15°) How to use TRONFY TP60 How to connect the projector with iphone5/5s/6/6plus and ipad device What cable do I need to connect a laptop without HDMI port How to connect a laptop with projector with HDMI or VGA cable What do I need to run this with video from my Android phone /Tablet Can I use the projector with HDMI cable directly From a TV or PC Can I connect the DVD player with AV Slot About the Projection Distance and Projection Size Short throw projector How to change the Aspect Ratio What’s about the 5V-OUT USB and the other USB How to set up the projector's color The projector would have to rotate/Horizontal flip OFF as a whole 180 degrees The projector how set up the Language How to Mount a Projector How to reduce the noise of projector’s fan Over Temperature Protection (Dolby) Could the projector support the power point presentations How can you get a better movie experience Not image and sound / Shuts off automatically Have sound no image, Have image no sound The Range of Remote Control Signal Reception: The Remote Control Uses 2 XAAA 1.5v batteries (Not included) Don’t use the new and old battery at the same time in remote control, otherwise power shortage and will affect remote control use .please pick the battery out if no use for long time. When operating remote control , please make sure that the signal emission of the remote control aims the infrared receiving interface of projector. Description of The Projector’s Interface Signal Source selection : Press signal source selection button(Input) on the remote control, then press up or down button to select the signal source you need , then “ok”. SD Card Interface USB 2.0 Slot : Projector is only a device for projecting images. The USB port is only for U-Disk/Hard Disk Device connecting, NOT support reads the data from iPhone/ iPad/ Android Smartphones. Out 5V Interface: 5V-Output USB for Mobile Tablet power supply.This means the usb output is only for power supply.（NOT FOR iphone, iPad charging.） HDMI Input Interface: HD decoding : Support 1080P HD decoding ,whether HD video ,pictures, music,movie,e-books can be played. VGA Interface: If you connect the projector with VGA Interface, there is a picture but no sound. Unless using a VGA cable with audio. The Signal Source of Remote Control: Remote Control must be aligned to The Signal Source, which can control the projector. Headphone jack: Quiet enjoyment, you can connect the headphone to avoid affecting other people. 【For perfect sound, we recommend customer connecting to an external speaker(Via the 3.5 mm headphone jack, or via the 3-In-1 audio& video port).】 AV Interface: We generally do not recommend you to use the AV Interface, because there is only Picture but no sound. Output information is missing, displaying black and white screen. keystone correction horizontal(±15°) How to use TRONFY TP60 Image focus: place the projector vertical to the projection screen, and then Turn the rotary button slightly, until the brilliant image presented. FAQ: How to connect the projector with iphone5/5s/6/6plus and ipad device : The projector can be connected with iPhone/iPad by HDMI input slot. You need to have a Lighting Digital AV Adapter LOCALLY. 1. Connect the HDMI TO HDMI Cable with Projector 2. Connect the HDMI to HDMI Cable with a Lightning Digital AV Adapter 3. Connect a Lightning Digital AV Adapter with your iPhone /ipad What cable do I need to connect a laptop without HDMI port: VGA!If the projector does not have a VGA input simply get a VGA toHDMI converter so that you can hook it up to your laptop. Connect the converter to your laptop then connect the HDMI and you are set. How to connect a laptop with projector with HDMI or VGA cable: If you connect the projector with VGA Interface, there is a picture but no sound. Unless using a VGA cable with audio. What do I need to run this with video from my Android phone /Tablet : You will need an HDMI cable with a micro connector to your phone and aregular size HDMI end to attach it to the projector. Make sure your Android phone is MHL ready, otherwise it won't work. You need to order the HDMI TO HDMI Cable and MHL Cable LOCALLY. Can I use the projector with HDMI cable directly From a TV or PC? All the projectors support HDMI-in input data. As long as ensure the output data of HDMI-out PC and TV function. But in general, most of the PC and TV only have HDMI-in, no HDMI output data output function. Please check if your television and PC have HDMI output function . Tips:1. For Connecting the PC with Projector : The traditional desktop computer, only have VGA interface, no HDMI. With VGA interface, we can link computer and desktop through the VGA line. Connection with the projector by VGA port , only project images, no sound. Can I connect the DVD player with AV Slot ? The projector has 3 in1 AV-IN slot , support av-in input data ,we need to ensure whether the DVD have AV-OUT data output function, most of the DVD only supports AV-IN, not support AV-OUT. PS：We do not recommend connecting devices through the AV port, it may cause image distortion, lack of color, lost voice, etc.. It will effect we inspect. When connection is completed, you should choose the Input Source: AV About the Projection Distance and ProjectionSize Projection Distance:1.5-4M;Projection Size:49-130inches. For Best Projection Distance:1.5-2.0M; best Projection Size:49-80 inches, for best User Experience. Can only adjust the size of the image by changing the distance. Short throw projector Our projector is not the SHORT THROW PROJECTOR (IF YOU LOOKING FOR Short throw projector please Google it FIRST) How to change the Aspect Ratio: We have researched this issue regarding the aspect ratio problem and made several tests below (Mainly decided by the picture/video sources ratio itself.) Here are the situations: 1. If connected via VGA port, the aspect ratio cannot be adjusted, it decided by the sources ratio at 4:3 or 16:9. 