thinline vertical sliding unit details thinline vertical sliding

THINLINE
VERTICAL
SLIDING
UNIT
THINLINE VERTICAL SLIDING UNIT DETAILS
DETAILS Wall Mounted SUPPLEMENTAL HEAD HOUSING DETAIL WEIGHT THINLINE VERTICAL SLIDING UNIT PARTS LIST FOR 2-­‐PANEL UNIT Vertical Sliding Units are shipped knocked down in the following components: 1. Head h ousing (top section) 2. Left jamb housing 3. Right jamb h ousing 4. Fixed back p anel 5. Joint strip (required if b ack p anel is o ver 4 ’0” h igh) 6. Back p anel trim at h ead, jamb and sill 7. Sliding p anel 8. Accessory tray 9. Kick p anel (floor m ounted u nits o nly) K ick p anel for floor m ounted units are n ot furnished b y C laridge u nless ordered as an option. 10. Kick p anel b ottom m ounting angle screwed to floor (floor m ounted units only) 11. 2” m ounting clip angles 12. Counterweight (2 p er p anel) 13. Kick p anel trim at jambs (floor m ounted u nits o nly) 14. Rubber b umpers screwed to floor (floor m ounted u nits o nly) 15. Bottom housing (wall m ounted u nits only) INSTALLATION INSTRUCTIONS T HINLINE V ERTICAL SLIDING UNITS 11 Note: For two-­‐ and three-­‐track u nits, the tracks m ust b e separated and installed o ne track at a time p er the following steps: 1.
Fasten head housing (#1) to w all w ith 2 ” m ounting clips (#11) 12” on centers. U se ½ ” p an h ead screws to fasten h ousing clips. 2. Fasten o ne jamb h ousing (#2 left o r # 3 right) to w all and head housing (#1) w ith 2 ” m ounting angle clips 1 2” o n centers. U se 1” pan h ead screws to w all; ½ ” p an h ead screws to fasten housing to clips. Jamb housing m ust b e installed p lumb. 3. If u nit is w all-­‐mounted, fasten b ottom h ousing to w all and u pright with 2” m ounting clips spaced 1 2” on centers. P art (#15) illustrated on opposite side of sheet. 4. Insert b ack p anel trim (#4) from open side of u nit and fasten b ack panel to w all through b ack p anel trim (#6) w ith 1 -­‐1/2” p an head screws. If b ack p anel is o ver 4 ’0” h igh a joint strip (#5) is required. Screw b ack leg o f joint strip to w all u sing countersink screws. T his insures that back p anel snugs against w all and d oes n ot interfere with m ovement of the sliding p anel. 5. Set sliding p anels (#7) into u nit in lowered p osition. 6. Attach cables to p anels o n jamb h ousing (#2 o r # 3) o f u nit that is attached to w all. See cable travel layout illustration o n o pposite side o f sheet. 7. Position remaining u pright. A ttach counterweight cables to sliding panel o n remaining jamb h ousing w ith cable clamps in hardware package. 8. Fasten loose u pright to h ead h ousing. 9. Install rubber b umpers (#14 – Floor m ounted u nits only) to floor at each end o f sliding p anels. B umpers at h ead housing are factory installed. 10. Floor M ounted U nits o nly – Install kick p anel (#9 – o ptional, o r by o thers) b y inserting p anel side trim # 13) o ver edges o f kick panel jamb. Fasten b ottom of kick p anel into continuous m ounting angle (#10) at floor through b ottom face o f kick p anel. Screw trim to b ottom edge o f h ousing w ith ¼ ” p an h ead screws. Floor Mounted See reverse side for supplemental d rawing o f H ead H ousing and Wall M ounted D etails. If you require assistance during assembly, our Customer Service
team can help you!
Email custserv@demco.com or call 800.356.1200