2. If connected via HDMI port, the aspect ratio can be adjusted, there are several modes: Auto, 16:9, zoom1,zoom 2…We tried to connect the projector with MacBook, select auto and the ratio is 4:3. When playing videos, we are able to adjust the image ratio, the ratio which being adjusted is the computer but not the sources. 3. If connected via HDMI port with Iphone6, it’s a fixed ratio and notable to be adjusted, decided by the sources itself, 4:3/16:9 4. If connected via USB port, it’s a fixed ratio and not able to be adjusted, decided by the sources itself, 4:3/16:9 What’s about the 5V-OUT USB and the other USB: Projector is only a device for projecting images, it only reads the data from USB drive directly via the USB input slot.USB Output 5V for Mobile Tablet power supply. This means the usb output is only for power supply.(You can refer to our iphone4/4S/5/5S/6/6 Plus/iPad for power supply. instructions in detail.)Not Support How to set up the projector's color: Please try the following Step: Turn on Projector (Use remote), Click Menu –Color Temperature Cool--- Click OK. There are four ways for you to choose, you can Click the left or right(Use remote) to choose. At the end of the User Mode, You can adjust the color according as you like. You can add or decrease the Number of the Red/Green/Blue to adjust the color. The projector would have to rotate/Horizontal flip OFF as a whole 180 degrees Please try the following Step: Turn on Projector (Use remote), Click Menu--- Choose Projector Mode Normal Fr..--- Click OK The projector how set up the Language Please try the following Step: Turn on Projector (Use remote), Click Menu---OSD Language English---Then you can choose the Language you want. How to Mount a Projector Part 1 of 3: Deciding on Screen Placement 1. Decide on the best location for the screen. 2. Decide on your screen height. 3. Know your screen size. Part 2 of 3: Deciding on Projector Placement 1. Calculate your projector’s throw distance. 2. Determine the best throw distance for your projector. 3. Find out your projector’s vertical offset. 4. Calculate the vertical placement of your projector. 5. Determine horizontal lens shift. Part 3 of 3: Mounting the Projector 1. Decide on the best mount to suit your projector and room. 2. Attach the mount. 3. Calculate the mount-to-lens distance and adjust throw distance Accordingly . 4. Secure the projector. 5. Secure the cables. 6. Adjust the projector settings to fine tune the image. When you complete all the steps, you can enjoy your Home theater life. Notice: When you use it, you should adjust the image 180 degrees flip first. Trouble Shooting How to reduce the noise of projector’s fan： Usually, when the projectors works, the fan will make noise when cooling off the high temperature. Please take a break after 3-4 hoursusing to avoid overheating. Besides, here are the tips to reduce the noise 1. Please use the projector in room temperature or low temperature, so the projector will heat slowly, and then the noise will be reduced. 2. Please use projector in the clean environment and seal it after using to get away from the dust. 3. If you use the projector about 3-6 months, the noise of projector will be louder, you can try to take apart it to clean the dust on the fan. Over Temperature Protection: If the temperature inside the projector rises too high, the over temperature projector will automatically turn off the lamp with the STATUS indicator blinking. Should this happen, do the following: * Unplug the power cable after the cooling fans stop. * Clean the ventilation holes if they are clogged with dust. * Wait about 60 minutes until the inside of the projector becomes cool enough. Dolby NOTICE: Due to the copyright issue of Dolby, this projector does not support Dolby's Audio decoding【Close the Dolby option of the device you connected】 Could the projector support the power point presentations? It supports PPT format, but please be aware that this projector is a simple projection equipment. It can support all the file you have in your Computer/Laptop device . But it doesn’t have any intelligent functions, such as read the office software in the U disk directly. (if you need this function ,please search for SMART android projector ) RECOMMENDED Not recommended for PPT or business presentation, ideal for home theater movies and video game use. Native Resolution:800*480, Contra st:800:1. (NEED TO US E IN DARK ENVIRONMENT) How can you get a better movie experience: It is important to note that with projectors in this price range, you need to have the room/ area you are viewing this projector as dark as possible. Overhead lights and especially sunlight will easily drown the light produced by this LED and will make the image quality suffer or make it impossible to actually see the image. This project is not meant for daytime viewing or viewing with the lights on. Now, that being said, in dark viewing, the image quality is actually fantastic! Not recommended for PPT or business presentation, ideal for home theater movies and video game use. Not image and sound / Shuts off automatically Take off the power supply for a second and restart the projector, Ensure the signal input connection is ok and choose the correct signal source. Sometimes if multiple devices are connected, there might be some Signal interference. You can turn off those equipment, leaving only the device you want to play. Have sound no image Ensure all cables are connected to the right slots, adjusted the value of the projector. (Connect the device throw by HDMI / USB slot) Have image no sound Connect the device throw by VGA, this situation is normal.VGA only supports picture but no sound, Check if the sound was disabled. This manual is for reference only ,If you have any question , please contact us through Amazon.